CHRYSO® PROOF ACRYLIC

Acrylic Polymer Based Elastomeric Heavy Duty

Waterproof Coating

Description Method of Application

Surface Preparation
CHRYSO PROOF ACRYLIC is acrylic polymer based elastomeric,
waterproofing protective coating system. In addition to UV Prior to application of CHRYSO PROOF ACRYLIC, all surfaces must
resistance acrylic polymer, CHRYSO PROOF ACRYLIC is designed be prepared properly to avoid failure. The surface shall be cleaned
with alkali-acid resistance micro-fibre enhance tensile strength to remove all dust, foreign material/loose particles or any deposit
proprietary additives to resist post growth of algae and fungus of contaminants, which could affect the bond between the
and selected pigments reduces surface temperature up to 15°C original substrate and the CHRYSO PROOF ACRYLIC system. This
when exposed to direct sun light. The thixotropic nature of the can be done by scarifying, grinding, water blasting, acid washing
coating helps to apply thick film to get desired film thickness (1 to or any other approved method. Rectify depression / honey-comb
1.5mm) with minimum no of coats. (if any) in the surface, use CHRYSO ARMOURCRETE mortar (1part
CHRYSO ARMOURCRETE, 2part cement, 4 part medium washed
Indicative Characteristics sand) and leave it for at least 24 hours before application of
CHRYSO PROOF ACRYLIC.
Appearance of dry film White, Grey. Other
colour may be available Treatment of Cracks
on request
Specific Gravity 1.3±0.1 If there is any crack up to 2 mm, clean those cracks with vacuum
Drying time at 30⁰C, RH 65% 12 hours cleaner, to open cracks, pour CHRYSO PROOF ACRYLIC PRIMER
Solid content, % (W/W) >65 followed by a coat of CHRYSO PROOF ACRYLIC along the crack line
% Elongation at 14 days, 250 ( minimum) and leave it to dry for over night.
ASTM D 412
Tensile strength at 14 days, MPa 2 and 5(with fibre Application of Primer
ASTM D 412 mesh reinforcement)
Hardness Shore A, ASTM D 2240 >40 Though CHRYSO PROOF ACRYLIC adheres strongly with most of
QUV Resistance, No crack, No color building materials like cement concrete, mortar, bricks, woods
ASTM G 154, 1000 hours change etc., use of CHRYSO PROOF ACRYLIC PRIMER provide better
Pull off Adhesion at 14 days, >1.5 performance of final coating system. Stir well the Primer and
ASTM D 4541, MPa apply it with soft nylon brush or roller over the dry surface.
Generally, one coat is sufficient. If the surface is too porous apply
Crack Bridging Capacity, EN 1062 2mm ( No pinhole, no
crack) two coats of primer. Time gap between two coats should be 2-3
hours.
Full Cure, at 30⁰C, 60% RH 14 days
Fungi Resistance, ASTM Passes test
Application of Proof Acrylic
D3273/3274
Water Vapor Permeance, perm, 13
After the application primer coat allow it to reach touch dry for 2-
ASTM D1653
3 hours. Stir CHRYSO PROOF ACRYLIC to a homogeneous smooth
Water Penetration at 5 Bar, Nil
consistency and apply it horizontally with soft nylon brush, roller
DIN 1048 Part 5
or squeeze to thickness of 500-600 microns in single coat. Allow
Fire Resistance, EN ISO 11925-2 Passes test it to dry for approx. 4-5 hours. When the applied coat becomes
SRI (Solar Reflectance Index) %, >88 (0-100 scale, Black sufficiently dry (no foot print observed) apply second coat
ASTM E 903 (CHRYSO PROOF Paint 0, Pure TiO₂ 100) vertically. Two coats are sufficient for general waterproofing
ACRYLIC- WHITE) (1mm thickness) but for severe conditions, three or more coats
Dirt Pick-up Resistance, Passes test are required to achieve desired results.
ASTM D 3719
Coverage (Theoretical, WFT) 1.2-1.3kg /mm/m²

The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
AB/25/02/2020

technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com

CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2
 CHRYSO® PROOF ACRYLIC
Acrylic Polymer Based Elastomeric Heavy Duty
Waterproof Coating

Domains of Application Precautions

 Waterproofing of old as well as new flat / slope  Reinforcement rods and other sharp materials should
concrete roof/ terrace/ podium not be dragged over the CHRYSO PROOF ACRYLIC
 Refurbishment of old concrete roof like brick bat coba, membrane, as this can puncture the same. CHRYSO
concrete screed/plaster, old acrylic coating, asphalt PROOF ACRYLIC shall always be used WITHOUT
coating, Old APP/SBS membrane, etc. dilution.
 Waterproofing / protective coating of metal/ asbestos  Do not apply coating thickness more than 600 microns
sheet roof. in one go. For higher coating thickness apply multiple
coat.
Advantages  There should not be any rain during and after
application of final coating for at least 6-8 hours
 Easy application; can be applied by brush, roller and  24 Hours pond test shall be carried out after 72 hours
of final coating application
squeegee at site.
 Not suitable for continuous immersion like basements,
 Elastomeric in nature; up to 2mm crack bridging water tanks/reservoirs and any other liquid storage
tanks.
capacity.
 UV Resistance- does not yellowing in sun rays Safety
exposure.
 Wear hand gloves, safety shoes and safety goggles
 Excellent resistance to carbon dioxide, acid rain, and while using and handling the product.
alkali solution.
 In case eyes or mouth are affected wash with plenty of
 Desired high Tensile strength can be achieved by clean water and seek medical treatment immediately.
providing single / multilayer glass fibre cloth.
Before use, refer to the Material Safety Data Sheet.
 Excellent resistance to dirt pick up. The MSDS is available on www.chryso.com
 No VOC (Volatile Organic Compound).
Shelf Life & Storage

12 months from the date of manufacturing when stored in un-

opened, original sealed and dry condition at a temperature
range from +5⁰C to 40⁰C.

Packing

20 kg Plastic Bucket

The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
AB/25/02/2020

technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com

CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2