Scribd
Upload
15 views32 pages

Matlab Simulation Lab Manual

The document is a laboratory manual for a MATLAB simulation practice course in Electrical Engineering for the 4th semester. It outlines a series of experiments focusing on functions, operations, and simulations related to electrical circuits, including Thevenin's theorem and various types of rectifiers. Each experiment includes aims, required apparatus, procedures, and results, emphasizing hands-on learning through digital simulation.

Uploaded by

kc9ova
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views32 pages

Matlab Simulation Lab Manual

The document is a laboratory manual for a MATLAB simulation practice course in Electrical Engineering for the 4th semester. It outlines a series of experiments focusing on functions, operations, and simulations related to electrical circuits, including Thevenin's theorem and various types of rectifiers. Each experiment includes aims, required apparatus, procedures, and results, emphasizing hands-on learning through digital simulation.

Uploaded by

kc9ova
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 32

LABORATORY MANUAL

SIMULATION PRACTICE ON MATLAB


BRANCH- ELECTRICAL ENGINEERING

SEMESTER- 4TH

Department of Electrical Engineering

O.S.M.E ,KEONJHAR
LIST OF EXPERIMENT
1. FUNCTION AND OPERATIONS USING VARIABLES AND ARRAYS TO LEARN ARITHMATIC
OPERATION.

2. FUNCTION AND OPERATIONS USING VARIABLES AND ARRAYS TO LEARN RELATIONAL AND
OPERATORS.

3. FUNCTION AND OPERATIONS USING VARIABLES AND ARRAYAS TO LEARN


TRIGONOMETRIC AND MANPULATION.

4. MATRIX FORMATION AND ITS MANIPULATIONS.

5. USE OF LINESPACE COMMAND TO CREATE VECTORS, ADD AND SUBTRACT VECTORS.

6. GENERATION OF THE SINE AND SQURE ROOT FUNCTIONS WITH VECTOR ARGUMENTS.

7. PLOTTING AND LABELLING OF TWO DIMENTIONAL FUNCTION LIKE sin (t), cos(t), tan(t), sec(t)
FOR A GIVEN DURATION.

8. TO WRITE PROGRAM OF REPRESENTATION OF BASIC CONTINOUS SIGNAL.

9. USE OF COMON USED BLOCK OPERATION BLOCK AND DISPLAY FROM MATLAB AND
SIMULINK LIBRARY.

10.VERIFICATION OF THEVINISH THEROM USING MATLAB SIMULINK.

11.SIMULATION OF SINGEL PHASE HALF WAVE PHASE CONTROLLED CONVERTER WITH R AND
R-L LOAD ON MATLAB.

12. SIMULATION OF SINGEL PHASE HALF WAVE AND FULL WAVE DIODE RECTIFIER
WITH R AND R-L LAOD ON MATLAB
EXPERIMENT NO -10
AIM:
To verify Thevenin’s theorem using digital simulation.
APARATUS:
DESK TOP
S. No SOFTWARE USED
QUANTITY
1 MATLAB 01

CIRCUIT DIAGRAMS:

Fig 1 Measurement of V

Fig 2 Measurment of I
PROCEDURE:

1. Make the connections as shown in the fig 1 diagram by using MATLAB Simulink.
2. Measure the open circuit voltage across the load terminals using voltage
measurement.
3. Connect circuit fig 2 Thevenin’s equivalent circuit in MATLAB
and find the loadcurrent.
EXPERIMENT NO 11

Aim: Simulation of single phase half wave phase controlled converter with R and R-L loadon MATLAB.

Apparatus Required: MATLAB/SIMULINK installed on PC.

Theory:
The phase controlled rectifiers using SCRs are used to obtain controlled dc output voltages from thefixed ac mains input
voltage. A single phase half wave controlled converter only has one SCR is employed in the circuit. The performance of
the controlled rectifier very much depends upon the type and parameters of the output (load) circuit.

Procedure:
1. Make the connections as per circuit diagram with elements taken from the MATLAB library for
both R & RL load.
2.Simulate them.
3.Observe the waveform carefully on scope.

Result:
Simulation of half wave controlled rectifier with R & RL load have been simulated.

Circuit Diagram:

Figure 1 Simulink model of single phase half wave with R load


Wave forms of gate pulse, input voltage, output voltage and load current of single phase half wave
with R load with firing angle 600
EXPERIMENT NO 12

Aim:- .Simulation of single phase half wave and full wave diode rectifier with R and R-L load onMATLAB

Software used:- Matlab

Single phase full wave rectifier:-


Primary function of full wave diode rectifier simulation is to establish a dc level from a sinusoidal input voltage that has zero
voltage. Single phase supply, is a fully controlled bridge- circuit .In the bridge circuit, diagonally opposite pairs of diodes
are made to conduct, and are commutated,simultaneously.

During the first positive half-cycle, diodes D1 and D2 are forward biased and if they are triggered simultaneously, then current
flows through the path L-D1-R-D2-N. Hence, in the positive cycle, diodes D1 and D2 are conducting.

During the negative half cycle of the a.c. input, diodes D3 and D4 are forward biased and if they are triggered simultaneously,
current flows through the path N-D3-R-D4-L. Diodes D1, D2 and D3, D4 are triggered at the same firing angle α in each
positive and negative half-cycles of the supply voltage, respectively.

When the supply voltage falls to zero, the current also goes to zero. Hence, diodes D1 and D2 in positive half cycle and D3,
D4 in negative half cycle turn off by natural commutation.

The related voltage and current waveforms for the circuit are shown in the figure given below the circuit diagram;

Procedure:-
1) Start the Matlab software.
2) Open a new simulation window by clicking on simulink button.
3) Window that appears in simulink library browser the window contains component that canbe
plotted into simulink or design window.
4) Drag & drop the components from library.
5) Run the simulation.

Figure:-

simulink model of half wave rectifier


wave forms of half wave rectifier in terms of input voltage ,load voltage ,load current andvoltage across diode

simulink model of Half wave rectifier

wave forms of half wave rectifier in terms of input voltage ,load voltage ,load current andvoltage across diode
Result:-
Single phase Half wave and full wave diode rectifier has been studied.

Precautions:-
1) Connections must be properly alone.
2)Don’t forget to drag powergui beside circuit diagram

You might also like