LCD READOUTS

OPERATION MANUAL

NO.1
 Contents

Safety Precautions-----------------------------------------------------------3
Product inspection and installation --------------------------------------------4
1. Panel Figure---------------------------------------------------------------4
2. System parameter ---------------------------------------------------------5
2.1 System function parameter setting instructions -------------------5
2.2 Parameter setting instructions --------------------------------------6
2.2.1 Restore factory default settings------------------------------6
2.2.2 Position display mode ----------------------------------------6
2.2.3 Position sensor type ------------------------------------------6
2.2.4 Counting resolution------------------------------------------6
2.2.5 Counting direction--------------------------------------------6
2.2.6 Compensation mode ------------------------------------------6
2.2.7 Rotary encoder lines ------------------------------------------7
2.2.8 Screw gap------------------------------------------------------7
2.2.9 Coordinate joint-----------------------------------------------7
2.2.10 The decimal places of imperial-----------------------------7
2.2.11 Anti-interference level --------------------------------------7
2.2.12 Angle type----------------------------------------------------8
2.2.13 Screen time---------------------------------------------------8
2.2.14 Language type -----------------------------------------------8
2.2.15 Anti-shake level----------------------------------------------8
2.2.16 RS485 baud rate ---------------------------------------------8
3. Basic function operation-------------------------------------------------8
3.1 Reset-------------------------------------------------------------------9
3.2 Input preset data for an axis ----------------------------------------9
3.3 mm/inch -------------------------------------------------------------10
3.4 Absolute / relative / user coordinate system ---------------------10
3.5 Automatically divide by 2------------------------------------------10
3.6 SDM General Clearance--------------------------------------------10
3.7 Screen saver function-----------------------------------------------10
3.8 Power-down memory function-------------------------------------10

1
 3.9 Linear compensation function-------------------------------------11
3.10 Non-linear compensation-----------------------------------------11
3.11 Anti-shake switch--------------------------------------------------12
3.12 Lathe diameter radius switch-------------------------------------12
3.13 coordinate joint switch--------------------------------------------12
3.14 Brightness adjustment --------------------------------------------13
4. 200 groups of user coordinate system zero function-----------------13
4.1 Zero-in-place--------------------------------------------------------14
4.2 Preset SDM zero position------------------------------------------14
5. Dedicated functions-----------------------------------------------------15
5.1 Circumferential hole----------------------------------------------15
5.2 Linear hole ---------------------------------------------------------16
5.3 Smooth arc ----------------------------------------------------------17
5.4 Simple arc ----------------------------------------------------------18
5.5 Bevel machining ---------------------------------------------------19
5.6 Network hole--------------------------------------------------------20
5.7 Inner machining-----------------------------------------------------21
5.8 EDM -----------------------------------------------------------------22
6. Calculator function------------------------------------------------------23
7.Appendix------------------------------------------------------------------23
8.FAQ -----------------------------------------------------------------------27
9.Disclaimer----------------------------------------------------------------28

Respected user:
Thank you for purchasing ToAuto multi-function display meter system.
Grating digital display system is widely used in milling, grinding, wire
cutting, lathe, EDM and other processing equipment. Before use, please read the
instructions carefully to facilitate correct and safe operation of the product.

2
Notice:
* This product is an electrical product, and safety precautions should be followed
to avoid accidents.
* In this manual, important items for preventing accidents and how to use the product
are pointed out. Please read this manual carefully to use this product safely.
* After reading, please keep it in a safe place for easy reference.
* This product complies with CE certifications, and has applied for industry patents,
counterfeiting must be investigated.
2 Axis or 3Axis Digital Readout Can be selected, according to your needs.

Safety Precautions
* When this system is used with a digital sensor, which is not necessarily the same
function and wiring, do not connect with other companies scales to avoid damage.

* When a failure occurs, do not open the digital display system by yourself to avoid
accidents such as electric shock and fire. Please contact customer service
([email protected]) for professional maintenance.

* This system uses AC110V ~ 220V, 50HZ ~ 60HZ AC power. When not in using,
please turn off the power as much as possible.

* To prevent electric shock or fire, do not get wet or splash directly with the cooling
liquid. If you see smoke or strange smell from the digital display, please unplug
the power plug immediately, otherwise it will cause fire. Please contact our
company or dealer, do not try to repair it yourself.

* This device is not intended to be used by persons (including children) with

physical, sensory, or mental impairments or lack of experience and knowledge,
unless they are supervised and instructed by those responsible for their safety,
children should be supervised to ensure that They do not play with this device.

3
Product inspection and installation
This product has been fully functionally tested before shipping out. In order
to prevent the product from not working properly due to external force during
the product delivery process, please check the following items in detail after
unpacking:
1. Check whether the appearance of the machine is consistent with the ordered model.
2. Check whether the appearance of the machine is in good condition. If there is
damage during transportation, please do not power on.
3. Check whether there are parts or screws falling off or loose in the machine.

If the above situation occurs, or other abnormal phenomena, please contact

the manufacturer immediately.

1. Panel Figure

Length: 280mm (11.02″) Height: 175mm (6.88″)

4
 2. System Parameter

2.1 System function parameter setting instructions

Set the system parameters correctly according to the resolution or line number
used by the position sensor, and the installation direction. When the parameter
setting is correct, please do not enter the parameter setting state again to avoid
disoperation and affect normal use.

When the system enters the main interface, press the key, the parameter
password window pops up, please enter 2008 to enter the parameter
interface. Press and find the parameter interface to be set. Press
and restore system default configuration data. Press and save system
parameters. Press or number key and enter parameter modification. Press
or and exit parameter modification.

5
2.2 Parameter setting instructions
2.2.1 Restore factory default settings

Press and restore factory settings, when pop-up and enter

2008, it will restore factory value successfully.

2.2.2 Position display mode

Press and select setup parameters, under , press
and select display method: Angle or Line.

2.2.3 Position sensor type ·

Press and select the parameter area to be modified. Under

, press to select sensor type:Encoder or Grating. Each line

corresponds to the corresponding axis parameter.

2.2.4 Counting resolution

Press and select the parameter area to be modified.

Under , press to select count resolution or enter data directly

by directly pressing the numeric area of the keyboard, unit (um) .Each line
corresponds to the corresponding axis parameter.

2.2.5 Counting direction

Press and select the parameter area to be modified.

Under , press and select the direction of count:Forward or

Reverse. Each line corresponds to the corresponding axis parameter.

2.2.6 Compensation mode

Press and select the parameter area to be modified

Under ,press to select compensation mode: Lineco or Segco.

Each line corresponds to the corresponding axis parameter.

6
 2.2.7 Rotary encoder lines

Press and select the parameter area to be modified.

Under , enter the data directly to set the number of encoder lines. Note:
The value of this rotary encoder line is not processed by 4 times.

2.2.8 Screw gap

Press and select the parameter area to be modified.

Under , enter data directly to set lead screw gap, unit(mm).

2.2.9 Coordinate joint

Press and select the parameter area to be modified.

Under , press to select coordinate joint mode:NC-No

joint coordinates. If you should joint X and Y axis, please press to select
X = X+Y, then the X coordinate display value is X+Y.

2.2.10 The decimal places of imperial

Press and select the parameter area to be modified.

Under , press to select decimal places of imperial, 5:

We have five decimal places (imperial), 4: We have four decimal places (imperial).

2.2.11 Anti-interference level

Press and select the parameter area to be modified.

Under , press to select the anti-interference level. In

the severe environment where the interference situation is very serious, you can
appropriately increase the anti-interference level. This not only makes the position
count more stable, but also improves the accuracy of the displacement data. The
default is level 6.

7
 2.2.12 Angle Type

Press and select the parameter area to be modified.

Under , press to select Angle Type (DDD or DMS). In the

position display, whether it is displayed in micrometers or degrees minutes and
seconds: Micrometers or degrees minutes and seconds display.

2.2.13 Screen time

If you do not operate the instrument for a long time, you can set the screen
time. Pr ess to select the parameter area to be modified.

Under , press to select the screen time.

2.2.14 Language Type

Users can choose the language that the system supports, press
to select the parameter area to be modified. Under ,
press to select the language.

2.2.15 Anti-shake level

Sometimes the machine shakes seriously. When the display position sensor
shakes or the position data flickers, you can set the Anti-shake level to eliminate
the digital jitter. Press to select the parameter area to be modified.
Under , press to select the Anti-shake level.

2.2.16 RS485 Baud rate

The system and the external device read the position data through RS485
communication, pair with the Baud rate of the external device, communication
format, 1 stop bit, no parity check bit, data bit is 8. Press
to select the parameter area to be modified. Under
press to select the Baud rate.

8
 3. Basic function operation

3.1 Reset
Press or and to reset the coordinates of current position, if you
press the key or and again, you can retrieve the data before reset.

3.2 Input preset data

Press or and to set the current coordinate data. For example X
axis=180.010, first press key, then press180.010, last press ,Setting data

9
 3.3 mm/inch
Press to select mm/inch. At the same time, the coordinate information area
displays the corresponding changes. For example, the metric unit MM is switched
to the inch unit INCH. The operation is as follows:

3.4 Absolute / Relative /User coordinate system

Press to select the ABS or INC, in order to switch between absolute and
relative coordinate systems, at the same time, the coordinate information area
displays the corresponding changes. You can also press the keys to
switch.

3.5 Automatically divide by 2

Press and then press / / , the data displayed in the data
display area is one-half of the original data. For example, the original X
axis=25.4000, press and , it is 12.7000. The diagram is as follows:

3.6 SDM
Press with 10 times, the user coordinate is cleared. If the absolute coordinate
system data is zero, all SMD data will be cleared.

3.7 Power-down memory function

In the event of a power failure, the system can remember the coordinates and
data before the power failure.

3.8 Power-down memory function

In the event of a power failure, the system can remember the coordinates and
data before the power failure.value.

10
 3.9 Linear compensation function
The function setting is determined according to the system parameter axis. If
the corresponding axis is linear function, a linear setting window will pop up. If it
is non-linear, a non-linear setting window will pop up. If the parameter is setting to
linear compensation function, the operation method is clicking or and ,
then clicking (MM/INCH) to pop-up linear compensation window. The X-axis

linearity compensation in the diagram is as follows: , Press

to set the corresponding standard position value and observation position

value.

3.10 Non-linear compensation

If the system parameter is setting to non-linear compensation, the operation

method is clicking / / , then clicking (MM/INCH) to pop up

11
nonlinear compensation window. The X-axis nonlinear compensation in the
diagram is as follows: Before setting, if the corresponding axis of the non-linear
compensation does not set the machine zero, you must select the item in the first
column, and then press the corresponding axis or and to set any
absolute zero which you want. Then set the corresponding data according to the
figure. Note: Non-linear compensation is arbitrary zero compensation, it must be
one-way sequential segment compensation.

3.11 Anti-shake switch

Press key on the main interface to pop up the corresponding menu options,

as the picture shows: Press to select the Anti-shake.

Then click to choose to turn this NO or OFF. If turned on, the corresponding mark

will be displayed in front of the axes.

3.12 Lathe diameter radius switch

Press on the main page to pop up the corresponding menu options:

Press to select X-Diameter, then clicking to select

ON or OFF. If it is turned on, the corresponding mark will be displayed before the
axis name in the coordinate area. This function is only valid for the X coordinate,

because the lathe is tentatively valid for the X axis.

3.13 Coordinates joint switch

Press on the main page to pop up the corresponding menu options:

Press to select joint: ON or OFF options, then clicking

12
 to enter ON or OFF. Note: If the system parameter joint setting is NC,

pressing the key is invalid.

3.14 Brightness adjustment

Press on the main page to pop up the corresponding menu options:

Press to select Brightness adjustment options, then

clicking to popup the brightness window: last clicking

to adjust the brightness. If you want to exit, press or .

5. 200 groups of user coordinate system zero function

The digital display system table provides three coordinate systems: absolute
coordinate system (ABS), relative coordinate system (INC), and 200 sets of user
coordinate systems (SDM1 ~ SDM200). 200 sets of user coordinate system can be
used as auxiliary zero position during processing.
ABS is an absolute coordinate system, which is established at the beginning
of machining a work piece and serves as the original reference point for machining
the work piece. The 200 sets of user coordinate systems are defined relative to the
absolute coordinate system. The user can store the working origin coordinates of a
machining part in each of the 200 sets of user coordinate systems.
For example: To process the work piece shown in the figure below, the ABS
origin is set at the center point of the work piece, and the remaining four auxiliary
zero positions are shown in the figure, SDM1, SDM2, SDM3, and SDM4; this may
be set in two ways:

13
(1). Zeroing at the Current Point

(2). Type directly

Before entering SDM, find the work piece
center according to the method of automatic
division by 2, which is the ABS origin
and can be set at the center O point of the
rectangle. Then click to reset.

4.1 Zero-in-place
After setting the work piece reference zero position to the zero point of the
ABS coordinate system, directly move the table to the position of each SDM origin
and clear it. During processing, in the SDM coordinate system, you only need to
move the table to the position with the display value of "0.000", and then you can
process.

(1)Press to enter SDM user coordinate system interface. The

information window displays SDM1, set the first zero point (sdm1), move the work
piece to the position of X = 60.000, Y = 45.000, that is the position of sdm1. Last

press to clear the X and Y coordinates respectively.

(2)Move to the user coordinate position of sdm2 (60.000, -45.000), sdm3

(-60.000, -45.000), sdm4 (60 --- 60.000,45.000) in turn. Last press to

clear the X and Y coordinates respectively.

4.2 Preset SDM zero position

After moving the work piece reference zero ABS coordinates to the work piece
center zero, directly input user coordinate positions of sdm1 (60.000, 45.000),
sdm2 (60.000, -45.000), sdm3 (-60.000, -45.000), and sdm4 (-60.000, 45.000)in turn.

14
 5. Dedicated
5.1 Circumferential hole
Function: PCD automatic calculation function, which can be used to process
the uniformly distributed holes on the plane arc. When using, just enter the data
corresponding to the corresponding function as shown in the figure below, and then
press Run to enter the operation processing interface.
First clicking F6 to select circumferential hole, second clicking the ,
last clicking key to enter the following figure for work piece processing:

15
 5.2 Linear hole
The oblique line function has a plane selection in the three-axis display table,
and no plane selection in the two-axis display table. The default is XY plane
processing, when using, just enter the correct data you want for the corresponding
function shown in the figure below, and then press Run to enter the operation
processing interface.
First clicking F6 to select Linear Hole, second clicking the , last
clicking key to enter the following figure for work piece processing:

16
 5.3 Smooth Arc
When using a milling machine to process parts, arcs are often processed. Using
the arc calculation function can quickly and easily meet the operator's requirements.
Enter the correct data of the corresponding function as shown in the figure, and
then press Run to enter the operation processing interface.
First clicking F6 to select Smooth Arc, second clicking the , last clicking
key to enter the following figure for work piece processing:

17
 5.4 Simple Arc
When using a milling machine to process parts, arcs are often processed. Using
the arc calculation function can quickly and easily meet the operator's requirements.
Enter the correct data of the corresponding function as shown in the figure, and
then press Run to enter the operation processing interface.
First clicking F6 to select simple Arc, second clicking the , last clicking
key to enter the following figure for work piece processing:

18
 5.5 Bevel machining
In the daily machining process, it is often necessary to machine the hypotenuse
on the work piece. The automatic calculation function of bevel processing greatly
improves the efficiency of processing with extremely simple operation. Enter the
corresponding data of the corresponding function as shown in the figure, and then
press Run to enter the operation processing interface.
First clicking F6 to select Bevel Machining, second clicking the ,last clicking
key to enter the following figure for work piece processing:

19
 5.6 Network minute Hole
It is convenient and fast to use the network hole processing function to process
the network holes pattern shown in the figure below. Enter the data corresponding
to the corresponding function, and then press Run to enter the operation processing
interface.
First clicking F6 to select Network Hole, second clicking the , last
clicking key to enter the following figure for work piece processing:

20
 5.7 Inner cavity processing
It is convenient and fast to use the rectangular cavity processing function to
process the rectangular figure shown in the figure below. Enter the corresponding
data of the corresponding function, and then press Run to enter the operation
processing interface.
First clicking F6 to select Inner Machining, second clicking the , last
clicking key to enter the following figure for work piece processing:

21
 5.8 EDM
This function is used for the special processing of spark machine (EDM electric
discharge machine). When the target value set by the Z axis of the spark machine is
equal to the current value, the digital display meter outputs a switch signal to control the
stop depth of the spark machine. Input the corresponding function of Correspond to the
data, and then press Run to enter the operation processing interface.
First clicking F6 to select EDM, second clicking the , last clicking
key to enter the following figure for work piece processing:

22
 6. Calculator function

:In addition to the general calculations of addition, subtraction,

multiplication, and division, the calculation also have common trigonometric functions,
including sin, cos, tan, and inverse trigonometric functions, including arcsin, arccos,
arctan, and square functions. It is used in the same way as a general calculator.

7. Appendix

7.1 Fault inspection and treatment

The following troubleshooting is only a preliminary solution. If you still have
problems, please do not remove it by yourself. Please contact the company or the
corresponding agent in time.

23
Failure phenomenon Cause of the malfunction Troubleshooting

1.Whether the power is on? 1. Check if the power cord

2.Is the power switch on? and power plug are plugged
3.Is the power supply in properly.
DRO not show voltage appropriate? 2. Turn off the power switch.
4.Internal short circuit of the 3. The power supply voltage
grating. should be between 85V-265V.
4. Turn off the grating switch.

1. After adjusting with the 1. If this is still counting,the

grating of the other axis, is it failure is grating, if the count
On one axis , DRO still not counting? is not normal, the failure is
has not counted 2. Is the DRO in some DRO.
special function? 2. Exit special function and
try again.

1. The grating is not 1. Reinstall the grating and

installed properly and the well place it on the ground.
Grating is inaccurate accuracy is not enough. 2.Tighten all fixing screws.
counting (cannot be 2. Long-term use, loosening 3.Maintenance of machine
reset to zero) of the fixed reading head tools.
of grating screw caused by 4. Reset the DRO resolution.
machine vibration.
3. The machine tool has
poor accuracy.
4. The DRO does not match
the resolution of the grating.

1. Whether the machine 1. The machine tool and the

DRO counting tool and DRO case are well case of DRO must be well
errors, the display placed on the ground. placed on the ground.
operating distance 2. The accuracy of the 2. Maintenance of machine
and the actual machine tool is poor. tools.
distance does not 3. Machine tool equipment 3. Reduce machine speed.
meet. runs too fast.

24
 4. The grating is not 4. Reinstall the grating and
installed properly and the well place it on the ground.
DRO counting accuracy is not enough. 5. Reset the DRO resolution
errors, the display 5. The resolution of DRO to convert metric and inch
operating distance does not match the grating. display.
and the actual 6. The unit of operation size 6. Reset DRO non-linear error
distance does not does not match the metric compensation.
meet. and inch display. 7. Maintenance grating .
7. Improper setting of linear
error compensation for DRO.

1. The grating is beyond

the applicable range of the
length, and the reading head
is damaged.
2. The grating reading head
rubs its body, causing aluminum
The Grating is not debris to accumulate. Maintenance grating
counting. 3. The gap between grating
reading head and its body is
too large.
4. The grating device or
circuit is damaged, causing a
short circuit or an open circuit.

1. The pulley of grating is

separated from the steel ball.
2. Grating reading head rub
The grating glass.
Sometimes doesn't 3. There is dirt on the grating Maintenance grating
count. glass inside the grating.
4. The pulley wire of
grating reading head is not
flexible enough.

25
 7.2 Instructions for use:
(1). DRO must be handled with care.
(2). The case of DRO must be well placed on the ground.
(3). Voltage range: AC86V ~ 240V 50HZ ~ 60HZ
(4). Power consumption: 15VA
(5). Working temperature: 0 ℃ ~ 50 ℃
(6). Storage temperature: -20 ℃ ~ 65 ℃
(7). Frequency multiplier: 4X

7.3 Interface description

7.4 Sets of DRO

(1). One quantity table
(2). One power cord
(3). One instruction manual
(4). One protective cover
(5). One accessory

7.5 Maintaining
(1). The grating ruler should be kept as clean as possible during the use of the
scale, and the protection against cutting should be done well.
(2). Add a protective cover to the outside of the grating scale as much as possible,
and clean up the chips and oil splashed on the scale in time, and strictly prevent any
dust or splashes from entering the inside of the grating scale shell.
(3). Regularly check whether the mounting and connecting screws are loose,
especially the screws that fix the reading head. Otherwise, the linear axis of the machine
tool may run away or the reference point cannot be returned due to the loosening of the
fixing screw of the reading head.

26
 (4). In order to ensure the reliability of the grating sensor, the grating surface
and the indicating grating surface can be cleaned and wiped with absolute ethanol
at regular intervals to keep the glass grating surface clean.
(5). Violent vibration and beating of the grating ruler are strictly prohibited,
so as not to damage the grating ruler. If the grating ruler is broken, the grating
sensor will lose its effect.
(6). When installing the grating ruler and reading head, pay special attention
to the distance between the reading head and the grating ruler, or the distance
between the reading head and the grating ruler may cause damage to the reading
head or damage to the scale in the housing of the grating ruler, or even scrap the
grating ruler.
(7). Do not disassemble the grating sensor, and do not arbitrarily change the
relative distance between the grating scale and the auxiliary scale. Otherwise, on
the one hand, it may destroy the progress of the grating sensor, and on the other
hand, it may cause the relative friction between the grating scale and the auxiliary
scale, and damage the grating. line, thus causing the grating ruler to be scrapped.
(8). The grating sensor should try to avoid working in an environment with
severe corrosion, so as to avoid corroding the cladding layer and the surface of the
grating scale, and destroying the quality of the grating scale.

8. FAQ
(1). Q: Do you customize order, Such as need 250mm x 550mm x 400mm
(10x22x16)
A: Yes, we accept custom, please contact customer service
([email protected]) for more details!

(2). Q: I have a klutch mini mill (x2), which kit would i need fit xyz axis?
A: You would need the effective travel lengths of the scales to match the
effective travel length of the X and Z axis of the machine. If you have enough room
to mount the scales, you can choose the scales a little longer.

27
(3). Q: Can I cut the scales to fit my mill?
A: We dont suggest you to cut the scales by yourself.

(4). Q: Are the travel dimensions provided actually in the order of X, Y, and Z ?
A: Yes, the length we present in title is travel length .The overall length will be
140mm longer than travel .

9. Disclaimer
(1). The pictures of this product are all taken in kind. Due to the influence of
light and angle during the shooting process, there will be a color difference in the
resolution. The products of distribution channels in different regions will be slightly
different, and the products displayed in the mall shall prevail.

(2). The manufacturer's packaging pattern will be changed without notice, and the
pictures of the mall will be updated as much as possible to ensure the latest product types.

(3). During the use of this product, please work safely.

(4). The internal circuits and components of this product are prohibited from being
disassembled without permission. If you replace the components that are not of our company,
resulting in damage to the product or other accidents, we will not be responsible.

(5). For the products sold, under the compliant operation process, we are only
responsible for the quality of the purchased products themselves. When repairing or
replacing, once the manufacturer confirms other losses and injuries caused by non-
quality problems, the company will is not responsible.

(6). Necessary expertise and advice from others. We strongly recommend that all
purchasers must learn the basics of proper use of the machine and then operate it
under the personal guidance of an experienced operator.

28
 (7). When choosing a workplace, it must be a safe area. The company does not
assume any responsibility for any personal behavior that violates the regulations.

(8). This product has legal patent certification. Without the written consent of the
manufacturer and sales agent, no one may use the sample product for other
commercial channels. Do not use it for political, religious, military or other special
and illegal purposes.

(9). As a compliant manufacturer, our design, manufacture and sales are not
mixed with any political, military, religious, national, race, color propaganda
meaning. What manufacturers can do is to respect scientific, historical rules as
much as possible. The purpose of the manufacturer is for the peace of mankind.

(10). Other matters not covered shall be implemented in accordance with relevant
national laws and regulations!

This product is not to be thrown into the garbage

and complies with EU directives.
2012/19/EU, electronic equipment must be
collected at the end of its useful life and returned
to an authorised recycling facility.

29
Warranty Terms:
1.The table for feedback from customers should be returned to our company
within a month after the date of purchase.In this way,customers may enjoy one-
month repair warranty.
2.Repair Warranty and Purchase Certificate should be presented.The warranty
only applies when all the required documents are available.
3.The warranty does not apply when the equipment has received damage
through abuse,carelessness,improper installation,accident or mishandling
during shipment,connecting to improper line voltage,or has been serviced by
anyone other than an authorized factory representative.
4.After the warranty period,we are ready to provide charged repair
service,perfect as always.

Dear Sir / Madam:

Thank you for purchasing our products.' To improve our service and ensure the
proper use of our products,please kindly write down your suggestions.
Name of Product:
Date of Purchase:
Your Suggestions:
Package:
Functions:
Others:
Date :

GUARANTEE CARD GUARANTEE CARD

The warranty is valid in one year since
the purchase of this ,any quality problem
found,please send back to us with courier fee
The product conforms to the technical standards to be collected,upon receipt of the returning
unit,we will repair it and send back to
QC. customer within two working days.

Manufacture Date Notice:Please enclose the warranty card along

with the returning product, or else we have
the right to reject the repairing,thanks for your
Fast To Buy Limited corporation.

30
 Customer Service Instruction Videos

Fast To Buy Limited

Address: #5009, 5F, Shenzhou Chengyun Building, Bantian Subdistrict,
Longgang District, Shenzhen City,518000, Guangdong, China      
Web: www.toautotool.com
Tel: +86-755-82550561
Email: [email protected]
Facebook: https://www.facebook.com/ToAutoMetalStudio