ZXMW Service Configuration Guide

CONTENTS

n Port and VLAN Configuration

l Port Configuration

l LACP Configuration

l VLAN Configuration

n IP and Routing Configuration

n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

2
Port List and Status

ETH Port is Disabled by default

Radio Port is Enabled by default

Radio Port is UP after the radio Link is UP
The Speed is the Radio Link Current Capacity

© ZTE All rights reserved 3

 Configuring ETH Port

Set the port Enabled or Disabled

Electric Port can set to Auto or Force

If set to force ,need to set the Port Rate
Optical Port usually set to Force

© ZTE All rights reserved 4

Configuring ETH Port

Electric Port can set to Auto or Force

If set to force ,need to set the Port Rate
Optical Port usually set to Force

Optical Port can Enable or Disable ALS:

ALS:Automatic Laser Shutdown

© ZTE All rights reserved 5

 Configuring ETH Port

Hybrid Port can set to Optical or Electric

Set the Port Description

© ZTE All rights reserved 6

Configuring Jumbo Frame

Set the Jumbo Frame Value(L2 MTU)

© ZTE All rights reserved 7

Configuring Port-CLI

l interface xgei-1/1/0/1
l description To eNodeB 100-201 Set the Port Description

l mtu 9600 Set the Jumbo Frame Value(L2 MTU)

l no shutdown
l speed speed-1G Shutdown-Enable,No Shutdown-Disable

l exit Set the Speed

© ZTE All rights reserved 8

Checking the Physical Port Basic Status

l NR9150-201(config)#show interface brief

l Interface Portattribute Mode BW(Mbps) Admin Phy Prot Description
l gei-1/1/0/5 electric Duplex/full 1000 up up up
l gei-1/1/0/6 electric Duplex/full 1000 down down down
l gei-1/1/0/7 electric Duplex/full 1000 down down down
l gei-1/1/0/8 electric Duplex/full 1000 down down down
l xgei-1/1/0/1 optical Duplex/full 1000 up down down To eNodeB 100-201
l xgei-1/1/0/2 optical Duplex/full 1000 down down down
l xgei-1/1/0/3 optical Duplex/full 10000 down down down
l xgei-1/1/0/4 optical Duplex/full 10000 down down down
l pla-1/1/0/1 optical Duplex/full 430 up up up
l gei-1/2/0/1 optical Duplex/full 1000 down down down
l xgei-1/2/0/2 optical Duplex/full 1000 down down down
l xxvgei-1/2/0/3 optical Duplex/full 10000 down down down
l xgei-1/4/0/1 optical Duplex/full 10000 down down down
l microwave-1/4/0/1 optical Duplex/full 430 up down down

l microwave-1/4/0/2 optical Duplex/full 430 up down down

© ZTE All rights reserved 9
Checking the Physical Port Detail Status

l NR9150-201(config)#show interface gei-1/1/0/5

l gei-1/1/0/5 is up, ifindex: 8
l Line protocol is up, IPv4 protocol is up, IPv6 protocol is down,
l detected status is RX-OK/TX-OK l IP MTU 1500 bytes

l Last line protocol up time : 2022-01-24 16:11:39 l MTU 1600 bytes

l Holdtime is 10 sec(s) l MPLS MTU 1550 bytes

l The port is electric l SD-FER disable

l The MDIMode of the port is reserved l FER occur threshold is 5e-5

l Loopback none l FER clear threshold is 5e-6

l Duplex full l FER current is 0.0e-9

l Negotiation auto l Fec-eth : disable

l Hardware is Gigabit Ethernet, address is 8413.9fb3.036e l Fec-bypass : N/A

l Internet address is 10.231.226.201/22 l ARP type ARP

l BW 1 Gbit/s

© ZTE All rights reserved 10

Checking the Physical Port Detail Status

l Last Clear Time : 2022-01-24 16:11:24 Last Refresh Time: 2022-01-24 17:02:30
l Rate period : 120 s
l Input : 25192 bit/s 30 packet/s
l Output : 24688 bit/s 5 packet/s
l Peak rate:
l Input : 52312 bit/s peak time 2022-01-24 16:14:20
l Output : 187608 bit/s peak time 2022-01-24 16:14:20
l Intf utilization: input 0% output 0%
l HardwareCounters:
l In_Bytes 7968479 In_Packets 92151 l E_Bytes 16245092 E_Packets 21338

l In_Error 0 In_Broadcasts 66173 l E_Error 0 E_Broadcasts 7

l In_Multicasts 9881 In_CRC_ERROR 0 l E_Multicasts 3190 E_64B 3490

l In_64B 72979 In_65_127B 14848 l E_65_127B 4784 E_128_255B 966
l In_128_255B 1323 In_256_511B 1197 l E_256_511B 990 E_512_1023B 2157
l In_512_1023B 1667 In_1024_1518B 137 l E_1024_1518B 8952 E_Oversize 0
l In_Undersize 0 In_Oversize 0 l E_DropEvents 0
l In_DropEvents 0 l StreamCounters :
© ZTE All rights reserved 11
Checking the Optical Power
l NR9150-201(config)#show opticalinfo xgei-1/1/0/4
l Supply Voltage 1: 3.350 V
l xgei-1/1/0/4
l Supply Voltage 2: N/A
l The optical module is online
l Receiver Sensitivity : N/A
l Transceiver Type : SFP/SFP+
l Receiver Overload : N/A
l Connector Type Code : LC
l Default RX Power PreHighAlarm Thresholds: 0.500 dBm
l Transceiver Mode : smf
l Default RX Power PreLowAlarm Thresholds: -14.401 dBm
l Directionality : Normal
l Default TX Power PreHighAlarm Thresholds: 1.500 dBm
l SONET Compliance Codes : no compliance
l Default TX Power PreLowAlarm Thresholds: -8.199 dBm
l Ethernet Compliance Codes: 10GBase-LR
l Vendor Name: HG GENUINE
l Transfer Distance:9/125(Smf) um fiber 10000 (m)
l Vendor PN : MTRS-02X13-G
l 50/125(Om2) um fiber 0 (m)
l Vendor Rev : 1.0
l 50/125(Om3) um fiber 0 (m)
l Vendor SN : MA20141300154
l 62.5/125(Om1) um fiber 0 (m)
l Authentication : ---
l Copper Line 0 (m)
l AuthenticationCode : ---
l Laser Wavelength: 1310 nm
l ProductSn : ---
l Measured RX Input Power: -40.000 dBm
l ProductDate : ---
l Measured TX Output Power: -40.000 dBm
l Speed : 10000 M
l Measured TX Bias Current: 0.000 mA
l Measured Transceiver Temperature: 30.527 degree(s) Celsius
© ZTE All rights reserved 12
CONTENTS

n Port and VLAN Configuration

l Port Configuration

l LACP Configuration

l VLAN Configuration

n IP and Routing Configuration

n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

13
Configuring LAG

Set the Manual Mode

Select the member

© ZTE All rights reserved 14

Configuring LAG

Set the Load Strategy

© ZTE All rights reserved 15

Configuring LAG

Set the Static Mode Set the SG Priority

Select the member

© ZTE All rights reserved 16

Configuring LAG

Manual Mode

Static Mode

© ZTE All rights reserved 17

Configuring LAG-CLI
l interface smartgroup1
l exit Create smartgroup interface
l interface smartgroup2
l exit

LACP mode
l lacp
l interface smartgroup2
l lacp mode 802.3ad smartgroup2 enable 802.3ad:
Static mode
l exit
l interface gei-1/1/0/6
l smartgroup 2 mode active
l exit smartgroup2 member
l interface gei-1/2/0/1
l smartgroup 2 mode active
l exit
l interface gei-1/1/0/7
l smartgroup 1 mode on
l exit smartgroup1 member
l interface gei-1/1/0/8
l smartgroup 1 mode on
l exit
l exit
© ZTE All rights reserved 18
Checking the LACP Status
l NR9150-201#show lacp counters
l Smartgroup:1
l Actor LACPDUs Marker LACPDUs Marker
l Port Tx Rx Tx Rx Err Err
show LACP Counters
l -------------------------------------------------------------------
l Smartgroup:2
l Actor LACPDUs Marker LACPDUs Marker
l Port Tx Rx Tx Rx Err Err
l -------------------------------------------------------------------
l gei-1/1/0/6 1 0 0 0 0 0
l gei-1/2/0/1 1 0 0 0 0 0

l NR9150-201#show lacp neighbors

l Smartgroup 1 neighbors
l Actor Actor Partner Partner Port Oper Port
l Port Port No. System ID Port No. Priority Key State
l ------------------------------------------------------------------------------- show LACP Neighbors
l Smartgroup 2 neighbors
l Actor Actor Partner Partner Port Oper Port
l Port Port No. System ID Port No. Priority Key State
l -------------------------------------------------------------------------------
l gei-1/1/0/6 9 0xffff,0000.0000.0000 1 255 0x1 0x0
l gei-1/2/0/1 14 0xffff,0000.0000.0000 1 255 0x1 0x0

l NR9150-201#show lacp sys-id show LACP Sys-ID

l Actor System Priority: 32768 Actor System ID: 8413.9fb3.036e
© ZTE All rights reserved 19
Checking the LACP Status
l NR9150-201#show lacp internal
l Smartgroup:1
l Flags: * - Port is Active member Port
l S - Port is requested in Slow LACPDUs
l F - Port is requested in Fast LACPDUs
l A - Port is in Active mode
l P - Port is in Passive mode
l Actor Agg LACPDUs Port Oper Port RX Mux
l Port[Flags] State Interval Pri Key State Machine Machine
l --------------------------------------------------------------------------------
l gei-1/1/0/7 INACTIVE 30 32768 0x0 0x45 N/A N/A show LACP Internal
l gei-1/1/0/8 INACTIVE 30 32768 0x0 0x45 N/A N/A
l Smartgroup:2
l Flags: * - Port is Active member Port
l S - Port is requested in Slow LACPDUs
l F - Port is requested in Fast LACPDUs
l A - Port is in Active mode
l P - Port is in Passive mode
l Actor Agg LACPDUs Port Oper Port RX Mux
l Port[Flags] State Interval Pri Key State Machine Machine
l --------------------------------------------------------------------------------
l gei-1/1/0/6[ A ] INACTIVE 30 32768 0x200 0x45 PORT_DISABLED DETACHED
l gei-1/2/0/1[ A ] INACTIVE 30 32768 0x200 0x45 PORT_DISABLED DETACHED

© ZTE All rights reserved 20

CONTENTS

n Port and VLAN Configuration

l Port Configuration

l LACP Configuration

l VLAN Configuration

n IP and Routing Configuration

n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

21
Configuring VLAN

Add VLAN to the Port

Access Mode only set the PVID

Access Mode

© ZTE All rights reserved 22

Configuring VLAN

Trunk Mode

Set the PVID

Set the VID

© ZTE All rights reserved 23

Configuring VLAN

Configuring VLAN to the PLA Port

Configuring VLAN to the LAG Port

© ZTE All rights reserved 24

Configuring VLAN

After Configuring VLAN to LAG,

the VLAN of the LAG member will be
automatic configured to the same

© ZTE All rights reserved 25

Configuring QinQ

© ZTE All rights reserved 26

 l interface xgei-1/1/0/3
Configuring VLAN-CLI l switchport access vlan 1001
l switchport qinq customer
l exit
l switchvlan-configuration l interface pla-1/1/0/1
l interface gei-1/1/0/7 l switchport mode trunk
l switchport mode trunk l switchport trunk vlan 100-120,1001,4094
l switchport trunk vlan 100-120,4094 l switchport trunk native vlan 4094
l switchport trunk native vlan 4094 l switchport qinq uplink
l exit l exit
l interface gei-1/1/0/8 l interface smartgroup1
l switchport mode trunk l switchport mode trunk
l switchport trunk vlan 100-120,4094 l switchport trunk vlan 100-120,4094
l switchport trunk native vlan 4094 l switchport trunk native vlan 4094
l exit l exit
l interface xgei-1/1/0/1 l vlan 1
l switchport mode trunk l exit
l switchport trunk vlan 100-120,4094 l list 100-120
l switchport trunk native vlan 4094 l vlan 1001
l exit l exit
l interface xgei-1/1/0/2 l vlan 4094
l switchport access vlan 4094 l exit
l exit l exit
© ZTE All rights reserved 27
Checking VLAN List

l VLAN Name PvidPorts UntagPorts TagPorts

l --------------------------------------------------------------------------------
l 1 vlan0001
l 100 vlan0100 smartgroup1
l gei-1/1/0/7-8
l xgei-1/1/0/1
l pla-1/1/0/1 Trunk Mode

l 101 vlan0101 smartgroup1

l gei-1/1/0/7-8
l xgei-1/1/0/1
l pla-1/1/0/1
l 102 vlan0102 smartgroup1
l gei-1/1/0/7-8
l xgei-1/1/0/1
l pla-1/1/0/1
l ...................................................................
© ZTE All rights reserved 28
Checking MAC Table
l NR9150-201(config)#show mac table
l Total MAC address : 1
l Flags: Src--Source filter, Dst--Destination filter
l From:0,driver;1,config;2,VPN;3,802.1X;4,micro;5,DHCP; Check the whole MAC Table
l 6,PBT;7,EVB;8,OTV;9,TRILL;10,ESADI;11,MC-LAG,
l Time--Day:Hour:Min:Sec
l MAC VLAN Outgoing Information Attribute From Time
l -------------- ---- ---------------------------- -------------- ---- -----------
l 8413.9fb3.038e 4094 pla-1/1/0/1 Dynamic 0 00:17:53:11

l NR9150-201(config)#show mac table vlan 4094

l Total MAC address : 1
l Flags: Src--Source filter, Dst--Destination filter
l From:0,driver;1,config;2,VPN;3,802.1X;4,micro;5,DHCP; Check the MAC Table by VLAN
l 6,PBT;7,EVB;8,OTV;9,TRILL;10,ESADI;11,MC-LAG,
l Time--Day:Hour:Min:Sec
l MAC VLAN Outgoing Information Attribute From Time
l -------------- ---- ---------------------------- -------------- ---- -----------
l 8413.9fb3.038e 4094 pla-1/1/0/1 Dynamic 0 00:17:53:26
© ZTE All rights reserved 29
CONTENTS

n Port and VLAN Configuration

n IP and Routing Configuration
n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

30
Configuring VLAN Interface and NMS VLAN

VLAN interface VLAN interface IP VLAN interface Mask

NMS VLAN ID

© ZTE All rights reserved 31

Configuring Static Route

Configuring Static Route

© ZTE All rights reserved 32

IP and Static Route Configuration-CLI

l interface xgei-1/1/0/4 Configuring IP to L3 interface

l ip address 10.1.1.1 255.255.255.0 Only can be configured by CLI
l exit
l interface xgei-1/2/0/2.1000
Configuring IP to L3 Sub interface
l ip address 10.1.2.1 255.255.255.0 Only can be configured by CLI
l exit
l interface vlan4094
l ip address 129.2.10.201 255.255.255.0 Configuring IP to VLAN interface
l exit

l vlan-configuration
l interface xgei-1/2/0/2.1000 Configuring VLAN to L3 Sub interface
l encapsulation-dot1q 1000 Only can be configured by CLI
l exit
l exit

Configuring Static Route

l ip route 172.0.0.0 255.0.0.0 129.2.10.254
© ZTE All rights reserved 33
Checking IP Interface Status
l NR9150-201(config)#show ip interface brief
l Interface IP-Address Mask Admin Phy Prot
l gei-1/1/0/5 10.231.226.201 255.255.252.0 up up up
l gei-1/1/0/6 unassigned unassigned down down down
l gei-1/1/0/7 unassigned unassigned down down down
l gei-1/1/0/8 unassigned unassigned down down down
Check IP interface status,include:
l xgei-1/1/0/1 unassigned unassigned down down down ETH Interface/Radio Interface
l xgei-1/1/0/2 unassigned unassigned down down down /PLA Interface/LAG Interface
l xgei-1/1/0/3 unassigned unassigned down down down /Sub Interface
l xgei-1/1/0/4 10.1.1.1 255.255.255.0 down down down
l pla-1/1/0/1 unassigned unassigned up up up
l gei-1/2/0/1 unassigned unassigned down down down
l xgei-1/2/0/2 unassigned unassigned down down down
l xgei-1/2/0/2.1000 10.1.2.1 255.255.255.0 down down down
l xxvgei-1/2/0/3 unassigned unassigned down down down
l xgei-1/4/0/1 unassigned unassigned down down down
l microwave-1/4/0/1 unassigned unassigned down down down
l microwave-1/4/0/2 unassigned unassigned down down down
l mgmt_eth 192.168.1.1 255.255.0.0 up down down
l vlan4094 129.2.10.201 255.255.255.0 up up up
l smartgroup1 unassigned unassigned up up down
l smartgroup2 unassigned unassigned up up down
© ZTE All rights reserved 34
Checking IP Route

l NR9150-201(config)#show ip forwarding route

l IPv4 Routing Table:
l Headers: Dest: Destination, Gw: Gateway, Pri: Priority;
l Codes : BROADC: Broadcast, USER-I: User-ipaddr, USER-S: User-special,
l MULTIC: Multicast, USER-N: User-network, DHCP-D: DHCP-DFT,
l ASBR-V: ASBR-VPN, STAT-V: Static-VRF, DHCP-S: DHCP-static,
l GW-FWD: PS-BUSI, NAT64: Stateless-NAT64, LDP-A: LDP-area,
l GW-UE: PS-USER, P-VRF: Per-VRF-label, TE: RSVP-TE, NAT-M : NAT-mask
Check IP Route,include:
l BP: BRAS-pool, HAGP: Hybrid-access-gateway-protocol;
Static Route,Direct Route
l Status codes: *valid, >best, R: Relay;
l Dest Gw Interface Owner Pri Metric
l *> 0.0.0.0/0 10.231.224.1 gei-1/1/0/5 Static 1 0
l *> 10.231.224.0/22 10.231.226.201 gei-1/1/0/5 Direct 0 0
l *> 10.231.226.201/32 10.231.226.201 gei-1/1/0/5 Address 0 0
l *> 129.2.10.0/24 129.2.10.201 vlan4094 Direct 0 0
l *> 129.2.10.201/32 129.2.10.201 vlan4094 Address 0 0
l *> 172.0.0.0/8 129.2.10.254 vlan4094 Static 1 0
© ZTE All rights reserved 35
Checking ARP Information Configuring ARP Table

l NR9150-201(config)#show arp
l Arp protect whole is disabled
l The count is 11
l

l IP Address Age Hardware Address Interface Exter VlanID Inter VlanID Sub Interface
l --------------------------------------------------------------------------------
l 10.231.226.201 H 8413.9fb3.036e gei-1/1/0/5 N/A N/A N/A
l 10.231.226.65 00:19:37 ee3d.85bf.5250 gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.231.226.1 00:00:04 744a.a40e.8014 gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.231.226.77 00:00:01 3a04.a126.7140 gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.231.226.61 00:00:01 8adf.e30f.d4d2 gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.231.224.1 00:00:01 d4c1.c820.fe60 gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.231.226.122 00:00:22 8413.9f40.77cc gei-1/1/0/5 N/A N/A gei-1/1/0/5
l 10.1.1.1 H 8413.9fb3.036e xgei-1/1/0/4 N/A N/A N/A
l 10.1.2.1 H 8413.9fb3.036e xgei-1/2/0/2.1000 1000 N/A N/A
l 192.168.1.1 H 8413.9fb3.036e mgmt_eth N/A N/A N/A
l 129.2.10.201 H 8413.9fb3.036e vlan4094 4094 N/A N/A

© ZTE All rights reserved 36

CONTENTS

n Port and VLAN Configuration

n IP and Routing Configuration
n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

37
ERPS Planning

n ERPS Instance 1:
l RPL:201-202 PLA-1/1/0/1-E PLA-1/1/0/1-W
201 202
l RPL Owner:201
l RPL Neighbor:202
microwave-1/4/0/1-W microwave-1/4/0/1-E
l VLAN Group1:1001-1100
l Control VLAN：1001
n ERPS Instance 2:
l RPL:209-210
l RPL Owner:209 microwave-1/1/0/1-E microwave-1/1/0/1-W

l RPL Neighbor:210
209 210
l VLAN Group1:101-120 microwave-1/1/0/2-W microwave-1/1/0/2-E

l Control VLAN：101

© ZTE All rights reserved 38

Configuring ERPS-VLAN-201

Configuring VLAN,include the ERPS VLAN list

Configuring VLAN,include the ERPS VLAN list

© ZTE All rights reserved 39

Configuring ERPS-VLAN Group-201

Enable ERPS

Configuring VLAN Group 1

Configuring VLAN Group 2

© ZTE All rights reserved 40

 Configuring ERPS-ERPS Instance 1-201

Ring ID Set VLAN Group

RPLS Role: RPL Port is the East

RPL Owner

West Port
East Port

Control VLAN

© ZTE All rights reserved 41

 Configuring ERPS-ERPS Instance 2-201

Ring ID
Set VLAN Group

RPLS Role:
Other

East Port West Port

Control VLAN

© ZTE All rights reserved 42

Configuring ERPS-CLI-201

l erps ERPS Mode

l vlan-group 2 protect-vlan 101-120
l vlan-group 1 protect-vlan 1001-1100 VLAN Group
l enable
l ring 1 vlan-group 1 ctrl-vlan 1001 east-port pla-1/1/0/1 west-port microwave-1/4/0/1
l ctrl-vlan 1001
l rpl-role owner east-port
ERPS ring 1
l exit
l ring 2 vlan-group 2 ctrl-vlan 101 east-port pla-1/1/0/1 west-port microwave-1/4/0/1
l ctrl-vlan 101
l rpl-role other
ERPS ring 2
l exit
l exit

© ZTE All rights reserved 43

Configuring ERPS-VLAN-202

Configuring VLAN,include the ERPS VLAN list

Configuring VLAN,include the ERPS VLAN list

© ZTE All rights reserved 44

Configuring ERPS-VLAN Group-202

Enable ERPS

Configuring VLAN Group 1

Configuring VLAN Group 2

© ZTE All rights reserved 45

 Configuring ERPS-ERPS Instance 1-202

Ring ID Set VLAN Group

RPLS Role: RPL Port is the West

RPL Neighbor

West Port
East Port

Control VLAN

© ZTE All rights reserved 46

Configuring ERPS-ERPS Instance 2-202

Ring ID Set VLAN Group

RPL Role:
Other

West Port
East Port

Control VLAN

© ZTE All rights reserved 47

Configuring ERPS-CLI-202

l erps ERPS Mode

l vlan-group 2 protect-vlan 101-120
l vlan-group 1 protect-vlan 1001-1100 VLAN Group
l enable
l ring 1 vlan-group 1 ctrl-vlan 1001 east-port microwave-1/4/0/1 west-port pla-1/1/0/1
l ctrl-vlan 1001
l rpl-role neighbor west-port
ERPS ring 1
l exit
l ring 2 vlan-group 2 ctrl-vlan 101 east-port microwave-1/4/0/1 west-port pla-1/1/0/1
l ctrl-vlan 101
l rpl-role other
ERPS ring 2
l exit
l exit

© ZTE All rights reserved 48

Configuring ERPS-VLAN-209

Configuring VLAN,include the ERPS VLAN list

Configuring VLAN,include the ERPS VLAN list

© ZTE All rights reserved 49

Configuring ERPS-VLAN Group-209

Enable ERPS

Configuring VLAN Group 1

Configuring VLAN Group 2

© ZTE All rights reserved 50

 Configuring ERPS-ERPS Instance 1-209

Ring ID Set VLAN Group

RPLS Role:
Other

West Port
East Port

Control VLAN

© ZTE All rights reserved 51

 Configuring ERPS-ERPS Instance 2-209

Ring ID Set VLAN Group

RPLS Role: RPL Port is the West

RPL Owner

West Port
East Port

Control VLAN

© ZTE All rights reserved 52

Configuring ERPS-CLI-209

l erps ERPS Mode

l vlan-group 2 protect-vlan 101-120
l vlan-group 1 protect-vlan 1001-1100 VLAN Group
l enable
l ring 1 vlan-group 1 ctrl-vlan 1001 east-port microwave-1/1/0/1 west-port microwave-1/1/0/2
l ctrl-vlan 1001
l rpl-role other
ERPS ring 1
l exit
l ring 2 vlan-group 2 ctrl-vlan 101 east-port microwave-1/1/0/1 west-port microwave-1/1/0/2
l ctrl-vlan 101
ERPS ring 2
l rpl-role owner west-port
l exit
l exit

© ZTE All rights reserved 53

Configuring ERPS-VLAN-210

Configuring VLAN,include the ERPS VLAN list

Configuring VLAN,include the ERPS VLAN list

© ZTE All rights reserved 54

Configuring ERPS-VLAN Group-210

Enable ERPS

Configuring VLAN Group 1

Configuring VLAN Group 2

© ZTE All rights reserved 55

Configuring ERPS-ERPS Instance 1-210

Ring ID Set VLAN Group

RPLS Role:
Other

East Port West Port

Control VLAN

© ZTE All rights reserved 56

 Configuring ERPS-ERPS Instance 2-210

Ring ID Set VLAN Group

RPLS Role: RPL Port is the East

RPL Neighbor

West Port
East Port

Control VLAN

© ZTE All rights reserved 57

Configuring ERPS-CLI-210

l erps ERPS Mode

l vlan-group 2 protect-vlan 101-120
l vlan-group 1 protect-vlan 1001-1100 VLAN Group
l enable
l ring 1 vlan-group 1 ctrl-vlan 1001 east-port microwave-1/1/0/2 west-port microwave-1/1/0/1
l ctrl-vlan 1001
l rpl-role other
ERPS ring 1
l exit
l ring 2 vlan-group 2 ctrl-vlan 101 east-port microwave-1/1/0/2 west-port microwave-1/1/0/1
l ctrl-vlan 101
ERPS ring 2
l rpl-role neighbor east-port
l exit
l exit

© ZTE All rights reserved 58

Checking ERPS Status

l NR9150-201#show erps-ring
l ring eastport-status westport-status protocol-status
l -------------------------------------------------------------------------------
l 1 link up,port unblock link down,port block Protection

© ZTE All rights reserved 59

CONTENTS

n Port and VLAN Configuration

n IP and Routing Configuration
n ERPS Configuration
n QoS Configuration
n Synchronization Configuration

60
Configuring DS Domain

Create DS Domain

© ZTE All rights reserved 61

Configuring Common Priority-802.1P IPHB and OPHB

Select DS Domain

Set 802.1P IPHB and

OPHB template

© ZTE All rights reserved 62

 Configuring Common Priority-DSCP IPHB

Set DSCP IPHB

© ZTE All rights reserved 63

Configuring Common Priority-DSCP OPHB

Set DSCP OPHB

© ZTE All rights reserved 64

Configuring Common Priority to the Port

Set DSCP Mapping Select Port

Select DS

Input Mapping

Output Mapping

Set 802.1P Mapping

© ZTE All rights reserved 65

Configuring Class Map

Set CS7 Class Map

Set CS6 Class Map

Set EF Class Map

Set AF4 Class Map

© ZTE All rights reserved 66

Configuring Class Map

Set AF3 Class Map

Set AF2 Class Map

Set AF1 Class Map

Set BE Class Map

© ZTE All rights reserved 67

Configuring Class Map

8 Class

© ZTE All rights reserved 68

 Configuring Policy Map-CS7

Set Policy-Map Name

Select Class

Set Scheduling Policy

© ZTE All rights reserved 69

 Configuring Policy Map-CS6

Set Policy-Map Name Select Class

Set Scheduling Policy

© ZTE All rights reserved 70

 Configuring Policy Map-EF

Set Policy-Map Name Select Class

Set Scheduling Policy

© ZTE All rights reserved 71

 Configuring Policy Map-AF4

Set Policy-Map Name Select Class

Select Weight
Set Scheduling Policy

Set Class CAR

Set WRED

© ZTE All rights reserved 72

 Configuring Policy Map-AF3

Set Policy-Map Name Select Class

Select Weight
Set Scheduling Policy

Set Class CAR

Set WRED

© ZTE All rights reserved 73

 Configuring Policy Map-AF2

Set Policy-Map Name Select Class

Select Weight
Set Scheduling Policy

Set Class CAR

Set WRED

© ZTE All rights reserved 74

 Configuring Policy Map-AF1

Set Policy-Map Name Select Class

Select Weight
Set Scheduling Policy

Set Class CAR

Set WRED

© ZTE All rights reserved 75

 Configuring Policy Map-BE

Set Policy-Map Name Select Class

Select Weight
Set Scheduling Policy

Set Class CAR

Set WRED

© ZTE All rights reserved 76

Configuring Policy Map to the Port

SP+DWRR

Set Policy Map to the Port

© ZTE All rights reserved 77

Configuring DS Domain and Common Priority-CLI

l diffserv domain Common Create DS Domain

l exit
Set DS Domain to the Port
l qos diffserv-domain interface xgei-1/1/0/1 apply Common
l qos priority interface xgei-1/1/0/1 remark ip-dscp
l qos priority interface xgei-1/1/0/1 trust ip-dscp
l qos priority interface pla-1/1/0/1 remark 8021p
l qos priority interface pla-1/1/0/1 trust 8021p

Set Common Priority to the Port

© ZTE All rights reserved 78

Configuring Class Map-CLI
l class-map 7-CS7 match-all l class-map 2-AF2 match-all
l match service-class cs7 l match service-class af2
l exit l exit
l class-map 6-CS6 match-all l class-map 1-AF1 match-all
l match service-class cs6 l match service-class af1
l exit l exit
l class-map 5-EF match-all l class-map 0-BE match-all
l match service-class ef l match service-class be
l exit l exit
l class-map 4-AF4 match-all
l match service-class af4
l exit
l class-map 3-AF3 match-all
Create Class Map
l match service-class af3
l exit

© ZTE All rights reserved 79

Configuring Policy Map-CLI
l class 2-AF2
l bandwidth percent 20
l policy-map Radio
l police cir 50000 cbs 50000 pir 100000 pbs 100000
l class 7-CS7
l random-detect color green percentage 80 95 50
l exit Create Policy Map l random-detect color yellow percentage 50 70 60
l class 6-CS6
l random-detect color red percentage 10 20 90
l exit
l exit
l class 5-EF
l class 1-AF1
l exit
l bandwidth percent 20
l class 4-AF4
l police cir 50000 cbs 50000 pir 100000 pbs 100000
l bandwidth percent 30
l random-detect color green percentage 80 95 50
l police cir 50000 cbs 50000 pir 100000 pbs 100000
l random-detect color yellow percentage 50 70 60
l random-detect color green percentage 80 95 50
l random-detect color red percentage 10 20 90
l random-detect color yellow percentage 50 70 60
l exit
l random-detect color red percentage 10 20 90
l class 0-BE
l exit
l bandwidth percent 5
l class 3-AF3
l police cir 1000 cbs 1000 pir 50000 pbs 50000
l bandwidth percent 25
l random-detect color green percentage 80 95 50
l police cir 50000 cbs 50000 pir 100000 pbs 100000
l random-detect color yellow percentage 50 70 60
l random-detect color green percentage 80 95 50
l random-detect color red percentage 10 20 90
l random-detect color yellow percentage 50 70 60
l exit
l random-detect color red percentage 10 20 90
l exit Set Policy Map to the Port
l exit
l service-policy pla-1/1/0/1 output Radio
l
© ZTE All rights reserved 80
CONTENTS

n Port and VLAN Configuration

n IP and Routing Configuration
n ERPS Configuration
n QoS Configuration
n Synchronization Configuration
l Clock Synchronization Configuration

l Time Synchronization Configuration

81
Global Configuration

Clock Select Policy is SSM Based

Select Standard SSM

Port enable SSM

© ZTE All rights reserved 82

 Configuring Clock Source Configuration-ETH Port

Select Port

Clock type SSM Mode:

Manual

Manually select the Clock Quality

SSM Mode
Automatic

© ZTE All rights reserved 83

Configuring Clock Source Configuration-ETH Port-CLI

l ssm
l usessm
l synchronization-clock line xgei-1/1/0/1
l priority line xgei-1/1/0/1 1 SSM Mode:Manual

l port-receive-mode manual-ssm line xgei-1/1/0/1

l receive-quality line xgei-1/1/0/1 2
l exit

l ssm
l usessm
l synchronization-clock line xgei-1/1/0/1
SSM Mode:Automatic
l priority line xgei-1/1/0/1 1
l receive-quality line xgei-1/1/0/1 2
l exit

© ZTE All rights reserved 84

 Configuring Clock Source Configuration-Radio Port

Select Port

Clock type SSM Mode:

Manual

Manually select the Clock Quality

SSM Mode
Automatic

© ZTE All rights reserved 85

Configuring Clock Source Configuration-Radio Port-CLI

l ssm
l usessm
l synchronization-clock line pla-1/1/0/1
l priority line pla-1/1/0/1 1 SSM Mode:Manual

l port-receive-mode manual-ssm line pla-1/1/0/1

l receive-quality line pla-1/1/0/1 2
l exit

l ssm
l usessm
l synchronization-clock line pla-1/1/0/1
SSM Mode:Automatic
l priority line pla-1/1/0/1 1
l receive-quality line pla-1/1/0/1 2
l exit

© ZTE All rights reserved 86

Checking Master Clock

© ZTE All rights reserved 87

Checking Clock Status

l NR9150-201#show ssmclock clock-config

l SynClock Configuration Information:
l Interface Name :xgei-1/1/0/1
l Clock Type :line clock
Check Clock config
l Priority :1
l Receive SSM Mode :manual
l Quality Level :QL-PRC(0x02)
l Lock Status :clear

l NR9150-201#show ssmclock current-clock

l Current System Clock Information:
l Interface Name :----
l Clock Type :inner clock
Check Current-clock
l PLL Lock Status :free osc
l Use SSM :yes
l Switch Status :auto switch
l Quality Level :QL-DNU(0x0F)
© ZTE All rights reserved 88
CONTENTS

n Port and VLAN Configuration

n IP and Routing Configuration
n ERPS Configuration
n QoS Configuration
n Synchronization Configuration
l Clock Synchronization Configuration

l Time Synchronization Configuration

89
Configuring PTP-TC Mode

TC Mode

Radio Port enable TC

© ZTE All rights reserved 90

Configuring PTP-TC Mode-CLI

l NR9150-201#show running-config ptp

l ptp
l enable
l clock-mode e2etc
l free-mode PTP TC Mode

l exit
l exit

© ZTE All rights reserved 91

Configuring PTP-BC Mode

BC Mode

Set P1 and P2

© ZTE All rights reserved 92

Configuring PTP-BC Mode

Select Port

Set Port State

© ZTE All rights reserved 93

Configuring PTP-BC Mode

Select Port

Set Port State

© ZTE All rights reserved 94

Checking Master Clock

© ZTE All rights reserved 95

Configuring PTP-BC Mode-CLI
l ptp
l enable
l priority1 10
l free-mode
l port interface xgei-1/1/0/1 portnum 2
l enable
l network-protocol ieee802
l manual-port-state slave
l sync-interval -4
Slave Port
l delay-req-interval -4
l vlan 100
l exit
l port interface pla-1/1/0/1 portnum 3
l enable
l network-protocol ieee802
l manual-port-state master Master Port
l sync-interval -4
l delay-req-interval -4
l vlan 100
l exit
l exit
l exit
© ZTE All rights reserved 96
Checking Clock Status-CLI
l NR9150-201#show ptp grandmaster-clock-info
l PTP Grandmaster-Clock Information:
l Clock identity : 84-13-9f-ff-fe-b3-03-6e
l Priority1 : 10
l Priority2 : 128
l ClockClass : 248
l ClockAccuracy : 254
l OffsetScaledLogVariance : 65535 Checking Grandmaster Clock
l Current UTC offset : 37
l Leap61 : FALSE
l Leap59 : FALSE
l Current UTC offset valid: FALSE
l Time scale : PTP
l Time traceable : FALSE
l Frequency traceable : FALSE
l Time source : PTP
l NR9150-201#show ptp master-clock-id
l Master clock id is 84-13-9f-ff-fe-b3-03-6e

© ZTE All rights reserved 97

Checking Clock Status-CLI

l NR9150-201#show ptp status

l PTP Status Information:
l Clock type: bc
l Global state: enable
l PTP version: 2
Checking PTP status
l Domain value: 0
l State algorithm: manual
l Clock id: 84-13-9f-ff-fe-b3-03-6e
l Device accuracy: high

l NR9150-201#show ptp steps-from-grandmaster Checking PTP steps-from-grandmaster

l Steps removed from grandmaster is 0

© ZTE All rights reserved 98

Thank you!