-40°C UPRIGHT FREEZER UPQ 3006 OPERATION MANUAL www.laboquest.com [email protected]i Nn a PS a a . Introduction = . Installation er elmer ee) el) ECT LS GL . Product Diagram and Overview—————————————————— PO ENMU Mal aero e MC Ces Ce) PTS UTS Ts ROM Uy Ce et: . Trouble Shooting ———————————— ——_—_—_—_—_—_—_—_—__— a eda iC ML: oe1. Introduction Thank you for choosing our upright freezer. Read this manual carefully before using the appliance and follow the instructions for the safety operation. Keep this manual in an adequate place to refer to it as necessary. Manufacturer never guarantee any safety if the appliance is used for any objects other than intended use or used by any procedures other than those mentioned in this manual. The contents of the manual will be subjected to change without notice due to the improvement of performance or functions. Contact Manufacturer sales representative or agent if any point in this manual is unclear or if there are any inaccuracies. No part of this manual may be reproduced in any form without the expressed written permission of Manufacturer. + Please read the page4-page7 carefilly as it contains the important safety notices. «Only trained or authorized personnel could operate this Ultra-low temperature freezer. + Only qualified service personnel or authorized agent could install and maintenance this device + Use Manufacturer spare parts as always. If users want to use other accessories, Manufacturer will not be responsible for the adverse consequences. However users could apply for verifying the eligibility of these accessories from before use them. + Should inspect and maintenance the device in a specified time interval. + Due to the differences between each model and the improvements of products, actual product may differ from the diagram. Please refer to the final product. + Everyone has an obligation to be responsible for his or her own safety. «Put on dry gloves when you take out refrigerated articles from the freezer. + Contents or the inside walls with naked hands may cause frostbit. Handing Frozen MR crete tert str mat terertitics eye After each item is accessed, be sure to dry the water stains around the inner door frame and seal to prevent freezing. Pr Friendly reminder © Always use protective equipment (including clothing, gloves, goggles, etc.) correctly. © Always adopt good hygiene. © Everyone is responsible for his/her own safety.2. Precautions for Safe Operation For the first time to use this device, uses must read the meaning of the following warning labels very carefully. Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the user and any other person. WARNING. Failure to observe WARNING signs could result in a hazard To personnel possibly resulting in serious injury or death CAUTION. Failure to observe WARNING signs could result in ‘injury to Personnel and damage tothe unit and associated Propet A CAUTION HOT. A The sign inform the users about the danger of burns for e DANGER OF EXPLOSION. ‘The sign inform the danger of the application of volatile, explosive chemical substances. high temperature. ® NO TILTING. STAY OUT OF SUN. BEWARE OF ELECTRIC SHOCK! Dangerous voltage may cause personal injury! Please ssconncet the power supply betore rept (Ss NO TRAMPLING EQUIPMENT. DEY NoTUMB HB oPackaces. (G TRANSPORT Yy PRECISION INSTRUMENTS. © neces ‘THE CONTENTS MUST BE PLACED AT THE ARROW. I - FEAR OF THE RAI EE nostackine. HYSRG No cLampine. WARNING A Failure to observe WARNING signs could result in a hazard to personnel possibly resulting in serious injury or death As with any equipment that uses CO2 gas, there is a likelihood of oxygen depletion in the vicinity of the equipment. Itis important that you assess the work site to ensure there is suitable and sufficient ventilation. Ifrestricted ventilation is suspected, then other methods of ensuring a safe environment must be considered. These may include atmosphere monitoring and warning devices cause electric shock. Do not touch any electrical parts such as the power supply plug or any switches with a wet hand. This may Only qualified engineers or service personnel should install the unit. The installation by unqualified personnel may cause electric shock or fire.‘Be sure to install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not adequate, this may result in injury from the unit falling or tipping over. Carefully with the power cord to avoid short circuit or open circuit. When removing the plug from the power supply outlet, grip the power supply plug, not the cord, Pulling the cord may result in clectric shock oF fire by short circuit. Don't make the power line pack and pressed by furnish or heavy goods. Also please don't close to the compressor and heat source. Please insert the power plug firmly to avoid leakage. Use a power supply outlet with ground (earth) to prevent electric shock, If the power supply outlet is not ‘grounded, it will be necessary to install a ground by qualified engineers. Don't lengthen the line randomly. If you need, To use 2.Smm2 copper line, you should keep 4mm2 line to connect the electrical outlet. Or may cause fire. > PP PRP Pe Make sure a dedicated power source is used as indicated on the rating label attached to the unit. Out of the rate, should install a property transformer and a proper voltage stabilizer for securely operation. Or the freezer may be damaged, and may cause injury. ‘Be sure to install the unit on a sturdy floor, no shaking and tilting, ‘Never install the unit ina flammable or volatile location. This may cause explosion or fire. ‘Never install the unit in a humid place or outdoor or a place where it i likely to be basked straightly. Deterioration of the insulation may result which could cause current leakage or electric shock. ‘Do not place the device lateral tilt, do not impact the device; the device is equipped with refrigeration systems, roll or shock will easily damage the freezer. Be sure to install the device in a dry dust-free environment to avoid overheating, short circuit and other dangers. PPP eer © there is an unexpected sound, smell, smoke when the power is tumed on, unplug the power and contact the manufacturer or supplier. Continued abnormal operation may cause electric shock or fire.Make sure a dedicated power source is used as indicated on the rating label attached to the unit. Out of the rate, should install a property transformer and a proper voltage stabilizer for securely operation. Or the freezer may be damaged, and may cause injury. Make sure to put the freezer in a dry and ventilated environment, to ensure that equipment vents and wall surface of the instrument or other items have not been blocked; Do not use the device in a poorly ventilated environment, or the equipment may be damaged by the release of heat Never disassemble, repair, ot modify the unit yourself. Any such work carried out by an unauthorized person may result in fire or injury due to a malfunction, Laboquest will be no responsible for such work. Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use may cause bad effect on your health or environment, Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such groundi may cause electric shock in the case of an incomplete circuit © PBPP BP Pe Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is not ‘grounded, it will be necessary to install a ground by qualified engineers. CAUTION Failure to observe WARNING signs could result in injury to personnel and damage to the unit and associated property Ultra-low temperature freezer is not available to store living things, flowers, or other critical articles which is not suitable for low temperature storage. ‘The temperature inside the freezer is very low during the normal working. Do not touch the interior surface of the chamber or the object inside without wearing protective gear. Always disconnect the power plug when the unit is not used for long periods. Make sure to prepare a safety check sheet when you request any repair or maintenance for the safety of service personnel. Be sure to check set point of the controller prior to restart the freezer. ‘The ultra-low temperature freezer is a storage device, not a production equipment! Always hold the handle when closing the door. This will reduce the likelihood of a trapped finger. Keep the key properly avoiding the children take itto open the door which may result in unexpected injury.Select a level and sturdy floor for installation. This precaution will prevent the unit fom tipping. Improper installation may result in water spillage or injury from the unit tipping over. Check the filter mentioned in this manual and clean it as necessary. A dusty filter may cause temperature rise or failure. Do not tilt the unit more than 45 degrees when moving the unit. All transportation should be carefully. Air Rd When the freezer is running, the front part of the freezer may get hot. This is not a malfunction: In order to prevent dew condensation around the case body, a heated anti-condensation tube is installed in the cryogenic storage case Before putting the items in the freezer, please make sure the temperature inside the box has reached the set temperature, and then put the items in batches. Add no more than 1/3 of the container volume each time, in case the temperature rises too much. The temperature display value shows the temperature of temperature sensors inside the freezer. Although the displayed temperature may sometimes differ from the actual temperature in the centre of the freezer, it will get close to the real temperature gradually. A through-hole is installed on the right or back of the freezer to allow test lines to exit the test box. After drawing out the test lines, be sure to re-plug the test hole with insulating material, otherwise the temperature inside the box will not be completely lowered, resulting in condensation around the outside of the hole. Clean the freezer with diluted neutral detergent. Do not use brushes, acid, gasoline, soap, polish or hot water to clean the frozen storage container, as these materials may damage the painted surfaces and plastic rubber components. After a period of operation, a layer of frost will form on the inner wall and the inner door. If the frost layer is too thick, it will affect the insulation effect of the freezer and increase the power consumption, Therefore, after a period of time, when the frost layer reaches about Smm, it should be defrosted with the deffost shovel attached. Please remove the frozen items in the freezer and put them in a suitable storage environment before defrost, so as to avoid the damage of goods for temperature rise. There are many cooling coils on the back and side of the inner wall. Don't use sharp objects such as knives, ice chisel, or screwdrivers to remove the frost on the inner wall. Be careful not to scratch the inner wall when defrosting, otherwise it will cause a failure of the freezer. Cut off the power when the refrigerated storage box will not be used for a long time.CCL) 4. 1 Installation environment Ambient temperature: 16°C~32°C, optimal ambient temperature:18°C ~25°C, air condi system is required if necessary. Relative humidity: <80%RH. No strong vibration and no corrosive gases around. Without the presence of a lot of dust No shaking or vibrating of the freezer. Altitude of the place where the freezer is located : <2000m Indoor use, pollution degree 2 level, overvoltage category I Input voltage AC single phase 220V422V No direct sunlight or any other cooling or heating source, no electromagnetic interference, or the freezer will not run properly Keep the distance between the freezer and the surrounding wall of 30 cm or more, and the air outlet must not be obstructed, pay attention to room ventilation or opening air conditioner during the hot summer. 0 CAUTION. Since the ambient temperature has a great impact on the operation of the freezer. If the freezer is installed in the other situations instead of above conditions, the freezer will not run properly. 4.2 Installation site : This unit is a precision machine. When select a location to install this unit, keep the following conditions for perfect performance: ‘* Should not be installed in a small confined space, the door of the room should not be less than height of the present equipment. Install the unit on a sturdy floor to avoid excessive vibration and noise. Installing the unit in direct sunlight may cause malfunctioning and may shorten the life of the unit, Keep good ventilation is necessary. Do not share a socket with other equipment, plug and socket should be securely connected Socket inputs should be connected to circuit protection facilities, such as: An air switch which the rated current is bigger than 45A. If an extension cord is needed, be sure to use copper wire more than 2.5mm”. The cross-sectional area of the copper wire inside the wall connected with the power outlet must also be more than 4mm’, Checking the working voltage of the place before start the freezer. A voltage stabilizer is suggested to be used at the place where the voltage is not stable. Make sure the normal input voltage stable at 115V + 10% or 208V+ 10%, Power of voltage stabilizer should be more than 4KW. Be sure to ground the unit. Grounding prevents electric shock which occurs when the electrical insulation of the unit becomes insufficient.a WARNING Make sure of using a plug with earth provision and to ground the unit to prevent the electric shock in the event of the current leakage. Substituting a water pipe for the ground terminal will not provide proper grounding in many instances since plastic pipes are often used for water piping Never ground the unit through a bas pipe, as it is very dangerous. Never ground the unit through the telephone line or lightning rod, as large currents flow if lightning strikes, making it very dangerous. 4.3 Preparation before use © Please read this manual carefully when using this machine for the first time. © Ultra-low temperature storage and handling: lifting should be done from the bottom and the inclined plane should not be more than 45 degrees. Remove all packaging components (including protective foam in the case) Please check the random attachments and materials according to the packing list The product should be cleaned before use. Adjust the non-slip support feet: use a wrench to rotate the fixed feet clockwise to extend ‘outwards to support them on the ground. Make sure the device does not move while in use. A WARNING Do not place the packaging plastic bag in a place where children can reach it to prevent suffocation. 4.4 First use When using the device for the first time, please follow the steps below: 1. After the equipment is levelled and cleaned, it needs to stand for more than 24 hours, and then turn on the power to ensure the normal operation of the equipment, 2.Under no-load conditions, connect the power cord to a dedicated socket of appropriate specifications. 3. After tuning on the power, turn on the power switch of the device (if the auxiliary cooling system is installed, turn off the switch first). 4, Set the required temperature in the cabinet 5.If you hear the alarm sound when you power on for the first time, you can touch the mute button to eliminate the alarm sound. 6.Check whether the operating temperature of the equipment reaches the required temperature, observe that the equipment is normally started and stopped for more than 24 hours, and after confirming that the performance is normal, you can place a small amount of items in the storage room. 7. Please store the items in batches, each time not exceeding 1/3 of the box volume. Ensure that the equipment is shut down, and that it has been normally opened and stopped for more than 12 hours before placing the next batch of items). 8. Try not to open the door during the cooling process; otherwise it will cause the temperature to rise. 9. If the auxiliary cooling system is installed, open its device.4.5 Operation after power off 1.The device has a memory function for the set value. When the power is restored after the power is tumed off, the device will continue the operation before the power is tumed off. 2.Once the power supply of the equipment is interrupted during use, it can be tumed on again after waiting for $ minutes to avoid damage to the compressor. 3.Our company guarantees the normal operation of this equipment under certain conditions, but is not responsible for any loss or damage to the items stored in the machine after power failure. oe Attention please! > The transportation of equipment is realized by casters. > The equipment should be in charge of a special person, check the operation status and record every day (record and check every 2 to 4 hours). The temperature of the storage room will rise in case of failure or shutdown. If it cannot be repaired within a short period of time, please remove the stored items and transfer them to a place that meets their temperature requirements for storage to avoid damage to the items Before putting items into the device, you should confirm in advance whether the temperature range of the device meets the required temperature of the item, to avoid the inconsistency between the settable temperature of the device and the required temperature of the item, resulting in damage to the stored items. Block the air outlet and air intake. Due to cooling inertia, there is a certain difference between the actual display temperature and the set temperature, which is normal The equipment is an item storage device and cannot be used for routine production operations. It is strictly forbidden to put too many relatively hot items at one time, otherwise it will cause the compressor to run for a long time and the temperature will be too high to burn, The items must be placed in batches to ensure that the storage room cools down in steps until it reaches the temperature required for item storage. Do not use electrical appliances without production permission inside the equipment. The power supply voltage fluctuates or alarms for a short time during use. If the voltage range is between 198V and 242V, it will not affect the normal use of the storage box. Do not change the set temperature frequently within a short period of time. Otherwise, due to the large inertia of hot and cold, the expected adjustment effect may not be achieved; when placing items, ensure that there is a certain air circulation space around the box, especially do not block it ‘Temperature sensor in the box (for collecting the temperature of the box), otherwise it will affect the stable and accurate control of the temperature in the box! When putting items, if the items are too watery or too dry, it will affect the change of humidity in the box. The items should be sealed and stored; the humidity of the working environment will affect the change of humidity in the box, especially if the door is opened too much and the door is not closed properly. A WARNING Children are not allowed to play with this device as game props, otherwise the injury or loss caused will be at your own risk5. Product Diagram and Overview 40" FREEZER Due to the improvement of the product and different models, the actual product may be different from the diagram, please take the actual product as the standard! The schematic diagram is only used for function description. Structure and composition: the product is composed of Cabinet, door body (glass door structure or foam door structure), reftigeration system and control system. + Scope of application: it is suitable for storing articles in hospitals, pharmacies, epidemic prevention stations, research institutions, biological pharmaceuticals and other units.6.1 Function introduction 1 2 3 4 5 6.1 The functions represented by each indicator light: (as shown in the table on the right) eon) Serial port | Key lock | Defrosting | Power supply oeo00 Dump energy | Power off | Mute Door switch a. Serial port indicator light When the freezer is not connected to the reserved RS-485 serial port, the serial port indicator light is off; when the freezer is successfully connected to the reserved RS-485 serial port, the serial port indicator light is on b. Key lock indicator light When the keys are in the locked status, the keys will not respond, and the key lock light will be on. At this time, press and hold the up key + down key for 3 seconds, it will prompt to input the password, the default password is “00S”. After inputting the password correctly, press the setting/mute key, the key lock will be disabled and the key lock indicator light will be off. If no key is pressed for 60s in the unlocked status, the key lock will be enabled, and the key lock indicator light is on. Press and hold the up key + down key for 3s, the keys will be locked. c. Reffigeration indicator light If the compressor is in the operation status, the refrigeration indicator light will always be on; if the compressor is in the shutdown status, the reftigeration indicator light will be off. d. Power supply indicator light When the indicator light is on, it indicates that the product power supply is enabled. e. Low battery indicator light When the battery voltage is lower than 10.8V, the buzzer will sound, the low battery indicator light will be on, and the Nixie tube will blinking display the low battery code “PL” alternately at a 3s interval; when the battery voltage is greater than 12V, the buzzer will become mute, the low battery indicator light be off and the Nixie tube resume normal display. f Power failure indicator light The freezer is normally powered at a voltage of 220V. When the input power is disconnected, the buzzer will sound, the Nixie tube will blinking display the power failure code “Pf” alternately at a 3s interval and the power failure indicator light be on. When the input power is connected, it will resume normal and the power failure indicator light become off.g. Mute indicator light When the alarm tone key is muted, the indicator light will be on; when the alarm tone mute function is disabled, the indicator light will be off. h. Door switch indicator light When the door is open, the door switch indicator light will be on; when the door is closed, the door switch indicator light will be off. 2. EEMBHis the temperature display window, used to display the average internal temperature inside the freezer under normal operating conditions, in the unit of °C; Ambient temperature view: When the keys are locked, press the @ key, the Nixie tube will display the ambient temperature. It will resume normal display if no key is pressed for 5 seconds or by pressing @ and @ When the keys are unlocked, press the € key, the Nixie tube will display the ambient temperature. It will resume normal display if no key is pressed for S seconds. Humidity view: When the keys are unlocked, press and hold & key and @ key, the Nixie tube will display the humidity. It will resume normal display if no key is pressed for 5 seconds or by pressing Banda 3. Bis the up key; in the parameter setting mode, press it to move to the next parameter or increase the parameter value. For example, when setting the temperature, it may be used to increase the set temperature value. When setting the parameter value, press and hold the up key to increase the parameter value quickly. Under normal conditions, press and hold the up key for 3s to import the data of 12 months into the USB flash disk. 4. is the down key; In parameter setting mode, it may be used to move to the previous parameter or decrease the parameter value. For example, when setting the temperature, it may be used to decrease the set temperature value. When setting the parameter value, press and hold the down key to decrease the parameter value quickly. 5. Bis the setting/mute key. When there is no alarm and the keys are not unlocked, press ® it will display the ambient temperature, and will resume normal display after 5s; in the unlocked status, press © for more than 3s to enter the user menu. When the buzzer sounds (including cabinet over temperature alarm, door open alarm, sensor fault alarm, etc.), and the keys are not unlocked, press ®@ for the first time, the buzzer will stop sound, and it will display the ambient temperature and resume normal display after 5s (only the buzzer for this abnormal status alarm is turned off by pressing the mute key, although the fault is eliminated, the buzzer will also sound if it becomes abnormal again). Press @- again, the buzzer will sound, it will display the ambient temperature and resume display of cabinet temperature and alarm status after 5s. When the keys are unlocked, . can be used as the setting key. When the keys are unlocked, in the parameter setting mode, press this key to display the parameter value and parameter name. Press and hold it for more than 3s, it will save the setting and return to the normal interface. 6. USB data export (optional); Automatic export: When the USB flash disk is connected to the USB interface, the recorder buzzer will sound once, the Nixie tube display “on”, and the PDF file of the current month and the previous month will be generated in the USB flash disk. After the data transmission is completed, the buzzer will sound once, and the Nixie tube display “End”, and resume normal display after 6s. Note: When there is little data, the Nixie tube will not display "on" or "End"‘Manual export: When the keys are not locked, the USB flash disk is properly connected, and the file has not been generated yet, press and hold the up key for 3s, the Nixie tube will display “d01”, press the up key or the down key to adjust it to “d00~d12”, press @ key, the file generated this time (400) or the file for the previous month (1-12) will be saved in the USB flash disk in the format of PDF. Note: When the Nixie tube blinking displays “LoF”, the recorder has not been started yet; press @ the and &§ keys for 3s, “LoF” will disappear, the buzzer sound once, and the recorder will be started. 6.2 Function settings a. Connect the power supply and turn on the power switch on the back of the cabinet, the ‘machine will be in the working status; b. User parameter settings: Unlock: In normal operation, press and hold the @ and @ keys at the same time for 3s, the Nixie tube will display the parameter code “000”, enter the password “005” (when entering the user menu password, enter “099” to restore the key lock password to the default “005”,) to unlock. After unlocking, press and hold f for 3s, the Nixie tube will display the parameter code “PSI” and it enter the settings to adjust the parameters. Use the @ or @ key to roll the parameters. The display order is Psl bl +b2—Set-H+L ny 1S +F Pt AHL, Press @ to confirm the parameter category, the first parameter name of each category will be displayed; ® Use the @ or @ key to roll the parameters; ® Press the & key to display the corresponding parameter value; @ Use @ or @ to increase or decrease the value; @ Press © to temporarily store the modified value and return to the display parameters; ©) If you want to modify other parameters, repeat steps D~@ © Press and hold @ for more than 3s to store the modified parameters and return to the display parameter category. c. Exit the parameter setting program by pressing and holding ®P. for more than 3s, or after no key isHardware version Software version ‘Temperature setting High temperature alarm set value sett H"; when H=0, cancel the alarm, when the temperature is too high, the high temperature alarm shows Hi Low temperature alarm set value "set-L"; when L=0, cancel the alarm, when the temperature is too low, the low temperature alarm shows L1 Print interval Ambient temperature alarm upper 20.0-50.0°C limit 0000-9999 User menu password setting 6.4 Alarm display Alarm code Fault description HI High temy alarm. Li Low temperature alarm High ambient temperature alarm High condenser temperature alarm Door ajar alarm: Power failure alarm Low battery alarm Recorder not connected (if any) Recorder not activated (if any) Communication fault ae@ Note: the “high temperature alarm" is a normal phenomenon when starting the machine for the first time, After the temperature in the cabinet is stable, the "high temperature alarm" will be automatically removed before putting in the goods. Note: the storage of goods should not exceed 1/3 of the cabinet capacity each time. After reaching the set temperature and running normally for 24 hours, the goods with another 1/3 of the cabinet capacity should be put into storage. Try not to open the door during the cooling process, or the temperature will rise Note: do not set the temperature frequently in a short period of time, otherwise, due to the large inertia of hot and cold, it may not reach your expected setting effect;When placing items in the cabinet, ensure that there is a certain air circulation flow space around the cabinet, especially keep off the temperature sensor hole inside the cabinet (for collecting the temperature inside the cabinet), otherwise it will affect the stability and accurate display control of the temperature inside the cabinet! Note: do not cover the temperature sensor hole in the cabinet (use it to collect the temperature in the cabinet) for items placed in the cabinet or it will affect the stability and accurate display control of the temperature in the cabinet! 6.5 Optional Accessories 6.5.1 Printer The printer has a roll paper installed at the factory, but when used for a long time, when it is used up, you can buy the same roll paper (size: thermal paper, paper width 57.5 + 0.5mm, the outer diameter of the rel is not more than 40mm, that RMS7 * 40 anti-roll paper) _ Printer panel description: @Open the door button, press to open the door; @ SEL key, indicator light, for factory setting, do not press; @ Lf key, the green indicator light is the power indicator light, which is always on when the power is turned on; @Roll paper. Install roll paper: Press the door open button © to open the door, close the door panel after loading the paper roll, and slightly expose the head of the roll paper to the door panel. 6.5.2 Disc chart recorder Optional function, please refer to the "Instruction Manual of Chart Recorder" in the accessory bag when matching this function. 3 SMS alarm GSM Optional function, please refer to the "SMS Alarm User Manual" in the accessory bag when matching this function. Please cut off the power before installing the SMS function, otherwise it may cause electric shock6.5.4 Remote alarm and RS485 interface The remote alarm terminal is installed (see the figure below) on the back or right side of the cabinet, and the alarm signal is output by the terminal. The carrying capacity of this terminal is DC 30V, 2A; users can choose normally open (N.O.), normally closed (N.C.), common terminal (COM) according to their needs. Remote alam tenia 6.5.5 Freezer rack & freezer box Quantity internal dimensions] Shelf/Inner | of Dimensions of | Quantity of Freezer (w*D*H) door | Freezer] Freezer rack box(2 inches) rack UPQ 3006 | 750°696*1286mm 485 685*140*293 500(5*5*20) 6.5.6 CO2 backup system The CO2 backup system is an auxiliary reffigeration system that uses liquid carbon dioxide refrigeration to provide reftigeration assistance to the equipment in the event of power failure or refrigeration failure to ensure that the temperature in the equipment is maintained within the required temperature range for a certain period of time. ‘When the equipment is working normally, the CO2 backup system is in standby; When the equipment is powered off, the system uses its own rechargeable battery to work, and sprays liquid carbon dioxide into the refrigeration equipment at intervals to achieve the cooling effect; When the equipment has a cooling failure, the backup system can be forced to work through the forced operation switch to provide cooling. For installation and use, please refer to the operation steps in the instruction manual attached to the device. Ct) Attention please! It must be ensured that liquid carbon dioxide is contained in the cylinder. The temperature of liquid carbon dioxide is relatively low. Pay attention to safety during installation and use to prevent frostbite. The carbon dioxide backup system is a backup system, which should be tested once a month to prevent system failure from affecting its use. The use environment needs to be well ventilated to avoid physical discomfort due to excessive carbon dioxide and insufficient oxygen.7. Defrost eUnused e Maintenance 7.1 Maintenance of equipment + Defrosting: When the frost layer on the inner surface of the device is too thick, it will affect the cooling effect and increase power consumption. Use the defrosting shovel attached to remove the surface frost. Sharp metal utensils should not be used to defrost to avoid damage to the device. Before defrosting, please cut off the power and transfer the contents of the box After defrosting, tu on the power first, and then put the items back into the fully cooled equipment (remove special protective gloves to avoid frostbite); * Cleaning and maintenance: The equipment should be cleaned and maintained regularly (for safety, please unplug the power plug), and wipe the inner and outer surfaces of the cabinet with a soft, warm cloth + Cleaning the filter: regularly clean the dust on the filter to ensure heat dissipation. For the cleaning method: 1. Move the upper right comer of the front ventilation panel ‘outwards and open the ventilation panel; 2. Pull the filter upward to extract the filter (see the figure below, there are two types of left and right, please refer to the actual product); 3. Gently brush off the dust on the surface with a brush or rinse with tap water, dry it and reinstall it. 4a Warning: To prevent electric shock or injury, be sure to cut off the power before any repairs and maintenance of the equipment. Make sure not to inhale the surrounding drugs or suspended particles when maintaining the equipment, otherwise it will harm your health. oe Attention please! Do not directly sprinkle water on the box, so as not to cause the insulation performance of electrical components and metal parts to rust. Do not use hot water and corrosive cleaners or organic solvents to clean the cabinet, Do not place heavy objects on top of the device, as the device may deform under pressure.7.2 Unused ‘© Stop using: If the device is stored in an unsupervised area for a long time without use, the power supply should be cut off and wiped with a warm and damp cloth to clean the inner and outer surfaces of the box, dry and sealed; the device must be locked to ensure that children cannot open Box door. Disposal: When the equipment reaches the service life, it should be discarded. It must be handed over to a qualified professional recycling agency for disposal in accordance with local laws and regulations. Non-professionals are not allowed to disassemble and disassemble the device without authorization; the scrapped device should be placed in a designated area where children cannot reach to avoid danger. 7.3 Maintenance, replacement and recovery of rechargeable batteries (optional) 7.3.1 Maintenance 1. In order to prolong the service life of the battery, it is necessary to avoid the product being idle for a long time, and let the product run for more than 24 hours every month to facilitate charging. @® When the equipment is not used for a long time, it should be connected to the working power supply regularly (usually once a month) and turn on the power lock switch to let the equipment run for a period of time to complete the charging, and the charging time for each time is not less than 24 hours; @ When the working power supply is interrupted, the device power lock switch should be turned off in time, otherwise it will cause the battery to lose power, and in serious cases will cause permanent damage to the battery; @ The main power switch must be turned off during a long-term power outage or during transportation, otherwise the battery will lose power or be permanently damaged due to long-term discharge, and the display will be abnormal after re-powering; © The battery is a consumable and the life span is about 2 years. If the battery is used improperly or reaches the service life of the battery, it will cause a low battery alarm (it does not affect the cooling but there is an alarm failure and will invalidate the power failure alarm function, please contact our after-sales personnel for replacement) 7.3.2 Replacement and recovery ‘* Tum offthe power switch and pull the power plug from the socket; * Forthe product, use a screwdriver to remove the screws of the back cover of the rack (see the lower left figure); remove the right side cover of the cabinet by pressing the plastic fixing buckle Board (see the lower right picture); Note: It is not necessary to open the electrical box to replace the battery. There are high- voltage electrical components in the electrical box. Before opening, you must turn off the power supply and unplug the power supply and close the storage box Power switch, open the electrical box must be completed by a qualified engineer or maintenance personnel. Unplug the battery connection cable. The battery is located on the right side of the compressor bottom plate; the battery is located on the electrical installation board Note: Observe the battery before removing the battery fixing wire the order of the positive and negative levels and the connecting line prevents the installation of a new battery with the positive and negative poles reversed to bum the control system. Generally, the red line connects the battery positive level and the black line connects the negative level.Remove the fixing screws on the battery fixing plate with a screwdriver and take out the battery; ‘The newly replaced battery should be BT-12M4.0AC (12V 4.0Ah); The replaced battery is recyclable; please contact your local battery recycling agency for disposal Tip: To ensure that the battery replacement meets the requirements of the control system and avoids the impact of improper operation on the system, please contact our after-sales personnel for replacement or guidance. Battery - After removing the screws on the right side of the rack, remove the rack, AMC micelle) ‘Any product has the possibility of failure. Please observe the operation of the Ultra-low temperature freezer in the process of use. If there is any abnormality, please check and compare the errors with the following table. If you can't fix the issue, Please inform our service center in time We will serve you wholeheartedly to avoid any losses. Term of use: 10 years ‘Troubles Reason and solutions Ln Thema dome’ wok oleae ete power epply voltage 0 low orto ish ‘olga nowt? Prercmeneieieeaire Tepe > Whee te dori oe or fhe dari pen i oe? eienveie 5 Do you ne to samy tee a on ine as bastonphads High ambient joer temperature alarm — wl oud teNote: If the malfunction is not eliminated after checking the above items or the malfunction is not shown on the above table, contact Laboquest sales representative or agent. Follows are not failure: ‘There will be a slight crash sound of the compressor switch when the compressor is starting and stopping. The cooling time is longer than normal for the first use of the freezer. These are normal phenomenon, In the wet rainy season, there will be a little frost forming on the surface of the freezer; use the dry cloth to wipe it off will be OK. ‘The twice opening of the door should after 5 minutes, otherwise the outside warm air will come in, the negative pressure inside the freezer caused by a sharp decline will make the door difficult to open. ‘A sound of liquid flow inside the freezer is a normal sound of refrigerant circulating. Inner liner opposite of the gasket is a press release area of the freezer, will be some slight crack onside during the cold and hot temperature alternation. It is a normal phenomenon. Do not affect the regular use. Optional with printer, the screen flickers when the printer is printing or the screen is refreshing the data. The screen controller will show system abnormal sometimes when the first time to start of the freezer. It is normal due to that the controller has not completely read the data, it will back to normal after the data reading. If the controller do not show regularly for a long time, should turn off the power switch and restart it. Please clean and disinfect the machine before notifying the maintenance engineer. Transportation or use of the process shall not be violent vibration, collision, to prevent rain. Storage and transportation conditions: ambient temperature: -40°C ~ +55°C, relative humidity: 10% ~ 90%. Warning: this product is made of flammable working medium, It is strictly forbidden to disassemble and repair (especially compressor, refrigeration pipe and other related parts). If there is any fault, it must be repaired by manufacturer service centre.Ae CUE Ue er Loe 9.1 Main Specifications Ambient |ClimateRefrigerant|Rated {Rated [Temper [Effective input Overall tempera |type Voltage |Freque lature [Volume [Power Dimensions Model | tureCc) KV) |mey Range |(L) (Ww) }(mm) (iz) \C) |(w*D*H) uPQ 3006 | 16-32 220 | 50 |-20~-40 885 hoso*1025*1955| 9.2 Package List Name Operation Manual Defrost shovel Number] 1 1 9.3 Circuit Circuit diagram ‘tr there is any product improvement, the technical data and electrical, circuit diagram shall be subjected to the name plate. Laboquest INC. ‘One Westbrook Corporate Center Suite 300, Westchester, IL-60154 wwrw.laboquest.com = [email protected]