SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

H RESTRAINTS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SECTION SRS B

E
CONTENTS
PRECAUTIONS .......................................................... 3 WITHOUT CONSULT-LLL ................................... 26 F
Precautions for Supplemental Restraint System HOW TO ERASE SELF-DIAGNOSTIC
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- RESULTS ............................................................ 26
SIONER” .................................................................. 3 SRS Operation Check (USER MODE) ................... 27 G
Precautions for SRS “AIR BAG” and “SEAT BELT DIAGNOSTIC PROCEDURE .............................. 27
PRE-TENSIONER” Service ..................................... 3 Trouble Diagnosis with CONSULT-IlI ...................... 29
Precautions for Battery Service ................................ 3 DIAGNOSTIC PROCEDURE .............................. 29
SRS
Occupant Classification System Precaution ............ 3 Trouble Diagnosis without CONSULT-IlI ................. 33
PREPARATION ........................................................... 4 DIAGNOSTIC PROCEDURE .............................. 33
Commercial Service Tools ........................................ 4 WARNING LAMP FLASH CODE CHART ........... 33
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) ....... 5 Trouble Diagnosis: “AIR BAG” Warning Lamp Does I
SRS Configuration ................................................... 5 Not Turn OFF ......................................................... 37
Front Seat Belt Pre-tensioner with Load Limiter ..... 6 DIAGNOSTIC PROCEDURE .............................. 37
Front Side Air Bag .................................................... 6 Trouble Diagnosis: “AIR BAG” Warning Lamp Does J
Side Curtain Air Bag/for Coupe ................................ 6 Not Turn ON ........................................................... 38
Warning Lamp .......................................................... 6 DIAGNOSTIC PROCEDURE .............................. 38
Occupant Classification System (OCS) ................... 7 Trouble Diagnosis: Passenger Seat belt Warning
K
Passenger Air Bag Status Condition ........................ 7 System .................................................................... 39
Component Parts of Occupant Classification Sys- DRIVER AIR BAG MODULE .................................... 40
tem ........................................................................... 7 Removal and Installation ........................................ 40
Passenger Seat belt Warning System ...................... 8 REMOVAL ........................................................... 40 L
TROUBLE DIAGNOSIS .............................................. 9 INSTALLATION ................................................... 41
Trouble Diagnosis Introduction ................................. 9 SPIRAL CABLE ........................................................ 42
DIAGNOSIS FUNCTION ....................................... 9 Removal and Installation ........................................ 42 M
HOW TO PERFORM TROUBLE DIAGNOSES REMOVAL ........................................................... 42
FOR QUICK AND ACCURATE REPAIR ............... 9 INSTALLATION ................................................... 43
WORK FLOW ...................................................... 10 FRONT PASSENGER AIR BAG MODULE .............. 44
Component Parts Location ......................................11 Removal and Installation ........................................ 44
Schematic .............................................................. 12 REMOVAL ........................................................... 44
Wiring Diagram — SRS —/For Coupe ................... 13 INSTALLATION ................................................... 45
Wiring Diagram — SRS —/For Roadster ............... 19 SIDE CURTAIN AIR BAG MODULE (FOR COUPE)... 46
CONSULT-lll Function ............................................ 25 Removal and Installation ........................................ 46
DIAGNOSIS MODE FOR CONSULT-LLL ........... 25 REMOVAL ........................................................... 46
HOW TO CHANGE SELF-DIAGNOSIS MODE INSTALLATION ................................................... 47
WITH CONSULT-LII ............................................ 25 CRASH ZONE SENSOR ........................................... 48
HOW TO ERASE SELF-DIAGNOSTIC Removal and Installation ........................................ 48
RESULTS ............................................................ 26 REMOVAL ........................................................... 48
Self-Diagnosis Function (Without CONSULT-lll) ... 26 INSTALLATION ................................................... 48
HOW TO CHANGE SELF-DIAGNOSTIC MODE

Revision: 2006 November SRS-1 2007 350Z

SIDE AIR BAG (SATELLITE) SENSOR ................... 49 TROL UNIT ................................................................52
Removal and Installation ........................................ 49 Removal and Installation .........................................52
REMOVAL ........................................................... 49 COLLISION DIAGNOSIS ..........................................53
INSTALLATION .................................................... 49 For Frontal Collision ................................................53
FRONT SEAT BELT PRE-TENSIONER ................... 50 SRS INSPECTION (FOR FRONTAL COLLI-
Removal and Installation ........................................ 50 SION) ...................................................................53
DIAGNOSIS SENSOR UNIT ..................................... 51 For Side Collision ....................................................55
Removal and Installation ........................................ 51 WHEN THE SIDE AIR BAG IS ACTIVATED IN
REMOVAL ........................................................... 51 THE SIDE COLLISION: .......................................55
INSTALLATION .................................................... 51 WHEN SRS IS NOT ACTIVATED IN THE SIDE
ECU DISCRIMINATED NO. ................................. 51 COLLISION: .........................................................55
OCCUPANT CLASSIFICATION SYSTEM CON- SRS INSPECTION (FOR SIDE COLLISION) ......55

Revision: 2006 November SRS-2 2007 350Z

 PRECAUTIONS

PRECAUTIONS PFP:00001
A
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” NHS00008

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front C
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: D
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. E
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. F
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
G
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
NHS00009

● Do not use electrical test equipment to check SRS circuits unless instructed in this Service Manual. SRS
● Before servicing the SRS, turn ignition switch OFF, and disconnect both battery cables. Then wait at least
3 minutes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt I
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.
● Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformations or rust before J
installation and replace if required.
● The spiral cable must be set to the neutral position since its rotations are limited. Do not attempt to turn
steering wheel or column, if steering gear was disconnected from the column shaft. K
● Handle air bag module carefully. Always put a driver air bag module with the pad side facing upward.
● Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
L
● After an air bag deploymented, the front instrument panel assembly should be replaced if damaged.
● Always replace instrument panel pad following front passenger air bag deployment.
Precautions for Battery Service NHS0000A M
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Occupant Classification System Precaution NHS000A0

Replace occupant classification system control unit and passenger front seat cushion as an assembly.

Revision: 2006 November SRS-3 2007 350Z

 PREPARATION

PREPARATION PFP:00002

Commercial Service Tools NHS0000C

Tool name Description

Tamper resistant TORX bit Size: T30

S-NT757

Revision: 2006 November SRS-4 2007 350Z

 SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) PFP:28556

A
SRS Configuration NHS0000D

SRS

PHIA1120E

J
The air bag deploys if the diagnosis sensor unit activates while the ignition switch is in the ON or START posi-
tion.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module and front passenger air bag module are activated in a frontal col- K
lision but not in a side collision.
SRS configurations which are activated for some collision modes are as follows;
L
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module × — —
Front passenger air bag module × — — M
Front LH seat belt pre-tensioner × — —
Front RH seat belt pre-tensioner × — —
Front LH side air bag module — × —
Front RH side air bag module — — ×
LH side curtain air bag module* — × —
RH side curtain air bag module* — — ×
*: For Coupe

Revision: 2006 November SRS-5 2007 350Z

 SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Front Seat Belt Pre-tensioner with Load Limiter NHS0000E

The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger seat. It operates simul-
taneously with the SRS air bag system in the event of a frontal colli-
sion with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
SRS444
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.
Front Side Air Bag NHS0000F

Front side air bag is built-in type.

The front seatbacks with built-in type side air bag have the labels as
shown.

PHIA0158E

Side Curtain Air Bag/for Coupe NHS0000G

The side curtain air bags have the labels as shown.

PHIA0159E

Warning Lamp NHS000A6

Air bag warning lamp : (1)

Seat belt warning lamp: (2)

PHIA1358E

Revision: 2006 November SRS-6 2007 350Z

 SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Occupant Classification System (OCS) NHS000A1

A
The occupant classification system identifies different size occupants, out of position occupants, and detects if
child seat is present in the front passenger seat. The occupant classification system receives inputs from the
occupant classification sensor (located inside the passenger seat cushion assembly) and belt tension sensor
(part of the passenger front seat belt assembly and located at the belt anchor location). Depending on classifi- B
cation of passenger, the occupant classification system sends a signal to the diagnosis sensor unit. The diag-
nosis sensor unit uses this signal to determine full, partial, or non deployment of passenger front air bag in the
event of a collision. Depending on the signal received, the diagnosis sensor unit can disable the passenger C
front air bag completely.
NOTE:
In case of customer concern, CONSULT-ll can be used to confirm the passenger air bag status (readiness).
D
Passenger Air Bag Status Condition NHS000A2

Front Passenger Seat PASS AIR BAG OFF Indicator Passenger Air Bag Status
CONSULT-lll Display E
(Condition) (Status) (Readiness)
Seat occupied OFF Active (enabled) ON
seat occupiedNOTE ON Deactivated (disabled) OFF
F
Seat empty OFF Deactivated (disabled) OFF

NOTE:
Passenger does not meet Ocuupant classification System specifications for passenger air bag activation. G

Component Parts of Occupant Classification System NHS000A3

SRS

PHIA1357E
K
Occupant classification system con- Occupant classification system con-
1. 2. Seat sensor mat 3.
trol unit nector

4.
Passenger air bag OFF Indicator L
(cut-off telltaile)

Revision: 2006 November SRS-7 2007 350Z

 SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Passenger Seat belt Warning System NHS000A4

SYSTEM DESCRIPTION
This system warns when passenger seat belt is not fasten.

This system is composed of the following items.

● Seat belt warning lamp.
● Seat belt buckle switch (passenger side).
● Air bag diagnosis sensor unit.
● Occupant classification system.
Seat belt warning lamp is used for both driver seat belt warning and passenger seat belt warning.
Seat belt warning lamp turns ON when all conditions below are met.
● Driver seat belt is fastened.
● Occupant is on passenger seat.
● Passenger seat belt is not fasten.

Revision: 2006 November SRS-8 2007 350Z

 TROUBLE DIAGNOSIS

TROUBLE DIAGNOSIS PFP:00004

A
Trouble Diagnosis Introduction NHS0000H

CAUTION:
● Do not use electrical test equipment on any circuit related to the SRS unless instructed in this Ser- B
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
● Do not repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a C
new one.
● Keep ground portion clean.
DIAGNOSIS FUNCTION D
The SRS self-diagnostic results can be read by using “AIR BAG” warning lamp and/or CONSULT-lll.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp. E
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-IlI are as follows:
User mode Diagnosis mode Display type F
“AIR BAG” warning lamp X X ON-OFF operation
CONSULT-lII — X Monitoring
G
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
SRS
toms or conditions for a customer complaint.
Information from Customer
WHAT..... Vehicle model I
WHEN..... Date, Frequencies
WHERE..... Road conditions
HOW..... Operating conditions, Symptoms
J
Preliminary Check
Make sure that the following parts are in good order.
● Battery (Refer to SC-4, "How to Handle Battery" .) K
● Fuse (Refer to SRS-13, "Wiring Diagram — SRS —/For Coupe" or SRS-19, "Wiring Diagram — SRS —/
For Roadster" .)
● System component-to-harness connections L

Revision: 2006 November SRS-9 2007 350Z

 TROUBLE DIAGNOSIS

WORK FLOW

PHIA1363E

*1: SRS-9, "Preliminary Check". *2: SRS-27, "SRS Operation Check *3: SRS-29, "Trouble Diagnosis with
(USER MODE)". CONSULT-IlI".
*4: SRS-33, "Trouble Diagnosis without
CONSULT-IlI".

Revision: 2006 November SRS-10 2007 350Z

 TROUBLE DIAGNOSIS

Component Parts Location NHS0000I

SRS

J
PHIA1356E

1. Driver air bag module 2. Front passenger air bag module 3. Spiral cable
Side air bag (Satellite) sensor (LH/ K
4. Front side air bag module (LH/RH) 5. Diagnosis sensor unit 6.
RH)
7. Seat belt pre-tensioner (LH/RH) 8. Seat belt buckle switch (LH/ RH) 9. Side curtain air bag module*
Occupant classification system con- L
10. Crash zone sensor 11. 12. Seat sensor mat
trol unit
Occupant classification system con-
13.
nector
M
*: For Coupe

Revision: 2006 November SRS-11 2007 350Z

 TROUBLE DIAGNOSIS

Schematic NHS0000J

THWT0270E

Revision: 2006 November SRS-12 2007 350Z

 TROUBLE DIAGNOSIS

Wiring Diagram — SRS —/For Coupe NHS0000K

SRS

THWT0271E

Revision: 2006 November SRS-13 2007 350Z

 TROUBLE DIAGNOSIS

THWT0258E

Revision: 2006 November SRS-14 2007 350Z

 TROUBLE DIAGNOSIS

SRS

THWT0165E

Revision: 2006 November SRS-15 2007 350Z

 TROUBLE DIAGNOSIS

THWT0259E

Revision: 2006 November SRS-16 2007 350Z

 TROUBLE DIAGNOSIS

SRS

THWT0272E

Revision: 2006 November SRS-17 2007 350Z

 TROUBLE DIAGNOSIS

THWT0273E

Revision: 2006 November SRS-18 2007 350Z

 TROUBLE DIAGNOSIS

Wiring Diagram — SRS —/For Roadster NHS0000L

SRS

THWT0274E

Revision: 2006 November SRS-19 2007 350Z

 TROUBLE DIAGNOSIS

THWT0275E

Revision: 2006 November SRS-20 2007 350Z

 TROUBLE DIAGNOSIS

SRS

THWT0276E

Revision: 2006 November SRS-21 2007 350Z

 TROUBLE DIAGNOSIS

THWT0277E

Revision: 2006 November SRS-22 2007 350Z

 TROUBLE DIAGNOSIS

SRS

THWT0278E

Revision: 2006 November SRS-23 2007 350Z

 TROUBLE DIAGNOSIS

THWT0279E

Revision: 2006 November SRS-24 2007 350Z

 TROUBLE DIAGNOSIS

CONSULT-lll Function NHS0000M

DIAGNOSIS MODE FOR CONSULT-LLL A

● “SELF-DIAG [CURRENT]”
A current self-diagnostic results (also indicated by the number of warning lamp flashes in the Diagnosis
mode) is displayed on the CONSULT-lll screen in real time. This refers to a malfunctioning part requiring B
repairs.
● “SELF-DIAG [PAST]”
Self-diagnostic results previously stored in the memory are displayed on the CONSULT-lll screen. The C
stored results are not erased until memory erasing is performed.
● “TROUBLE DIAG RECORD”
With TROUBLE DIAG RECORD, diagnostic results previously erased by a reset operation can be dis-
D
played on the CONSULT-lll screen.
● “ECU DISCRIMINATED NO.”
The diagnosis sensor unit for each vehicle model is assigned with its own, individual classification num-
ber. This number will be displayed on the CONSULT-lll screen, as shown. When replacing the diagnosis E
sensor unit, refer to the part number for the compatibility. After installation, replacement with a correct unit
can be checked by confirming this classification number on the CONSULT-lll screen.
After repair, make sure the discriminated number of diagnosis sensor unit installed to vehicle are same. F
Refer to SRS-51, "ECU DISCRIMINATED NO." .
HOW TO CHANGE SELF-DIAGNOSIS MODE WITH CONSULT-LII
From User Mode to Diagnosis Mode G
After selecting “AIR BAG” on the “SELECT SYSTEM” screen, User mode automatically changes to Diagnosis
mode.
SRS
From Diagnosis Mode to User Mode
To return to User mode from Diagnosis mode, touch “BACK” key of CONSULT-lll until “SELECT SYSTEM”
appears, then diagnosis mode automatically changes to User mode.
I

Revision: 2006 November SRS-25 2007 350Z

 TROUBLE DIAGNOSIS

HOW TO ERASE SELF-DIAGNOSTIC RESULTS

● “SELF-DIAG [CURRENT]”
A current self-diagnostic result is displayed on the CONSULT-lll screen in real time.
After the malfunction is repaired completely, no malfunction is detected on “SELF-DIAG [CURRENT]”.
● “SELF-DIAG [PAST]”
Return to the “SELF-DIAG [CURRENT]” CONSULT-lll screen by touching “BACK” key of CONSULT-lll and
select “SELF-DIAG [CURRENT]” in SELECT DIAG MODE. Touch “ERASE” in “SELF-DIAG [CURRENT]”
mode.
NOTE:
If the memory of the malfunction in “SELF-DIAG [PAST]” is not erased, the User mode shows the system
malfunction by the operation of the warning lamp even if the malfunction is repaired completely.
● “TROUBLE DIAG RECORD”
The memory of “TROUBLE DIAG RECORD” cannot be erased.
Self-Diagnosis Function (Without CONSULT-lll) NHS0000N

● The reading of these results is accomplished “User mode” and “Diagnosis mode”.
● After a malfunction is repaired, turn ignition switch ON. Diagnosis mode returns to the User mode. At that
time, the self-diagnostic result is cleared.
HOW TO CHANGE SELF-DIAGNOSTIC MODE WITHOUT CONSULT-LLL

PHIA0709E

HOW TO ERASE SELF-DIAGNOSTIC RESULTS

After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis
mode returns to the User mode. At that time, the self-diagnostic results are cleared.

Revision: 2006 November SRS-26 2007 350Z

 TROUBLE DIAGNOSIS

SRS Operation Check (USER MODE) NHS0000O

DIAGNOSTIC PROCEDURE A
Checking Air Bag Operation by Using “AIR BAG” Warning Lamp—User Mode
1. Turn ignition switch from OFF to ON, and make sure that the air bag warning lamp blinks.
2. Compare the SRS air bag warning lamp blinking pattern with the B
examples.

E
BF-1845D

SRS

Revision: 2006 November SRS-27 2007 350Z

 TROUBLE DIAGNOSIS

Warning lamp examples

“AIR BAG” warning lamp operation-User mode- SRS condition Reference item

● No malfunction is detected.
—
● No further action is necessary.

SHIA0011E

Go to SRS-33, "WARNING LAMP

FLASH CODE CHART" or SRS-29,
● The system is malfunctioning and
"DTC No. Index (“SELF-DIAG
needs to be repaired as indicated.
[CURRENT]” “SELF-DIAG [PAST]”
or TROUBLE DIAG RECORD )" .

SHIA0012E

● Air bag is deployed. Go to SRS-53, "COLLISION DIAG-

● Seat belt pre-tensioner is deployed. NOSIS" .

● Diagnosis sensor unit is malfunction-

ing.
Go to SRS-37, "Trouble Diagnosis:
● Air bag power supply circuit is mal-
“AIR BAG” Warning Lamp Does Not
functioning.
Turn OFF" .
● SRS air bag warning lamp circuit is
malfunctioning.
SHIA0013E

● Diagnosis sensor unit is malfunction-

ing. Go to SRS-38, "Trouble Diagnosis:
“AIR BAG” Warning Lamp Does Not
● Air bag warning lamp circuit is mal- Turn ON" .
functioning.

SHIA0014E

Revision: 2006 November SRS-28 2007 350Z

 TROUBLE DIAGNOSIS

Trouble Diagnosis with CONSULT-IlI NHS0000P

DIAGNOSTIC PROCEDURE A

Diagnositic mode Description

The self-diagnosis result is displayed. (SELF-DIAG [CURRENT], [PAST], [RECORRD]). B
SELF-DIAG RESULT Refer to SRS-29, "DTC No. Index (“SELF-DIAG [CURRENT]” “SELF-DIAG [PAST]” or
TROUBLE DIAG RECORD )" .
ECU DISCRIMINATED No. The parts number of diagnosis sensor unit is displayed.
C
DTC No. Index (“SELF-DIAG [CURRENT]” “SELF-DIAG [PAST]” or TROUBLE DIAG RECORD )
Repair order
Diagnostic item Explanation D
“Recheck SRS at each replacement”
NO DTC IS DETECTED. When malfunction is ● Low battery voltage (Less than 9V) —
indicated by the “AIR
● Self-diagnostic results “SELF-DIAG ● Go to SRS-25, "DIAGNOSIS MODE E
BAG” warning lamp in
[PAST]” (previously stored in the FOR CONSULT-lll" .
User mode.
memory) might not be erased after
repair.
● Intermittent malfunction has been F
detected in the past.
● No malfunction is detected. —
G
DRIVER AIRBAG MOD- ● Driver air bag module circuit is open (including the spiral 1. Visually check the wiring harness
ULE cable). connection.
[OPEN] 2. Replace the harness if it has visible
[B1054] SRS
damage.
DRIVER AIRBAG MOD- ● Driver air bag module circuit is shorted to a power supply cir- 3. Replace driver air bag module.
ULE cuit (including the spiral cable).
[VB-SHORT] 4. Replace the spiral cable.
[B1055] 5. Replace the diagnosis sensor unit.
I

DRIVER AIRBAG MOD- ● Driver air bag module circuit is shorted to ground (including the
ULE spiral cable).
[GND-SHORT] J
[B1056]
DRIVER AIRBAG MOD- ● Driver air bag module circuit is shorted between lines.
ULE K
[SHORT]
[B1057]
ASSIST A/B MODULE ● Front passenger air bag module circuit is shorted to a power 1. Visually check the wiring harness
L
[VB-SHORT] supply circuit. connection.
[B1070] 2. Replace the harness if it has visible
ASSIST A/B MODULE ● Front passenger air bag module circuit is open. damage.
[OPEN] M
3. Replace front passenger air bag
[B1071] module.
ASSIST A/B MODULE ● Front passenger air bag module circuit is shorted to ground. 4. Replace the diagnosis sensor unit.
[GND-SHORT]
[B1072]
ASSIST A/B MODULE ● Front passenger air bag module circuit is shorted between
[SHORT] lines.
[B1073]
CRASH ZONE SEN ● Crash zone sensor 1. Visually check the wiring harness
[UNIT FAIL] connection.
[B1033] 2. Replace the harness if it has visible
[B1034]
damage.
CRASH ZONE SEN
[COMM FAIL] 3. Replace the crash zone sensor.
[B1035] 4. Replace the diagnosis sensor unit.
CRASH ZONE SEN
[UNMATCH]
[B1036]

Revision: 2006 November SRS-29 2007 350Z

 TROUBLE DIAGNOSIS

Repair order
Diagnostic item Explanation
“Recheck SRS at each replacement”
SIDE MODULE LH ● Front LH side air bag module circuit is open. 1. Visually check the wiring harness
[OPEN] connection.
[B1134] 2. Replace the harness if it has visible
SIDE MODULE LH ● Front LH side air bag module circuit is shorted to a power sup- damage.
[VB-SHORT] ply circuit. 3. Replace front LH setback assembly
[B1135] (front LH side air bag module).
SIDE MODULE LH ● Front LH side air bag module circuit is shorted to ground. 4. Replace the diagnosis sensor unit.
[GND-SHORT]
[B1136]
SIDE MODULE LH ● Front LH side air bag module circuit is shorted between lines.
[SHORT]
[B1137]
SIDE MODULE RH ● Front RH side air bag module circuit is open. 1. Visually check the wiring harness
[OPEN] connection.
[B1129] 2. Replace the harness if it has visible
SIDE MODULE RH ● Front RH side air bag module circuit is shorted to some power damage.
[VB-SHORT] supply circuit. 3. Replace front RH setback assembly
[B1130] (front RH side air bag module).
SIDE MODULE RH ● Front RH side air bag module circuit is shorted to ground. 4. Replace the diagnosis sensor unit.
[GND-SHORT]
[B1131]
SIDE MODULE RH ● Front RH side air bag module circuit is shorted between lines.
[SHORT]
[B1132]
SATELLITE SENS LH ● LH side air bag (Satellite) sensor 1. Visually check the wiring harness
[UNIT FAIL] connection.
[B1118] 2. Replace the harness if it has visible
[B1119]
damage.
SATELLITE SENS LH
[COMM FAIL] 3. Replace the LH side air bag (Satel-
[B1120] lite) sensor.
SATELLITE SENS LH 4. Replace the diagnosis sensor unit.
[UNMATCH]
[B1121]
SATELLITE SENS RH ● RH side air bag (Satellite) sensor 1. Visually check the wiring harness
[UNIT FAIL] connection.
[B1113] 2. Replace the harness if it has visible
[B1114]
damage.
SATELLITE SENS RH
[COMM FAIL] 3. Replace the RH side air bag (Satel-
[B1115] lite) sensor.
SATELLITE SENS RH 4. Replace the diagnosis sensor unit.
[UNMATCH]
[B1116]
PRE-TEN FRONT LH ● Front LH pre-tensioner circuit is open. 1. Visually check the wiring harness
[OPEN] connections.
[B1086] 2. Replace the harness if it has visible
PRE-TEN FRONT LH ● Front LH pre-tensioner circuit is shorted to a power supply cir- damage.
[VB-SHORT] cuit. 3. Replace front LH seat belt.
[B1087]
4. Replace the diagnosis sensor unit.
PRE-TEN FRONT LH ● Front LH pre-tensioner circuit is shorted to ground.
[GND-SHORT]
[B1088]
PRE-TEN FRONT LH ● Front LH pre-tensioner circuit is shorted between lines.
[SHORT]
[B1089]

Revision: 2006 November SRS-30 2007 350Z

 TROUBLE DIAGNOSIS

Repair order
Diagnostic item Explanation
“Recheck SRS at each replacement” A
PRE-TEN FRONT RH ● Front RH pre-tensioner circuit is shorted to a power supply cir- 1. Visually check the wiring harness
[OPEN] cuit. connections.
[B1081] 2. Replace the harness if it has visible B
PRE-TEN FRONT RH ● Front RH pre-tensioner is shorted to a power supply circuit. damage.
[VB-SHORT] 3. Replace front RH seat belt.
[B1082]
4. Replace the diagnosis sensor unit. C
PRE-TEN FRONT RH ● Front RH pre-tensioner circuit is shorted to ground.
[GND-SHORT]
[B1083]
D
PRE-TEN FRONT RH ● Front RH pre-tensioner circuit is shorted between lines.
[SHORT]
[B1084]
CURTAIN MODULE LH* ● LH side curtain air bag module circuit is open. 1. Visually check the wiring harness E
[OPEN] connection.
[B1150] 2. Replace the harness if it has visible
CURTAIN MODULE LH* damage. F
● LH side curtain air bag module circuit is shorted to some power
[VB-SHORT] 3. Replace LH side curtain air bag
supply circuits.
[B1151] module.
CURTAIN MODULE LH* ● LH side curtain air bag module circuit is shorted to ground. 4. Replace the diagnosis sensor unit. G
[GND-SHORT]
[B1152]
CURTAIN MODULE LH* ● LH side curtain air bag module circuit is shorted between lines.
[SHORT] SRS
[B1153]
CURTAIN MODULE RH* ● RH side curtain air bag module circuit is open. 1. Visually check the wiring harness
[OPEN] connection. I
[B1145] 2. Replace the harness if it has visible
CURTAIN MODULE RH* damage.
● RH side curtain air bag module circuit is shorted to a power
[VB-SHORT] 3. Replace RH side curtain air bag J
supply circuit.
[B1146] module.
CURTAIN MODULE RH* ● RH side curtain air bag module circuit is shorted to ground. 4. Replace the diagnosis sensor unit.
[GND-SHORT]
[B1147]
K

CURTAIN MODULE RH* ● RH side curtain air bag module circuit is shorted between lines.
[SHORT]
[B1148] L
CONTROL UNIT ● Diagnosis sensor unit is malfunctioning. ● Replace the diagnosis sensor unit.
[B1001-B1015]
[B1026-B1031] M
[B1042-B1047]
[B1058-B1063]
[B1074-B1079]
[B1106-B1111]
[B1122-B1127]
[B1138-B1143]
[B1202-B1207]
PASS A/B INDCTR CKT ● Cutoff telltale circuit is open or shorted to grand or the circuits 1. Visually check the wiring harness
[B1023] are shorted each other. connection.
2. Replace the harness if it has visible
damage.
3. Replace cutoff telltale.
4. Replace the diagnosis sensor unit.

Revision: 2006 November SRS-31 2007 350Z

 TROUBLE DIAGNOSIS

Repair order
Diagnostic item Explanation
“Recheck SRS at each replacement”
OCCUPANT SENS C/U ● Trouble occurs in Occupant Classification System-CU. ● Replace passenger side seat cush-
[UNIT FAIL] ion assembly.
[B1017]
[B1020]
[B1021]
OCCUPANT SENS C/U ● Trouble occurs in Occupant Classification System-CU, circuit 1. Visually check the wiring harness
[COMM FAIL] of Occupant Classification System-CU—Diagnosis Sensor Unit connection.
[B1022] or Diagnosis Sensor Unit. 2. Replace the harness if it has visible
damage.
3. Replace passenger side seat cush-
ion assembly.
4. Replace the diagnosis sensor unit.
OCCUPANT SENS ● Trouble occurs in Occupant Classification System-SENS. ● Replace passenger side seat cush-
[UNIT FAIL] ion assembly.
[B1018]
FRONTAL COLLISION ● Seat belt pre-tensioner and front air bag are deployed. ● Go to SRS-53, "For Frontal Colli-
DETECTION sion" .
[B1209]
SIDE COLLISION ● Side and curtain air bag is deployed. ● Go to SRS-55, "For Side Collision" .
DETECTION
[B1210]
*: For coupe
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp or CONSULT-IlI each time repair is finished. If malfunction is still
observed, proceed to the next step. When malfunction is eliminated, further repair work is not required.

Revision: 2006 November SRS-32 2007 350Z

 TROUBLE DIAGNOSIS

Trouble Diagnosis without CONSULT-IlI NHS0000Q

DIAGNOSTIC PROCEDURE A
Inspecting SRS Malfunctioning Parts by Using “AIR BAG” Warning Lamp — Diagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode. B
1. Turn ignition switch ON.
2. After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
C
3. Wait more than 3 seconds.
4. Repeat the steps 1 to 3 two times.
5. Turn ignition switch ON. D
SRS is now in Diagnosis mode.
“AIR BAG” warning lamp operates in Diagnosis mode as follows:
WARNING LAMP FLASH CODE CHART E

SRS
PHIA0532E

PHIA1233E
L

SHIA0028E

Revision: 2006 November SRS-33 2007 350Z

 TROUBLE DIAGNOSIS

PHIA1234E

SHIA0083E

PHIA1235E

PHIA1236E

Revision: 2006 November SRS-34 2007 350Z

 TROUBLE DIAGNOSIS

SHIA0032E
D

G
SHIA0033E

SRS

K
PHIA1237E

PHIA1238E

Revision: 2006 November SRS-35 2007 350Z

 TROUBLE DIAGNOSIS

PHIA1240E

PHIA1241E

PHIA1242E

PHIA1243E

Revision: 2006 November SRS-36 2007 350Z

 TROUBLE DIAGNOSIS

Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn OFF NHS0000R

DIAGNOSTIC PROCEDURE A

1. CHECK THE DEPLOYMENT OF AIR BAG MODULE

Is air bag module deployed? B
YES or NO
YES >> Refer to SRS-53, "COLLISION DIAGNOSIS" .
NO >> GO TO 2. C

2. CHECK THE AIR BAG FUSE

D
Check 10A fuse [No.13, located in fuse block (J/B)].
Refer to PG-15, "Fuse" .
OK or NG
E
OK >> GO TO 4.
NG >> GO TO 3.

3. CHECK AIR BAG FUSE AGAIN F

Replace “AIR BAG” fuse and turn ignition switch ON.

Does the “AIR BAG” fuse blow again? G
YES >> Repair or replace main harness.
NO >> INSPECTION END
SRS
4. CHECK DIAGNOSIS SENSOR UNIT
With CONSULT-IlI
Is “AIR BAG” displayed on CONSULT-IlI? I
YES or NO
YES >> GO TO 5.
NO >> Visually check the wiring harness connection of diagnosis sensor unit. If the harness connection J
check result is OK, replace diagnosis sensor unit.

5. CHECK HARNESS CONNECTION K

Is harness connection between warning lamp and diagnosis sensor unit OK?
OK or NG L
OK >> Replace diagnosis sensor unit.
NG >> Connect “AIR BAG” warning lamp and diagnosis sensor unit connector properly. If “AIR BAG”
warning lamp still does not go off, replace harness.
M

Revision: 2006 November SRS-37 2007 350Z

 TROUBLE DIAGNOSIS

Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn ON NHS0000S

DIAGNOSTIC PROCEDURE
1. CHECK “METER” FUSE
Check 10A fuse [No.14, located in fuse block (J/B)].
Refer to PG-15, "Fuse" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.

2. CHECK “METER” FUSE AGAIN

Replace 10A fuse [No.14, located in fuse block (J/B)] and turn ignition switch ON.
Does the meter fuse blow again?
YES >> Repair or replace the related harness.
NO >> INSPECTION END

3. CHECK HARNESS CONNECTION BETWEEN DIAGNOSIS SENSOR UNIT AND COMBINATION

METER
Disconnect diagnosis sensor unit connector and turn ignition switch ON.
Does “AIR BAG” warning lamp turn ON?
YES or NO
YES >> Replace diagnosis sensor unit.
NO >> Replace combination meter assembly.

Revision: 2006 November SRS-38 2007 350Z

 TROUBLE DIAGNOSIS

Trouble Diagnosis: Passenger Seat belt Warning System NHS000A5

1. HECK THE SYSTEM 1 A

Check seat belt warning lamp function.

B
Seat belt warning lamp turns ON in the following conditions.
● Driver seat belt is fastened.
● Occupant is on passenger seat. C
● Passenger seat belt is not fasten.
D
OK or NG
OK >> GO TO 2.
NG >> Check the followings.
E
● Harness between air bag diagnosis sensor unit and combination meter.

● Seat belt buckle switch (passenger side) circuit.

● Seat belt buckle switch (passenger side).

F
If these are OK, replace air bag diagnosis sensor unit.

2. CHECK THE SYSTEM 2 G

Check seat belt warning lamp function.

SRS
Seat belt warning lamp turns OFF in the following conditions.
● Driver seat belt is fastened.
● Occupant is on passenger seat. I
● Passenger seat belt is fastened.

OK or NG J
OK >> System is OK.
NG >> Check the followings.
● Sea tbelt buckle switch (passenger side) circuit. K
● Seat belt buckle switch (passenger side).
If these are OK, replace air bag diagnosis sensor unit.
L

Revision: 2006 November SRS-39 2007 350Z

 DRIVER AIR BAG MODULE

DRIVER AIR BAG MODULE PFP:K8510

Removal and Installation NHS0000T

PHIA0715E

1. Driver air bag module 2. Side lid (RH/LH) 3. Steering wheel

4. TORX bolt (T30)

REMOVAL
CAUTION:
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Always work from the side of driver air bag module.
● Do not use air tools or electric tools for servicing.
1. Remove the side lids (RH/LH).
2. Using Tamper resistant TORX bit (T30), remove the TORX bolts
(T30) at right and left.

PHIA0714E

3. Disconnect the steering wheel switch sub-harness connector.

4. Disconnect the air bag harness connector, and remove the
driver air bag module.
CAUTION:
● For installing / removing driver air bag module connector,
insert thin screwdriver wrapped in tape into notch, lift
lock and remove connector.
● Install connector with lock raised, and push lock into
connector.
● After installing the connector, make sure that the lock is
pushed securely into it.
PHIA0308E

Revision: 2006 November SRS-40 2007 350Z

 DRIVER AIR BAG MODULE

CAUTION:
● Always work from the side of driver air bag module. A
● Always place driver air bag module with pad side facing
upward.
● Do not insert any foreign objects (screwdriver, etc.) into B
driver air bag module.
● Do not disassemble driver air bag module.
● Do not use old bolts after removal; replace with new bolts. C
● Do not expose the driver air bag module to temperatures
exceeding 90°C (194°F).
PHIA0164E D

● Replace driver air bag module if it has been dropped or sus-

tained an impact.
E
● Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
F

SBF814E

INSTALLATION SRS
Install in the reverse order of removal.
CAUTION:
● For installing the air bag module, tighten the TORX bolts (T30). I
● After the work is completed, perform self-diagnosis to make sure that no malfunction is detected.
Refer to SRS-27, "SRS Operation Check (USER MODE)" .
J

Revision: 2006 November SRS-41 2007 350Z

 SPIRAL CABLE

SPIRAL CABLE PFP:25554

Removal and Installation NHS0000U

PHIA1255E

1. Steering wheel 2. Driver air bag module connector 3. Spiral cable

4. Screw (Do not remove) 5. Wiper and washer switch 6. Screw
7. Sreering column assembly 8. Combination meter 9. Lighting and turn signal switch

REMOVAL
CAUTION:
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Do not use air tools or electric tools for servicing.
1. Remove driver air bag module. Refer to SRS-40, "Removal and Installation" .
2. Disconnect horn switch connector.
3. Set the steering wheel in the neutral position.
4. Remove steering wheel. Refer to PS-7, "STEERING WHEEL" .
5. Remove combination meter assembly. Refer to DI-24, "Removal and Installation for Combination Meter" .
6. Loosen the spiral cable fixing screws, and then remove the spiral cable.
CAUTION:
● Do not disassemble spiral cable.

● Do not apply lubricant to the spiral cable.

7. Remove the horn switch connector and then remove spiral cable
connector.
CAUTION:
Also, with the steering linkage disconnected the cable may
snap by turning the steering wheel beyond the limited num-
ber of turns.

SHIA0193E

Revision: 2006 November SRS-42 2007 350Z

 SPIRAL CABLE

INSTALLATION
Install in the reverse order of removal. A
CAUTION:
● The spiral cable may snap by steering operation if the cable
is installed in an improper position. B
● The neutral position is set as follows.
Turn quietly the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and harf turns) and C
stop turning at the point on which the stopper insertion
holes are in the same position.
The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper D
is removed.
● Do not turn the spiral cable rashly and also beyond the limit
number of turns. (These will cause cable snap.) E
● Adjust the spiral cable locating pin (showed as A inthe fig-
ure) to the steering wheel locating pin hole (showed as C in
the figuer). F
● Secure the air bag harness with the harness fixing hook.
● After the work is completed, make sure no system malfunc-
tion is detected by air bag warning lamp. G
● In case that malfunction is detected by the air bag warning
lamp, reset by the self-diagnosis function and delete the
memory by CONSULT−IlI. SRS
● In case that malfunction is still detected after the above PHIA0887J

operation, perform self-diagnosis to repair malfunctions.

Refer to Refer to SRS-27, "SRS Operation Check (USER MODE)" . I

Revision: 2006 November SRS-43 2007 350Z

 FRONT PASSENGER AIR BAG MODULE

FRONT PASSENGER AIR BAG MODULE PFP:K8515

Removal and Installation NHS0000V

REMOVAL
CAUTION:
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Always work from the side of or under front passenger air bag module.
● Do not use air tools or electric tools for servicing.
1. Remove cluster lid C. Refer to IP-14, "(Q) Cluster Lid C" .
2. Remove instrument passenger panel lower and knee protector (RH). Refer to IP-13, "(L) Instrument Pas-
senger Panel Lower" .
3. Disconnect passenger air bag module connector.
Passenger air bag module connector : (1)
4. Remove hexagon bolt, and then remove instrument passenger
panel upper assembly.

PHIA1247E

5. Remove fixing nuts, and then remove front passenger air bag
module.

PHIA1248E

CAUTION:
● Always place front passenger air bag module with caution label side facing upward.
● Do not insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
● Do not disassemble front passenger air bag module.
● Do not use old bolts after removal; replace with new bolts.

● Replace front passenger air bag module if it has been

dropped or sustained an impact.
● Do not expose the front passenger air bag module to tem-
peratures exceeding 90°C (194°F).
● Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
● After front passenger air bag module inflates, the instru-
ment panel assembly should be replaced.

SBF814E

Revision: 2006 November SRS-44 2007 350Z

 FRONT PASSENGER AIR BAG MODULE

INSTALLATION
Install in the reverse order of removal. A
CAUTION:
● Always work from the side of or under front passenger air bag module.
● After the work is completed, perform self-diagnosis to make sure that no malfunction is detected. B
Refer to SRS-27, "SRS Operation Check (USER MODE)" .

SRS

Revision: 2006 November SRS-45 2007 350Z

 SIDE CURTAIN AIR BAG MODULE (FOR COUPE)

SIDE CURTAIN AIR BAG MODULE (FOR COUPE) PFP:985P0

Removal and Installation NHS0000W

PHIA0660E

1. Side curtain air bag module 2. Clip 3. Bolt

REMOVAL
CAUTION:
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Do not use air tools or electric tools for servicing.
1. Remove headlining. Refer to EI-44, "Removal and Installation (for Coupe Models)" .
2. Disconnect side curtain air bag connector.
3. Remove side curtain air bag module fixing bolts and clip.
4. Remove the side curtain air bag module.
CAUTION:
● Always place the side curtain air bag module with the
warning label facing upward.
● Do not disassemble side curtain air bag module.

● Do not insert any foreign objects (screwdriver, etc.) into

air bag module connector.

PHIA0171E

● Replace side curtain air bag module if it has been

dropped or sustained an impact.
● Do not expose the air bag module to temperatures
exceeding 90°C (194°F).
● Do not allow oil, grease or water to come in contact with
the side curtain air bag module.

SBF814E

Revision: 2006 November SRS-46 2007 350Z

 SIDE CURTAIN AIR BAG MODULE (FOR COUPE)

INSTALLATION
Install in the reverse order of removal. A
CAUTION:
● Always work from the side of the side curtain air bag module.
● After replacement of side curtain air bag module, perform self-diagnosis to make sure that no mal- B
function is detected. Refer to SRS-27, "SRS Operation Check (USER MODE)" .

SRS

Revision: 2006 November SRS-47 2007 350Z

 CRASH ZONE SENSOR

CRASH ZONE SENSOR PFP:98531

Removal and Installation NHS0000X

REMOVAL
CAUTION:
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Do not use air tools or electric tools for servicing.
1. Remove crash zone sensor connector.
2. Remove crash zone sensor fixing nuts.

PHIA0172E

CAUTION:
● Replace crash zone sensor if it has been dropped or sustained an impact.
● Do not disassemble crash zone sensor.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
● Check crash zone sensor for proper installation.
● After the work is complete, perform self-diagnosis to make sure that no malfunction is detected.
Refer to SRS-27, "SRS Operation Check (USER MODE)" .

Revision: 2006 November SRS-48 2007 350Z

 SIDE AIR BAG (SATELLITE) SENSOR

SIDE AIR BAG (SATELLITE) SENSOR PFP:98830

A
Removal and Installation NHS0000Y

REMOVAL
CAUTION: B
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Do not use air tools or electric tools for servicing.
C
1. Remove seat belt pre-tensioner. Refer to SB-4, "Removal and Installation of Seat Belt (Coupe)" or SB-6,
"Removal and Installation of Seat Belt (Roadster)" .
2. Remove side air bag (Satellite) sensor fixing nuts.
D
3. Remove the side air bag (Satellite) sensor connector.

PHIA0176E
G
CAUTION:
● Do not use old nuts; replace with new ones.
● Check side air bag (Satellite) sensor to ensure it is free of deformities, dents, cracks or rust. If it SRS
shows any visible signs of damage, replace it with new one.
● Do not attempt to disassemble side air bag (Satellite) sensor.
● Replace side air bag (Satellite) sensor if it has been dropped or sustained an impact. I

INSTALLATION
Install in the reverse order of removal. J
CAUTION:
● Check side air bag (Satellite) sensor for proper installation.
● After replacement of side air bag (Satellite) sensor, perform self-diagnosis to make sure that no K
malfunction is detected. Refer to SRS-27, "SRS Operation Check (USER MODE)" .

Revision: 2006 November SRS-49 2007 350Z

 FRONT SEAT BELT PRE-TENSIONER

FRONT SEAT BELT PRE-TENSIONER PFP:86884

Removal and Installation NHS0000Z

For removal and installation procedures, refer to SB-4, "Removal and Installation of Seat Belt (Coupe)" or SB-
6, "Removal and Installation of Seat Belt (Roadster)" .

Revision: 2006 November SRS-50 2007 350Z

 DIAGNOSIS SENSOR UNIT

DIAGNOSIS SENSOR UNIT PFP:28556

A
Removal and Installation NHS00010

REMOVAL
CAUTION: B
● Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
● Do not use air tools or electric tools for servicing.
C
1. Disconnect each harness connector for the air bag module and seat belt pre-tensioner.
2. Remove center console. Refer to IP-11, "Removal and Installation" .
3. Disconnect diagnosis sensor unit connector. D
4. Remove fixing bolts from the diagnosis sensor unit.

Hex bolt: 24.5 N·m (2.5 kg-m, 18 ft-lb)

E
Ground bolt: 6.9 N·m (0.7 kg-m, 61 in-lb)

PHIA0463E G

CAUTION:
● Do not use old bolts. Replace with new ones.
SRS
● Check diagnosis sensor unit bracket to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace with new one.
● Replace diagnosis sensor unit if it has been dropped or sustained an impact.
I
INSTALLATION
Install in the reverse order of removal.
CAUTION: J
● Check the diagnosis sensor unit for proper installation.
● After replacement of diagnosis sensor unit, perform self-diagnosis to make sure that no malfunc-
tion is detected. Refer to SRS-27, "SRS Operation Check (USER MODE)" . K
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, make sure that the diagnosis sensor unit identification is correct for
L
the vehicle as equipped.
Model Specification ECU DISCRIMINATED No.
Models with driver and passenger air bags and seat belt pre-tensioner FAE6 M
Coupe Models with driver and passenger air bags, seat belt pre-tensioner, side air bags and curtain
FAE4
air bags
Models with driver and passenger air bags and seat belt pre-tensioner FAE7
Roadster
Models with driver and passenger air bags, seat belt pre-tensioner and side air bags FAE5

Revision: 2006 November SRS-51 2007 350Z

 OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT PFP:98852

Removal and Installation NHS000A7

The occupant classification system control unit, seat pressure sensor, and bladder are an integral part of the
front passenger seat cushion and are replaced as an assembly. Refer to SE-67, "Removal and Installation" .

Revision: 2006 November SRS-52 2007 350Z

 COLLISION DIAGNOSIS

COLLISION DIAGNOSIS PFP:00015

A
For Frontal Collision NHS00011

To repair the SRS, perform the following steps.

When SRS (except the front side air bag and side curtain air bag modules) is activated in a collision: B
1. Replace the diagnosis sensor unit.
2. Remove the air bag modules (except the front side air bag modules and side curtain air bag modules),
crash zone sensor assembly, bracket and seat belt pre-tensioner assemblies. C
3. Check the SRS components using the table below:
– Replace any SRS components showing visible signs of damage (dents, cracks and deformation).
4. Install new air bag modules (except the front side air bag modules and side curtain air bag modules) crash D
zone sensor assembly, bracket and seat belt pre-tensioner assemblies.
5. Perform self-diagnosis using CONSULT-IlI or “AIR BAG” warning lamp. Refer to SRS-27, "SRS Operation
Check (USER MODE)" for details. Ensure entire SRS operates properly. E
When SRS is not activated in a collision:
1. Check the SRS components using the table below:
– Replace any SRS components showing visible signs of damage (dents, cracks and deformation). F
2. Perform self-diagnosis using CONSULT-IlI or “AIR BAG” warning lamp. Refer to SRS-27, "SRS Operation
Check (USER MODE)" for details. Ensure entire SRS operates properly.
When only one front air bag module is activated in a collision: G
1. Replace the following components:
– Diagnosis sensor unit
SRS
– Crash zone sensor
– Activated front air bag and seat belt pre-tensioner.
2. Check the other SRS components using the table below. (Refer to “SRS is NOT activated”.) I
– Replace any SRS components showing visible signs of damage (dents, cracks and deformation).
3. Perform self-diagnosis using CONSULT-IlI or “AIR BAG” warning lamp. Refer to SRS-27, "SRS Operation
Check (USER MODE)" for details. Ensure entire SRS operates properly. J
Only one front air bag may inflate a crash, depending on the crash severity and whether the front occupants
are belted or unbelted. This does not indicate improper performance of the system. Perform self-diagnosis to
make sure the entire SRS operates properly. K
SRS INSPECTION (FOR FRONTAL COLLISION)
Part SRS is activated SRS is NOT activated
L
Driver airbag If the Driver airbag has deployed: If the Driver air bag has NOT been activated:
module REPLACE. [same text as in current manual]
Install with new fasteners.
Passenger front If the Passenger front airbag has deployed: If the Passenger front air bag has NOT been activated: M
airbag module REPLACE. [same text as in current manual]
Install with new fasteners.
Crash zone If any of the front airbags or seat belt pre- If the front airbags or seat belt pre-tensionsers have NOT
sensor tensionsers have been activated: been activated:
REPLACE the crash zone sensor and bracket [same text as in current manual]
with new fasteners.
Seat belt pre-ten- If the driver or passenger Seat belt pre-ten- If the pre-tensioners have NOT been activated:
sioner assemblies sioner has been activated: [same text as in current manual]
REPLACE the seat belt pre-tensioner
assemblies with new fasteners.

Diagnosis sensor If any of the SRS components have been If none of the SRS components have been activated:
unit activated: [same text as in current manual]
REPLACE the Diagnosis sensor unit.
Install with new fasteners.

Revision: 2006 November SRS-53 2007 350Z

 COLLISION DIAGNOSIS

Part SRS is activated SRS is NOT activated

Steering wheel [same text as in current manual]

Spiral cable If the Driver airbag has deployed: If the Driver airbag has not deployed:
REPLACE the spiral cable. [same text as in current manual]

Harness and con- 1. Check connectors for poor connection, damage, and terminals for deformities.
nectors 2. Check harness for binding, chafing, cuts, or deformities.
3. If no damage is found, reinstall the harness and connectors.
4. If damaged—REPLACE damaged section of harness. Do not repair, splice or modify any SRS harness.
Instrument panel 1. Visually check instrument panel for damage.
2. If no damage is found, reinstall the instrument panel.
3. If damaged—REPLACE the instrument panel with bolts.

Revision: 2006 November SRS-54 2007 350Z

 COLLISION DIAGNOSIS

For Side Collision NHS00012

WHEN THE SIDE AIR BAG IS ACTIVATED IN THE SIDE COLLISION: A

1. Replace the following components:
– All parts of front seatback (including front seatback frame) with front side air bag module (on the side on
which front side air bag is activated) B
– Curtain air bag module (on the side on which side curtain air bag is activated)
– Diagnosis sensor unit
– Satellite sensor (on the side on which side air bag and side curtain air bag is activated) C
2. Check the SRS components and the related parts using the following table.
– Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,
D
deformation).
3. Perform self-diagnosis using CONSULT-IlI or “AIR BAG” warning lamp. Refer to SRS-27, "SRS Operation
Check (USER MODE)" . Ensure entire SRS operates properly.
E
WHEN SRS IS NOT ACTIVATED IN THE SIDE COLLISION:
1. Check the SRS components and the related parts using the following table.
– Replace any SRS components and the related parts showing visible signs of damage (dents, cracks, F
deformation).
2. Perform self-diagnosis using CONSULT-IlI or “AIR BAG” warning lamp. Refer to SRS-27, "SRS Operation
Check (USER MODE)" . Ensure entire SRS operates properly. G
SRS INSPECTION (FOR SIDE COLLISION)
Front side air bag and
Part side curtain air bag is Front side air bag and side curtain air bag is NOT activated SRS
activated
1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on
REPLACE the side the collision side. I
curtain air bag mod-
2. If damaged— Remove the side curtain air bag module.
ule.
(LH or RH) side cur- 3. Check for visible signs of damaged (tears etc.) of the side curtain air bag module.
(Repair the center pil-
tain air bag module*
lar inner, etc. before 4. Check harness and connectors for damage, and terminals for deformities. J
installing new one if
5. If no damage is found, reinstall the side curtain air bag module with new bolts.
damaged.)
6. If damaged—REPLACE the side curtain air bag module with new bolts.
Front (LH or RH) side REPLACE all parts of 1. Check for visible signs of damage (dents, tears, deformation) of the seat back on
K
air bag module seatback with the collision side.
deployed front side 2. Check harness and connectors for damage, and terminals for deformities.
air bag module. L
3. If no damage is found, reinstall the front seatback assembly.
4. If damaged—REPLACE the front seatback assembly.
(LH or RH) side air REPLACE the side 1. Remove the side air bag (Satellite) sensor on the collision side. Check harness
bag (Satellite) sensor air bag (Satellite) sen- connectors for damage, terminals for deformities, and harness for binding.
M
sor on the collision 2. Check for visible signs of damage (dents, cracks, deformation) of the side air bag
side with new nuts.
(Satellite) sensor.
(Repair the center pil-
lar inner, etc. before 3. Install the side air bag (Satellite) sensor to check fit.
installing new one if 4. If no damage is found, reinstall the side sir bag (Satellite) sensor with new nuts.
damaged.)
5. If damaged—REPLACE the side air bag (Satellite) sensor with new nuts.
Diagnosis sensor unit REPLACE the diag- 1. Check case and bracket for dents, cracks or deformities.
nosis sensor unit with 2. Check connectors for damage, and terminals for deformities.
the new bolts.
3. If no damage is found, reinstall the diagnosis sensor unit with new bolts and ground
bolt.
4. If damaged—REPLACE the diagnosis sensor unit with new bolts and ground bolt.

Revision: 2006 November SRS-55 2007 350Z

 COLLISION DIAGNOSIS

Front side air bag and

Part side curtain air bag is Front side air bag and side curtain air bag is NOT activated
activated
Seat belt pre-ten- 1. Check if the seat belt can be extended smoothly.
sioner assembly If the seat belt cannot be extended smoothly,
– Check for deformities of the center pillar inner.
– If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
2. Remove the seat belt pre-tensioner assembly on the collision side. Check harness cover and connectors
for damage, terminals for deformities, and harness for binding.
3. Check for visible signs of damage (dents, cracks, deformation) of the seat belt pre-tensioner assembly.
4. Check seat belt adjuster for damage.
5. If no damage is found, reinstall the seat belt pre-tensioner assembly.
6. If damaged—REPLACE the seat belt pre-tensioner assembly with new bolts.
Seat with front side REPLACE all parts of 1. Visually check the seat on the collision side.
air bag front seatback 2. Remove the seat on the collision side and check the following for damage and
(including front seat- deformities.
back frame)
– Harness, connectors and terminals
– Frame and recliner (for front and rear seat), and also adjuster and slides (for front
seat)
3. If no damage is found, reinstall the seat.
4. If damaged—REPLACE the damaged seat parts using new bolts.
Center inner pillar 1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).
2. If damaged—REPAIR the center inner pillar.
Trim/headlining* 1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the collision side.
2. If damaged—REPLACE the damaged trim parts.
*: For coupe

Revision: 2006 November SRS-56 2007 350Z