Scribd
Upload
27 views

Principle_of_Operation-Motion_Sensor-Knowledge_Base_PASCO

The PASCO motion sensors utilize ultrasonic pulses at approximately 49.4 kHz to measure distances by calculating the time taken for emitted pulses to return after reflecting off surfaces. The sensor has a dead time of 0.85 ms, limiting its ability to measure distances under 15 cm, and features adjustable sensitivity settings for different range measurements. Technical details include specific signal protocols and connections for the CI-6742 Motion Sensor II, with support available through various contact methods.

Uploaded by

lure-harmful-fog
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views

Principle_of_Operation-Motion_Sensor-Knowledge_Base_PASCO

The PASCO motion sensors utilize ultrasonic pulses at approximately 49.4 kHz to measure distances by calculating the time taken for emitted pulses to return after reflecting off surfaces. The sensor has a dead time of 0.85 ms, limiting its ability to measure distances under 15 cm, and features adjustable sensitivity settings for different range measurements. Technical details include specific signal protocols and connections for the CI-6742 Motion Sensor II, with support available through various contact methods.

Uploaded by

lure-harmful-fog
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Principle of Operation - Motion Sensor - Knowledge Base

Technote: How do the PASCO motion sensors work?

The PASCO motion sensors use ultrasonic pulses to determine distance to the surface of reflection. Specifically, by emitting a train of 16 square wave pulses
at a sound frequency of about 49.4 kHz and detecting their echoes. The distance d is calculated from d = v (t-t0) /2 , where v is the local velocity of
sound, t0 is a small correction for electronic delays, and t is the round-trip time interval between the emitted pulse train and the returning pulse train. There
is a dead time of about 0.85 ms, where the sensor will not detect a return, which accounts for the inability of the sensor to measure distances of less than 15
cm.

Changing the range setting of the motion sensor adjusts the sensitivity of the receiver to pulses. On the "far" setting, the receiver is less sensitive to return
pulses than on the "near" setting. (On PASPORT and ScienceWorkshop models this is a physical switch on the sensor; on the Wireless Motion the range
setting can be changed in the software).

CI-6742 Specific Technical Details


The signal to and from the Motion Sensor II are normally both high (5 V). To initiate a sensor cycle, the trigger signal is held low (0 V) for about 0.13
milliseconds. This then causes the return echo signal to also go low. A series of ultrasonic pulses are then emitted by the Motion Sensor II when the trigger
signal goes back to high. There will be a period of 'Dead Time' of about 0.85 milliseconds where the motion sensor does not receive a signal. Thus, the return
echo should not return to the Motion Sensor II during this time. When the return echo is detected, the return echo line is forced high.

The CI-6742 Motion sensor II has two different stereo plugs, in which five of six conductors are used. These two plugs connect to a British telecom style
connector at the sensor end. The pins are as follows, with pin 1 numbered from the side of the plug furthest away from the retaining clip:

Yellow plug:

1. Tip: NC (No connection.)


2. Ring: Trigger Signal
3. Sleeve: GND.

Black plug:

1. Tip: + 5 V
2. Ring: Echo Signal
3. Sleeve: GND.

The signal protocol is as follows: Input signal to the sensor is normally +5 VDC. The signal drops to 0 VDC for 0.13 ms. At the falling edge of the input
signal, the output signal from the sensor drops from +5 VDC to 0 VDC. When the echoes have been detected, the output signal rises from 0 VDC to +5
VDC. The trigger rate can be adjusted from 5 Hz to 120 Hz. Receiver gain is a step routine that is built into the Motion Sensor II.

For further assistance, please contact Technical Support at [email protected], through chat on this site during our business hours, or through our web form.
Tech Support can also be reached by phone at 1-800-772-8700.

You might also like