635464004502

CMY12-1 Series Mirror Lights

WAROM TECHNOLOGY INCORPORATED COMPANY

 CMY12-1 Series Mirror Lights Table 1
I. Overview Protect
1. Nomenclature Rated Rated Light Lamp Weig
Model ion Cable inlet
voltage V power source type holder ht kg
CMY 12-1 level
Power 5W×1 1.5
Design No. 7W×1
1.5
Fluorescent mirror lights 7W×1-SU LED T5
2.Scope of application 9W×1
1.8
CMY12-1 series mirror lights are suitable for bathroom mirrors, bedside and 220V 9W×1-SU
hole,
240V AC
other areas. 18W×1 suitable
CMY12-1 50/60Hz IP44
3. Working environment Fluorescent 2 for
110/120V 18W×1-S
AC 60Hz U
cable
3.2 Marine environment of humid air, salt spray, oil mist and mold; G13
36W×1
3.3 Can withstand the normal vibration and shock of the ship, and is suitable
tubes 3.9
for marine environment; 36W×1-S

3.4 Ambient temperature: -25°C~+55°C. U

II. The main technical parameters are shown in Table 1

NOTE: SU indicates that lights equipped with socket
III. Structural characteristics
The mirror light is composed of an enclosure, a transparent cover and internal
electrical components;
a. The enclosure is made of galvanized steel, the surface is sprayed with white
plastic powder, and stainless steel material is optional;
b. The transparent cover is milky white acrylic, PC material is optional;
c. The light source is configured with LED module;
d. Optional emergency centralized power supply;
e. Optional socket.
IV. Installation and usage
1. The installation of lamps must be carried out by professional licensed
-1- -2-
personnel; terminal blocks in order and the internal clearance should be checked out;
2. Before installation, check whether the parameters listed on the nameplate of f. After checking that the power supply is connected correctly, install the
the lamp are consistent with the actual conditions. Do not open the transparent transparent cover and side cover back on the enclosure in turn, and then
cover and disassemble other parts casually to ensure the sealing performance; tighten the fastening bolts.
3. Thread the cable through the inlet and the sealing ring must be put on, g Connect the external grounding wire, and the cross-sectional area of the
connect the terminal inside the enclosure reliably, and connect the grounding external grounding wire should not be less than 4mm2.
wire. The tightening torque is 3.2N.m, and the wire stripping length is 7~8mm, 5. When installing and using this product, it is necessary to consider the use
as shown in the figure below: environment of the PC parts and the chemical substances they are exposed to
to avoid the damage that comes from contact with the media that has an
erosive effect on the PC.

V. Use and maintenance

4. When wiring, please follow: Lamps should be regularly maintained and repaired in time during use!
a. Use a screwdriver to unscrew the screws on the side covers at both ends of 1. After the installation of the lamp, check whether the insulation
the lamp and remove the side covers and transparent covers, and then use a resistance between the terminal and the enclosure is normal before
screwdriver to remove the light source mounting plate assembly inside the powering up;
housing. 2. When opening the lamp, you must turn off the power before opening
b. There are two cable inlets on the back of the enclosure, the lamp is equipped the cover according to the requirements of the warning board;
with built-in terminal blocks, select cables that meet the requirements, put on a 3. Regularly check whether the sealing ring is aging to ensure the sealing
sealing ring, and pass the cable through the cable entry device; performance; If water is found inside the lamp, please check whether the
c. After the cables pass through the entry device, it should be connected with sealing ring is effectively pressed;
the terminal block, the inner grounding wire should be connected at the same 4. The transparent cover should be cleaned regularly to ensure the
time, and ensure that the electrical gap between the exposed part of the wire illumination;
and the enclosure is not less than 3mm; 5. Check whether the connection is firmly connected regularly to ensure
d. Please refer to the wiring diagram for wiring, it is strictly forbidden to electrical conductivity;
change the wiring method without authorization; 6. On-site users should understand the performance of lamps, and if they
e. Power cable conductors L, N, and PE should be reliably connected with the find abnormal phenomena, they should cut off the power supply for repair,
-3- -4-
non-full-time maintenance personnel are not allowed to carry out 14. After the product exceeds the use period or cannot work normally after
maintenance without authorization; maintenance, it cannot be discarded at will, please hand it over to an
7. Regularly remove dust and dirt on the lamp enclosure to improve the enterprise with waste electrical and electronic product disposal
luminous efficiency and heat dissipation performance of the lamp. When qualifications.
cleaning, the power must be cut off. Please wipe the enclosure and
VI. The appearance and installation dimensions are shown in Table 2
transparent cover with a damp fiberless cloth or sponge to prevent static
Table 2
electricity;
Dimensions
8. Check whether the transparent parts have been affected by foreign Rated power
H L W1 W A
objects, and whether the installation accessories are loose, desoldered, 5W×1 107 355 62 212
corroded, etc. If there is, it should be suspended and repaired or replaced 7W×1 107 355 62 212

in time; 7W×1-SU 107 355 67 212

9. After opening the cover, it should be checked whether the rubber seal is 9W×1 107 486 62 370
9W×1-SU 107 486 67 370
hard or sticky, whether the wire insulation layer is green or carbonized,
18W×1 107 637 62 521
and whether the insulation and electrical components are deformed or
18W×1-SU 107 637 67 521
scorched. If these are found, they should be repaired and replaced in time;
36W×1 107 1247 62 1131
10. The model, specification, size and performance of the light source,
36W×1-SU 107 1247 67 1131
parts and electrical components after maintenance and replacement should
be completely consistent with those before maintenance and replacement;
11. When closing the cover, make sure the sealing ring plays its role in the
original position;
12. The sealing part of the lamp should not be disassembled and opened
frequently; The product warranty period is generally one year according to
the provisions of the National Product Three Guarantees Law, and the
contract stipulates otherwise;
13. The content of restricted substances in products is below the limit
requirements specified in standard;

-5- -6-
VII. The storage environmental conditions are shown in Table 3
Table 3
Ambient temperature -25°C +55°C
Relative humidity (when ambient temperature is 25°C)

VIII. Precautions for unpacking and inspection

1. Check whether there is any appearance damage during transportation, such
as product deformation, etc.;
2. The packaging box contains this product and its instruction manual, product
certificate.
IX. Ordering instructions
When ordering, please specify the product name, model, quantity and
other parameters.
All parameters are subject to change due to product improvement
without further notice!

-7- -8-