Operating Instructions (EN)

MODELS:
Micro-HD
20''-26'' Disk
25'' Cylindrical
20'', 24'' & 28'' Orbital

Mini-HD
26''-28'' Disk
25''-29'' Cylindrical
24''-28'' Orbital

Mag-HD
30'', 32'' & 34'' Disk
29''-33'' Cylindrical
28''-32'' Orbital

Read these Instructions be-

fore using the machine.

Read these Safety Messages

before using the machine.

www.factorycat.com
1711 South Street
Racine, WI 53404 (USA)
1-262-681-3583 V24.016
© 2024 RPS Corporation, All Rights Reserved. FC-WALK-BEHIND-V2-SERIES-OP-EN
 INTRODUCTION
This manual is furnished with each new machine. This manual will allow the Operator to get the best performance
out of your RPS manufactured Scrubber-Drier, Sweeper, Burnisher, or Orbital Scrubber. Read this manual thoroughly
before operating or servicing the machine.

This machine will provide excellent performance, but the best results will be obtained at the most minimum costs if:

• The machine is regularly maintained - per the Authorized Local Distributor.

• The machine is operated with reasonable care and caution.

• The machine is maintained with manufacturer supplied parts.

LOCATE SERIAL NUMBER

The serial number of your machine is located on the lower half of the control panel of the machine.

DEALER INFO SERIAL NUMBER

AS OUR POLICY IS ONE OF CONSTANT IMPROVEMENT - ALL INFORMATION AND

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

-2- FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016

 TABLE OF CONTENTS

Introduction 2 PM Sheet 38

Locate Serial Number 2 Membrane/Touch Screen Error Codes 40

Table Of Contents 3 Membrane/Touch Screen Error Codes 41

Safety Messages 4 Touch screen schematics 42

Safety Labels 6 Military grade schematic  43

Dashboard Controls (Military, Legacy, Touch Screen, membrane) 7 Membrane Schematics 45

Central Command Side Panel Controls 8 Legacy schematic  46

legacy LCD Screen (Micro-HD/Mini-HD only) 9 MACHINE DECALS 47

Touch Screen (Optional) 10 Micro-HD Common Wear Parts 48

Round Disk Brushes: 48
Membrane (Mag-HD only) 14
Round Disk Pads: 48
Cylindrical Brushes: 48
Battery Setup 18
EDGE Pads and Screens: 48
EDGE Grip Face: 49
install Squeegee 19
v2.1 Squeegee Blade Kits & Complete Squeegee
Assemblies: 49
Adjust Squeegee 20
Mini-HD Common Wear Parts 50
Remove From Battery Charger 21 Round Disk Brushes: 50
Round Disk Pads: 50
Transportation - Forward 22
Cylindrical Brushes: 50
EDGE Pads and Screens: 50
Transportation - Reverse 23
EDGE Grip Face: 51
v2.1 Squeegee Blade Kits & Complete Squeegee
Fill Solution Tank 24 Assemblies: 51
Operation - Scrubbing 25 MAg-HD Common Wear Parts 52
Round Disk Brushes: 52
Draining Recovery Tank 26 Round Disk Pads: 52
Cylindrical Brushes: 52
Draining Solution Tank 27
EDGE Pads and Screens: 52
EDGE Grip Face: 53
Flushing Recovery Tank 28
v2.1 Squeegee Blade Kits & Complete Squeegee
Assemblies: 53
Clean Drain Saver 29

Clean Cylindrical Hopper 30

Clean Vac Box System 31

Remove Disk Brushes 32

Remove Cylindrical Brushes 33

Remove Orbital Pads 34

Charge Batteries 35

Battery Chargers 36

Military Central Command status light codes  37

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 -3-

 SAFETY MESSAGES

You will see four kinds of safety reminders in this manual:

DANGER WARNING
DANGER indicates a hazardous situation which, if not WARNING indicates a potentially hazardous situation
avoided, will result in death or serious injury. which, if not avoided, could result in death or serious
injury.

CAUTION NOTICE
CAUTION indicates a potentially hazardous situation NOTICE indicates information considered important,
which, if not avoided, could result in minor or moderate but not hazard-related. This safety message may be
injury or damage to this machine or nearby objects. related to property damage or warranty warnings.
CAUTION also can be used to alert against unsafe prac-
tices.

Your safety, and that of others, is very important. Operating this machine safely is an important responsibility.

DO NOT OPERATE THIS MACHINE:

• Unless you are trained and authorized to do so by your RPS Authorized Local Distributor
• Unless you have read and understood this Operator’s Manual
• On surfaces with greater than a 2% grade unless this machine is equipped with a functional parking brake
• On surfaces with greater than an 8% grade at any time
• On Loading Docks

WHEN OPERATING THIS MACHINE:

• Remove loose objects from the floor that could be projected from the rotating Brushes
• Keep your hands and feet away from the rotating Brushes
• Do not operate this machine where flammable liquids, vapors, or dust are present
• Use caution when maneuvering

BEFORE LEAVING THE MACHINE:

• Drain “clean” Solution & “dirty” Recovery solution into APPROVED drains
• Park the machine on a level surface
• Turn the machine off & remove key

BEFORE SERVICING THE MACHINE:

• Disconnect the Batteries
• Drain both tanks

DANGER DANGER
Explosive hydrogen gas forms when Batteries are Flammable materials can cause an explosion or fire.
charging. An open flame or spark can cause this gas to Do not use flammable materials in Tank or pick up.
explode. Serious personal injury or property damage
could occur. Only charge the Batteries in this machine
in a well ventilated area.

-4- FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016

 WARNING WARNING
The Batteries in this machine produce hazardous Dress safely. Do not wear rings or metal wrist watch-
voltage which can cause electrical shock, burns and/ es when servicing this machine, as they can cause
or electrocution. Always disconnect Batteries before an electrical short circuit which can cause serious
servicing this machine. burns.

WARNING WARNING
When climbing or descending ramps, always drive Do not remove, paint over or destroy warning decals.
machine forward. To avoid overturning the machine, If warning decals become damaged, call 1-262-681-
Do not back down ramps. Do not drive across 3583 for free replacements.
inclines. Do not turn while ascending or descending
ramps. Overturning the machine can cause serious
injury or death.
WARNING
Dress safely. Do not wear a neck tie, scarf, or any
WARNING loose or dangling clothing while operating this
machine. Loose or dangling clothing or neck-wear
Do not use water that exceeds 135°F / 57°C. If water can tangle in rotating parts, causing serious injury or
is above said temperature, this will void the Tank death.
Warranty.
WARNING
WARNING Always turn off this machine before leaving it
Do not park this machine on ramps or slopes. unattended. Do not allow untrained persons to
Always park this machine on a level, hard surface. operate this machine.
Do not operate this machine outdoors or on uneven
surfaces.
WARNING
WARNING NO RIDERS. Do not carry passengers on this
machine. Do not use this machine as a stepladder or
The Batteries in this machine contain sulfuric acid, work platform.
which causes burns to skin. If battery acid contacts
clothing or skin, rinse the effected area with cold
water immediately. If battery acid gets on your face
WARNING
or in your eyes, flush the area immediately with cold Understand the dynamic braking system before you
water and seek medical attention. operate the machine on ramps. Machine may coast.

WARNING WARNING
To avoid electrical shock, do not operate this ma- Before you service a Battery, always wear face
chine over electrical floor outlets. protection, protective gloves and protective clothing.
Battery acid or battery explosion can cause serious
injuries.

CAUTION CAUTION
To avoid damage to this machine, use only cleaning Always use the automatic battery charger provided
solutions and replacement parts recommended by by the manufacturer of this machine to charge the
the manufacturer. Batteries of this machine. It is designed to charge
the Batteries at the appropriate rate. If you must use
CAUTION a different charger, disconnect the Batteries before
charging to avoid damage to the electronic speed
Do not operate this machine if any parts have been controller.
damaged or removed.
CAUTION
To avoid damage to the electronic control compo-
nents of this machine, Do not store this machine
outdoors. Do not pressure wash this machine.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 -5-

 DANGER

SAFETY LABELS

Read and obey all Safety Labels on your Floor Scrubber. If you have questions about these labels, ask your supervi-
sor.
These images indicate where on the Floor Scrubber the Safety Labels are located. If ever the labels become illegible,
worn off, or torn, promptly report it to your supervisor and replace it.

SEE BACK PAGE FOR DECAL PART NUMBERS

-6- FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016

DASHBOARD CONTROLS (MILITARY, LEGACY, TOUCH SCREEN, MEMBRANE)

1
Military Grade
1. Squeegee Lever
2. Reverse Switch 9 10 11 12
15 16
3. Drive Switch (Both Handles)
4. E-Stop 2
5. Key Switch
6. Vac Clog Light 3 4
7. ZerO3 Light
8. Speed Potentiometer 5 8
6 14
9. Vac Switch
10. Solution Switch +/-
13
11. Scrubdeck Switch +/- 1
Legacy (Micro-HD/Mini-HD)
12. Down pressure Switch 9
13. Military Flow Lever 18
17
14. Military Status Light
11
15. Military Battery Gauge / Hour Meter Combo
2 4
16. Military Down Pressure Gauge
17. LCD Screen
3
18. Legacy Hour Meter Button
19. Batteries
20. Vac Light 5 6 7 8
10 12
21. Solution Light
22. Scrubdeck
1 Touch Screen
23. Zone 1
See Pg. 11 for Touch Screen Operation
24. Zone 2
25. Zone 3
26. Suds (Off, Normal, 2x Dose)

27. Traction 2

3 4

5 8
6 7
1 Membrane (MAG-HD Only)
7 23 24 25 26
4 10 12

2 17
27
21
3

5
19 6 20 22 9 11 9,11 8

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 -7-

 CENTRAL COMMAND SIDE PANEL CONTROLS

1 2 3 6 4 5 4 5
4 6 5
4
11
5 7 7
14 7
10 8
6
8
7
8

9 9 9
12 13
Military Grade Legacy (MICRO-HD/MINI-HD) Touch Screen Membrane

1. Vac Circuit Breaker 6. ZerO3 Circuit Breaker 11. Military Solution Control Lever
2. Left Brush Circuit Breaker 7. Spray Jet On (I) / Off (O) 12. Legacy ECON switch Max
3. Right Brush Circuit Breaker 8. ZerO3 On (I) / Off (O) (locked) Min (unlocked)

4. Positive BUSS Circuit Breaker 9. Dual USB Voltmeter 13. Legacy Dual Manager Lockout
Solution/Downpressure
5. Negative BUSS Circuit Breaker 10. Solution Valve Circuit Breaker
14. Suds Switch 125:1/ 250:1/ Off (O)

-8- FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016

 LEGACY LCD SCREEN (MICRO-HD/MINI-HD ONLY)

SCREEN #1 (OPERATOR) SCREEN #2 (MAINTENANCE)

10
1 2 3 4 5 6

SCREEN #3 (WITH ERROR CODE)

11

12

** USE GREEN MENU SELECTION BUTTON ON CONTROL PANEL TO CHANGE SCREENS **

1. BATTERY LEVEL INDICATOR - Indicates the energy level remaining in the Batteries (Shown on all menu displays)
2. SOLUTION OUTPUT INDICATOR - Indicates the gallons per minute (GPM) 0 - 1.0
3. SCRUBDECK DOWN PRESSURE INDICATOR - Sets the down pressure on the Brushes / Pads
4. SCRUB MOTORS ON - Indicates the Brush Motors are in operation
5. SOLUTION ON - Indicates the solution flow is ON
6. VACUUM ON - Indicates the Vacuum is ON
7. KEY SWITCH HOUR METER - Indicates total hours the machine has had keyswitch ON
8. TRANSPORT HOUR METER - Indicates total hours the drive system has been in operation
9. SCRUB BRUSH HOUR METER - Indicates total hours the brush motors have been in operation
10. VACUUM HOUR METER - Indicates total hours the vacuum motor has been used
11. DIAGNOSTIC CODE - Displays diagnostic code which helps troubleshoot issues
12. ERROR WARNING SYMBOL - Indicates when there has been a diagnostic code error

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 -9-

 3

TOUCH SCREEN (OPTIONAL)

#1 NAME

SUDS

1 2 3 4 5

3
#1

SUDS
7

24.9
22.5 34.2

8 9 10 11 12

1. SOLUTION OUTPUT - Indicates the level of solution that is being dispensed when in operation, (0 = off, 1 = Low, 4 = High).
2. TECHNICAL / MANAGER SETUP - Access ‘Error Code History’ and Manager Programming
3. PROGRAMMED ZONES - Switch between preset solution and downpressure settings for varying applications
4. HOUR METERS - Displays all of the hour meters of the machine: Key Switch, Transport, Scrub Motors, and Vacuum Motor
5. DOWN PRESSURE OUTPUT - Indicates the level of downpressure that is being applied to the floor surface (1 = low, 4 =
high).
6. BATTERY GAUGE - Indicates the level of battery charge available and volt meter
7. SUDS - (Onboard Chemical Dilution) indicator

8. ACTIVE VOLT & AMP DRAW - Indicates the live DC Volts (under battery gauge) and Amp draw (under systems) when ma-
chine is running
9. AMP VAC CURRENT - Indicates Vac power consumption
10. TRANSPORT INDICATION - Green Forward & Red Rev
11. BRUSH DISK CURRENT - Indicates Brush power consumption
12. OPERATION MODE SELECTOR - Cycle through and select which operation mode you would like to work in

- 10 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 3

TOUCH SCREEN SYMBOLS (OPTIONAL)

#1 NAME

SUDS

Mode Selection
Transport Only Single Scrub Double Scrub Vacuum Only

Solution Setting
#0 #1 #2 #3 #4

Down Pressure Setting

#1 #2 #3 #4

Forward Transport Motor Reverse Transport Motor

Working Active Inactive Working Active Inactive

Solution Flow Vacuum Motor

Working Active Inactive Working Active Inactive

Suds Scrub Deck Motor(s)

250:1 Dilution 125:1 Dilution Inactive Working Active Inactive

SUDS SUDS SUDS

Setup Hour Meters Zone Lock
Locked Unlocked

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 11 -
 3

TOUCH SCREEN ZONE OPERATION (OPTIONAL)

#1 NAME

SUDS

The touch screen is designed to be programmed to three specific

3 zones. Each zone can be named and custom programmed or even
LIGHT DUTY disabled if not needed.
The zone you are working in is highlighted as indication. In Figure
1. the zone selected is Light Duty.

SUDS

Figure 2. shows Zone 3 “locked out” by the indicator lock icon.

3
LIGHT DUTY

SUDS

Figure 3. shows Zone 1 “Light Duty” Factory Configuration.

3 Water = 1

LIGHT DUTY Downpressure = 2

Drive Speed = 70%
Vac Motor = 80%

% %

Figure 3. shows Zone 2 “Daily” Factory Configuration.

3 Water = 2

DAILY Downpressure = 3
Drive Speed = 90%
Vac Motor = 90%

% %

Figure 3. shows Zone 3 “Heavy Duty” Factory Configuration.

Water = 3

HEAVY DUTY Downpressure = 4

Drive Speed = 100%
Vac Motor = 100%

% %

- 12 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 3

TOUCH SCREEN ZONE PROGRAMMING (OPTIONAL)

#1 NAME

SUDS

To program the 3 Zones, press

3
LIGHT DUTY

SUDS

From here you will be prompted with a passcode screen. Enter the
manager passcode 349 to get access to setup.

Once you have entered the password, you will see the Figure 3.
screen where you can alter the name, solution output, down-pres-
sure setting, scrubbing speed, and vacuum power.
Alternatively you can lock the Zone out from this screen, to pro-
hibit operator use.
Once any of the 3 “Zones” is locked the remaining zones are no
longer adjustable either by the operator.

To alter the name of a Zone, simply click on the black name box
and a full keyboard will appear as Figure 4. shows. Enter new name
and save your work with the Green save icon.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 13 -
 3

MEMBRANE (MAG-HD ONLY)

#1 NAME

SUDS

1 8 3 7 5

2 4
9
10
6
12 13

11 14

1. SOLUTION OUTPUT - Indicates the level of solution that is being dispensed when in operation, (0 = off, 1 = Low, 4 = High).
2. TECHNICAL / MANAGER SETUP - Access ‘Error Code History’ and Manager Programming (Press and Hold 1 & 3 for 5 seconds).
3. PROGRAMMED ZONES - Switch between preset solution and downpressure settings for varying applications
4. HOUR METERS - Displays all of the hour meters of the machine: Key Switch, Transport, Scrub Motors, and Vacuum Motor

5. DOWN PRESSURE OUTPUT - Indicates the level of downpressure that is being applied to the floor surface (1 = low, 4 = high).
6. BATTERY GAUGE - Indicates the level of battery charge available and volt meter
7. SUDS - (Onboard Chemical Dilution) indicator ( OFF, Normal, 2x Dose)
8. ZerO3 - (Chemical Free Auquous Ozone) indicator

9. ACTIVE VOLT & AMP DRAW - Indicates the live DC Volts (under battery gauge) and Amp draw (under systems) when machine is running
10. OPERATION MODE SELECTOR - Cycle through and select which operation mode you would like to work in
11. VAC LIGHT- Indicates when vacuum is on
12. VAC CLOG LIGHT- Indicates when vacuum is clogged
13. SOLUTION LIGHT- Indicates active solution to scrub deck
14. SCRUB DECK LIGHT- Indicates active scrub deck

- 14 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MEMBRANE (MAG-HD ONLY)

Mode Wheel
Traction Only

Scrubbing + Vacuum

Vacuum Only

Scrubbing Only

1 2
LCD Display

CLEAR WINDOW

3 4

1. BATTERY VOLTAGE READOUT

2. SCRUBDECK AMPERAGE READOUT
3. TRACTION VOLTAGE READOUT
4. VACUUM AMPERAGE READOUT

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 15 -
 3

MEMBRANE (MAG-HD ONLY)

#1 NAME

SUDS

Programming Zones
1 Hold 5 sec
3

2
CLEAR WINDOW CLEAR WINDOW

4 4
5 6

CLEAR WINDOW
1. LOW
2.
3.
4. HIGH

1 HOLD (1) & (3) FOR 5 SEC

1.
Operator Video
2 SELECT SETUP (2)
2.
3 SELECT LEVEL
3.

4 WATER/DOWNPRESSURE CHANGES VALUES

4.

5 PUSH ZERO3 TO SWAP SCREENS

5.
6.
6 PUSH SUDS TO SAVE

- 16 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MEMBRANE (MAG-HD ONLY)

Checking Hour Meters & Error Codes

Hold 5 sec

CLEAR WINDOW CLEAR WINDOW

Select (3)

CLEAR WINDOW CLEAR WINDOW

Membrane Zones Factory Default

1 1 1 2 2 3 3 3 4

1 1 2 2 3 4
FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 17 -
 BATTERY SETUP

4
5

NOTICE
Batteries are a possible environmental hazard. Con-
sult your Battery supplier for safe disposal methods.

NOTICE
Orientation of Batteries is critical for cables to reach.
Ensure proper torque values when installing batteries.
(Between 8 - 12 ft/lbs)

- 18 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 INSTALL SQUEEGEE

2 1

3 3

4 4

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 19 -
 ADJUST SQUEEGEE

2 1

(RH) (LH)
1/2'' 5/16''

- 20 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 REMOVE FROM BATTERY CHARGER

Please refer to OEM Charger Operating Instructions for more information.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 21 -
 TRANSPORTATION - FORWARD

Military Grade

3
40% 2

Legacy

1 3

40% 2

Touch Screen

40% 3

Membrane (Mag-HD)

4
40% 3

- 22 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 TRANSPORTATION - REVERSE

Military Grade

40% 2

Legacy (MICRO-HD/MINI-HD)

40% 2

Touch Screen

2
4

40% 3

Membrane (Mag-HD)

4 2

40% 3

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 23 -
 FILL SOLUTION TANK

< 135°F / 57°C

DANGER CAUTION
EXPLOSION RISK! Flammable materials can cause an TO AVOID DAMAGE TO THIS MACHINE:
explosion or fire. Do NOT use flammable materials in • Use APPROVED detergents only
Tank or pick up. • Water temperature must not exceed 135˚F/57˚C
• Do NOT use high-percentage Bleach mixture

< 135°F / 57°C

- 24 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 OPERATION - SCRUBBING

7 Military Grade

2 3 4 5 5

8
40% 6

6
Legacy

2 3
1
7
40% 5

2 3

4 Touch Screen

5
40% 3

4
Membrane (Mag-HD)

4
40% 3

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 25 -
 WASTE WATER DRAINS ONLY!

DRAINING RECOVERY TANK

WASTE WATER DRAINS ONLY!

- 26 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 WASTE WATER DRAINS ONLY!

DRAINING SOLUTION TANK

WASTE WATER DRAINS ONLY!

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 27 -
 FLUSHING RECOVERY TANK

- 28 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 CLEAN DRAIN SAVER

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 29 -
 CLEAN CYLINDRICAL HOPPER

- 30 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 CLEAN VAC BOX SYSTEM

2
1
4
3
1 4
3

5 6

8
7

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 31 -
 REMOVE DISK BRUSHES

Left Right

Rotate after 25 hrs

- 32 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 REMOVE CYLINDRICAL BRUSHES

2
Rotate after 25 hrs

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 33 -
 REMOVE ORBITAL PADS

2 Grip Face

Spacer
Prep Pad

Never place Prep Pad

directly on Grip Face!

- 34 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 CHARGE BATTERIES

Please refer to OEM Charger Operating Instructions for more information.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 35 -
 BATTERY CHARGERS

Console / WET / Domestic Chargers:

AC Power IN: 120VAC / 60Hz

DC Power OUT:
Micro-HD: 24VDC / 12A
Mini-HD: 24VDC / 25A
Mag-HD: 24VDC / 30A

Please refer to OEM Charger Operating Instructions for

more information.

Onboard / AGM / International Chargers:

AC Power: 80-270VAC / 50-60Hz

DC Power OUT: 24VDC / 27A

Please refer to OEM Charger Operating Instructions for

more information.

- 36 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MILITARY GRADE CENTRAL COMMAND - STATUS LIGHT CODES

Status Light Guide

Below is a list of self-help actions. Try to use this list before you contact your service agent. Go to the number in the
list which matches the number of indicator light flashes and follow the instructions.
1 Flash The battery needs charging, there is a bad connection to the battery or dependent
on programming, may indicate that the battery lockout function is active and the
controller is in a restricted mode of operation. Check the connections to the battery.
If the connections are good, try charging the battery.
2 Flash
There is a bad connection to the motor. Check all connections between the motor
and the controller.

3 Flash
The motor has a short circuit to a battery connection. Contact your service agent.

4 Flash
The battery charge level has fallen below the Battery Lockout Level and the
controller is inhibiting certain machine functions. Charge the battery.

5 Flash
Not Used.

6 Flash
The controller is being inhibited from driving, this may be because the battery
charger is connected.

7 Flash
A throttle fault is indicated. Make sure that the throttle is in the rest position before
switching on the machine.

8 Flash
A controller fault is indicated. Make sure that all connections are secure.

9 Flash
The parking brakes have a bad connection. Check the parking brake and motor
connections. Make sure the controller connections are secure.

10 Flash
An excessive voltage has been applied to the controller. This is usually caused by a
poor battery connection. Check the battery connections.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 37 -
 PM SHEET

CUSTOMER & MACHINE INFORMATION

Customer: Email:

Address: Phone:

City: State: Zip: Contact:

Serial #: Model #: Work Order #:

NOTE: Start with Machine filled at least with ½ Tank of water. Turn ON Machine and Test Functionality of Machine

CHECK OPERATION & CONDITION OF IN SPEC REPAIR PROBLEM

Key Switch
Battery Gauge
Deck Up / Down – Brush Switch
Brush Pressure +/- Toggle (Optional)
Vacuum Switch - ON / OFF
Squeegee Lever - Up/Down
Solution Switch - ON/OFF
Solution Flow Lever +/-
Green Drive Buttons - L & R
Reverse Toggle Switch
E-Stop (Optional)

NOTE: Drain Solution & Recovery Tank fully. Rinse out Recovery Tank

CLEAN & INSPECT – SOLUTION TANK IN SPEC REPAIR PROBLEM

Solution Fill Screen - Mesh
Solution Fill Hose (Optional)
Solution Inline Filter
Vacuum Muffler Drain Hose
Battery Drain Hose

BRUSH CONDITION – SCRUB DECK

Deck Curtains/Wipers Good Worn Needs Replacement
Brush Sockets: (2-Disk)/(4-Cylindrical) Good Worn Needs Replacement
Brush Drivers: (2-Disk)/(4-Cylindrical) Good Worn Needs Replacement
Scrub Brush Fiber Length Brush 1 Length: Brush 2 Length: Rotated Brushes: Y / N

CLEAN & INSPECT – SCRUB DECK IN SPEC REPAIR PROBLEM

Scrub Deck Linkage Pivot Points
Scrub Deck Lift Actuator
Scrub Deck Level (Orbital Only)
Scrub Motor Wires

CLEAN & INSPECT - SQUEEGEE IN SPEC REPAIR PROBLEM

Remove and Wipe off Squeegee
Check and Rotate Blades as Needed
Caster Wheels and Height
Pitch Adjust
Check Pivot and Knobs
Squeegee Vac Hose

CLEAN & INSPECT – RECOVERY TANK IN SPEC REPAIR PROBLEM

Recovery Tank Lid & Gasket
Vacuum Float Ball Screen
Vacuum Box White Filter
solution Site Tube

CLEAN & INSPECT – DRIVE IN SPEC REPAIR PROBLEM

Drive Wheels & Casters Condition
Grease Caster Swivel

RPS Corporation © 2021

- 38 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 PM SHEET

BATTERY HYDROMETER WATER CLARITY WATER LEVEL

#1 READING (Circle One) (Circle One)
Cell A Clear Dark Overfilled OK Low

Cell B Clear Dark Overfilled OK Low

Cell C Clear Dark Overfilled OK Low

Cell D/2A Clear Dark Overfilled OK Low

Cell E/2B Clear Dark Overfilled OK Low

Cell F/2C Clear Dark Overfilled OK Low

BATTERY HYDROMETER WATER CLARITY WATER LEVEL
#2 READING (Circle One) (Circle One)
Cell A Clear Dark Overfilled OK Low

Cell B Clear Dark Overfilled OK Low

Cell C Clear Dark Overfilled OK Low

Cell D/4A Clear Dark Overfilled OK Low

Cell E/4B Clear Dark Overfilled OK Low

Cell F/4C Clear Dark Overfilled OK Low

CLEAN & INSPECT - BATTERIES IN SPEC REPAIR PROBLEM
Battery Terminals
Battery Cables
Torque Battery Nuts 11ft/lbs

OPERATE & CONFIRM IN SPEC REPAIR PROBLEM

Fill Solution Tank – ¾ Full
Scrub & Dry
Fine Tune Squeegee Adjustments

COMMENTS & RECOMMENDATIONS

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

________________________________________________________________________________________________

Servicing Distributor:

Technician’s Name: Date: Signature:

Customer’s Name: Date: Signature:

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 RPS Corporation © 2021 - 39 -

 MEMBRANE/TOUCH SCREEN ERROR CODES
Membrane Touch
Panel screen Error Type Description Action Remedy
Code Code

The machine is disabled

Incompatable options Check programming op-
hard/ or continues operating
10 100A Bad Personality programmed or a check- tions and/or reprogram
soft with factory default pa-
sum failure EEPROM
rameters
Throttle is engaged at Machine remains in a
power up preventing a pre-idle condition until Take your foot off the
11 110A Initial throttle fault soft
successful return to idle the active throttle condi- gas
state tion goes away
12 120A hard
The machine is disabled
An error was detected Cycle keyswitch. If prob-
hard/ or continues operating
13 130A Memory fault during an EEPROM read lem persists change
soft with factory default pa-
access control board
rameters
The battery voltage has
Charge or replace bat-
14 140A Dead battery hard dropped below NN.n The machine is disabled
teries
Volts
The battery voltage has
dropped below NN.n All but the transport
Low battery
15 150A soft Volts and all but the motor are disabled is Charge battery
charge
transport motor have disabled
been disabled
Keyswitch off, wait ten
The microcontroller
The controller is minutes, keyswitch
16 160A Overheat CPU hard hardware has had an
switched off on. If problem persists
over temperature failure
change control board
17 170A
An abnormally high idle
Transport idle cur- current has been detect-
18 180A hard The machine is disabled
rent fault ed in the transport mo-
tor (operational motor)
An abnormally high idle
Brush, deck actuator
Brush idle current current has been detect-
19 190A soft and water/suds are dis-
fault ed in the brush motor
abled
(operational motor)
An abnormally high idle
Vacuum idle cur- current has been detect- Vacuum motor is dis-
20 200A soft
rent fault ed in the vacuum motor abled
(operational motor)
An abnormally high idle
Squeegee idle cur- current has been detect- Squeege motor is dis-
21 210A soft
rent fault ed in the squeegee mo- abled
tor (operational motor)
22 220A soft
Keyswitch off, wait ten
The main traction relay
Transport motor seconds, keyswitch
23 230A hard was detected closed The machine is disabled
relay not open on. If problem persists
during power on
change control board
The main traction relay
Transport motor was detected open after
24 240A hard The machine is disabled
relay not closed being energized during
power on
An illegal voltage has
Check throttle action
25 250A Throttle fault hard been read from the The machine is disabled
and voltages
throttle feedback circuit
An illegal voltage has
26 260A Brake fault hard been read from the The machine is disabled
brake feedback circuit
27 270A Alarm fault soft
Auxilliary output 1
28 280A soft
fault
Auxilliary output 2
29 290A soft
fault
Auxilliary output 3
68 680A soft
fault
An abnormally high idle
Brush, deck actuator
Deck actuator idle current has been detect-
30 300A soft and water/suds are dis-
current over limit ed in the deck actuator
abled
motor

- 40 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MEMBRANE/TOUCH SCREEN ERROR CODES
Membrane Touch
Panel screen Error Type Description Action Remedy
Code Code

An energized transport motor is

31 310A Transport motor stalled hard
not rotating
Transport motor circuit There is excessive current in the
32 320A hard
current over limit transport motor drive circuit
Transport motor circuit There is excessive current in the
33 330A hard The machine is disabled
current over limit transport motor drive circuit
Brush motor current The brush motor current has Brush, deck actuator and water/
34 340A soft
over software limit exceed the software limit suds are disabled
The brush motor current has
Brush motor current Brush, deck actuator and water/
35 350A soft exceed the absolute hardware
over hardware limit suds are disabled
limit
An electrically open condition
Open circuit detected Brush, deck actuator and water/
36 360A soft has been detected in the brush
in brush motor suds are disabled
motor circuit
37 370A
38 380A
39 390A
The transport motor current has
Transport motor cur-
40 400A hard exceed the absolute hardware The machine is disabled
rent over hardware limit
limit
The transport motor current has
Transport motor cur-
41 410A hard exceed the absolute hardware The machine is disabled
rent over hardware limit
limit
42 420A
12VDC power supply The 12VDC supply voltage is
43 430A outside acceptable hard less tha 11.75V or greater than The machine is disabled check batteries
limits 12.25 volts
44 440A
Deck actuator motor
The deck actuator current has Brush, deck actuator and water/
45 450A current over software soft
exceed the software limit suds are disabled
limit
Vacuum motor current The vacuum motor current has
46 460A soft The vacuum motor is disabled
over hardware limit exceed the software limit
Deck actuator motor The deck actuator current has
Brush, deck actuator and water/
47 470A current over hardware soft exceed the absolute hardware
suds are disabled
limit limit
Squeegee motor cur- The squeegee motor current The squeege actuator is dis-
48 480A soft
rent over software limit has exceed the software limit abled
Vacuum motor current The vacuum motor current has
49 490A soft The vacuum motor is disabled
over software limit exceed the software limit
The sueegee motor current has
Squeegee motor cur- The squeege actuator is dis-
50 500A soft exceed the absolute hardware
rent over hardware limit abled
limit
51 510A
52 520A Open circuit detected soft An electrically open condition The vacuum motor is disabled
in vacuum motor has been detected in the vacu-
um motor circuit
53 530A
54 540A
55 550A Open circuit detected soft An electrically open condition Brush, deck actuator and water/
in deck actuator has been detected in the deck suds are disabled
actuator circuit
56 560A
23 570A Transport motor relay hard The main traction relay was de- The machine is disabled Keyswitch off, wait ten sec-
not open tected closed during power on onds, keyswitch on. If problem
persists change control board
23 580A Transport motor relay hard The main traction relay was de- The machine is disabled Keyswitch off, wait ten sec-
not open tected closed during power on onds, keyswitch on. If problem
persists change control board
59 590A Squeegee motor soft An energized squeegee actuator The squeegee actuator is dis-
stalled is not moving abled
60 600A Deck actuator stalled soft An energized deck actuator is Brush, deck actuator and water/
not rotating suds are disabled
61 610A
62 620A Brush motor stalled soft An energized brush motor is not Brush, deck actuator and water/
rotating suds are disabled
63 630A vacuum motor stalled soft An energized vacuum motor is The vacuum motor is disabled
not rotating
64 640A
65 650A
66 660A Overheat MOSFET hard The transport motor drive circuit The machine is disabled
has had an over temperature
failure
67 670A Battery over voltage hard The battery voltage is above The machine is disabled check batteries / wiring
acceptable limits

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 41 -
 TOUCH SCREEN SCHEMATICS

- 42 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MILITARY GRADE SCHEMATIC

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 43 -
 5 4 3 2 1

MEMBRANE PANEL DISPLAY PIN OUTS CONTROLLER PIN OUTS

- 44 -
MOLEX 4 PIN: MOLEX 20 PIN:
1 - DGND 8 - ON/OFF REF (B+)
2 - CAN H 9 - THROTTLE LO REF
2 1 RED 3 - CAN L 10 - THROTTLE WIPER
4 3 YELLOW 4 - KEY SWITCH IN 11 - VACUUM CLOG INPUT
13 - REVERSE SELECT INPUT
MOLEX 4 PIN MOLEX 4 PIN: 15 - INHIBIT INPUT
ORANGE 1 - DGND 17 - BACK UP ALARM OUTPUT
GREEN 2 - CAN H 18 - ON/OFF INPUT (KSI)
19 - LO SWITCH REF 0V
20 - THROTTLE HI REF
2 1
D D
MOLEX 14 PIN:
MOLEX 2 PIN 1 - AUXILIARY SUPPLY
390-2328 2 - SOLUTION OUTPUT
RED #35 3 - SQUEEGEE ACTUATOR OUTPUT
4 - DECK ACTUATOR OUTPUT
BLUE #103 6 - ZERO3 INPUT
8 - AUXILIARY SUPPLY
9 - SOAP PUMP OUTPUT
SW, RECOVERY TANK FULL 10 - SQUEEGEE ACTUATOR OUTPUT
175-2590 11 - DECK ACTUATOR OUTPUT
USB CHARGE PORTS

170-4500
RED 35 BLACK #72 1 2 ORANGE #71
S
290-9620 BLK 20
SOLENOID VALVE, SOLUTION
1 2 RED #202 PINK #130 1 2
ORANGE #71
SW, KEY ON-OFF
MEMBRANE SCHEMATICS

MOTOR, DECK ACTUATOR

175-0300 WHITE #131
150-2830

YELLOW #201
YELLOW #201 1
WHITE #260 2
RED #202 3 BLK/WH #261
SW, EMERGENCY STOP-SPST NC
4
253-8500 5 7-292
C 1 6 POTENTIOMETER C
BLACK #75 1 2 GREEN #74 8 1 2 1 3
S 9 2 3 SWITCH, REVERSE
10 3 4

2
11 4
SOLENOID PUMP, SUDS 12 5 MOLEX 4 PIN
13 6 7-229
170-8500 14 7 11 1

BLK #233

WHITE #234
RED #38 BLACK #39 BLK #233
GREEN #232

12 2 1 2
MOLEX 14 PIN 13 3
HEATER, FREEZER PACKAGE 2 1 14 4 SWITCH, HANDLEBAR
15 5
MOLEX 2 PIN 16 6
17 7
18 8 7-229
390-9631 19 9
RED #30 20 10 1 2

370-9619 CIRCUIT BREAKER 15 AMP MOLEX 20 PIN SWITCH, HANDLEBAR

RED #182 1 2 RED #183

390-9632 370-2930
SW, SPRAY JET PUMP BLACK #29
RED #170 1
CIRCUIT BREAKER 15 AMP BLACK #171 2

BLACK #31
MOTOR, VACUUM BACK UP ALARM
5-293
RED #30 4 1 1 2
5-891 3
B RED #202 1 B
2 1

VACUUM
RED #183 1 2 BLACK #184
RELAY, BUSS

MOTOR, SCRUB
MOTOR, SPRAY JET
1 1 2

ORANGE #105

PURPLE #270
BLK/WH #271
YELLOW #23
1
BRUSH
MOTOR, SCRUB

1 2 GREEN #106 1 2

CONTROLLER
BATTERY 6V 1
BATTERY DISCONNECT
MOTOR, SQUEEGEE ACTUATOR
1
BATTERY

5-260
5-260
CHARGER, DELTA Q BATTERY 6V
MOTOR, TRACTION DRIVE
CHARGER INHIBIT N.C. BLK/WH #271
PURPLE #270 1 1 2
21-2330
SW, INHIBIT
BATTERY 6V 1
TRACTION

A A

BATTERY 6V

Title
Walk Behind Membrane Panel
Size Document Number Rev
A
Date: Thursday, January 25, 2024 Sheet 1 of 1
5 4 3 2 1

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 5 4 3 2 1

MEMBRANE PANEL DISPLAY PIN OUTS CONTROLLER PIN OUTS

MOLEX 4 PIN: MOLEX 20 PIN:
1 - DGND 8 - ON/OFF REF (B+)
2 - CAN H 9 - THROTTLE LO REF
2 1 RED 3 - CAN L 10 - THROTTLE WIPER
4 3 YELLOW 4 - KEY SWITCH IN 11 - VACUUM CLOG INPUT
13 - REVERSE SELECT INPUT
MOLEX 4 PIN 15 - INHIBIT INPUT
ORANGE 17 - BACK UP ALARM OUTPUT
GREEN 18 - ON/OFF INPUT (KSI)
19 - LO SWITCH REF 0V
20 - THROTTLE HI REF
2 1 BLUE
D D
MOLEX 14 PIN:
MOLEX 2 PIN 1 - AUXILIARY SUPPLY
390-2328 BLACK 2 - SOLUTION OUTPUT
RED #35 3 - SQUEEGEE ACTUATOR OUTPUT
4 - DECK ACTUATOR OUTPUT
BLUE #103 6 - ZERO3 INPUT
8 - AUXILIARY SUPPLY
9 - SOAP PUMP OUTPUT
SW, RECOVERY TANK FULL 10 - SQUEEGEE ACTUATOR OUTPUT
175-2590 11 - DECK ACTUATOR OUTPUT
USB CHARGE PORTS

RED 35

290-9621 BLK 20 BLACK #72

1 2 RED #202 PINK #130 1 2 ORANGE #71

SW, KEY ON-OFF RED #345

MOTOR, DECK ACTUATOR
175-0300 WHITE #131
150-2830

YELLOW #201
YELLOW #201 1
WHITE #260 2
RED #202 3 BLK/WH #261
SW, EMERGENCY STOP-SPST NC
4
253-8500 5 7-292
C 1 6 POTENTIOMETER C
BLACK #75 1 2 GREEN #74 8 1 2 1 3
S 9 2 3 SWITCH, REVERSE
10 3 4

2
11 4
SOLENOID PUMP, SUDS 12 5 MOLEX 4 PIN ZERO3 SINGLE LINE
13 6 7-229
170-8500 14 7 11 1

BLK #233

WHITE #234
RED #38 BLACK #39 BLK #233
GREEN #232

12 2 1 2
MOLEX 14 PIN 13 3
HEATER, FREEZER PACKAGE 2 1 14 4 SWITCH, HANDLEBAR
15 5 123-2335

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
MOLEX 2 PIN 16 6 5-270 BLACK
17 7 BLACK 1 2 #373
18 8 7-229
390-9633 19 9 DIODE ZERO3
RED #30 20 10 1 2

370-9620 CIRCUIT BREAKER 15 AMP MOLEX 20 PIN SWITCH, HANDLEBAR

RED #182 1 2 RED #183 123-2335

390-9634 370-2930 5-270
SW, SPRAY JET PUMP BLACK #29 RED #370 1 2 BLACK
RED #170 1
CIRCUIT BREAKER 15 AMP BLACK #171 2 DIODE ZERO3

BLACK #31
MOTOR, VACUUM BACK UP ALARM
5-293 170-4500
RED #30 4 1 1 2 PURPLE #360 1 2 BLACK #361
5-891 3 S
B RED #202 1 B
2 1 SOLENOID VALVE, ZERO3

VACUUM
RED #183 1 2 BLACK #184
RELAY, BUSS

MOTOR, SCRUB 123-8910

MOTOR, SPRAY JET
1 1 2 YELLOW #350 1 2 BLACK #351

ORANGE #105
MOTOR, ZERO3 PUMP

PURPLE #270
BLK/WH #271
YELLOW #23
BRUSH 1

MOTOR, SCRUB

1 2 GREEN #106 1 2

CONTROLLER
BATTERY 6V 1 290-9581
BATTERY DISCONNECT YELLOW #350 1 2 YELLOW #350
MOTOR, SQUEEGEE ACTUATOR
1 RESISTOR 8 OHM 50 WATT
BATTERY

5-260

5-260
CHARGER, DELTA Q BATTERY 6V
MOTOR, TRACTION DRIVE 5-293
CHARGER INHIBIT N.C. BLK/WH #271 RED #345 4
PURPLE #270 1 1 2 3 RED #341
21-2330 BLUE 1
SW, INHIBIT BLACK 2
BATTERY 6V 1
RELAY, ZERO3
TRACTION

A A
349-9604
RED #340 RED 341
BATTERY 6V
CIRCUIT BREAKER 4 AMP

Title
Walk Behind Membrane Panel Zero3
Size Document Number Rev
A
Date: Thursday, January 25, 2024 Sheet 1 of 1
MEMBRANE PANEL (ZERO3 ®)

5 4 3 2 1

- 45 -
LEGACY SCHEMATIC

- 46 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MACHINE DECALS

Central Command Decals

Military Grade Legacy Membrane/Touch Screen

24 24

24

A C
MAX

B B

A C
C A A C

B B
MIN

B B

C A
C A

175-2021 175-2023 175-2023

175-2021

Part #:175-2021 Part #:175-2020 Part #:175-2023

Models / Options / Squeegee Size Decals

Part #:175-1523

Part #:164-1515 Part #:370-7215 Part #:175-1521

Part #:123-1837
Part #:175-1515 Part #370-7214

Part #:123-1838

Part #:264-1515 Part #:370-7219

94cm 0 45
-16
02
Part #:123-1843

Part #:33-1602 Part #:37-1602 Part #:41-1602 Part #:45-1602

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 47 -
 MICRO-HD COMMON WEAR PARTS

ROUND DISK BRUSHES: ROUND DISK PADS:

NOTICE NOTICE
The ## in Disk Column Denotes Desk Pad Size: 13'' or The ## in Disk Column Denotes Desk Pad Size: 13'' or
20'' 20''

BRUSHES DISK LEVEL DISK PADS DISK LEVEL COLOR

Super Grit ##-382SS Very High Super Black ##-422BB Very High Black
Tough Grit ##-382S High Black ##-422B High Black
Midi Grit ##-382C Medium Brown ##-422BR High Brown
Light Grit ##-382PS Moderate Green ##-422G Medium Green
Poly ##-382P Light Blue ##-422BL Moderate Blue
Nylon ##-382N Light Red ##-422R Moderate Red
Tampico ##-382T Light White ##-422W Light White
Pad Driver ##-382D
Diamond Driver ##-382DD

CYLINDRICAL BRUSHES:
BRUSHES MODEL 25'' LEVEL
CYLINDRICAL
Tough Grit 236-697S High
Midi Grit 236-697C Medium
Light Grit 236-697PS Moderate
Nylon 236-697N Light
Tampico 236-697T Light
EDGE PADS AND SCREENS:
DESCRIPTION 24''×14'' 20''×14'' 28''×14''
SCRUBDECK SCRUBDECK SCRUBDECK
White Pad N/A EDGE-4005 EDGE-4054
Red Pad EDGE-2404 EDGE-4004 EDGE-4053
Blue Pad EDGE-2403 EDGE-4003 EDGE-4052
Green Pad EDGE-2402 EDGE-4002 EDGE-4051
Black Pad EDGE-2401 EDGE-4001 EDGE-4050
White Driver Pad N/A EDGE-4025 EDGE-4058
Tile/Grout Renovator Pad N/A EDGE-4018 EDGE-4059
Microfiber Pad N/A EDGE-4036 EDGE-4060
Dominator HD Strip Pad N/A EDGE-4006 EDGE-4061
Maroon ECO Prep Pad EDGE-2407 EDGE-4007 EDGE-4062
Remover Burnishing Pad N/A EDGE-4008 EDGE-4063
Porko Burnishing Pad N/A EDGE-4017
Velcro Pad N/A 300-4023

- 48 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MICRO-HD COMMON WEAR PARTS

EDGE GRIP FACE:

DESCRIPTION PART#
20'', 24'' & 28'' Mighty Lok Grip Face 300-
01037Z

V2.1 SQUEEGEE BLADE KITS & COMPLETE SQUEEGEE ASSEMBLIES:

SQUEEGEE 20'' DISK 26'' DISK 25'' CYL. 20'' EDGE 24'' EDGE 28'' EDGE
SIZE DECKS DECKS DECKS DECKS DECKS DECKS
33'' Squeegee Standard Standard Standard Standard Standard Standard
37'’ Squeegee Optional Optional Optional Optional Optional Optional

SQUEEGEE LINATEX BLADE COMPLETE

SIZE KIT SQUEEGEE
ASSEMBLIES

33'' Squeegee 433-721L 233-2181

37'' Squeegee 437-721L 237-2181

SQUEEGEE MATERIAL: USED FOR:

Provides best wear and tear resistance. Not
LINATEX
designed for use with harsh chemicals.

NOTICE NOTICE
Squeegee blade kits include (1) Rear Blade, (1) Front Squeegee Assemblies (complete) listed above all
Blade, and (2) Caster Wheels with hardware. come with Linatex blades.

NOTICE
Size is shown as a decal at the top of the steel
squeegee body on all squeegee's.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 49 -
 MINI-HD COMMON WEAR PARTS
ROUND DISK BRUSHES: ROUND DISK PADS:

NOTICE NOTICE
The ## in Disk Column Denotes Desk Pad Size: 13'' or The ## in Disk Column Denotes Desk Pad Size: 13'' or
14'' 14''

BRUSHES DISK LEVEL DISK PADS DISK LEVEL COLOR

Super Grit ##-382SS Very High Super Black ##-422BB Very High Black
Tough Grit ##-382S High Black ##-422B High Black
Midi Grit ##-382C Medium Brown ##-422BR High Brown
Light Grit ##-382PS Moderate Green ##-422G Medium Green
Poly ##-382P Light Blue ##-422BL Moderate Blue
Nylon ##-382N Light Red ##-422R Moderate Red
Tampico ##-382T Light White ##-422W Light White
Pad Driver ##-382D
Diamond Driver ##-382DD

CYLINDRICAL BRUSHES:
BRUSHES MODEL 25'' MODEL 29'' LEVEL
CYLINDRICAL CYLINDRICAL
Tough Grit 236-697S 276-697S High
Midi Grit 236-697C 276-697C Medium
Light Grit 236-697PS 276-697PS Moderate
Nylon 236-697N 276-697N Light
Tampico 236-697T 276-697T Light

EDGE PADS AND SCREENS:

DESCRIPTION 24''×14'' 28''×14''

SCRUBDECK SCRUBDECK
White Pad N/A EDGE-4054
Red Pad EDGE-2404 EDGE-4053
Blue Pad EDGE-2403 EDGE-4052
Green Pad EDGE-2402 EDGE-4051
Black Pad EDGE-2401 EDGE-4050
White Driver Pad N/A EDGE-4058
60 Grit Sand Screen N/A EDGE-4059
80 Grit Sand Screen N/A EDGE-4060
100 Grit Sand Screen N/A EDGE-4061
120 Grit Sand Screen N/A EDGE-4062
150 Grit Sand Screen N/A EDGE-4063
80 Grit Sand Paper N/A N/A
100 Grit Sand Paper N/A N/A
400 Grit Diamond Polishing Pad N/A EDGE-4013
800 Grit Diamond Polishing Pad N/A EDGE-4014

- 50 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MINI-HD COMMON WEAR PARTS

1500 Grit Diamond Polishing Pad N/A EDGE-4015

3000 Grit Diamond Polishing Pad N/A EDGE-4016
6000 Grit Diamond Polishing Pad N/A EDGE-4070
Tile/Grout Renovator Pad N/A EDGE-4048
Dominator HD Strip Pad N/A EDGE-4055
Maroon ECO Prep Pad EDGE-2407 EDGE-4056
EDGE GRIP FACE:
DESCRIPTION PART#
24''-28'' Mighty Lok Grip Face 300-
01037Z

V2.1 SQUEEGEE BLADE KITS & COMPLETE SQUEEGEE ASSEMBLIES:

SQUEEGEE 26'' DISK 28'' DISK 25'' CYL. 29'' CYL. 24'' EDGE 28'' EDGE
SIZE DECKS DECKS DECKS DECKS DECKS DECKS
37'' Squee- Standard Standard Standard Standard Standard Standard
gee
41'' Squee- Optional Optional Optional Optional Optional Optional
gee

SQUEEGEE LINATEX BLADE COMPLETE

SIZE KIT SQUEEGEE
ASSEMBLIES
37'' Squee- 437-721L 37-2181
gee
41'' Squee- 441-721L 41-2181
gee

SQUEEGEE MATERIAL: USED FOR:

Provides best wear and tear resistance. Not
LINATEX
designed for use with harsh chemicals.

NOTICE NOTICE
Squeegee blade kits include (1) Rear Blade, (1) Front Squeegee Assemblies (complete) listed above all
Blade, and (2) Caster Wheels with hardware. come with Linatex blades.

NOTICE
Size is shown as a decal at the top of the steel
squeegee body on all squeegee’s.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 51 -
 MAG-HD COMMON WEAR PARTS

ROUND DISK BRUSHES: ROUND DISK PADS:

NOTICE NOTICE
The ## in Disk Column Denotes Desk Pad Size: 15'', The ## in Disk Column Denotes Desk Pad Size: 15'',
16'' or 17'' 16’’ or 17''

BRUSHES DISK LEVEL DISK PADS DISK LEVEL COLOR

Super Grit ##-382SS Very High Super Black ##-422BB Very High Black
Tough Grit ##-382S High Black ##-422B High Black
Midi Grit ##-382C Medium Brown ##-422BR High Brown
Light Grit ##-382PS Moderate Green ##-422G Medium Green
Poly ##-382P Light Blue ##-422BL Moderate Blue
Nylon ##-382N Light Red ##-422R Moderate Red
Tampico ##-382T Light White ##-422W Light White
Pad Driver ##-382D
Diamond Driver ##-382DD

CYLINDRICAL BRUSHES:
BRUSHES MODEL 29'' MODEL 33'' LEVEL
CYLINDRICAL CYLINDRICAL
Tough Grit 276-697S 316-697S High
Midi Grit 276-697C 316-697C Medium
Light Grit 276-697PS 316-697PS Moderate
Nylon 276-697N 316-697N Light
Tampico 276-697T 316-697T Light
EDGE PADS AND SCREENS:
DESCRIPTION 28''×14'' SCRUBDECK 32''×14'' SCRUBDECK
White Pad EDGE-4054 EDGE-5005
Red Pad EDGE-4053 EDGE-5004
Blue Pad EDGE-4052 EDGE-5009
Green Pad EDGE-4051 EDGE-5002
Black Pad EDGE-4050 EDGE-5001
White Driver Pad EDGE-4058 N/A
60 Grit Sand Screen EDGE-4059 N/A
80 Grit Sand Screen EDGE-4060 N/A
100 Grit Sand Screen EDGE-4061 EDGE-5028
120 Grit Sand Screen EDGE-4062 EDGE-5029
150 Grit Sand Screen EDGE-4063 N/A
Tile/Grout Renovator Pad EDGE-4048 N/A
Dominator HD Strip Pad EDGE-4055 N/A
Maroon ECO Prep Pad EDGE-4056 EDGE-5007
Remover Burnishing Pad EDGE-4057 EDGE-5008
Porko Burnishing Pad EDGE-4047 N/A
Velcro Pad 300-4024 N/A

- 52 - FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016
 MAG-HD COMMON WEAR PARTS

EDGE GRIP FACE:

DESCRIPTION PART#
28''-32'' Mighty Lok Grip Face 300-
01037Z

V2.1 SQUEEGEE BLADE KITS & COMPLETE SQUEEGEE ASSEMBLIES:

SQUEEGEE 30'' DISK 34'' DISK 29'' CYL. 33'' CYL. 28'' EDGE 32'' EDGE
SIZE DECKS DECKS DECKS DECKS DECKS DECKS
41'' Squee- Standard Optional Standard Optional Standard Optional
gee
45'' Squee- Optional Standard Optional Standard Optional Standard
gee

SQUEEGEE LINATEX BLADE COMPLETE

SIZE KIT SQUEEGEE
ASSEMBLIES
41'' Squee- 441-721L 41-2181
gee
45'' Squee- 445-721L 45-2181
gee

SQUEEGEE MATERIAL: USED FOR:

Provides best wear and tear resistance. Not
LINATEX
designed for use with harsh chemicals.

NOTICE NOTICE
Squeegee blade kits include (1) Rear Blade, (1) Front Squeegee Assemblies (complete) listed above all
Blade, and (2) Caster Wheels with hardware. come with Linatex blades.

NOTICE
Size is shown as a decal at the top of the steel
squeegee body on all squeegee's.

FC-WALK-BEHIND-V2-SERIES-OP-EN V24.016 - 53 -
1711 South Street
Racine, WI 53404
www.tomcatequip.com
1-262-681-3583

© RPS Corporation 2024, All Rights Reserved.