Construction of Hanger at AMRELI

ABSTRACT SHEET (ELECTRICAL )

SR. NO. SOR NO DESCRIPTION QUANTITY PER UNIT

H.T. WORK
1 10-4-6. Supply of 315 KVA Outdoor type Compact Substation 1 Each
consisting of Transformer,HT switchgear and LT
Switchgear and confirming to IEC-62227. a) Transformer:
315 KVA Copper wound 11KV /433 V DYn11, Dry Cast
resin type Transformer with tapping range +10 to -10% @
2.5% ( with tolerance), class F , with surge restorers,
Digital WTI, IS1171 as per b) HT Compartment: 11KV,
21kA for 3 Sec . 630 A 50 Hz, gas insulated VCB in SS
tank in sheet enclosure having provision for one no. direct
connection of Incoming supply cable upto 300sq mm and
one no. VCB( Manually charging & closing) in series with
LBS between VCB and Transformer, Self Powered Relay 3
O/C +1 E/F Relay type CSPR-V5, mechanical ON/OFF
indicator, trip coil , Manual Close & Trip PB, live cable
indicator, mechanical interlocks, pad locking facility, SF6
gas manometer, cable boots, 3 nos. CTs with Ratio -/1A,
Cl: 5P10, 2.5 VA for protection c) LV side compartment :
one no. MCCB of 500A, 36kA, 4Pole, Microprocessor
based release with arrangement for bottom cable
termination

( 100% for phase & 50% for N, Current density - 1A/ sq

mm) The enclosure should be of IK10 type.The Enclosure
shall construction shall be GI of thickness at least
1.6/2mm.The enclosure shall be Powder Coated. Each
compartment will be provided with the door and pad
locking arrangement. The Compartment illumination lamp
with door operated switch shall be provided for each
compartment. The Transformer compartment will have IP-
34 ingress protection, whereas the HT/LT compartment will
have IP-54 protection.The connection between HT and
Transformer shall be by 3 runs of single core 95 sq mm
XLPE aluminium cable and between Transformer to LT
switchgear shall be by appropriate Aluminium PVC
sleeved Busbar MAKE: ABB,SIEMENS,SCHNEIDER

Package Sub-Station will be complete with the internal

interconnections & earthing, Outdoor type enclosure
having modular construction of Galvanised Sheet Steel
having thickness 2mm for Load Bearing Member and
1.5mm for Non Load Bearing Member with 4mm HRCA
baseframe, CSS shall be as per IEC 62271-202, routine
tests as per relevant IEC shall be carried out during
inspection on the entire CSS.The CSS Should be supplied
by OEM or System channel partner.
 CSS Shall be Tested at factory as per Approved
QAP and applicable IS/IEC standard.

Final CSS assembling & inspection to be done

at OEM factory only.
2 R.A. Supply,installation,testing and commissioning of outdoor 1 Each
11KV, 800A HT Metering cubicle panel ( HTMC )with
VCB/LBS as per Technical specifications No:
UGVCL/R&D -PP/TS/HTMC/001/R1 for outdoor
installation.( CTPT & Meter excluded ). Make:SAP
Enterprise,Goodluck,National power, Expert Engineers.

3 10-4-2. Supplying and erecting, commissioning and testing of

Diesel Generating set confirming to IS: 4722:1968 &
BS:5514 having continuous rating, 3 phase, 415 volts, 50
cycles A.C. supply comprising of a totally enclosed
air/water cooled diesel engine with multi-cylinders
developing suitable BHP not less than following capacity
at 1500 RPM with 10% overload for one hour in 24 hours
with standard accessories like fly wheel, lubricating oil
cooler, "A" class governor, heavy duty fuel wheel and
lubricating oil filter, oil bath air filler, lubricating oil pressure
gauge, end exhaust manifold, standard set of tools with
adjustable spanners, screw drivers, cylinder head to cover,
joint cylinder head to exhaust, element lube oil filter, 12 /
24 volts electric starting equipment complete with standard
heavy duty battery, dynamo, cut-outs, ammeter, necessary
wiring, pressure gauge, starter etc and heavy duty
Residential type exhaust silencer and vertical hot air duct
both

logged with asbestos rope, save oil trays, exhaust piping of

required length, standard wall/floor mounted fuel with level
indicator and piping and drip proof alternator, self excited,
self regulated, screen protected, with excitation system,
capable of delivering the rated system output at 415 volts,
3 phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM,
conforming to IS-4722- 1968 with voltage regulation +/-
5% of rated voltage from no load to full load. Both the
engine and alternator fitted on a common fabricated steel
base plate with antivibration mounting engine and
alternator both connected to each other by flexible flange
coupling and with floor/wall mounted control panel box
comprising of voltmeter ammeter, selector switches,
ACB / MCCB / MCB of adequate capacity,
 indicator lamps duly wired with HRC fuses. The alternator
& control panel shall be connected with provided suitable
capacity armoured cable and complete with Acoustic
enclosure (canopy) made out of 16 SWG CRCA Sheet,
sound absorbing material Rockwool of 64 density & 100
mm thick conforming to IS:8183 / PU Foam of 40 Density -
at least 40 mm. The resin bonded rockwool covered from
inside the canopy by perforated sheet with 3/4 mm holes,
sound level not more than 75 dB at a distance of 1 mtr, as
per PVCT norms. Erection, commissioning and satisfactory
testing as per requirement with first filling of fuel, oil, etc.
with guarantee / Warrantee of complete system for Two
years. & with obtaining all necessary certificate from
Electrical Inspector. The Capacity and Ratings of DG sets
are as below.

10-4-2 ( S ) (S) Continuous rating of 320 KVA ,BHP not less than 375 1 Each
BHP
4 10-4-3. Providing & erecting approved make ATS panel suitable
for following size of 3 phase, 415 V., 50 cycles, A.C.
diesel generating set complete of scope as detailed below:
1) Power module: Motorised Changeover switch with ATS
controller, Auxiliary contactor with NO & NC contacts with
Automatic Battery Charger, indicating lamps for Generator
ON, Mains ON, Load and suitable control terminals and
power terminals with neutral earthing studs.

10-4-3 ( H ) (H) ATS Panel for 320 KVA/ 380 / 400 /500 KVA3 ph DG 1 Each
Set
5 10-2-14. Providing and erecting ISI Marked 3core 120 Sq.mm XLPE 25 Mtr
insulated 11 KV armoured cable Aluminium conductor IS-
7098 to be laid on wall with clamps or in provided cable
trench / pipe approved manner as directed.

6 10-2-19. Providing and erecting cable end termination kit, heat

shrinkable Push on type Densons/ Raychem/ Elastimold
make suitable for 11 KV XLPE cable 3core 95 & 120
Sq.mm
6a 10-2-19 ( A ) (A) Outdoor type 1 E.a.
6b 10-2-19 ( B ) (B) Indoor type 3 E.a.
7 4-3-3. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe of following size of cables

4-3-3( G) (G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core) 60 Mtr
8 4-6-3. Providing and, fixing heavy duty flange type brass double
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables.

4-6-3(F) (F) 3 & 1/2 core 150 Sq. mm 10 E.a.

9 4-7-1. Solder less crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.
9a 4-7-1 ( H ) (H) 150 Sq.mm. 30 E.a.
9b 4-7-1 ( E ) (E) 70 Sq.mm. 10 E.a.
10 10-2-25. Supplying & erecting D.C.P. type fire extinguisher for
following capacity cartridge type with gun metal cap 150
gram CO2 gas cartridge, powder and brackets confirming
to IS 2171 1985 and complete erected with necessary
clamps made from 50 x 6 mm M S Flat with nuts and bolts
grouted in wall complete.

10-2-25 ( B ) [B] For 10 KG Capacity 2 E.a.

11 10-2-26. Supplying & erecting carbon dioxide (CO2) fire
extinguisher user of following capacity with necessary
clamps made from 50 x 6 mm M.S. Flat with nut & bolts
grouted in wall complete.
10-2-26 ( A ) [A] For 4.5 Kg Capacity 2 E.a.
12 10-2-1. Providing and fixing printed instruction chart both in 2 E.a.
English and Gujarati and duly framed with front glasses,
for treatment of person suffering from Electric shock with
minimum 50" diagonally size.
13 10-2-2. Providing pair of rubber hand gloves suitable for working 2 E.a.
on 11 KV/22 KV supply.
14 10-2.-3. Supplying rubber matting of following thickness as per
IS:15652/IEC 61111
10-2-3 ( c ) (c)12mm 2 Sqmtr
15 10-2-4. Supplying stand first AID box with antiseptic cream, 2 E.a.
medicine for use on wounds due burn, crepe bandage,
gauge bandage, medicated ready to use bandage (Band-
aid) adhesive tape for medicinal user, Scissors, anti-septic
solution (Savlon or similar) etc. (All above contents shall
be of standard makes)

16 10-2-5. Supplying FIRE bucket round bottom of 9 litres capacity 3 E.a.

made out of 24 gauge G.I. sheet with extra handle at
bottom duly painted white inside and Red out side with
FIRE mark, filled with dry-sand and kept on existing stand
provided or hung on wall hook.

17 10-2-5. Supplying and erecting floor mounting stand for keeping 1 E.a.
four nos. of FIRE buckets comprising 1500 mm in length,
900 mm height frame made out of 30mm X30 mm X 4 mm
angle iron with cross supports for legs, welded with 4
hooks and duly painted with one coat of red lead and two
coats of approved enamelled silver paint.

18 3-14-1. Providing and erecting required size Aluminium strip for 80 Kg

earthing of H.T. , OCB / ACB / Transformer, LT panel
board, Motors etc. using copper clamp.
19 3-14-2. Providing and erecting required size HOT deep Galvanised 60 Kg
iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT
panel board, Motors etc. using proper clamp.

20 3-14-3. Providing and erecting required size Copper strip for 180 Kg
earthing of H.T. OCB / ACB/ Transformer, LT panel board,
Motors etc. using copper clamp.
21 3-14-9. Supplying & erecting earth pit of minimum bore dia.150mm
size approved make Earthing Electrode consisting Pipe-in-
Pipe Technology as per IS 3043-1987 made of corrosion
free hot dipped G.I.Pipes having Outer pipe dia of 50mm
having 80-200 Micron galvanising, Inner pipe dia of 25 mm
having 200-250 Micron galvanising, connection terminal
dia of 12mm with constant ohmic value surrounded by
highly conductive compound with high charge dissipation
suitable for following type of applications with chamber and
heavy duty cover.(approved make OEM has to submit test
certificate) & having back filling compound of (B) Inner
chemical (CCM Compound)- Resistivity:- 0.2 / meter
testing as per IEC 62561-2017, Voltage drop:- < 1 volt at
no load & dry form, Sulphar content:- <2%(C) Back fill
Compound :- Earthing compound should be capable to
retain moisture for long time Necessary test report must
be submitted.

3-14-9 ( C ) (c) For Electrical Installation covering Transformer 8 E.a.

Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive
Computer System(like Automation, SCADA) i.e
independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.

22 3-14-10. Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-1987
made of corrosion free hot dipped G.I.Pipes having Outer
pipe dia of 80 mm having 80-200 Micron galvanising,
Inner pipe dia of 40 mm having 200-250 Micron
galvanising, connection terminal dia of 14 mm with
constant ohmic value surrounded by highly conductive
compound with high charge dissipation suitable for
following type of applications with chamber and heavy
duty cover.(approved make OEM has to submit test
certificate including value of earth resistane of installation.

3-14-10 ( C ) [C] For Electrical Installation covering Transformer 4 E.a.

Neutrals, Lightning arrester Earthing, A.C.Plant &
Sensitive Computer System(like Automation,
SCADA)i.e. independent Earthing located in other than
normal soil i.e. Soft Rock, Marshy Soil etc..
-Length of Pipe : 3 Mtrs.
-Back filling Compound :2 nos Bags of 25 Kg.

23 3-16-4 A Providing , erecting , fabricating the M.S. structure as per 450 Kg

requirement on site incorporating proper size of M.S.
angles,square,round, flats, bars, channels, sections
complete with cutting, welding, grinding & finishing duly
painted with one coat of red oxide with erection on site as
per direction of engineer in charge with necessary
grouting, cementing, plastering & finishing complete.

24 3-16-4 B Providing and erecting ,Fabricating the box type items 80 Kg

made from M.S. Sheet with A.I. supports, wings, doors,
handles other hardware materials as per requirement
design with finishing by three tank powder coating
processed inside and outside painted, erected as directed
including minor civil work.
25 4-5-7. Providing & laying. R.C.C. Hume pipe for cable to be laid
90 cm. below ground across the road crossing or on floor
with necessary material in an approved manner and
making the ground as per original.
25a 4-5-7 ( C ) (C) 300 mm dia 10 Mtr
25b 4-5-7 ( E ) (E)150 mm dia 10 Mtr
GENERAL ELECTRICAL WORK
26 1-2-1. Point wiring for Light / Bell with 2-1.5 sq.mm & earth
wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multi strand copper wires up to
10 mtr length , in below type of pipe erected with 6A
Modular type switch / bell push & accessories and earth
continuity of following type, erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured/metallic/white front plate modules
erected on / in wall / ceiling as per pipe erected, with
necessary Lamp holder/ceiling rose / H.D.Connector as
directed.

(a) with medium class Rigid PVC pipe and accessories 265 Pt.
erected flushed on wall/ceiling complete

27 1-2-2. Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5
sq.mm (Green) both are of .ISI marked 1.1 KV Grade
FRLS PVC insulated multi strand copper wires up to 10
mtr length, in below type of pipe erected with 6A Modular
type switch and hum free EME step type electronic fan
regulator mounted and accessories with earth continuity
of following type erected on PVC / Metallic/Wooden box,
single mounting base frame covered with
textured/metallic/white front plate modules erected on / in
wall / ceiling as per pipe erected. with necessary ceiling
rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories 125 Pt
erected flushed on wall/ceiling complete

28 1-2-3. Point wiring for Individual Plug with & earth wire of 1.5
sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS
PVC insulated multi strand copper wires up to 10 mtr
length, in below type of pipe erected complete with
Modular type switch & 5 pin Plug erected on PVC /
Metallic/Wooden box covered with appropriate front plate
modules erected on / in wall / ceiling as per pipe erected
with following type of accessories.

1-2-3 ( I ) [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire
from nearby switchboard/mcb db board
28a (a) with medium class Rigid PVC pipe and accessories 265 Pt
erected flushed on wall/ceiling complete

1-2-3 ( II ) [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.
Wire from mcb db board.
28b (a) with medium class Rigid PVC pipe and accessories 5 Pt
erected flushed on wall/ceiling complete

1-2-3 ( III ) [III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu.
Wire with 2.5 sq.mm ( green) earthing wire from mcb d b
board.
28c (a) with medium class Rigid PVC pipe and accessories 2 Pt
erected flushed on wall/ceiling complete

29 1-2-4. Point wiring for on board Looped Plug with 6A Modular 170 Pt
type switch & 5 pin socket erected on PVC /
Metallic/Wooden box, single mounting base frame covered
with textured / metallic/white front plate modules erected
on / in wall / ceiling with following type accessories

30 1-2-6. Point wiring for secondary light point with 2-1.5 sq.mm &
earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1
KV grade FRLS PVC insulated multi strand copper wires,
in below type of pipe to be erected complete with earth
continuity and necessary connection with primary light with
accessories erected on Metal / PVC / wooden box
covered covered with appropriate front plate modules
erected on / in wall / ceiling for open / concealed wiring.
with necessary Lamp holder / ceiling rose / H.D.Connector
as directed.as per pipe erected with following type of
accessories.

Note:- Maximum up to 6 mtrs length, excess will be

considered as Mains for Secondary Point.
1-2-6 ( a ) (a) with medium class Rigid PVC pipe and accessories 270 Pt
erected flushed on wall/ceiling complete

31 1-2-7. Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting
base frame covered with textured / metallic/white front
plate , modules erected with necessary connections as
per site situation directed by Engineer In charge.

31a 1-2-7(1). (1)One No. SP 6 Amp. 10 E.a.

31b 1-2-7(2) (2) One No 5 pin plug 10 E.a.
31c 1-2-7(3) (3) Two Pin/RJ-11 Telephone Socket
31d 1-2-7(3A) [A] For One Gang 56 E.a.
31e 1-2-7(3B) [B] For Two Gang 2 E.a.
31f 1-2-7(4) (4) TV Co-axial Socket outlet 2 E.a.
31g 1-2-7(7) (7) Blank Plate Single 40 E.a.
31h 1-2-7(9) (9) 16 Amp. SP one way switch 5 E.a.
31i 1-2-7(10) (10) 6/16Amp. Universal socket 45 E.a.
31j 1-2-7(13) (13) 6A/10A/16A/20A/25A/32A Single pole Modular MCB 5 E.a.
Switch
31k 1-2-7(14) (14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular 45 E.a.
MCB Switch
31l 1-2-7(20) (20) Modular Buzzer 4 E.a.
31m 1-2-7(21) (21) Foot Light as per colour requirement with concealed
box, modular accessories, acrylic glass cover with suitable
LED watt with all accessories as per following module

(b) Four modules 12 E.a.

31n 1-2-7(23) (23) USB Charger with output of 5 V DC,2.1 A with inbuilt 10 E.a.
surge protection.
Cat-III
32 1-3-2. Providing and erecting ISI mark Medium class RIGID PVC
PIPES of following size complete to be erected on/in wall
or ceiling erected with necessary PVC fittings & Junction
boxes fixed with adhesive solution & Clamps with following
dia of pipes, in approved manner as directed

32a 1-3-2(a) (a)20 mm 220 Mtr

32b 1-3-2(b) (b) 25 mm 1350 Mtr
32c 1-3-2( c ) (c) 32 mm 50 Mtr
33 1-3-4. Providing & erecting PVC Corrugated Flexible Conduit with
required nos. of coupling, PVC bushes, Check-nuts etc.
complete of following sizes.

33a 1-3-4(2) (2) 25 mm 60 Mtr

33b 1-3-4(3) (3) 32 mm 150 Mtr
33c 1-3-4(4) (4) 40 mm 40 Mtr
33d 1-3-4(5) (5) 50 mm 60 Mtr
34 1-3-5. Supplying & erecting UPVC Mini trunking (PVC Casing-n-
Capping) having double-locking arrangement with grooves,
trunking of size not below 12.5 mm in height as per IS with
accessories of PVC/Resin polypropylene not below 1.8
mm thick duly sealed in joint & erected on wall / ceiling of
following size .

34a 1-3-5(2) (2) 25 mm 80 Mtr

34b 1-3-5(3) (3) 32 mm 80 Mtr
35 1-3-6. Supplying and laying UPVC cable trunking system
comprising unplasticised polyvinyl, chloride rigid material
with ignition free and flame proof confirming BS with
necessary end caps Internal and external bend, flat bends,
coupler, tee etc..All necessary accessories and measuring
of following sizes

35a 1-3-6(2) (2) 100 mm x 50 mm trunking 120 Mtr

35b 1-3-6(4) (4)100 mm x 50 mm trunking with TWIN compartment 30 Mtr
With clip in divider
36 1-3-7. Supply & installation of surface mounted U PVC snap-on
adaptable trunking raceways, fabricated out of U-PVC to
Off-White or approved shade as per IS 733 of thickness
2.0mm for the base and sides with all accessories like
removable covers, joints ,height spacer,angles complete
with necessary bends, suitable sized junction boxes and
tees etc, Complete.

(b)Size: 50x130 mm PVC Raceways for Power & Data with 15 Mtr
2 compartments above specifications.
37 1-3-8. Providing & Erecting eight module pop up floor box/flushed 2 E.a.
with table surface Conform to IEC 60670-1, IEC 60670-23
& IEC 60884-1 with required items as demanded by
engineer in charge with complete finishing .cat-III

38 1-3-9. Supply & installation of modular type accessories for U

PVC snap-on adaptable trunking/Pop up Box with required
items erected with necessary connection. As desired by
Engineer In charge
38a 1-3-9(i) i) 6 A SP 1 Way Switch cat-III 10 E.a.
38b 1-3-9(ii) ii) 16A SP 1 Way Switch cat-III 2 E.a.
38c 1-3-9(iv) iv) 6/16 A universal socket shuttered cat-III 2 E.a.
38d 1-3-9(v) v) RJ-11 Telephone socket cat-III 2 E.a.
38e 1-3-9(vi) vi) Cat-6 LAN Socket cat-III 4 E.a.
39 1-4-1. Providing and erecting Mains with 1.1 KV grade FRLS
PVC insulated ISI marked stranded Copper conductor wire
in following type of pipe to be erected concealed in
/flushed on wall/ceiling, with 1.5 sq. mm copper conductor
FRLS PVC insulated stranded wire of green colour for
earth continuity of following size

39a 1-4-1(A) (A) With medium class Rigid PVC pipe and accessories

39b 1-4-1(a) (a) 2 wire 1.5 sq. mm 1980 Mtr

39c 1-4-1(b) (b) 2 wire 2.5 sq. mm 3700 Mtr
40 1-4-2. providing and erecting Mains with 1.1 KV grade FRLS PVC
insulated ISI marked stranded Copper conductor wire in
following type of pipe to be erected in / on wall / ceiling
with 2.5 sq. mm copper conductor FRLS PVC insulated
stranded wire of green colour for earth continuity of
following size

40a 1-4-2(A) (A) with medium class Rigid PVC pipe and accessories

40b 1-4-2(a) (a) 2 wire 4 sq. mm 50 Mtr

40c 1-4-2(b) (b) 2 wire 6 sq. mm 60 Mtr
40d (c) 2 wire 10 sq. mm 5 Mtr
(use earth wire of 4 sq.mm )
41 1-4-4. providing and erecting Mains with ISI marked, 1.5KV grade
electrolyte multi stranded, annealed copper conductor with
heat resistant PVC insulated conforms to IS 694, IEC - 227
erected in existing pipe of following size (Specifically for
control panel, relays, power switchgears, motor starters &
control wiring) with required size of copper lugs, nuts and
bolts if required.

41a 1-4-4 ( e ) (e) One wire 6.00 sq. mm 50 Mtr

41b 1-4-4 ( f ) (f) One wire 10.00 sq. mm 50 Mtr
41c 1-4-4 ( g ) (g) One wire 16.00 sq. mm 40 Mtr
41d 1-4-4 ( h ) (h) One wire 25.00 sq. mm 80 Mtr
41e 1-4-4 ( i ) (i) One wire 35.00 sq. mm 10 Mtr
42 1-4-5. Supplying and erecting Flexible PVC insulated multi strand
multi core 1.1 kv grade ISI marked copper wires of
following size to be erected as directed.
42a 1-4-5( e) (e) 1.50 Sq.mm 3 core round PVC sheathed 510 Mtr
42b 1-4-5( f) (f) 1.50 Sq.mm 4 core round PVC sheathed 350 Mtr
42c 1-4-5( h) (h) 2.50 Sq.mm 3 core round PVC sheathed 110 Mtr
42c 1-4-5( i) (i) 2.50 Sq.mm 4 core round PVC sheathed 1260 Mtr
43 1-4-6. Providing & Erecting approved make following size of TV
Co-axial flexible cable comprising inner conductor of solid
bare copper insulated with Foam PE & Secondary
conductor made of poly - Aluminium film bonded Al. Braids
@ suitable coverage overall sheathed with black PVC
insulation.

(e) RG-11 50 Mtr

44 7-1-2. SITC of Digital / PCM / TDM EPABX System having SMT
design, system with flexible universal slots. Inbuilt Auto
attendant facility, Minimum 15 Nos. conference, Analog
extension line, Calling GSM, E&M line, PRI / EI & VOIP
program me through Analog telephone digital key from
Ethernet, public address cord, shall have unrestricted
simultaneous dialing facility, QSIG protocol on PRI, 95 /
STD / ISD / Local-Locking, Class of Service, Quick Dial-
Single Digit dialing of any two external number, Once only
ring device, Boss/Secretary-Do not disturb Facility, Power
Down Mode, Hot Line, Hot Outward Dialing, Day Night
Mode, Auto Call Back, Barge-in, Call Pick Up & Call
Transfer, Call transfer while Ringing with Voice Guide
System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base
routing Internet Ready Port, External Music Port, Call
Budgeting, Call Most Calculation (ASMDR), DID Direct
Inverse Dialing, External Music Input, Fax Homing, Global
Directory Printing with following capacities

7-1-2( D ) [D] No of Extension 64, No of Junctions 12, 8 Port IP 1 E.a.

Resource in-built, 4 Port Web base Video Conferencing,
No of expandable ports : 240, Operators Console - 01
Compatible : ISDN and Networking

45 7-1-8. Supplying & erecting push button type telephone 60 E.a.

instrument having speaker phone Caller ID & hands free
dialing system & 30 memories with display system
(a) Single line BEETEL/panasonic or equivalent make

46 1-4-7. Supplying & erecting approved make Telephone Cable

electrolytic copper conductor PE insulation twisted in two
pairs, & wrapped with FRLS PVC tape & sheathed with
FRLS PVC or HFFR outer Jacket suitable for telephone
wiring & confirming to C-DOT erected in existing pipe. of
following size of conductors & nos.of pairs. With necessary
connections.

[A] Conductor Size 0.5 mm

(a) Unarmoured
46a 1-4-7(2) (2) Two Pairs 2150 Mtr
46b 1-4-7(4) (4) Five Pairs 250 Mtr
46c 1-4-7( 6 ) (6) Twenty Pairs 150 Mtr
(b) Armoured [Jelly Filled]
46d 1-4-7(b-1) (1) Ten Pairs 80 Mtr
46e 1-4-7(b-2) (2) Twenty Pairs 40 Mtr
46f 1-4-7(b-3) (3) Fifty Pairs 40 Mtr
47 1-4-8. Supplying & erecting approved make LAN cable of
following size in existing pipe as per direction
1-4-8( C ) [C] CAT - 6 150 Mtr
48 1-4-9. Providing & erecting main Distribution (MDF) indoor type,
back mounted frame as per DoT standard approved with
krone strips
48a 1-4-9(a) (a) Suitable for 10 pair 1 E.a.
48b 1-4-9(b) (b) Suitable for 20 pair 1 E.a.
48c 1-4-9( c ) (c) Suitable for 50 pair 2 E.a.
48d 1-4-9( d ) (d) Suitable for 100 pair 1 E.a.
49 1-5-1. Supplying & erecting M.S. Box having 16 Gauge painted
with red oxide or Heavy duty PVC box erected flushed on
wall or concealed in wall with necessary plastering &
finishing as directed of following size.

49a 1-5-1(a) (a) 100 mm x 100 mm x 75 mm(d) 20 E.a.

49b 1-5-1(b) (b) 175 mm x 100 mm x 75 mm(d) 5 E.a.
49c 1-5-1( c ) (c) 200 mm x 250 mm x 75 mm(d) 15 E.a.
49d 1-5-1( d ) (d) 250 mm x 300 mm x 75 mm(d) 30 E.a.
50 1-5-2. Providing & Erecting 3mm thick Polycarbonate (PC) sheet 5000 Sqinch
with grooving as directed
51 R.A. Supply,installation,testing and commissioning of industrial 8 E.a.
extetion board wall mounted made from 2mm thick CRCA
sheet duly powder coated having industrial metal 3 nos.
20A 1P+N+E P&S and 1 no. 30A 3P+E P&S with 63A
RCBO,10KA " C " and R-Y-B indicating LED Lamps as per
approved by Engineer incharge.

LIGHT FIXTURES AND FANS

52 2-16-2. Supplying and erecting LED indoor fittings with LEDs of
wattage 0.2 Watt to 0.5 Watt assembled on single
MCPCB, with housing used as a heat sink shall be made
of thick sheet Steel conforming to IS: 513/CRCA/
aluminium die cast powder coated and high U.V. &
corrosion resistance with diffuser with company
mark/name 160V to 270V, Power Factor more than 0.9,
THD < 15%,CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt ,LED LED driver
efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE: Below
description have shown ranges of Wattage capacity of
LED fittings.The Engineer incharge may select any
wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

2-16-2(iii) (iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet 5 E.a.
CAT-III
53 2-16-3. Supplying and erecting led lamps with following wattage
capacity of 220 to 240 voltage, minimum 15000 burning
hours life, 500 V in built-surge protection,Polycarbonate
diffuser, mounting suitable for E14 / E27 / B22 lamp
holders, pf >= 0.5

2-16-3(ii) (ii) 5 to 8 watts CAT-III 20 E.a.

54 2-16-4. Supplying and erecting LED indoor fittings with LEDs of
wattage 0.2 Watt to 0.5 Watt assembled on single
MCPCB, with housing used as a heat sink shall be made
of thick sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast powder coated
and high U.V. & corrosion resistance with diffuser housed
in aluminium casted body with company mark/name 160V
to 270V,Power Factor more than 0.9, THD < 15 %,CCT
3000 K to 6500K, Luminaire efficacy> 85
lumens/watt ,LED driver efficiency > 85 %( fitting required
LM-79 & LM-80 Certificates)(NOTE: Below description
have shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select any wattage
capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting clips
complete.IP20
54a 2-16-4(ii) (ii) 11-15 watts, Surge-2 KV CAT-III 128 E.a.
2-16-4(B) (B) LED Panel Light with provision for Plane front frame
with translucent cover fixed to housing complete.IP20

54b 2-16-4(v) (v) 24 watts, 12" x 12" , Surge-2 KV 331 E.a.

2-16-4(F) (F) Spot Light 425 Lumens, Surge-2KV
54c 2-16-4(F-i ) (i) 3 to 7 Watts 8 E.a.
CAT-III
2-16-4(H) (H) Mirror Light 9 Watts, wall mounted minimum 1 feet long 9 E.a.

(I) Adjustable spot light with COB led having aluminium

reflector of following wattage
54d (iii) 15 Watts 16 E.a.
CAT-III
55 2-17-2. Supplying and erecting LED street light / Flood light fittings
with High power White LEDs wattage of 3 Watt and above
assembled on single MCPCB, efficiency more than 130
lm/w and corrosion free High pressure die cast aluminum
housing with smooth finish powder coated and heat sink
extruded aluminium with diffuser and Polycarbonate optics/
lenses, with toughened glass with company mark/name
engraved or embossed 160 to 270 V,Power Factor more
than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity
ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown ranges
of Wattage capacity of LED fittings.The Engineer incharge
may select any wattage capacity between the ranges
shown.)

55a 2-17-2(A) (A) Street Light (IP-65), Surge protection -4KV integral and
,Light must have 440VAC line supply with over-voltage
protection.
2-17-2(iii) (iii) Above 60 to 90 watts 2 E.a.
CAT-III
55b 2-17-2(B) (B) Flood Light (IP-65), Surge protection -4KV integral and
,Light must have 440VAC line supply with over-voltage
protection.
2-17-2(iii) (iii) Above 60 to 90 watts 4 E.a.
CAT-III
55c 2-17-2(vii) (vii) above 200 to 250 watts 4 E.a.
CAT-III
56 2-18-4. Supplying and Erecting Of L.E.D. type High bay fixture
having Power Consumption of following watts with, Input
Voltage 110 - 290 V.AC with full efficiency, Power Factor >
0.9 with 50/60 HZ, CCVC LED Driver used for maximum
power saving, Best Quality Aluminium alloy housing and
aluminium Dome for better heat dissipation, CCT Cool
white (6000K), CRI 80, Beam angle > 120 degrees,
working temperature -20 deg c to +55 deg c, Body IP 65

2-18-4( C ) (C) 150 to 200 watts 40 E.a.

57 5-1-6. Providing & erecting Approved make Power Saving 50 115 E.a.
Watt Ceiling Fan with double ball bearing ISI mark with
Condenser 230 volt A.C. 50 Hz 1200 mm sweep
complete having 3blades with aluminium blades with ,
canopy & 30 cm. down rod erected with earthing.(Make
shall be approved by Engineer in charge))

58 5-1-7. Supply, Installation, Testing and Commissioning of suitable

sweep, BEE 5 Star rated, Ceiling fan with Brush Less
Direct Current (BLDC) permanent ferrite magnet Motor,
class of insulation: B, Rust free 3 nos.Aluminium blades, 2
nos. canopies, shackle kit with earthing provision, copper
winding, Power factor not < 0.9, Service Value (CMM/W)
minimum 6.85, Air delivery minimum 215 CMM, 350
RPM,230v (tolerance as per IS : 374-2019), THD < 10%,
with remote unit for Speed Control and all remaining
accessories including safety pin, nut bolts, washers,
temperature rise = 75 degree C (Max.), suitable for 140 to
285 Voltage and rectifier circuit with surge, over current
and overload protection , 50 Hz, Single phase AC Supply,
earthing etc. Complete as required.[ Make shall be
approved by Engineer in Charge]

5-1-7(B) (B) 1200 mm Sweep (48") 8 E.a.

59 5-2-1. Supplying and erecting 19 / 20 mm. nominal bore Medium 115 Mtr
Class M.S. Pipe down rod erected duly painted for fan
complete with proper insulation without leakage and
earthing.
60 5-2-5. Providing 2.5mm.thick laminated acrylic sheet to cover the 115 E.a.
fan hook or Fan box.
61 5-3-3. Supplying & erecting approved make low noise decorative
exhaust fan having square frame ABS body with inbuilt
lowers & square frame.
200mm with 1350RPM Cat.II 1 E.a.
62 5-3-4. Supplying & erecting single phase approved make
industrial exhaust fan suitable for medium duty ring
mounted low noise operation suitable for medium duty
having following dia size and maximum speed in RPM

[A] 305 mm dia 900 RPM 1 E.a.

CAT-II
63 5-3-6. Providing suitable M.S. louver shutter of the Exhaust fan. 1 E.a.
64 5-4-5. Supplying and erecting approved make double ball bearing
oscillating type Heavy duty bracket fan with Aluminium
Blades A.C. 23OV. 50cy/s wall mounted with height
adjustment and rotary tilting device complete with guard,
wall bracket,mounting accessories as directed.

(A) 450mm 1 E.a.

SWITCHGEARS ( Panels, MCCBs and MCBDBs )
65 Design, fabrication, assembling, supply, installation, testing
and commissioning of cubicle type, wall / Floor mounted
LT panel suitable for 415 V 3 phase, 4 wire 50 Hz AC
supply system fabricated in compartmentised design from
CRCA sheet steel of 2 mm thick for frame work IP 42 and
covers,3 mm thick for gland plates i/c cleaning and
finishing complete 9 tank process in house facility for
powder coating in approved shade, extendable type
TPN aluminium alloy busbars of high condectivity,
DMC/SMC busbar supports, entire panel shall have a
common copper earthbar of size 25mm X 5 mm at the rear
with 2 Nos. earth studs, solid connection from main busbar
to switchgears with require size of aluminium busbar &
control wiring with 1.5 sqmm FRLS insulated copper
conductor cable, cable alleys, cable gland plates i/c
accessrories as per specification and providing
switchgears, metering instruments etc. for following
panel.G.A.Drawing to be approved by EIC or consultant.
( Outgoing connectors must be nut-bolt type. Outgoing
mains for 63Amp MCBs must be of 4 x 16sqmm cu flexible
wires).Incomers Mains for MCBs shall be always from the
busbars.

( a ) Providing cable clamps / supports within distribution

boards cable alley.
( b ) All hinged door shall be earthed through 2.5 sq mm
tinned b raided copper wire.
( c ) Pad locking of MCCB’s handles in “OFF” Position.

( d ) All the C.T.s should be auto short link type.

( e ) All the MCCB's should be with rotary handle.
( f ) All incoming and outgoing air circuit breakers shall be
placed on middle portion of the vertical in single tier
formation.
( g ) Any descripancy found in SLD & Boq , it should be
brought in the notice of the client / consultant, and the
decision will be taken final by Client / consultant.

65a R.A. Main LT PANEL as per SLD (As described above & 1 E.a.
consisting of following items)
INCOMERS:-
(i) 1 no of 800 Amp,50KA FP EDO ACB,50KA With
Adjustable μP Release for O/C,S/C,E/F with 240V under
voltage release,ON Delay Timer 0-30Sec, Push Button
With Element (ACB Close-Trip), LED Type Indicating
Lamp (R-Y-B-ON-OFF)

Metering
 (iii) Digital type 3 phase Multi function Meter CL-1 with
RS-485 PORT, CT 800/5A CL-0.5 ,15VA, 2A SPMCB-
7nos.,TNC Switch,A/M selector switch, Neutral link..

BUSBARS
800 Amps, 415 V, FP Aluminium Busbars with Heat
shrinkable color code insulation sleeves.( 1 sqmm =
0.8Amp )
(i ) 3 no.250A FP,36 KA,415V FP MCCB TM Based with
O/L,S/C /EF protection with spreader link,Rotary
handle,Aux. contact,Shunt release 240V AC,2A SP
MCB,MFM, CT 250/5A CL-1,15VA , Neutral link --R-Y-B
indicating lamps.

(ii ) 3 no.160A FP,36 KA,415V FP MCCB TM Based with

O/L,S/C /EFprotection with spreader link,Rotary
handle,Aux. contact,Shunt release 240V AC,2A SP MCB,
CT 160/5A CL-1,15VA , Neutral link --R-Y-B indicating
lamps.

(iii ) 1 no.160A FP,36 KA,415V FP MCCB TM Based with

O/L,S/C protection with spreader link,Rotary handle,Aux.
contact,Shunt release 240V AC,2A SP MCB, Neutral link
--R-Y-B indicating lamps.
(ii ) 1 no.125A FP,25 KA,415V FP MCCB TM Based with
O/L,S/C /EFprotection with spreader link,Rotary
handle,Aux. contact,Shunt release 240V AC,2A SP MCB,
CT 125/5A CL-1,15VA , Neutral link --R-Y-B indicating
lamps.

( iii ) 7 nos. 63A FPMCB,10kA, C Curve

( v ) 2 Nos. 40A DP MCB,10KA
Misc. Item:- LED Tubelight 6w- 5 nos., Door switch-
10nos., 6ASPMCB-5nos.
65b R.A. U.P.S. Output Panel 1 E.a.
INCOMER:-
1 no.125A FP,25 KA,415V FP MCCB TM Based with
O/L,S/C protection with spreader link,Rotary handle,Aux.
contact,Shunt release 240V AC,2A SP MCB, CT 125/5A
CL-1,15VA , Neutral link --R-Y-B indicating lamps,Digital
Amp & Voltmeter.

BUSBARS
125 Amps, 415 V, TPN Copper Busbars with Heat
shrinkable color code insulation sleeves.( 1 sqmm =
1.6Amp )
Outgoings:-
( i ) 4 nos. 63A FPMCB,10kA, C Curve
( ii ) 1 Nos. 40A DP MCB,10KA
Street Light control Panel
66 6-7-6. Supplying & erecting approved make IP 55 grade
Company fabricated Timer Panel of following capacity
for switch On-Off street lights on time scheduling basis
made from 16G CRCA sheet duly epoxy power painted
inside and outside with hinged doors and locking
arrangement consisting of suitable size of 4 Pole MCB and
4 pole contactor (cat-III)with analog time switch, auto
manual switch of same make and suitable input and
output Bakelite terminals and with door earthing approved
by Engineer in charge.

[C] 63 Amp 1 E.a.

 APFCR PANEL
67 10-4-11. Design, Supplying, installing, testing of factory fabricated
ready made Three phase APFC Panel Cubical Panel
fabrication should be type tested as per IEC 61921,
61439:1&2 Capacitor Duty Contactor for switching as per
following Steps Incomer Switch of MCCB type
Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal
earth fault protection Incomer Switch of MCCB type
Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal
earth fault protection,Copper tinned insulated
Busbar,Cubical panel should be indoor type with IP 43 and
IK 10,Metalized polypropylene film tye3-phase 550Volt
Capacitor,De tuning Reactor for each capacitor,Panel
having Short Circuit and Overload protection,Each step
Capacitor having suitable MCB with Sc, OL, internal earth
fault relay,Each stage having Stage Contactor (Capacitor
load rating),PF regulator master controller having suitable
steps with LCD display, Rs 485 Communication port,
Indication LED Lamps for main incomer and ON-OFF for
each capacitor bank,MS Chanel for Floor mounting, Cable
entry as per site situation,Cooling fans for panel

(B)75KVAR 1 E.a.
68 3-4-1. Pproviding and erecting Approved make Four pole
moulded case circuit breaker having breaking capacity ICU
of 25 KA. at 415 V,having normal current rating up to 25 A
to 100A. with Fixed thermal & magnetic release suitable to
work on A.C. supply 50 c/s. with all internal connections,
spreader tinned copper & complete erected in existing 16
G.M.S. housing.

ICS=100% of ICU only Cat III 1 E.a.

69 3-4-2. Providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 35
KA. at 415 V. having normal current rating 125A. with
Fixed thermal & magnetic release suitable to work on
A.C.supply 50 c/s. with all internal connections, spreader
tinned copper & complete erected in existing 16 G.M.S.
housing.

ICS=100% of ICU only Cat III 1 E.a.

70 3-4-3. Providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 35
KA. at 415 V. having Normal current rating 200A.with
variable Thermal & magnetic release suitable to work on
A.C.supply 50 c/s. with all internal connections, spreader
tinned copper & complete erected in existing 16
G.M.S.housing

ICS=100% of ICU only Cat III 1 E..a.

71 3-11-12. Providing and erecting Sheet Steel powder coated Vertical
MCB distribution board (VTPN) - flush / surface mounted
double door (IP54) fitted with copper insulated busbar,
isolated neutral bar, earth bar and DIN rail, Conforms to IS
8623-1 & 3, IEC 61439-1 & 3, suitable for 250 AMP TPN
MCCB + RCCB as incomer and three phase outgoing as
per following .(The DBs should be used of same company
of MCB to be used)

71a 3-11-12(B) (B)6 way outgoing 1 E.a.

71b 3-11-12( C ) (C)8 way outgoing 2 E.a.
72 3-11-5. Providing and erecting Sheet Steel powder coated MCB
distribution board - flush / surface mounted fitted with
busbar, neutral link, earth bar and DIN rail, Conforms to IS
8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of
same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase

outgoing
72a 3-11-5 ( b ) (b) sheet steel double door (IP-43)
72b 3-11-5(iii) (iii)8 way 4 E.a.
72c 3-11-5(iv) (iv)12 way 1 E.a.
3-11-5(B) (B) three phase incoming and single phase horizontal type
outgoing Per phase isolation type (PPI)

(b) sheet steel double door

72d 3-115(i) (i)4 way 1 E.a.
72e 3-11-5(ii) (iii)8 way 3 E.a.
72f 3-11-5(iv) (iv)12 way 7 E.a.
73 3-11-6. Supplying & erecting Sheet Steel powder coated Cable
end termination Box to be mounted on Top or Bottom of
the MCB Distribution Box for housing/covering Extra wires
& Cables, suitable for following size of MCB DB Box.

73a 3-11-6( C ) (C) Single Phase 8 Way 8 E.a.

73b 3-11-6( E ) (E) Three Phase 4 Way 2 E.a.
73c 3-11-6(G ) (G) Three Phase 8 Way 6 E.a.
73d 3-11-6(H) (H) Three Phase 12 Way 14 E.a.
74 3-10-1(B) providing and erecting Miniature circuit breaker single pole 280 E.a.
6A to 25A suitable to operate on 240 V A.C. system and
having breaking capacity 10 KA to be erected in existing
box. confirming to IS 8828/1996 with ISI Mark CAT-III

75 3-10-2. Providing & erecting 240 V MCB double pole switch for
motor & inductive load (C Curve) having 10 KA breaking
capacity & confirms to IS : 8828 in existing box having
following capacity
75a 3-10-2(A) (A) 6 to 32 Amp. 2 E.a.
CAT-III
75b 3-10-2(B) (B) 40 Amp. 2 E.a.
CAT-III
76 3-10-6. Providing & erecting 415 V MCB three Pole for Motor &
Inductive Load (C Curve) having 10KA breaking capacity
& confirms to IS :8828 in existing box having following
capacity
76a 3-10-6 ( A ) (A) 6 to 32 Amp. 11 E.a.
CAT-III
76b 3-10-6(C ) (c)63 Amp. 13 E.a.
CAT-III
77 3-10-5. Providing & erecting 415 V MCB Four Pole for Motor &
Inductive Load (C Curve) having 10KA breaking capacity
& confirms to IS :8828 in existing box having following
capacity
77a 3-10-5(a) (A) 6 to 32 Amp. 3 E.a.
CAT-III
77b 3-10-5(b) (c)63 Amp. 13 E.a.
CAT-III
78 3-12-1. providing and erecting Approved make RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA and Short
Circuit withstand capacity of 10 KA and suitable for
operation on single phase 240 V,50Hz. having
characteristic of quick action & tripping with all advance
feature & do not incorporate any electronic component. for
following Max. rating erected as directed

78a 3-12-1(i) (i) 25 Amps.DP 2 E.a.

CAT-III
78b 3-12-1(ii) (ii) 40 Amps.DP 2 E.a.
CAT-III
78c 3-12-1(iii) (iii) 63 Amps.DP 30 E.a.
CAT-III
79 3-12-2. Providing and erecting Approved make RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA and Short
Circuit withstand capacity of 10 KA and suitable for
operation on 3 phase and neutral 415V,50Hz. having
characteristic of quick action & tripping with all advance
feature & do not incorporate any electronic component for
following Max. rating erected as directed.

3-12-2(ii) (ii) 40Amps. FP 2 E.a.

CAT-III
80 3-13-3. Providing & erecting Medium Voltage Danger Notice Board 25 E.a.
sticker as per language suggested by engineer incharge of
standard size as per IS-2551
81 3-13-4. Providing & erecting High Voltage Danger Notice Board 8 E.a.
sticker as per language suggested by engineer incharge of
standard size-as per IS 2551
EARTHINGS
82 3-14-1. Providing and erecting required size Aluminium strip for 40 Kg
earthing of H.T. , OCB / ACB / Transformer, LT panel
board, Motors etc. using copper clamp.
83 3-14-2 Providing and erecting required size HOT deep Galvanised 650 Kg
iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT
panel board, Motors etc. using proper clamp.

84 3-14-3 Providing and erecting required size Copper strip for 65 Kg

earthing of H.T. OCB / ACB/ Transformer, LT panel board,
Motors etc. using copper clamp.
85 3-14-4. Providing and erecting Annealed bare Copper wire 8 to 16 5 Kg
SWG.
86 3-14-5 Providing and erecting HOT deep Galvanised iron strip 60 Kg
wire 8 to 16 SWG.
87 3-14-6A Providing and erecting Pipe type earthing having 150 1 E.a.
cms.long and 2.5 cms. dia. galvanised iron pipe with
coupling and buch buried in specially prepared earth pit
complete with necessary 8 SWG earth wire.

88 3-14-9. Supplying & erecting earth pit of minimum bore dia.150mm

size approved make Earthing Electrode consisting Pipe-in-
Pipe Technology as per IS 3043-1987 made of corrosion
free hot dipped G.I.Pipes having Outer pipe dia of 50mm
having 80-200 Micron galvanising, Inner pipe dia of 25 mm
having 200-250 Micron galvanising, connection terminal
dia of 12mm with constant ohmic value surrounded by
highly conductive compound with high charge dissipation
suitable for following type of applications with chamber and
heavy duty cover.(approved make OEM has to submit test
certificate) & having back filling compound of (B) Inner
chemical (CCM Compound)- Resistivity:- 0.2 / meter
testing as per IEC 62561-2017, Voltage drop:- < 1 volt at
no load & dry form, Sulphar content:- <2%(C) Back fill
Compound :- Earthing compound should be capable to
retain moisture for long time Necessary test report must
be submitted.

3-14-9(c ) (c) For Electrical Installation covering Transformer 3 E.a.

Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive
Computer System(like Automation, SCADA) i.e
independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.

89 3-14-10. Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-1987
made of corrosion free hot dipped G.I.Pipes having Outer
pipe dia of 80 mm having 80-200 Micron galvanising,
Inner pipe dia of 40 mm having 200-250 Micron
galvanising, connection terminal dia of 14 mm with
constant ohmic value surrounded by highly conductive
compound with high charge dissipation suitable for
following type of applications with chamber and heavy
duty cover.(approved make OEM has to submit test
certificate including value of earth resistane of installation.

90 3-14-10(C ) [C] For Electrical Installation covering Transformer 2 E.a.

Neutrals, Lightning arrester Earthing, A.C.Plant &
Sensitive Computer System(like Automation,
SCADA)i.e. independent Earthing located in other than
normal soil i.e. Soft Rock, Marshy Soil etc..
-Length of Pipe : 3 Mtrs.
-Back filling Compound :2 nos Bags of 25 Kg.

CABLES AND CABLE TERMINATIONS

91 4-3-3. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe of following size of cables

91a (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) 250 Mtr

91b (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) 20 Mtr
91c (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) 25 Mtr
91d (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) 15 Mtr
91e (G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core) 210 Mtr
92 4-3-4. Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured
cable multistrand / Solid Aluminium conductor for 1.1 KV.
to be laid on wall with necessary clamps or in existing
trench / pipe of following size of cables

92a 4-3-4 ( B ) (B) 4 core 6 Sq. mm 20 Mtr

92b 4-3-4 (C ) (C) 4 core 10 Sq. mm 20 Mtr
93 4-3-5. Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe of following size of cables

93a 4-3-5 ( A ) (A) 4 core 16 Sq. mm 580 Mtr

93b 4-3-5 ( B ) (B) 4 core 25 Sq. mm 150 Mtr
94 4-4-4. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand / Solid Copper conductor for 1.1 KV. to
be laid on wall with necessary clamps or in existing
trench / pipe at road crossing or floor of following size of
cables.

94a 4-4-4(A) (A) 4 core 2.5 Sq. mm 650 Mtr

94b 4-4-4(B) (B) 4 core 4 Sq. mm 100 Mtr
94c 4-4-4( C) (C) 4 core 6 Sq. mm 270 Mtr
95 4-4-5. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Copper conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe at road crossing or floor of following size of cables.

4-4-5(A) (A) 4 core 10 Sq. mm 990 Mtr

96 4-6-1. Providing and, fixing heavy duty flange type brass cable
gland with rubber ring for PVC insulated armoured cable
complete with out going tails, insulating tape etc for
following size of cables.
96a 4-6-1 ( A ) (A) 2 to 4 core 2.5 / 4 Sq. mm 30 E.a.
96b 4-6-1 B ) (B) 2 to 4 core 6 Sq. mm 12 E.a.
96c 4-6-1( C ) (C) 2 to 4 core 10 Sq. mm 26 E.a.
96d 4-6-1( D ) (D) 2 to 4 core 16 Sq. mm 16 E.a.
96e 4-6-1( E ) (E) 2 to 4 core 25 Sq. mm 2 E.a.
97 4-6-3. Providing and, fixing heavy duty flange type brass double
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables.

97a 4-6-3(B) (B) 3 & 1/2 core 35/50 Sq. mm 6 E.a.

97b 4-6-3( C ) (C) 3 & 1/2 core 70 Sq. mm 2 E.a.
97c 4-6-3 ( D ) (D) 3 & 1/2 core 95 Sq. mm 4 E.a.
97d 4-6-3 ( E ) (E) 3 & 1/2 core 120 Sq. mm 2 E.a.
97e 4-3-6 ( F ) (F) 3 & 1/2 core 150 Sq. mm 10 E.a.
98 4-7-1. Solder less crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.

98a 4-7-1 ( C ) (C) 16/25 Sq.mm. 8 E.a.

98b 4-7-1 ( D ) (D) 35/50 Sq.mm. 30 E.a.
98c 4-7-1 ( E ) (E) 70 Sq.mm. 10 E.a.
98d 4-7-1 ( F ) (F) 95 Sq.mm. 12 E.a.
98e 4-7-1 ( G ) (G) 120 Sq.mm. 6 E.a.
98f 4-7-1 ( H ) (H) 150 Sq.mm. 30 E.a.
99 4-11-1. Providing and fixing approved make Perforated C type
cable tray. Made from sheet steel. The cable tray should
be single or double bended as per required and as per IS
2062/1079 and shall be coated with hot dip galvanizing as
per IS 2629/4759. with max 17.5% perforation with
coupler plate / Fish plate and GI hardware like nut - bolt
and washers etc. erection with necessary
support( included) as per Specification and as per
instruction of engineer in charge..

99a 4-11-1 ( 1 ) (1) 50 X 50 X 1.6 mm Thick 35 Mtr

99b 4-11-1 ( 2 ) (2) 100 X 50 X 1.6 mm Thick 95 Mtr
99c 4-11-1 (3 ) (3) 150 X 50 X 1.6 mm Thick 180 Mtr
99d 4-11-1 ( 5 ) (5) 300 X 50 X 2.0 mm Thick 180 Mtr
100 6-1-1. Supplying & erecting Galvanized M.S pipe post “B” class 2 E.a.
88.9 mm O.D 4 mtr. Long duly painted with two coats of
aluminium paint complete with metallic base plate of 300
mm x 300 mm x 4mm thick for using as a compound light
pole with approx. weight 32 Kg.

101 6-1-3. Supplying & erecting Steel tubular pole (Swaged)

confirming to IS - 2713 (Part-II) 1980. Manufacturing
process of steel tubular pole should be as per IS
specification. Basic steel tube should be ISI Marked. Pole
should be painted by one coat of Zinc comet Primer and
two coat of Aluminium /approved paint to be erected on /
in existing Foundation. The length of poles are as below.

6-1-3 ( A ) (A) 7.5 mtr. Long Swaged Steel tubular pole 2 E.a.
(i) pole as per IS code 410-SP-4 with 300 X 300 X 4 mm
base plate. (Approximate Pole weight 67 Kg) For burial
erection
102 6-5-2a Providing and erecting Street Light pole bracket
comprising main B Class MS pipe of 4.2 cm/require
outside dia. complete with suitable B Class M.S. sleeve
tubing of approx. 45cms.length and suitable for 76.5 mm
/80mm / required size of pole top having sufficient
fasteners for fixing the brackets and having spread of
1.5.mtr. length with 110 deg.with vertical plane & suitable
welded stays, reducer and with check nuts complete
painted with one coat of Red oxide / PU base primer and
two coats of Aluminium / PU paint. paint with following nos
of arms.

102a 5-1 A ) [A] Single Arm Bracket 1.5 Mtr 1 E.a.

102b 5-1 B ) [B] Double Arm Bracket 1.5 Mtr 1 E.a.
103 9-5-1. Supplying & erecting approved make Automatic liquid 2 No
level controller 6A. with sensor testing as per
instruction of Engineer in charge on site complete with
wiring connection with existing wires , with copper
conductor from pump to upper and lower tank.
104 1-4-5. Supplying and erecting Flexible PVC insulated multistrand
multicore 1.1 kv grade ISI marked copper wires of
following size to be erected as directed.

1-4-5 ( e ) e) 1.50 Sq.mm 3 core round PVC sheathed 180 Mtr

105 1-3-2. Providing and erecting ISI mark Medium class RIGID PVC
PIPES of following size complete to be erected on/in wall
or ceiling erected with necessary PVC fittings & Junction
boxes fixed with adhesive solution & Clamps with following
dia of pipes, in approved manner as directed .

1-3-2 (a) (a) 20 mm 180 Mtr

106 8-13-2. Providing & erecting water cooler having storage capacity
150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient
temp of 45˚ C. The outlet temp. of the water should drop
by 15˚C within a hour, The water cooler should be
comprising of hermetically sealed compressor, fan motor,
condensing unit, water tank surrounded by evaporating,
coil, thermostats, relay etc.complete with necessary inlet &
outlet connection. The body of water cooler will be made
from Stainless Steel.

107 8-13-6. Supplying & erecting 5 stage single reverse osmosis water
purification system with M.S. powder coated frame,
prefilter housing with 'O' ring presediment filter GAC filter,
carbon filter suitable buster DC pump capacity 80 psi,
mention with 40 psi inline type post carbon filter auto low &
high pressure switches with following size of storage tank
& LPH capacity & erected as directed

8-13-6 ( B ) [B] 25 Ltr / Hr with 30 Ltr. Storage Tank 1 No

108 9-4-2. Providing & erecting open well horizontal mono block
pump set with cast iron body, complete for three phase
submersible motor having
[C] For 3 HP 3 phase open well horizontal mono block 3 No
pump set suitable for 85 LPM to 270 LPM @ 11 mtr to 33
mtr head suitable for 50/65 mm dia delivery pipe.
CAT-II
109 9-5-2. Supplying & erecting approved make motor
control cubical panel (Direct - on - line) made
from 16 G. CRCA sheet duly epoxy powder painted
inside and outside with hinged doors and locking,
arrangement consisting of suitable size of ON- OFF
isolator (AC - 3/23duty) main fuses, single phasing
preventer, indicating lamps for R- Y - B phases,
overload relay, Automatic water level controller,
Ammeter, Voltmeter each with two way selector
switch incoming, wires duly socket crimped, main
contactor & overload relay, start - stop push buttons,
to be erected on angle iron frame grouted on wall
as directed. The isolator, overload relay & contactors
will be of L & T, Siemens or BCH make only.

9-5-2 ( a ) (a) DOL up to 5.0 H.P. 3 No

110 R.A. Supplying, Installation, Testing and commissioning 3HP, 2 No
440V, 3Phase, 100-600LPM, 2900RPM Sewarage
submersible pumping sets of CI casing & impeller, SS
shaft, including with inbuilt water level sensors for
operating the pumps automatically and all accessories
suitable for operation on 220 V-240 V, single phase, 50
Hz. AC supply etc. as reqd.

> 35 mm solid handling capacity,Minimum Capacity -

100-60050 LPM,Minimum Head 3-17 Mtr with 10 Mtr
cable
111 7-19-10. Supplying and erecting approved make online Un- 1 No
S.O.R. interruptible Power Supply system with IGBT Based
2021/22 rectifer and Inverter & sealed maintenance free batteries.
Three phase Input and Three Phase output with Inbuilt
Isolation transformer with 0.9 load power factor with
battery, over under voltage output with over load & short
circuit protection equipment. The system housed in CRC
sheet duly powder coated paint with following capacity &
with Following size of batteries for 30 Min Backup
(Minimum 28800 VAh)
30 KVA UPS with 120 AH, 20 Nos.
Battery

112 R.A. Charges for doing liasioning work for obtaining the 1 JOB
necessary clearances from the Electrical inspector /
competent Authorities for the total Electrical installation,
Elevator Inspection,co-ordinating with various agencies. All
necessary drawings, calculations, test certificates, etc. as
required by these authorities shall be prepared and
furnished by the EPC Vendor. Any
modification/rectification as required by these authorities
shall be carried out by theEPC Vendor at free of cost. The
fees required to be paid to these authorities for inspection
shall be borne by Owner on production of documentary
evidences.

113 13-1-R Supply ,installing , commissioning and testing of M.R.L.

Passengers Elevator 8 to 10 passengers as per R & B
S.O.R ( Category - Premium ) having following
specifications:- Ground+ 2 upper floors
Supplying, Erecting, Testing & Commissioning the
passenger lift having following main features:
[1] GEAR LESS LIFT DRIVE comprising of High Starting
torque Lift 3 phase 440 V
A. C. Permanent Magnet Synchronous motor of proper
rating with high efficiency shall be used.
[2] Micro processor based / PLC, ACVVVF, vector
control drive with encoder feedback closed loop
system shall be used for lift car and door operation which
shall be full collective selective operation hall call
demand response, UP/DOWN hall stops, Main, Up/
Down Contactor with overload and phase reversal relay
and safety controls.
[3] Car with M S platform with bracings of adequate size
and to sustain the impact load cabin + passenger with
safety factor of fire for steel and side panels of Stainless
steel of sheet of grade 304 duty. Car ceiling will be S.S.
finishes with aesthetic appearance with LED ceiling
lights. Car flooring shall be of anti skid PVC with
choice of colour of engineer in charge. Car doors shall
be of stainless steel grade 304, hairline finish with centre
opening / telescopic automatic doors. Car panel will also
be S.S. 304 finished with emergency stop device,
mechanical door safety device, facility of auto/
attended mode. All car panel buttons and all floor
switches must be with brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour shall
be fully automatic centre opening/ telescopic opening
made of hairline finish steel grade of 304 with key holes
and infrared curtains with Unlocking facility from outside
[5] Appropriate battery operated emergency light in the
car along with alarm switch shall be provided. Also,
Emergency Light & Fan should start immediately without
any Time Delay as soon as power fails.
[6] Digital scrolling indicator system for up-down
arrow along with floor position indicator shall be
provided inside the car and at all floors.
[7] Full height infra red curtain with multiple cross /
crossing light beams shall be provided.
[8] Automatic Rescue Device (ARD) shall be provided
accordingly of passenger capacity with Manual Rescue
Operation ( Manual Cranking Facility).
[9] Audio visual indication in the lift car showing over
loading shall be provided such that doors kept open till
excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic
sleep timer shall be provided.
[12] Voice annunciator with suitable music shall be
provided in lift car.
[13] Self diagnostics system for operational and safety
parameters shall be provided in control panel.
[14] Mechanical over speed governor with governor
calibration as per actual site parameters and
submission of calibration certificate submission, door
key holes in the floor doors, fireman switch shall be
provided.
[15] Lift machine hoisting arrangement in the lift machine
room and monkey ladder for lift pit should be provided by
the lift agency, along with the other steel structure works,
foundations for the machine etc…
[16] In the hoist way fascia plate shall be provided without
any extra cost, where ever required as / if directed by
engineer in charge.
[17] Permanent wiring with necessary safety devices
like RCCB in all circuit, Over Voltage Under Voltage
protection and THD eliminator in circuit for lift
machine room and lift well with proper numbers of
light points, with fixtures, exhaust fan and plug points
shall be provided by the agency. Only 3 phase Power
Supply shall be made available by department in lift
machine room. Necessary Earthing as per Lift
Act/Rules shall be arranged by Lift Agency.
[18] Any civil/ electrical works for additional and
alteration in lift shaft and machine room related to
erection of lift shall be made by lift agency without any
extra cost. (granite/marble fixing around all landing door
openings are not in lift agency’s scope.)
[19] Agency has to provide all working drawings and
documents and liaison services for obtaining all
necessary permission from lift inspector and other
authorities. [20] acrylic
transparent licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of Gujarat lift &

escalator act 2000, lift agency has to provide
1. Car top safety barricade
2. Push & talk communication system.
3. Fireman's switch operation at Ground Floor.
4.carrying out third party lift inspection
during/after lift erection and provide report by third party
authorized by concern licensing authority 5.agency
has to provide third party insurance upto completion of free
maintenance period and submit the document for the
same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible
when view from inside cabin.
[22] For Physically Handicapped person Full Length
Handrails of hairline finish steel grade of 304 should be
provided at appropriate height on the Rear & Side Wall
Panels in Lift Car.

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category
1. Advanced control system dual 64 bit embedded
microprocessor with CANBUS Serial Communication
mode including Regenerative power efficient operation,on
site programming facility, Anti nuisance, Pte-opening,
BMS/RMS with necessary online real time monitoring
system having necessary connectivity for remote
monitoring & other suitable supporting hardware &
software devices to fulfil the purpose.

2. Floor Indication LCD Display with call registration & brail

mark with arrival gong and hall lantern & TFT Screen in the
car with MP3 Voice Announcer.
3. CAR Panel should be Scratch resistive SS Moonrock
finish / Hair Line / Honeycomb for car and all Doors, All
landing doors must have fire rating up to 2 hours and car
door must have multi-level crisscross beam door
protection.
 4. To & fro communication system & wiring (i.e. car ,
control room & guard room ) and Each elevator are
equipped with remote monitoring system.agency has to
provide mobile app and user id and password for
monitoring

8/10 passengers Ground + 2 upper floors with Rated

Speed of 1.0 m/sec -
(C) With General PLUS ADDITIONAL SPECIAL 2 No
FEATURES attached herewith. Prem. Cat.
114 10-5-1. SITC of Vertical Air Termination Solid aluminium with 4 No
Base- 10 mm dia and 1000 mm long. Air Termination Base
tested for conditioning, Ageing Test & Lightning impulse
current withstand test: 100 kA of 10/350µs waveform in an
accredited Third party laboratory as per 6.3 & 6.4 of IEC
62561-1 2017 protocol with MAST 34mm dia 3000 mm
long- Cold Galvanized

115 10-5-2. SITC of 8 mm dia solid Aluminium Conductor for roof top 30 Mtr
mesh grid and tested as per IEC 62561- 2 conducted in
the Govt. accredited thirty party laboratory to meet the
requirement of IS/IEC 62305 with Required Accessories -
Aluminium Holding clamp at every 1 mtr distance,
Aluminium/SS cross splicer at every crossing of Alu.
conductor, Expansion piece with connectors at every 20
mtr distance, Aluminium straight Splicer to connect
conductors. All Accessories should be tested as per IEC
62561-1 2018 Cl. 6.3 for conditioning & Ageing Test & 6.4
for Lightning impulse current withstand test: 100 kA of
10/350µs waveform(Ageing & Electrical test ) conducted in
a sequence manner & tested in the Govt. accredited Third
party laboratory to meet the requirements of IS/IEC 6230

116 10-5-3. SITC of 10 mm MS Round Solid Conductor having smooth 40 Mtr

surface Should be tested and use exclusively for lightning
protection (Vertical Riser/Down Conductor which shall be
concealed in Column) to meet the requirement of IS IEC
62305 With Accessories - Earthing stud of dimension SS-
75mm OD plate with 10mm dia tail connector used in
structural steel ring earthing system to meet the
requirements of IS/IEC 62305. (For Interconnecting the
Column and the Terrace AL Conductor / Strip/Flat), SS
Cross Connector to connect Earth fixing point to vertical
raiser/Down conductor, SS Straight Splicer at every 4 Mtr
to connect MS conductor in column, Bonding /Rebar
Clamp at every 3 mtr suitable for interconnecting round
conductor with reinforcement inside the concrete for
structural earthing system, SS connector -To connect
external conductor 8- 10 mm with earth fixing point. All
Accessories should be tested as per IEC 62561-1 2018
Cl. 6.3 for conditioning & Ageing Test & 6.4 for Lightning
impulse current withstand test: 100 kA of 10/350µs
waveform(Ageing & Electrical test ) conducted in a
sequence manner & tested in the Govt. accredited Third
party laboratory to meet the requirements of IS/IEC 6230
117 10-5-4. SITC of Galvanized Steel Flat 25x6 mm thickness from 100 Mtr
earth electrode directly in ground as required. Zinc
coating: 500 g/m square (Approx:70 micron coating) tested
and used exclusively for lightning protection earthing
system and ring equipotential bonding.

118 10-5-5. SITC of 14.2 mm dia 3 mtr long Earth electrode of High 4 per set
tensile steel electrode with 250 micron copper bonding & 1
bag of Carbon fill Based environment friendly backfill
tested as per IEC 62561-7 in NABL accredited Laboratory
and suitable stainless Steel double sided clamp. Eco
Friendly rust proof heavy duty weather proof Polyethylene
Earth Pit Chamber with following dimensions :254 mm dia
(top), 330 mm dia (bottom) & 260 mm (height).

ROOFTOP SOLAR PLANT

119 DSR Design, fabrication, assembling, supply, installation, testing 150 KWp
( E&M)2019 and commissioning and Operation & Maintenance for a 5-
Item for solar Years , of Total 25 Kw capacity Grid connected Solar PV
photovoltaic Plant under Rooftop net Metering at Chankheda
power plant Ranbasera Building , Ahmedabad Municipal Corporation.

Supply, Installation, Testing and Commissioning of ongrid

Solar Photovoltaic Power Plant conforming to MNRE
specifications as amended, consisting of Mono/Poly
Crystalline silicon solar cells, net metering facility,
necessary protections, earthing, mounted on Aluminium/GI
structure of suitable strength with following components
complete as required:-

a) Solar Photovoltaic Module of capacity 330 Wp or above,

manufactured in India, conforming to IS 14286/IEC 61215,
IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar
Photovoltaic Module conversion efficiency shall not be less
than 16.5%. PV modules used in solar power plants/
systems must be warranted for their output peak watt
capacity, which should not be less than 90% at the end of
10 years and 80% at the end of 25 years.

a) Power Conditioning Unit (PCU) of 350-800 V DC Input

voltage range and 400 V AC, three phase, 4 wire, 50Hz +/-
2.5 Hz, output voltage suitable to generate AC Power with
efficiency not less than 97%, total harmonic distortion less
than 3% and suitable for ambient temperature from 0 to 50
degree C. The PCU shall adjust the voltage and frequency
level to suit the Grid Voltage Frequency.

c )Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with

IP 65 protection and termination arrangement for incoming
and outgoing cable along with glands, lugs and other
accessories etc. as required.
e) Lightning and surge voltage protection.
 f )Connections & Interconnections by supplying & fixing
required size XLPE insulated copper conductor 1.1 kV
grade armoured power and control cables between solar
modules, main power cable to grid supply PCU unit along
with supplying & fixing of necessary channel/conduit lugs
and other accessories etc. as required.

HVLS FANS
120 R.A. Supply,installation,testing and commissioning of HVLS Fan 8 No
16 ft PMSM advance technology with out gear box
Industrial ceiling fan with control panel and all accessories
having following specifications.
Size:-4.9 Mtr/ 16 Feet,Dia., Aviation aluminium alloy Profili
V2 Blades-5Nos.,PMSM Direct driveMotor has IP 55
protection, H-Class insulation, 52 poles,120NM
Torque,noise level < 38DB only, power 0.75Kw, Rated
supply voltage 415Volts AC, Rated speed 80 r / Min,Air
Volume 10000 CMM,coverage area 600sqmtr.IP66 -
Dustproof, waterproof, moisture-proof control system.

Mounting Structure to install above fan For Hanger Shed

and Scaffolding or Scissor lift up to Roof Heightwill be
inContractor scope
121 9-6-6. Supplying submersible pump set suitable for bore of 150
mm dia or more having 3 phase motor capacity not less
than 10 HP with following capacity.
9-6-6 ( C ) [C] 25 stage 160 to 100 LPM discharge at 185 to 220 mtr 1 No
head for 50 mm dia delivery pipe
CAT-III
122 9-7-1. Providing and erecting ISI marked PVC insulated PVC
Sheathed Flat flexible Submersible copper cable
approved make of following Size.
9-7-1 ( C ) (C) 3 Core x 4 Sq. mm 440 Mtr
123 9-5-5. Supplying & erecting approved make motor control cubical
panel [Star delta] made from 16G CRCA sheet duly epoxy
powder painted inside and outside with hinged doors and
locking with suitable size of ON - OFF isolator (AC 3 / 23
duty) main fuses. Digital volt and current meter (in a single
unit) with micro controller based control unit and current
sensing single phasing preventer electronic overload
protection, over voltage (Programmable) protection and
under voltage (Programmable) protection, prod less dry
run protection programming facility for setting of all
parameter like overload current, high voltage limit, low
voltage limit, dry run limit with digital indication on seven
segment LED display for any fault like over load, high
voltage, low voltage, dry running single crimped, electronic
star delta timer, feather touch start / stop push buttons to
be erected on angle iron frame. Grouted on wall the
contactors will be of L& T, Siemens , BCH make only)

9-5-5 ( C ) (C) S/D up to 12.5 H.P. 1 No

124 9-7-2. Providing Water proof straight Joint in PVC insulated flat
flexible copper cable by using insulating material, water
proofing material, & making the joint complete.

9-7-2 ( A ) (A) Up to 10Sq. mm 2 No

Total Cost for Electrical Work of Hanger Buil
Say Total Cost for Electrical Work of Hanger Bui
at AMRELI

CTRICAL )

1% Labour Rate with

RATE Amount
Cess L.C.

1300000 13000 1313000 1313000.00

495430 4954.3 500384.3 500384.30
2470551 24705.51 2495256.51 2495256.51

210000 2100 212100 212100.00

1800 18 1818 45450.00

17070 170.7 17240.7 17240.70

9350 93.5 9443.5 28330.50

847 8.47 855.47 51328.20

222 2.22 224.22 2242.20

70 0.7 70.7 2121.00
28 0.28 28.28 282.80

2600 26 2626 5252.00

7700 77 7777 15554.00

150 1.5 151.5 303.00

250 2.5 252.5 505.00

3600 36 3636 7272.00

350 3.5 353.5 707.00

250 2.5 252.5 757.50

1100 11 1111 1111.00

262 2.62 264.62 21169.60

90 0.9 90.9 5454.00

928 9.28 937.28 168710.40

10088 100.88 10188.88 81511.04

12375 123.75 12498.75 49995.00

90 0.9 90.9 40905.00

210 2.1 212.1 16968.00

400 4 404 4040.00
307 3.07 310.07 3100.70

463 4.63 467.63 123921.95

663 6.63 669.63 83703.75

492 4.92 496.92 131683.80

742 7.42 749.42 3747.10

875 8.75 883.75 1767.50

266 2.66 268.66 45672.20

133 1.33 134.33 36269.10

167 1.67 168.67 1686.70

137 1.37 138.37 1383.70

178 1.78 179.78 10067.68

233 2.33 235.33 470.66
178 1.78 179.78 359.56
28 0.28 28.28 1131.20
200 2 202 1010.00
222 2.22 224.22 10089.90
344 3.44 347.44 1737.20

455 4.55 459.55 20679.75

166 1.66 167.66 670.64

553 5.53 558.53 6702.36

759 7.59 766.59 7665.90
26 0.26 26.26 5777.20
36 0.36 36.36 49086.00
60 0.6 60.6 3030.00

23 0.23 23.23 1393.80

29 0.29 29.29 4393.50
40 0.4 40.4 1616.00
51 0.51 51.51 3090.60

34 0.34 34.34 2747.20

40 0.4 40.4 3232.00

476 4.76 480.76 57691.20

1471 14.71 1485.71 44571.30

2042 20.42 2062.42 30936.30

1721 17.21 1738.21 3476.42

229 2.29 231.29 2312.90

394 3.94 397.94 795.88
514 5.14 519.14 1038.28
273 2.73 275.73 551.46
630 6.3 636.3 2545.20

68 0.68 68.68 135986.40

90 0.9 90.9 336330.00

123 1.23 124.23 6211.50

162 1.62 163.62 9817.20
262 2.62 264.62 1323.10

62 0.62 62.62 3131.00

101 1.01 102.01 5100.50
157 1.57 158.57 6342.80
262 2.62 264.62 21169.60
334 3.34 337.34 3373.40

51 0.51 51.51 26270.10

74 0.74 74.74 26159.00
85 0.85 85.85 9443.50
118 1.18 119.18 150166.80

68 0.68 68.68 3434.00

194262 1942.62 196204.62 196204.62

1000 10 1010 60600.00

21 0.21 21.21 45601.50

43 0.43 43.43 10857.50
140 1.4 141.4 21210.00

139 1.39 140.39 11231.20

222 2.22 224.22 8968.80
521 5.21 526.21 21048.40

51 0.51 51.51 7726.50

1108 11.08 1119.08 1119.08

1532 15.32 1547.32 1547.32
1960 19.6 1979.6 3959.20
3855 38.55 3893.55 3893.55

50 0.5 50.5 1010.00

84 0.84 84.84 424.20
97 0.97 97.97 1469.55
122 1.22 123.22 3696.60
3 0.03 3.03 15150.00

19030 190.3 19220.3 153762.40

380 3.8 383.8 1919.00

145 1.45 146.45 2929.00

550 5.5 555.5 71104.00

935 9.35 944.35 312579.85

1050 10.5 1060.5 8484.00

400 4 404 3636.00

1420 14.2 1434.2 22947.20

7735 77.35 7812.35 15624.70

7880 78.8 7958.8 31835.20

14020 140.2 14160.2 56640.80

12000 120 12120 484800.00

2070 20.7 2090.7 240430.50

3370 33.7 3403.7 27229.60

125 1.25 126.25 14518.75

20 0.2 20.2 2323.00

1990 19.9 2009.9 2009.90

2400 24 2424 2424.00

430 4.3 434.3 434.30

 5782 57.82 5839.82 5839.82

1067680 10676.8 1078356.8 1078356.80

66380 663.8 67043.8 67043.80

19930 199.3 20129.3 20129.30

255000 2550 257550 257550.00

7210 72.1 7282.1 7282.10

9410 94.1 9504.1 9504.10

18950 189.5 19139.5 19139.50

11590 115.9 11705.9 11705.90
13815 138.15 13953.15 27906.30

1346 13.46 1359.46 5437.84

1742 17.42 1759.42 1759.42

2732 27.32 2759.32 2759.32

3986 39.86 4025.86 12077.58
4525 45.25 4570.25 31991.75

380 3.8 383.8 3070.40

580 5.8 585.8 1171.60
805 8.05 813.05 4878.30
930 9.3 939.3 13150.20
130 1.3 131.3 36764

350 3.5 353.5 707.00

385 3.85 388.85 777.70

685 6.85 691.85 7610.35

835 8.35 843.35 10963.55

695 6.95 701.95 2105.85

860 8.6 868.6 11291.80

2300 23 2323 4646.00

2610 26.1 2636.1 5272.20

3100 31 3131 93930.00

3080 30.8 3110.8 6221.60

30 0.3 30.3 757.50

40 0.4 40.4 323.20

262 2.62 264.62 10584.80

90 0.9 90.9 59085.00

928 9.28 937.28 60923.20

928 9.28 937.28 4686.40

90 0.9 90.9 5454.00

430 4.3 434.3 434.30

10088 100.88 10188.88 30566.64

12375 123.75 12498.75 24997.50

327 3.27 330.27 82567.50

434 4.34 438.34 8766.80
565 5.65 570.65 14266.25
623 6.23 629.23 9438.45
847 8.47 855.47 179648.70

143 1.43 144.43 2888.60

160 1.6 161.6 3232.00

175 1.75 176.75 102515.00

219 2.19 221.19 33178.50

314 3.14 317.14 206141.00

422 4.22 426.22 42622.00
592 5.92 597.92 161438.40

786 7.86 793.86 785921.40

37 0.37 37.37 1121.10

43 0.43 43.43 521.16
43 0.43 43.43 1129.18
54 0.54 54.54 872.64
59 0.59 59.59 119.18

87 0.87 87.87 527.22

120 1.2 121.2 242.40
152 1.52 153.52 614.08
163 1.63 164.63 329.26
222 2.22 224.22 2242.20

17 0.17 17.17 137.36

23 0.23 23.23 696.90
28 0.28 28.28 282.80
46 0.46 46.46 557.52
52 0.52 52.52 315.12
70 0.7 70.7 2121.00

355 3.55 358.55 12549.25

420 4.2 424.2 40299.00
495 4.95 499.95 89991.00
725 7.25 732.25 131805.00
3768 37.68 3805.68 7611.36

8465 84.65 8549.65 17099.30

730 7.3 737.3 737.30

1070 10.7 1080.7 1080.70
2750 27.5 2777.5 5555.00
 51 0.51 51.51 9271.80

26 0.26 26.26 4726.80

15250 152.5 15402.5 15402.50

15355 153.55 15508.55 46525.65

9020 90.2 9110.2 27330.60

 21500 215 21715 43430.00

1917500 19175 1936675 1936675.00

65000 650 65650 65650.00

1794780 17947.8 1812727.8 3625455.60

11000 110 11110 44440.00

350 3.5 353.5 10605.00

850 8.5 858.5 34340.00

180 1.8 181.8 18180.00

7000 70 7070 28280.00

61060 610.6 61670.6 9250590.00

210965 2109.65 213074.65 1704597.20

47850 478.5 48328.5 48328.50

170 1.7 171.7 75548.00

17160 171.6 17331.6 17331.60

220 2.2 222.2 444.40

ost for Electrical Work of Hanger Building in Rs. = 29332557.36
l Cost for Electrical Work of Hanger Building in Rs. = 29332557.00
 Construction of Hanger at AMRELI

ABSTRACT SHEET (HVAC )

SR. NO. SOR NO DESCRIPTION QUANTIT PER

Y UNIT

HVAC
Note:-Premium category:O-General, Mitsubishi electric
1 SOR 8-3-1. Providing and erecting approved make split air-conditioning
unit consisting of copper condensing unit with fan motor,
hermetically sealed rotary compressor with accessories etc.
duly connected separately erected evaporating unit and
blower motor with its accessories by means of extra
supplied proper insulated copper tubing,drain PVC pipes
suitable for ( cost includes powder coated Stand, Eco
Friendly green gas charging, 15A plug top & Remote
Control) with necessary core cutting.

For 3 Star Rating of current year with Premium

Category
1-a SOR 8-3-1 (a ) [a] For 0.8 to 1.0 Ton Capacity 6 E.a.
1-b SOR 8-3-1 (b ) (b) for 1.5 ton capacity 18 E.a.
1-c SOR 8-3-1 (c ) (c) for 1.7 to 2.0 ton capacity 13 E.a.
2 SOR 8-3-3. Providing and erecting approved make Cassette type split
air-conditioning unit consisting of condensing unit with fan
motor, hermetically sealed scroll/rotary compressor with
accessories etc. duly connected separately erected
evaporating unit and blower motor with its accessories by
Eco friendly Green gas charging & Internal copper wiring &
Remote control ( 3 star and above of current year) with
necessary core cutting.

SOR 8-3-3 ( C ) (C) for 2 ton capacity 4 E.a.

3 8-3-5. Supplying and erecting insulated pair of soft copper tubing 380 RMT
open or concealed including power and control
cable,necessary PVC drain pipes for Split AC machine up
to 4 TR capacity
4 8-3-6. Supplying and installing MS angle , powder coated /
Painted standard type of wall/floor stand mount for outdoor
unit of split AC of following capacity, erected with
necessary hardware materials as directed.
8-3-6 ( A ) (A) 25mm*25mm*3mm thick M.S angle suitable for upto 2 37 E.a.
TR. Capacity of ac machine
5 8-8-4. Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm
thick.nitrile rubber insulation.
5a SOR 8-8-4-B 40 mm Dia 140 RMT
5b SOR 8-8-4-D 25 mm Dia 140 RMT
6 SOR 8-12-3 carry out RCC Core cutting- up to 100 mm dia./300mm thick 37 Job
Wall/beam/slab with providing PVC pipe of 3 mm thick
inside and necessary finishing on both ends of wall .
7 R.A. Supply & Installation of Under Deck Insulation material shall 125 Sqmtr
be chemically cross linked closed cell polyethylene foam
(XPE) insulation material & as per detail specifications - 20
mm Thick with factory laminated UV barrier film

8 3-11-12. Providing and erecting Sheet Steel powder coated Vertical

MCB distribution board (VTPN) - flush / surface mounted
double door (IP54) fitted with copper insulated busbar,
isolated neutral bar, earth bar and DIN rail, Conforms to IS
8623-1 & 3, IEC 61439-1 & 3, suitable for 250 AMP TPN
MCCB + RCCB as incomer and three phase outgoing as
per following .(The DBs should be used of same company
of MCB to be used)

3-11-12 ( B ) (B)6 way outgoing 1 E.a.

CAT-III
9 3-11-5. Providing and erecting Sheet Steel powder coated MCB
distribution board - flush / surface mounted fitted with
busbar, neutral link, earth bar and DIN rail, Conforms to IS
8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of
same company of MCB to be used) suitable for

(b) sheet steel double door

9a 3-11-5(iii) (iii)8 way 2 E.a.
CAT-III
9b 3-11-5(iv) (iv)12 way 2 E.a.
CAT-III
3-4-4. Providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 35 KA.
and above at 415 V . having normal current rating 250A.
with variable thermal & magnetic release suitable to work on
A.C.supply 50 c/s. with all internal connections, spreader
tinned copper & complete erected in existing 16 G.M.S.
housing.

ICS=100% of ICU only Cat III 1 E.a.

3-10-6. Providing & erecting 415 V MCB three Pole for Motor &
Inductive Load (C Curve) having 10KA breaking capacity &
confirms to IS :8828 in existing box having following
capacity
(c)63 Amp. 6 E.a.
CAT-III
10 3-10-5. Providing & erecting 415 V MCB Four Pole for Motor &
Inductive Load (C Curve) having 10KA breaking capacity &
confirms to IS :8828 in existing box having following
capacity
3-10-5 ( c ) (c)63 Amp. 4 E.a.
CAT-III
11 3-10-2. Providing & erecting 240 V MCB double pole switch for
motor & inductive load (C Curve) having 10 KA breaking
capacity & confirms to IS : 8828 in existing box having
following capacity
(A) 6 to 32 Amp. 40 E.a.
CAT-III
12 3-12-1. providing and erecting Approved make RCCBs conforming 12 E.a.
to IS: 12640 and having sensitivity of 30 mA and Short
Circuit withstand capacity of 10 KA and suitable for
operation on single phase 240 V,50Hz. having characteristic
of quick action & tripping with all advance feature & do not
incorporate any electronic component. for following Max.
rating erected as directed

13 4-3-3. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe of following size of cables
4-3-3 ( E ) (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) 60 Mtr
14 4-4-5. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Copper conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench / pipe
at road crossing or floor of following size of cables.

4-4-5 ( A ) (A) 4 core 10 Sq. mm 220 Mtr

15 1-4-1. Providing and erecting Mains with 1.1 KV grade FRLS PVC
insulated ISI marked stranded Copper conductor wire in
following type of pipe to be erected concealed in /flushed
on wall/ceiling, with 1.5 sq. mm copper conductor FRLS
PVC insulated stranded wire of green colour for earth
continuity of following size

(A) With medium class Rigid PVC pipe and accessories

1-4-1 ( b ) (b) 2 wire 2.5 sq. mm 800 Mtr

16 1-4-2. providing and erecting Mains with 1.1 KV grade FRLS PVC
insulated ISI marked stranded Copper conductor wire in
following type of pipe to be erected in / on wall / ceiling with
2.5 sq. mm copper conductor FRLS PVC insulated stranded
wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

1-4-2 ( a ) (a) 2 wire 4 sq. mm 650 Mtr

17 4-6-3. Providing and, fixing heavy duty flange type brass double
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables.

4-6-3 ( D ) (D) 3 & 1/2 core 95 Sq. mm 2 E.a.

18 4-6-1. Providing and, fixing heavy duty flange type brass cable
gland with rubber ring for PVC insulated armoured cable
complete with out going tails, insulating tape etc for
following size of cables.
4-6-1( C ) (C) 2 to 4 core 10 Sq. mm 8 E.a.
19 4-7-1. Solder less crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.

19a 4-7-1 ( D ) (D) 35/50 Sq.mm. 2 E.a.

19b 4-7-1 ( F ) (F) 95 Sq.mm. 6 E.a.
20 4-7-2. Solder less crimping type Copper lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.

4-7-2( B ) (B) 10 Sq.mm 40 E.a.

Total Cost for HVAC Work of Hanger Buildin
Say Total Cost for HVAC Work of Hanger Buildi
AMRELI

VAC )

RATE 1% Rate with Amount

Labour L.C.
Cess

41750 417.50 42167.50 253005.00

55550 555.50 56105.50 1009899.00
62840 628.40 63468.40 825089.20

64500 645.00 65145.00 260580.00

960 9.6 969.6 368448.00

1300 13 1313 48581.00

110 1.1 111.1 15554.00

90 0.9 90.9 12726.00
1550 15.5 1565.5 57923.50
900 9 909 113625.00

11590 115.9 11705.9 11705.90

3986 39.86 4025.86 8051.72

4525 45.25 4570.25 9140.50

24470 244.7 24714.7 24714.70

835 8.35 843.35 5060.10

860 8.6 868.6 3474.40

350 3.5 353.5 14140.00

3100 31 3131 37572.00

565 5.65 570.65 34239.00

786 7.86 793.86 174649.20

90 0.9 90.9 72720.00

123 1.23 124.23 80749.50

152 1.52 153.52 307.04

43 0.43 43.43 347.44

23 0.23 23.23 46.46

 46 0.46 46.46 278.76

11 0.11 11.11 444.40

Cost for HVAC Work of Hanger Building in Rs. = 3443071.82
tal Cost for HVAC Work of Hanger Building in Rs. = 3443072.00
 Construction of Hanger at AMRELI

ABSTRACT SHEET (ELECTRICAL )

SR. NO. SOR NO DESCRIPTION QUANTITY PER UNIT RATE

CCTV System Work

1 R.A. Supply,installation,testing and commissioning outdoor 8 No 7755
Bullet camera having Hi-Focus Image Sensor 1/2.7”
Progressive Scan CMOS Sensor , Effective Pixels
2560×1440 Electronic Shutter Speed 1 s ~ 1
/100000s , Lens 2.8mm @F2.0, horizontal field of
view:110º 3.6mm @F2.0, horizontal field of view:89º
6mm @F2.0, horizontal field of view:56º Wide Dynamic
Range Digital WDR Product Features 4MP ( 2560 ×
1440) H.265 coding , Max. resolution: 2560 × 1440
Video Compression H.265/H.264/ MJPEG , Sub
Stream 60Hz:720P/D1/CIF(1~30fps);
50HZ:720P/D1/CIF(1~25fps), 60Hz:D1/CIF/480x240
(1~30fps); 50HZ:D1/CIF/480x240 (1~25fps) Network 1
RJ45 10M/100M Base-TX Ethernet, Power Supply
DC12/ PoE Power Consumption <4W, Operating
Conditions -20°C ~ 55°C,(-4ºF ~131ºF) .Make : UNV,
Samsung, Honeywell.

2 R.A. Supply,installation,testing and commissioning of indoor 30 No 7755

Dome camera Hi-Focus Image Sensor 1 / 2.7”
Progressive Scan CMOS SensorImage Sensor,
Effective Pixels 2560 x 1440, Electronic Shutter Speed
1/25s~ 1 /100000s, Minimum Illumination 0.011 lux
@F1.2, AGC ON; 0 lux with IR,Lens 2.8mm @F2.0,
(fixed lens), horizontal field , Video Compression H.265
/ H.264 , Resolution 4MP (2560 x1440),3MP (2304 x
1296), 1080P 1920x1080), 720P (1280x720), D1, CIF,
480x240 Audio Compression G711A / U, Network
RJ45, Audio MIC IN x 1, Power Consumption < 4W
Operating Conditions -20°C ~ 55°C (-4°F~131°F)
Humidity .Make : UNV, Samsung, Honeywell.

3 R.A. Supply, Installtion , Testing & Commissioning of ptz 4 No 73932

Camera with 120dB WDR, IP66, 30X optical zoom,
HLC,Smart functions, EIS, 2MP Resolution, Ultra 265
Compression, PoE - yes, Micros SD Card - Yes, Audio
- 1/1, Alaram I/O - 1/1, IR Range -150Mtr , 1/2.8"
CMOS, ICR, 1920x1080:30fps, Ultra
265/H.264/MJPEG, Triple streams,
AC24V/DC24V/PoE, Micro SD card slot, Alarm in/out
1/1, Audio, -40-65℃, IP66, 30x optical zoom(4.5 ~
135mm), IR range: up to 150m, IR anti-reflection
window.Make : UNV, Samsung, Honeywell.
4 R.A. Supply, installation, testing and commissioning of 320 2 No 50204
Mbps Bit Rate Input Max (up to 40-ch IP video), 4
SATA interfaces, alarm I/O: 16/4, 2U case,19". The
Specifications are as following:-
IP video input : 40-ch , Up to 12 MP resolution, Two-
way audio : 1-ch, 3.5mm, Incoming bandwidth : 320
Mbps, Recording resolution :
12MP/8MP/6MP/5MP/4MP/3MP/1080p/UXGA/720p/V
GA/4CIF/DCIF/2CIF/CIF/QCIF, CVBS output : 1-ch,
BNC (1.0 Vp-p, 75 Ω), resolution: PAL: 704 × 576,
NTSC: 704 × 480, HDMI output resolution : HDMI1:
4K (3840 × 2160)/60Hz, 4K (3840 ×
2160)/30Hz, 2K (2560 × 1440)/60Hz, 1920 ×
1080p/60Hz, 1600 × 1200/60Hz, 1280 × 1024/60Hz,
1280 × 720/60Hz, 1024 × 768/60Hz, VGA: 2K (2560 ×
1440)/60Hz, 1920 × 1080p/60Hz, 1600 × 1200/60Hz,
1280 × 1024/60Hz, 1280 × 720/60Hz, 1024 ×
768/60Hz, Audio output : 1 x RCA, Decoding format :
IH+265/H.265/H.264, Live view/Playback
resolution
:2MP/8MP/6MP/5MP/4MP/3MP/1080p/UXGA/720p/VG
A/4CIF/DCIF/2CIF/CIF/QCIF, Synchronous playback :
16-ch, Network protocols : TCP/IP, ICMP, HTTP,
HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP,
PPPoE, NTP, UPnP, SMTP, IGMP, QoS, IPV4, IPV6,
Multicast, ARP, UDP, SNMP, SSL, Telnet, RTMP,
NFS, SATA : 4 SATA interfaces, Capacity : Max. Up
to 10TB capacity for each HDD, Network interface : 2,
RJ-45 10/100/1000 Mbps self-adaptive Ethernet
interface, Serial interface : RS-232; RS-485, USB
interface : 2, Alarm in/out : should support (Specified by
Bidder), Power supply : 100 to 240 VAC, Working
temperature : -10 to +55º C, Working humidity : 10 to
90 %,Chassis : 19-inch rack-mounted 2U chassis

5 R.A. Supply, Installation , Testing and Commissioning of 2 No 8615

4TB Surveillance Hard Disk . Make:- WD,
SEAGATE,Mitsubishi
6 R.A. Supply, Installation, Testing and Commissioning of 55" 2 No 113625
4K LED Display . Should be provides elaborate 4K
picture quality down to the tiniest details. Should have
Built in Wi-Fi , Built in Web Browser, HDMI CEC
Enabled, Built in HDR, Built in Android Apps, Hotel
Mode, Audio ARC. Should be 16:9 ASPECT RATIO,
RESOLUTION : UHD (3840*2160), DISPLAY AREA
(H X V): 1209.6(H)*680.4 (V) mm, 78°/178º (HN)
VIEWING ANGLE (HN). CONNECTION TERMINAL:
RFIN: 1*Side, DTVIN:1*Side, AVIN: 1mini *Side, USB
INPUT (2.0 SUPPORT): 2*Side (USB 2.0), HDMI
INPUT: 3*Side (HDMI 2.0), RJ-45: 1*Side, USB
DEVICE SUPPORT: Picture Format: PNG/BMP,
AUDIO OUTPUT POWER (RMS) : 20W (1 O+1 OW),
Make : Panasonic/Barco/Samsung

7 R.A. supply installation testing and commissioning of Rack

(Final size is to be calculated by contractor base on
drawings and actual requirement of site)

Rack are fabricated from good quality of CRCA sheet,

bended, welded and powder coated.
Welded frame integrated with side wall and vented top
cover with Fan Mounting provision, rear side of
enclosure having wall mounting provision, front glass
door with lock and key provides the visibility and
security.

Rack is conforms to DIN 41494 or equivalent

standards. Equipment mounting are Din standard slots.

Rack is tobe provide with Power distribution units of

required 5A, 3 pin socket with switch, Horizontal /
Vertical cable manager, Cooling fan, Hardware,
Horizontal / cantilever tray etc. complete as per site
requirement.

7a Wall mount System Rack 4U 1 No 5540

7b Wall mount System Rack 9U 1 No 9845
8 1-4-8. Supplying & erecting approved make LAN cable of
following size in existing pipe as per direction
1-4-8( C ) [C] CAT - 6 1850 No 51
9 7-12-12. Providing & erecting Optical Fiber cable should be
ISO/IEC- 11801 , Outer sheath FRLSZH Shall be 9µ,
Single mode OS2 steel armoured cable as per
ISO/IEC- 11801 Shall be able to meet Gigabit & 10
Gigabit Ethernet performance requirement specified by
IEEE 802.3z (1000 Base-X) & IEEE 802.3ae
(10GBase-X) Shall have water blocked construction to
prevent water absorption and consequent damages.
Water blocking with flooding Gel and water blocking
yarn shall comply for IEC 60332-3 for flame retardant,
IEC 61034- 2 for low smoke & IEC 60754-2 for toxicity
& acidity. Tensile load should be 2700 Newton or
higher Optical Parameters – SM, (a) Attenuation @
1310nm(max) ≤ 0.34 dB/Km, (b) Attenuation @
1550nm(max) ≤ 0.22 dB/Km with neccessory
connections

(A) 6 core Single mode 150 Mtr 74

10 1-3-2. Providing and erecting ISI mark Medium class RIGID
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner
as directed

1-3-2(b) (b) 25 mm 950 Mtr 36

11 7-11-4. Supply, Installation Testing & Commissioning 20 ft 2 E.a. 14018
HDMI Interface Cable as per the detailed Specifications
supports transmission of 4K Signals as per the detailed
Specifications
12 R.A. Supply, installation, fixing, testing and commissioning 38 E.a. 440
of PVC Junction box for CCTV Camera, IP65, outdoor
application. Junction Box size will be as per vendor's
requirement and site condition.

FIRE ALARM and Detection System

13 7-13-2. Supplying, installation, testing and commissioning of
micro processor based intelligent addressable main fire
alarm panel having IS or BS (EN 54) (Vds approved) or
NFPA 72 (UL/ULC/FM approved) with latest
Ammendment with central processing unit with the
following loop modules and capable of supporting not
less than 240 devices (including detectors) and
minimum 120 detectors per loop and loop length up to
2 km, network communication card, minimum 320
character graphics/ LCD display with touch screen or
other keypad and minimum 4000 events history log in
the non volatile memory (EPROM), power supply unit
(230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed
maintenance free batteries with automatic charger. The
panel shall have facility to connect printer to printout log
and facility to have seamless integration with
analog/digital voice evacuation system (which is part of
the schedule of work under SH: PA System) and shall
be complete with all accessories . The panel shall be
compatible for IBMS system with open protocol
BACnet/ Modbus over IP complete as per specification.
(B) 2 Loop Panel

Two Loop Panel 1 No 239000

14 SOR 21/22 SITC of Analog Multi-Criteria Sensor Features, Low 77 No 5310
7-10-68. profile - only 2" high including base, variable sensitivity
from 0.7 to 4% obs/Ft Simple and reliable device
addressing, Automatic compensation for sensor
contamination , Built in Fire test feature, Two built-in
power/alarm LEDs, programmable non-polling LEDs,
Non-directional Smoke chamber, Vandal resistant
security locking feature, Approved by UL and FM

15 SOR 21/22 SITC of Fixed Temperature/Rate of Rise sensor, 12 No 4602

7-10-70.. Low profile-only 2.00" high, including base, simple and
reliable device addressing method, Rate of rise
temperature threshold = 15° F/Min, Adjustable
threshold temperature = 135° - 190°, Approved by UL
and FM

16 7-10-19. SITC of sensor common mounting base, includes 90 No 531

stainless steel contacts, slim profile - only 8mm, quick
connection via square cable clamps, facility for remote
indicator, Approved by LPCB

17 7-13-6. Supplying, installation, testing & commissioning of 24 No 270

response indicator on surface/recessed MS Box having
two LED, metallic cover complete with all connections
etc as required.
18 7-10-75. 3 No 8850
SITC of Fast Response Contact Monitoring Module.
The Module shall have UL 864 9th Edition Listed,
Single Input contact monitor, can be programmed to
monitor Normally Open (NO) or Normally Closed (NC)
contacts, operates on Class A or Class B SLC loop,
Accepts up to 12 AWG wire. Approved by UL and FM

19 R.A. Supply, installation, testing & commissioning of 4 No 275000

EN approved Intelligent Analog Addressable
flame detector with ASA Technology and 3
Infrared Sensors. Detector shall communicate 3
danger levels for differentiated alarm activation.
Detector should have the protection category of
IP67- Approved Makes - Notifier, Honeywell,
Kidde, Esser

20 7-13-15. Supplying, installation, testing & commissioning of 12 No 3860

addressable manual call point having IS or BS (EN 54)
(Vds approved) or NFPA 72 (UL/ULC/FM approved)
with Latest Amendment complete as required.

21 7-13-16. Supplying, installation, testing & commissioning of 12 No 3500

addressable horn cum strobe having IS or BS (EN 54)
(Vds approved) or NFPA 72 (UL/ULC/FM approved)
with Latest Amendment complete as required.

22 7-13-8. Supplying, installation, testing & commissioning of fault 8 No 3260

isolator having IS or BS (EN 54) (Vds approved) or
NFPA 72 (UL/ULC/FM approved) with Latest
Amendment complete with base as required.

23 7-13-22. Supplying & laying of 2x1.5 sqmm fire alarm armoured 1480 Mtr 145
cable, 600/1000V rated with annealed copper
conductor having XLPE insulation, steel wire
armouring & FRLS outer sheath complete as
required.

24 R.A. SITC of Battery for the above fire alarm panel 2 No 1500
PUBLIC ADDRESS SYSTEM
25 R.A. SITC of Ceiling loudspeaker, 6W Suitable for 47 No 3200
speech and music reproduction Light weight ABS
material Easy to install Optional back-box
Unobtrusive design

26 R.A. Supply, installation, testing & commissioning of 4 No 3410

6W wall mount speaker with excellent speech &
music reproduction
- Max Power: 9W,Rated Power: 6Watts, Power
Tapping: 6/3/1.5W
- Effective frequency range(-10 dB) : 200 Hz to
15KHz
- SPL at rated power (1Khz at 1 m) 96 dB
- Opening Angle 1 KHz / 4 KHz (-6 dB): 150/70 -
Approved Makes - Honeywell-X-618, ATIS-
IDA8, BOSCH-Prisadio
27 S.O.R. 1 No 13200
2021/22
7-3-3. Supplying & erecting Approved make or equivalent
Amplifier having following specification:
Power Output :250W (RMS) (300W Max.)
inputs : 6 Misc. & 2 Aux.
frequency Response :50-1500HZ I3db
Tone Controls :Cut & Boost type
LED Meter :5 LED Arrays
The amplifier suitable to operate 240V A.C.& 24volt
D.C. (Battery) with automatic changeover from AC to
Battery operation, duly protected by wrong Battery
Polarity connections.

28 S.O.R. 1 No 11300
2021/22 Supplying & erecting Approved make or equivalent
7-3-4. Booster Amplifier having power output of 25OW
(RMS,), suitable to obtain combined power output of
two, with 6 mike inputs & suitable to be used
independently as a 250watt amplifier in combination
with mike & mixer. The booster Amplifier shall be
without mike &Aux. input channels, The system shall
be suitable to operate on 24OV. A.C. & 24 Volts D.C.
Battery.

29 S.O.R. Supplying & erecting Approved make Mixing Console 1 No 14500

2021/22 7- having channels, Audio mixer with. Echo facility for live
4-1. performance, Auditorium & stadiums, having following
features & facilities.
(a)input Channels :- Each channel has separate
6.25mm size balanced phone jack for mike & line
for balanced & unbalanced signals.

(b)Individual gain control for sating optimum level

for minimum noise.
(c)BASS, MID & TREBLE ‘ controls Separately for each
input channel.
(d)ECHO control for each channel
(e)PAN control for echo channel for left or right output

(f) AUX Control : To control , level of the channel in

final mix to AUX sound output
(g)Channel ON/OFF switch
(h)ECHO Section :- ECHO, reverb & Chorus effect can
be added to all input channel by different setting of
Delay, Reverb & Level control.
(i)Tape section
(j)Aux. send & return For sending Pre-feeder output of
channel for monitoring or adding a special effect unit.

(k)Mono / Stereo output controls

(L)Master faders to control over left & right output

(m) Head phone output for monitoring purpose.

Technical specification
(a)Power Requirement -AC220-24OV 50 Hz DC 24
Volts
 (b)MIC Output Impedance/gain -2 K Ohms/ 62 dB

(c)Line Output Balance/42 dB —- 20 K ohms

(d) Impedance / Gain :- 10Kohms unbalance / 42

dB
(e)frequency Response - 30 Hz- 20 KHz L / R Line
Output ( + 0, -1 dB )
(f)Equalization Bass/ - + / - 12 dB at 100Hz Mid /
Treble 2 KHz / 10 KHz
(g) Outputs, Line Output Line Output Low : -10
dB / -2 dBM Line Output High : 0 dBM / +17 dBM
(775 mv / 5.5 V )
(h) S/N ratio Line Output Level : > 70 dB (0 dB,
0.775V)
The Console shall be mounted on standard Rack, The
channel of following numbers.
(B) 9 Channel Audio Mixer with ECHO
30 S.O.R. Supplying & erecting Approved make four channel 1 No 4200
2021/22 7- Echo Mixer Pre-amplifier with following specification.
4-2. (i) Suitable to operate on 24OV.A.C. & 12 V D.C.
Battery supply
(ii) B.B.D. Delay system ECHO facility on all inputs
through ECHO volume, Repeat & Delay system.
(iii) Peak LED for setting optimum distortion free input
levels
(iv) Two outputs, variable for line & fixed for recording
(v)Compatible with Audio Mixing consoles

31 7-5-3. Supplying & erecting recess wall mounting speaker

with 5W rated input power 3.3 K. Ohms / 3W
impedance, 100 - 10000 Hz frequency response with 6
inch dia. cone type 8 ohms speakers duly fitted in ABS
plastic cabinet of colour match with wall or ceiling of
following size.

(b)Square shaped 260 x 260mm size speaker 8 No 690

32 7-6-5. Supplying, erecting & testing Approved make 2 No 600
Microphone for announcement, speech & general
P.A. application with frequency response of 150 -
10000 Hz having sensitivity 2mv/Pa, & impedance 600
Ohms supplied with quick detachable holder, 6 mtr twin
core cable & PCIM / MCIF connector.

33 DSR 17.5.3.1 Supply and laying speaker cable single pair ,2 core , 1600 Mtr 51
1.5sqmm in existing pipe
34 1-3-2. Providing and erecting ISI mark Medium class RIGID
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner
as directed .

25MM 1000 Mtr 36

35 R.A. Supply, Installation, Testing & Commissioning of XLR 2 No 925
M/F Redaymade Cable (2 Mtr.)
36 R.A. Supply, Installation, Testing & Commissioning of XLR 2 No 1540
M/F Redaymade Cable (5 Mtr.)
37 R.A. Supply, Installation, Testing & Commissioning of 1 Lot 15000
Cable Connector and Accessories for System
ACCESS CONTROL SYSTEM
38 R.A. Supply, installation, testing & commissioning of UL 4 Nos. 55,480.00
Listed 2 reader IP Enable Interface with , with complete
Set of UL Enclosure, Power Supply and Circuit
charging, IP interfaces to be considered based on the
site requirement, Shall support IPv4/v6 - Approved
Makes Honeywell, Lenel, Suprema

39 R.A. Supply, installation, testing & commissioning of 5 Nos. 124,590.00

UL listed Biometric 2.7" LCD, ARM Cortex A9
processor. 512RAM 1:N Mode 500 Users and
expendable to 3000 and 10,000 users with
license. IDs- Approved Makes Honeywell,
Lenel, Suprema
40 R.A. Supply, installation, testing & commissioning of 1 Nos. 1,540.00
Push to Agress switch including surface mounted
back boxes/Concealed GI back boxes.-
Approved Makes - Reputed makes
41 R.A. Supply, installation, testing & commissioning of 2 Nos. 18,480.00
600 LBS Single Leaf EM Lock with LED and
Feedback - Approved Makes - Bell, DORMA,
UNI
42 R.A. Supply, installation, testing & commissioning of 1 Nos. 159,280.00
SQL based VAPT Certified Access Control
Software supporting Above devices with unlimited
user capacity as per technical specifications,
shall support modular architechture. Capable to
support visitor management, contractor
management, Vehical access management
through single database.- Approved Makes
Honeywell, Lenel, Suprema

43 R.A. Supplying, installation, testing and commissioning 1 Nos. 228,510.00

of Client PC - Industry standard Intel based
platform computer system. Intel Core i7 latest
generation, 8 GB of RAM DDR3 ,1 TB SATA II
hard drive for OS and VMS applications, NVidia
card 1 GB graphics card , 1600 x 1200 or higher
screen resolution, 1 X 1000Mbps ethernet
network interface card ,16x DVD+/- RW Drive
alongwith appropriate licenced Operating System,
licenced applications suites from OEM and
application licences as per the technical
specifications etc. as required. - Approved
Makes - HP, Dell, Lenovo

IT NETWORKING SYSTEM
44 7-12-6. SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit 4 No 27258
RJ45/SFP Combo ports Advanced L2 switching and
security features L2+ Static Routing
Optional “standard mode” or “surveillance mode”
management user interface

45 7-12-8. SITC of 8 x 10/100/1000BASE-T PoE ports 2 x Gigabit 2 No 32568

SFP ports
Advanced L2 switching and security features L2+ Static
Routing Optional “standard mode” or “surveillance
mode” management user interface 65W PoE budget

46 7-2-16. Providing & Erecting Netwrok rack with following

capacity with Necessary cooling fan,Cable manager,6A
PDU,equipment rack with necessary mounting
accessories.
46a (A) 9 U 3 No 13500
46b (D) 15 U 1 No 22500
47 R.A. Providing & Erecting Netwrok rack with following
capacity with Necessary cooling fan,Cable manager,6A
PDU,equipment rack with necessary mounting
accessories.
6U 3 No 7500
48 7-12-3. SITC of Jack Panel, fully loaded with 24 nos. UTP 6 No 7800
ports for PCB based IO Jacks (RJ45, TIA-568C
Category-6, Installation and Termination of all 24 nos.
Catergory-6 UTP , unloaded with individually
replaceable 24 nos. Category-6 I/O Jacks complying
with TIA-568.C.2, as per given jack specification Shall
be suitable for loading unshielded & shielded jacks for
different category systems (CAT 6 & CAT 6A)

49 7-12-1. SITC of company fabricated patch cords shall conform

to Cat- 6 & conductor shall be stranded for better
flexibility Shall support network line speeds up to 1
Gbps Shall have RJ-45 jacks.
49a 7-12-1(A) (A) 1 Mtr 70 No 225
49b 7-12-1( B ) (B) 2 Mtr 70 No 263
50 7-12-4. SITC of Faceplate for RJ45 Port with ABS /Metal Body
square plate, dimension as per commercially available
modular office furniture. Shall Have Icons, Shutter,
Screw Cover, Label Cover, Jack holder with
neccessory connections

50a (A) 1-port 65 No 160

50b (B) 2-port 5 No 180
51 1-4-8. Supplying & erecting approved make LAN cable of
following size in existing pipe as per direction
1-4-8( C ) [C] CAT - 6 3500 Mtr 51
52 1-3-2. Providing and erecting ISI mark Medium class RIGID
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner
as directed
 1-3-2( b ) (b) 25 mm 1500 Mtr 36
53 S.O.R. SITC of On-Board Computer OPS (Core i5 1 No 113280
2021/22 Processor, 8 GB RAM, 128 GB SSD) with the
7-16-9. software as per the detailed Specifications
54 R.A. Supply, Installation, Testing and 6 No 71324
Commissioning of Wireless indoor
Access Point supporting Dual band with
802.11a/n/ac (5 GHz) and
802.11g/n (2.4GHz) concurrent operation with
MIMO support 3x3, 3 spatial streams, One
10/100/1000 BASE-TX auto-sensing (RJ45)
PoE port, as per technical specification etc. as
required.- Approved Makes - Dlink, Cisco, HP

Audio-Video System work of Conference Hall

55 R.A. Supply, Installation, Testing and Commissioning of 9 No 28956

Boundary Microphone Should have half-heart-shaped
single-pointing characteristics, Should provide ultra-
quiet electronic switches, Frequency response Should
be 30 to 20k Hz, Sensitivity Should be -34 dB (19.9
mV) at 1V at 1 Pa, Resistance Should be 200 ohms,
Maximum input sound pressure level Should be 130
dB, Should have 68 dB Noise ratio, Phantom Power
Supply DC 11 to 52V DC & 3 mA power consumption.
56 R.A. Supply, Installation, Testing and Commissioning of 1 No 277200
DSP is a powerful digital audio processor with minimum
16 inputs and minimum 8 outputs, with touch screen
operation control interface display. providing the
highest performance 400 MHz/2200 MFLOP processor
capability. Ultra-low noise floor preamplifier circuit, low
distortion analog circuit, 114dB audio AD, DA, provide
high-quality sound quality for the scene. The front panel
of the device must have a volume status display, which
can display the volume status of all input 16 and output
16 channels; the front panel LCD display of the device
can cyclically display the current IP address of the
device, the pre-set number currently used by the
processor, and the pre-set name. The front panel has a
network connection status indicator and an error alarm
indicator. When a serious error occurs, a red alarm can
be flashed. It can be connected to the Android system
and supports smart phones or tablet PCs to control the
software package.Powerful DSP processor capability
Based on the super powerful ADSP-21489 super
powerful DSP processing capability, and based on our
unique core DSP method, Rich audio channels and
control interfaces 1 TCP/IP communication port, 1 RS-
232 communication port, 1 USB communication port,
open third-party control protocol. It can be used in
various large, medium and small professional audio
projects. It can meet the application needs of public
sound reinforcement systems such as theaters, concert
halls, remote video conferences, stadiums, churches,
conference centers, theme parks, etc. a built-in
independent 16-channel extremely low distortion
adaptive feedback suppressor, 16-channel noise gate,
and 16-channel input compressor are realized. , 16-
channel 16-segment PEQ, 16-channel input 48dB
slope high-pass-low-pass filter, 16-channel 1 second
delay, means that you can accurately and carefully set
each input audio channel. 16x8 full matrix mixing,
realizing free mixing of any input channel.
R.A. . Each of the 8 output channels has independent 8-
band PEQ, compressor, 48dB slope high-pass-low-
pass, and 2-second delay.Built-in sine wave, pink
noise, white noise signal generator. 32 Presets can be
stored. Open RS-232, TCP/IP communication protocol
16-channel balanced input audio channel, with Phoenix
plug, should have 16 channels support Microphone
input, each input should supports 48V phantom power
supply, 8 balanced audio output channels with phoenix
plug, must have 8-channel independent adaptive
feedback suppressor, should have automatic mixing,
each channel must have pre-amplifier, noise gate,
compressor, 16-band parametric equalization, delayer,
automatic mixer, Output per channel should be 8-band
parametric equalization, frequency divider, high and
low pass filter, limiter, delayer Should be Built-in signal
generator sine wave signal, pink noise, white noise, on
the front panel displays the IP address and the current
pre-set should be displayed, should have Nominal input
level of +4 dBu line or -40 dBu microphone level and
Microphone preamplifier gain 0-40 dB analog gain,
20dB digital gain Maximum input level should have
+20dBu, Input impedance should have >5 kΩ
balanced, >3kΩ unbalanced, should have Common
Mode Rejection Ratio (CMRR): >70dB @ 1 kHz Pre-
amplified equivalent input noise : <-125 dBu, 2 2Hz-
22kHz , Phantom power supply: +48 V DC ,Audio
output: 8-channel balanced line level, Phoenix plug
Nominal output level: 0 dBu line level Output
impedance: 600 Ω balanced

DSP frequency and processing capacity: 400Mhz,

400MIPS, 2200 MFLOP Sampling
frequency/quantization: 48 kHz, 24Bit ADC, 24Bit DAC,
Frequency response: 20 Hz – 20 kHz, + /- 0. 5 dB,
Dynamic range: 114 dB, ADC, DAC, Total harmonic
distortion: <0.01%; 20Hz ～ 20kHz@+4dBu , Crosstalk
between channels: >-80 dB @ 1 kHz, typical, Power
supply: 100～240VA, 50/60 Hz, 75W.
57 R.A. Supply, Installaton, Testing and Commissioning of 1 No 63840
Power Ammplifier Should have 138v Max Peak Output
Voltage, Frequency Response Should be 20HZ-
20KHZ-3dB@150kHz Should be <0.1% , Damping
Factor Should be > >800, Input Sensitivity Should be
0.775v, Input impedance Should be >20kΩ balanced &
>10k Unbalanced, Should have 3-pin
XLR ,electronically balanced Input connectors, XLR ,3
pin male Link connectors, Should have Clip/Limit,
Signal, Temp/DC, Active LED indicators; Power Should
be 2x1700w at 8 Ω stereo power, 2x1350w at 4 Ω
stereo power, 2x1850w Bridge Mono power at 8 Ω.

58 R.A. Supply, Installation, Testing and Commissioning of 5" 4 No 6270

Two Way Wall Mount Speaker should be with 5" woofer
and 0.5” tweeter two way speaker units, 100V or 70V
Line input, 6.25W-12.5W-25W-50w at 8 ohms Rated
power output, 75-20KHz frequency response, 90dB
SPL.

59 R.A. Supply, Installation, Testing and Commissioning of Pop 1 No 14250

UP Box should provide an extremely simple, affordable
and elegant single-push pop-up multi-connection
solution. By pressing down gently on the lid, the unit
opens and closes pneumatically, fast and easy to install
and flexible to configure, should have HDMI, Audio,
Power, CAT6 inputs.

60 R.A. Supply, Installation, Testing and Commissioning of 1 No 28500

Audio-Visual Switcher 2 x 1 Seamless HDMI Metrix
with Any one of the sources to any one of the 2
displays. Each port support both HDMI and DVI inputs.
1U rack design ,easy installment, DC 12V 3A power
supply. Control via Remote . Control via RS232 .
Operating Temperature Range : 0 to +35°C (32 to
+95°F), Operating Humidity Range : 5 to 90 % RH (no
condensation), Input Video Signal : 0.5-1.0 volts p-p ,
Input DDC Signal :5 volts p-p (TTL), Video Format
Supported : DTV/HDTV:
1080P/1080i/720P/576P/480P/576i / 480i, Audio
Format Supported : LPCM, Input ports :
1xHDMI(standard Type A connector), Output ports :
2xHDMI(standard Type A connector), Power
consumption : 24watts (Maximun).
61 R.A. Supply, Installation, Testing and Commissioning of 1 No 205200
5000 lumens LCD Projector should have Transparent
LCD type panel with Active matrix drive method, 16.3
mm –panel, 16:10 aspect ratio, 1920 × 1200 pixels
resolution, 1.09–1.77:1 throw ratio, 280 W UHM lamp,
16,777,216 colors. It should have 85% center to corner
uniformity, 16,000:1 contrast ratio, 7000 hours lam life.
It should have 10w Inbuilt speaker, ± 25° Vertical
keystone correction, ± 30° horizontal keystone
correction, 37dB operating noise, 0°C (32°F) to +40°C
(104°F) operating temperature, 20% to 80% humidity. It
should have I/O connectors as computer in x 1,
Computer out x 1, Video In x 1, HDMI In x 2, Audio In
(Stereo) x 2, Audio In (Mini Jack) x1, Audio Out x 1,
USB x 1, Serial In x1, and LAN x1. It should Support on
Windows® PCs and Android™ devices, next-
generation Mira cast is a low-latency protocol that
provides high-bandwidth mirroring of video, stills, and
web content with fast connection and a range of
exclusive and practical features for users, up to 10
users can project at any time for open collaboration.

62 R.A. Supply, Installation, Testing and Commissioning of 6 1 No 10260

Ft. Width X 8 Ft. height Instalock Screen should Have
Manual Pull Down wall or ceiling mounted projection
with SELF LOCK screen. This advanced automatic-
locking device, fold and unfold freely without any
hassles is perfect for education facilitates, meeting
rooms, control rooms, business training centers or for
other entertainment purposes. Ceiling mounting options
Easy pull-down mechanism with lock at intervals. There
are also some brackets available that will allow you to
mount your screen off the wall.

63 R.A. Supply, Installation, Testing and Commissioning of 1 No 2850

custom made Ceiling Mount Stand For Projector

64 R.A. Supply, Testing and commissioning of 10 Meter HDMI 2 Pcs 8550

Cable for display. 4K UHD and HD compatible,
99.999% oxygen free copper conductors, Flexible,
durable foil-insulated housing material increases ease
of installation and product life Exceptional high speed
performance for 4K UHD and HD 1080p displays with
3D, Perfect opaque plug end as well as excellent
conductivity and protection against oxidation, Kink
protection and strain relief to protect conductor.
65 R.A. Supply, Testing and commissioning of 1 Meter HDMI 1 Pcs 1368
Cable for display. 4K UHD and HD compatible,
99.999% oxygen free copper conductors, Flexible,
durable foil-insulated housing material increases ease
of installation and product life Exceptional high speed
performance for 4K UHD and HD 1080p displays with
3D, Perfect opaque plug end as well as excellent
conductivity and protection against oxidation, Kink
protection and strain relief to protect conductor.

66 R.A. Supply, Installation, Testing and Commissioning of 1 Pcs 1596

VGA Cable Approved Make List :Digilink/Beldon/D-link

67 R.A. Supply, Installation, Testing and Commissioning of 2 50 Mtr 137.50

core shielded 0.5 Sq.mm Microphone bulk cable.
Approved Make List :Digilink/Beldon/D-link
68 R.A. Supply, Installation, Testing and Commissioning of 1.5 50 Mtr 142.50
Sq.mm 16 AWG, Speaker Cable.
69 R.A. Supply, Installation, Cabling and Commissioning of 50 Mtr 97
STP Cat 6 cable.
70 R.A. Supply Installation Testing & Commissioning of 17U 1 No 19380
600 x 800mm Indoor Floor mount Rack with required
accessories like 6 socket PDU, 2/4 Fan, 2 Hardware
Mounting Packet, 1 Equipment Tray.
71 R.A. Supply, Installation, Testing and Commissioning of 1 Lot 25080
Cable,Connectors & Accessories
72 R.A. SITC of High Performance dual channel UHF wireless 1 No 6050
tie pin/ handdeld microphone available in different
frequencies. Separate volume control for both
channels. One handheld dynamic transmitter and one
Bodypack transmitter, each operating on 2×1.5V AA
pencil cells. Separate balanced audio output from each
channel through XLR connector and an unbalanced
mixed output through 6.3mm (¼”) jack erected as
directed by enginner incharge

Total Cost for ELV Work of Hanger Building

Say Total Cost for ELV Work of Hanger Buildin
1% Labour Rate with
Amount
Cess L.C.

77.55 7832.55 62660.4

77.55 7832.55 234976.5

739.32 74671.32 298685.28

502.04 50706.04 101412.08

86.15 8701.15 17402.3

1136.25 114761.25 229522.5

55.4 5595.4 5595.4

98.45 9943.45 9943.45

0.51 51.51 95293.5

 0.74 74.74 11211

0.36 36.36 34542.00

140.18 14158.18 28316.36

4.4 444.4 16887.2

2390 241390 241390
53.1 5363.1 412958.7

46.02 4648.02 55776.24

5.31 536.31 48267.9

2.7 272.7 6544.8

88.5 8938.5 26815.5

2750 277750 1111000

38.6 3898.6 46783.2

35 3535 42420

32.6 3292.6 26340.8

1.45 146.45 216746

15 1515 3030

32 3232 151904

34.1 3444.1 13776.4

132 13332 13332

113 11413 11413

145 14645 14645

42 4242 4242

6.9 696.9 5575.2

6 606 1212

0.51 51.51 82416

0.36 36.36 36360

9.25 934.25 1868.5
 15.4 1555.4 3110.8

150 15150 15150

554.8 56034.8 224139.2

1245.9 125835.9 629179.5

15.4 1555.4 1555.4

184.8 18664.8 37329.6

1592.8 160872.8 160872.8

2285.1 230795.1 230795.1

272.58 27530.58 110122.32

325.68 32893.68 65787.36

135 13635 40905

225 22725 22725

75 7575 22725
78 7878 47268

2.25 227.25 15907.5

2.63 265.63 18594.1

1.6 161.6 10504

1.8 181.8 909

0.51 51.51 180285

 0.36 36.36 54540
1132.8 114412.8 114412.8

713.24 72037.24 432223.44

289.56 29245.56 263210.04

2772 279972 279972
638.4 64478.4 64478.4

62.7 6332.7 25330.8

142.5 14392.5 14392.5

285 28785 28785

2052 207252 207252

102.6 10362.6 10362.6

28.5 2878.5 2878.5

85.5 8635.5 17271

 13.68 1381.68 1381.68

15.96 1611.96 1611.96

1.375 138.875 6943.75

1.425 143.925 7196.25

0.97 97.97 4898.5

193.8 19573.8 19573.8

250.8 25330.8 25330.8

60.5 6110.5 6110.5

LV Work of Hanger Building in Rs. = 7147286.21

ELV Work of Hanger Building in Rs. = 7147286.00
 Construction of Hanger at AMRELI

ABSTRACT SHEET (FIRE FIGHTING )

2022/23
SR. NO. DESCRIPTION QUANTITY PER UNIT RATE
SOR NO

Design, Supplying,Installation,Testing and

commissioning of Fire-Fighting System.
FIRE PUMPS AND ACCESSORIES
1 DSR (E&M) Supplying, Installation, Testing and Commissioning of 2 SET 404830
2022 electric driven main Hydrant-Sprinkler system fire
18.1.2 pump and Foam System pump suitable for automatic
operation and consisting of following: complete in all
respect as required.

a) Horizontal type, single stage, centrifugal, end suction

pump of cast iron body & bronze impeller with stainless
steel shaft, mechanical seal to ensure a minimum
pressure of 3.5 kg/sq. cm. at highest and farthest outlet at
specified flow of 2850 lpm at 70 Mtr. head conforming to
IS 1520.with suitable size of footvalve confirming to IS
4038, Pressure rating PN2 , preventing entry of foreign
body to pump through suction pipe, perfectly flat seating
surfaces for good sealing.

b) Suitable HP Squirrel cage induction motor, TEFC,

suitable for opertion on 415 volts, 3 phase 50 Hz. AC with
IP 55 class protection for enclosure, horizontal foot
mounted type with Class - 'F' insulation, conforming to IS-
325.

c) M.S. fabricated Common base plate, coupling, coupling

guard, foundation bolts etc. as required.
d) Suitable cement concrete foundation duly plastered
with anti vibration pads.
The pump shall be capable of giving not less than 150%
discharge at ahead not less than 65% of the rated head.

2 DSR (E&M) Supplying, Installation, Testing and Commissioning of 1 SET 616966

2022 diesel engine driven common stand by fire pump
18.2.2 suitable for automatic operation and consisting of
following: complete in all respect as required

a) Horizontal type, single stage, centrifugal, end suction

pump of cast iron body and bronze impeller with stainless
steel shaft, mechanical seal to ensure a minimum
pressure of 3.5 kg/sq. cm at highest and farthest outlet at
specified flow of 2850 lpm at 70 Mtr head conforming to
IS 1520.
 b) Suitable HP, 1500 /1800 RPM water cooled with
radiator, diesel engine conforming to relevant BS & IS
standard complete with auto starting mechanism, 12/24
volts electric starting equipment, 180 AH lead acid battery
with battery stand, exhaust pipe extended upto 6 m.
outside pump house duly insulated with 50 mm thick
glass wool with 1.0 mm. thick aluminium sheet cladding,
residential silencer, instruments and protection as per
specification, stop solenoid for auto stop in the event of
fault with audio indications, painted with post office red
colour etc. as required.

c) One 200 Ltr capacity day oil storage tank fabricated

from 3 mm thick M.S. plates. Tank shall be provided with
inlet, outlet, overflow, air vent, drain connections, filling
connection & level indicator. Tank shall be mounted on a
suitable steel structure (Painted with 2 coats of red oxide
paint). Tank shall be provided with two or more coats of
synthetic enamel paint outside over two coats of red oxide
primer.

d) M.S. Fabricated Common base plate, coupling,

coupling guard, foundation bolts etc. as required.
e) Suitable cement concrete foundation duly plastered
with anti vibration pads.
3 DSR (E&M) Supplying, Installation, Testing and Commissioning of 1 SET 103304
2022 electric driven pressurisation pump suitable for
18.3.2 automatic operation and consisting of following: complete
in all respect as required

a) Horizontal type, single stage, centrifugal, end suction

pump of cast iron body and bronze impeller with stainless
steel shaft, mechanical seal at specified flow of 180 lpm
at 70 Mtr. head conforming to IS: 1520.with suitable size
of footvalve confirming to IS 4038, Pressure rating PN2 ,
preventing entry of foreign body to pump through suction
pipe, perfectly flat seating surfaces for good sealing.

b) Suitable HP Squirrel cage induction motor TEFC type

suitable for operation on 415 volts, 3 phase 50 Hz. AC
with IP 55 Class of protection for enclosure, horizontal
foot mounted type with Class F' insulation, conforming to
IS : 325.

c) M.S. fabricated Common base plate, flexible rubber

coupling, coupling guard, foundtion bolts etc. as required.

d) Suitable cement concrete foundation duly plastered

with anti vibration pads.
4 R.A. Fabrication, Supplying, Installation, Testing & 1 No 310230
Commissioning of electrical control panel of cubical
construction, floor mounted type, fabricated out of 2mm
thick CRCA sheet, compartmentalised with hinged
lockable doors, dust and vermin proof, powder coated of
approved shade after 7 tank treatement process, cable
alley, inter-connection, having switchgears and
accessories mounting and internal wiring, earth terminals,
numbering etc. complete in all respect, suitable for
operation on 415 V, 3 phase, 50 HZ, AC supply with
enclosure protection class IP 42 as required.for above fire
fighting system.

A. Incoming Feeder:-
(i) 1 No of 250 A,35KA, 415V,FP MCCB with
Thermalmagnetic Based Releases having O/C, S/C ,E/F
protection,Digital KWH Meter, Digital ELR 96x96mm with
CBCT, FP Spreader Terminals 1 set= 8 Pcs, Extended
Rotory Handle for MCCB, 240V AC Shunt Trip coil for
MCCB.

(ii) LED type indicating Lamp with suitable rating 2 Amp

SP MCB:- 1 Set (each set comprise of R,Y,B)
(iii) Digital type 3 phase Multi function Meter with suitable
rating of MCB & 3 Nos. of single core epoxy resin cast
type CTs of 250/5 Amps, 10 VA, CL 1.0 ratings -1 Set.

B. Busbar:-
415 V, 300 Amps, TPN Aluminium Busbars with Heat
shrinkable color code insulation sleeves.
OUTGOINGS:-( All outgoing feeders for pumps should
have digital Ammeter with selector switches and LED type
ON,OFF,Trip indicating Lamps )
Main Elect Driven Pump
2 No. of 125A, 25KA FP MCCB, Ics=100%,Extended
Rotory handle with TM release having O/C and S/C
protection with suitable HP fully automatic star/ delta
starter , current sensing type, Single Phase Preventer,
ON/OFF Push Button & LED type Indicating lamps
complete with all accessories and internal wiring required
for automatic operation, selector switch, for local/remote,
auto/manual operation.

JOCKEY PUMP:-
1 no.63A,16KA MCCB Ics=100%,Extended Rotry handle
with TM release having O/C & S/C protection with suitable
HP fully automatic star/ delta starter , current sensing
type, Single Phase Preventer, ON/OFF Push Button &
LED type Indicating lamps complete with all accessories
and internal wiring required for automatic operation,
selector switch, for local/remote, auto/manual operation

Diesel Engine Control.

Control for Diesel Engine comprising:
i) Auto/Manual selector switch & 3 attempt starting device,
timers and relays as required, push buttons, start/stop in
manual mode.
 ii) LED type Indication lamp for High/Low Lub. Oil
pressure, High Water Temp and Engine ON indication.

iii) Battery charger suitable for 12 V/24 V DC with boost

and trickle selector switch, 0-30 V DC volt meter, 0-20
Amp DC Ammeter.
iv) All standard relays, accessories for automatic
operation of diesel engine, wiring with 1.5 sq mm PVC
insulated copper wire between various sensors and
system controller / starter, suitable size cable for battery
charging etc. as required.

System Controller
Designing, Supply, Installation, Testing and
Commissioning of system controller to control operation
of Main Electric Fire Pump, Diesel Pump, Pressurisation
Pump, Terrace Pump in sequence as per specification
consisting of relays, timers, sensors, annunciation window
for fault indication, control wiring complete as
specification.

5 4-3-3. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench /
pipe of following size of cables

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) 60 Mtr 623
6 4-4-2. Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Copper conductor for 1.1 KV. to be laid
on wall with necessary clamps or in existing trench /
pipe at road crossing or floor of following size of cable.

6a 4-4-2( E ) (E) 3 core 16 Sq. mm 60 Mtr 846

6b 4-4-2(C ) (C) 3 core 6 Sq. mm 45 Mtr 459
7 4-2-2. Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured
copper cable 1.1 KV grade to be erected as directed of
following size.
4-2-2 ( A ) (A)7 core 1.5 Sq. mm 80 Mtr 132
8 4-6-1. Providing and, fixing heavy duty flange type brass cable
gland with rubber ring for PVC insulated armoured cable
complete with out going tails, insulating tape etc for
following size of cables.
(B) 2 to 4 core 6 Sq. mm 8 E.a. 43
(D) 2 to 4 core 16 Sq. mm 8 E.a. 54
9 4-6-2. Providing and, fixing heavy duty flange type brass double
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables.

(E) 3 & 1/2 core 120 Sq. mm 2 E.a. 163

10 4-7-1. Solder less crimping type Aluminium lugs conforming to
IS suitable for cable of following size evenly crimped with
high pressure tool & connected to switchgear terminals
with brass/cadmium plated nut bolts in an approved
manner.

10a 4-7-1(E ) (E) 70 Sq.mm. 2 E.a. 28

10b 4-7-1( G ) (G) 120 Sq.mm. 6 E.a. 52
11 1-4-5. Supplying and erecting Flexible PVC insulated
multistrand multicore 1.1 kv grade ISI marked copper
wires of following size to be erected as directed.

1-4-5( e ) e) 1.50 Sq.mm 3 core round PVC sheathed 450 Mtr 51

12 1-3-2.
Providing and erecting ISI mark Medium class RIGID
PVC PIPES of following size complete to be erected on/in
wall or ceiling erected with necessary PVC fittings &
Junction boxes fixed with adhesive solution & Clamps
with following dia of pipes, in approved manner as
directed
1-3-2( b ) (b) 25 mm 450 Mtr 36
13 4-11-1. Providing and fixing approved make Perforated C type
cable tray. Made from sheet steel. The cable tray should
be single or double bended as per required and as per IS
2062/1079 and shall be coated with hot dip galvanizing
as per IS 2629/4759. with max 17.5% perforation with
coupler plate / Fish plate and GI hardware like nut - bolt
and washers etc. erection with necessary
support( included) as per Specification and as per
instruction of engineer in charge..

13a (3) 150 X 50 X 1.6 mm Thick 25 Mtr 495

13b (5) 300 X 50 X 2.0 mm Thick 20 Mtr 725
14 3-14-9. Supplying & erecting earth pit of minimum bore
dia.150mm size approved make Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-
1987 made of corrosion free hot dipped G.I.Pipes having
Outer pipe dia of 50mm having 80-200 Micron
galvanising, Inner pipe dia of 25 mm having 200-250
Micron galvanising, connection terminal dia of 12mm with
constant ohmic value surrounded by highly conductive
compound with high charge dissipation suitable for
following type of applications with chamber and heavy
duty cover.(approved make OEM has to submit test
certificate) & having back filling compound of (B) Inner
chemical (CCM Compound)- Resistivity:- 0.2 / meter
testing as per IEC 62561-2017, Voltage drop:- < 1 volt at
no load & dry form, Sulphar content:- <2%(C) Back fill
Compound :- Earthing compound should be capable to
retain moisture for long time Necessary test report must
be submitted.

3-14-9( c ) (c) For Electrical Installation covering Transformer 1 No 10088

Neutrals, Lightning arrester Earthing, A.C.Plant &
Sensitive Computer System(like Automation, SCADA) i.e
independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.

15 3-14-2 Providing and erecting required size HOT deep 200 Kg 90

Galvanised iron strip for earthing of H.T. , OCB/ ACB/
Transformer LT panel board, Motors etc. using proper
clamp.
16 3-14-5 Providing and erecting HOT deep Galvanised iron strip 10 Kg 90
wire 8 to 16 SWG.
17 8-10-9. Providing and fixing in position the industrial type 6 E.a. 1260
pressure gauges with gun metal / brass valves complete
as required
18 DSR (E&M) Providing and fixing of Pressure Switch in M.S. Pipe line 4 E.a. 1546
2022 18.22 including with Needle Valve.

19 R.A. Supplying, Installation, Testing and commissioning of Air 1 SET 40250

vessel fabricated from 8mm MS plate with dished
ends,dia of 450 mm and height 2000 mm with suitable
supporting legs, outside painted with one coat of primer
and two coats of synthetic enamel paint of approved
shade, complete with one 25mm dia connection from
pump delivery, one 25 mm drain with valve.The air vessel
shall be tested to 1.5 times of working pressure.
Complete as per technical specification & drawing details.

20 R.A. Supplying, Installation, Testing and commissioning of 1 No. 1293600

Horizontal Foam Bladder Tank Foam Bladder Tank
capacity of 2000Ltr made out of SS304 with Nylon
Reinforced Rubber Bladder,having water side piping to
seamless steel pipe 316 Sch. 40 & foam concerntrate
unit with 1 No. Wafer Type ratio Controller ,Pressure
Guage, control valve ,Sight glass etc.
(Without Foam Concentrate)

21 R.A. Supplying, Installation, Testing and commissioning of CI 1 No. 98400

Foam Inline Inductor 150mm dia
22 R.A. Providing & Fixing of AFFF Foam Solution 2400 Ltr. 210
23 DSR (E&M) Supply, installation, testing and commissioning of Deluge
2022 valve ( to be used for water curtains) UL listed with wet
18.26 pilot basic trim assembly for DVA with test and alarm, drip
and drain valve with water motor gong complete as
required.

18.26.4 150MM Dia 1 Set 115434

24 DSR (E&M) Providing,installation,testing and commissioning of water 1 No 701
2022 curtain nozzle 15mm dia nickel chrome plated brass
18.27 BSPT, K-factor as per design consideration complete as
required.
25 DSR (E&M) Providing,installation,testing and commissioning of 1 Set 7369
2022 electric release trim assembly for deluge wall with two
18.28 way solenoid valve, weather proof operation on 24 volts
DC supply complete as required.
26 S.O.R.2021/22 SITC of ABS Manual Call Point with key – break / Re 12 E.a. 975
7-11-63 settable type.
27 S.O.R.2021/22 SITC of ABS Sounder - 24V, 95-105 db APPROVAL: CE 12 E.a. 975
7-11-69 Mark
28 R.A. SITC of fire pump start stop push buttons in box. 12 E.a. 850
29 DSR (E&M)
2022
18.11 Supplying, fixing, testing and commissioning of butterfly
valve of PN 1.6 rating with bronze/gunmetal seat duly ISI
marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
29a 18.11.2 50mm Dia 2 E.a. 3784
29b 18.11.3 65mm Dia 1 E.a. 4302
29c 18.11.4 80mm Dia 1 E.a. 4980
29d 18.11.5 100mm Dia 2 E.a. 6667
29e 18.11.6 150mm Dia 5 E.a. 8960
29f 18.11.7 200mm Dia 6 E.a. 15207
30 DSR (E&M)
2022 Providing, installation, testing and commissioning of non-
18.14 return valve of following sizes confirming to IS:5312
complete with rubber gasket, GI bolts, nuts,washers
etc.as required :
30a 18.14.3 65mm Dia 1 E.a. 6418
30b 18.14.7 150mm Dia 3 E.a. 17786
30c 18.14.8 200mm Dia 1 E.a. 29282
31 DSR (E&M) Providing, laying, testing & commissioning of 'C' class
2022 heavy duty MS pipe conforming to IS 3589/IS 1239
18.7 including Welding, fittings like elbows, tees,
flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe
on the wall/ceiling with suitable clamp/support frame and
painting with two or more coats of synthetic enamel paint
of required shade complete as required :

31a 18.7.1 25 mm Dia. 12 Mtr 744

31b 18.7.4 50 mm Dia 6 Mtr 1281
31c 18.7.5 65 mm Dia 6 Mtr 1614
31d 18.7.6 80 mm Dia 6 Mtr 1885
31e 18.7.7 100 mm Dia 12 Mtr 2555
31f 18.7.8 150mm Dia 18 Mtr 3574
31g 18.7.9 200mm Dia ( wall thickness 6.3mm ) 24 Mtr 5463
31h 18.7.10 250mm Dia ( wall thickness 6.3mm ) 12 Mtr 6659
32 DSR (E&M)
2022 Providing, installation, testing and commissioning of
18.15 stainless steel Y-strainer fabricated out of 1.6 mm thick
stainless steel, Grade 304, sheet with 3 mm dia holes
with stainless steel flange.
18.15.4 200mm Dia 2 E.a. 22265
33 R.A. Supplying, installing ,testing and commissioning of Flow 1 E.a. 76393
meter( Electronic type) on Test line to measure 175 % of
pump flow and suitable to 100 mm dia.

34 R.A. Supply, Installation, Testing and Commissioning of

Forged brass Ball Valves with all fittings required. (PN-
25)
34a 15mm dia 11 E.a. 411
34b 25mm dia. 2 E.a. 890
34c 50mm dia R.O. E.a. 2997
35 R.A. Supplying, installing and commissioning C.I.flanged
pressure relief valve with CI body,suitable flanges, nuts,
bolts, gaskets etc. complete.
a)100 mm Dia

35a 100mm Dia 1 E.a. 22000

35b 150mm Dia 1 E.a. 27500
36 DSR (E&M) Supplying and fixing orifice plate made out of 6 mm thick 8 E.a. 1321
2022 stainless steel (Grade 304) with orifice of required size to
18.13 be fitted between flange & landing valve of external and
internal hydrants to reduce pressure at the outlet to the
level of 3.5 kg/cm2 complete as required.

FIRE HYDRANT SYSTEM

37 DSR (E&M) Providing, laying, testing & commissioning of 'C' class
2022 heavy duty MS pipe conforming to IS 3589/IS 1239
18.7 including Welding, fittings like elbows, tees,
flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe
on the wall/ceiling with suitable clamp/support frame and
painting with two or more coats of synthetic enamel paint
of required shade complete as required :

37a 18.7.8 150mm Dia 170 Mtr 3574

37b 18.7.7 100 mm Dia 140 Mtr 2555
37c 18.7.6 80 mm Dia 20 Mtr 1885
38 DSR (E&M) Providing, laying, testing & commissioning of 'C' class
2022 heavy duty MS Pipe conforming to IS 1239 i/c fittings
18.6 like elbows, tees, flanges, tapers, nuts bolts, gaskets etc.,
in ground including excavation and providing cement
concrete blocks as support, anticorrosive treatment with
coaltar/asphalt tape as per IS 10221, refilling the trench
etc. of following sizes complete as required .( For
HYDRANT )

38a 18.6.2 150MM Dia 18 Mtr 3804

38b R.A. of 18.7.7 100MM Dia 131 Mtr 4777
38c R.A. of 18.7.6 80mm Dia R.O. Mtr 2180
39 DSR (E&M)
2022
18.11 Supplying, fixing, testing and commissioning of butterfly
valve of PN 1.6 rating with bronze/gunmetal seat duly ISI
marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
39a 18.11.4 80mm Dia R.O. E.a. 4980
39b 18.11.5 100mm Dia 2 E.a. 6667
39c 18.11.6 150mm Dia 3 E.a. 8960
40 DSR (E&M) Supplying and fixing Single headed internal / External
2022 hydrant valve with 1 No. 63 mm dia instantaneous FM
18.9 Gunmetal/Stainless Steel coupling and cast iron wheel,ISI
marked, conforming to IS 5290 (type A) with blank
Gunmetal/Stainless Steel cap and chain as required :

18.9.2 Single headed Stainless steel 8 No 6139

41 DSR (E&M) 10 No 1662
2022
18.18.2 Providing Stainless steel ISI marked 63 mm. dia. male
Instantaneous pattern short branch pipes with 20 mm dia.
Nozzle as per IS : 903, suitable for 10 Kg/sqcm operating
pressure and suitable for interconnections to hose pipe
coupling as required.
42 R.A. 12 No 12390
Providing, fixing, testing and commissioning of Wall
mounting swing type first aid Fire Hose Reel with drum,
hanging bracket, 30 M x 25 mm dia high pressure hose
reel tubing as per IS:884 with shut nozzle and ball valve
and all required accessories.
43 R.A. Supplying, Installation, Testing and commissioning of 12 No 5410
weather proof Fire Hose cabinet size 900x
600x300mm to house fire hydrant & hose, including
all other related accessories fabricated from M.S. sheet
(16 Gauge) of fully welded construction having front door
with locking arrangement, partially glazed with 4 mm thick
glass. Cabinet shall be powder coated & painted with
post office red colour
44 R.A. 2 No 2025
Providing, fixing, testing and commissioning of 25 mm dia
Air Release Valve and Ball Valve assembly on top of
each riser for Air release system.
45 DSR (E&M) Supplying and fixing of fire brigade connection of cast
2022 iron body with gun metal male instantaneous inlet
18.19 couplings complete with cap and chain as reqd. for
suitable dia MS pipe connection conforming to IS 904

18.19.2 4 way - 150 mm dia M.S. Pipe 1 No 13974

Automatic Water Foam sprinkler system for
Aircraft Hanger
46 DSR (E&M) Providing, laying, testing & commissioning of 'C' class
2022 heavy duty MS pipe conforming to IS 3589/IS 1239
18.7 including Welding, fittings like elbows, tees,
flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe
on the wall/ceiling with suitable clamp/support frame and
painting with two or more coats of synthetic enamel paint
of required shade complete as required :

46a 18.7.1 25 mm Dia. 315 Mtr 744

46b 18.7.3 40 mm Dia 352 Mtr 1034
46c 18.7.4 50 mm Dia 60 Mtr 1281
46d 18.7.5 65 mm Dia 18 Mtr 1614
46e 18.7.6 80 mm Dia 165 Mtr 1885
46f 18.7.7 100 mm Dia 102 Mtr 2555
46g 18.7.8 150mm Dia 55 Mtr 3574
47 DSR (E&M)
2022
18.11 Supplying, fixing, testing and commissioning of butterfly
valve of PN 1.6 rating with bronze/gunmetal seat duly ISI
marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
47a 18.11.4 80mm Dia 2 E.a. 4980
47b 18.11.5 100mm Dia 5 E.a. 6667
48 DSR (E&M) Providing, fixing, testing & commissioning of 15mm dia
2018 quartzoid bulb type sprinklers of rating with required
21 accessories :
21.1 Pendent Sprinkler 68°C quick response UL Listed 240 No 400
49 R.A. 3 Set 5830
Providing fixing, testing and commissioning of Drainning
& Testing Assembly 25mm dia with Sight Glass , Union
joint , Ball Valve & Drain Valve.
50 R.A. Supply, installation, testing and commissioning of C.S. 4 No 41390
Foam water Monitor (1750 lpm) with aqua foam nozzle,
pick up tube, and required all accessories as per
specification
51 DSR (E&M)
2022 Providing, installation, testing and commissioning of
18.15 stainless steel Y-strainer fabricated out of 1.6 mm thick
stainless steel, Grade 304, sheet with 3 mm dia holes
with stainless steel flange.
18.15.3 150mm Dia 1 E.a. 11144
Automatic Fire Sprinkler System for Building.
52 DSR (E&M) Providing, laying, testing & commissioning of 'C' class
2022 heavy duty MS pipe conforming to IS 3589/IS 1239
18.7 including Welding, fittings like elbows, tees,
flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe
on the wall/ceiling with suitable clamp/support frame and
painting with two or more coats of synthetic enamel paint
of required shade complete as required :

52a 18.7.1 25 mm Dia. 415 Mtr 744

52b 18.7.3 40 mm Dia 81 Mtr 1034
52c 18.7.4 50 mm Dia 53 Mtr 1281
52d 18.7.5 65 mm Dia 28 Mtr 1614
53 DSR (E&M)
2022
18.11 Supplying, fixing, testing and commissioning of butterfly
valve of PN 1.6 rating with bronze/gunmetal seat duly ISI
marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
53a 18.11.2 50mm Dia 1 E.a. 3784
53b 18.11.3 65mm Dia 2 E.a. 4302
54 DSR (E&M) Supplying, installation, testing & commissioning of
2022 sprinkler flexible pipe (UL Listed) of stainless steel
18.25 complete with 15 NPT on reducer thread with maximum
working pressure of 175 PSI test pressure of 875 PSI
(Burst) with branch line (Inlet) 25mm NPT male thread to
sprinkler head (Outlet) 15mm NPT female thread with
reducer, nipple, 2 side brackets,center bracket, stockbar
of following sizes complete as required etc of following
sizes as required:

18.25.3 1200mm 140 Set 1670

55 DSR (E&M) Providing, fixing, testing & commissioning of 15mm dia
2018 quartzoid bulb type sprinklers of rating with required
21 accessories :
21.1 Pendent Sprinkler 57°C standard response (K-80) UL 225 No 400
Listed
Fire Extinguishers.
56 R.A. Supplying, Installation, Testing and commissioning of 8 No 3105
ABC type 6 Kg Fire Extinguisher Mono Ammonium
Phosphate Powder 50, Stored Pressure Type, Pressure
Gauge, Controllable discharge mechanism Class A,
Rating 3A & Class B rating 21B as per IS 15683 ISI
MARK (ABC Dry Chemical Powder - MAP 50%).

57 10-2-24. Providing & fixing of CO2 type Fire Extinguisher of 8 No 7700

capacity 4.5 kg filled with Co2 Gas as per IS 15222 with
controll discharge mechanis, fitted with Hose & Horn
applicable on Class B fire rating 21B confirms to IS 15683
bearing ISI mark. Co2 cylinder as per IS 7285

58 R.A. Providing & fixing of CO2 type Fire Extinguisher of 4 No 31265

capacity 22.5 kg filled with Co2 Gas as per IS 15222 with
controll discharge mechanism fitted with Hose, Horn &
TROLLEY confirms to IS 2878 bearing ISI mark. Co2
Cylinder as per IS 7285

59 R.A. Providing & fixing of Higher capacity Trolley mounted 4 No 34305

Mechanical Foam type Fire Extinguisher of Capacity 50
liter confirms to IS 13386, bearing ISI mark,
60 R.A. Providing & fixing of Mechanical Foam 9 Ltrs. Stored 2 No 3750
Pressure Type Controllable discharge mechanism
applicable on Class A & B Fire Rating 2A & 21 B

61 R.A. Supplying, Installation, Testing and commissioning of -

below Auto Glow Signages.
61a Fire Exit: 4" X 12" 9 Nos. 455
61b Fire Equipment: 4" X 12" 5 Nos. 455
61c In case of Fire, do not use lift, use staircase: 8" x 8" 3 Nos. 580
61d Fire Lift 4"X12" 3 Nos. 455
61e Fire Extinguishers 8"x 4" 10 Nos. 329
61f Floor Sign": 4" X 12" 3 Nos. 455
61g Fire Hydrant 4” X 12” 8 Nos. 455
61h Fire Hose Reel.4” X 12” 10 Nos. 455
61i DCP Extinguisher 8"x 4" 8 Nos. 329
61j CO2 Extinguisher 8"X 4" 8 Nos. 329
62 3-16-4 A Providing , erecting , fabricating the M.S. structure as per 1200 Kg 90
requirement on site incorporating proper size of M.S.
angles,square,round, flats, bars, channels, sections
complete with cutting, welding, grinding & finishing duly
painted with one coat of red oxide with erection on site as
per direction of engineer in charge with necessary
grouting, cementing, plastering & finishing complete.

63 R.A. APPROVAL FIRE SYSTEM FROM LOCAL FIRE 1 Job 125000

AUTHORITY
Getting Approval of Total Fire Fighting system from local
fire authority with all other charges and documentations
for getting No Objection Certificate.

64 R.A. Providing,fixing, testing and commissioning of 10Kg 4 No 3250

Modular type fire extinguisher having Nitrogen
expellant ,ceiling mounted,Sprinkler Nozzle is gas tight
the release temperature is adjusted with sprinkler
imported bulb set at 57 degree C or 68 degree
C ,coverage area 4 to 5 sqmtr,

Total Cost for Fire Fighting Work of Hanger Buildin

Say Total Cost for Fire Fighting Work of Hanger Buildi
1% Labour Rate with
Amount
Cess L.C.

4048.3 408878.3 817756.60

6169.66 623135.66 623135.66

1033.04 104337.04 104337.04
3102.3 313332.3 313332.30
6.23 629.23 37753.80

8.46 854.46 51267.60

4.59 463.59 20861.55

1.32 133.32 10665.60

0.43 43.43 347.44

0.54 54.54 436.32

1.63 164.63 329.26

0.28 28.28 56.56

0.52 52.52 315.12
 0.51 51.51 23179.50

0.36 36.36 16362.00

4.95 499.95 12498.75

7.25 732.25 14645.00

100.88 10188.88 10188.88

0.9 90.9 18180.00

0.9 90.9 909.00

12.6 1272.6 7635.60

 15.46 1561.46 6245.84

402.5 40652.5 40652.50

12936 1306536 1306536.00

984 99384 99384.00

2.1 212.1 509040

1154.34 116588.34 116588.34

7.01 708.01 708.01

73.69 7442.69 7442.69

9.75 984.75 11817.00

9.75 984.75 11817.00

8.5 858.5 10302.00

37.84 3821.84 7643.68

43.02 4345.02 4345.02
49.8 5029.8 5029.8
66.67 6733.67 13467.34
89.6 9049.6 45248.00
152.07 15359.07 92154.42
64.18 6482.18 6482.18
177.86 17963.86 53891.58
292.82 29574.82 29574.82

7.44 751.44 9017.28

12.81 1293.81 7762.86
16.14 1630.14 9780.84
18.85 1903.85 11423.10
25.55 2580.55 30966.60
35.74 3609.74 64975.32
54.63 5517.63 132423.12
66.59 6725.59 80707.08

222.65 22487.65 44975.30

763.93 77156.93 77156.93

4.11 415.11 4566.21

8.9 898.9 1797.80
29.97 3026.97 0

220 22220 22220.00

275 27775 27775.00
13.21 1334.21 10673.68
35.74 3609.74 613655.8
25.55 2580.55 361277.00
18.85 1903.85 38077.00

38.04 3842.04 69156.72

47.77 4824.77 632044.87
21.8 2201.8 0

49.8 5029.8 0
66.67 6733.67 13467.34
89.6 9049.6 27148.80

61.39 6200.39 49603.12

16.62 1678.62 16786.20

123.9 12513.9 150166.80

54.1 5464.1 65569.20

20.25 2045.25 4090.50

139.74 14113.74 14113.74

7.44 751.44 236703.6

10.34 1044.34 367607.68
12.81 1293.81 77628.6
16.14 1630.14 29342.52
18.85 1903.85 314135.25
25.55 2580.55 263216.10
35.74 3609.74 198535.7

49.8 5029.8 10059.6

66.67 6733.67 33668.35

4 404 96960.00
58.3 5888.3 17664.90

413.9 41803.9 167215.60

111.44 11255.44 11255.44

 7.44 751.44 311847.60
10.34 1044.34 84591.54
12.81 1293.81 68571.93
16.14 1630.14 45643.92

37.84 3821.84 3821.84

43.02 4345.02 8690.04

16.7 1686.7 236138.00

4 404 90900.00

31.05 3136.05 25088.40

77 7777 62216.00

312.65 31577.65 126310.60

343.05 34648.05 138592.20

 37.5 3787.5 7575.00

4.55 459.55 4135.95

4.55 459.55 2297.75
5.8 585.8 1757.40
4.55 459.55 1378.65
3.29 332.29 3322.90
4.55 459.55 1378.65
4.55 459.55 3676.40
4.55 459.55 4595.50
3.29 332.29 2658.32
3.29 332.29 2658.32
0.9 90.9 109080.00

1250 126250 126250.00

32.5 3282.5 13130.00

ng Work of Hanger Building in Rs. = 10364242.26

hting Work of Hanger Building in Rs. = 10364242.00
 ELECTRICAL POINTS SHEET OF HANGER BLDG at AM

Internal Electrical Wiring

Data &
Light and fan points voice UPS power

16A Plug point separate

secondary light point

computer Data point

Two way light point

Telephone point
6A P/P separate

6A P/P separate
wall light point

Exh fan point

6A P/P Loop

6A P/P Loop
Light point

Fan point
Sr.No Location

1 Basement Area
Store 1154sqft 2 2 2 4 4
2 2 2
2 2 2
2 2 2
2 2
Store-1 436 sqft 1 1 1 4 4
1 1
2 2 2
Store-2 436 sqft 2 2 2 4 4
2 2 2
Store Room 415sqft 1 1 1 4 4
1 1 1
1 1 1
1 1
Opp. Elect shaft 2 1
1
Dormatory-1 2 2 2 2 2
2 2 2
1 1 1
2.4Mtr wide passage 1 3
2.4Mtr wide passage 1 3 1 1
Dormatory-2 2 2 2 2 2
2 2 2
1 1 1
2.4Mtr wide passage 1 3
2.4Mtr wide passage 1 3 1 1
B/H Elect shaft 2 1
1
Store Room 436 sqft 2 2 2 4 4
2 2 2
Store 436sqft 1 1 1 4 4
1 1 1
 1 1 1
1 1
Store 415sqft 1 1 1 4 4
1 1 1
1 1 1
1 1
Fire Pump Room 2 6 4 2 2
2 6 4 2 2
1 3
Stairecase -1 1 1
Stairecase -2 1 1
Fire shaft 1 1
Fire shaft 1 1
2 SITE PLAN
Reception 2 2 1 1 1 2 2 2
2 2 2 2 1 2
1 2 2
Waiting Lounge 2 2 3 3
2 2
passage 232 sqft 2 2
Staff Area 211 sqft 2 4 2 6 6 6 6 6 6
1
Gent's Toilet 1 1 1 1
1 2
W/C 2 2 2
Pilot Room 1 2
2 2 3 1 3 1 1 1 1
W/C 1 1 1
Medical Room 1 1 1 3 3 1 1 1 1
passage entrance-1 LH 1 2
passage entrance-1 LH 1 1
2.4 Mtr wide passage LH 1 4
1 4
2.4 Mtr wide passage RH 1 3
1 3
passage entrance-1 RH 1 2
passage entrance-1 RH 1 1
Staff Area 830 sqft 3 3 3 6 8 6 6 6 6
1 2
3 3 3 6 10 6 6 6 6
1 2
QM 1 1 1 1 3 1 1 1 1
C.A.M. 1 1 1 1 3 1 1 1 1
A.M. 1 1 1 1 3 1 1 1 1
M.M. 1 1 1 1 3 1 1 1 1
Debriefing RM 1 1 1 1 1
Briefing RM 1 1 1 1 1
Workshop cum gr equipmnt 3 3 2 5 5
Pilot Room 3 4 1 3 1 1 1 1
Toilet 1 1 1
Pantry & dining area 3 3 2 3 1 1
Gent's Toilet 1 1 1 1
W/C 2 0
Ladies Toilet 1 1 1 1
W/C 2
Class Room 2 4 3 1 7 1 1 1 1
Class Room 2 4 3 1 7 1 1 1 1
COMM. Office 2 2 3 1 2 1 1 2 1
1 0 2
Toilet 1 1 1
Pantry 1 1 1 1 1 1
Meeting Room 3 7 4 1 7 1 1 1 1
Meeting Rm passage 1 1 1
Toilet passage 1 1
Toilet 1 1 1
CEO/CAI Cabin 3 7 2 8 3 1 1 1
Store 1 1 1 1
Library 2 2 1 2 2 2 2
P.H.Toilet passage 1 1
P.H..Toilet 1 1 1
Ladies Toilet 2 2
W/C 2 2 2
Security G.P.Air side entry-1 2 2 1
Lavatory 1 1
Security G.P.Air side entry-1 2 2 1
Lavatory 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Room 16' x 5' 2 2 1 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Space for workshop /others 3 3 2 1 1 1 1 1 1
Room 16' x 5' 2 2 1 1 1 1 1 1 1
Fire shaft 1 1
Fire shaft 1 1
Stairecase -1 1 1
Stairecase -2 1 1
3 FIRST FLOOR
Staff Area 3 3 2 4 6 4 4 4 4
Exe.Engr-2 3 3 2 3 1 1 1 1 1
Exe.Engr-1 5 3 2 1 4 1 1 1 1
conference Hall 4 8 4 1 9 1 1 1 1
1 5
2 6
Rest Room 4 3 2 1 4 1 1 1 1
Toilet 1 1 1 1 1
Ladies Toilet 2 2
2 2 2
Pilot cabin-1 3 3 2 1 3 1 1 1 1
Pilot cabin-2 3 3 2 1 3 1 1 1 1
Gent's Toilet
Gent's Toilet 1 1 1 1
1 2
W/C 2 2 2
2.4 Mtr wide passage 3 9
Stairecase -1 1 1
Stairecase -2 1 1
Fire shaft-1 1 1
Fire shaft-2 1 1
4 Terrace
Stair cabin-1 1 1 3
Stair cabin-2 1 1 3

Total 223 34 263 123 16 6 106 174 3 59 56 62 59

wall light points 34 ups 59 62
16 Exh.fan

TOTAL 257 34 263 123 16 6 165 252 3 59 56 62 59

 1
1
LED Lamp

2
2
4
4
1
4
4
4
4
1
1
2
2
2
4
4
4
2
2
4
4
4
4
4
Recess/surface 20/24 w LED

2
4
4
2
4
4
2
2
Recessed/ surface 10/15w
HANGER BLDG at AMRELI

15w COB LED

Step light

Mirror light 10w LED

Light fixtures

spot light 7w

spot light 11w

120w Flood

200w Highbay

cassette

1.5TR
HVAC

2.0TR

1 TR
 2
1
2
2
2
1
8
8
4
2
2
1
1

2 2 1
2 2 1
1
2 2 1
2 2 1
2 2
6 1

0 2 1
3
2 2
3
4 1
0 1 1
2 1
3
2
5
5
4
4
3
2
6 2
3
6 2
3
2 1
2 1
2 1
2 1
 2
2
6
4 3 1
1
6
1 0 1
2
1 0 1
2
6 2
6 2
4 1
3
1 1
2
8 2 4
1 2
1 1
1 1
8 2 4
2 1
4 1
1 1
1 1
1 3
2 2
4
2
4
2
6
6
6
6
4
6
6
6
6
4

2
2
 6 1
6 1
6 1
12 4
6
8
3 4 1
2 1
1 3
2 2
6 1
6 1

2
3
2 2
12
2
2

2 3
2 3

20 331 128 16 6 9 8 4 18 13 6

20 331 128 16 6 9 8 4 18 13 6
 LOAD SHEET OF HANGER BLDG,AMRELI

Sr.No Description Qty Watts/no Total watts

A
1 24w LED Fixtures 331 28 9268
2 15w LED Fixtures 128 18 2304
3 9w Mirror Light 9 11 99
4 15w COB 16 18 288
5 7w Spot light 8 9 72
6 150W Highbay Fixtures 40 160 6400
7 HVAC
a 2 TR cassette A/C 4 2400 9600
b 2 TR Split A/C 13 2400 31200
c 1.5 TR Split A/C 18 1800 32400
d 1 TR Split A/C 6 1200 7200
8 Ceiling Fan 123 55 6765
9 Exhaust Fan 16 200 3200
10 CCTV & PA System 1 1000 1000
11 Domestic Pumps 2 2250 4500
12 Fire Fighting System
a Foam System pump 1 30000 30000
b Hydrant & Sprinklers pump 1 30000 30000
c Jockey Pump 1 7500 7500
13 Passengers Elevator 2 10000 20000
14 Borewell 1 12500 12500

Total connected Load 214296

Load Factor 0.8 171436.8
Say 171 Kw
B
1 6A Plug points Separate 174 150 26100
2 16A Plug points 3 400 1200
3 Receptecals in hanger shed 1 12000 12000
4 Data Points 60 300 18000
Total connected Load 57300
Load Factor 0.8 45840
SAY 46 Kw

TOTAL of A + B KWs 217

Diversity Factor 0.65 141.05

Actual Demand 142 KW

Total connected Load 271596
Load Ampere 407394
Size of incomer ( 2 x load ampere) 814788
Required 800A FP ACB

Compact Substation 315 KVA

Load capacity in KW(315x0.8) 252 KW
Safe Loading of CSS ( 80% ) 201.6 KW

Demand Load of project 142 KW

Spare capacity 59.6 KW
 Qty
1 Main L.T.Panel 1 no.
Incomer 800A FP ACB E.D.O.

Outgoings
1 Fire Fighting system 250A FPMCCB
2 HVAC Panel 250A FPMCCB
3 Spare 250A FPMCCB
4 APFCR Panel 160A TPMCCB
5 Lighting Distribution Board 160A FPMCCB
6 Hanger Receptacles 160A FPMCCB
7 Spare 160A FPMCCB
8 UPS 30KVA 125A FPMCCB
9 LIFT-1 63A FPMCB
10 LIFT-2 63A FPMCB
11 Domestic Pump room 63A FPMCB
12 Spare 63A FPMCB
13 Spare 63A FPMCB
14 Spare 40A DPMCB
15 Spare 40A DPMCB

2 UPS Panel 1 no.

Incomer 125A FPMCCB

Outgoings
G.F. UPS DB-1 63A FPMCB
G.F. UPS DB-2 63A FPMCB
F.F. UPS DB-3 63A FPMCB
Spare 63A FPMCB
Hanger shed UPS DB-4 40A DPMCB

3 60KVAR APFCR Panel 1 no.

4 Street Light control Panel 1 No

 CABLES & CABLE GLAND

Aluminium armoured

3.5c x 150sqmm

3.5c x 120sqmm

3.5c x 95sqmm

3.5c x 50sqmm

4c x 25sqmm

4c x 16sqmm

4c x 10sqmm
From To

Transformer ATS 800A 30

D.G.Set ATS 800A 30
ATS 800A Main L.T.Panel incomer 210
Main L.T.Panel Fire Fighting Panel 60
Main L.T.Panel HVAC 6way VTPN DB 50
Main L.T.Panel APFCR Panel 20
Main L.T.Panel Lighting Dist.Board 6 way VTPN DB 95
Main L.T.Panel Hanger receptacles 8way VTPN DB 80
Main L.T.Panel UPS Panel 60
Main L.T.Panel HVLS 8 way VTPN DB
Main L.T.Panel Lift-1 power D.B.
Main L.T.Panel Lift-2 power D.B.
Main L.T.Panel Domestic pump D.B. 4 way TPN 60
Main L.T.Panel Borewell 150
Fire Panel Foam Pump
Hydrant Pump
Jockey Pump
D.G.Set driven pump
HVAC 6way VTPN DB G.F. ACDB-1
G.F. ACDB-2
G.F. ACDB-3
F.F. ACDB-4
Reception + waiting 3TR Cassette
Reception + waiting 3TR cassette-1
Cassette
cassette-2
cassette-3
cassette-4
Lighting Dist.Board 6 way
VTPN DB Basement L.D.B.-1 70

Basement L.D.B.-2 70
Shed Area L.D.B.-3 60
Shed Area L.D.B.-4 60
G.F. L.D.B.-5 80
G.F. L.D.B.-6 80
 F.F. L.D.B.-7 100
UPS Panel G.F. UPS DB-1
G.F. UPS DB-2
F.F. UPS DB-3
Hanger shed UPS DB-4
Hanger shed UPS DB-5

Domestic pump D.B. 4 way

TPN Pump starters

Hanger receptacles 8way Industrial power point-1

VTPN DB
Industrial power point-2
Industrial power point-3
Industrial power point-4
Industrial power point-5
Industrial power point-6
UPS INPUT
UPS Output
HVLS 8way VTPN DB HVLS Fan 1 to 8

270 60 70 235 150 580 0

 3C X 16SQMM

30
30
4c x 10sqmm

55
45
25
70
95
80

125
3c x 6sqmm

45
4c x 6sqmm
ES & CABLE GLANDS DETAILS

CU Armoured

4c x 4sqmm

20
20
20
20
4c x 2.5sqmm

95
30

125
7c x 1.5sqmm

80
1 x 25sqmm
CU WIRE

4
4
4

3.5c x 150sqmm
2

3.5c x 120sqmm
2
2

3.5c x 95sqmm
2
2
2

3.5c x 50sqmm

2 4c x 25sqmm

2
2
2
2
2
2
4
4
4
2

4c x 16sqmm

2
2
2
2
3
3
2
CABLE GLANDS

4c x 10sqmm

4c x 6sqmm
 2
80 2
50 2
110 2
115 2
115 2

20

270
2
2
2
2
2
2
40
40
390

60 965 45 270 100 640 80 80 12 2 4 6 2 28 26 12

 DS

2
2
2
2
4c x 4sqmm

2
4c x 2.5sqmm
6

16

14 18
 MCBDBs and MCBs Details

160A FP MCCB
6way VTPN DB

250A FPMCCB

125A FPMCCB

100A FPMCCB

6-32A FPMCB
8 way VTPN

63A FPMCB

40A FPMCB
12 way TPN

8 way SPN
4 way TPN

8 way TPN
HVAC 1 1
G.F. ACDB-1 1 1
G.F. ACDB-2 1 1
G.F. ACDB-3 1 1
F.F. ACDB-4 1 1
Lighting Dist Board 1 1
Basement L.D.B.-1 1 1
Basement L.D.B.-2 1 1
Shed Area L.D.B.-3 1 1
Shed Area L.D.B.-4 1 1
G.F. L.D.B.-5 1 1
G.F. L.D.B.-6 1 1
F.F. L.D.B.-7 1 1
G.F. UPS DB-1 1 1
G.F. UPS DB-2 1 1
F.F. UPS DB-3 1 1
Hanger shed UPS DB-4 1
Hanger shed UPS DB-5 1
Domestic Pumps 1 1 3
Lift -1 power 1 1
Lift-2 power 1 1
Lift-1 Light
Lift-2 Light
Hanger Receptacles 1 1
UPS Main supply 1
HVLS Fans 1 1 8

2 2 1 5 9 4 1 1 1 1 18 11
 8
5
6
63A TPMCB

19
6-32A TPMCB

1
1

2
40A DPMCB

6-32A DPMCB

10
10
10
10

40
1
1

2
40A FP RCCB

3
3
3
3
3
3
3
3
3
3
63A DP RCCB

30
1
1

2
40A DP RCCB

1
1

2
25A DP RCCB

4
4
6-32A SPMCB

18
18
18
30
30
30
30
30
30
30

272
 H.T. and D.G.Set Earthings Details
3 Mtr 3 Mtr CU AL GI
80mm dia 50mm dia 50 x 6 25 x 3 50 x 6 50 x 6 25 x 6
HT-Switch 2 20
CSS
RMU 1 10
Transformer body 2 30
Transformer Neutral 2 25
D.G.Set
Body 2 30
Neutral 2 30
ATS 1 20

4 8 55 90 20

KG/Mtr 3.044 0.866 2.5

167.42 77.94 50

General Electrical work Earthings Details

Main L.T.Panel 1 40
L.T.Panel Room 35
UPS 30KVA 1 40
UPS MCBDBs
HVAC VTPN DB
Lighting MCBDBs
Hanger Receptackles DB 1 80
All Receptacles
LIFT-1 1 40
LIFT-2 1 40
2 3 0 40 40 115 80

KG/Mtr 3.044 0.75 0.866 2.5 1.25

WEIGHT 0 30 34.64 287.5 100

FIRE ROOM Earthing Details

Fire Panel 1 50
Domestic pumps MCBDB 25
Foam-Pump 20
Hydrant Pump 5
Jockey pump 5
Diesel Driven Pump

1 50 55

KG/Mtr 3.044 0.866 2.5 1.25

WEIGHT 0 0 125 68.75
GI GI Wire
25 x 3 8SWG

150
80
500

160

390 500

0.65 0.103
253.5 51.5

20
20
 20
20

80

0.65 0.103
0 8.24
LIGHTNING ARRESTOR DETAILS

10mm dia al
Air terminal

14.2mm dia
8mm dia al
conductor

conductor

earth rod
25x6mm
G.I.Flat
Items

S.O.R.No 10-5-1. 10-5-2.

Unit No Mtr Mtr Mtr No
Sr.No Location
1 O/H Tank-1 upper Terrace 2 15 20 50 2
2 O/H Tank-2 upper Terrace 2 15 20 50 2

4 30 40 100 4
 WIRING MAINS DETAILS

4c x 2.5sqmm round

4c x 1.5sqmm round

3c x 1.5sqmm round
2 x 1.5sqmm

2 x 2.5sqmm

2 x 4 sqmm
HVAC
G.F. ACDB-1 300 30
G.F. ACDB-2 270
G.F. ACDB-3 320 120
F.F. ACDB-4 140 140
760 560
Lighting Dist Board
Basement L.D.B.-1 360 700
Basement L.D.B.-2 360 700
Shed Area L.D.B.-3 240 160
Shed Area L.D.B.-4 240 160
G.F. L.D.B.-5 450 800
G.F. L.D.B.-6 450 800
F.F. L.D.B.-7 360 700

UPS
G.F. UPS DB-1 210 160
G.F. UPS DB-2 320 210
F.F. UPS DB-3 250 125
1980 3700 1260 320 495