Click below buttons to visit particular Department

EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 1

Dharmapuri – 636 703

LAB MANUAL

Regulation : 2013
Branch : B.E. – ECE
Year & Semester : II Year / IV Semester

EC6412- LINEAR INTEGRATED CIRCUIT LABORATORY

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 2

ANNA UNIVERSITY: CHENNAI

REGULATION 2013
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY

LIST OF EXPERIMENTS:

DESIGN AND TESTING OF

1. Inverting, Non inverting and Differential amplifiers.

2. Integrator and Differentiator.
3. Instrumentation amplifier
4. Active low-pass, High-pass and band-pass filters.
5. Astable &Monostable multivibrators and Schmitt Trigger using op-amp.
6. Phase shift and Wein bridge oscillators using op-amp.
7. Astable and monostable multivibrators using NE555 Timer.
8. PLL characteristics and its use as Frequency Multiplier.
9. DC power supply using LM317 and LM723.
10.Study of SMPS.

SIMULATION USING SPICE

1. Simulation of Experiments 3, 4, 5, 6 and 7.

2. D/A and A/D converters (Successive approximation)
3. Analog multiplier
4. CMOS Inverter, NAND and NOR

TOTAL-45 PERIODS

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 3

INDEX
SIGNATURE
Ex.No. DATE LIST OF THE EXPERIMENT OF THE REMARKS
STAFF

INVERTING & NON-INVERTING

1
AMPLIFIERS USING OP-AMP

2 DIFFERENTIAL AMPLIFIERS USING

OP-AMP

3 INTEGRATOR AND DIFFERENTIATOR USING

OP-AMP.

4
INSTRUMENTATION AMPLIFIER

5 ASTABLE, MONOSTABLE MULTIVIBRATOR

USING OP-AMP.

6
SCHMITT TRIGGER USING OP-AMP

RCPHASE SHIFT AND WEIN BRIDGE

7 OSCILLATOR USINGOPAMP

8 ACTIVE LOWPASS, HIGH PASS AND BAND

PASS FILTER USINGOP-AMP.
P

9 ASTABLE AND MONOSTABLE

MULTIVIBRATOR USING IC555 TIMER

10 PLL CHARACTERISTICS
AND FREQUENCY MULTIPLIER USING PLL

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 4

SIGNATURE
Ex.No. DATE LIST OF THE EXPERIMENT OF THE REMARKS
STAFF

11 DCPOWER SUPPLY USING LM317

12
DCPOWER SUPPLY USING LM 723

13
STUDY OF SMPS

SIMULATION OF INSTRUMENTATION
14
AMPLIFIER USING PSPICE

SIMULATION OF ACTIVE LOWPASS, HIGH PASS

15 AND BAND PASS FILTER USING PSPICE

SIMULATION OF ASTABLE, MONOSTABLE

16 MULTIVIBRATOR & SCHMITT TRIGGER USING
PSPICE

SIMULATION OF RC PHASE SHIFT AND

17 WEIN BRIDGE OSCILLATOR USING
PSPICE

SIMULATION OF ASTABLE AND

18 MONOSTABLE MULTI VIBRATOR USING
IC555 TIMER

SIMULATION OF ADC,DAC AND ANALOG

19
MULTIPLIER USING PSPICE

SIMULATION OF CMOS INVERTER,NAND

20
AND NOR USING PSPICE

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 5

INTRODUCTION OF LINEAR CIRCUIT

A linear circuit is an electronic circuit in which, for a sinusoidal input voltage

of frequency f, any steady-state output of the circuit (the current through any
component, or the voltage between any two points) is also sinusoidal with
frequency f. Note that the output need not be in phase with the input.

An equivalent definition of a linear circuit is that it obeys the superposition

principle. This means that the output of the circuit F(x) when a linear combination
of signals ax1(t) + bx2(t) is applied to it is equal to the linear combination of the
outputs due to the signals x1(t) and x2(t) applied separately:

It is called a linear circuit because the output of such a circuit is a linear

function of its inputs. Informally, a linear circuit is one in which the electronic
components' values (such as resistance, capacitance, inductance, gain, etc.) do not
change with the level of voltage or current in the circuit. Linear circuits are
important because they can amplify and process electronic signals without
distortion. An example of an electronic device that uses linear circuits is a sound
system.

Linear circuits are important because they can process analog signals without
introducing inter modulation distortion. This means that separate frequencies in the
signal stay separate and do not mix, creating new frequencies (heterodynes).

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 6

STUDY OF OP-AMP

An operational amplifier or op-amp is a linear integrated circuit that has a

very high voltage gain, high input impedance and low output impedance. Op-
amp is basically a differential amplifier whose basic function is to amplify the
difference between two input signals.
Op-amp has five basic terminals, that is, two input terminals, one o/p
terminal and two power supply terminals. Pin2 is called the inverting input
terminal and it gives opposite polarity at the output if a signal is applied to it. It
produces a phase shift of 180o between input and output. Pin3 is called the non-
inverting terminal that amplifies the input signal without inversion, i.e., there is
no phase shift or i/p is in phase with o/p. The op-amp usually amplifies the
difference between the voltages applied to its two input terminals. Two further
terminals pins 7 and 4 are provided for the connection of positive and negative
power supply voltages respectively. Terminals 1 and 5 are used for dc offset.
The pin 8 marked NC indicates ‘No Connection’.
Study of op-amp

Offset Null 1 8 N/C

Inverting i/p V+
2 7
IC 741
Non Inverting 3 6 O/p
i/p

V- 4 5 Offset Null

Block schematic of op-amp

-
V2 Diff Diff Buffer & level O/p
amp V0
V1
+
amp translator driver

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 7

CIRCUIT DIAGRAM- (INVERTING AMPLIFIER):

Rf

+15 V
10K
7
+15 V
Ri
2 7
6
IC 741
10K
-15 V
4
3
CRO
-15 V
Vin

DESIGN PROCEDURE:

 VO = -I Rf _____________

 I =Vin /Ri _____________

 VO = - (Vi / R i)Rf _____________

 Gain AV =VO / Vi = -( Rf / Ri) ____________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 8

Ex. No : 01
DESIGN AND TESTING OF INVERTING AND NON INVERTING
DATE : AMPLIFIERS

AIM:

To design and test inverting and non inverting amplifiers using

IC µA 741

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

1 Dual power supply (0 - +15)V 1
2 Signal generator (0-3)MHz 1
3 CRO (0-30)MHz 1
4 IC µA 741 1
5 Resistor 10KΩ,5KΩ 2,1

THEORY:

INVERTING AMPLIFIER:

The fundamental component of any analog computer is the operational

amplifier or op-amp and the frequency configuration in which it is used as an
inverting amplifier. An input voltage Vin is applied to the input voltage. It
receives and inverts its polarity producing an output voltage (VO). This same
output voltage is also applied to a feedback resistor Rf, which is connected to
the amplifier input analog with Ri. The amplifier itself has a very high voltage
gain. If Rf=Ri then Vo=Vi

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 9

TABULATION –(INVERTING AMPLIFIER):

INPUT SIGNAL OUTPUT SIGNAL

S.NO.
AMPLITUDE TIME AMPLITUDE TIME
(Vi) (T) (Vo) (T)
volts ms volts ms

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 10

CIRCUIT DIAGRAM –(NON INVERTING AMPLIFIER):

10k

10k

DESIGN PROCEDURE:

 Gain Av = Vo/Vi _______________________

= (Rf+Ri) / Ri _______________________

=1+ (Rf / Ri) ______________________

 Vin = Vo.Ri / (Ri+Rf) _______________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 11

NON- INVERTING AMPLIFIER:

Although the standard op-amp configuration is as an inverting amplifier,

there are some applications where such inversion is not wanted. However, we
cannot just switch the inverting and non inverting inputs to the amplifier itself.
We will still need negative feedback to control the working gain of the circuit
.Therefore, we will need to leave the resistor structure around the op-amp intact
and swap the input and ground connections to the overall circuit.
VO/VI = ( Rf/ Ri )+1
From the calculations, we can see that the effective voltage gain of the non-
inverting amplifier is set by the resistance ratio. Thus, if the two resistors are
equal value, then the gain will be 2 rather than 1.

EXPERIMENTAL PROCEDURE:
1. Connect the circuit as shown in the diagram.
2. Give the input signal as specified.
3. Switch on the dual power supply
4. Note the outputs from the CRO.
5. Draw the necessary waveforms on the graph sheet.
6. Repeat the above procedure for non-inverting amplifier circuit.
7. Compare the practical gain with theoretically designed gain.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 12

TABULATION –(NON- INVERTING AMPLIFIER ):

INPUT SIGNAL OUTPUT SIGNAL

S.NO. AMPLITUDE TIME AMPLITUDE TIME
(Vi) (T) (Vo) (T)
volts ms volts ms

MODEL GRAPH

RESULT :
Thus the inverting and non inverting amplifier circuits using operational
amplifier Ic µA 741 are designed, constructed and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 13

CIRCUIT DIAGRAM - (DIFFERENTIAL AMPLIFIER)

Rf
10k
k

+15 V
Ri
10k 2 7
V1 k
ICµA74
6
1
V2
4
10k Ri 3
CRO
-15 V

Rc
10k

DESIGN PROCEDURE:

 V1 =V2 =V _____________________

 VC = (V1+ V2)/2 =V _____________________

 AC = V0/VC _____________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 14

Ex. No : 02
DESIGN OF DIFFERENTIAL AMPLIFIER
DATE :

AIM:

To design and test a differential amplifier using operational amplifier

IC µA 741

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

1 Dual power supply (0 - +15)V 1
2 Signal generator (0-3)MHz 2
3 CRO (0-30)MHz 1
4 IC µA 741 1
5 Resistor 10KΩ 4

THEORY:

A circuit that amplifies the difference between two signals is called as a

differential amplifier. This type of amplifiers is very useful in instrumentation
circuits.

From the experimental setup of a differential amplifier, the voltage at the

output of the operational amplifier is zero. The inverting and non-inverting
terminals are at the same potential. Such a circuit is very useful in detecting
very small differences in signals. Since the gain can be chosen to be very large.
For example, if R2=100Ri, then a small difference V1-V2 is amplified 100 times.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 15

TABULATION –( DIFFERENTIAL AMPLIFIER):

V1 V2 OUTPUT Vo GAIN
S.
NO.
volts volts Vi = Vd =V1-V2
volts volts THEORETICAL PRACTICAL

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 16

EXPERIMENTAL PROCEDURE:

1 Connections are made as per the EXPERIMENTAL SETUP.

2 The supply is switched ON.
3 Output is connected to anyone channel of CRO.
4 The V1 and V2 voltages are fixed and measured from the other channel
of CRO and the corresponding output voltages are also noted from the
CRO.
5 The above step is repeated for various values of V1 and V2.V1 and V2
may be AC or DC voltages from function generator or DC power
supply.
6 Readings are tabulated and gain was calculated and composed with
designed values.

RESULT:

Thus the differential amplifier is tested using operational amplifier

IC µA 741.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 17

CIRCUIT DIAGRAM_- (INTEGRATOR);

10µf

10k

10k

2k

DESIGN PROCEDURE:

 V= -1/ (Rf.Cf) [Vin(t).Vo(t)] _______________________

 T = -1/ (Rf.Cf) _____________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 18

Ex. No : 03
INTEGRATOR AND DIFFERENTIATOR

DATE :

AIM:

To design and test the integrator and differentiator using operational

amplifier IC µA 741

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 Signal generator (0-3)MHz 1
3 CRO (0-30)MHz 1
4 IC µA 741 1
5 Resistor 10KΩ,5KΩ 2,1
6 Capacitor 10µf 1

THEORY:

INTEGRATOR:

Op-amps allow us to make nearly perfect integrators such as the practical integrator
The circuit incorporates a large resistor in parallel with the feedback capacitor. This is
necessary because real op-amps have a small current flowing at their input terminals called
the "bias current". This current is typically a few nano amps, and is neglected in many
circuits where the currents of interest are in the micro amp to milliamp range. The feedback
resistor gives a path for the bias current to flow. The effect of the resistor on the response is
negligible at all but the lowest frequencies.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 19

TABULATION-( INTEGRATOR):

INPUT WAVEFORM OUTPUT WAVEFORM

AMP. TIME F=1/T AMP. TIME F=1/T

(V) (T) (V) (T)
volts ms KHz volts ms KHz

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 20

CIRCUIT DIAGRAM- (DIFFERENTIATOR):

10k

1k 10µf

DESIGN PROCEDURE:

 fmax = 1 / (2πC1Rf) _______________________

 Vout = -1/Rf.Cf [DVin/ dt] ______________________

 T = - Rf.Cf _______________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 21

DIFFERENTIATOR:

One of the simplest of the operational amplifier that contains capacitor is

differential amplifier. As the suggests, the circuit performs the mathematical
operation of differentiation. The output is the derivative of the given input
signal voltage. The minus sign indicates an 1800 phase shift of the output
waveform Vo with respect to the input signal.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 22

TABULATION –(DIFFERENTIATOR) :

INPUT WAVEFORM OUTPUT WAVEFORM

AMP. TIME F=1/T TIME F=1/T

AMP.
(V) (T) (T)
(V)
volts ms KHz ms KHz
volts

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 23

EXPERIMENTAL PROCEDURE:

1 The connections are given as per the EXPERIMENTAL SETUP.

2 The supply is switched ON after checking the circuit connections
3 The input wave form is applied from the function generator and the
corresponding output waveform is noted from the CRO.
4 The above mentioned procedure is repeated for differentiator also.

RESULT :

Thus the integrator and differentiator is designed and tested using

operational amplifier IC µA 741

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 24

CIRCUIT DIAGRAM-( INSTRUMENTATION AMPLIFIER):

DESIGN PROCEDURE:

 V01 = (1+R2/R1)V1- (R2/R1)V2,

 V02 = (1+R2/R1)V2 - (R2/R1)V1

 V0 =V02 - V01 _________________________________

= (V2-V1) (1+2R2/R1) ____________________

Let R1=R2=R3=R4= ___________________________

 Gain = V0/Vi

 = Vo/(V2-V1)

 Gain = _______________________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 25

Ex. No :04
INSTRUMENTATION AMPLIFIER
DATE :

AIM:

To design and test instrumentation amplifier using ICµA 741 for the

given gain.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 Signal generator (0-3)MHz 1
3 CRO (0-30)MHz 1
4 IC µA 741 1
5 Resistor 10kΩ 6

THEORY:

In a number of instrumentation and consumer applications one is required

to measure and control the physical quantities. Some typical examples are
measurement and control of temperature , humidity, light,
Intensity , water flow etc.
These physical quantities are usually measured with the help of
transducer. The output of the transducer has to be amplified so that it can derive
the indicator or display system. The function performed by an instrumentation
amplifier are,

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 26

TABULATION –( INSTRUMENTATION AMPLIFIER):

INPUT SIGNAL OUTPUT SIGNAL

S.NO
AMPLITUDE TIME AMPLITUDE TIME
(Vi) (T) (Vo) (T)
volts ms volts ms

MODEL GRAPH:

AMP(V)
INPUT WAVEFORM

TIME(ms)

AMP(V)

OUTPUT WAVEFORM

TIME(ms)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 27

 High CMRR
 High gain stability with low temperature coefficient
 Low dc offset
 Low input impedance

These are specially designed op-amp such as VA725 to meet the above
started requirement of a good instrumentation amplifier. Monolithic
instrumentation amplifiers are also available commercially such as AD521,
AD524, AD624 by analog devices L40036, and L40037 by national
semiconductors.
EXPERIMENTAL PROCEDURE:

1 Circuit connections are given as per the EXPERIMENTAL SETUP.

2 The input signal is given
3 The dual power supply is switched ON.
4 The input is varied in steps and the corresponding output readings are
noted from CRO.
5 The practical gain is calculated from the readings and compared with the
theoretically designed gain.

RESULT :
Thus the instrumentation amplifier is designed and tested using ICµA741.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 28

CIRCUIT DIAGRAM-( ASTABLE MULTIVIBRATOR);

5kΩ

105k
0.1µf ΩΩ
ff

8.6k

DESIGN PROCEDURE:

 f0 = 1/ (2RC) Let f0= _____________________

 R1 = _____R2 Assume , C= ____________________

R2 = ______ R=____________________

R1 = _____

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 29

Ex. No :05
ASTABLE AND MONOSTABLE MULTIVIBRATOR

DATE :

AIM:

To design and test an astable and monostable multivibrator circuits using

op-amp IC µA 741

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 CRO (0-30)MHz 1
3 IC µA 741 1
4 Resistor 15kΩ,10kΩ 2,2
6 Capacitor 0.1µf 2

THEORY:

ASTABLE MULTIVIBRATOR:

The astable multivibrator is also known as free running oscillator. the principle
of generation of square wave output is to force an op-amp to operate in
saturation region. β = R2/(R1+R2) of the output is feedback to the positive input
terminal. the reference voltage is Vo and may take the values as +βVsat and –
βVsat. The output is also feedback to the negative input terminal after
interchanging by a low pass RC combination. Whenever input terminal just
exceeds Vref switching takes place resulting in square wave output. In this
multivibrator both sates are quasi stable state

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 30

TABULATION-( ASTABLE MULTIVIBRATOR) :

AMPLITUDE TIME FREQUENCY

S.NO. WAVEFORM (V) (T) F=1/T
volts ms Hz
CAPACITOR
1

OUTPUT
2

MODEL GRAPH:

Vo(V)

Vsat

+βVsat
TIME (ms)

–βVsat

–Vsat

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 31

CIRCUIT DIAGRAM- (MONOSTABLE MULTIVIBRATOR)_

15k

0..1µ

15k

0.1µ

15k
15k

DESIGN PROCEDURE:

 T= RC ln 1+VD/VSAT , where β = R2/(R!+R2)

1-β

If, VSAT > VD & R1=R2 , β= 0.5 then ,

T= _______________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 32

MONOSTABLE MULTIVIBRATOR:

The monostable multivibrator is also called as one shot multivibrator. The

circuit produces a single pulse of specified duration in response to each external
trigger response. It is always have one stable state. When an external trigger is
applied, the output changes the state. The new state is called quasi stable state.
The circuit remain in this state for a fixed interval of time and then it returns to
the original state after this interval. this time interval is determined by the
charging and discharging of the capacitor.

EXPERIMENTAL PROCEDURE:

ASTABLE MULTIVIBRATOR:

1 Connections are given as per the EXPERIMENTAL SETUP.

2 Supply is switched ON after checking the circuit connections.
3 The output square wave form and the capacitor charging and
discharging waveforms are noted from the CRO.

MONOSTABLE MULTIVIBRATOR:

1 Connections are given as per the EXPERIMENTAL SETUP.

2 Supply is switched ON after checking the circuit connections.
3 The output square wave form and the capacitor charging and discharging
waveforms are note down from the CRO.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 33

TABULATION -( MONOSTABLE MULTIVIBRATOR):

AMPLITUDE TIME FREQUENCY

S.NO. WAVEFORM (V) (T) F=1/T
volts ms Hz

INPUT
1 (TRIGGER)

OUTPUT
2

MODEL GRAPH:

RESULT :
Thus the astable and monostable multivibrator circuits were designed
and tested using ICµA741.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 34

CIRCUIT DIAGRAM-( SCHMITT TRIGGER):

10k

6.8k
200k

DESIGN PROCEDURE:

± Vsat = _____________________

 Vutp = R2(+Vsat / (R1+R2)) ____________________

 Vltp = R2(-Vsat / (R1+R2)) ______________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 35

Ex. No :06

SCHMITT TRIGGER
DATE :

AIM:
To design and test a Schmitt Trigger circuit using IC µA 741.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 CRO (0-30)MHz 1
3 IC µA 741 1
4 Resistor 6.8kΩ,200kΩ,10kΩ 2,2,1

THEORY:

If the positive feedback is added to the comparator circuit means gain can
be increased greatly. Consequently the transfer curve comparator becomes more
close to the ideal curve theoretically. If the loop gain βfo is adjusted to unity
then the gain with feedback average becomes extreme values of output voltage.
in practical circuits, however it may not be possible to maintain loop gain
exactly equal to unity for a long time because of supply voltage and temperature
variations so a value greater than unity is chosen. This gives the output
waveform virtually disconnected at the comparison voltage. This circuit
however exhibits phenomenon called hystersis or backlash.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 36

TABULATION –( SCHMITT TRIGGER) :

VOLTAGE TIME
S.NO. SIGNAL (V) (T)
volts ms

INPUT
SIGNAL

OUTPUT
SIGNAL

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 37

EXPERIMENTAL PROCEDURE:

1 Connections are given as per the EXPERIMENTAL SETUP.

2 The supply is switched ON.
3 The output waveform was noted from CRO and UTP and LTP are
noted. The graph is drawn.
4 The theoretical value of UTP and LTP are verified with the practical
value.

RESULT :
Thus the Schmitt Trigger circuit using IC µA 741 was designed and
tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 38

CIRCUIT DIAGRAM – (RC PHASE SHIFT OSCILLATOR);

Rf

680k

+15 V
R1
2 7
6
ICµA
2k 741
4 CRO
3
Rc -15 V
68k
k

C C C
0.1µ 0.1µ 0.1µ

10k R 10k R 10k R

k

DESIGN PROCEDURE:
Design for RC
 f = 1/(2π√6 RC),
Assume C = ____________
R= _____________
Design for Gain

 Av= - Rf/R1, Let R1 = ______________

Rf = ______________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 39

Ex. No :07
RC PHASE SHIFT OSCILLATOR AND WEIN BRIDGE OSCILLATOR

DATE :

AIM:

To design and test RC phase shift and wein bridge oscillators using IC
µA 741.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 Signal generator (0-3)MHz 1
3 CRO (0-30)MHz 1
4 IC IC µA 741 1
680kΩ,6.8kΩ,220kΩ,
5 Resistor 3,2,2,1
4.7kΩ
6 Capacitor 0.1µf 3

THEORY:

RC PHASE SHIFT OSCILLATOR:

RC phase shift oscillator using op-amp, in inverting amplifier mode. Thus

it introduces a phase shift of 1800 between the input and output. The feedback
network consists of 3 RC sections producing each 600 phase shift. Such a circuit
is known as RC phase shift network. The circuit is generating its own output
signal and a stage of oscillator sustained. the phase shift produced by op-amp is
1800.the op-amp with a gain of 29 and RC network is of equal resistor and
capacitor connected feedback the op-amp output and input terminals..

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 40

TABULATION-( RC PHASE SHIFT OSCILLATOR):

AMPLITUDE TIME F = 1/T

S.NO. (V) (T)

volts ms Hz

MODEL GRAPH:

AMP(V)
RC PHASE SHIFT OSCILLATOR

TIME(ms)

AMP(V)

WIEN BRIDGE OSCILLATOR

TIME(ms)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 41

CIRCUIT DIAGRAM-(WIEN BRIDGE OSCILLATOR):

5.3k

5.3k

20k 0.01µ

10k 0.01µ

DESIGN PROCEDURE:
Design for RC,

f = 1/(2πRC) ,
Assume C = __________
R = ___________

Design for Gain,

 R1 = _____ , Rf = __________

 Gain A= 1+Rf/R1

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 42

WEIN BRIDGE OSCILLATOR:

It is commonly used in audio frequency oscillator. The feedback signal is

connected in the input terminal so that the output amplifier is working as an
non-inverting amplifier. The wein bridge circuit is connected between amplifier
input terminal and output terminal. The bridge has a series R network, in one
arm and a parallel RC network in the adjoining arm. in the remaining two arms
of the bridge, resistor R1 and Rf are connected. the phase angle criterion for
oscillation is that the total phase shift around the circuit must be zero. This
condition occurs when bridge is balanced. At resonance frequency of oscillation
fo is exactly the resonance frequency of balanced wein bridge and is given by f0
= 1/ (2πfC).assuming that the resistors are input impedance value and
capacitance are equal to the value in the reactive stage of wein bridge. at this
frequency, the gain required for sustained.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 43

TABULATION –(WEIN BRIDGE OSCILLATOR) :

AMPLITUDE TIME F = 1/T

S.NO. (V) (T)

volts ms Hz

MODEL GRAPH:

AMP(V)
RC PHASE SHIFT OSCILLATOR

TIME(ms)

AMP(V)

WIEN BRIDGE OSCILLATOR

TIME(ms)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 44

EXPERIMENTAL PROCEDURE:
RC PHASE SHIFT OSCILLATOR:

1 Circuit connections are given as per the EXPERIMENTAL SETUP.

2 Supply is switched ON.
3 3600 phase shift output is obtained at the output.
4 The inverting op-amp produce 1800 and RC network produce another
1800
5 Frequency is calculated by the formula f =1/T

WIEN BRIDGE OSCILLATOR:

1 Connections are given as per the EXPERIMENTAL SETUP.

2 Resistor and capacitor values are verified simultaneously; the
corresponding Rf value is noted.
3 The critical vale of frequency is noted correspondingly.
4 Check whether the calculated and observed frequency values are
same.
5 Graph is drawn by taking amplitude along y-axis and time along x-
axis.the graph will b sine waveform.

RESULT:
Thus the RC phase shift and wien bridge oscillator was designed and
tested using IC µA 741.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 45

CIRCUIT DIAGRAM-( ACTIVE LOW PASS FILTER):

27k

47k

47k 47k

DESIGN PROCEDURE:

 fc = 1/2πRC,
Let C =

Therefore R =

Design for Gain:

 A = 1+Rf/R1, Therefore,
Rf = ___________

R1= ___________

Let A = _________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 46

Ex. No :08
ACTIVE LOW PASS, HIGH PASS AND BAND PASS FILTER
DATE :

AIM:
To design and test low pass, high pass and band pass filters using IC
µA 741.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 CRO (0-30)MHz 1
3 IC µA 741 1
4 Resistor 10kΩ,5kΩ, 4,2
6 Capacitor 0.1µf,10µf 2,1

THEORY:

The first order low pass filter is realized RC circuit used along with
an op-amp in non-inverting configuration. A low pass filter has constant gain
from) Hz to fH.. Bandwidth of this filter is fH. Bandwidh of electric filters are
used in circuits which require the separation of signals according to their
frequencies. a first order low pass filter consists of a single RC network
connected to the positive input terminal of non-inverting op-amp amplifier.
Resistors Ri and Rf determine the gain of the filter in the pass band.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 47

TABULATION-( ACTIVE LOW PASS FILTER) :

Vin =
INPUT OUTPUT
FREQUENCY VOLTAGE GAIN =
S.NO (Fi) (Vo) 20LOG(Vo/Vin)
Hz mV

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 48

CIRCUIT DIAGRAM-( ACTIVE HIGH PASS FILTER):

5k

68k

0.1µ
11
0.1µ
56k
56k
k

DESIGN PROCEDURE:
 fc = 1/2πRC, Let C = ___________

Therefore R = ___________

Design for Gain:

R1 = ___________

 A = 1+Rf/R1, Rf= ____________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 49

TABULATION –( ACTIVE HIGH PASS FILTER):

Vin =
INPUT OUTPUT
FREQUENCY VOLTAGE GAIN =
S.NO. (Fi) (Vo ) 20LOG(Vo/Vin)
Hz mV

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 50

CIRCUIT DIAGRAM –( ACTIVE BAND PASS FILTER):

Rf

Ri 10kΩ Rf 5k
Ri 5k
k k
10kΩ
R1
2 -
0.01 µF 2 -
3 +
3 + 741 Vout
741 C1
~ C2 R2
0.01 µF
Vin 10k

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 51

DESIGN PROCEDURE:

The parameters in the band pass filter are lower cutoff frequency, the
upper cutoff frequency and the bandwidth, the central frequency gain Ao and
selectivity Q. The higher the selectivity Q, the sharper the filter. Below 0.5fo all
filters roll off at -20dB/decade independent of the value of Q. This is limited by
the two RC pair of circuits.

EXPERIMENTAL PROCEDURE:

1 connections are given as per the EXPERIMENTAL SETUP

2 Supply is switched ON after checking the connections.
3 Input voltage is set to 1V and by changing the input frequency,
output voltage is measured.
4 The procedure is applied to active low pass, high pass and
band pass filters.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 52

TABULATION –( ACTIVE BAND PASS FILTER):

Vin =

INPUT OUTPUT
FREQUENCY VOLTAGE GAIN =
S.NO. (Fi) (Vo) 20LOG(Vo/Vin)
Hz mV

MODEL GRAPH:
GAIN
(dB) MAX GAIN x 0.707
3 dB

FREQ.(Hz)
f1 f2

RESULT :
Thus the active low pass, high pass and band pass filters were designed and
tested using IC µA 741.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 53

CIRCUIT DIAGRAM-( ASTABLE MULTIVIBRATOR):

Vcc = 5V

1k Ra 8 4

7
I
C
5 3
Rb 5
1k 5
6
CRO

1µ C 92 1 5

C1= o.o1uf

DESIGN PROCEDURE:

 Duty cycle D = TON / (TON +TOFF)

= [0.693(Ra+Rb)C ] / [0.693(Ra+2Rb)C]
= _______________________________

 f = 1.45 / [(Ra+2Rb)C]
f = ________________________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 54

Ex. No :09
ASTABLE MULTIVIBRATOR AND MONOSTABLE
DATE : MULTIVIBRATOR USING 555 TIMERS

AIM:
To design and test astable and monostable multivibrator circuits using IC 555.
APPARATUS REQUIRED:
S.NO. APPARATUS RANGE QUANTITY
Dual power
1 (0 - +15)V 1
supply
2 Signal generator (0-1)MHz 1
3 CRO (0-30)MHz 1
4 IC IC 555 1
5 Resistor 1kΩ,2kΩ 1,1
6 Capacitor 0.1µf 1

THEORY:
ASTABLE MULTIVIBRATOR:
The astable multivibrator is also called the free running multivibrator. It has two
quasi states i.e. no stable states as such the circuit conditions oscillate between
the components values used to decide the time for which circuit remains in each
stable state. The principle of square wave output is to force the IC to operate in
saturation region. Whenever input at the negative input terminal just exceeds
Vref switching takes place resulting in a square wave output. In astable
multivibrator both stable states and one quasi states are present.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 55

TABULATION-( ASTABLE MULTIVIBRATOR):

AMPLITUDE TIME F =1/T

S.NO WAVEFORM (V) (T)
VOLTS ms Hz

1 CAPACITOR

2 OUTPUT

MODEL GRAPH:(ASTABLE MULTIVIBRATOR)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 56

CIRCUIT DIAGRAM- (MONOSTABLE MULTIVIBRATOR):

1k

-----
--

1µ

Design

T = 1.1*R*C, R = _________

= __________ C = ____________

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 57

MONOSTABLE MULTIVIBRATOR:

These multivibrators are comprised of group of regenerative circuits that

are commonly used in timing applications. The circuit produces a single pulse
of applied duration in response to each external trigger pulse. For each circuit
only one state exists. When an external trigger is applied the output changes its
state. The new state is called quasi-stable state.

EXPERIMENTAL PROCEDURE:
1 Connections are as per the EXPERIMENTAL SETUP.
2 Supply is switched ON after checking the connections.
3 For monostable multivibrator trigger pulse is given and for stable it is
not necessary.
4 Output square wave is noted from CRO.
5 The frequency is calculated by input.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 58

TABULATION –(MONOSTABLE MULTIVIBRATOR):

AMPLITUDE TIME FREQ.

S.NO. WAVEFORM (V) (T) f=1/T
VOLTS ms Hz

1
CAPACITOR

2 TRIGGER

OUTPUT
3

MODEL GRAPH-( MONOSTABLE MULTIVIBRATOR):

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 59

PIN DIAGRAM –( IC 555 TIMER ):

GND 1 8 +VCC

I
TRIGGER 2 7 DISCHARGE
C

5
3 5
OUTPUT 6 THRESHOLD
5

RESET 4 5 CONTROL
VOLTAGE

SPECIFICATIONS:

SUPPLY VOLTAGE : +5 V to +18 V

OPERATING TEMPERATURE : 00 TO 700 C

STORAGE TEMPERATURE
RANGE : 650 TO 1500 C

POWER DISSIPATION : 600mW

RESULT:
Thus the Astable and Monostable multivibrators were designed and tested
using IC555.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 60

PIN DIAGRAM-( LM565);

1 14 NC
V

2 13 NC
INPUT L

3 M 12 NC
INPUT
5
4 11 NC
VCO
OUTPUT 6
5 10 +V
5
PHASE
COMPARISON
INPUT 6 9 EXTERNAL C
FOR VCO

REF. OUTPUT 7 8 EXTERNAL R

FOR VCO
DEMOULATED
OUTPUT
SPECIFICATIONS:

MAXIMUM SUPPLY VOLTAGE : 2.6V

MAXIMUM POWER DISSIPATION : 330mW

SUPPLY CURRENT : 8mW

INPUT IMPEDENCE : 5KΩ

OUTPUT IMPEDENCE : 3.6KΩ

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 61

Ex. No :10
PLL CHARACTERISTICS AND FREQUENCY MULTIPLIER

DATE : USING PLL

AIM:
To conduct an experiment on PLL using IC LM 565 and to draw
the frequency response characteristics and also to design and to test the
frequency multiplier using PLL.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 CRO (0-30)MHz 1
3 IC LM 565 1
4 Resistor 20kΩ,2kΩ,4.7kΩ,10kΩ Each 2
6 Capacitor 0.01µf,0.001µf,10µf Each 1

THEORY:

The block diagram of LM565 PLL consists of base detector

amplifier. Low pass filter and VCO as shown in the block diagram. The phase
locked loop is not connected internally. It is necessary to connect output of
VCO (pin 4) to phase comparator in pin 5 externally.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 62

CIRCUIT DIAGRAM-(LM565):

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 63

In frequency multiplication applications a digital frequency driver is

inserted into loop between pin 4 and pin 5.the centre frequency of PLL is
determined by free running frequency multiplier of VCO given by free funning
frequency of VCO which is given by f0 = 1.2/(4R1C1) Hz. the value of Ri is
restricted from 2KΩ to 20KΩ but a capacitor can have any value. A capacitor
C2 is connected between pin 7 and to the positive supply from a first order low
pass filter with an external resistance of 3.6 KΩ. The value of filter capacitor C2
should be large enough to eliminate positive oscillator into VCO voltage.
FL = I.8fo/V Hz.
Where, fo = free running frequency in Hz
V = +V-(-V) volts
FL = ± (fo /2π3.6x103 C2)1/2
Where, C2 is in farads

EXPERIMENTAL PROCEDURE:

1. Connections are given as per the EXPERIMENTAL SETUP.

2. Observe the waveform at pin 4 and pin 5 without any input
signal. This is free running frequency of VCO (fo).
3. Switch ON the functional generator and give the square
waveform of 1Vpp & 1KHZ .
4. Calculate the capture range and lock range.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 64

TABULATION –(FREQUENCY MULTIPLICATION ):

FREQUENY AMPLITUDE
F=1/T (V)
S.NO. WAVEFORM
HZ volts

INPUT
1

OUTPUT
2

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 65

MODEL GRAPH:

Lock range
Vo in V

Capture range

FREQ. IN Hz

F4 F1fo F3 F2

FL1
FL1

RESULT:

Thus the experiment on LM 565 is conducted and the frequency

response characteristic is drawn.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 66

PIN DIAGRAM-(LM 723):

1 14 NC
NC

2 13 FREQUENCY
CURRENT LIMIT L COMPARATOR

3 M 12
CURRENTSENSE +VCC

INVERTING 7
4 11 VC
INPUT
2
5 10 OUTPUT
NONINVERTING 3
INPUT
6 9 VZ
VREF

-VCC NC
7 8

SPECIFICATIONS:

PEAK VOLTAGE FROM +VCC TO –VCC : 50V

CONTINUOUS VOLTAGE FROM +VCC TO –VCC : 40V

INPUT TO OUTPUT VOLTAGE DIFFERENTIAL : 40V

DIFFERENTIAL INPUT VOLTAGE TO ERROR

AMLIFIER : ±5V

VOLTAGE BETWEEN NON-INVERTING INPUTS

& -VCC : 8V

CURRENT FROM VZ : 25mA

CURRENT FROM VREF : 15m

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 67

Ex. No :11
DC POWER SUPPLY USING LM 723
DATE :

AIM:
To conduct an experiment in order to get regulated power supply
output using LM 723.
APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
5.5KΩ ,
2 Resistor Each 1
1KΩ,846Ω
3 Capacitor 100pF 1
4 Bread Board - 1
5 Volt meter (0-30)V 1

THEORY:
The basic voltage regulator in its simplest form consists of a) voltage
reference Vr b) error amplifier c) feedback network d) active series or shunt
control unit. the voltage reference generates a voltage level which is applied to
the comparator circuit, which is generally error amplifier. The second input to
the error amplifier obtained through feedback network. Generally using the
potential divider, the feedback signal is derived by sampling the output voltage.
The error amplifier converts the difference between the output sample and the
reference voltage into an error signal. This error signal in turn controls the
active element of the regulator circuit, in order to compensate the changes in the
output voltage. Such an active element is generally a transistor.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 68

CIRCUIT DIAGRAM –(DC POWER SUPPLY);

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 69

Let , Error amplifier controls the series pass transistor Q2 which acts
as a variable resistor. The series pass transistor is small power transistor having
about 800mW power dissipation. The unregulated power supply source of
(< 36 V d.c) is connected to collector of series pass transistor.
Transistor Q2 acts as current limiter in case of short circuit condition.
It senses drop across Rsc placed in series with regulated output voltage
externally.
The frequency compensation terminal controls the frequency
response of the error amplifier. The required roll-off is obtained by connecting a
small capacitor of 100pF between frequency compensation and inverting input
terminals.

EXPERIMENTAL PROCEDURE:

1 Connections are given as per the EXPERIMENTAL SETUP.

2 The input voltage is given to the circuit and the output voltage slowly
varies from zero.
3 Then the output voltage attains the designed value and then it is
irrespective of input voltage (the output becomes constant).

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 70

TABULATION–(DC POWER SUPPLY):

Vin Vo
S.NO.
Volts Volts

Vo(V)

Vin vs Vo

Vin(V)

RESULT:
Thus the experiment is conducted using LM 723 and so the regulated
output is obtained using the circuit.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 71

PIN DIAGRAM:

SPECIFICATIONS:

MINIMUM OUTPUT VOLTAGE : 1.2 V

MAXIMUM OUTPUT VOLTAGE : 57 V

MAXIMUM OUTPUT CURRENT : 1.5mA

OUTPUT RESISTANCE : 17MΩ

RIPPLE REGECTION : 62 dB

SHORT CIRCUIT CURRENT : 750mA

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 72

Ex. No :12
DC POWER SUPPLY USING LM 317
DATE :

AIM:

To conduct an experiment in order to get regulated output using

LM 317.

APPARATUS REQUIRED:

S.NO. APPARATUS RANGE QUANTITY

Dual power
1 (0 - +15)V 1
supply
2 Resistor 240Ω , 1.4KΩ, Each 1
3 Capacitor 1µF 1
4 Bread Board - 1

THEORY:

The basic voltage regulator in its simplest form consists of a) voltage

reference Vr b) error amplifier c) feedback network d) active series or shunt
control unit. the voltage reference generates a voltage level which is applied to
the comparator circuit, which is generally error amplifier. The second input to
the error amplifier obtained through feedback network. Generally using the
potential divider, the feedback signal is derived by sampling the output voltage.
The error amplifier converts the difference between the output sample and the
reference voltage into an error signal. This error signal in turn controls the
active element of the regulator circuit, in order to compensate the changes in the
output voltage. Such an active element is generally a transistor.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 73

CIRCUIT DIAGRAM-(LM317):

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 74

DESIGN PROCEDURE:

 V o = 1.25(1+R2/R1)

Besides fixed voltage regulator, Ic voltage regulators are available which

allow the adjustment of the output voltage. The output voltage can be adjusted
from 1.2V to as high as 5.7V with the help of such regulators. in such regulator
IC’s common terminal plays the role of control input and hence called as
adjustment terminal. The LM 317 series is the most commonly used three
terminal adjustable regulators. These devices are available in a variety of
packages which can be easily mounted and handled. The power rating of such
regulators is 1.5Am.the maximum input voltage of LM 317 is 40V

EXPERIMENTAL PROCEDURE:

4 Connections are given as per the experimental setup.

5 The input voltage is given to the circuit and the output voltage slowly
varies from zero.
6 Then the output voltage attains the designed value and then it is
irrespective of input voltage (the output becomes constant).

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 75

TABULATION-(DC POWER SUPPLY):

Vin Vo
S.NO.
volts volts

MODEL GRAPH:

Vo(V)

Vin vs Vo

Vin(V)

RESULT :

Thus the experiment is conducted using LM 317 and so the regulated

output is obtained using the circuit

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 76

BLOCK DIAGRAM-(SMPS):

BLOCK DIAGRAM ELEMENTS ARE:

1.Rectifier
2.Transformer
3.Filter
4.Pwm Oscillator
5.Amplifier
6.Isolation

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 77

Ex. No :13

STUDY OF SMPS (SG 3524 AND SG 3525)

DATE :

AIM:

To study in detail about SMPS control unit of SG 3524 and SG 3525.

APPARATUS REQUIRED:

S.NO. APPARATUS QUANTITY

1 SMPS board 1
SG 3524 /
2 1
SG 3525
3 RPS (0-30)V 1

DESCRIPTION:

The monolithic Ic contains all the control circuitry for a regulating power
supply inverter or switching regulator. It also includes the error amplifier,
oscillator, pulse width modulator, pulse steering flip flop, dual alternating
output switches and current limiting and shut down circuitry.

The device can be used for switching regulators of either polarity,

transformer coupled AC to DC converters, transformations, voltage doubling
and polarity converters as well as other power control applications of 00C to
700C.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 78

FEATURES:

 Complete PWM power control circuitry.

 Single ended or push pull outputs
 Line and load regulation of 0.2%
 1 % maximum temperature variations.
 Total supply current is less than 10mA.
 Operation beyond 100 KHz.

CURRENT LIMITING:

The current limiting circuitry of the SG3524 is shown in the figure. By

matching the base-emitter voltages of Q1 and Q2 and also assuming a negligible
voltage drop across the R1,

Threshold = VBE(Q1) +I1R2-VBE(Q2)

= I1R2-200mV

Although this circuit provides a relatively small threshold with a

negligible temperature coefficient, there are some limitations to its use. The
most important of which is ±1V common mode range which require sensing in
the ground state. Another factor to consider is that the frequency compensation
provided by R1C1 and Q1 provides a roll off pole at approximately 300Hz.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 79

CURRENT LIMITING CIRCUITRY OF SG 3524

RAMP

I1
COMPENSATOR
ERROR AMPLIFIER
C1

R1

Q1

R1
Q2

5
+ - 4

SENSE

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 80

Since the gain of this circuit is relatively low, there is a transition region as
the current limit amplifier takes over pulse width control from the error
amplifier. For testing purposes threshold is defined as the input voltage required
getting 25% duty cycle with the error amplifier signaling maximum duty cycle

THEORY OF OPERATION:

VOLTAGE REFERENCE:

All the internal series regulator provides a nominal 5V output which is used
both to generate source for all the internal timing and controlling circuitry. this
regulator may be bypassed for operation from a fixed 5V supply by connecting
pins 15 and 16 together to the input voltage of 5V
This reference regulator may be used as a 5V source for other circuitry. It
will provide up to 50mA of current itself and can easily be expanded to higher
currents with an external PNP.

EXTERNAL SYNCHRONIZATION:

If it is designed to synchronies the SG 3524 to an external clock, a pulse

of approximately ±13V may be applied to the oscillator output terminal with
RTCTat slightly greater than the clock pulse. the same consideration of pulse
width is applied. The impedances to ground at this point is approximately 2KΩ.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 81

EXPANDED REFERENCE CURRENT CAPABILITY

Q1

16
100Ω SG 3524
Vin Vref
REFERENCE
SECTION

15

8 10µF
-
GND

IL OF 1Amp DEPENDING
ON CHOICE FOR Q1

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 82

If the two or more SG 3524 must be synchronized together, one must be

designed at master with it.RTCT set for the correct period. the slaves should each
have all RTCT set for approximately 10%. Layer period than the master with the
added requirement that CT(slave) = one half CT(master).then connecting pins on
he all units together will ensure that the master output pulse, which occurs first
and has a wide pulse width will reset the slave units.

ERROR AMPLIFIER:

This circuitry is a simple differential input transconductance amplifier.

the output is the compensation terminal pin 9 which is a higher impedance
mode (RLCTMΩ).the gain is Av-gmRL-8IcRL/2KT = 0.002 RL and can be easily
be reduced from a nominal of 10,000 by an external shunt impedance shunt
resistance from pin 9 to ground.

In addition to DC gain control, the compensation terminal is also the

place for AC phase compensation.

Typically most output filter designs will introduce one or more additional
poles at a significantly lower frequency .therefore, the best stabilizing network
is a series RC combination between pin 9 and ground which introduces a zero to
cause one of the output filter poles. A good starting point is 50KΩ plus
0.001µF.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 83

TEST CIRCUIT-(SMPS);

RESULT :

Thus the SMPS control unit of SG 3524 was studied.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 84

CIRCUIT DIAGRAM –( INSTRUMENTATION AMPLIFIER):

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 85

Ex. No :14
SIMULATION OF INSTRUMENTATION AMPLIFIER USING PSPICE
DATE :

AIM:
To simulate and analyze the instrumentation amplifier using PSPICE.

SOFTWARE REQUIRED:

Or CAD SOFTWARE

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE icon.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig .
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

RESULT:
Thus the instrumentation amplifier using PSPICE was simulated and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 86

CIRCUIT DIAGRAM-(FILTERS):

LOW PASS FILTER:

HIGH PASS FILTER:

BAND PASS FILTER

Ri 10kΩ Rf
Ri RF
10kΩ
R1
2 -
0.01 µF 2 -
3 +
3 + 741 Vout
741 C1
~ C2 R2
0.01 µF
Vin

GAIN
(dB) MAX GAIN x 0.707

FREQ.(Hz)
f1 f2
www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 87

Ex. No :15
SIMULATION OF ACTIVE LOWPASS, HIGHPASS AND BANDPASS
DATE :
FILTERS USING PSPICE

AIM:
To simulate and analyze the Active Low pass, High pass and Band pass
Filters using PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE icon.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

RESULT:

Thus the Active Low pass, High pass and Band pass Filters using
PSPICE was simulated and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
 EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 88

CIRCUIT DIAGRM-(ASTABLE MULTIVIBRATOR):

MODEL GRAPH:

Vo(V)

Vsat

+βVsat
TIME (ms)

–βVsat

–Vsat

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 89

Ex. No :16
SIMULATION OF ASTABLE & MONOSTABLE
MULTIVIBRATORS AND SCHMITT TRIGGER USING PSPICE
DATE :

AIM:

To simulate and analyze the Astable &Monostable Multivibrators and

Schmitt Trigger using PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE ion.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 90

CIRCUIT DIAGRAM-(MONOSTABLE MULTIVIBRATOR):

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 91

CIRCUIT DIAGRAM-(SCHMITT TRIGER):

MODEL GRAPH:

RESULT:
Thus the Astable & MonostableMultivibrators and Schmitt Trigger using
PSPICE was simulated and tested

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 92

CIRCUIT DIAGRAM-( RC PHASE SHIFT OSCILLATOR):

Rf

+15 V
R1
2 7
6
ICµA
741
4 CRO
3
Rc -15 V

C C C

R R R

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 93

Ex. No :17
SIMULATION OF PHASE SHIFT AND WEIN BRIDGE
OSCILLATORS USING PSPICE
DATE :

AIM:
To simulate and analyze the Phase Shift and Wein Bridge Oscillators
using op-amp using PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE ion.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 94

CIRCUIT DIAGRAM-(WEIN BRIDGE OSCILLATOR):

MODEL GRAPH:

AMP(V)
RC PHASE SHIFT OSCILLATOR

TIME(ms)

AMP(V)

WIEN BRIDGE OSCILLATOR

TIME(ms)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 95

RESULT:

Thus the Phase Shift and Wein Bridge Oscillators using op-amp using
PSPICE was simulated and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 96

CIRCUIT DIAGRAM-(ASTABLE MULTIVIBRATOR):

Vcc = 5V

Ra 8
4
7
I
C
3
5
Rb 5
5
CRO
6
2 1 5

MODEL GRAPH:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 97

Ex. No :18
SIMULATION OF ASTABLE AND MONOSTABLE
MULTIVIBRATORS (USING NE 555 TIMER) USING PSPICE
DATE :

AIM:
To simulate and analyze the Astable and monostable multivibrators using
NE555 Timer using PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE ion.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 98

CIRCUIT DIAGRAM-(MONOSTABLE MULTIVIBRATOR):

-----
--

SIMULATION OUTPUT:

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 99

RESULT:

Thus the Astable and Monostable Multivibrators using NE555 Timer

using PSPICE was simulated and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 100

CIRCUIT DIAGRAM-(ANALOG TO DIGITAL CONVERTER):

CIRCUIT DIAGRAM-(DIGITAL TO ANALOG CONVERTER):

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 101

Ex. No :19
SIMULATION OF ADC, DAC AND ANOLOG MULTIPLIER USING
PSPICE
DATE :

AIM:
To simulate and analyse the ADC, DAC& Anolog Multiplier using
PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE ion.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
 Verify the simulated output and take a print out.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 102

ANALOG MULTIPLIER:

RESULT:

Thus the ADC, DAC, & Anolog Multiplier using PSPICE was simulated
and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 103

CIRCUIT DIAGRAM –(CMOS INVERTER):

CIRCUIT DIAGRAM-(CMOS NOR)

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 104

Ex. No :20
SIMULATION OF CMOS INVERTER,NAND, AND NOR
USING PSPICE
DATE :

AIM:
To simulate and analyze the CMOS inverter,NAND,NOR using
PSPICE.

SOFTWARE REQUIRED:

Or CAD software.

PROCEDURE:

 Switch on the computer and select ORCAD PSPICE ion.

 Open a new project to design a circuit in the file menu.
 Select the required components from the library.
 Draw the circuit as shown in Fig (1) &(2) tool bar.
 After completing save the project and go to simulation tool bar
Verify the simulated output and take a print out

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
EC6412 LINEAR INTEGRATED CIRCUITS LABORATORY 105

CIRCUIT DIAGRAM-(CMOS NAND)

RESULT:

Thus the CMOS inverter, NAND, NOR using PSPICE was simulated
and tested.

www.BrainKart.com
VVIT DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
Click below buttons to visit particular Department