_J L _J L

TECHNICAL DATA
UltraTech AS PER RELEVANT IS AND ASTM STANDARDS
BASEKRETE
Multi Purpose Mortar Bulk density 1550-1650 Kg/m3
Series: BSK0009
Month: December 2017 Water powder ratio 17-19%
Supersedes all earlier TDS
Description Pot life 1 hour
UltraTech BASEKRETE is a polymer modified cement based high performance pre-mixed high strength mortar specially
Subsequent usage time 48hours
formulated for multipurpose applications.
Compressive strength @ 28 Days without extra addition of fine aggregates 20-25 N/mm2
Specification
Technical Parameters complies with IS 2250. Compressive strength @ 28 days with addition of M-Sand/River Sand at 1:1 13-15 N/mm2

proportion by weight

Features & Benefits 0.40 Sq.ft.

Coverage @ 12 mm per Kg
• Consistent Quality due to
superior raw materials used • Faster applications up to • Ready to use mortar just Thickness range of application 15-25 mm
25 mm thickness by adding water
• Excellent adhesion and
• Ready to use after 48 hours • Well graded good quality Curing time 2 Days @ 3 times a day
compressive strength
dependent on thickness, sand and fillers which
• Optimum pot life ambient temperatures enhances the durability
and humidity • Reduced wastages
Note Safety Directions
Areas of Application Allow a minimum of 48 hours for the subsequent usage over UltraTech BASEKRETE is non-toxic. Use of gloves and
Suitable for application in brick/block laying, for thicker plasters for external and internal areas which demand high strength. the UltraTech BASEKRETE applied areas. Do not apply if goggles recommended. Any splashes to the skin or eyes
UltraTech BASEKRETE can also be used as a polymer modified repair mortar for old surface repairs. Ideal for plastering inside temperatures are likely to drop to below 5°C or exceed 50°C. should be washed off with clean water immediately.
swimming pools, water tanks, foundation areas and basements. Curing to be extended from normal 2-3 days as per the In case of prolonged irritation, medical advice should be
actual temperature in site conditions.
UltraTech BASEKRETE can also be used as an underlayment plaster for tile adhesives to provide the required strength of plaster sought. UltraTech BASEKRETE is non-flammable.
underneath the Tile adhesive to hold the special/large sizetilesover vertical surfaces. The technical data provided in this technical data sheet is as
per our internal lab testing and may vary as per the actual
method of application at sites. Other Product Categories available with
UltraTech Building Products Division
METHOD OF APPLICATION Consult UltraTech Building Products Division Technical
Services Cell for any further technical assistance. • Tile Adhesives

Surface • Prior to application of UltraTech BASEKRETE, surface should be clean, free of oil, grease and paint. • Micro Concrete
Packaging
Preparation Defects deeper than 25 mm should first be patched • Industrial/Precision Grout andAnchors
40Kg
• Water Proofing and Injection Grouting Material
• It is advisable to have adequate roughness on the concrete surface to have the required adhesion
Shelf Life • Plasters and Jointing Mortar
UltraTech BASEKRETE has a shelf life of 12 months from • Floor Screeds
the date of manufacture. Store at cooland dry place. • Autoclaved Aerated Lightweight Concrete Blocks

Mixing
• Mix UltraTech BASEKRETE with 17-19% by weight of water using mechanical stirring for 2-3 minutes
to ensure a consistency free of lumps
• Addition of M-Sand, River Sand is also recommended by 1:1 proportion by weight to UltraTech
BASEKRETE for higher volume applications

Application • Use spatula/trowel for the UltraTech BASEKRETE applications and the final level can be attained
with aluminum floats/levelers DISCLAIMER
Information provided on this data sheet is the guideline for usage. Users are advised to undertake a trial for product suitability prior to it's full scale usage.
There is no implied guaranty/warranty for the results and the company is not liable for any consequential damages.
• UltraTech BASEKRETE can be applied for thickness up to 25 mm. For thickness above 25 mm,
) multiple layer application can be adopted
7 7