COPYRIGHTED-CUSTOMER INFORMATION DRAWING 1 COPYRIGHTED-CUSTOMER INFORMATION DRAWING COPYRIGHTED-CUSTOMER INFORMATION DRAWING 2 COPYRIGHTED-CUSTOMER INFORMATION DRAWING

QTY ITEM NO. DESCRIPTION PART NO.

26
1 1 BASE,MOTOR,WELD & MACH S022437

COPYRIGHTED-CUSTOMER INFORMATION DRAWING

COPYRIGHTED-CUSTOMER INFORMATION DRAWING
ALIGN SLOT IN RETAINER 1 2 GUARD,GEAR,WELD & ASSEMBLE S022441
WITH LUBE HOLE. 2 PLCS 2 3 BRG,BALL MP093886
16 15 14
1 4 GEAR,SPUR MP252067
2 4 1 5 DRUM,TRIP CABLE MP265850
1 6 SHAFT,DIPPER TRIP MTR MP426367
1 1 7 GUARD,DRUM,DIPPER TRIP,WELDED MP252070
20
20 L 2 8 MOTOR,ELECTRIC,120V DC MP333033
9 L
1 9 RETAINER,MACH MP252068
5
21.64
1 10 RETAINER,MACH MP252069
APPROX 5
C.G. 2 11 PINION,SPUR,2.833PDx17T MP021898
8 12 SCR,HEX,.5x4,UNC,GR 8 03286281
6 PLCS AT 17 18
8 8 13 WASHER,CONICAL,12MM MP600697
ITEMS 9 & 10
18 14 WASHER,FLAT,.5,HARDENED 03951650
2 15 WASHER,LOCK,.5,HVY 03961500
6 43.41 2 16 SCR,HEX,.5x.75,UNC,GR 5 03285240
3 3
REF 12 17 WASHER,LOCK,.375,HVY 03961300
12 18 SCR,HEX,.375x1,UNC,GR5 03279320
25
8 19 NUT,HEX,FULL,.5,UNC 02711050
2 20 FTG,LUBE,HYD,.125,STR 57043760
COPYRIGHTED-CUSTOMER INFORMATION DRAWING

COPYRIGHTED-CUSTOMER INFORMATION DRAWING

8
7 16 21 SHIM,STEEL MP326932
10 8 22 SHIM,LAM,.125x2x2 MP326933
7 8 23 SHIM,STEEL MP326934
2 24 KEY,GIB MP397866
1 1 25 KEY,GIB S094430
SEE NOTE 2 3
1 26 NAMEPLATE,INSPECTION MP037716
2

SECTION A-A
14.69
APPROX

A 40.50
REF 15°
2
3

2 PLCS 24
B .75

8 PLCS
C
3 3
13 19 7

12.445 12.445 8
C.D. C.D.

28.25
8 PLCS
C 180 OPENING
8 REF

4 21 22 23
4
SEE NOTE 1
12.19
1
.12

11
B
A 1.25 2 PLCS
VIEW B-B
COPYRIGHTED-CUSTOMER INFORMATION DRAWING

1 REF

COPYRIGHTED-CUSTOMER INFORMATION DRAWING

11.289 12
REF
14
REVISION DATA REISSUE DATE 08-26-2010
14
SOLIDWORKS

20102018445
TIGHTEN TO 105 FT-LBS DRAWING

PICTORIALLY UPDATED DIPPER TRIP MOTORS (P/N

MP333033), 12.445 DIM WAS 12.417, 40.50 DIM
8 PLACES
THIS DOCUMENT IS PROTECTED UNDER APPLICABLE COPYRIGHT LAWS TO THE EXTENT AVAILABLE.
ANY UNAUTHORIZED AND UNLAWFUL REPRODUCTION, DISTRIBUTION OR OTHER USE SHALL BE
SUBJECT TO LIABILITY. C 2003 Bucyrus International, Inc. ALL RIGHTS RESERVED.
NOTES: 7 ALL DIMENSIONS IN INCHES-UNLESS OTHERWISE SPECIFIED

Guzzo A. DATE 08-26-2010 ECN

MACHINING TOLERANCES-UNLESS OTHERWISE SPECIFIED
.12 1. 2 PLACE DECIMAL DIMENSIONS .01 FOR EACH 12 MAX ± .09
1. START WITH ITEM 23 & ADD SHIMS 22 & 21 AS 1 2. 3 PLACE DECIMAL DIMENSIONS .005 UP TO 36, .010 OVER 36

REQUIRED TO OBTAIN 80% MIN FACE CONTACT

3.
4.
CONCENTRICITY OF CYLINDRICAL SURFACES = .010 T.I.R.
PARALLELISM, SQUARENESS, OR ANGULARITY BETWEEN SURFACES Bucyrus
AND/OR HOLE CENTERLINES 0 7' (.002 INCH/INCH) International, Inc.
& MAINTAIN .005" - .015" BACKLASH.
R

FABRICATING TOLERANCES-UNLESS OTHERWISE SPECIFIED

1. MATERIAL THICKNESS DIMENSIONS TOLERANCE
A. LESS THAN .12 0 TO 36 .03

2. INSTALL BEARINGS WITH GREASE SEAL NEXT TO

OVER 36 .06
B. .12 TO .50 0 TO 36 .06
OVER 36 .12
GEAR. PACK BEARINGS WITH GREASE AT ASSY. C. .50 TO 1.00 0 TO 36 .09 DESCRIPTION

D. OVER 1.00
OVER 36
0 TO 36
.19
.19 DIPPER TRIP,SHOP ASSEMBLY
OVER 36 .25
REF DWGS
S022457

SECTION C-C
2. BENT ANGLES 1 (.017 IN/IN) FOR EACH .37 OF MATERIAL
THICKNESS (MAX 3 )
MODEL UNIT FIN WGT
WELDMENT TOLERANCES-UNLESS OTHERWISE SPECIFIED 495 5400 1848.0
DET

BY
1. DIMENSION MATERIAL THICKNESS TOLERANCE DATE REV

WAS 40.79
ITALIANO M. 02-19-2004

DESCRIPTION
A. UP TO 36"

B. 36" TO 10'
UP TO 1"
1" AND GREATER
UP TO 1"
.06
.12
.12
ENG
CONTACT HAWS M. DWG
SIZE D 3

3
S022456
1" AND GREATER .19 NO. SHEET

1 OF 1
C. 10' TO 30' UP TO 1" .19

REV
1" AND GREATER .25
D. OVER 30' ALL .25

COPYRIGHTED-CUSTOMER INFORMATION DRAWING 1 COPYRIGHTED-CUSTOMER INFORMATION DRAWING COPYRIGHTED-CUSTOMER INFORMATION DRAWING 2 COPYRIGHTED-CUSTOMER INFORMATION DRAWING