Welcome To Ohana Industries LLC

Company Introduction

Why Thermal Insulation

XPS – Characteristics

OHANA EXPO FOAM Insulation

INDEX XPS – Sustainable Building Material

Different Types of Application for XPS

EXPO FOAM Technical Data Sheet

OHANA – ISO & EGBC CERTIFICATE

 Company Introduction
State-of-the-Art manufacturing facility
In National Industries Park
60000 Sq.ft .
Expanded Polystyrene
Extruded Polystyrene

Operations in
UAE
GCC

Management team has a combined technical experience of over 100 years in the industry
Success in EPS business
Forward Integration to XPS production
145000 CBM per annum

XPS boards
Preferred Insulation in building & Refrigeration segments
Low thermal conductivity
Excellent compressive strength
Resistance to moisture
 What is Thermal Insulation
Thermal insulation is the method of preventing heat from escaping a Building or from
entering the Building.

The thermal insulators are referred to materials used to reduce the rate of heat transfer.

The heat can be transferred by 3 mechanisms:

Convection: Convection is the transfer of heat energy in a gas or liquid

by movement of currents.

Conduction: Conduction is the transfer of energy through matter

from particle to particle.

Radiation: Electromagnetic waves that directly transport ENERGY through

space. Sunlight is a form of radiation that is radiated through
space to our planet without the aid of fluids or solids.
 Why Insulate
Buildings?
Thermal insulation is the method of preventing heat from escaping a Building or from
entering the Building.
Technical:

Cold Climate: In cold conditions, the main aim is to

reduce heat flow out of the building, to keep living
space warm.

Hot Climate: In hot conditions, the greatest source of

heat flow is solar radiation. The aim is to reduce the
flow of heat inside the building.
Environmental:
“Go Green – Plan for a better tomorrow”.
Use Energy as efficiently as possible.

Economical:
The use of thermal insulation in building walls and roof
does not only contribute in reducing the required It saves up to 35 to 40% on your
air-conditioning/ heating system size but also in
reducing the annual energy cost. electricity bills
 Why Extruded Polystyrene For Thermal Insulation
The process of extruding foamed polystyrene results in a material with uniformly small, closed
cells, a smooth ‘skin’ and an unrivalled set of properties which make it the choice of specifiers in
a wide range of demanding insulation applications.
4. Chemical Resistance: The following
XPS is resistant to many common properties makes
chemicals such as: acids, bases, Extruded Polystyrene
water and water- based paints, an ideal choice for
alcohol and alcohol-based paints,
brine or salt water, cement and
thermal insulation:
mortars, asphalt, etc.

3. Moisture Resistance:
The superior moisture resistance and
very low vapour permeability of 1. R- Value:
extruded polystyrene insulation The ability of an insulation to resist heat
provides outstanding benefits for most flow. The higher the R-value, the greater
construction and engineering the insulating power. XPS has excellent
applications. long term R-value and proven.

2. Mechanical Properties:
High and uniform
compressive strength.
OHANA EXPO FOAM – XPS Insulation
Description:
OHANA EXPO FOAM is a thermal insulation
material in form of rigid boards, made of rigid
boards. The boards have a closed-cell
structure and therefore they are resistant to
water and humidity. They have excellent
thermal insulation and compressive strength
property.
Specifications
Dimensions EXPO FOAM
Thickness 25, 40, 50 ,75, 80, 90 & 100 mm
Board Size 1250mm x 600 mm
Edge Profiles Shiplap , Square Edge
Surface Smooth
Density 32-35kg, 35-40kg, 40-45kg, 45 to 50kg
 Light Weight & Inert
Safe to handle
Good Insulation
Saves Energy
No Ageing
Constant performance for years
XPS – No degradation
Recyclable Same or other form
Sustainable Fits Perfectly into UAE’s Retrofit Initiative

Building Products offered in two variants

CFC and HCFC free

Material CFC HCFC and HFC free

100 % recyclable. No stress on environment
XPS replaces brick and mortar in many areas & Saves on
Water.
 EXPO FOAM - Application Fields
EXPO FOAM – Extruded polystyrene
is utilized for the thermal
insulations of:
▪ Flat roofs, either accessible or inaccessible, as
inverted roof construction.

▪ Roof Gardens.

▪ Flat roof parking decks.

▪ Exterior walls of buildings insulated either on

the inner or outer face.

▪ Below-grade exterior walls of

basements (Perimeter insulation).

▪ On-grade floors of buildings.

▪ Cold store insulations.

 XPS – FLAT ROOF INSULATION
NO Roof Assembly Details
1 Reinforced concrete slab 7

2 Sloping screed
3 Modified Waterproofing membrane 6

5
4 Expo Foam Thermal Insulation Board 4
3
5 Geo textile separation Layer
2
6 Paving slabs/ Tiles 1
7 Parapet with Aluminum Skirting

▪ Application of the layers in accessible flat roof insulation is the same as the inaccessible, starting from
the bottom and including the separation layer.
▪ Paving of slabs or tiles using mortar and sand.
▪ Paving slabs serves as the protective layer against UV radiation and they form the load against the uplift
of wind.
▪ The minimum thickness of paving slab should not be less than 4 cm.
 Roof Garden Insulation
No. Roof Garden Details
1 Reinforced concrete slab
2 Sloping screed
3 Modified Waterproofing
membrane
4 OHANA EXPO FOAM
Insulation Board
5 Separation Layer
6 Ballast
7 Separation Layer
3

8 Soil 2

9 Parapet fixing 1

▪ Application of the layers in roof garden insulation is the same as the inaccessible, starting from the
bottom and including the separation layer.
▪ A 2nd separation layer of the non-woven is laid over the ballast layer and the application is
completed by laying the soil over it.
▪ Care should be taken to slope the screed such that it should not be disturbing for the people using
the roof garden.
 OUTSIDE INSULATION OF EXTERIOR WALL

No. Wall Insulation Details

1 Exterior Wall

2 Fixing Mortar

3 Plastic Anchor

4 Expo Foam Thermal Insulation Board

5 Undercoat Plaster

6 Reinforcement Mesh

7 Undercoat Plaster

8 Plaster Finish

▪ EXPOFOAM XPS board is applied on the surface of the wall temporarily by fixing mortar and then fixed by
using plastic anchors. 5 anchors per board are sufficient.
▪ After applying the 1 st layer of undercoat plaster, the reinforcing mesh is adhered to it and stretched
throughout the surface to be plastered.
▪ The 2 nd layer of undercoat is applied over the mesh and completed with plaster finish
 BELOW-GRADE EXTERIOR WALL INSULATION (PERIMETER
INSULATION)

No. Basement Insulation Details

1 Basement Wall

2 Leveling Plaster

3 Modified Waterproofing membrane

4 Expo Foam Thermal Insulation Board

5 Protection Wall

6 Back Filling

▪ The Insulation of below-grade exterior walls of basement, EXPO FOAM board is applied loose over the
waterproofing membrane protects the membrane from possible damage along with thermal insulation to the
basement of the building.
▪ Protective wall is erected to hold the insulation boards in place and back filling.
 Car Park Flat Roof Insulation
No. Roof Assembly Details
1 Reinforced concrete slab
2 Sloping screed
7

3 Modified Waterproofing membrane

6

5
4 OHANA EXPO FOAM Insulation Board 4

3
5 Separation Layer 2

6 Paving slabs/ Tiles 1

7 Reinforced concrete slab

▪ Application of the layers in Car park flat roof insulation is the same as the inaccessible, starting
from the bottom and including the separation layer.
▪ It is advisable to prepare sloping screed with normal aggregate instead of porous aggregate and
add some reinforcement for load bearing purpose..
▪ Reinforced concrete of estimated thickness and reinforcement is cast over the ballast layer.
 EXPO- FOAM Extruded Polystyrene Insulation Boards

TECHINICAL DATA SHEET

Classification Type as per ASTM C-578 15B

S.No. Properties Test Method Unit TYPE VI TYPE VII TYPE V

Compressive Strength @ yield

or
1 ASTM D-1621 kPa 300 414 690
10% deformation, which
occurs first, min kPa

Thermal resistance of 25.4 mm

thick XPS material @ mean
2 ASTM C-518 K.m2/W 0.84 0.84 0.84
temperature of 35⁰C and 60%
RH,Minimum

Thermal Conductivity,@mean
3 temperature of 35⁰C and 60% ASTM C-518 ASTM C-518 0.0303 0.0303 0.0303
RH,Maximum

ASTM C203, Method

4 Flexural Strength, min kPa 414 517 690
I, Procedure B.

Water Absorption by ASTM D 2842 (+1% By

5 % by vol. 0.3 0.3 0.3
Submersion, min. vol. precision)

6 Water Vapour Permeance, max ASTM C 355 Perm/inch 1.1 1.1 1.1

Dimensional Stability (Change in

7 ASTM D 2126 % 2 2 2
dimension), max."

8 Oxygen Index, min. ASTM D 2863 Vol., % 24 24 24

9 Density, Minimum. kg/m3 ASTM D 1622 Min-29 Min-35 Min-48

 CERTIFICATE
This is to certify that the
Environmental Management System of

OHANA INDUSTRIES L.L.C

PLOT# TP070602, NATIONAL INSUSTRIES PARK,
P.O. BOX: 6584, DUBAI, UNITED ARAB EMIRATES.

has been found to comply with

ISO 14001:2015
This certificate is applicable to the following scope:

PACKING & PACKAGING MATERIALS MANUFATURING.

Certificate No :: BESC202203002
Date of Initial Registration 05 March 2022

Surveillance Audit on/before 05 February 2023

Certificate Expiry 05 March 2023

Recertification Due 04 March 2025

*The scope is as per IAF Code 14

Authorized Signatory
BQC ASSESSMENT PRIVATE LIMITED
Website: www.bqccert.com, E-mail: [email protected],
MSCB -124
BQC Assessment Pvt. Ltd. is accredited by International Accreditation Services (IAS), United States of America vide MSCB Number 124.
Accreditation details are available with IAS, (International Accreditation Service) Inc. USA, at www.iasonline.org
The validity of this certificate can be verified at www.bqccert.com or through [email protected]
Address: 202, DLF Galleria, Mayur Vihar, Delhi -110091. This certificate is the property of BQC
 CERTIFICATE
This is to certify that the
Occupational Health & Safety Management System of

OHANA INDUSTRIES L.L.C

PLOT# TP070602, NATIONAL INSUSTRIES PARK,
P.O. BOX: 6584, DUBAI, UNITED ARAB EMIRATES.

has been found to comply with

ISO 45001:2018
This certificate is applicable to the following scope:

PACKING & PACKAGING MATERIALS MANUFATURING.

Certificate No :: BOSC202203002
Date of Initial Registration 05 March 2022

Surveillance Audit on/before 05 February 2023

Certificate Expiry 05 March 2023

Recertification Due 04 March 2025

*The scope is as per IAF Code 14

Authorized Signatory
BQC ASSESSMENT PRIVATE LIMITED
Website: www.bqccert.com, E-mail: [email protected],
MSCB -124
BQC Assessment Pvt. Ltd. is accredited by International Accreditation Services (IAS), United States of America vide MSCB Number 124.
Accreditation details are available with IAS, (International Accreditation Service) Inc. USA, at www.iasonline.org
The validity of this certificate can be verified at www.bqccert.com or through [email protected]
Address: 202, DLF Galleria, Mayur Vihar, Delhi -110091. This certificate is the property of BQC
 CERTIFICATE
This is to certify that the
Quality Management System of

OHANA INDUSTRIES L.L.C

PLOT# TP070602, NATIONAL INSUSTRIES PARK,
P.O. BOX: 6584, DUBAI, UNITED ARAB EMIRATES.

has been found to comply with

ISO 9001:2015
This certificate is applicable to the following scope:

PACKING & PACKAGING MATERIALS MANUFATURING.

Certificate No :: BQSC202203006
Date of Initial Registration 05 March 2022

Surveillance Audit on/before 05 February 2023

Certificate Expiry 05 March 2023

Recertification Due 04 March 2025

*The scope is as per IAF Code 14

Authorized Signatory
BQC ASSESSMENT PRIVATE LIMITED
Website: www.bqccert.com, E-mail: [email protected],
MSCB -124
BQC Assessment Pvt. Ltd. is accredited by International Accreditation Services (IAS), United States of America vide MSCB Number 124.
Accreditation details are available with IAS, (International Accreditation Service) Inc. USA, at www.iasonline.org
The validity of this certificate can be verified at www.bqccert.com or through [email protected]
Address: 202, DLF Galleria, Mayur Vihar, Delhi -110091. This certificate is the property of BQC