SIMATIC IOT2020, SIMATIC IOT2040

Preface

Overview 1

Safety instructions 2
Installing and connecting
the device 3
SIMATIC IOT
SIMATIC IOT2020, SIMATIC Software and
4
commissioning
IOT2040
Expand device 5
Operating Instructions
Maintaining and repairing
the device 6

Technical specifications 7

Technical support 8

List of abbreviations A

07/2022
A5E37656492-AC
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens AG A5E37656492-AC Copyright © Siemens AG 2022.

Digital Industries Ⓟ 07/2022 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Preface

These operating instructions contain all the information you need for commissioning and
operation of a device in the SIMATIC IOT2000 family.
It is intended both for programming and testing personnel who commission the device and
connect it with other units (automation systems, programming devices), as well as for service
and maintenance personnel who install add-ons or carry out fault/error analyses.

Basic knowledge requirements

Knowledge of personal computers, operating systems and programming is required to
understand this manual. General knowledge in the field automation control engineering is
recommended.

Scope of validity of this document

These operating instructions apply to the following devices of the device family SIMATIC
IOT2000:
• SIMATIC IOT2020
• SIMATIC IOT2040

Scope of this documentation

The device documentation comprises:
• Product information, e.g. "Important notes on your device"
• Quick Install Guide SIMATIC IOT2000
• SIMATIC IOT2000 operating instructions in German and English

Conventions
The following generic terms are used in this documentation:

Generic term Specific name

Device SIMATIC IOT2020, SIMATIC IOT2040
Arduino shield ARDUINO UNO (Rev3)

The term "device" is also used in place of the product designations SIMATIC IOT2020 and
SIMATIC IOT2040.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 3
Preface

Figures
This manual contains figures of the described devices. The supplied device may differ in some
details from the figures. Within some of the figures, one device is used to represent all
devices.

History
The following editions of these operating instructions have been published:

Edition Comment
09/2016 First edition
10/2016 Second edition, correction to forum login in the section "Software and commissioning"
07/2022 Description of approvals UKCA added

SIMATIC IOT2020, SIMATIC IOT2040

4 Operating Instructions, 07/2022, A5E37656492-AC
Table of contents

Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................ 7
1.1 Product description .............................................................................................................. 7
1.2 Structure of the devices ....................................................................................................... 8
1.2.1 SIMATIC IOT2020 ................................................................................................................. 8
1.2.2 SIMATIC IOT2040 ................................................................................................................. 9
1.3 Accessories ........................................................................................................................ 10
2 Safety instructions ............................................................................................................................... 11
2.1 Security information .......................................................................................................... 11
2.2 General safety instructions ................................................................................................. 11
2.3 Notes on use ..................................................................................................................... 14
3 Installing and connecting the device .................................................................................................. 15
3.1 Preparing for installation .................................................................................................... 15
3.1.1 Checking the delivery......................................................................................................... 15
3.1.2 Identification data of the device ......................................................................................... 17
3.1.3 Permitted mounting positions and mounting types ............................................................ 17
3.2 Mounting the device .......................................................................................................... 18
3.2.1 Mounting instructions ........................................................................................................ 18
3.2.2 Mounting on DIN rails ........................................................................................................ 20
3.2.3 Wall mounting ................................................................................................................... 21
3.3 Connecting the device ....................................................................................................... 22
3.3.1 Notes on connecting .......................................................................................................... 22
3.3.2 Connecting the power supply............................................................................................. 23
3.3.3 Securing the cables ............................................................................................................ 23
4 Software and commissioning .............................................................................................................. 24
5 Expand device...................................................................................................................................... 25
5.1 Insert Micro SD card ........................................................................................................... 25
5.2 Install Arduino shield ......................................................................................................... 25
5.3 Install Mini PCIe card .......................................................................................................... 27
6 Maintaining and repairing the device ................................................................................................. 29
6.1 Maintenance ..................................................................................................................... 29
6.2 Repair information ............................................................................................................. 29
6.3 Replace the backup battery ................................................................................................ 30
6.4 Recycling and disposal ....................................................................................................... 31
7 Technical specifications ....................................................................................................................... 32

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 5
Table of contents

7.1 Certificates and approvals .................................................................................................. 32

7.2 Directives and declarations ................................................................................................ 34
7.2.1 Notes on CE marking ......................................................................................................... 34
7.2.2 ESD guideline .................................................................................................................... 35
7.3 Dimension drawings .......................................................................................................... 37
7.4 Technical data ................................................................................................................... 38
7.4.1 General technical specifications ......................................................................................... 38
7.4.2 Ambient conditions ........................................................................................................... 40
7.4.3 Power demand of the components..................................................................................... 41
7.4.4 Direct current supply (DC) .................................................................................................. 42
7.5 Hardware descriptions ....................................................................................................... 43
7.5.1 Motherboard ..................................................................................................................... 43
7.5.2 External Interfaces ............................................................................................................. 45
7.5.2.1 Power supply ..................................................................................................................... 45
7.5.2.2 USB ................................................................................................................................... 45
7.5.2.3 Ethernet port ..................................................................................................................... 46
7.5.2.4 Serial port (only SIMATIC IOT2040) .................................................................................... 46
7.5.3 Internal interfaces.............................................................................................................. 47
7.5.3.1 Arduino shield interfaces ................................................................................................... 47
7.5.3.2 UART Debug ...................................................................................................................... 49
7.5.3.3 Mini PCIe interface ............................................................................................................. 49
7.5.3.4 Micro SD interface ............................................................................................................. 50
8 Technical support ................................................................................................................................ 51
8.1 Service and support ................................................................ Error! Bookmark not defined.
A List of abbreviations ............................................................................................................................ 52
Glossary ............................................................................................................................................... 54
Index .................................................................................................................................................... 56

SIMATIC IOT2020, SIMATIC IOT2040

6 Operating Instructions, 07/2022, A5E37656492-AC
Overview 1
1.1 Product description
The devices of the SIMATIC IOT family offer a robust, compact and flexible solution with a
focus on the IOT environment and round off the SIMATIC IPC product range in the lower
output range.

Features
• High degree of ruggedness
• Compact design as per LOGO!
• External RS232/RS422/RS485, Ethernet and USB interfaces
• Internal interfaces for Arduino Shield and Mini PCIe card
• Freely programmable interfaces
• Maintenance-free operation possible

Features
Depending on the industrial area of application, the following SIMATIC IOT devices are
available with the following features:

SIMATIC IOT2040
• Intel Quark X1020 processor
• 1 GB RAM
• 2 x Ethernet interfaces

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 7
Overview
1.2 Structure of the devices

• 2 x RS232/422/485 interface
• Battery-buffered real-time clock

SIMATIC IOT2020
• Intel Quark X1000 processor
• 512 MB RAM
• 1 x Ethernet interface

1.2 Structure of the devices

1.2.1 SIMATIC IOT2020

The following figures show the configuration and interfaces of the SIMATIC IOT2020.

Top view

Front view

Bottom view

SIMATIC IOT2020, SIMATIC IOT2040

8 Operating Instructions, 07/2022, A5E37656492-AC
 Overview
1.2 Structure of the devices

① Openings for push-in lugs for wall mounting ⑦ Securing device

② Markings for the installation of antennae ⑧ RESET button for the CPU
③ Power supply connector ⑨ USER button, programmable
④ LED display, see section "Motherboard (Page 43)" ⑩ Ethernet interface
10/100 Mbps
⑤ Cover on left ⑪ USB Type Micro B
⑥ Cover on right ⑫ USB Type A

1.2.2 SIMATIC IOT2040

The following figures show the configuration and interfaces of the SIMATIC IOT2040.

Top view

Front view

Bottom view

iot2040_aufbau

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 9
Overview
1.3 Accessories

① Openings for push-in lugs for wall mounting ⑧ Securing device

② Markings for the installation of antennae ⑨ RESET button for the CPU
③ Power supply connector ⑩ USER button, programmable
④ COM interfaces (RS232/422/485) ⑪ Ethernet interface
10/100 Mbps
⑤ LED display, see section "Motherboard (Page 43)" ⑫ Ethernet interface
10/100 Mbps, prepared for PoE
⑥ Cover on left ⑬ USB Type Micro B
⑦ Cover on right ⑭ USB Type A

1.3 Accessories
This chapter contains the scope of accessories valid at the time these operating instructions
were written. The following accessories are not included in the scope of delivery and can be
ordered separately. Additional accessories can be found on the Internet at:
AUTOHOTSPOT

Push-in lugs

Set with 100 push-in lugs for wall mounting

Article number: 3RB1900-0B

Storage media
SIMATIC PC USB flash drive
Article number: 6ES7648-0DC50-0AA0, 6ES7648-0DC60-0AA0

SIMATIC IOT2020, SIMATIC IOT2040

10 Operating Instructions, 07/2022, A5E37656492-AC
Safety instructions 2
2.1 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/cert).

2.2 General safety instructions

WARNING
Life-threatening voltages are present with an open control cabinet
When you install the device in a control cabinet, some areas or components in the open
control cabinet may be carrying life-threatening voltages.
If you touch these areas or components, you may be killed by electric shock.
Switch off the power supply to the cabinet before opening it.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 11
Safety instructions
2.2 General safety instructions

System expansions

NOTICE
Damage through system expansions
Device and system expansions may be faulty and can affect the entire machine or plant.
The installation of expansions can damage the device, machine or plant. Device and system
expansions may violate safety rules and regulations regarding radio interference
suppression. If you install or exchange system expansions and damage your device, the
warranty becomes void.

For system expansions:

• Only install system expansion devices designed for this device. Contact your technical
support team or where you purchased your PC to find out which system expansion devices
may safely be installed.
• Observe the information on electromagnetic compatibility (Page 38).

WARNING
Risk of fire through expansion cards
Expansion cards generate additional heat. The device may overheat and cause a fire.
Please note the following:
• Observe the safety and installation instructions for the expansion cards.
• If in doubt, install the device in an enclosure that is compliant with sections 4.6 and
4.7.3 of the IEC/UL/EN/DIN-EN 60950-1 standard.

NOTICE
Use in the scope of application for the UL61010-2-201
When the device is used in the area of Industrial Control Equipment in accordance with
UL61010-2-201, note that the device is classified as "Open Type". A UL61010-2-201
conform enclosure is therefore a mandatory requirement for approval or operation
according to UL61010-2-201.
If the device is used in a manner not specified by the manufacturer, the approval is lost and
the protection associated with it may be impaired.

SIMATIC IOT2020, SIMATIC IOT2040

12 Operating Instructions, 07/2022, A5E37656492-AC
 Safety instructions
2.2 General safety instructions

Note
Limitation of liability
All technical specifications and approvals of the device only apply if you use expansion
components that have a valid CE approval (CE mark). The installation conditions for
expansion components in the associated documentation must be observed.
UL approval of the device only applies when the UL-approved components are used according
to their "Conditions of Acceptability".
We are not liable for functional limitations caused by the use of third-party devices or
components.

NOTICE
The approvals are voided if certain modifications are made
The device approvals are voided if the following modifications are made:
• The enclosure was physically modified, for example, openings were created to make
LEDs on a plug-in card in the device visible.
• Cables are routed from the inside out of the device or from the outside into the device,
for example, to connect sensors or displays.

Battery and rechargeable battery

WARNING
Risk of explosion and release of harmful substances
Improper handling of lithium batteries can result in an explosion of the batteries.
Explosion of the batteries and the released pollutants can cause severe physical injury. Worn
batteries jeopardize the function of the device.
Note the following when handling lithium batteries:
• Replace used batteries in good time; see the section "Replacing the backup battery" in
the operating instructions.
• Replace the lithium battery only with an identical battery or types recommended by the
manufacturer (order no.: A5E34734290).
• Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge,
do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and
protect from direct sunlight, moisture and condensation.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 13
Safety instructions
2.3 Notes on use

Strong high-frequency radiation

NOTICE
Observe immunity to RF radiation
The device has an increased immunity to RF radiation according to the specifications on
electromagnetic compatibility in the technical specifications.
Radiation exposure in excess of the specified immunity limits can impair device functions,
result in malfunctions and therefore injuries or damages.
Read the information on immunity to RF radiation in the technical specifications.

ESD Guideline
Electrostatic sensitive devices can be labeled with an appropriate symbol.

NOTICE
Electrostatic sensitive devices (ESD)
When you touch electrostatic sensitive components, you can destroy them through voltages
that are far below the human perception threshold.
If you work with components that can be destroyed by electrostatic discharge, observe the
ESD Guideline.

2.3 Notes on use

NOTICE
Possible functional restrictions in case of non-validated plant operation
The device is tested and certified on the basis of the technical standards. In rare cases,
functional restrictions can occur during plant operation.
Validate the correct functioning of the plant to avoid functional restrictions.

Note
Use in an industrial environment without additional protective measures
This device was designed for use in a normal industrial environment according to IEC 60721-
3-3.

SIMATIC IOT2020, SIMATIC IOT2040

14 Operating Instructions, 07/2022, A5E37656492-AC
Installing and connecting the device 3
3.1 Preparing for installation

3.1.1 Checking the delivery

Procedure
1. When accepting a delivery, please check the packaging for visible transport damage.
2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping
company in charge. Have the shipper confirm the transport damage immediately.
3. Unpack the device at its installation location.
4. Keep the original packaging in case you have to transport the unit again.

Note
Damage to the device during transport and storage
If a device is transported or stored without packaging, shocks, vibrations, pressure and
moisture may impact the unprotected unit. A damaged packaging indicates that ambient
conditions have already had a massive impact on the device.
The device may be damaged.
Do not dispose of the original packaging. Pack the device during transportation and
storage.

5. Check the contents of the packaging and any accessories you may have ordered for
completeness and damage.
– Device
– DC connecting terminal, already plugged into the device.
– Inserts

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 15
Installing and connecting the device
3.1 Preparing for installation

6. If the contents of the packaging are incomplete, damaged or do not match your order,
inform the responsible delivery service immediately.

WARNING
Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or
plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.
Make sure that the damaged device is not inadvertently installed and put into operation.
Label the damaged device and keep it locked away. Send off the device for immediate
repair.

NOTICE
Damage from condensation
If the device is subjected to low temperatures or extreme fluctuations in temperature
during transportation, for example in cold weather, moisture could build up on or inside
the HMI device (condensation).
Moisture causes a short circuit in electrical circuits and damages the device.
In order to prevent damage to the device, proceed as follows:
• Store the device in a dry place.
• Bring the device to room temperature before starting it up.
• Do not expose the device to direct heat radiation from a heating device.
• If condensation develops, wait approximately 12 hours or until the device is
completely dry before switching it on.

7. Please keep the enclosed documentation in a safe place. It belongs to the device. You need
the documentation when you commission the device for the first time.
8. Write down the identification data of the device.

SIMATIC IOT2020, SIMATIC IOT2040

16 Operating Instructions, 07/2022, A5E37656492-AC
 Installing and connecting the device
3.1 Preparing for installation

3.1.2 Identification data of the device

The device can be clearly identified with the help of this identification data in case of repairs
or theft.
You can find this information on the rating plate. The following illustration shows an
example.

Example rating plate: Enter the identification data in the table below:
Order number 6ES ...
Serial number S VP
Production version FS
All existing Ethernet ad-
dresses (MAC)

3.1.3 Permitted mounting positions and mounting types

The device can be attached horizontally or vertically on a DIN rail or to a wall.

Horizontal mounting position, preferred Vertical mounting position

Take into account the permitted temperature range for operation that depends on the
mounting position in accordance with the "Technical specifications (Page 38)" section.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 17
Installing and connecting the device
3.2 Mounting the device

Clearances
Ensure that the following clearances measurements to another component or to a wall of a
housing are complied with:
• Below the device: ≥ 50 mm
• Above the device: ≥ 50 mm

3.2 Mounting the device

3.2.1 Mounting instructions

Note the following:
• The device is approved for operation in closed rooms only.
• For installation in a cabinet, observe the SIMATIC setup guidelines as well as the relevant
DIN/VDE requirements or the applicable country-specific regulations.
• When the device is used in the area of Industrial Control Equipment in accordance with
UL61010-2-201, note that the device is classified as "Open Type". A UL61010-2-201
conform enclosure is therefore a mandatory requirement for approval or operation
according to UL61010-2-201.
• Install all the expansions in the device before mounting the device on a DIN rail or a wall,
see section "Expand device (Page 25)".
• To protect the enclosure of the device against unauthorized opening, after installing the
expansions you can screw the rear panel of the enclosure to the front panel of the
enclosure using two screws. The screws are not included in the scope of delivery. Use only

SIMATIC IOT2020, SIMATIC IOT2040

18 Operating Instructions, 07/2022, A5E37656492-AC
 Installing and connecting the device
3.2 Mounting the device

screws of the type WN1452-K30x20-ST-A2F and tighten the screws using a torque of
0.5 Nm.

Fasten securely

NOTICE
Insufficient load carrying capacity
If the mounting surface for wall mounting does not have a sufficient load-bearing capacity,
the device may fall and be damaged.
Ensure that the mounting surface on the wall can bear four times the total weight of the
device, including fixing elements.

NOTICE
Incorrect fixing elements
If you use anchors and screws other than those specified below for wall mounting, safe
mounting is not guaranteed. The device can fall and may be damaged.
Use only the anchors and screws specified in the following table.

Material Bore diameter Fixing element

Concrete Select according to the specifi- • Anchor, ∅ 6 mm, 40 mm long
cation of the mounting ele-
ments used • Screw, ∅ 4-5 mm, 40 mm long
Plasterboard, Toggle plug, ∅ 12 mm, 50 mm
(at least 13 mm thick) long
Metal, • Screw M4 × 15
(at least 2 mm thick)
• M4 nut

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 19
Installing and connecting the device
3.2 Mounting the device

3.2.2 Mounting on DIN rails

Requirement
• A DIN rail, 35 mm standard profile
The DIN rail is installed at the installation site.

Procedure

Mounting

1. Place the device and rail clip on the upper

edge of the standard profile rail at the
position shown and push the device down.
2. Swing the rail clips of the device from below
via the standard profile rail.
3. Push the device in the direction of the
standard profile rail. You will hear the device
click into place.

Removing
1. Push down the device until it is released by the rail clips.
2. Swing the device out of the standard profile rail.
3. Lift the device up and off.

SIMATIC IOT2020, SIMATIC IOT2040

20 Operating Instructions, 07/2022, A5E37656492-AC
 Installing and connecting the device
3.2 Mounting the device

3.2.3 Wall mounting

The device is suitable for horizontal or vertical wall mounting.

Requirement
• Four push-in lugs
The push-in lugs must be ordered separately, see section "Accessories (Page 10)"
• Four anchors and four screws

Procedure for mounting

1. Guide a push-in lug

through the
corresponding opening at
the top of the device, as
shown

2. Press the push-in lug

down.

3. Mark the bore holes, drill

the required holes in the
wall and fasten the device
to the wall using four
screws and corresponding
anchors.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 21
Installing and connecting the device
3.3 Connecting the device

3.3 Connecting the device

3.3.1 Notes on connecting

WARNING
Risk of lightning strikes
A lightning flash may enter the mains cables and data transmission cables and jump to a
person.
Death, serious injury and burns can be caused by lightning.
Take the following precautions:
• Disconnect the device from the power supply in good time when a thunderstorm is
approaching.
• Do not touch mains cables and data transmission cables during a thunderstorm.
• Keep a sufficient distance from electric cables, distributors, systems, etc.

NOTICE
Fault caused by I/O devices
The connection of I/O devices can cause faults in the device.
The result may be personal injury and damage to the machine or plant.
Note the following when connecting I/O devices:
• Read the documentation of the I/O devices. Follow all instructions in the documentation.
• Only connect I/O devices which are approved for industrial applications in accordance
with EN 61000-6-2 and IEC 61000-6-2.
• I/O devices that are not hotplug-capable may only be connected after the device has
been disconnected from the power supply.

NOTICE
Damage through regenerative feedback
Regenerative feedback of voltage to ground by a connected or installed component can
damage the device.
Connected or built-in I/Os, for example, a USB drive, are not permitted to supply any voltage
to the device. Regenerative feedback is generally not permitted.

NOTICE
Ferrite required at USB cables
The interference immunity of the device according to the data in the technical specifications
is only guaranteed when the cables at USB and micro USB ports are equipped with a ferrite
magnet. Use only USB cables equipped with a ferrite magnet.

SIMATIC IOT2020, SIMATIC IOT2040

22 Operating Instructions, 07/2022, A5E37656492-AC
 Installing and connecting the device
3.3 Connecting the device

3.3.2 Connecting the power supply

Note
The device should only be connected to a 9...36 V DC power supply which meets the
requirements of safe extra low voltage (SELV) according to IEC/EN/DIN EN/UL 60950-1.
The power supply must meet the requirement NEC Class 2 or LPS according to IEC/EN/DIN
EN/UL 60950-1.

Note
The power supply must be adapted to the input data of the device, see chapter "General
technical specifications (Page 38)".
If there are voltage peaks on power supply lines, use a protective device in the form of a
varistor (MOV) UMOV = U-rated x 1.2 (BLITZDUCTOR BVT AVD 24 (918 422) or compatible).

Requirement
• You are using the supplied terminal.
• A two-core cable with a cable cross-section of 0.75 mm2 to 2.5 mm2.
• A slotted screwdriver with a 3mm blade.

Procedure

1. Switch off the power supply.

2. Connect the lines to the connecting
terminal as shown.
3. Connect the connecting terminal to the
connection for the power supply.

3.3.3 Securing the cables

Use cable ties or cable clamps to secure the connected cables to suitable fixing elements for
strain relief.
Make sure that the cables are not crushed by the cable tie or the cable clamps.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 23
Software and commissioning 4
Operating system and software for the SIMATIC IOT devices are freely programmable and are
downloaded from the Micro SD card when the device is booted.
For SIMATIC IOT2040: The device starts with "Secure Boot", which means the SD card with the
customer-specific image must be signed accordingly.
Additional information on the topics software, "Secure Boot", commissioning and Micro SD
image is available in the SIMATIC IOT2000 Forum.

SIMATIC IOT2000 Forum

To use the SIMATIC IOT2000 Forum, you need a login for online support.
Follow these steps to participate in the Technical Forum:
1. Open the website "Technical Forum".
2. If you do not yet have a login for online support, click "Register" at the top right of the
window and follow the registration instructions.

During registration, you enter an alias for the forum, for example. This alias is the
pseudonym under which other users can see you and talk to you in the forum.
You will receive a confirmation e-mail after registering successfully.

SIMATIC IOT2020, SIMATIC IOT2040

24 Operating Instructions, 07/2022, A5E37656492-AC
Expand device 5
5.1 Insert Micro SD card

Requirement
• The device is disconnected from the power supply.
• Micro SD card that is suitable for industrial use.

Procedure

Installation

NOTICE
Inserting a memory card
If you are using the Micro SD card in a device installed in a system, you must observe the
safety regulations for work on electrical systems.
Carefully insert the Micro SD card into the Micro SD holder without applying excess force.

1. Open the cover on the right.

2. Carefully press the Micro SD holder down
and lift the holder forwards.
3. Push the Micro SD card correctly aligned
into the supporting frame. The contacts
of the Micro SD card must point in the
direction of the motherboard.
4. Push the supporting frame back and
carefully push the supporting frame
upwards until it engages.

5.2 Install Arduino shield

Requirement
• The device is disconnected from the power supply.
• An Arduino shield

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 25
Expand device
5.2 Install Arduino shield

Procedure

NOTICE
Install Arduino shield
Do not under any circumstances insert the Arduino shield incorrectly. Ensure that the
contact pins of the Arduino shield connect correctly with the terminal strips of the
motherboard.
Arduino shield with operator control or display elements
Some Arduino shields have operator control and display elements. The device loses its
approval certificates if you drill or mill openings in the cover in order to make the operator
control or display elements of the Arduino shield accessible or visible from outside. In this
case, the customer is responsible for the re-approval of the device.

Note
Power consumption
If the power consumption of the Arduino shield is too high, the device will be damaged.
Note the information in section "Technical data (Page 38)".
Ambient temperature
The temperature in the housing of the device can be up to 30 °C above the maximum
permissible ambient temperature of the device.
Make sure that the maximum permissible ambient temperature of the Arduino shield is
specified accordingly.

1. Open cover on the right and lift up the cover.

2. Open the cover on the left by slighting raising the cover and lifting it to the left.
3. Insert the Arduino shield into the motherboard Ensure that the contact pins of the Arduino
shield fit perfectly on the contact strips of the motherboard and that the components of the
Arduino shield do not touch the components of the motherboard.

SIMATIC IOT2020, SIMATIC IOT2040

26 Operating Instructions, 07/2022, A5E37656492-AC
 Expand device
5.3 Install Mini PCIe card

Note
Only use fixing elements made from plastic.
You can use the four boreholes in the motherboard to additionally fasten the Arduino shield
on the motherboard. Two of the boreholes are shown in the figure above. Use only fixing
elements made from plastic, not metallic or conductive materials.

5.3 Install Mini PCIe card

You can install a Mini PCIe card in a device of the type IOT2000.

Note
Power consumption
If the power consumption of the Mini PCIe card is too high, the device will be damaged.
Note the information in section "Technical data (Page 38)".
Ambient temperature
The temperature in the housing of the device can be up to 30 °C above the maximum
permissible ambient temperature of the device.
Make sure that the maximum permissible ambient temperature of the Mini PCIe- card is
specified accordingly.

Requirement
• The device is disconnected from the power supply.
• A Mini PCIe card

CAUTION
Risk of burns due to hot components
The motherboard and internal components can get hot during operation. Motherboard and
internal components will only cool down slowly after the device has been switched off.
To avoid getting burned, wait a while after switching off the power supply. Be very careful
when opening the enclosure and removing the motherboard.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 27
Expand device
5.3 Install Mini PCIe card

Procedure
The following example describes the installation of a Mini PCIe WLAN card, including
mounting of the antenna jacks. If you install a different Mini PCIe card, the work steps 4, 5
and 7 are not required.

When the enclosure is secured with two

screws at the rear panel, remove the two
screws.
Remove the battery, see section "Replace
the backup battery (Page 30)".
Then follow these steps:
1. Loosen the front panel of the housing
from the rear panel of the housing.
Carefully press with the blade of a flat-
blade screwdriver in the marked
recesses and carefully pull on the
appropriate place on the front panel of
the enclosure.
2. Remove the front panel of the
enclosure.
3. Remove the motherboard.
4. Drill the bushings for the antenna
sockets with a corresponding diameter
at the markings shown.
5. Install the antenna sockets in the
enclosure.
6. Insert the Mini PCIe card in the Mini
PCIe interface on the motherboard
from below as illustrated.
7. Connect the antenna cables to the Mini
PCIe card.

Then install the motherboard again and close the housing.

SIMATIC IOT2020, SIMATIC IOT2040

28 Operating Instructions, 07/2022, A5E37656492-AC
Maintaining and repairing the device 6
6.1 Maintenance
To retain a high level of system availability, or devices with a back-up battery, we recommend
the preventative replacement of the back-up battery at replacement intervals of 5 years.

6.2 Repair information

Carrying out repairs

Only qualified personnel are permitted to repair the device. Contact your local representative,
see section "AUTOHOTSPOT".

WARNING
Unauthorized opening and improper repairs on the device may result in substantial
damage to equipment or endanger the user.
• Always disconnect the power plug before you open the device.
• Only install system expansion devices designed for this device. If you install other
expansion devices, you may damage the device or violate the safety requirements and
regulations on RF suppression. Contact your technical support team or where you
purchased your PC to find out which system expansion devices may safely be installed.

If you install or exchange system expansions and damage your device, the warranty
becomes void.

CAUTION
Electrostatic sensitive devices (ESD)
The device contains electronic components which are destroyed by electrostatic charges.
This can result in malfunctions and damage to the machine or plant.
Make sure you take precautionary measures even when you open the device, for example,
when opening device doors, device covers or the housing cover. For more information, refer
to the chapter "ESD Guideline"

Limitation of liability
All technical specifications and approvals of the device only apply if you use expansion
components that have a valid CE approval (CE mark). The installation instructions for
expansion components in the associated documentation must be observed.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 29
Maintaining and repairing the device
6.3 Replace the backup battery

UL approval of the device only applies when the UL-approved components are used according
to their "Conditions of Acceptability".
We are not liable for functional limitations caused by the use of third-party devices or
components.

6.3 Replace the backup battery

This chapter applies to the device IOT2040, which has a back-up battery.

Prior to replacement

WARNING
Risk of explosion and release of harmful substances
Improper handling of lithium batteries can result in an explosion of the batteries.
Explosion of the batteries and the released pollutants can cause severe physical injury. Worn
batteries jeopardize the function of the device.
Note the following when handling lithium batteries:
• Replace the battery every 5 years.
• Replace the lithium battery only with the type recommended by the manufacturer.
The article number is A5E34734290.
• Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge,
do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and
protect from direct sunlight, moisture and condensation.

NOTICE
Disposal of batteries and rechargeable batteries
Batteries and rechargeable batteries do not belong in domestic garbage. The user is legally
obliged to return used batteries and rechargeable batteries.
Used batteries and rechargeable batteries pollute the environment as special waste. You as
a user are liable to prosecution if you do not properly dispose of batteries and rechargeable
batteries.
Please observe the following when disposing of batteries and rechargeable batteries:
• Dispose of used batteries and rechargeable batteries separately as hazardous waste in
accordance with local regulations.
• You can return used batteries and rechargeable batteries to public collection points and
wherever batteries or rechargeable batteries of the type in question are sold.
• Label the battery container "Used batteries and rechargeable batteries".

SIMATIC IOT2020, SIMATIC IOT2040

30 Operating Instructions, 07/2022, A5E37656492-AC
 Maintaining and repairing the device
6.4 Recycling and disposal

Requirement
• The device is disconnected from the power supply.
• A replacement battery with the article number A5E34345932 is available.

Procedure

NOTICE
The time is lost after 30 seconds
The time will be deleted if it takes you longer than 30 seconds to replace the battery. The
device is no longer synchronous. Time-controlled programs will no longer run or will run at
the wrong time. This may damage the plant.
Reset the time for the device.

1. Open the cover on the right.

2. Pull the plug of the battery cable

from the motherboard.

3. Remove the battery from the

battery box.

Insert the replacement battery, plug

in the battery cable on the mother-
board and close the cover on the
right.

6.4 Recycling and disposal

Due to the low levels of pollutants in the HMI devices described in these operating
instructions, they can be recycled.
Contact a certified disposal service company for electronic scrap for environmentally sound
recycling and disposal of your old devices, and dispose of the device according to the relevant
regulations in your country.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 31
Technical specifications 7
7.1 Certificates and approvals

NOTICE
The approvals are voided if certain modifications are made
The device approvals are voided if the following modifications are made:
• An Arduino shield or a Mini PCIe card was installed.
• The enclosure was physically modified, for example, openings were created to make
LEDs on a plug-in card in the device visible.
• Cables are routed from the inside out of the device or from the outside into the device,
for example, to connect sensors or displays.

The device meets the guidelines listed in the following sections.

EU Declaration of Conformity
The associated declaration of conformity is available on the Internet at the following address:
AUTOHOTSPOT.

UKCA
The device complies with the designated British standards (BS) for IPC published in the official
consolidated list of the British Government. The device meets the requirements and
protection targets of the following regulations and related amendments:
• Electromagnetic Compatibility Regulations 2016 (EMC)
• Regulations on the restriction of the use of certain hazardous substances in electrical and
electronic equipment 2012 (RoHS).
UK Declarations of Conformity for the respective authorities are available from:
Siemens AG
Digital Industries
Factory Automation
DI FA TI COS TT
P.O. Box 1963
D-92209 Amberg
The UK Declaration of Conformity is also available for download from the Siemens Industry
Online Support website under the keyword "Declaration of Conformity".

SIMATIC IOT2020, SIMATIC IOT2040

32 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.1 Certificates and approvals

ISO 9001 certificate

The Siemens quality management system for our entire product creation process
(development, production and sales) meets the requirements of ISO 9001.
This has been certified by the TÜV Rheinland.

Software license agreements

If the device is supplied with preinstalled software, you must observe the corresponding
license agreements.

UL approval
The following approvals are available for the device:
• Underwriters Laboratories (UL) in accordance with standard UL61010-2-201
(IND.CONT.EQ), File E472609
• Canadian National Standard CAN/CSA-C22.2 No. 142 and CAN/CSA-C22.2 No. 61010-2-
201

FCC and Canada

USA
Federal Communi- This equipment has been tested and found to comply with the limits for a Class A
cations Commis- digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
sion provide reasonable protection against harmful interference when the equipment
Radio Frequency is operated in a commercial environment. This equipment generates, uses, and
Interference can radiate radio frequency energy and, if not installed and used in accordance
Statement with the instruction manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference
at his own expense.
Shielded Cables Shielded cables must be used with this equipment to maintain compliance with
FCC regulations.
Modifications Changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate the equipment.
Conditions of This device complies with Part 15 of the FCC Rules. Operation is subject to the
Operations following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.

CANADA
Canadian Notice This Class A digital apparatus complies with Canadian ICES-003 (A).
Avis Canadien Cet appareil numérique de la classe A est conforme à la norme NMB-
003 (A) du Canada.

RCM AUSTRALIA/NEW ZEALAND

This product meets the requirements of the standard EN 61000-6-4:2007 Generic standards –
Emission standard for industrial environments.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 33
Technical specifications
7.2 Directives and declarations

Identification for Eurasion Customs Union

• EAC (Eurasian Conformity)
• Customs union of Russia, Belarus and Kazakhstan
• Declaration of conformity according to Technical Regulations of the Customs Union (TR
CU)

KOREA
This product satisfies the requirement of the Korean Certification (KC Mark).
이 기기는 업무용(A 급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

WEEE label (European Union)

Disposal instructions, observe the local regulations and the section "Recycling and
disposal (Page 31) ".

7.2 Directives and declarations

7.2.1 Notes on CE marking

Electromagnetic compatibility
This product meets the requirements of EU Directive 2014/30/EU "Electromagnetic
Compatibility".
The device is designed for the following areas of application corresponding to the CE
marking:

Scope of application Requirements for

Interference emission Immunity to interference
Industrial area EN 61000-6-4:2007 EN 61000-6-2:2005
+A1:2011

SIMATIC IOT2020, SIMATIC IOT2040

34 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.2 Directives and declarations

7.2.2 ESD guideline

What does ESD mean?

An electronic module is equipped with highly integrated components. Due to their design,
electronic components are highly sensitive to overvoltage and thus to the discharge of static
electricity. Such electronic components or modules are labeled as electrostatic sensitive
devices.
The following abbreviations are commonly used for electrostatic sensitive devices:
• ESD – Electrostatic sensitive device
• ESD – Electrostatic Sensitive Device as a common international designation
Electrostatic sensitive devices can be labeled with an appropriate symbol.

NOTICE
Damage to ESD from touch
Electrostatic sensitive devices, ESD, can be destroyed by voltages which are far below the
human perception limit. If you touch a component or electrical connections of a module
without discharging any electrostatic energy, these voltages may arise.
The damage to a module by an overvoltage can often not be immediately detected and only
becomes evident after an extended period of operation. The consequences are incalculable
and range from unforeseeable malfunctions to a total failure of the machine or system.
Avoid touching components directly. Make sure that persons, the workstation and the
packaging are properly grounded.

Charge
Every person without a conductive connection to the electrical potential of his/her
surroundings can be electrostatically charged.
The material with which this person comes into contact is of particular significance. The
figure shows the maximum electrostatic voltages with which a person is charged, depending
on humidity and material. These values conform to the specifications of IEC 61000-4-2.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 35
Technical specifications
7.2 Directives and declarations

① Synthetic materials
② Wool
③ Antistatic materials such as wood or concrete

NOTICE
Grounding measures
There is no equipotential bonding without grounding. An electrostatic charge is not
discharged and may damage the ESD.
Protect yourself against discharge of static electricity. When working with electrostatic
sensitive devices, make sure that the person and the workplace are properly grounded.

Protective measures against discharge of static electricity

• Disconnect the power supply before you install or remove modules which are sensitive to
ESD.
• Pay attention to good grounding:
– When handling electrostatical sensitive devices, make sure that persons, the
workstation and devices, tools and packaging used are properly grounded. This way
you avoid static discharge.
• Avoid direct contact:
– As a general rule, do not touch electrostatic sensitive devices, except in the case of
unavoidable maintenance work.
– Hold the modules at their edge so that you do not touch the connector pins or
conductor paths. This way, the discharge energy does not reach and damage the
sensitive components.
– Discharge your body electrostatically before you take a measurement at a module. Do
so by touching grounded metallic parts. Always use grounded measuring instruments.

SIMATIC IOT2020, SIMATIC IOT2040

36 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.3 Dimension drawings

7.3 Dimension drawings

The following figures show the dimension drawings of the type IOT2000.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 37
Technical specifications
7.4 Technical data

7.4 Technical data

7.4.1 General technical specifications

General technical specifications

Article number See order documents

Weight without mounting brackets • SIMATIC IOT2020: approx. 200 g
• SIMATIC IOT2040: approx. 230 g
Power supply 1 DC 9…36 V, no galvanic isolation
Brief voltage interruption in accord- Up to 5 ms buffer time at 24 V DC and full load2
ance with Namur Max. 10 events per hour; recovery time at least 10 s
Current consumption Max. 1.4 A
Noise emission < 40 dB(A) according to DIN 45635-1
Degree of protection IP20 according to IEC 60529
Quality assurance In accordance with ISO 9001
1 The device should only be connected to a power supply which meets the requirements of safe extra
low voltage (SELV) according to IEC/EN/DIN EN/UL 60950-1. The power supply must meet the re-
quirement NEC Class 2 or LPS according to the IEC/EN/DINEN/UL 60950-1.
2 In the event of low supply voltage, the buffer time is reduced

Electromagnetic compatibility

Immunity with regard to conducted ± 2 kV according to IEC 61000-4-4; burst

interference on the supply lines ± 1 kV according to IEC 61000-4-5; asymmetrical surge
Noise immunity on signal lines ± 1 kV according to IEC 61000-4-4; burst; length < 30 m
± 2 kV according to IEC 61000-4-4; burst; length > 30 m
± 2 kV according to IEC 61000-4-5; surge; length > 30 m
Immunity to discharges of static ± 4 kV contact discharge in accordance with IEC 61000-4-2
electricity ± 8 kV air discharge in accordance with IEC 61000-4-2
Immunity to RF interference 10 V/m, 80 MHz to 1 GHz, 80% AM in accordance with
IEC 61000-4-3
3 V/m, 1.4 to 2 GHz, 80% AM in accordance with IEC 61000-4-3
1 V/m, 2 to 2.7 GHz, 80% AM in accordance with IEC 61000-4-3
10 V, 150 KHz to 80 MHz, 80% AM in accordance with IEC
61000-4-6

If there are voltage peaks on power supply lines, use a protective device in the form of a
varistor (MOV) UMOV = U-rated x 1.2 (BLITZDUCTOR BVT AVD 24 (918 422) or compatible).

SIMATIC IOT2020, SIMATIC IOT2040

38 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.4 Technical data

Motherboard

Processor • SIMATIC IOT2020: Intel Quark X1000, 400 MHz

• SIMATIC IOT2040: Intel Quark X1020, 400 MHz
RAM • SIMATIC IOT2020: 512 MB
• SIMATIC IOT2040: 1 GB
BIOS SPI Flash 8 MB
Micro SD Slot for one Micro SD card
Expansion slots 1 x Arduino shield
1 x mini PCIe for PCIe cards 30 x 50.59 mm or 30 x 26.8 mm via
adapter

Interfaces

All devices of the type SIMATIC IOT2000

USB Type A, X60 USB 2.0 host, high current, max. 2.5 W/500 mA
USB Typ Micro B, X61 USB device interface
LAN interface X1 P1, RJ45 1 SOC LAN controller
Additionally with SIMATIC IOT2040
LAN interface X2 P1, RJ45 3 SOC LAN controller
COM X30, X31 • RS 232 2, max. 115 Kbps, D-sub connector, 9-pin
• RS 422 2 3, max. 115 Kbps, D-sub connector, 9-pin
• RS 485 2 3, max. 115 Kbps, D-sub connector, 9-pin
Maximum permitted cable length at the RS 485: 30 m
Maximum permitted cable length at the other COM ports:
1000 m
1 For unique labeling, the LAN interfaces are numbered on the enclosure. The numbering by the
operating system can differ.
2 You can use any COM port as an RS 232, RS422 or RS 485 interface through the software-
controlled interface parameter assignment. Possible parameters: "Auto-flow-control", "Onboard
termination", "Half-duplex" or "Full-duplex"
3 Termination can be set with the software.

Additional information on parameter assignment is available in the SIMATIC IOT2000-Forum,

see section "Software and commissioning (Page 24)".

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 39
Technical specifications
7.4 Technical data

7.4.2 Ambient conditions

Climatic ambient conditions

The temperature values have been checked in accordance with IEC 60068-2-1, IEC 60068-2-2
and IEC 60068-2-14. Permitted mounting positions, see section "Permitted mounting
positions and mounting types (Page 17)“.

Ambient temperature
• Operation 0 … 50 °C *

• Storage/transport -20 ... 70 °C

Gradient
• Operation Max. 10 °C/h

• Storage 20 °C/h, no condensation

Relative humidity, tested in accordance with IEC 60068-2-78, IEC 60068-2-30

• Operation 5 … 85% at 30°C, no condensation

• Storage/transport 5 … 95 % at 25/55 °C, no condensation

Atmospheric pressure
• Operation 1080 … 795 hPa, corresponds to an elevation of -1000 m to 2000 m

• Storage/transport 1080 to 660 hPa, corresponds to an elevation of -1000 to 3500 m

* Also note the following section "Power consumption of the components".

Mechanical ambient conditions

Vibration resistance, tested in accordance with IEC 60068-2-6

• Operation Vibration load 1g, 10 cycles per axle:
• 5 to 8.4 Hz, deflection 3.5 mm
• 8.4 to 200 Hz, acceleration 9.8 m/s2

• Storage/transport • 5 to 8.4 Hz: Deflection 3.5 mm

• 8.4 Hz to 500 Hz: Acceleration 9.8 m/s2
Impact resistance, tested in accordance with IEC 60068-2-27
• Operation 150 m/s2, 11 ms

• Storage/transport 250 m/s2, 6 ms

SIMATIC IOT2020, SIMATIC IOT2040

40 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.4 Technical data

7.4.3 Power demand of the components

Maximum power consumption of the auxiliary components

The information in the table below applies to the horizontal mounting position of the device
at an ambient temperature of 50 °C.

Auxiliary com- Maximum permitted power Maximum total power

ponents consumption
+5 V +3.3 V +1.5 V
All components 6W3
Arduino shield Permitted power distribution:
Mini PCIe card -- 1.5 A 1 0.3 A 2 • Arduino shield: 4 W, Mini PCIe card: 0 W, USB:
USB 2.0 high 500 mA -- -- 2.5 W
current
• Arduino shield: 2 W, Mini PCIe card: 1 W, USB:
2.5 W
• Arduino shield: 0 W, Mini PCIe card: 2 W, USB:
2.5 W

1 May amount to maximum 3.0 A for up to 100 ms at start-stop torque of device

2 May amount to maximum 1.2 A for up to 100 ms at start-stop torque of device
3 With maximum total power, the permissible ambient temperature for the vertical mounting posi-
tion is reduced to 45 °C

Note
Device can overheat!
The power supply cannot make unlimited power available. The auxiliary components
consume energy and produce heat.
The device may overheat. The device and the auxiliary components may be damaged.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 41
Technical specifications
7.4 Technical data

7.4.4 Direct current supply (DC)

Technical specifications

Input voltage DC 9...36 V

Power consumption max. 10 W

Typical power consumption

Power consumption (at a rated voltage of 24 V)

Basic device 3.5 W
Arduino shields See section "Power demand of the components (Page 41)"
USB ports
Expansion cards

SIMATIC IOT2020, SIMATIC IOT2040

42 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.5 Hardware descriptions

7.5 Hardware descriptions

7.5.1 Motherboard
The following figures show the motherboard of the SIMATIC IOT2040. The interfaces X30,
X31 and X2 are not present in SIMATIC IOT2020.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 43
Technical specifications
7.5 Hardware descriptions

Component/interface Description / inscription Meaning, comment

H1 LEDs PWR Power (green)
H2 SD Micro SD card active (green)
H3 USB USB Power (5 V) is available (green)
H4 OC OverCurrent (red)
H5/H6 * USER User LED (green/red*/orange*), programma-
ble
S1 RESET For a reset of the CPU
S2 USER Status can be queried with programming
X1 Ethernet1
X2 Ethernet2 ready for PoE
X30, X31 COM D-Sub9
X60 USB A
X61 USB B Micro
X14 UART Debug
X40 Battery-Con
X50 µSD slot
X11, X13 Arduino, 8-pin (2x)
X10 Arduino, 10-pin
X12 Arduino, 6-pin
X15 ICSP Part of Arduino Interface
X16 JTAG Internal
X80 Power supply
X18 Jumper 3 pin SMD Jumper defines IO voltage for Arduino shield:
• Jumper on pins 1-2: 5 V
• Jumper on pins 2-3: 3.3 V
X100 MiniPCIe Con.
X101 Latch
X82 VIN Separation (power supply, Jumper defines VIN connection to the Ar-
9...36 V DC) duino shield:
• Jumper on pins 1-2: VIN is connected to
the Arduino shield
• Jumper on pins 2-3: VIN is not connected
to the Arduino shield

* The LED H6 is only available with SIMATIC IOT2040.

SIMATIC IOT2020, SIMATIC IOT2040

44 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.5 Hardware descriptions

7.5.2 External Interfaces

7.5.2.1 Power supply

Plug connector, 2-pin

Name of interface on the device: X80

Pin Assignment
1 GND (M)
2 +9...36 V DC (L+)

7.5.2.2 USB

USB socket type A

Name of interface on the device: X60

Pin Assignment
1 +5 VDC, out (max. 500 mA)
2 USB-DN
3 USB-DP
4 GND

USB socket Type Micro B

Name of interface on the device: X61

Pin Assignment
1 -
2 USB-DN
3 USB-DP
4 -
5 GND

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 45
Technical specifications
7.5 Hardware descriptions

7.5.2.3 Ethernet port

RJ45 socket
Name of interface on the device: X1 P1 LAN, X2 P1 LAN

Pin Short description Meaning

1 BI_DA+ Bidirectional data A+, input/output
2 BI_DA– Bidirectional data A–, input/output
3 BI_DB+ Bidirectional data B+, input/output
4 BI_DC+ Bidirectional data C+, input/output
5 BI_DC– Bidirectional data C–, input/output
6 BI_DB– Bidirectional data B–, input/output
7 BI_DD+ Bidirectional data D+, input/output
8 BI_DD– Bidirectional data D–, input/output

LED Short description Meaning

1 LED 1 Off: 10 Mbps
Lit green: 100 Mbps
2 LED 2 Off: Cable not connected
Lights up yellow: Connection established
Flashes: Data transfer active

7.5.2.4 Serial port (only SIMATIC IOT2040)

D-sub socket, 9-pin, with screw lock

Name of interface on the device: X30 COM, X31 COM

RS 232
RS 422
RS 485

Assignment RS 232

Pin Short description Meaning

1 DCD Data carrier detect (I)
2 RxD Received data (I)
3 TxD Transmitted data (O)
4 DTR Data terminal ready (O)

SIMATIC IOT2020, SIMATIC IOT2040

46 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.5 Hardware descriptions

Pin Short description Meaning

5 M Ground
6 DSR Data set ready (I)
7 RTS Request to send (O)
8 CTS Clear to send (I)
9 RI Incoming call (I)

Assignment RS 422

Pin Short description Meaning

1 TX- Transmitted data - (O) for full-duplex mode
2 TX+ Transmitted data + (O) for full-duplex mode
3 RX+ Receive data + (I) for full-duplex mode
4 RX- Receive data - (I) for full-duplex mode
5 M Signal ground
6 nc
7 nc
8 nc
9 nc

Assignment RS 485

Pin Short description Meaning

1 Data- Transmit / receive data - (I/O) for half-duplex mode
2 Data+ Transmit / receive data+ (I/O) for half-duplex mode
3 nc
4 nc
5 M Signal ground
6 nc
7 nc
8 nc
9 nc

7.5.3 Internal interfaces

7.5.3.1 Arduino shield interfaces

The tables below show the pin assignment of the interfaces of the Arduino shield, depending
on the operating mode.
The position of the interfaces and Pin 1 of the respective interface is available in section
"Motherboard (Page 43)".

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 47
Technical specifications
7.5 Hardware descriptions

X10

Pin Operating mode

DIGITAL ANALOG POWER SERIAL SPI I2C PWM
1 8
2 9 X
3 10 SS X
4 11 MOSI X
5 12 MISO
6 13 SCK
7 GND
8
9 18 A4 SDA
10 19 A5 SCL

X11

Pin Operating mode

DIGITAL ANALOG POWER SERIAL SPI I2C PWM
1 0 RxD
2 1 TxD
3 2
4 3 X
5 4
6 5 X
7 6 X
8 7

X12

Pin Operating mode

DIGITAL ANALOG POWER SERIAL SPI I2C PWM
1 14 A0
2 15 A1
3 16 A2
4 17 A3
5 18 A4 SDA
6 19 A5 SCL

X13

Pin Operating mode

DIGITAL ANALOG POWER SERIAL SPI I2C PWM
1
2 IOREF
3 RESET

SIMATIC IOT2020, SIMATIC IOT2040

48 Operating Instructions, 07/2022, A5E37656492-AC
 Technical specifications
7.5 Hardware descriptions

Pin Operating mode

4 3,3 V
5 5V
6 GND
7 GND
8 VIN

X15 (ICSP)

Pin Operating mode

DIGITAL ANALOG POWER SERIAL SPI I2C PWM
1 12 MISO
2 5V
3 13 SCK
4 11
5 RESET MOSI
6 GND

7.5.3.2 UART Debug

X14

Pin Assignment
1 GND
2 RTS_N
3 n. c.
4 RxD
5 TxD
6 CTS_N

7.5.3.3 Mini PCIe interface

Pin Signal Name Pin Signal Name

51 W_DISABLE2# 52 +3.3 Vaux
49 Reserved 50 GND
47 Reserved 48 +1.5 V
45 Reserved 46 LED_WPAN#
43 GND 44 LED_WLAN#
41 +3.3Vaux 42 LED_WWAN#
39 +3.3Vaux 40 GND
37 GND 38 USB_D+
35 GND 36 USB_D-
33 PETp0 34 GND
31 PETn0 32 SMB_DATA

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 49
Technical specifications
7.5 Hardware descriptions

Pin Signal Name Pin Signal Name

29 GND 30 SMB_CLK
27 GND 28 +1.5V
25 PERp0 26 GND
23 PERn0 24 +3.3Vaux
21 GND 22 PERST#
19 Reserved (UIM_C4) 20 W_DISABLE1#
17 Reserved (UIM_C8) 18 GND
Nose
15 GND 16 UIM_VPP
13 REFCLK+ 14 UIM_RESET
11 REFCLK- 12 UIM_CLK
9 GND 10 UIM_DATA
7 CLKREQ# 8 UIM_PWR
5 COEX2 6 1.5 V
3 COEX1 4 GND
1 WAKE# 2 3.3 Vaux

7.5.3.4 Micro SD interface

Pin Abbreviation Function

1 Dat2 Data line bit 2
2 Dat3 Card Detect / data line bit 3
3 CMD Command Line
4 Vdd Voltage supply 2.7–3.6 V
5 Clk Clock input
6 GND Signal Ground
7 Dat0 Data line bit 0
8 Dat1 Data line bit 1

SIMATIC IOT2020, SIMATIC IOT2040

50 Operating Instructions, 07/2022, A5E37656492-AC
Technical support 8
You can find additional information and support for the products described on the Internet at
the following addresses:
• Technical support
(https://support.industry.siemens.com/cs/start?lc=en-WW)
• Support request form
(https://support.industry.siemens.com/My/ww/en/requests)
• After Sales Information System SIMATIC IPC/PG
(http://www.siemens.com/asis)
• SIMATIC Documentation Collection
(http://www.siemens.com/simatic-tech-doku-portal)
• Your local representative
(http://w3.siemens.com/aspa_app/)
• Training center
(http://sitrain.automation.siemens.com/sitrainworld/?AppLang=en)
• Industry Mall
(https://mall.industry.siemens.com)
When contacting your local representative or Technical Support, please have the following
information at hand:
• MLFB of the device
• BIOS version for industrial PC or image version of the device
• Other installed hardware
• Other installed software

Tools & downloads

Please check regularly if updates and hotfixes are available for download to your device. The
download area is available on the Internet at the following link:
After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis)

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 51
List of abbreviations A
ACPI Advanced Configuration and
Power Interface
BIOS Basic Input Output System
CE Communauté Européenne
COM Communications Port Term for the serial interface
CPU Central Processing Unit CPU
CSA Canadian Standards Association Canadian organization for tests and certifications
according to national or binational standards
CTS Clear To Send Clear to send
DC Direct Current DC current
DCD Data Carrier Detect Data carrier signal detection
DQS Deutsche Gesellschaft zur Zer-
tifizierung von Qualitätsman-
agement mBH
DSR Data Set Ready Ready for operation
DTR Data Terminal Ready Data terminal is ready
ESD Components sensitive to electro-
static charge
EN European standard
ESD Electrostatic Sensitive Device Electrostatic Sensitive Devices
Electrostatic discharge Electrostatic discharge
GND Ground Chassis ground
IDE Integrated Device Electronics
IEC International Electronical Com-
mission
LAN Local Area Network Computer network that is limited to a local area.
LED Light Emitting Diode Light emitting diode
LPS Limited Power Source
MAC Media access control Media access control
MLFB Machine-readable product desig-
nation
PC Personal computer
PCIe Peripheral Component Intercon- High-speed serial, differential full-duplex PtP
nect express interface with high data rate.
PG Programming device
RI Ring Input Incoming call
RTS Request to send Request to send
RxD Receive Data Data transfer signal
SELV Safety Extra Low Voltage Safety extra low voltage
UEFI Unified Extensible Firmware In-
terface

SIMATIC IOT2020, SIMATIC IOT2040

52 Operating Instructions, 07/2022, A5E37656492-AC
 List of abbreviations

UL Underwriters Laboratories Inc. US organization for testing and certification ac-

cording to national or binational standards.
USB Universal Serial Bus

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 53
Glossary

CE marking
Communauté Européene: The CE symbol confirms the conformity of the product with all
applicable EC directives such as the EMC Directive.

COM interface
The COM interface is a serial V.24 interface. The interface is suitable for asynchronous data
transfer.

Distribution framework
Exemplary reference distribution "Poky" of Embedded Linux (see "Yocto" and "Poky").

Drivers
Program parts of the operating system. They adapt user program data to the specific formats
required by I/O devices such as hard disk, printers, and monitors.

Embedded Linux
Linux for industrial, embedded systems (see "Yocto" and "Poky").

ESD Guideline
Guideline for using electrostatic sensitive components.

Ethernet
Local network (bus structure) for text and data communication with a transfer rate of 10/100
Mbps.

Interface
• Physical interconnection (cable) of hardware elements such as PLCs, PCs, programming
devices, printers or monitors.
• Interface for interactive software applications.

LAN
Local Area Network: LAN is a local network that consists of a group of computers and other
devices that are distributed across a relatively restricted range and are linked with

SIMATIC IOT2020, SIMATIC IOT2040

54 Operating Instructions, 07/2022, A5E37656492-AC
 Glossary

communication cables. The devices connected to a LAN are called nodes. The purpose of
networks is the mutual use of files, printers or other resources.

Module
Modules are plug-in units for PLCs, programming devices or PCs. They are available as local
modules, expansion modules, interfaces or mass storage (Mass storage module).

Motherboard
The motherboard is the core of the computer. Here, data are processed and stored, and
interfaces and device I/Os are controlled and managed.

Operating system
Generic term which describes all functions for controlling and monitoring user program
execution, distribution of system resources to the user programs and the operating mode in
cooperation with the hardware (for example, Windows 7 Ultimate).

Poky
Cross-hardware framework of the "Yocto" project for creation of customized Embedded
Linuxdistributions for industrial, embedded systems. The reference distribution "Poky"
contains the OpenEmbedded build system "BitBake" and the OpenEmbedded kernel as well as
a set of metadata.

Reset
Hardware reset: Reset/restart of the PC using a button/switch.

Yocto
Open Source collaboration under the guidance of the Linux Foundation for standardization of
the Embedded Linux development. Yocto banks on the OpenEmbedded build system and
propagates the "Poky" reference distribution.

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 55
Index

A F
Arduino shield FCC, 33
Installing, 25 Features, 7
Australia, 33 Flash, 39

B G
Backup battery General technical specifications, 38
Installing, 31

I
C Identification data, 17
CE marking, 32 Installation on a DIN rail, 17
Certificates, 32 Installing
Approvals, 33 Arduino shield, 25
Clearance, 18 Backup battery, 31
Components sensitive to electrostatic charge, 35 Mini PCIe card, 27
Condensation, 16 Interfaces, 39
Configuration SIMATIC IOT2020, 8
SIMATIC IOT2020, 8
SIMATIC IOT2040, 9
Connecting L
Peripherals, 22
Labeling, 34
Power supply, 23
Korea, 34
Current consumption, 38
Limitation of liability, 13, 29

D M
DC power supply, 42
Marking
Degree of protection, 38
EU Declaration of Conformity, 32
Dimension drawings, 37
Micro SD card, 25
Directive
Mini PCIe card
ESD Directive, 35
Installing, 27
Motherboard
Technical features, 44
E
Mounting
EAC, 34 Wall, 21
ESD, 35 Mounting position, 17
ESD Directive, 35 Mounting type, 17
EU Declaration of Conformity, 32
Expansion slot, 39
N
New Zealand, 33

SIMATIC IOT2020, SIMATIC IOT2040

56 Operating Instructions, 07/2022, A5E37656492-AC
 Index

Noise emission, 38

P
Package contents, 15
Checking, 15
Packaging, 15
Checking, 15
Removing, 15
Ports
SIMATIC IOT2040, 9
Power supply
Connecting, 23
DC power supply, 42
Processor, 39
PROFINET, 42
Protective measure
Static electricity, 36

R
Radiation, 14
High frequency radiation, 14
RAM, 39
Rating plate, 17
Repairs, 29

S
Safety instruction
Storage, 16
Transportation, 16
Static electricity
Protective measures, 36
Supply voltage, 38

U
UKCA, 32
USB Flash Drive, 10

W
Wall mounting, 17, 21
Warranty, 12
Weight, 38

SIMATIC IOT2020, SIMATIC IOT2040

Operating Instructions, 07/2022, A5E37656492-AC 57