HAWA Industrial

GRILLES & DIFFUSERS

New Industrial Area, Doha Qatar, TEL: +974 44152035, FAX: +974 44984151 ADDRESS: P.O. Box 90126
EMAIL: [email protected], WEBSITE: www.everythingducting.com
 CONTENTS
INTRODUCTION

GRILLES & REGISTRE

 SINGLE DEFLECTION GRILLE ADJASTABLE BLADES

 SINGLE DEFLECTION REGISTER ADJASTABLE BLADES

 DOUBLE DEFLECTION GRILLE ADJASTABLE BLADES

 DOUBLE DEFLECTION REGISTER ADJASTABLE BLADES

 CURVED GRILLE & REGISTER

 FIXED BLADE GRILLE

 FIXED BLADE REGISTER

 FRESH AIR GRILLES

 DECORATIVE GRILLE & REGISTER

 EGG CRATE GRILLE

 EGG CRATE REGISTER

 DOOR GRILLES –NON VISION GRILLE

 BAR GRILLES & REGISTERS

LINEAR
 SINGLE DEFLECTION LINEAR BAR GRILLE

 SINGLE DEFLECTION LINEAR BAR REGISTER

 DOUBLE DEFLECTION LINEAR BAR GRILLE

 DOUBLE DEFLECTION LINEAR BAR REGISTER

 SINGLE & DOUBLE DEFLECTION LINEAR BAR CURVED GRILLE & REGISTER

HAWA INDUSTRIAL
 LINEAR SLOT DIFFUSER
 SUPPLY LINEAR SLOT DIFFUSER

 RETURN LINEAR SLOT DIFFUSER

 CURVED SUPPLY & RETURN LINEAR SLOT

 SUPPLY & RETURN FLOW BAR DIFFUSER

CEILING DIFFUSER

 SUPPLY CEILING DIFFUSER

 RETURN CEILING DIFFUSER

 SUPPLY & RETURN ROUND DIFFUSER

 SUPPLY & RETURN PERFORATED DIFFUSER

JET DIFFUSER
 JET DIFFUSER–EYE BALL

 JET DIFFUSER -RING TYPE

DISCK VALVE

 SUPPLY & RETURN DISCK VALVE

AIR LOUVER
 FRESH AIR LOUVER

 EXHAUST AIR LOUVER

SAND TRAP LOUVER

 SAND TRAP LOUVER WITH FILTER

 FLUSH MOUNTED SAND TRAP LOUVER

HAWA INDUSTRIAL
 INTRODUCTION
HAWA industrial Is One of the Leading Manufacturers of
Aluminum Grilles, Diffusers, GI Ducts, and Pre-insulated
Duct & Accessories in Qatar. It was established since 27
years.
Our Rapid Growth Has Enabled Us to Establish New State
Of The Art Industrial Facilities, Which Utilize Technology
and Equipment’s To Produce More than 22,000 Pc’s Of Air
Inlet per Year in The Range of 200x15cm.
As an industry-leading manufacturer, our focus is to build
value in air. This is more than a catchy play on words. It’s
what we do. We offer the widest range of reliable air
movement and control equipment available. Then, we do
everything to exceed your expectations for on-time delivery,
easy installation, and performance.
HAWA manufactures those products which following the
international standards to meet your requirement. We also
have good strategically located gulf factories, so our
products are available when you need them.

HAWA INDUSTRIAL
GRILLES & REGISTRES

HAWA INDUSTRIAL
GRILLES & REGISTRES SDG-H / SDG-V

SINGLE DEFLECTION GRILLE ADJUSTABLE BLADES

The single deflection air grilles are the most desirable for the side wall locations. Since they are available with both
horizontal and vertical adjustable blades, minor air motion problems can be simply corrected by adjusting the
vanes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards
Blades mounting: Horizontal Blades mounting: Vertical
Description:
 Blades are individually adjustable to any degree
of deflection by hand without the use of special
tools.
 Interlocked corners and mechanically stacked to
SDG-V form a rigid frame.
SDG-H
 The horizontal and vertical vanes are provided
Standard Color: with nylon bushes for rattle free individually
As standard the grille is supplied in either off white RAL operation.
9010 or white RAL 9016 polyester powder paint.  Extruded aluminum blades with aero-foil cross
Standard Sizes Available: section for minimum turbulence.
 Auxiliary frames available on request for neat
Any combination of length and width:
and separable mounting in plaster and other wall
materials.
Dimensions  Borders are one piece construction in size
Neck Size (N) Face Size (F) C through 1200 mm x 1200 mm, for smooth
Inch mm Inch mm mm mm appearance and easy installation.
4 100 9 225 30 40  Maximum effective pressure areas can be
6 150 13.5 337 30 40 achieved when the blades are positioned at 0°
8 200 17 425 30 40 horizontal position.
10 250 20.5 512 30 40  If the grill width more than 500mm, a mullion
12 300 25 625 30 40 will be fixed at the center and for widths of one
14 350 29 725 30 40 meter and above, the number of mullions will be
16 400 31 775 30 40 two or more.
18 450 33 825 35 40  Fixing methods are same as all the grilles either
20 500 36.5 912 35 40 by screws or concealed clips.
24 600 40.5 1012 35 40

A 1 cm clearance is deducted from your order neck size. Option:

Ordering Data:  Frame width is available in (30 & 20mm)
 Grille available in vertical or horizontal type
Specify
 insect screen
 1. HAWA type and model  4. Type of fixing  Colors available upon request
 2. Nominal size - L x W  5. Surface finish  Foam gasket on the back of the frame provided
 3. Quantity  6. Remarks on request.
Example Note:
1 2 3 4 5 6
 “F” is face size
Concealed  “N” is actual neck size
SDG-H 900X500mm 50 nos. Ral 9010 Horizontal
type fixing  “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES SDR-H / SDR-V

SINGLE DEFLECTION REGISTER ADJUSTABLE BLADES

The single deflection air Registers are the most desirable for the side wall locations. Since they are available with
both horizontal and vertical adjustable blades, minor air motion problems can be simply corrected by adjusting the
vanes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards
Blades mounting: Horizontal Blades mounting: Vertical
Description:
 Blades are individually adjustable to any degree
of deflection by hand without the use of special
tools.
 Interlocked corners and mechanically stacked to
form a rigid frame.
 The horizontal and vertical vanes are provided
SDR-H SDR-V with nylon bushes for rattle free individually
operation.
Standard Color:
 Extruded aluminum blades with aero-foil cross
As standard the grille is supplied in either off white RAL section for minimum turbulence.
9010 or white RAL 9016 polyester powder paint.  Auxiliary frames available on request for neat
Standard Sizes Available: and separable mounting in plaster and other wall
Any combination of length and width: materials.
Dimensions  Opposed blade damper (OBD) operator is easily
adjusted through face with a screw driver.
Neck Size (N) Face Size (F) C
 Borders are one piece construction in size
Inch mm Inch mm mm mm
through 1200 mm x 1200 mm, for smooth
4 100 9 225 30 40 appearance and easy installation.
6 150 13.5 337 30 40  Maximum effective pressure areas can be
8 200 17 425 30 40 achieved when the blades are positioned at 0°
10 250 20.5 512 30 40 horizontal position.
12 300 25 625 30 40  If the grill width more than 500mm, a mullion
14 350 29 725 30 40 will be fixed at the center and for widths of one
16 400 31 775 30 40 meter and above, the number of mullions will be
18 450 33 825 35 40 two or more.
20 500 36.5 912 35 40  Fixing methods are same as all the grilles either
24 600 40.5 1012 35 40
by screws or concealed clips.

A 1 cm clearance is deducted from your order neck size. Option:
Ordering Data:  Frame width is available in (30 & 20mm)
 Grille available in vertical or horizontal type
Specify
 4. Type of fixing  Insect screen
 1. HAWA type and model  Colors available upon request
 5. Surface finish
 2. Nominal size - L x W  Foam gasket on the back of the frame provided
 3. Quantity  6. Remarks
on request.
Example
1 2 3 4 5 6 Note:
 “F” is face size
Concealed
SDR-H 900X500mm 50 nos. Ral 9010 Damper  “N” is actual neck size
type fixing
 “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES DDG-H / DDG-V

DOUBLE DEFLECTION GRILLE ADJUSTABLE BLADES

The double deflection air grilles are the most desirable for the side wall locations. Since they are available with both
horizontal and vertical adjustable blades, minor air motion problems can be simply corrected by adjusting the
vanes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards
Blades mounting: Horizontal Blades mounting: Vertical
Description:
 Blades are individually adjustable to any degree
of deflection by hand without the use of special
tools.
 Interlocked corners and mechanically stacked to
form a rigid frame.
DDG-H DDG-V  The horizontal and vertical vanes are provided
with nylon bushes for rattle free individually
Standard Color: operation.
As standard the grille is supplied in either off white RAL  Extruded aluminum blades with aero-foil cross
9010 or white RAL 9016 polyester powder paint. section for minimum turbulence.
Standard Sizes Available:  Auxiliary frames available on request for neat
and separable mounting in plaster and other wall
Any combination of length and width:
materials.
Dimensions  Borders are one piece construction in size
Neck Size (N) Face Size (F) C through 1200 mm x 1200 mm, for smooth
appearance and easy installation.
Inch mm Inch mm mm mm
 Maximum effective pressure areas can be
4 100 9 225 30 40
achieved when the blades are positioned at 0°
6 150 13.5 337 30 40
horizontal position.
8 200 17 425 30 40  If the grill width more than 500mm, a mullion
10 250 20.5 512 30 40 will be fixed at the center and for widths of one
12 300 25 625 30 40 meter and above, the number of mullions will be
14 350 29 725 30 40 two or more.
16 400 31 775 30 40  Fixing methods are same as all the grilles either
18 450 33 825 35 40 by screws or concealed clips.
20 500 36.5 912 35 40
24 600 40.5 1012 35 40
A 1 cm clearance is deducted from your order neck size. Option:
Ordering Data:  Frame width is available in (30 & 20mm)
 Grille available in vertical or horizontal type
Specify
 4. Type of fixing  Insect screen
 1. HAWA type and model  Colors available upon request
 5. Surface finish
 2. Nominal size - L x W  Foam gasket on the back of the frame provided
 3. Quantity  6. Remarks
on request.
Example
Note:
1 2 3 4 5 6  “F” is face size
DDG-H 900X500mm 50 nos.
Concealed
Ral 9010 Horizontal  “N” is actual neck size
type fixing  “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES DDR-H / DDR-V

DOUBLE DEFLECTION REGISTER ADJUSTABLE BLADES

The double deflection air registers are the most desirable for the side wall locations. Since they are available with
both horizontal and vertical adjustable blades, minor air motion problems can be simply corrected by adjusting the
vanes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards
Blades mounting: Horizontal Blades mounting: Vertical
Description:
 Blades are individually adjustable to any degree
of deflection by hand without the use of special
tools.
 Interlocked corners and mechanically stacked to
form a rigid frame.
 The horizontal and vertical vanes are provided
with nylon bushes for rattle free individually
DDR-H DDR-V operation.
Standard Color:  Extruded aluminum blades with aero-foil cross
As standard the grille is supplied in either off white RAL section for minimum turbulence.
9010 or white RAL 9016 polyester powder paint.  OBD painted black matt, are easily removable
Standard Sizes Available: and attached to the frame by (S) clips.
Any combination of length and width:  Opposed blade damper (OBD) operator is easily
adjusted through face with a screw driver.
Dimensions  Borders are one piece construction in size
Neck Size (N) Face Size (F) C through 1200 mm x 1200 mm, for smooth
Inch mm Inch mm mm mm appearance and easy installation.
4 100 9 225 30 40  Maximum effective pressure areas can be
6 150 13.5 337 30 40 achieved when the blades are positioned at 0°
8 200 17 425 30 40 horizontal position.
10 250 20.5 512 30 40  If the grill width more than 500mm, a mullion
will be fixed at the center and for widths of one
12 300 25 625 30 40
meter and above, the number of mullions will be
14 350 29 725 30 40
two or more.
16 400 31 775 30 40  Fixing methods are same as all the grilles either
18 450 33 825 35 40 by screws or concealed clips.
20 500 36.5 912 35 40
24 600 40.5 1012 35 40
A 1 cm clearance is deducted from your order neck size. Option:
Ordering Data:  Frame width is available in (30 & 20mm)
 Grille available in vertical or horizontal type
Specify
 4. Type of fixing  Insect screen
 1. HAWA type and model
 Colors available upon request
 2. Nominal size - L x W  5. Surface finish
 Foam gasket on the back of the frame provided
 3. Quantity  6. Remarks on request.
Example
Note:
1 2 3 4 5 6  “F” is face size
DDR-H 900X500mm 50 nos.
Concealed
Ral 9010 Damper  “N” is actual neck size
type fixing  “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES SDG-C/SDR-C/DDG-C/DDR-C
SINGLE –DOUBLE DEFLECTION CURVED GRILLE & REGISTER
Specializing in convex, concave and flat face curved grilles, we are able to facilitate architectural design elements
and incorporate engineering requirements to produce an aesthetically pleasing and functional product for any
space. Our customized curved grilles are available in a variety of sizes, radiuses, frames, styles, materials and
finishes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards

Description:
 Blades are individually adjustable to any degree
of deflection by hand without the use of special
tools.
 Interlocked corners and mechanically stacked to
form a rigid frame.
 The horizontal and vertical vanes are provided
with nylon bushes for rattle free individually
Standard Color: operation.
As standard the grille is supplied in either off white RAL  Extruded aluminum blades with aero-foil cross
section for minimum turbulence.
9010 or white RAL 9016 polyester powder paint.
 Auxiliary frames available on request for neat
Standard Sizes Available: and separable mounting in plaster and other wall
Any combination of length and width: materials.
Dimensions  Opposed blade damper (OBD) operator is easily
Neck Size (N) Face Size (F) C adjusted through face with a screw driver.
Inch mm Inch mm mm mm  Borders are one piece construction in size
through 1200 mm x 1200 mm, for smooth
4 100 9 225 30 40
appearance and easy installation.
6 150 13.5 337 30 40
 Maximum effective pressure areas can be
8 200 17 425 30 40 achieved when the blades are positioned at 0°
10 250 20.5 512 30 40 horizontal position.
12 300 25 625 30 40  If the grill width more than 500mm, a mullion
14 350 29 725 30 40 will be fixed at the center and for widths of one
16 400 31 775 30 40 meter and above, the number of mullions will be
18 450 33 825 35 40 two or more.
20 500 36.5 912 35 40  Fixing methods are same as all the grilles either
24 600 40.5 1012 35 40 by screws or concealed clips.

A 1 cm clearance is deducted from your order neck size. Option:
Ordering Data:  Frame width is available in (30mm & 20mm)
Specify  Grille available in vertical or horizontal type
 4. Type of fixing  Insect screen
 1. HAWA type and model
 2. Nominal size - L x W  5. Surface finish  Colors available upon request
 3. Quantity  6. Remarks  Foam gasket on the back of the frame provided
on request.
Example
Note:
1 2 3 4 5 6
 “F” is face size
Concealed Radius of  “N” is actual neck size
SDG-C 900X500mm 50 nos. Ral 9010
type fixing Curvature  “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES FBG/FBR
SINGLE DEFLECTION FIXED BLADE GRILLE & REGISTER

The single deflection fixed blades air grille & Registers are the same as the single deflection horizontal blade mounting
except the blades are fixed at 45°.
Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards

Blades mounting Description:

 Deflection blades are fixed rigidly to the frame

at an angle of 45° to the horizontal or vertical
plane.
 Interlocked corners and mechanically stacked to
form a rigid frame.
 Extruded aluminum blades with aero-foil cross
FBG FBR
section for minimum turbulence.
Standard Color:  Auxiliary frames available on request for neat
As standard the grille is supplied in either off white RAL and separable mounting in plaster and other wall
9010 or white RAL 9016 polyester powder paint. materials.
Standard Sizes Available:  Opposed blade damper (OBD) operator for the
Any combination of length and width: register is easily adjusted through face with a
screw driver.
Dimensions  Borders are one piece construction in size
Neck Size (N) Face Size (F) C through 1200 mm x 1200 mm, for smooth
Inch mm Inch mm mm mm appearance and easy installation.
4 100 9 225 30 40  If the grill width more than 500mm, a mullion
6 150 13.5 337 30 40 will be fixed at the center and for widths of one
8 200 17 425 30 40 meter and above, the number of mullions will be
10 250 20.5 512 30 40 two or more.
12 300 25 625 30 40  Fixing methods are same as all the grilles either
14 350 29 725 30 40 by screws or concealed clips.
16 400 31 775 30 40
18 450 33 825 35 40
20 500 36.5 912 35 40
24 600 40.5 1012 35 40
A 1 cm clearance is deducted from your order neck size. Option:
Ordering Data:  Frame width is available in (30 & 20mm)
Specify  Insect screen
 4. Type of fixing  Colors available upon request
 1. HAWA type and model
 5. Surface finish  Foam gasket on the back of the frame provided
 2. Nominal size - L x W
on request.
 3. Quantity  6. Remarks
Example
1 2 3 4 5 6 Note:
 “F” is face size
Concealed
FBR 900X500mm 50 nos. Ral 9010 Damper  “N” is actual neck size
type fixing  “C” is the frame

HAWA INDUSTRIAL
GRILLES & REGISTRES
FRESH AIR GRILLE & REGISTER FAG

The Fresh air grille & Registers are the same as the single deflection fixed blade and should be with aluminum
washable filter.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Blades : Aerofoil blades from aluminum profiles
 Blade spacing:20mm as standards
 Filter Frame: 1 mm thick aluminum sheet.
Blades mounting  Filter Media: Aluminum Mesh.

Description:
 Deflection blades are fixed rigidly to the frame
at an angle of 45° to the horizontal plane.
 Removable 12 mm thick aluminum washable
filter is placed at the back of the grille.
 Interlocked corners and mechanically stacked to
FAG FAR
form a rigid frame.
Standard Color:  Filter can be removed easily by opening the
As standard the grille is supplied in either off white RAL grille frame.
9010 or white RAL 9016 polyester powder paint.  Extruded aluminum blades with aero-foil cross
Standard Sizes Available: section for minimum turbulence.
 Auxiliary frames available on request for neat
Any combination of length and width:
and separable mounting in plaster and other wall
Dimensions materials.
Neck Size (N) Face Size (F) C  Opposed blade damper (OBD) operator for the
Inch mm Inch mm mm mm register is easily adjusted through face with a
screw driver.
4 100 9 225 30 40
 Borders are one piece construction in size
6 150 13.5 337 30 40
through 1200 mm x 1200 mm, for smooth
8 200 17 425 30 40 appearance and easy installation.
10 250 20.5 512 30 40  If the grill width more than 500mm, a mullion
12 300 25 625 30 40 will be fixed at the center and for widths of one
14 350 29 725 30 40 meter and above, the number of mullions will be
16 400 31 775 30 40 two or more.
18 450 33 825 35 40  Fixing methods are same as all the grilles either
20 500 36.5 912 35 40 by screws or concealed clips.
24 600 40.5 1012 35 40
Option:
A 1 cm clearance is deducted from your order neck size.
Ordering Data:  Frame width is available in (30 & 20mm)
 Colors available upon request
Specify
 4. Type of fixing  Foam gasket on the back of the frame provided
 1. HAWA type and model
on request.
 2. Nominal size - L x W  5. Surface finish
 3. Quantity  6. Remarks
Note:
Example  “F” is face size
1 2 3 4 5 6  “N” is actual neck size
Concealed  “C” is the frame
FAR 900X500mm 50 nos. Ral 9010 Damper
type fixing

HAWA INDUSTRIAL
GRILLES & REGISTRES DCG/DCR
DECORATIVE GRILLES & REGISTERS
HAWA decorative grilles are now used for more than just
comfort conditioning; they are also used to enhance the
aesthetics of the environment in which they are installed.
HAWA decorative Grilles are used frequently in Majlis,
Atriums, and other spaces. Our grilles are guaranteed to
have unparalleled beauty and brilliance backed by ideal
technology and are created for contemporary interior
layouts.

Construction:
 Frame: High quality extruded aluminum profile
with 25mm flange width as standard and 12,
30mm flange widths as optional.
 Core: Core is made up of aluminum sheet,
machined to the desired design patterns required
by the customer.
 Damper frame and blades: High quality
extruded aluminum profiles with black matt
finish.

Description:
 The frame is made of rigid, high-quality
extruded aluminum with a profiled construction
that resists corrosion.
 The decorative grille's core, which is typically
pressed aluminum sheet, will be its beating heart.
The required designs are cut using cutting-edge
laser technology.
 The decorative grilles are rigidly fixed with
opposed blade damper by grippers. Damper blade
is operated from the face opening.
A 1 cm clearance is deducted from your order neck size. Free area mainly depends on the design pattern
of core / grille. The same can be provided on
request.
Ordering Data:  Fixing methods are same as our normal grilles
Specify either by screws or concealed clips.
 4. Type of fixing  These decorative grilles can be fixed on ceilings
 1. Face Design
or wall.
 2. Nominal size - L x W  5. Surface finish
 3. Quantity  6. Remarks Option:
 Colors available upon request
Example
 Design available upon request
1 2 3 4 5 6
FACE
 Foam gasket on the back of the frame provided
1700x900 2 Ral 9010 Type ‘S’ fixing - on request.
Design

HAWA INDUSTRIAL
GRILLES & REGISTRES
GRILLE & REGISTER FIXING DETAILS

Screw Fixing Concealed Fixing

MULLION ARRANGEMENT:

L x W = Nominal size = Duct size

If W or L ≤ 500 mm → without mullion
W or L > 500 mm →1 mullion
W or L > 1000 mm →2 mullions

• Mullion: Aluminum profiled U-channel.

• If the length of the grille is above 500 mm, horizontal aerofoil blades are connected through a mullion,
fixed at the center of the grille for stability.
• For grilles of length 1000 mm and above, two mullions will be connected vertically at equidistant

HAWA INDUSTRIAL
GRILLES & REGISTRES
ENGINEERING AND PERFOMANCE DATA
DOUBLE DEFLECTION GRILLES AND REGISTERS
Rating
GRILLES with 0° and 45°Deflection
AND REGISTERS

• Face velocity is measured in m/sec.

• Total pressure loss is in mm of H2O & Area factor in square meter.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
GRILLES & REGISTRES

DOUBLE DEFLECTION GRILLES AND REGISTERS

Rating
GRILLES with 0° and 45°Deflection
AND REGISTERS

• Face velocity is measured in m/sec.

• Total pressure loss is in mm of H2O & Area factor in square meter.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
GRILLES & REGISTRES

DOUBLE DEFLECTION GRILLES AND REGISTERS

Rating
GRILLES with 0° and 45°Deflection
AND REGISTERS
a50x350 400 X 400 500x 350 a50x 450
Listed 400x300 500x 300 60'.lx 300 500 X 400
Size in 500 X 250 600x 250 700x 250 800 X 250
CFM mmxmm 60'.) X 200 750x200 90'.lx 200 1000 X 20'.)
M1/aec 900 X 150 1200 X 150
An!a tactor O.C633 0.0529 0.0827 0.072 0.09.26 0.0853 0. 1069 0.097
Def\ection rl' 45° QA 45° o· er oo 45°
500 Face vel. 3.73 a. 7 2.26 3.28 2 .a6 2.77 2.21 2.43
P, mm H,O 0.48 1.02 0.28 0.4 5 0.20 0.31 015 0.23
0.2962 Throw in(M) 7.3-10.9 5.8-9. 1 6.7-10.7 5.5·9 1 9.5- 10.4 5.2-9. 1 6.1-10.1 4.9-8.8
N.C <15 16 <15 < 15 <15 < 15 <15 < 15
600 Face vel. 4.47 5-36 3.43 3.94 2.95 3.32 2.65 2.92
P, mm H,O 0.71 1.45 0.41 0.63 0 .31 0.43 0.23 0.31
0.2834 Throwin(M) 8.2-11.9 6.4-10.1 7.~11 .6 6.4-10.1 7.3-11 .3 6. 1- 10. 1 7.0-10.7 6.1 -9.8
N.C 16 20 <15 18 <15 15 <15 < 15
700 Face vel. 5.22 625 4.0 0.59 3.04 3.89 3.Cl9 3.4
P, mm H,O 0.96 1.98 0.::6 0.86 0.0 1 0.56 0.31 0.43
0.3907 Throwin(M) 8.S-12..8 7,3- 0.9 8.5-12.5 7.0-11.0 8.5-12.2 7.0- 10.9 8.2- 11.9 6.7- 10.7
N.C 22 26 19 23 16 20 15 19
800 Face vel 5.97 7.14 4.57 5.25 3.93 4.43 3.53 3.89
P, mm H,O 1.27 2..59 0.71 1. 14 0.53 0 .74 0.38 0 .56
0.3778 Throwin(M) 9.S-13.4 82-11 .9 9.5- 13. l 7.9-10.6 9.5-13. 1 7.9-11.6 9. 1-12.5 7.~ 11.3
N.C 3'.) 32 26 28 21 25 20 24
900 Face vel 6.71 8.03 5. 4 5.9 4.02 4.99 3.98 4.38
P, mm H,O 1.60 325 0.91 1.45 0.68 0.94 0.08 0.71
0.425 Throwin(M) 10.1- 14.6 8..5-12.5 10. 1- 14.3 8.5-12.2 10.1-140 8.5-1 2.2 9.8-13.7 8.2-12 2
N.C 33 36 30 33 25 30 24 29
1000 Face vel 7.44 8.92 5.69 6.55 4.92 5.55 4.05 4 .86
P, mm H,O 1.98 a.at l.11 1.78 0.84 1.17 0.61 0.86
0.472 Throwin(M) 10.7-15 9. J.13 10.4-15 9. 1-13.1 10.4-14.6 9. 1-13..1 10.1-10.3 9.2-13. 1
N.C 37 llO 34 36 30 33 29 32
1100 Face vel 8.1 8 9..81 6.25 7.21 5.01 6. 11 4.89 5 .35
PmmHO
• 2
2.39 488 t.35 2.16 t.02 1.42 074 t.07
0.519 Throwin(M) 10.9-16 98-14 10.7- 15 9.8-14 10.7-15.0 9.8- 14 0.4-1 4.9 9.S- 14
N.C 40 as 3,6 GO 33 36 32 35
1200 Face vel 6.83 7.87 5.91 6.67 5..35 5.84
P, mm H,O t.eo 2.54 1.22 1.68 1.0 1.24
0.567 Throwin(M) 11.3-16 10.4- 15 11.3-15.9 10.4- 14.9 11-15.2 10-14 .8
N.C 38 a3 3,6 40 35 39
1400 Face vel 7.96 9. 18 6 .88 7.77 6.23 6.81
P, mm H20 2.18 3.51 t.65 2.28 1.19 1.73
0.661 Throwin(M) 12.2-17 11-15.5 12.2-168 109-15.2 11.~16.2 10.4-15
N.C 44 G9 41 40 40 43

• Face velocity is measured in m/sec.

• Total pressure loss is in mm of H2O & Area factor in square meter.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
GRILLES & REGISTRES

DOUBLE DEFLECTION GRILLES AND REGISTERS

Rating
GRILLES with 0° and 45°Deflection
AND REGISTERS

• Face velocity is measured in m/sec.

• Total pressure loss is in mm of H2O & Area factor in square meter.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
GRILLES & REGISTRES

SINGLE DEFLECTION GRILLES AND REGISTERS

Rating
GRILLES with 0° Deflection
AND REGISTERS

• Face velocity is measured in m/sec.

• PS: Static pressure loss in mm of H2O
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
GRILLES & REGISTRES

SINGLE DEFLECTION GRILLES AND REGISTERS

Rating
GRILLES with 45° Deflection
AND REGISTERS

• Face velocity is measured in m/sec.

• PS: Static pressure loss in mm of H2O
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
GRILLES & REGISTRES

SINGLE DEFLECTION GRLLE & REGISTER

Fixed Horizontal Blades at 45°Deflection

Blades At 45°Deflection

• Face velocity is measured in m/sec.

• PS: Static pressure loss in mm of H2O
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
GRILLES & REGISTRES ECG

EGG CRATE GRILLE

Egg crate grille is designed to meet the commercial & industrial need for low resistance, high to medium air volume
return or exhaust grille. These grilles are either ceiling mounted or wall mounted air terminal devices.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Egg Crate Core: Aluminum Grid
12.5mm x 12.5mm x 12.5mm

Description:
Blades mounting  Frame from high quality extruded aluminum
profiles with advantages of corrosion resistance
and rigidity.
 Rigid construction provides noiseless
performance.
 Designed for exhaust and return applications for
conditioned space.
 Completely Removable or Hinged Cores for Ease
ECG of Access and Maintenance.
 High Free Area: 90% Offering Lowest Sound
Option: And Pressure Levels
 Frame width is available in (30 & 20mm)  12.7x12.7mm Square Lattice Core.
 Insect screen  Grille Form Similar In Appearance To Many
 Colors available upon request Lighting Fixtures.
 Foam gasket on the back of the frame provided on
request.

Standard Color:
As standard the grille is supplied in either off white RAL
9010 or white RAL 9016 polyester powder paint.
Standard Sizes Available:
 Available in square and rectangular sizes
 Non standards sizes available as option.

A 1 cm clearance is deducted from your order neck size.

Width in mm 150 225 300 375 450 525 600

Height in mm 150 225 300 375 450 525 600
Ordering Data:
Specify
 1. HAWA type and model  4. Type of fixing
 2. Nominal size - L x W  5. Surface finish
 3. Quantity  6. Remarks
Example
1 2 3 4 5 6
Concealed
ECG 300X300mm 10 nos. Ral 9010 -
type fixing

HAWA INDUSTRIAL
GRILLES & REGISTRES ECR

EGG CRATE REGISTER

Egg crate register is designed to meet the commercial & industrial need for low resistance, high to medium air
volume return or exhaust grille. These grilles are either ceiling mounted or wall mounted air terminal devices.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Egg Crate Core: Aluminum Grid
12.5mm x 12.5mm x 12.5mm
 Damper frame: Aluminum profiles with natural
aluminum finish.
 Blades: Black matt finish as option.

Description:

 Frame from high quality extruded aluminum

profiles with advantages of corrosion resistance
and rigidity.
 Rigid construction provides noiseless
performance.
 Grilles fixed with opposed blade damper for
ECG controlling exhaust air flow.
 Completely Removable or Hinged Cores for Ease
Option: of Access and Maintenance.
 Frame width is available in (30 & 20mm)  High Free Area: 90% Offering Lowest Sound
 Insect screen And Pressure Levels
 Colors available upon request  12.7x12.7mm Square Lattice Core.
 Foam gasket on the back of the frame provided on  Grille Form Similar In Appearance To Many
request. Lighting Fixtures
 Damper blades can be screw operated from the
Standard Color: face opening.
As standard the grille is supplied in either off white RAL
9010 or white RAL 9016 polyester powder paint.
Standard Sizes Available:
 Available in square and rectangular sizes
 Non standards sizes available as option.
A 1 cm clearance is deducted from your order neck size.

Width in mm 150 225 300 375 450 525 600

Height in mm 150 225 300 375 450 525 600
Ordering Data:
Specify
 1. HAWA type and model  4. Type of fixing
 2. Nominal size - L x W  5. Surface finish
 3. Quantity  6. Remarks
Example
1 2 3 4 5 6
Concealed
ECR 300X300mm 10 nos. Ral 9010 Damper
type fixing

HAWA INDUSTRIAL
GRILLES & REGISTRES
EGG CRATE FIXING DETAILS

Screw Fixing

Concealed Fixing

ENGINEERING AND PERFOMANCE

DATA

• Air flow data for non-standards sizes can be interpolated from the above data.

HAWA INDUSTRIAL
GRILLES & REGISTRES DG-SF/DG-DF

DOOR GRILLES –SINGLE & DOUBLE FRAME

Our Door Grille Offers the Best Solution for A Completely Sight Proof Design. Designed For Installation In Doors,
Walls Or Partition Where Constant Passage Of Air And Non-Vision Is Desired. V Shape Blades Not Only Block Vision
But Also Provide Stiffness.

Construction:
 Frame: High quality extruded aluminum profiles
with 30 mm flange with as standard.
 Blade: High quality extruded aluminum profiles.
 Blade pitch: 20mm

Description:
 Constructed As Inverted V Shape Blades Rigidly
Assembled One Above The Other To Avoid
Vibration And Corrosion.
 Blades are spaced At a Distance Of 18-20mm.
 Provided With A Counter Frame For Fixing On
Both Sides Of The Door.
 Structure Provides Around 55% Free Area For
Air Transmission.
 Used In Facilities Such As Offices, Hospitals,
Schools And Toilets For Transfer Of Air From One
Room To Another Room.
 Lighting Fixtures
 For FG-DF, Frame is fabricated to suit door
thickness of 30 mm to 60 mm.

Standard Color: Option:

As standard the grille is supplied in either off white RAL  Frame width is available in (30 & 20mm)
9010 or white RAL 9016 polyester powder paint.  Insect screen
Standard Sizes Available:  Colors available upon request
 Availa  Foam gasket on the back of the frame provided
ble in square and rectangular sizes on request.
 Non
standards sizes available as option.
W= width in mm 150 200 250 300 350 400 450 500 600 Fixing Details
D=depth in mm 150 200 250 300 350 400 450 500 600
A 1 cm clearance is deducted from your order neck size.
Ordering Data:
Specify
 1. HAWA type and model  4. Frame
 2. Nominal size - L x W  5. Surface finish
 3. Quantity  6. Remarks
Example
1 2 3 4 5 6
30 mm flange
DG-DF 150X150 10 Double Frame RAL 9010
20 mm blade space With single frame With double frame

HAWA INDUSTRIAL
GRILLES & REGISTRES DG-SF/DG-DF

ENGINEERING AND PERFOMANCE

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

HAWA INDUSTRIAL
 LINEAR BAR GRILLES & REGISTERS SDLBG
SINGLE DEFLECTION LINEAR BAR GRILLE
Linear Bar Grille offers an architectural appear to designers while providing engineers with flexibility and reliability.
These Grilles are an excellent choice for applications where they are exposed and accessible to heavy traffic. These are
recommended for supply and return air duct. This type of outlets can be installed directly in sidewalls or in plenum box.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Face bars: High quality aluminum profiles of 0°,
15°-1 way throw and 15°-2 ways throw.
Blades mounting  Bar spacing: 12 mm as standard 6 mm as option.
 Grille width: 50 mm to 300 mm with increments
of 50 mm.

Description:
 Interlocked into heavy gauge cross bars to
produce straight rigid core sections.
 Frame and face bars from high quality extruded
aluminum profiled construction with the
advantages of corrosion resistance and rigidity
 Multiple angles of deflection. (0º, 15º and 30º).
 For perfect, continuous line usage on a large
variety of applications, joining strips are provided
in proper lengths with no extra cost.
 Horizontal face bars with 0°, 15°-1 way throw
SDLBG and 15°-2 way throw are fixed rigidly to the frame
Standard Color: with 8 mm pipes.
 As standard the grille is supplied in either off white Foam Gasket provided all around the frame, to
RAL 9010 Sizes
or white RAL 9016 polyester powder paint. prevent leakage of air.
Standards Available:
 For perfect unbroken appearance of continuous
runs, alignment strips are provided with no
 Grilles are available with 1 meter length as standard. additional cost.
 Length from 0.2 meter to 5.8 meter is available as  Total structure is manufactured by mechanical
single piece. assembly, assuring rigidity and to maintain
 Non-standard sizes available as option. straight line appearance.
 Supplied with C-clamps for concealed fixing.
Width in mm 50 100 150 200 250 300
A 1 cm clearance is deducted from your order neck size.
Ordering Data:
Specify
 1. HAWA type and model  5. Quantity
 2. Nominal size - L x W  6. Type of fixing Option:
 3. Face bar(0°, 15° -way, 15°-2 way)  7. Surface finish
 4. End flange details  Other colors available upon request.
 8. Remarks
 Plenum box - insulated or non-insulated.
Example  Equalizing grid.
 Insect screen.
1 2 3 4 5 6 7 8
 Mitered corners are available for continuous bar
Concealed
SDLBG 1000X250mm 15°-2 way Open End 10 nos. Ral 9010 - grille around ceiling edges.
type fixing  Foam gasket on the back of the frame provided
on request.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS SDLBR
SINGLE DEFLECTION LINEAR BAR REGISTER
Linear Bar Register offers an architectural appear to designers while providing engineers with flexibility and
reliability. These Grilles are an excellent choice for applications where they are exposed and accessible to heavy
traffic. These are recommended for supply and return air duct. This type of outlets can be installed directly in
sidewalls or in plenum box.
Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Face bars: High quality aluminum profiles of 0°,
15°-1 way throw and 15°-2 ways throw.
 Bar spacing: 12 mm as standard 6 mm as option.
Blades mounting  Grille width: 50 mm to 300 mm with increments
of 50 mm.
 Damper frame: Aluminum profiles with natural
aluminum finish.
 Blades: Black matt finish as option.

Description:
 Interlocked into heavy gauge cross bars to
produce straight rigid core sections.
 Frame and face bars from high quality extruded
aluminum profiled construction with the
advantages of corrosion resistance and rigidity
 Multiple angles of deflection. (0º, 15º and 30º).
 For perfect, continuous line usage on a large
variety of applications, joining strips are provided
SDLBR in proper lengths with no extra cost.
 Horizontal face bars with 0°, 15°-1 way throw
Standard Color: and 15°-2 way throw are fixed rigidly to the frame
 As standard the grille is supplied in either off white with 8 mm pipes. Foam Gasket provided all
RAL 9010 or white RAL 9016 polyester powder paint. around the frame, to prevent leakage of air.
Standards Sizes Available:  For perfect unbroken appearance of continuous
runs, alignment strips are provided with no
 Register are available with 1 meter length as standard. additional cost.
 Length from 0.2 meter to 5.8 meter is available as  Total structure is manufactured by mechanical
single piece. assembly, assuring rigidity and to maintain
 Non-standard sizes available as option. straight line appearance.
 Grilles are fixed rigidly with opposed blade
Width in mm 50 100 150 200 250 300 damper by grippers. This ensures positive control
A 1 cm clearance is deducted from your order neck size. over the air stream. Damper blades can be screw
operated from the face opening.
Ordering Data:  Supplied with C-clamps for concealed fixing.
Specify
 1. HAWA type and model  5. Quantity Option:
 2. Nominal size - L x W  6. Type of fixing
 Other colors available upon request.
 3. Face bar(0°, 15° -way, 15°-2 way)  7. Surface finish
 Plenum box - insulated or non-insulated.
 4. End flange details  8. Remarks  Equalizing grid.
Example  Insect screen.
1 2 3 4 5 6 7 8  Mitered corners are available for continuous bar
grille around ceiling edges.
Concealed
SDLBR 1000X250mm 15°-2 way Open End 10 nos. Ral 9010 Damper  Foam gasket on the back of the frame provided
type fixing on request.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS DDLBG
DOUBLE DEFLECTION LINEAR BAR GRILLE
Linear Bar Grille offers an architectural appear to designers while providing engineers with flexibility and
reliability. These Grilles are an excellent choice for applications where they are exposed and accessible to heavy
traffic. These are recommended for supply and return air duct. This type of outlets can be installed directly in
sidewalls or in plenum box.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Face bars: High quality aluminum profiles of 0°,
Blades mounting 15°-1 way throw and 15°-2 ways throw.
 Bar spacing: 12 mm as standard 6 mm as option.
 Grille width: 50 mm to 300 mm with increments
of 50 mm.

Description:
 Interlocked into heavy gauge cross bars to
produce straight rigid core sections.
 Frame and face bars are of high quality extruded
aluminum profiled construction with the
advantages of corrosion resistance and rigidity.
 Face bars are made of aluminum, with 6.4mm
wide bars pressed into a notched aluminum
retaining bar on 12.5mm centers.
 Horizontal face bars with 0°, 15°-1 way throw
and 15°-2 way throw are fixed rigidly to the frame
with 8 mm pipes.
DDLBG  Vertical aluminum aerofoil blades are fixed at
Standard Color: the rear side of the frame by nylon bushes.
 As standard the grille is supplied in either off white  These blades can be adjusted manually and
RAL 9010 orSizes
Standards white RAL 9016 polyester powder paint.
Available: individually in the vertical plane to obtain
optimum air distribution.
 Grilles are available with 1 meter length as standard.  Multiple angles of deflection. (0º, 15º and 30º).
 Length from 0.2 meter to 5.8 meter is available as  For perfect, continuous line usage on a large
single piece. variety of applications, joining strips are provided
in proper lengths with no extra cost.
 Non-standard sizes available as option.
 Foam Gasket provided all around the frame, to
prevent leakage of air.
Width in mm 50 100 150 200 250 300  Total structure is manufactured by mechanical
A 1 cm clearance is deducted from your order neck size. assembly, assuring rigidity and to maintain
Ordering Data: straight line appearance.
 Supplied with C-clamps
Specify
for concealed fixing.
 1. HAWA type and model  5. Quantity Option:
 2. Nominal size - L x W  6. Type of fixing
 3. Face bar(0°, 15° -way, 15°-2 way)  7. Surface finish  Other colors available upon request.
 4. End flange details  Plenum box - insulated or non-insulated.
 8. Remarks
 Equalizing grid.
Example  Insect screen.
1 2 3 4 5 6 7 8  Mitered corners are available for continuous bar
Concealed grille around ceiling edges.
DDLBG 1000X250mm 15°-2 way Open End 10 nos. Ral 9010 -  Foam gasket on the back of the frame provided
type fixing
on request.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS DDLBR
DOUBLE DEFLECTION LINEAR BAR REGISTER
Linear Bar Register offers an architectural appear to designers while providing engineers with flexibility and
reliability. These Grilles are an excellent choice for applications where they are exposed and accessible to heavy
traffic. These are recommended for supply and return air duct. This type of outlets can be installed directly in
sidewalls or in plenum box.
Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Face bars: High quality aluminum profiles of 0°,
15°-1 way throw and 15°-2 ways throw.
 Bar spacing: 12 mm as standard 6 mm as option.
 Grille width: 50 mm to 300 mm with increments
Blades mounting of 50 mm.

Description:
 Interlocked into heavy gauge cross bars to
produce straight rigid core sections.
 Face bars are made of aluminum, with 6.4mm
wide bars pressed into a notched aluminum
retaining bar on 12.5mm centers.
 Horizontal face bars with 0°, 15°-1 way throw
and 15°-2 way throw are fixed rigidly to the frame
DDLBR with 8 mm pipes.
 Vertical aluminum aerofoil blades are fixed at
Standard Color: the rear side of the frame by nylon bushes.
 These blades can be adjusted manually and
 As standard the grille is supplied in either off white
individually in the vertical plane to obtain
RAL 9010 or white RAL 9016 polyester powder paint.
optimum air distribution.
Standards Sizes Available:  Multiple angles of deflection. (0º, 15º and 30º).
 Grilles are available with 1 meter length as standard.  For perfect, continuous line usage on a large
 Length from 0.2 meter to 5.8 meter is available as variety of applications, joining strips are provided
single piece. in proper lengths with no extra cost.
 Non-standard sizes available as option.  Foam Gasket provided all around the frame, to
prevent leakage of air.
 Total structure is manufactured by mechanical
Width in mm 50 100 150 200 250 300 assembly, assuring rigidity and to maintain
straight line appearance.
A 1 cm clearance is deducted from your order neck size.  Supplied with C-clamps for concealed fixing.
 Grilles are fixed rigidly with an opposed blade
Ordering Data: damper by grippers to ensure positive control
over the air stream.
Specify  Damper blades, painted matt black, are screw
 1. HAWA type and model  5. Quantity operated from the face opening of the grille.
 2. Nominal size - L x W  6. Type of fixing
 3. Face bar(0°, 15° -way, 15°-2 way)  7. Surface finish Option:
 4. End flange details  8. Remarks  Other colors available upon request.
 Plenum box - insulated or non-insulated.
Example  Equalizing grid.
1 2 3 4 5 6 7 8  Insect screen.
Concealed  Mitered corners are available for continuous bar
DDLBR 1000X250mm 15°-2 way Open End 10 nos. Ral 9010 Damper grille around ceiling edges.
type fixing
 Foam gasket on the back of the frame provided
on request.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS DDLBG-C/ DDLBR-C
DOUBLE DEFLECTION LINEAR BAR GRILLE& REGISTER CURVED
Specializing in convex, concave and flat face curved bar grilles & registers, we are able to facilitate architectural
design elements and incorporate engineering requirements to produce an aesthetically pleasing and functional
product for any space. Our customized curved bar grilles & registers are available in a variety of sizes, radiuses,
frames, styles, materials and finishes.

Construction:
 Frame : High quality extruded aluminum
 Flange :width 30mm
 Face bars: High quality aluminum profiles of
0°-1 way throw and 15°-2 ways throw.
Blades mounting  Bar spacing: 12 mm as standard 6 mm as option.
 Grille width: 50 mm to 300 mm with increments
of 50 mm.

Description:
 Curved Segments are available for both side wall
curves (CS) and ceiling curves (CP).
 Foam gasket is sealed around the back of the
frame as option to avoid air leakage.
 Curved linear bar grilles are available up to a
length of 3 meter with a minimum radius of
curvature of 1 meter.
 Available without damper. Dampers can be
provided to use in plenum boxes as option.
 For perfect, continuous line usage on a large
variety of applications, joining strips are provided
Standard Color: in proper lengths with no extra cost.
 As standard the grille is supplied in either off white  Horizontal face bars with 0°-1 way throw and
RAL 9010 or white RAL 9016 polyester powder paint.  15º-2 way throw are fixed rigidly to the frame
with 8 mm pipes.
Standards Sizes Available:  Total structure is manufactured by mechanical
 Register are available with 1 meter length as standard. assembly, assuring rigidity and to maintain
 Length from 0.2 meter to 5.8 meter is available as straight line appearance
single piece.  Vertical aluminum aerofoil blades are fixed at
 Non-standard sizes available as option. the rear side of the frame by nylon bushings.
 These blades can be adjusted manually and
Width in mm 50 100 150 200 250 300 individually in the vertical plane to obtain
A 1 cm clearance is deducted from your order neck size. optimum air distribution
 Supplied with C-clamps for concealed fixing.
Ordering Data:
Specify
 1. HAWA type and model  5. Quantity
 2. Nominal size - L x W Option:
 6. Type of fixing
 3. Face bar(0°, 15° -way, 15°-2 way)  7. Surface finish  Other colors available upon request.
 4. End flange details  8. Remark  Plenum box - insulated or non-insulated.
 Equalizing grid.
Example  Insect screen.
1 2 3 4 5 6 7 8
 Mitered corners are available for continuous bar
Concealed
DDLBG-C 1000X250mm 15°-2 way Open End 10 nos. type Ral 9010
Radius of grille around ceiling edges.
fixing
Curvature  Foam gasket on the back of the frame provided
on request.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS
OPTIONAL MITERED CORNERS
Special horizontal mitered
Standard 90° horizontal mitered
corner selection available for
corner available for floor, sill and
floor, sill and ceiling
ceiling applications in 0°,15°-1
applications includes an angle
way throw and 15°-2 way throw
greater than 90° and less than
without damper.
3b) Variable angle (90°- 180°) 180° available in 0°, 15°-1
way throw and 15°-2 way
3a) 90° Horizontal
throw without damper.
Vertical outside mitered Special horizontal mitered
corners are available for wall corner selection available for
application at the junction of floor, sill and ceiling
two outside walls with a applications includes an angle
standard angle of 90°. Available greater than 90° and less than
in 0°, 15°-1 way throw and 15°- 180° available in 0°, 15°-1
3c) 90°Vertical 2 way throw without damper. 3d) 90°Vertical way throw and 15°-2 way
outside insideoutside throw without damper.

BLADE OPTIONS

a) 30° one way b) 15° two way c) 15° one way

FIXING DETAILS

C-Clamp fixing Fixing To the Plenum Box

END FLANGES

With open ends With one side flange With both side flange

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

DOUBLE DEFLECTION LINEAR BAR REGISTER

15°-2
GRILLES AND Way - 12 mm spacing
REGISTERS

• Data based on one meter unit length of the grille with damper in full open position.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

DOUBLE DEFLECTION LINEAR BAR REGISTER

15°-1 Way - 12 mm spacing
GRILLES AND REGISTERS

• Data based on one meter unit length of the grille with damper in full open position.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

DOUBLE DEFLECTION LINEAR BAR REGISTER

GRILLES AND 0° - 12 mm spacing

REGISTERS

• Data based on one meter unit length of the grille with damper in full open position.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

SINGLE DEFLECTION LINEAR BAR REGISTER

GRILLES 15°-2
AND REGISTERS
Way - 12 mm spacing

• Data based on one meter unit length of the grille.

• PS: Static pressure loss is in mm of H2O.
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

SINGLE DEFLECTION LINEAR BAR REGISTER

15°-1 Way - 12 mm spacing
GRILLES AND REGISTERS

• Data based on one meter unit length of the grille.

• PS: Static pressure loss is in mm of H2O.
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

SINGLE DEFLECTION LINEAR BAR REGISTER

0° - REGISTERS
GRILLES AND 12 mm spacing

• Data based on one meter unit length of the grille.

• PS: Static pressure loss is in mm of H20.
• NC based on a room attenuation of 10 dB.

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

DOUBLE DEFLECTION LINEAR BAR REGISTER

15°-2
GRILLES ANDWay - 6 mm spacing
REGISTERS

• Data based on one meter unit length of the grille with damper in full open position.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 dB

HAWA INDUSTRIAL
LINEAR BAR GRILLES & REGISTERS

SINGLE DEFLECTION LINEAR BAR REGISTER

15°-2 Way - 6 mm spacing
GRILLES AND REGISTERS

• Data based on one meter unit length of the grille with damper in full open position.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 dB

HAWA INDUSTRIAL
 LINEAR SLOT DIFFUSER
RECTANGULAR DUCT & FITTING
OUR PRODUCT

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS SLSD
SUPPLY LINEAR SLOT DIFFUSER
Linear Slot Diffusers have been designed to satisfy architectural concepts that require continuous length
applications without compromising air distribution performance and low pressure drops at different air passage
velocities. Our linear slot diffusers are specially designed to provide supply or return air in heating, cooling or
ventilating systems.

Construction:
 Frame & Blades: High quality extruded
aluminum profiles
 Flange:31mm width & 45mm height
 Deflector blades: 21 mm high aluminum
extruded
 Damper: Hit and Miss Damper
 Slot width: 16mm,20mm & 25mm
 Number of slot available:1,2,3,4,5,6,7,8
 Length: Up to 6m available in a single piece.

Description:
 Low Leakage Frame styles.
 Air distribution can be changed vertically or
horizontally by means of deflection blades
without changing the air flow rate. These blades
can be fully adjusted from face opening.
 Available in 3 different slot widths, from 1
through 8 slots, linear slot diffusers permit
complete control of flow rate without disturbing
the selected air pattern.
SLSD  Single or multiple slot arrangement will provide
full 180° adjustable air diffusing patterns
 Air volume can be controlled by adjusting the hit
and miss damper attached to the top side of the
Standard Color: slot diffuser.
 As standard the grille is supplied in either off white  For perfect, continuous line usage on a large
RAL 9010 or white RAL 9016 polyester powder paint. variety of applications, joining strips are provided
in proper lengths with no extra cost.
A 1 cm clearance is deducted from your order neck size.  Positive alignment of adjacent sections can be
made by using alignment strips.
 The volume damper is designed in a unique way
Ordering Data: that it can be used as an equalizing grid.
Specify 
 1. HAWA type and model  4. Type of fixing Option:
 2. Nominal size - L x Slot number  5. Surface finish  Other colors available upon request.
 3. Quantity  6. Remarks  Plenum box - insulated or non-insulated.
 Equalizing grid.
 Insect screen.
 Mitered corners are available for continuous bar
grille around ceiling edges.
 Foam gasket on the back of the frame provided
on request.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS RLSD
RETURN LINEAR SLOT DIFFUSER
Linear Slot Diffusers have been designed to satisfy architectural concepts that require continuous length
applications without compromising air distribution performance and low pressure drops at different air passage
velocities. Our linear slot diffusers are specially designed to provide supply or return air in heating, cooling or
ventilating systems.

Construction:
 Frame & Blades: High quality extruded
aluminum profiles
 Flange: 31mm width & 45mm height
 Deflector blades: 21 mm high aluminum
extruded
 Damper: Hit and Miss Damper
 Slot width: 16mm,20mm & 25mm
 Number of slot available: 1,2,3,4,5,6,7,8
 Length: Up to 6m available in a single piece.

Description:
 Low Leakage Frame styles.
 Air distribution can be changed vertically or
horizontally by means of deflection blades
without changing the air flow rate. These blades
can be fully adjusted from face opening.
 Available in 3 different slot widths, from 1
through 8 slots, linear slot diffusers permit
complete control of flow rate without disturbing
the selected air pattern.
 Single or multiple slot arrangement will provide
full 180° adjustable air diffusing patterns
RLSD  Air volume can be controlled by adjusting the hit
and miss damper attached to the top side of the
slot diffuser.
 For perfect, continuous line usage on a large
Standard Color: variety of applications, joining strips are provided
 As standard the grille is supplied in either off white in proper lengths with no extra cost.
RAL 9010 or white RAL 9016 polyester powder paint.  Positive alignment of adjacent sections can be
made by using alignment strips.
A 1 cm clearance is deducted from your order neck size.

Ordering Data:
Specify Option:
 1. HAWA type and model  4. Type of fixing  Other colors available upon request.
 2. Nominal size - L x Slot number  5. Surface finish  Plenum box - insulated or non-insulated.
 3. Quantity  6. Remarks  Equalizing grid.
 Insect screen.
Example  Mitered corners are available for continuous bar
1 2 3 4 5 6 grille around ceiling edges.
 Foam gasket on the back of the frame provided
RLSD 1000x3 slot 10 Type 'C' fixing Ral 9010 - on request.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS SLSD-C/RLSD-C
CURVED SUPPLY & RETURN LINEAR SLOT
Curved Linear Slot Diffusers used in interior of large offices, hospitals, public area of hotels, malls for supply and
DIFFUSER
return air for uncluttered looking wall and ceiling.

Construction:
 Frame & Blades: High quality extruded
aluminum profiles
 Flange: 31mm width & 45mm height
 Deflector blades: 21 mm high aluminum
extruded
 Damper: Hit and Miss Damper
 Slot width: 16mm,20mm & 25mm
 Number of slot available: 1,2,3,4,5,6,7,8
 Length: Up to 3m available in a single piece.

Description:
 Low Leakage Frame styles.
 Available in 3 different slot widths, from 1
through 8 slots, linear slot diffusers permit
complete control of flow rate without disturbing
the selected air pattern.
 Single or multiple slot arrangement will provide
full 180° adjustable air diffusing patterns
 Air volume can be controlled by adjusting the hit
and miss damper attached to the top side of the
slot diffuser.
 Hit and miss damper will be fixed rigidly at the
rear side of the diffuser as option
 For perfect, continuous line usage on a large
variety of applications, joining strips are provided
in proper lengths with no extra cost.
 Positive alignment of adjacent sections can be
made by using alignment strips.
 The volume damper is designed in a unique way
SLSD-C/RLSD-C that it can be used as an equalizing grid.
 Supply and return air curved linear slot diffuser
Standard Color: are available up to a length of 3meters with a
 As standard the grille is supplied in either off white minimum radius of curvature of 1 meter.
RAL 9010 or white RAL 9016 polyester powder paint.

A 1 cm clearance is deducted from your order neck size. Option:

 Other colors available upon request.
Ordering Data:  Plenum box - insulated or non-insulated.
Specify  Equalizing grid.
 1. HAWA type and model  4. Type of fixing  Insect screen.
 2. Nominal size - L x Slot number  5. Surface finish  Mitered corners are available for continuous bar
 3. Quantity  6. Remarks grille around ceiling edges.
 Foam gasket on the back of the frame provided
Example on request.
1 2 3 4 5 6
SLSD-C 1000x3 slot 10 Type 'C' fixing Ral 9010 Radius

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS
SLOT DIFFUSER DIMENSION
16 mm slot opening
N of slot 1 2 3 4 5
Neck size in mm 33 66 100 134 166
Duct size in mm 49 76 110 145 176
Over all size 83 116 150 184 216

20 mm slot opening
N of slot 1 2 3 4 5
Neck size in mm 39 77 115 155 192
Duct size in mm 53 87 125 165 202
Over all size 89 127 165 205 242
25 mm slot opening
N of slot 1 2 3 4 5
Neck size in mm 44 87 130 175 215
Duct size in mm 55 97 140 185 225
Over all size 94 137 180 225 265

OPTIONAL MITERED CORNERS

Standard 90° horizontal Special horizontal

mitered corners available mitered corners selection
for floor, sill and ceiling available for floor still and
applications. ceiling application
includes an angle greater
than 90° and less than
180°.
90°Mitered corner Variable mitered corner

Vertical outside mitered Vertical inside mitered

corners are available for corners are available for
wall application at the wall application at the
junction of two outside junction of two inside
walls with a standard wall with a standard
angle of 90°. angle 90°.

Side wall-outside corner Side wall-inside corner

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS
Flange models

With Open Ends With Open Side Flange With Both Side Flange

With One Side End Cap With Both Side End Cap

Fixing Details

C-Clamp fixing Fixing To the Plenum Box

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

16 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

16 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

20 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

20 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

25 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS

Supply Linear Slot Diffuser

25 mm Slot Width

• Data based on one meter length of the diffuser with damper fully opened.
• Face velocity is measured in m/sec.
• PS: Static pressure loss is in mm of H2O.
• Area factor in square meters.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
LINEAR SLOT DIFFUSERS SFBD/RFBD
FLOWBAR SLOT DIFFUSER
Flow Bar systems satisfy both the architect's and the
engineer's requirements for air distribution system that will
maintain optimum room air conditions. The HAWA Flow
Bar linear system is a continuous slot system which allows
the air distribution while being fully integrated within the
ceiling system and its components.

Construction:
 Frame: High quality extruded aluminum profile
of 1.2mm thickness.
 Deflector: Heavy duty adjustable Aluminum
channels.
Standard Color:
 U-Channel: Press to fit aluminum profile to
 As standard the grille is supplied in either off white guide deflector.
RAL 9010 or white RAL 9016 polyester powder paint.  Slot opening: 25mm, 38mm and 50mm
A 1 cm clearance is deducted from your order neck size.
Ordering Data: Description:
Specify  Designed ceiling mounted applications. The
 1. HAWA type and model view of a black opening into the ceiling gives a
 4. Type of fixing
high-class finish to the building interiors.
 2. Nominal size - L x Slot width  5. Surface finish
 Can easily handle huge air volumes without
 3. Quantity  6. Remarks
increasing the pressure drop or NC level as
Example compared to regular slot diffuser.
 Equipped with an adjustable flat deflector
1 2 3 4 5 6
profile. It can be moved horizontally on both
SFBD 1000x25 10 Type 'C' fixing Ral 9010 Damper directions (left or right) which help in discharging
air in a horizontal pattern.
 Special side deflectors are provided to channel
Option: airflow smoothly towards the opening thereby
 Special RAL color powder coating is optional reducing the pressure drop significantly and
 Slot opening: 25mm, 50mm subsequently the noise level.
 Curved flow bar diffuser available with a minimum  White frame with black interior makes the finish
radius of curvature of 3 meter. more elegant.
 Mitered corner for ceiling & wall application

DIMENSION AND DETAILS (1 SLOT)

NECK FACE HEIGHT SLOT FLANGE

SLOT SIZE
(N) (F) (H) (W) (FL)
1 SLOT 25 MM 81 119 41 25 47
1 SLOT 38 MM 94 132 41 38 47
1 SLOT 50 MM 107 145 41 51 47
LINEAR SLOT DIFFUSERS SFBD/RFBD

AIR FLOW DIRECTIONS

DIMENSION AND DETAILS (2 SLOTS)

NECK FACE HEIGHT SLOT FLANGE CENTER

SLOT SIZE
(N) (F) (H) (W) (FL) (T)
2 SLOT 25 MM 155 193 41 25 47 49
2 SLOT 38 MM 181 219 41 38 47 49
2 SLOT 50 MM 207 245 41 51 47 49

AIR FLOW DIRECTIONS

LINEAR SLOT DIFFUSERS SFBD-H/RFBD-H

FLOWBAR SLOT DIFFUSER HIDDEN TYPE

DIMENSION AND DETAILS (1 SLOT)

NECK FACE HEIGHT SLOT FLANGE

SLOT SIZE
(N) (F) (H) (W) (FL)
1 SLOT 25 MM 81 87 54 25 30
1 SLOT 38 MM 94 100 54 38 30
1 SLOT 50 MM 107 113 54 51 30

AIR FLOW DIRECTIONS

DIMENSION AND DETAILS (2 SLOTS)

NECK FACE HEIGHT SLOT FLANGE CENTER

SLOT SIZE
(N) (F) (H) (W) (FL) (T)
2 SLOT 25 MM 155 161 54 25 30 49
2 SLOT 38 MM 181 187 54 38 30 49
2 SLOT 50 MM 207 213 54 51 30 49
LINEAR SLOT DIFFUSERS SFBD-H/RFBD-H

AIR FLOW DIRECTIONS

CEILING DIFFUSER

HAWA INDUSTRIAL
CEILING DIFFUSER SCD
SUPPLY CEILING DIFFUSER
HAWA provides a wide range of Ceiling Diffusers to suit the
various requirements of ceiling air distribution. Our ceiling
diffusers provide an aesthetically pleasing solution to air
distribution requirements, regardless of room configuration.
These are specially designed to suit architectural needs to
flush outlets and concealed fixing methods.

Construction:
 Frame and core: High quality extruded
aluminum profile with 33 mm flange width.
 Damper frame and core: High quality extruded
aluminum profile with natural aluminum finish.
 Pressed Frame: High quality aluminum sheets
are pressed to the different sizes of frame molds.
 Pressed frames with fixing holes for cores and
ducts.

Description:
 Can be Square or Rectangle in shape with One,
Two, Three or Four Way Patterns.
Standard Color:  5 “application specific” air distribution patterns
– 1 way, 2 ways opposite, 2 way corner, 3 ways,
 As standard the grille is supplied in either off white and 4 ways.
RAL 9010 or white RAL 9016 polyester powder paint.
 Core can be easily removable and
Standard square air diffuser size: interchangeable to allow for maximum flexibility
 150x150 in installation, maintenance and damper
 225x225 adjustment.
 300x300  Damper is fixed rigidity to the frame by
 375x375 aluminum rivets. Optional spring clips fixing
 450x450 available.
Optional Rectangular Ceiling diffuser:  Discharge air horizontal in one way, either X or
Diffusers are rectangular sizes as per choice. Y directions are per pattern arrangement.
Construction will be same as square diffusers.  Pressed cores and frames gives high
performance than the extruded profiles frames
avoiding the joints at the corners.
 Easy removal of core is necessary to adjust
opposes blade damper operation by screw.

Option:
 Wide selection of sizes and core patterns.
Ordering Data:
 Any RAL color upon request
Specify
 Aluminum equalizing grid
 1. HAWA type and model  4. Type of fixing  Square to round transition
 2. Nominal size - L x L number  5. Surface finish  Plenum box
 3. Quantity  6. Remarks  Foam gasket on the back of the frame provided
Example on request.
 Opposed blades damper, painted black matt, is
1 2 3 4 5 6 screw operated from the face opening of the
SCD 150X150 10 Type 'C' fixing Ral 9010 Damper diffuser after removing the internal core.

HAWA INDUSTRIAL
CEILING DIFFUSER RCD
RETURN CEILING DIFFUSER
HAWA provides a wide range of Ceiling Diffusers to suit
the various requirements of ceiling air distribution. Our
ceiling diffusers provide an aesthetically pleasing
solution to air distribution requirements, regardless of
room configuration.

Construction:
 Frame and core: High quality extruded
aluminum profile with 33 mm flange width.
 Pressed Frame: High quality aluminum sheets
are pressed to the different sizes of frame molds.
 Pressed frames with fixing holes for cores and
ducts.

Description:
 Can be Square or Rectangle in shape with One,
Two, Three or Four Way Patterns.
 5 “application specific” air distribution patterns
Standard Color: – 1 way, 2 ways opposite, 2 way corner, 3 ways,
and 4 ways.
 As standard the grille is supplied in either off white
 Core can be easily removable and
RAL 9010 or white RAL 9016 polyester powder paint. interchangeable to allow for maximum flexibility
Standard square air diffuser size: in installation, maintenance.
 150x150  Pressed cores and frames gives high
 225x225 performance than the extruded profiles frames
 300x300 avoiding the joints at the corners.
 375x375  Easy removal of core is necessary to adjust
 450x450 opposes blade damper operation by screw.
Optional Rectangular Ceiling diffuser:  Return Air use to maintain matched appearance.
Diffusers are rectangular sizes as per choice.
Construction will be same as square diffusers.

Ordering Data:
Specify Option:
 1. HAWA type and model  4. Type of fixing  Wide selection of sizes and core patterns.
 2. Nominal size - L x L number  5. Surface finish  Any RAL color upon request
 3. Quantity  6. Remarks  Aluminum equalizing grid
 Square to round transition
 Plenum box
 Foam gasket on the back of the frame provided
on request.

HAWA INDUSTRIAL
CEILING DIFFUSER
STANDARD SIZES
 Available in square and rectangular sizes.
 Any combination of W x D.

Width in mm 150 225 300 375 450 525 600

Depth in mm 150 225 300 375 450 525 600
FALSE CEILING SIZES

Duct size in mm 150 x 150 225 x 225 300x300 375 x 375 450 x 450 525 x 525
Diffuser Neck Size in mm 145 x 145 220 x 220 295 x 295 370 x 370 445 x 445 520 x 520
Diffuser Face Size in mm 295 x 295 370 x 370 445x445 525 x 525 595 x 595 670 x 670
False ceiling opening size in mm 230x230 305 x 305 380x380 455 x 455 530 x 530 605 x 605

STANDARD DIRECTIONAL CORE PATTERNS OF CEILING

DIFFUSERS

S ‘1’ Way S‘2’ Way

S ‘C’ Way S ‘3’ Way S ‘4’ Way

R ‘2’ Way ‘W’ Example R ‘3’ Way R ‘4’ Way

1 2 3 4 5 6
RCD 150X150 10 Type 'C' fixing Ral 9010 -

HAWA INDUSTRIAL
CEILING DIFFUSER
ENGINEERING AND PERFOMANCE DATA
Supply Square Ceiling Diffuser
One Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Supply Square Ceiling Diffuser

Two Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Supply Square Ceiling Diffuser

Three Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Supply Square Ceiling Diffuser

Three Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Supply Square Ceiling Diffuser

Four Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.75, 0.5 & 0.25 m/sec.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Return Square Ceiling Diffuser

One Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Return Square Ceiling Diffuser

Two Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Return Square Ceiling Diffuser

Three Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Return Square Ceiling Diffuser

Four Way Throw

• Neck velocity is measured in m/sec.

• PS: Static pressure loss across the diffuser is in mm of H2O.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
 CEILING DIFFUSER SRD/RRD
SUPPLY & RETURN ROUND DIFFUSER
The Round Ceiling Diffusers are designed for the HVAC
systems applications with high performance and noise free
operation. Each size has different numbers of cones, giving
uniformity of appearance where different sizes are used in the
same area. There are two distinct models: fixed and adjustable
types of core.
So if compared to the adjustable type, fixed core circular
ceiling diffusers have a lower throw level and can be used in
typical applications. Adjustable cone type is needed for
multiple height ceilings with a dome-like circular surrounding.

Construction:
 Frame and core: High quality extruded
aluminum construction.
 Damper frame and Blades: Steel sheet with
black matt finish.

Description:
 Inner cones fixed rigidly to the frame.
Standard Round air diffuser size:
 By pushing inward, turning, and pulling
downward, the core can be removed. This allows
Neck Size Face Size for simple installation, upkeep, and duct access.
Ø 150 Ø 250  Radial opposed blade damper is fixed to the
Ø 200 Ø 300 frame by rivets. Damper can be operated by
Ø 250 Ø 350 screw through diffuser face.
Ø 300 Ø 400  For adjustable type, discharge pattern can be
Ø 350 Ø 450 adjusted for horizontal flow by extending the core
and for vertical flow by retracting the core.
Ø 400 Ø 500
 The diffuser can be used for ceiling or exposed
Ø 450 Ø 550 duct mounting especially in installation when an
Ø 500 Ø 600 adjustable pattern is required.
 Circular ceiling diffuser can be fixed to extended
Standard Color: duct by rivets.
 As standard the grille is supplied in either off white
Fixing Details
RAL 9010 or white RAL 9016 polyester powder paint.

Ordering Data:
Specify
 1. HAWA type and model
 2. Neck Size  4. Surface finish
 3. Quantity  5. Remarks
Example Round Diffuser with Round Diffuser with
1 2 3 4 5 Butterfly Type Damper Rotating Type Damper
SRD Ø160 10 Ral 9010 -

Option:
 Wide selection of sizes.
 Any RAL color upon request
 Foam gasket is sealed around the back of the frame as Fixed Core Adjustable Core
option to avoid air leakage.

HAWA INDUSTRIAL
CEILING DIFFUSER

Round Ceiling Diffuser

Fixed Core

• Neck velocity is measured in m/sec.

• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.25 & 0.5 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER

Round Ceiling Diffuser

Adjustable Core

• Neck velocity is measured in m/sec.

• PS: Static pressure loss is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.25 & 0.5 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
CEILING DIFFUSER SPD/RPD
SUPPLY & RETURN PERFORATED CEILING DIFFUSER
Perforated ceiling diffusers are designed to provide a
smooth, even appearance that blends into the ceiling.
Perforated supply diffusers are available with adjustable
pattern controllers which provide an excellent air
pattern. The core is the same as in 4 – way throw ceiling
diffuser.

Construction:
 Frame : High quality extruded aluminum
 Flange width:30mm as standard
 Flange width: 16.24mm as option
 Perforated panel 0.8 mm thick galvanized
perforated steel sheet
Standard Color:  Plenum box are steel construction
 As standard the grille is supplied in either off white
RAL 9010 or white RAL 9016 polyester powder paint. Description:
 Frame is fabricated from high quality extruded
Standard sizes: aluminum profiles with the advantages of
 Available in square and rectangular sizes corrosion resistance and rigidity.
 Any combination of W x D  Perforated panel is fixed to the frame by screws.
Panel can be removed easily by loosening the
W= width in mm 150 225 300 375 450 525 600 screws.
 Different types of internal core can be fixed
D=depth in mm 150 225 300 375 450 525 600 inside the perforated panel as option.
 Core is fixed to the frame with aluminum pins
Ordering Data: loaded with steel springs.
Specify  Core can be easily removable and
interchangeable to allow for maximum flexibility
 1. HAWA type and model  4. Surface finish
in installation and maintenance.
 2. Nominal size - ØDiam  5. Remarks
 Supply air diffusers are provided with plenum
 3. Quantity
box.
 Because of high induction rates, velocity and
temperature will be equalized quite rapidly above
Example the occupied zone.
1 2 3 4 5
Option:
JN-EB Ø200 10 Ral 9010 -  Volume Control dampers as option
 Foam Gasket On The Back Of The Frame
 Wide Selection of Sizes, color

HAWA INDUSTRIAL
CEILING DIFFUSER SPD/RPD

Fixing Details:

 Concealed screw fixing from neck of the

diffuser to the duct.

Accessories:

1/Plenum:
 The plenum is constructed using G.I sheet.
 The plenum can be supplied with insulation from the
inside or outside as an option based on customer
requirement.
 Insulation material option: rubber foam / rock wool /
Fiberglass.
 The neck diameter ranges from 100mm – 450mm.

2/Damper:
 Damper is fixed rigidly to the frame by aluminum rivets.
Fixing by spring clips is optional.
 Damper blades are separated from its frame by nylon
bushes.
 Opposed blade damper is screw operated from the face
opening of the diffuser after removing the internal core.
Lever operated damper as option.
 Foam gasket is sealed around the back of the frame as
option to avoid air leakage.

3/Plenum & Damper:

 Foam gasket is sealed around the back of the frame as
option to avoid air leakage.

HAWA INDUSTRIAL
CEILING DIFFUSER SPD/RPD

Perforated ceiling diffuser air flow data & Standard

sizes:

Plenum Neck Size=150mmø, Module size=300X300mm

Plenum Neck Size=200mm ø, Module size=400X400mm

Plenum Neck Size=250mm ø, Module size=500X500mm

Plenum Neck Size=250mm ø, Module size=600X600mm

HAWA INDUSTRIAL
JET DIFFUSER

HAWA INDUSTRIAL
JET DIFFUSER JD-EB
JET DIFFUSER –EYE BALL
Jet Diffuser-Type Eye Ball Are Used For Preference Where
The Supply Air From The Diffuser Has To Travel A Large
Distance To The Occupied Zone. This Is The Case In Large
Rooms (Halls, Assembly Rooms Etc.), Particularly When The
Distribution Of Air Via Ceiling Diffusers Is Not Possible Or
Not Practical. Here Jet Diffusers Are Arranged In The Side
Wall Areas.

Construction:
 Frame : High quality extruded aluminum

Standard Color: Description:

 As standard the grille is supplied in either off white  Hawa eye ball jet diffusers are highly suitable
RAL 9010 or white RAL 9016 polyester powder paint. for delivering a powerful stream of air over long
distances.
Standard Jet Nozzle-Eye Ball Size:  It’s ideal for spot cooling applications.
 Long Distance Throws at High Outlet Velocities.
 Deliver an angular movement allows the
airstream through different directions.
 Can be adjusted over 180° as jet nozzle handle
different supply temperatures
 Removable Core to Allow For Better Flow
Direction.
 The Direction of the Air Stream Can Be Easily
Adjusted Manually to Suit Particular on Site
Conditions (upwards or downwards).
Ordering Data:
Specify Option:
 1. HAWA type and model  4. Surface finish  Can Be Sidewall Mounted Or Directly On
 2. Nominal size - ØDiam  5. Remarks Rectangular Or Round Ducts.
 3. Quantity  1, 2, 3 Or 4 Nos Of Jet Diffusers Will Be Arranged
In A Panel As Per Performance Requirement.
Example  Wide Selection of Sizes and Core Patterns.
1 2 3 4 5  Any RAL Color Upon Request
JN-EB Ø200 10 Ral 9010 -

HAWA INDUSTRIAL
JET DIFFUSER JD-EB

ENGINEERING AND PERFOMANCE DATA

JET DIFFUSER–EYE BALL

• Neck velocity is measured in m/sec.

• P= pressure losses across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
JET DIFFUSER JD-EB

ENGINEERING AND PERFOMANCE DATA

JET DIFFUSER–EYE BALL

• Neck velocity is measured in m/sec.

• P= pressure losses across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
JET DIFFUSER JD-EB

ENGINEERING AND PERFOMANCE DATA

JET DIFFUSER –EYE BALL

• Neck velocity is measured in m/sec.

• P= pressure losses across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.5 & 0.25 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
JET DIFFUSER JD-RT
JET DIFFUSER –RING TYPE
Jet Diffuser –Ring Type can deliver an accurate airstream
makes it suitable for spot cooling applications. HAWA Jet
Diffusers as they are highly suitable for conditioning large
spaces such as halls, warehouses, and auditoriums specially
designed to handle high air flow rates and provide relatively
long throws. Its angular movement allows the air stream to
be delivered through a wide area of direction either in full
jet position or in reduced jet position.

Construction:
 Frame : High quality extruded aluminum
 Outer flange: High quality extruded aluminum
profiles
 Inner ring: aluminum spun rings
 Plenum box either lined or unlined as per clients
choice.
Description:
 Frame and inner rings are high quality
aluminum construction with the advantage of
corrosion resistance.
 The jet nozzle section is mounted in a square
Standard Color: aluminum plate with a flanged border.
 As standard the grille is supplied in either off white  Jet Diffusers are available for sidewall and
RAL 9010 or white RAL 9016 polyester powder paint. ceiling applications.
 Nozzle can be adjusted 30° upwards and
 Ø100 downwards to achieve required throw as per site
 Ø150 condition. Nozzle jet can be rotated by 360° by
Standard Jet Nozzle-Eye Ball Size: adjusting the mounting frame.
 Ø200
Available from 100mm to 400mm dia  Ø250  Models in this series offer 1-4 units that can be
with the increments of 50 mm.  Ø300 built into one panel.
 Ø350
 Ø400 Option:
Ordering Data:   Wide Selection of Sizes and Core Patterns.
Specify  Any RAL Color Upon Request
 1. HAWA type and model  5. Surface finish  GI Plenum Box as option
 2. Neck diameter of the inner jet  6. Remarks  Units are available as a single diffuser, or
diffuser multiple
 3. No of diffuser  Plenum boxes can be supplied with round duct
 4. Quantity damper at the spigot as option

FIXING DETAILS
Example  Screw fixing from flange to duct.
1 2 3 4 5 6
HJD-RT ø250 2P 10 Ral 9010 Plenum Box

HAWA INDUSTRIAL
JET DIFFUSER JD-RT

PANEL ARRANGMENT
 1, 2, 3 or 4 nos of jet diffusers will be arranged in a panel as per performance requirement.

Model Duct Size L x W A B C Duct Size L x

Model A B (ø) E
JD-RT-100-2P 390x200 440 250 200 W
JD-RT-100-3P 580x200 630 250 200 JD-RT-100-P 200x200 250 250 100
JD-RT-100-4P 790x200 840 250 200 JD-RT-150-P 250x250 300 300 150
JD-RT-150-2P 490x250 540 300 250 JD-RT-200-P 300x300 350 350 200
JD-RT-150-3P 730x250 780 300 250 JD-RT-250-P 350x350 400 400 250
JD-RT-150-4P 990x250 1040 300 250 JD-RT-300-P 400x400 450 450 300
JD-RT-200-2P 590x300 640 350 300 JD-RT-350-P 450x450 500 500 350
JD-RT-200-3P 880x300 930 350 300 JD-RT-400-P 500x500 550 550 400
JD-RT-200-4P 1190x300 1240 350 300
JD-RT-250-2P 690x350 740 400 350
JD-RT-250-3P 1030x350 1080 400 350
JD-RT-250-4P 1390x350 1440 400 350
JD-RT-300-2P 790x400 840 450 400
JD-RT-300-3P 1180x400 1230 450 400
JD-RT-300-4P 1590x400 1640 450 400
JD-RT-350-2P 890x450 940 500 450
JD-RT-350-3P 1330x450 1380 500 450
JD-RT-350-4P 1770x450 1820 500 450
JD-RT-400-2P 990x500 1040 550 500
JD-RT-400-3P 1480x500 1530 550 500
JD-RT-400-4P 1970x500 2020 550 500

HAWA INDUSTRIAL
JET DIFFUSER JD-RT

ENGINEERING AND PERFOMANCE DATA

JET DIFFUSER –RING TYPE

AT 0° POSITION

• Neck velocity is measured in m/sec.

• PS & PV=Static and dynamic pressure losses across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.25 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
JET DIFFUSER JD-RT

ENGINEERING AND PERFOMANCE DATA

JET DIFFUSER –RING TYPE

AT 30° POSITION

• Neck velocity is measured in m/sec.

• PS & PV=Static and dynamic pressure losses across the diffuser is in mm of H2O.
• Throw (meters) is measured for terminal velocities of 0.25 m/s.
• NC based on a room attenuation of 10 db.

HAWA INDUSTRIAL
DISC VALVE

HAWA INDUSTRIAL
DISC VALVE DV

DISC VALVE
HAWA disc valves are best suited to air distribution systems
handling relatively low air flow rates within small circular duct
work.. Additionally, it has a center thread bar adjustable
positions. Disc valves are preferred by many architects and
building owners for toilets, bathrooms and ventilation in damp
areas due to its simplistic yet aesthetic appearance.

Construction:
 Frame and disc: Steel sheet construction.
 Mounting rings: Galvanized sheet steel.

Description:
 The air flow required can be easily preset by
adjusting the inner ring position.
 The air flow through the disk valve can be
adjusted by rotating the disc clockwise or
anticlockwise.
 The rotation changes the free area between
the disc and the frame.
 Disc is attached to the frame by threaded rod.
 Air flow can be adjusted by regulating the cone
Standard Disc Valve Size:
up or down (+A,-A).
 Disc valves can be used for supply, exhaust
and ventilation application.
 HAWA disc valves are recommended for
exhaust of damp air in area such as toilets,
bathrooms and kitchen.

Option:
 Foam gasket is sealed around the back of the
frame as option to avoid air leakage.
 Can be mounted in wall, ceiling or exposed air
ducts with mounting rings.
 Wide Selection of Sizes and Core Patterns.
 Any RAL Color Upon Request

Ordering Data: Fixing Details

Specify
 4. Surface finish
 1. HAWA type and model  5. Remarks
 2. Nominal size - ØDia
 3. Quantity

Example
1 2 3 4 5
DV Ø200 10 Ral 9010 -

HAWA INDUSTRIAL
DISC VALVE DV
ENGINEERING AND PERFOMANCE DATA

Supply Air Disc Valve

Note:
 For position A=+10, Reduce Throw By 30%.
 For position A=-10, Reduce Throw By 40%.

Supply air volume VS Throw in meters for (A=0)

• Pt= Total pressure loss across the disc valve in mm of H2O

• NC based on a room attenuation of 10 dB.
• A=+10, 0 & -10 Represents Position Of The Disc 10mm Below Normal Position, At Normal
Position And 10 Mm Above Normal Position . DV

HAWA INDUSTRIAL
AIR LOUVER

HAWA INDUSTRIAL
AIR LOUVER EAL/EAL-D
EXHAUST AIR LOUVER
Exhaust air louver are mainly used in the ventilation system
of a building. The fixed blades of a louver are arranged in such
a way that is allows the flow of air meanwhile preventing the
ingress of water at nominal velocities.

Our louvers can also provide architectural style to building

design. With the variety of models, sizes, and paint finishes
available, Ruskin Louvers can add unusual and appealing
features to exterior and interior elevation.

Construction:
 Material: High Quality Extruded Aluminum
profile of 1 or 2 mm thickness.
 Blade pitch: 40 mm standard
 Flange width:30mm standard

Description:
 Composed of frame and horizontal blade
assembly made of high quality extruded
aluminum profile with the advantages of
durability and corrosion resistance.
 Designed to have sturdy construction. Blades
are fixed to the main frame using screws and
riveted to the mullions for bigger sizes.
 Weather resistant structure with blades
inclined at an angle of 45o to protect against
rain water penetration.
 Assembly provides around 45% effective
pressure areas.
Exhaust Exhaust air louver
 Multiple sections will be assembled as per
air louver with damper request. Damper blades can be controlled
manually using the lever provided.
 A 1 cm clearance is deducted from your order neck size.
Option:
 Filter thickness: 15mm , 30mm or 50mm
Ordering Data:  Insect Screen
 Any RAL Color Upon Request
Specify
 1. HAWA type and model  4. Type of fixing
 2. Nominal size – L x W  5. Surface finish
 3. Quantity  6. Remarks

Example
1 2 3 4 5 6
EAL-D 1700x900 2 Ral 9010 Type ‘S’ fixing Damper

Standard Profile Frame Optional Box Frame

HAWA INDUSTRIAL
AIR LOUVER FAL/FAL-D/EAL/EAL-D

ENGINEERING AND PERFOMANCE DATA

Fresh-Exhaust Air Louver

Face Velocity VS Pressure Drop

 Intake Pressure Drop Includes pressure drop across filters
 Values are taken when the damper is in fully opened condition.

Effective pressure area in sq.m

 Effective pressure areas for non-standards sizes can be interpolated from the above data.

HAWA INDUSTRIAL
AIR LOUVER HDAL
HEAVY DUTY AIR LOUVER
Heavy Duty Air Louver is used in a multitude of industrial
applications, but primarily in supply/exhaust ventilation
systems.

These louvers are used in applications that are exposed to

weather conditions of rain and snow, in corrosive
environments and for noise mitigation applications.

Construction:
 Material: High Quality Extruded Aluminum
profile of 2.2 mm thickness.
 Blade pitch:80 mm standard
 Flange width:40mm standard

Description:
 Used in heavy duty applications that requires
extremely sturdy construction.
 Designed to provide more than 65% effective
pressure area thereby having lesser pressure
 A 1 cm clearance is deducted from your order neck size. drop.
 Weather resistant structure with blades
inclined at an angle of 45° to protect against
rain water penetration.
 Composed of frame horizontal blade assembly
made of high quality extruded aluminum profile
with the advantages of durability and corrosion
resistance.
 Blades are fixed to the main frame using
screws and riveted to the mullions for bigger
sizes to have better rigidity.
Multi Section Fixing Details

Ordering Data: Option:

 Filter thickness: 15mm or 45mm
Specify  Mesh :
 4
 1. HAWA type and model  4. Type of fixing  12 x 12 x 1.5mm dia alum PVC coated wire
.
 2. Nominal size – L x W  5. Surface finish
mesh
 3. Quantity  6. Remarks
T  12 x 12 x 1mm dia G.I wire mesh
y  SS Mesh
p  Insect Screen
Example e  Optional Frame and Blade: 2mm thick profile
1 2 3 4 5 6 is available for heavy duty application.
HDAL 1700x900 2 Ral 9010 Type ‘S’ fixing - o  Any RAL Color Upon Request
f  Multiple sections will be assembled as per
request.
f
HAWA INDUSTRIAL
i
AIR LOUVER HDAL

ENGINEERING AND PERFOMANCE DATA

Heavy Duty Air Louver

Face Velocity VS Pressure Drop

Effective pressure area in sq.m

HAWA INDUSTRIAL
SAND TRAP LOUVER

HAWA INDUSTRIAL
SAND TRAP LOUVER STL-BS/STL-F/ STL-FD
SAND TRAP LOUVER
Our Sand Trap Louver designed to remove the bulk of airborne
sand and dust from inlet air in dry, dusty or sandy climates
whilst maintaining reasonable air flow rate characteristics by
means of a double blade design. Our sand trap louvers are
capable of performing as natural ventilators or to alleviate the
load on the main filtration stages of air conditioning equipment.

Sand and dust is evacuated from the base of the louver by means
of slots in the base, keeping maintenance to a minimum and
ensuring the design airflow rate under all conditions.
Construction:
 The frame: 1 mm and 2 thick high quality
extruded aluminum profiled construction.
Sand trap louver with filter  Frame profile 25 mm flange width & 150mm
height.
 Channels profile 100mm face width & 30mm
height.
 Bird screen: 12mm x12mm x1mm Diameter GI
wire mesh as standard.
 Drain: two set of 20mm diameter self-drain
holes at the bottom of the louver.

Description:
 The frame and blades are of high quality
extruded aluminum profiled construction with
the advantages of corrosion resistance and
rigidity.
 Drain holes of diameter 20 mm are provided in
two rows at the bottom of the louver for
empting filtered sand and dust.
 Designed to separate sand and duct from the
air stream.
 Composed two sets of inverted U-channels
With A With a With Bird mounted vertically on two opposite rows.
Removable removable filter Screen and  Fixed with a removable washable extruded
Filter and a volume volume aluminum filter with aluminum mesh as the
control damper control filter media.
Damper  Fixed with a removable washable extruded
aluminum filter with aluminum mesh as the
Sand rejection efficiency:
filter media.
Tests conducted on Model: STL-W at a face velocity of
0.5 m/sec indicates a typical efficiency of:
Option:
 90 percent on 200 to 700 microns  Available with Bird screen
 80 percent on 20 to 200 microns  Available with GI mesh filter
 50 percent on 1 to 70 microns  Available with volume control damper
 For bigger sizes, several sections can be
Better efficiency can be achieved by sand trap lovers combined to provide any combinations of
with washable aluminum filters. overall width W or height H.
 Any RAL Color Upon Request

HAWA INDUSTRIAL
SAND TRAP LOUVER FSTL-BS/FSTL-F/ FSTL-FD
FLUSH MOUNTED SAND TRAP LOUVER
Flush mounted Sand Trap Louver is an intake sand trap
Louver with Bottom Flush Type Design.

This model is Usually Used When the FSTL Is Required to Be

Installed in Plane with the External Wall of the Building from
Outside.

This sand trap louver is provided with a sand chute tray to

ensure the discharge of captured sand or duct to outside the
building.
Construction:
 The frame & blades: 1 mm and 2 thick high
quality extruded aluminum profiled
construction.
 Bird screen: 12mm x12mm x1mm Diameter
GI wire mesh as standard.
 Sand chute: Aluminum sheet tray of 1 or
2mm thickness.

Description:
 Small size and flexibility, due to modular
concept.
 Low cost and long life product design
 Can be done with horizontal louvers or vertical
louvers.
 Surface of the louver is fixed flush on the plane
of the wall. The filtered sand will be drained
through a sand chute.
 Sand chute is an inclined tray fixed at the
bottom of the louver for sand drain.
 Have a high degree of separation capability of
sand and large dust particles, even in case of
high dust concentrations.
Sand trap louver with filter  For a much better filtration, sand trap louver is
provided with a detachable Aluminum filter of
thickness 15mm or 30mm.
 Fixed with a removable washable extruded
aluminum filter with aluminum mesh as the
filter media.
 Fixed with a removable washable extruded
aluminum filter with aluminum mesh as the
filter media.

Option:
 Available with insect screen
With a removable  Available with aluminum mesh filter
With a removable filter filter and a volume  Available with volume control damper
control damper  For bigger sizes, several sections can be
combined to provide any combinations of
overall width W or height H.
 Any RAL Color Upon Request

HAWA INDUSTRIAL
SAND TRAP LOUVER
Fixing Details

Concealed Screw Fixing Flush Mount Sand Trap Multi-Section

louver Fixing Arrangement
Engineering and Performance Data
For a known air quantity, calculate face area as
follows:

The length (m) and width (m) of sand trap louver can
be determined from the face area calculated with
respect of the opening provide at the site.
If only free area is known, calculate face area as
follows:
Face area (m2) = Free area (m2) x2.7

The length (m) and width (m) of sand trap louver can
be determined from the face area calculated with
respect to the opening provided at the site.

Note: for optimum performance of sand trap louver

with lower pressure drop and high efficiency, we
recommend a face velocity of up to 1m/s.

HAWA INDUSTRIAL
HAWA UAE

Location: Factory: umm al Quwain, umm

Thaob Industrial Area.

Head Office: Sharjah, Al Ghanem business

center office 610

Phone +971 065375000

E-mail: [email protected]

www.hawaindustrial.com

HAWA QATAR

New Industrial Area, Doha Qatar

Phone +974 44152035

+974 70736995

Fax: +974 44984151

P.O. Box 90126 | Doha | Qatar

E-mail: [email protected]

www.everythingducting.com

HAWA INDUSTRIAL