Scribd
Upload
14 views

7_segment_code_explanation_fixed

The code sets up an Arduino to control a 7-segment display by configuring pins 3 to 8 as outputs. It attempts to display digits 0-9 using only 4 pins, which is insufficient for a 7-segment display that requires 7 pins for full control. The document outlines problems with the code, including insufficient binary representation and improper segment mapping, and suggests using all 7 pins with a proper mapping for accurate display control.

Uploaded by

aryankothambia
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
14 views

7_segment_code_explanation_fixed

The code sets up an Arduino to control a 7-segment display by configuring pins 3 to 8 as outputs. It attempts to display digits 0-9 using only 4 pins, which is insufficient for a 7-segment display that requires 7 pins for full control. The document outlines problems with the code, including insufficient binary representation and improper segment mapping, and suggests using all 7 pins with a proper mapping for accurate display control.

Uploaded by

aryankothambia
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Explanation of the Code

Your Code:

----------------------

void setup()

for (int i = 3; i <= 8; i++)

pinMode(i, OUTPUT);

void loop()

// display a new digit every second

for (int digit = 0; digit <= 9; digit++)

for (int pin = 4; pin <= 7; pin++)

digitalWrite(pin, (bool)(digit & (1 << pin - 4)));

delay(1000);

1. setup() Function:

----------------------

for (int i = 3; i <= 8; i++)

pinMode(i, OUTPUT);
What Happens:

- The for loop iterates over pins 3, 4, 5, 6, 7, and 8, setting each one as an output pin using

pinMode(i, OUTPUT).

- Purpose: These pins are used to control the segments of the 7-segment display.

2. loop() Function:

----------------------

The loop() function continuously runs and displays digits (0-9) on a 7-segment display.

Outer Loop:

for (int digit = 0; digit <= 9; digit++)

- This loop iterates over the numbers 0-9.

- The variable digit represents the current number to display.

- Inside this loop, we configure the segments of the display for the given number.

Inner Loop:

for (int pin = 4; pin <= 7; pin++)

digitalWrite(pin, (bool)(digit & (1 << pin - 4)));

Explanation:

1. The inner loop iterates over pins 4, 5, 6, 7, which are used to encode the binary representation of

the number (digit).

Key Expression:

(digit & (1 << pin - 4))


- 1 << (pin - 4):

This shifts the binary value 1 to the left by (pin - 4) places.

- digit & (1 << pin - 4):

This performs a bitwise AND between the number digit and the shifted value.

delay(1000):

- After configuring the pins for a specific digit, the delay(1000) function pauses execution for 1

second.

Backend Workings:

----------------------

The Arduino board interacts with the 7-segment display based on the binary signals sent to the pins.

Problems in the Code:

----------------------

1. Binary Representation is Insufficient:

- A 7-segment display requires 7 control pins (one for each segment a-g), but the code uses only 4

pins (4-7).

2. Segments Are Not Mapped Properly:

- The code doesn't define how each binary bit maps to specific segments.

To Properly Control a 7-Segment Display:

------------------------------------------

1. Define which pins control each segment (a-g).

2. Create a mapping from digits (0-9) to their corresponding segments.


3. Use all 7 pins (e.g., pins 2-8) to set the state of each segment individually.

If further clarification or modifications are needed, feel free to ask!

You might also like