PTZ-HD-20

High Definition Pan Tilt Zoom Camera

w/ Infrared Night Vision

User Manual
 WARNINGS AND CAUTIONS

WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.

CAUTION

EXPLANATION OF GRAPHICAL SYMBOLS

The lighting flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user the presence of non-insulated “dangerous voltage” within the
product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric
shock to different persons.

The exclamation point within an equilateral triangle, is intended to alert the user
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying this product
PRECAUTIONS:
l Persons without technical qualifications should not attempt to operate this dome
device before reading this manual thoroughly.

l Remove any power to the dome before attempting any operations or adjustments
inside the dome cover to avoid potential damage to the mechanism.

l Inside the dome cover there are precision optical and electrical devices. Heavy
pressure, shock and other sudden adjustments or operations should be avoided.
Otherwise, you may cause irreparable damage to the product.

l Please DO NOT remove or disassemble any internal parts of the video camera to
avoid normal operation and possibly void the warranty. There are no serviceable
parts inside the camera.

l All electrical connections to the dome should be made in strict accordance with the
attached labels and wiring instructions in this manual. Failure to do so may damage
the dome beyond repair and void the warranty.

l For outdoor installation especially in high places or poles, it is highly recommended

that the proper lightning rod and surge suppressors are installed before the dome is
entered into service.

l Please do not use the product under circumstances where the limits exceed the
maximum specified temperature, humidity or power supply specifications.
IMPORTANT SAFEGUARDS
1. Read these instructions before attempting installation or operation of dome device
2. Keep these instructions for future reference
3. Heed all warnings and adhere to electrical specifications Follow all instructions
4. Clean only with non abrasive dry cotton cloth, lint free and approved acrylic cleaners
5. Should the lens of the camera become dirty, use special lens cleaning cloth and solution to
properly clean it.
6. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions
7. Use only attachments or accessories specified by the manufacturer
8. Verify that the surface you are planning to use for attaching the dome can adequately
support the weight of the device and mounting hardware
9. Protect this devices against lighting storms with proper power supplies
10. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, when liquid traces are present, or the presence of loose objects
is evident or if the device does not function properly, or has received sever impact or has
been dropped accidentally.
11. Indoor dome is for indoor use only and not suitable for outdoor or high humidity locations.
Do not use this product under circumstances exceeding specified temperature and humidity
ratings.
12. Avoid pointing the camera directly to the sun or other extremely bright objects for
prolonged period of time avoiding the risk of permanent damages to the imaging sensor.
13. The attached instructions are for use by qualified personnel only. To reduce the risks of
electric shock do not perform any servicing other than contained in the operating instructions
unless you are qualified to do so.
14. During usage, user should abide by all electrical safety standards and adhere to electrical
specifications for the operation of the dome. The control cable for RS485 communications
as well as the video signal cables should be isolated from high voltage equipment and or
high voltage cables.
15. Use supplied power supply transformer only.
 INDEX
1 Product Introduction ....................................................................................................... 6
1.1 Package Contents ................................................................................................... 6
1.2 Specification ............................................................................................................ 7
1.3 Function Description ............................................................................................... 8
2 Installation...................................................................................................................... 10
2.1 Coaxial Control ...................................................................................................... 10
2.1.1 AC24V power cable transmission distance and cable requirement.............10
2.2 Bracket Dimensions .............................................................................................. 10
2.2.1 Wall Mounted Bracket ................................................................................. 10
2.2.2 Corner Mounted Bracket ............................................................................. 11
2.2.3 Pole Mounted Bracket ................................................................................. 11
2.2.4 Ceiling Mounted .......................................................................................... 12
2.3 Installation of Brackets. ......................................................................................... 12
2.3.1 Wall Mounted .............................................................................................. 12
2.3.2 Corner Mounted .......................................................................................... 14
2.3.3 Pole Mounted .............................................................................................. 15
2.3.4 Ceiling Mounted .......................................................................................... 15
2.4 Connection ..................................................................................................... 16
3. Function Instruction ..................................................................................................... 17
3.1 Power Up Action .................................................................................................... 17
3.2 Basic Function ....................................................................................................... 17
3.3 Shortcut commands .............................................................................................. 18
3.4 Screen Character Operation ................................................................................. 18
4 OSD Menu ...................................................................................................................... 19
4.1 Menu Index ........................................................................................................... 20
4.2 System Information ............................................................................................... 20
4.3 Dome ..................................................................................................................... 21
4.3.1 Communication ........................................................................................... 21
4.3.2 IR Display .................................................................................................... 21
4.3.3 Guard Tours ................................................................................................ 22
4.3.4 A-B Scan ..................................................................................................... 22
4.3.5 Pan Scan ............................................................................................................ 23
4.3.6 Park Action .................................................................................................. 23
4.3.7 Privacy Zone ............................................................................................... 24
4.3.8 Alarm (Optional) .......................................................................................... 24
 4.3.9 Advanced .................................................................................................... 25
4.4 Camera ................................................................................................................. 25
4.5 Language .............................................................................................................. 26
4.6 Display .................................................................................................................. 26
4.7 Reset ..................................................................................................................... 26
5. Auto Temperature Control ........................................................................................... 27
Appendix Ⅰ Anti-lightning, Anti-surge ......................................................................... 27
Appendix Ⅱ Clean Transparent Cover ......................................................................... 28
Appendix Ⅲ Common Knowledge on RS-485 Bus ...................................................... 28
1. Basic Feature of RS-485bus ................................................................................... 28
2. Mode of Connection and Terminal Resistance ........................................................ 28
Appendix Ⅳ Exception Handling .................................................................................. 29
Copyright Statement ........................................................................................................ 30

* Indicates the functions with default protocol, it might not function by using other protocols
※ Indicates the optional functions, only with certain mode.
1 Product Introduction
1.1 Package Contents
IR Speed dome 1pc
Wall mount bracket 1pc
Power supply 1pc
Screws kits 1pc
User manual 1pc
 1.2 Specification
Speed Dome High Speed Dome Medium Speed Dome
Horizontal Rotation Speed 200°/s 60°/s
Tilt Rotation Speed 100°/s 30°/s
Horizontal Rotation Range 360°
Tilt Rotation Range 93°
Auto Flip Horizontal 180°, Vertical 93°
Auto Control IR LED PWM
A-B Scan User programmable
A-B Scan Speed 01-64speed setting available
360° Scan Speed 01-64speed setting available
Dwell Preset 01-60s interval
Preset Points 220
Go to Preset Speed 01-64speed setting available
Guard Tours 3 groups
Guard Points Max.16 points, dwell time user selectable
Home Pos Time 1-60mins available
Restore as power up/Pan scan/A-B scan/Park
PWR on Action
action/Guard tour group 1-3/No action
Communication Protocol Pelco-D, Pelco-P
Communication RS485 Bus/ Coaxial
Baud Rate 1200/2400/4800/9600bps (Default2400bps)
Privacy Mask Depend on the zoom module
Alarm Optional
Operating Temperature Indoor: 0°~ +40° , Outdoor: -40°~ +60°
Operating Humidity ≤95% Non Condensing
Heater & Blower Auto temperature control
Power DC12V/AC24V (Depend on the model)
Lightning Protection transient voltage 6000V
IR Illumination Distance 100-180m(Depend on the model!)
Power Consumption ≤ 25W
 1.3 Function Description
Super Communication
Address, baud rate and protocol could be changed from OSD.
Privacy Mask
Depend on the zoom nodule. This function allows user to set privacy protected area as
unviewable in the monitoring scope.
Alarming Set
The dome support this feature in optional , details please refer to the OSD menu.
IR Detection Time
Time duration switching from Color to B/W or B/W to Color. It can be set through OSD
Focus
The auto focus enables the camera to focus automatically to maintain clear image. User can
use manual focus to in special condition.
Under the following conditions camera will not auto focus on the camera target:
(1) Target is not the center of the screen;
(2) Attempting to view images that are far and near at the same time;
(3) Target is strongly lighted object, such as neon lamp, etc.;.
(4) Targets are behind the glass covered with water droplets or dust;
(5) Targets are moving quickly;
(6) Monotonous large area targets, such as wall;
(7) Targets are too dark or faint.
BLC
If a bright backlight is present, the target in the picture may appear dark or as a silhouette,
BLC enhance the target in the center of the picture, the dome uses the center of the pictures
to adjust the iris. if there is a bright light source outside this area, it will wash out to white,
the camera will adjust the iris so that the target in the sensitive area will properly exposed.
Iris Control
Factory default is automatic camera aperture, in mode of which camera senses changes in
ambient light through moving and adjust automatically lens aperture to make the brightness
of output image stable.
Users can pressing OPEN or CLOSE iris adjusting keys, manually adjust the aperture size
to get the required picture brightness.
By controlling the keyboard up, down, left, right or zoom to resume auto iris (auto iris is
recommended).
Day/Night Switch
With auto day/night switch function, when the illumination is low the picture will auto switch
from day to night mode and when the illumination is high enough the picture will auto switch
from night to day mode
Ratio Speed
Intelligent pan and tilt speed is variable depend on the zoom factor. When zooming in, the
speed will become slower and when zooming out, the speed will become quicker.
A-B Scan
Dome circularly scan close-up real-time scene according to A-B points at setting speed in
both horizontal and vertical directions.
Pan Scan
Dome 360°clockwise continuous scan the display scene at setting speed in horizontal
direction under the condition that pitch angle remains the same.
Preset
After the dome camera keeps arbitrary PTZ location, it will automatically move to the defined
position when preset is called.
Guard Tours
Dome patrol scans according to certain edited preset order.
Power Off Memory
This feature allows the dome to resume its previous preset or status after power is restored.
By default setting, the dome support power up memory, which improves the reliability and
avoids repeated settings of the parameter.
Park Action
If users don’t operate the dome in set time, it will automatically run preset specific mode
(pan scan, A-B scan, park action, cruise, preserve action etc.).
Zero Alignment
There is a point specified as zero point. When the dome is working, the preset point is not
accurate because of something caused by the operator. User can make the dome
automatically enable the zero alignment by operational order.
Auto Flip
In the manual tracking mode, when a target goes directly beneath the dome, the dome will
automatically rotate 180 degree in horizontal direction to maintain continuity tracking. When
the dome flips, the camera starts moving upward as long as you hold the joystick in the down
position.
2 Installation
2.1 Coaxial Control
The dome supports coaxial control and also supports RS-485 communication signal.
2.1.1 AC24V power cable transmission distance and cable requirement
In general, the power cable has resistance, there are internal losses when transmitting the
voltage, the longer of the cable used, the smaller the wire diameter, the worse loss will suffer.
In order to avoid losses of cable causing low voltage and keep the dome work properly,
when processing wiring please refer to the requirement below:

Cable diameter 0.5mm²(20#) 1.0mm²(18#) 1.5mm²(16#) 2.5mm²(14#)

Dome distance 11m(37ft) 18m(60ft) 29m(95ft) 46m(152ft)

For example, if a dome is 35 meters away from the power supply , power cable used must
be more than 2.5mm², otherwise, the dome may suffer insufficient power supply and could
not work properly.
Remark: The dome with DC12V should be less than 3 meters away from power supply.

2.2 Bracket Dimensions

2.2.1 Wall Mounted Bracket
2.2.2 Corner Mounted Bracket

2.2.3 Pole Mounted Bracket

2.2.4 Ceiling Mounted

 2.3 Installation of Brackets.
2.3.1 Wall Mounted

Fig 1
Installation conditions:
Wall mounted dome can be used in the hard wall structure whose thickness should be enough
to install expansion bolt in indoor and outdoor environment. The wall can bear at least 4 times
the weight of the dome. Install wall hanging bracket:
a. As shown in fig 2, with the installation holes in the underside of the wall hanging bracket as
pattern, draw punched locations and punch.

Fig 2
b. As shown in fig 3, fix the wall hanging bracket on the wall with wire and cable through it.

Fig 3
 2.3.2 Corner Mounted

Fig 11
Installation conditions:
Corner mounted dome can be used in the hard wall structure with an angle of 90° whose
thickness should be enough to install expansion bolt in indoor and outdoor environment. The
wall can bear at least 4 times the weight of the dome. Install corner mounted attachment and
wall hanging bracket:
a. As shown in fig 12, with the installation holes in the corner mounted attachment as pattern,
draw punched locations on the wall with an angle of 90°and punch to install expansion bolt.

Fig 12
b. As shown in fig 13, use M8 screw nut to fix the base of corner mounted on the wall with all
cables through the center holes of the corner mounted, marine glue and bracket. Enough wiring
length should be left.

Fig 13
c. As shown in fig 14, fix the wall hanging bracket with all cables power through it on the corner
mounted attachment.

Fig 14
2.3.3 Pole Mounted

Fig 15
Installation conditions:
Pole mounted dome can be used in the hard pole structure in indoor and outdoor environment
whose diameter should match the installation size of stainless hose clamps. Factory default is 6
inches stainless hose clamps (fit φ130-152mm pillar). The pole structure can bear at least 4
times the weight of the dome. Install corner mounted attachment and wall hanging bracket:
a. As shown in fig 16, use the stainless hose clamps to fix the pole mounted attachment with all
cable through it on the pole structure.

Fig 16
b. As shown in fig 17, fix the wall hanging bracket with all cables through it on the pole mounted
attachment.

Fig 17
2.3.4 Ceiling Mounted

Fig
Installation conditions:
Ceiling mounted dome with thick pole can be used in the hard ceiling structure whose thickness
should be enough to install expansion bolt in indoor and outdoor environment. The ceiling can
bear at least 4 times the weight of the dome. Install the base of ceiling and boom:
a. As shown in fig 19, with the installation holes in the base of ceiling as pattern, draw punched
locations in the ceiling and punch to install M6 expansion bolt.

Fig 19
b. As shown in fig 20, at first unscrew the M4 screw at the side of the base of ceiling and split
the base of ceiling and boom. Then make the three groups of cables of power, video/control and
alarming into the side recessing seal groove of the ceiling connector bottom and through the
core hole of the base of ceiling mounted. Fix the base of hang ceiling on the ceiling board.

Fig 20
Note: If the dome is used in the outdoor conditions, use the silica gel on the faying surface of
the base of hang ceiling and the ceiling board and around the out-holes to be sure water proof
c. As shown in the fig 21, tighten the boom with electrical wire and cable through it on the base
of ceiling and screw up the M4 screw.

Fig 21
Note: If the dome is used in the outdoor conditions, after using enough raw materials to wrap
the thread at the upper end of boom, tighten the boom on the base of ceiling. Use the silica gel
around the joint sleeve and connector of the boom to be sure water proof

2.4 Connection
Connection of RS485
Before connecting, please turn off the power and read carefully the instructions of all
connected devices.

Fig 24
3. Function Instruction
3.1 Power Up Action

<SYSTEM> <SYSTEM>
MFG MFG
PROTOCOL AUTO PROTOCOL AUTO
DOME ID DOME ID
COMM COMM
VERSION VERSION
TEMPERATURE TEMPERATURE
DETECTING… PAN: XXX TILT: XXX

Power Up Self Testing Pan, Tilt,

Camera Self-test Completion
² Pan action: Pan rotate in certain direction and stop in zero coordinate.
² Tilt action: Tilt rotate in certain direction and stop in zero coordinate.
² Lens action: Lens zooming out to be max.
² From running the action above to power up mode completion, power up self-testing
finishes.

3.2 Basic Function

Dome Running
Control joystick or up, down, left and right key in the keyboard.
Zoom
Press ZOOM- button to make the lens farther and minify the scene.
Press ZOOM+ button to make the lens closer and magnify the scene.
Focus
Press FOCUS- button , close shot will become clearer while long shot will become fuzzy.
Press FOCUS+ button , long shot will become clearer while close shot will become fuzzy.
Iris
Press IRIS- to shrink the iris and decrease the image brightness gradually.
Press IRIS+ to enlarge the iris and increase the image brightness gradually.
Preset Point
Setting preset to press buttons “preset” + ”number” + ”enter”.
Calling preset to press buttons “call” + ”number” + ”enter”.
Deleting preset to press buttons “clear” + ”number” + ”enter”.
Remark: Some preset points are occupied by special functions.
Overview for 4 in 1 products(Support AHD/ CVI/ TVI/ CVBS output)
Basic on single HD Analog coaxial series,( AHD/TVI/CVI/CVBS series), the 4 in 1 series have
combined the 4 single output signal together,it can be switched the video signal freely between
the AHD/TVI/CVI/CVBS by shortcut commends. This gives great convenience for all
application, reduce cost, and easy for maintenance.

Switch video signal:Two ways to switch the video signal

Call twice preset 102 to enter the Sub OSD menu.
Press “Zoom+” or “Zoom-” to move the option to the item 1.
Press the “Focus+” or ”Focus-” to switch to the signal output needed,
Then press “ zoom+ or Zoom- to the item 6“ RETURN”
Call twice 102 again to exit from the Sub OSD menu.

Direct shortcut commend to switch the video output signal needed. Please Reference to the
below table for details.

Remark: Please do not change the parameter of the Sub OSD menu randomly to avoid any
unexpected happen.

Please reboot the PTZ after switch the video signal output.

3.3 Shortcut commands

Shortcut commends are complaince with Pelco D and its Extended protocol. User can use the
shortcut commend to enable the function directly.

Preset No. Function Preset No. Function

81（41） Auto day/ night 97 Call tour 2
82（42） Switch to night 98（38） Call tour 1
83 Switch to day 99（39） Pan scan
84 Force on far light Twice 137 Switch to AHD
85 Force on near light Twice 138 Switch to TVI
92 A-B Scan Twice 139 Switch to CVI
94 OSD off Twice 140 Switch to CVBS
95 OSD on Twice 115 Switch to NTSC
96 Call tour 3 Twice 116 Switch to PAL

Remark:Because the limit of COC protocol,it is possible that some of the shortcut commend
are not valid when connected to some of the controlled equipment.

If no video or video is stuck in black and white, please make sure the video output of the
signal, the TV system ( NTSC/Pal) between the PTZ and the controlled equipment to be
consistent, if not, please adjust accordingly.

3.4 Screen Character Operation

Call preset 95 to enter the OSD, call preset 94 to exit the OSD.
² Up or Down: Move the option of the OSD, change the set point.
² Right: Enter the option, select the item or confirm .
² Left: Return to main menu or cancel.
² Angle Display: XXX.XX(pan)/XXX.XX(tilt)
² IR Display: Display on the lower right corner of the screen.
Remark: 1. Items with“< >” mean they have sub menu.
2. “→”means the cursor selecting some option.
3. “※” means editing the content of some option selected.
4. When entering the setting page in menu, it is useless to call preset 94 to exit
the menu directly. Such as the sub-menu <SET> in menu <GUARD TOUR SET>.
4 OSD Menu
4.1 Menu Index
 4.2 System Information

<MAIN MENU>
<SYSTEM>
<DOME>
<CAMERA>
<LANGUAGE>
<DISPLAY>
<RESET>
EXIT

Get into the Menu Screen

<SYSTEM>
MFG
PROTOCOL AUTO
DOME ID 001
COMM 2400.N.8.1
VERSION
TEMPERATURE
EXIT

MFG: Max 15 characters displayed on the screen.

PROTOCOL: Display the protocol of the dome
DOME ID: Display the dome address
COMM Form: Baud rate. Check bit. Data bit. Start bit
VERSION: Version will update along with the product upgrading
TEMPERATURE: Display the temperature of the camera, it changes along with the
temperature of the camera, the data is unchangeable by manual.
Remark: Protocol, ID
and COMM all can be set in menu <COMM>.

4.3 Dome
<DOME>
<COMM>
<IR DISPLAY>
<GUARD TOURS>
<A-B SCAN>
<PAN SCAN>
<PARK ACTION>
<PRIVACY ZONE>
<ALARM>
<ADVANCED>
EXIT
 4.3.1 Communication

<COMM> <COMM RESET>

DEVICE ID
CHECK ID 000000 RESET TO DIAL THE CODE
TARGET ID 001
SOFT PROTOCOL AUTO
BAUD RATE 2400BPS
<COMM RESET>
SAVE YES
EXIT EXIT

DEVICE ID: It is sole and auto generated by system.

CHECK ID: To change the TARGET ID, please input the CHECK ID exactly same as the
DEVICE ID displays on the screen.
TARGET ID: Target ID is available from 001 to 250 and used to distinguish several domes
of same ID.
SOFT PROTOCOL: Soft protocol is auto, Pelco-D and Pelco-P available
BAUD RATE: 1200BPS, 2400BPS, 4800BPS, 9600BPS available
<COMM RESET>: As shown in fig 4.3.1.2,choose “ YES” ,the dome will save the setting
automatically and restart
SAVE: After saving, the dome will reboot. Communication setting is enable.

4.3.2 IR Display

<IR DISPLAY>
WORKING MODE AUTO
TESTING TIME 08S
OUTPUT POWER 100%
ILLUMINATION ON 3
AMBIENT LIGHT
IR SWITCH ZOOM 06

EXIT
WORKING MODE: IR Working mode has auto, black/white, color selectable. Default is
auto.
TESTING TIME: On IR auto working mode and the programmed time, the IR will execute
programmed action accordingly, eg. Switch from day to night or from night to day. The
detection time is from 2s to 15s selectable.
OUTPUT POWER: Output power has 40%,60%,80%,100% for selection!
ILLUMINATION ON: Illumination on is 1 to15 grade selectable and default is 3. On the
auto IR working mode, if the illumination on level is less than the ambient light, the picture
will change to color, the IR illumination will turn off automatically. If the illumination on level
is more than the ambient light, the picture will change to black , the IR illumination will turn
on automatically.
AMBIENT LIGHT: Ambient light is a system data. User can not change it manually. It
changes according to the environment all the time. The data will refresh every time when
user enter the OSD. It is from 0 to 50 grade.
IR SWITCH ZOOM: When zoom value reaches to the demanded setting, the IR LEDs with
auto switch from near illumination to far illumination, zoom value option from 01-10
4.3.3 Guard Tours

<GUARD TOURS> <GUARD TOUR 01>

GUARD TOUR 01 ID POINT TIME(S) SPEED
<SETTING> 1 01 06 64
INIT 2 02 06 64
RUNNING 3 03 06 64
DELETE 4 04 06 64
5 05 06 64
6 06 06 64
7 07 06 64
EXIT 8 08 06 64
GUARD TOUR: Total 3 guard tours selectable: 01, 02, 03.
SETTING: Each guard tour includes max 16 presets. The number of the preset is from 0-
64, but 0 is not valid. Dwell time is 1 to 60s selectable. Speed is 1 to 64 grade selectable.
INIT: After initial, preset point, dwell time and speed will resume to default..
RUNNING: Running the present guard tour.
DELETE: Delete the guard tour set. After deleted, the present preset points in the guard
tours all display as 0. While the exact preset point information doesn’t be deleted. So it is
convenient for user to select the preset point needing to be guarded tour.
4.3.4 A-B Scan

<A-B SCAN> A-B SCAN

PRESET A 01 RUNNING…
PRESET B 02 LEFT KEY TO EXIT
SCAN SPEED 20
DWELL TIME 06S
RUNNING PAN：XXX TILT：XX
DELETE
EXIT

PRESET A: On A-B scan, A point can be preset from 0 to 64.

PRESET B: On A-B scan, B point can be preset from 0 to 64.
SCAN SPEED: A-B scan speed is 1 to 64 grade selectable.
DWELL TIME: Dwell time between A to B is 2s to 60s selectable.
RUNNING: Running the A-B scan. Check Fig. 4.3.4.2.
DELETE: After deleted, the preset points of A and B display as 0. While the exact preset
point information doesn’t be deleted. So it is convenient for user to select the preset point
needing to be scanned. Speed and dwell time will reset as default setting.
4.3.5 Pan Scan

<PAN SCAN> PAN SCAN

PAN SCAN SPEED 20 RUNNING…
INIT LEFT KEY TO EXIT
RUNNING
EXIT PAN: XXX TILT: XX

PAN SCAN SPEED: Pan scan speed is 1 to 64 grade selectable.

INIT: Reset the scan speed and tilt degree as default setting.
RUNNING: Running the scan speed and tilt degree set.
4.3.6 Park Action

<PARK ACTION> <PARK ACTION>

PARK MODE OFF
PARK TIME 01M
<SETTING>
PRESET 1: SAVE
RUNNING
PRESET 2: BACK
DELETE

EXIT

PARK MODE: Park mode includes OFF, Park action, A-B scan, Pan scan, guard tour 01,
guard tour 02, guard tour 03 and Preserve action.
When park mode is OFF status, the dome doesn’t run park mode.
When park mode is PRESERVE ACTION status, it records previous action
order(A-B scan, Pan scan, Guard tour 01, Guard tour 02, Guard tour 03).
Example: Running A-B scan at first, when the action stops unexpectedly, it enters the park
mode to continue to run A-B scan.
PARK TIME: Park time is 01~60 Mins selectable.
SETTING: After entering the OSD menu, as 4.3.6.2, move to the desired position and save
the settings.
RUNNING: Running the park action, if there is no setting, system will remind that “Please
set park action”.
DELETE: Delete the settings.
 4.3.7 Privacy Zone

<PRIVACY ZONE> <PRIVACY ZONE> <PRIVACY ZONE>

MASK NO. 01
MASK OFF PRIVACY PROPOSED
<SETTING> PRESET 1: SAVE TO OPEN

EXIT

MASK NO.: Mask No. depends on the number of the module supported. The selective
range of Sony is from 1 to 24.
MASK: Mask has on and off selectable.
SETTING: Set the specific parameter of present mask NO. And call preset 1 to save the
settings.
Direction operation—Modify the coordinate of dome
Zoom operation—Modify the size of scenery
Iris operation—Modify the size of privacy zone
Remark: The mask size is better more than double the target size. If needing to modify mask
NO.02, set it again. If needing to stop it, set mask to OFF status.
If the module doesn’t support privacy mask, the screen will display the interface as Fig.
4.3.7.3.
4.3.8 Alarm (Optional)

<ALARM>
ALARM OFF
PATROL TIME 06S
ALARM LINKAGE OFF
ALARM 1 01
ALARM 2 02
ALARM 3 03
ALARM 4 04
RELEASE TIME OFF
EXIT

ALARM: Alarm has OFF and ON selectable.

PATROL TIME: Patrol time is 2~60s selectable.
ALARM LINKAGE: Alarm linkage has OFF and ON selectable.
ALARM 1: To run alarm 1, presets 1-64 are available.
ALARM 2: To run alarm 2, presets 1-64 are available.
ALARM 3: To run alarm 3, presets 1-64 are available.
ALARM 4: To run alarm 4, presets 1-64 are available.
RELEASE TIME: Alarming release time, 2-60s selectable, the default is OFF.

4.3.9 Advanced

<ADVANCED>
PWR ON ACTION MEMORY
RATIO SPEED ON
AUTO FLIP ON
WIPER MODE OFF
WIPER SPEED 5
WIPER TIMES 2
<OTHERS>
EXIT

PWR ON ACTION: Power on action can be set as Memory, A-B scan, Pan scan, Park
action, Guard tour 01, Guard tour 02, Guard tour 03 and No action.
RATIO SPEED: Ratio speed can be set as ON or OFF status.
AUTO FLIP: Auto flip can be set as ON or OFF status.
WIPER MODE: Wiper mode can be set as ON or OFF status.
WIPER SPEED: Wiper speed 1-5 level adjustable.
WIPER TIMES: Wiper times 1-5 times adjustable.
<OTHERS>: Set other options.

4.4 Camera
<CAMERA>
CAM AUTO
ZOOM SPEED
QUICK
DIGITAL ZOOM OFF
FOCUS AUTO
IRIS AUTO
BLC OFF
FREEZE OFF
CAM: Display the EXIT information of module
supported by this dome.
ZOOM SPEED: Zoom speed is quick and slow selectable.
DIGITAL ZOOM: Digital zoom is on/off selectable.
FOCUS: Focus is auto and manual selectable
IRIS: Iris is auto and manual selectable
BLC: BLC is ON and OFF selectable
FREEZE: Video freeze is ON and OFF selectable
Remark: Only if those functions are available on the present module, the user can use them.

4.5 Language
<LANGUAGE>
LANGUAGE ENGLISH
EXIT
LANGUAGE: Language can be set as Chinese or English. Default settings is English.

4.6 Display

<DISPLAY>
SYSTEM PAL
P AND T ON
ACTION ON
IR ON
DOME ID ON
COMM ON
EXIT

SYSTEML: Video system includes NTSC and PAL. N means NTSC and P means PAL.
P AND T: On screen, it displays the pan and tilt degree, user can enable or disable it.
ACTION: On the screen, it displays the current action, such as A-B scan, Call preset, Save
preset, Call park action, Pan scan etc. User can enable or disable it
IR: IR is ON and OFF selectable.
DOME ID: At the top left corner of screen, it displays the dome ID. User can enable or disable
it.
COMM: At the top left corner of screen, it displays the dome communication information. User
can enable or disable it.

4.7 Reset
<RESET> <DOME RESTART>
<DOME RESTART> CONFIRM: Save data,
<SYS DATA> dome restart
<CAM DATA>
<PRESET> EXIT
EXIT

<SYS DATA> <CAM DATA>

CONFIRM: Factory default CONFIRM: Factory default
EXIT EXIT
 <PRESET>
CONFIRM: DEL ALL
PRESETS
CONFIRM 1: DEL 01 TO 16
CONFIRM 2: DEL 17 TO 32
CONFIRM 3: DEL 33 TO 48
CONFIRM 4: DEL 49 TO 64
EXIT
CONFIRM: Delete the presets information saved by the dome.

5. Auto Temperature Control

This product has built-in fan and heater, which accordingly cool or heat through temperature
sensitive circuit inside the dome.

Appendix Ⅰ Anti-lightning, Anti-surge

This product is extremely air discharge and lightning protection with TVS tube technology,
which can effectively prevent the transient lightning below voltage 6000V, surge and
damages caused by other types of pulse signals.
However, necessary protective measures should be made in the premise of ensuring
electrical safety for outdoor installation according to the actual situation :
l Signal transmission line must be at least 50 meters far away from the high-voltage
equipment or high voltage cable.
l Try to choose outdoor wiring laid down along the roof line.
l Way of sealed steel pipe buried wiring is used in the area which opened, and steel
pipe units grounded in one point. Overhead wiring is absolutely prohibited.
l In the strong thunderstorms area or areas with high induced voltage (such as high
voltage substations), measure of installation of additional high power lightning protection
equipment and lightning rod must be taken.
l Lightning protection and grounding of outdoor devices and lines must take the
lightning-protection requirements of buildings into consideration, and comply with the
related national standards and industry standards.
l System must be equipotential grounding. Grounding device must meet dual
requirements of anti-interference and electrical safety, and should not be shorted or
mixed with the adjacent lines in the strong power grid. When system is independently
grounded, grounding impedance should be less than 4Ω, and cross-sectional area of
 grounding conductor must be not less than 25mm2.

Fig 1

Appendix Ⅱ Clean Transparent Cover

In order to assure a clear image of dome, the under cover of dome should be cleaned
regularly.
l Be careful when cleaning and hold the outer ring of under cover by hands to avoid
directly touching with it. Because the acid sweat of finger membrane may corrode the
surface coating of under cover. Hard tool scratching the under cover may lead to
blurring the images of dome so that affecting image quality.
l Please use a soft enough dry cloth or other alternatives to wipe internal and external
surface.
l If dirt is serious, user can use a mild detergent. Any senior furniture cleaning
products can be used to clean the under cover.

Appendix Ⅲ Common Knowledge on RS-485 Bus

1. Basic Feature of RS-485bus
According to industry bus standard of RS-485, RS-485 bus is half-duplex communication
bus with the characteristic impedance of 120Ω, whose maximum load capacity is 32
payloads (including the master device and the controlled device).

2. Mode of Connection and Terminal Resistance

2.1 Industry standard of RS485 bus requires that connection in a daisy chain should be
used between the devices with 120Ω terminal resistances connected at the both ends.
As shown in fig. 26 and fig. 27 is simplified connection, but the distance of part "D" shall not
beyond 7 meters.
 Fig 2 Fig 3
2.2 120Ω terminal resistance is connected as shown in fig 2.
120Ω terminal resistance is available in the circuit board and the connection is shown as
following:
When needing to connect 120Ω resistance, toggle the 8th bit of DIP switch SW2 to "ON" .
This way the 120Ω resistance is connected to the circuit.

Appendix Ⅳ Exception Handling

Issue Possible Reason Solution
After power Cable harness is improperly Verify that the orientation of the
is applied, connected connector input
there is no
motion Input power voltage is too low Verify the voltage of the input power
(self-test)
and no video
Power supply is not work Change a new power supply
image.
Set the correct protocol, baud rate and
Self-test is Wrong communication settings
address of dome device
normal, but
cannot Verify the polarity of the RS485
Improper connection of control
control dome connection as per the instruction
cable (polarity)
manual
Mechanical obstruction Verify and correct it
Noise after Camera module is not installed
Correct
self-testing correct
Low power Change the correct power supply
Check the power supply or make sure
Low power
Image is not the power input is DC 12V
stable Video cable is improperly
Verify the contact of the video cable
contact
Image is Camera is on manual focus Change to auto focus
blurring The lens is dusted Clean the lens
Power is too low Change the DC 12V Power supply
Communication distance is too Make sure the distance is in the
Control to
long allowed range
the
dome is not RS485 cable is not properly
Make the RS485 is properly contact
smooth contact
Make sure the connected dome is in
Too many domes connected
the allowed quantity
Copyright Statement
This copyright is merely belong to the manufacturer. Without permission, please don’t
plagiarize or copy the contents of this book in any form or by any means.
The company follows the policy of continuous development. Therefore, the company
reserves the right to modify or improve the products described in this manual without notice.
The content of manual is offered according to the "current state". Unless applicable law
otherwise specified, the company does not make any kind of clear or tacit reassurance about
the accuracy, reliability and contents of this manual. The company reserves the right to
revise or recoup this manual at any time without notice.