Front cover

Tivoli Storage Productivity

Center for Replication for
Open Systems
Master Tivoli Storage Productivity
Center for Replication in open systems

Manage replication services from

one interface

Use all of the latest copy

services features

Karen Orlando
Otavio Rocha Filho
Danijel Paulin
Antonio Rainero
Deborah Sparks

ibm.com/redbooks
International Technical Support Organization

Tivoli Storage Productivity Center for Replication for

Open Systems

January 2014

SG24-8149-00
 Note: Before using this information and the product it supports, read the information in “Notices” on
page ix.

First Edition (Janury 2014)

This edition applies to Tivoli Storage Productivity Center for replication Version 5, Release 2

© Copyright International Business Machines Corporation 2014. All rights reserved.

Note to U.S. Government Users Restricted Rights -- Use, duplication or disclosure restricted by GSA ADP Schedule
Contract with IBM Corp.
Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Authors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Now you can become a published author, too! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Comments welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Stay connected to IBM Redbooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication . . . . . . . 1

1.1 Tivoli Storage Productivity Center for Replication overview . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Copy services overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5 Session types and usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5.1 Practice sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.2 Data copying symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.3 FlashCopy sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.4 Snapshot sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.5.5 Metro Mirror Single Direction sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.5.6 Metro Mirror Failover/Failback sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.5.7 Metro Mirror Failover/Failback with Practice sessions . . . . . . . . . . . . . . . . . . . . . 14
1.5.8 Global Mirror Single Direction sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.5.9 Global Mirror Failover/Failback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.5.10 Global Mirror Failover/Failback with Change Volumes sessions . . . . . . . . . . . . 16
1.5.11 Global Mirror Failover/Failback with Practice sessions. . . . . . . . . . . . . . . . . . . . 16
1.5.12 Global Mirror Either Direction with Two-Site Practice sessions . . . . . . . . . . . . . 17
1.5.13 Metro Global Mirror sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.5.14 Metro Global Mirror with Practice sessions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.5.15 Session states. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.5.16 Session commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.6 New features and enhancements in Tivoli Storage Replication Center for Replication by
release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.6.1 New in V5.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.6.2 New in V5.1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.6.3 New in V5.1.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.6.4 New in V5.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.7 Introduction to Storage Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.7.1 IBM System Storage DS8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.7.2 IBM Storwize Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.7.3 IBM XIV Storage System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 2. Planning and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.1 Tivoli Storage Productivity Center for Replication installation planning . . . . . . . . . . . . 38
2.1.1 Pre-installation steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.1.2 Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.1.3 Hardware and software requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.1.4 Configuration planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.1.5 User accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

© Copyright IBM Corp. 2014. All rights reserved. iii

 2.1.6 HyperSwap configuration for z/OS and Open systems. . . . . . . . . . . . . . . . . . . . . 45
2.2 Installing Tivoli Storage Productivity Center for Replication . . . . . . . . . . . . . . . . . . . . . 47
2.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
2.2.2 Tivoli Storage Productivity Center installation packages . . . . . . . . . . . . . . . . . . . 48
2.2.3 Tivoli Storage Productivity Center installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Chapter 3. General administration and high availability . . . . . . . . . . . . . . . . . . . . . . . . 61

3.1 Accessing Tivoli Storage Productivity Center for Replication . . . . . . . . . . . . . . . . . . . . 63
3.1.1 Accessing Tivoli Storage Productivity Center for Replication GUI . . . . . . . . . . . . 63
3.1.2 Accessing Tivoli Storage Productivity Center for Replication CLI. . . . . . . . . . . . . 65
3.2 GUI overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
3.2.1 GUI panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
3.3 CLI Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.3.1 Configuring the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
3.3.2 Setting up automatic login to the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.3.3 Remote CLI installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.3.4 CLI automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
3.4 Tivoli Storage Productivity Center for Replication interaction with Tivoli Storage
Productivity Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
3.5 Tivoli Storage Productivity Center for Replication security and user administration . . . 93
3.5.1 Adding Tivoli Storage Productivity Center users and groups to Tivoli Storage
Productivity Center for Replication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
3.5.2 Tivoli Storage Productivity Center for Replication role-based access control. . . . 94
3.5.3 Managing user access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
3.5.4 Modifying access to a user role. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
3.5.5 Removing access to a user role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
3.6 Tivoli Storage Productivity Center for Replication advanced tools . . . . . . . . . . . . . . . 100
3.6.1 Packaging log files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
3.6.2 Setting the auto refresh rate for the browser. . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
3.6.3 Managing the Metro Mirror heartbeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
3.7 Tivoli Storage Productivity Center for Replication Console. . . . . . . . . . . . . . . . . . . . . 103
3.8 Tivoli Storage Productivity Center for Replication High Availability. . . . . . . . . . . . . . . 106
3.8.1 Setting up a Tivoli Storage Productivity Center for Replication standby server . 107
3.8.2 Takeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
3.8.3 Best practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
3.9 Starting and stopping the Tivoli Storage Productivity Center for Replication server . . 123
3.9.1 Verifying the status of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
3.9.2 Starting and stopping Tivoli Storage Productivity Center for Replication . . . . . . 127
3.10 Using CSV files for importing and exporting sessions. . . . . . . . . . . . . . . . . . . . . . . . 129
3.10.1 Exporting CSV files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
3.10.2 Importing CSV files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
3.10.3 Working with CSV files under Microsoft Excel . . . . . . . . . . . . . . . . . . . . . . . . . 139
3.11 Backing up and restoring a repository. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
3.12 Tivoli Storage Productivity Center for Replication SNMP management . . . . . . . . . . 144
3.12.1 SNMP Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
3.12.2 SNMP setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
3.13 Adding and connecting to storage systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
3.13.1 DS8000 Connection page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
3.13.2 XIV System Storage Connection window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
3.14 Adding and connecting host systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
3.14.1 AIX Host System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
3.14.2 z/OS Host System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

iv Tivoli Storage Productivity Center for Replication for Open Systems

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000. . 159
4.1 Capabilities overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
4.1.1 FlashCopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
4.1.2 Metro Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
4.1.3 Global Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
4.1.4 Metro Global Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
4.2 New functions for DS8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
4.2.1 FlashCopy consistency groups for FlashCopy sessions. . . . . . . . . . . . . . . . . . . 182
4.2.2 Global Mirror pause with consistency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
4.2.3 Easy Tier Heat Map Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
4.2.4 Global Mirror Info Tab for DS8000 sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
4.2.5 Global Mirror Historical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
4.2.6 Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication
for Open Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
4.3 Managing DS8000 sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
4.3.1 DS8000 Path management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
4.3.2 Setting up a session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
4.3.3 Session tunable parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
4.3.4 Scenarios requiring a full copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
4.4 Use cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
4.4.1 Practicing disaster recovery by using FlashCopy sessions . . . . . . . . . . . . . . . . 251
4.4.2 Two-site planned outages scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
4.4.3 Three-site planned outages scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
4.5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
4.5.1 Managing loss of connection to storage system . . . . . . . . . . . . . . . . . . . . . . . . . 270
4.5.2 Managing suspending events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume
Controller and Storwize family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
5.1.1 The Storwize family of Storage Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
5.1.2 Tivoli Storage Productivity Center for Replication and the Storwize family. . . . . 281
5.2 SAN Volume Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
5.3 Storwize Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
5.3.1 Storwize V7000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
5.3.2 Storwize V7000 Unified. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
5.3.3 Storwize V3700 and V3500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
5.4 New Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
5.4.1 Global Mirror Failover/Failback with Change Volumes session . . . . . . . . . . . . . 287
5.4.2 Support for the SAN Volume Controller 6.4 option to move volumes between I/O
groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
5.5 Session Types and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
5.5.1 FlashCopy sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
5.5.2 Metro Mirror sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
5.5.3 Global Mirror sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
5.6 Why and when to use certain session types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
5.6.1 When to use FlashCopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
5.6.2 When to use Metro Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
5.6.3 When to use Global Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
5.7 Disaster Recovery use cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
5.7.1 SAN Volume Controller Stretched Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
5.7.2 Global Mirror Forwarding I/O Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
5.8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307

Contents v
 5.8.1 Storwize family replication error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
5.8.2 Troubleshooting replication links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV . . . . . 311
6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
6.1.1 XIV consistency groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
6.1.2 XIV connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
6.2 XIV session types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
6.2.1 Snapshot sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
6.2.2 Metro Mirror Failover/Failback sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
6.2.3 Global Mirror Failover/Failback sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
6.3 Adding XIV volume protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
6.4 Disaster Recovery use cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
6.5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for
Replication for Open Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
7.1 Overview of z/OS HyperSwap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
7.2 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
7.2.1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
7.2.2 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
7.2.3 Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
7.2.4 Enabling a host name or IP address connection to a z/OS host system . . . . . . 359
7.2.5 Enabling z/OS HyperSwap and adding a Tivoli Storage Productivity Center for
Replication user to z/OS host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
7.3 z/OS HyperSwap sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
7.3.1 Basic HyperSwap sessions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
7.3.2 HyperSwap enabled Metro Mirror Failover/Failback sessions . . . . . . . . . . . . . . 361
7.3.3 HyperSwap enabled Metro Global Mirror sessions. . . . . . . . . . . . . . . . . . . . . . . 362
7.3.4 HyperSwap enabled Metro Global Mirror with Practice sessions . . . . . . . . . . . . 366
7.3.5 Hardened Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
7.4 Description and usage of HyperSwap enabled sessions . . . . . . . . . . . . . . . . . . . . . . 369
7.4.1 Setting up a HyperSwap enabled session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
7.5 Use cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381

Chapter 8. Hints and tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389

8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
8.2 VMware, DS8000, and Tivoli Storage Productivity Center for Replication . . . . . . . . . 390
8.2.1 Hosting by using virtual servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
8.2.2 VAAI and DS8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
8.3 DS8000 LSS symmetry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
8.4 HyperSwap enabled sessions troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
8.5 Stuck in a particular state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
8.6 High availability server platforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
8.7 Simple Network Management Protocol setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
8.8 Tivoli Storage Productivity Center for Replication logging . . . . . . . . . . . . . . . . . . . . . 395
8.8.1 Collecting logs by using GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
8.8.2 Collecting logs by using CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
8.8.3 Collecting logs manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
8.9 Auto refresh rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
8.10 User authentication issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
8.10.1 An error is displayed when you try to log on . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
8.10.2 An error occurs when you try to add a user . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
8.11 IBM Software Support Lifecycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397

vi Tivoli Storage Productivity Center for Replication for Open Systems

8.12 Tivoli Storage Productivity Center support matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

Appendix A. Tivoli Storage Productivity Center for Replication and Advanced Copy
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
A.1 Integration with Tivoli Storage Productivity Center for Replication . . . . . . . . . . . . . . . 400

Appendix B. Tivoli Storage Productivity Center for Replication integration. . . . . . . 403

B.1 Integration with Tivoli Storage Productivity Center for Replication . . . . . . . . . . . . . . . 404

Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407

IBM Redbooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
Other publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
Online resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
Help from IBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408

Contents vii
viii Tivoli Storage Productivity Center for Replication for Open Systems
Notices

This information was developed for products and services offered in the U.S.A.

IBM may not offer the products, services, or features discussed in this document in other countries. Consult
your local IBM representative for information on the products and services currently available in your area. Any
reference to an IBM product, program, or service is not intended to state or imply that only that IBM product,
program, or service may be used. Any functionally equivalent product, program, or service that does not
infringe any IBM intellectual property right may be used instead. However, it is the user's responsibility to
evaluate and verify the operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter described in this document. The
furnishing of this document does not grant you any license to these patents. You can send license inquiries, in
writing, to:
IBM Director of Licensing, IBM Corporation, North Castle Drive, Armonk, NY 10504-1785 U.S.A.

The following paragraph does not apply to the United Kingdom or any other country where such
provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION
PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of
express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made
to the information herein; these changes will be incorporated in new editions of the publication. IBM may make
improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time
without notice.

Any references in this information to non-IBM websites are provided for convenience only and do not in any
manner serve as an endorsement of those websites. The materials at those websites are not part of the
materials for this IBM product and use of those websites is at your own risk.

IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring
any obligation to you.

Any performance data contained herein was determined in a controlled environment. Therefore, the results
obtained in other operating environments may vary significantly. Some measurements may have been made
on development-level systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.

Information concerning non-IBM products was obtained from the suppliers of those products, their published
announcements or other publicly available sources. IBM has not tested those products and cannot confirm the
accuracy of performance, compatibility or any other claims related to non-IBM products. Questions on the
capabilities of non-IBM products should be addressed to the suppliers of those products.

This information contains examples of data and reports used in daily business operations. To illustrate them
as completely as possible, the examples include the names of individuals, companies, brands, and products.
All of these names are fictitious and any similarity to the names and addresses used by an actual business
enterprise is entirely coincidental.

COPYRIGHT LICENSE:

This information contains sample application programs in source language, which illustrate programming
techniques on various operating platforms. You may copy, modify, and distribute these sample programs in
any form without payment to IBM, for the purposes of developing, using, marketing or distributing application
programs conforming to the application programming interface for the operating platform for which the sample
programs are written. These examples have not been thoroughly tested under all conditions. IBM, therefore,
cannot guarantee or imply reliability, serviceability, or function of these programs.

© Copyright IBM Corp. 2014. All rights reserved. ix

Trademarks
IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business Machines
Corporation in the United States, other countries, or both. These and other IBM trademarked terms are
marked on their first occurrence in this information with the appropriate symbol (® or ™), indicating US
registered or common law trademarks owned by IBM at the time this information was published. Such
trademarks may also be registered or common law trademarks in other countries. A current list of IBM
trademarks is available on the Web at http://www.ibm.com/legal/copytrade.shtml

The following terms are trademarks of the International Business Machines Corporation in the United States,
other countries, or both:
AIX® IBM Flex System™ Redbooks (logo) ®
Cognos® IBM SmartCloud® Storwize®
DB2® Jazz™ System Storage®
DS6000™ MVS™ System z®
DS8000® Parallel Sysplex® Tivoli®
Easy Tier® POWER7® WebSphere®
Enterprise Storage Server® PowerHA® XIV®
FICON® PureFlex™ xSeries®
FlashCopy® RACF® z/OS®
HyperSwap® Real-time Compression™
IBM® Redbooks®

The following terms are trademarks of other companies:

Intel, Intel Xeon, Intel logo, Intel Inside logo, and Intel Centrino logo are trademarks or registered trademarks
of Intel Corporation or its subsidiaries in the United States and other countries.

ITIL is a registered trademark, and a registered community trademark of The Minister for the Cabinet Office,
and is registered in the U.S. Patent and Trademark Office.

Linux is a trademark of Linus Torvalds in the United States, other countries, or both.

Microsoft, Windows, and the Windows logo are trademarks of Microsoft Corporation in the United States,
other countries, or both.

UNIX is a registered trademark of The Open Group in the United States and other countries.

Other company, product, or service names may be trademarks or service marks of others.

x Tivoli Storage Productivity Center for Replication for Open Systems

Preface

This IBM® Redbooks® publication for the Tivoli® Storage Productivity Center for Replication
for the Open environment walks you through the process of establishing sessions, and
managing and monitoring copy services through Tivoli Storage Productivity Center for
Replication. The book introduces enhanced copy services and new session types that are
used by the latest IBM storage systems. Tips and guidance for session usage, tunable
parameters, troubleshooting, and for implementing and managing Tivoli Storage Productivity
Center for Replication’s latest functionality up to v5.2 also are provided. Tivoli Storage
Productivity Center for Replication’s integration and latest functionality includes Global Mirror
Pause with Consistency, Easy Tier® Heat Map Transfer, and IBM System Storage® SAN
Volume Controller Change Volumes. As of v5.2, you can now manage z/OS® Hyperswap
function from an Open System.

IBM Tivoli Storage Productivity Center for Replication for Open Systems manages copy
services in storage environments. Copy services are used by storage systems, such as IBM
System Storage DS8000®, SAN Volume Controller, IBM Storwize® V3700, V3500, V7000,
V7000 Unified, and IBM XIV® Storage systems to configure, manage, and monitor data-copy
functions. Copy services include IBM FlashCopy®, Metro Mirror, Global Mirror, and Metro
Global Mirror.

This IBM Redbooks publication is the companion to the draft of the IBM Redbooks publication
Tivoli Storage Productivity Center V5.2 Release Guide, SG24-8204. It is intended for storage
administrators who ordered and installed Tivoli Storage Productivity Center version 5.2 and
are ready to customize Tivoli Storage Productivity Center for Replication and connected
storage. This publication also is for anyone that wants to learn more about Tivoli Storage
Productivity Center for Replication in an open systems environment.

© Copyright IBM Corp. 2014. All rights reserved. xi

Authors
This book was produced by a team of specialists from around the world working at the
International Technical Support Organization, Poughkeepsie Center.

Karen Orlando is a Project Leader at the International

Technical Support Organization, Tucson Arizona Center. Karen
has over 25 years in the IT industry with extensive experience
in open systems management, and Information and Software
development of IBM hardware and software storage. She holds
a degree in Business Information Systems from the University
of Phoenix and is Project Management Professional (PMP),
certified since 2005.

Otavio Rocha Filho is a SAN Storage IT Specialist for

Strategic Outsourcing, IBM Brazil Global Delivery Center in
Hortolandia. He has over 25 years of experience in IT, with the
last 15 years dedicated to Data Storage solutions. He holds a
bachelors degree in Electrical Engineering from the University
of Sao Paulo, an MBA from Insper, and professional
certifications including IBM Level 2 IT Specialist, Brocade SAN
Manager, and ITIL Foundations. He has written extensively
about IBM SAN Volume Controller, the Storwize family, and
SAN Storage Best Practices. His areas of expertise also
include Systems Performance and IT Services Delivery.

Danijel Paulin is a Systems Architect in IBM Croatia, working

for the Systems Architect team in IBM South East Europe
region. He has 15 years of experience in IT. Before joining IBM
Croatia in 2003, he worked for two financial companies in
Croatia and he was responsible for IBM mainframe and storage
administration. He has experience with various IBM storage
products and storage software. His areas of expertise include
architecture and design of various HA/DR/BC solutions for
mainframe and open systems.

Antonio Rainero is a Certified IT Specialist working for the

Integrated Technology Services organization in IBM Italy. He
joined IBM in 1998 and has more than 10 years of experience
in the delivery of storage services for z/OS and Open Systems
clients. His areas of expertise include storage subsystems
implementation, performance analysis, SANs, storage
virtualization, disaster recovery, and high availability solutions.
He co-authored several IBM Redbooks publications. Antonio
holds a degree in Computer Science from University of Udine,
Italy.

xii Tivoli Storage Productivity Center for Replication for Open Systems
 Deborah Sparks is a technical writer for IBM in the United
States. She has 20 years experience in the field. She holds a
degree in Communications and Journalism from California
State University, Sacramento, and a credential in technical
writing from San Jose State University. Her areas of expertise
include writing, editing, and documentation management. She
has been with IBM for seven years, during which time she has
written extensively on Tivoli Storage Productivity Center and
Tivoli Storage Productivity Center for Replication.

Thanks to the following people for their contributions to this project:

Mary Lovelace
International Technical Support Organization, Poughkeepsie Center

򐂰 Randy Blea
򐂰 Jay Calder
򐂰 Steven Kern
򐂰 Khang N. Nguyen
򐂰 Pam Schull
򐂰 Damian Trujilo
򐂰 Wayne Sun
IBM Tucson

Bill Rooney
IBM Poughkeepsie

Selwyn Dickey
IBM Rochester

Todd Gerlach
IBM Austin

Sudhir Koka
IBM San Jose

Preface xiii
Now you can become a published author, too!

Here’s an opportunity to spotlight your skills, grow your career, and become a published
author—all at the same time! Join an ITSO residency project and help write a book in your
area of expertise, while honing your experience using leading-edge technologies. Your efforts
will help to increase product acceptance and customer satisfaction, as you expand your
network of technical contacts and relationships. Residencies run from two to six weeks in
length, and you can participate either in person or as a remote resident working from your
home base.

Find out more about the residency program, browse the residency index, and apply online at
this website:
http://www.ibm.com/redbooks/residencies.html

Comments welcome
Your comments are important to us!

We want our books to be as helpful as possible. Send us your comments about this book or
other IBM Redbooks publications in one of the following ways:
򐂰 Use the online Contact us review Redbooks form that is found at:
http://www.ibm.com/redbooks
򐂰 Send your comments in an email to:
[email protected]
򐂰 Mail your comments to:
IBM Corporation, International Technical Support Organization
Dept. HYTD Mail Station P099
2455 South Road
Poughkeepsie, NY 12601-5400

Stay connected to IBM Redbooks

򐂰 Find us on Facebook:
http://www.facebook.com/IBMRedbooks
򐂰 Follow us on Twitter:
http://twitter.com/ibmredbooks
򐂰 Look for us on LinkedIn:
http://www.linkedin.com/groups?home=&gid=2130806
򐂰 Explore new Redbooks publications, residencies, and workshops with the IBM Redbooks
weekly newsletter:
https://www.redbooks.ibm.com/Redbooks.nsf/subscribe?OpenForm
򐂰 Stay current on recent Redbooks publications with RSS Feeds:
http://www.redbooks.ibm.com/rss.html

xiv Tivoli Storage Productivity Center for Replication for Open Systems
 1

Chapter 1. Introduction to Tivoli Storage

Productivity Center for
Replication
This chapter provides an overview of IBM Tivoli Storage Productivity Center for Replication
for open systems. It reviews copy services functions and then describes how they are
implemented in Tivoli Storage Productivity Center for Replication.

We introduce Tivoli Storage Productivity Center for Replication key concepts, architecture,
session types and usage, and new functionality as of IBM Tivoli Storage Productivity Center
version 5.1. We also introduce storage systems that are supported by Tivoli Storage
Productivity Center for Replication.

This chapter includes the following topics:

򐂰 Tivoli Storage Productivity Center for Replication overview
򐂰 Terminology
򐂰 Architecture
򐂰 Copy services overview
򐂰 Session types and usage
򐂰 New features and enhancements in Tivoli Storage Replication Center for Replication by
release
򐂰 Introduction to Storage Systems

© Copyright IBM Corp. 2014. All rights reserved. 1

1.1 Tivoli Storage Productivity Center for Replication overview
IBM Tivoli Storage Productivity Center for Replication is a component of IBM Tivoli Storage
Productivity Center and IBM SmartCloud® Virtual Storage Center that manages copy
services in storage environments. Copy services are features that are used by storage
systems to configure, manage, and monitor data replication functions. These copy services
include IBM FlashCopy, Metro Mirror, Global Mirror, and Metro Global Mirror data replication.

Tivoli Storage Productivity Center for Replication manages copy services for the following
storage systems:
򐂰 IBM System Storage D6000
򐂰 IBM System Storage DS8000
򐂰 IBM TotalStorage Enterprise Storage Server® Model 800
򐂰 IBM SAN Volume Controller
򐂰 IBM Storwize V3500
򐂰 IBM Storwize V3700
򐂰 IBM Storwize V7000
򐂰 IBM Storwize V7000 Unified
򐂰 IBM XIV System Storage

Tivoli Storage Productivity Center for Replication automates key replication management
tasks to help you improve the efficiency of your storage replication. You can use a simple GUI
to configure, automate, manage, and monitor all key data replication tasks in your
environment, including the following tasks:
򐂰 Manage and monitor multi-site environments to meet disaster recovery requirements
򐂰 Automate the administration and configuration of data replication features
򐂰 Keep data on multiple related volumes consistent across storage systems in a planned or
unplanned outage
򐂰 Recover to a remote site to reduce downtime of critical applications
򐂰 Provide high availability for applications by using IBM HyperSwap® technology
򐂰 Practice recovery processes while disaster recovery capabilities are maintained

Figure 1-1 on page 3 shows the Tivoli Storage Productivity Center for Replication
environment.

2 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 1-1 Tivoli Storage Productivity Center for Replication environment

1.2 Terminology
In this section, we describe the following key terms to help you understand and effectively use
Tivoli Storage Productivity Center for Replication:
򐂰 Management server
The management server is a system that has Tivoli Storage Productivity Center for
Replication installed. The management server provides a central point of control for
managing data replication.
You can create a high availability environment by setting up a standby management
server. A standby management server is a second instance of Tivoli Storage Productivity
Center for Replication that runs on a different physical system, but is continuously
synchronized with the primary (or active) Tivoli Storage Productivity Center for Replication
server.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 3

 The active management server issues commands and processes events, while the
standby management server records the changes to the active server. As a result, the
standby management server contains identical data to the active management server and
can take over and run the environment without any loss of data.
򐂰 Storage system
A storage system is a hardware device that contains data storage. Tivoli Storage
Productivity Center for Replication can control data replication within and between various
storage systems.
To replicate data among storage systems by using Tivoli Storage Productivity Center for
Replication, you must manually add a connection to each storage system.
򐂰 Host system
A host system is an AIX® or IBM z/OS system that connects to storage systems to enable
certain replication features for those systems.
A connection to a z/OS host system is required if you want to enable z/OS features, such
as HyperSwap and hardened freeze in Tivoli Storage Productivity Center for Replication
sessions.
A connection to an AIX host system is required if you want to use the Open HyperSwap
feature. This feature enables the automatic swap of input/output (I/O) to the volumes on a
secondary site when a failure occurs when I/O iswritten to the primary site.
򐂰 Users and groups
Tivoli Storage Productivity Center for Replication does not maintain a directory of user
names and passwords. Instead, the application uses the operating system repository that
is created during the installation of Tivoli Storage Productivity Center or a Lightweight
Directory Access Protocol (LDAP) repository for user authentication.
You can use the Tivoli Storage Productivity Center for Replication graphical user interface
(GUI) or command-line interface (CLI) to assign the users and groups that are defined in
the user repository to a user role.
򐂰 User roles
A user role determines the tasks and sessions that a user or group can manage. There
are three roles that are defined in Tivoli Storage Productivity Center for Replication:
Administrator, Operator, and Monitor.
Administrators have unrestricted access to all features and functions in Tivoli Storage
Productivity Center for Replication.
Operators can manage specific sessions.
Monitors can view information in the Tivoli Storage Productivity Center for Replication;
however, they cannot modify or perform any commands or actions.
򐂰 Global Copy
For ESS800, DS6000™, and DS8000 storage systems, Global Copy is an asynchronous
long-distance copy option for data migration and backup.
򐂰 Session
A session completes a specific type of data replication for a specific set of volumes. During
data replication, data is copied from a source volume to one or more target volumes,
depending on the session type. The source volume and target volumes that contain copies
of the same data are collectively referred to as a copy set. A session can contain one or
more copy sets. The type of data replication that is associated with the session determines
the actions that you can perform against all copy sets in the session, the number of
volumes that a copy set can contain, and the role that each volume plays.

4 Tivoli Storage Productivity Center for Replication for Open Systems

򐂰 Copy set
A copy set is a set of volumes that represent copies of the same data. During data
replication, data is copied from a source volume to one or more target volumes, depending
on the session type. The source volume and target volumes that contain copies of the
same data are collectively referred to as a copy set.
Each volume in a copy set must be of the same size and volume type. For example, SAN
Volume Controller volumes must be used with other SAN Volume Controller volumes. The
number of volumes in the copy set and the role that each volume plays is determined by
the session type that is associated with the session to which the copy set belongs.
򐂰 Volume roles
Volume roles are given to every volume in the copy set.
The volume role types are host volume, journal volume, intermediate volume, target
volume, and change volume (SAN Volume Controller or Storwize storage systems only).
The role defines how the volume is used in the copy set and the site location of the
volume. For example, a host volume at the primary site has the role of Host1, while a
journal volume at the secondary site has the role of Journal2.
򐂰 Role pair
A role pair is the association of two roles in a session that take part in a copy relationship.
For example, in a Metro Mirror session, the role pair can be the association between the
volume roles of Host1 and Host2.
򐂰 Site
The site determines the location of the volumes. The number of sites in a copy set is
determined by the session type. Tivoli Storage Productivity Center for Replication
supports up to the following three sites:
– Site 1: The location of the primary storage system that contains the source data. Upon
initial configuration, this site contains the host volumes with updates that are copied to
the target volumes.
– Site 2: The location of the secondary storage system that receives the copy updates
from the primary storage system.
– Site 3: The location of the tertiary storage system that receives the copy updates from
the secondary storage system.
򐂰 Host volume
A host volume is a volume that is connected to a server that reads and writes input/output
(I/O). A host volume can be the source of updated tracks when the server that is
connected to the host volume is actively issuing read and write I/O. A host volume can
also be the target of the replication. When the host volume is the target, writes are
inhibited.
Host volumes are abbreviated as Hx, where x identifies the site.
򐂰 Journal volume
A journal volume stores data that changed since the last consistent copy was created.
This volume functions like a journal and holds the required data to reconstruct consistent
data at the Global Mirror remote site. When a session must be recovered at the remote
site, the journal volume is used to restore data to the last consistency point. A FlashCopy
replication session can be created between the host or intermediate volume and the
corresponding journal volume after a recover request is started to create another
consistent version of the data.
Journal volumes are abbreviated as Jx, where x identifies the site.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 5

 򐂰 Intermediate volume
An intermediate volume receives data from the primary host volume during a replication
with practice session. During a practice, data on the intermediate volumes is flash copied
to the practice host volumes.
Depending on the replication method that is used, data on intermediate volumes might not
be consistent.
Intermediate volumes are abbreviated as Ix, where x identifies the site.
򐂰 Target volume
A target volume receives data from a host or intermediate volume. Depending on the
replication type, that data might or might not be consistent. A target volume can also
function as a source volume. For example, a common use of the target volume is as a
source volume to allow practicing for a disaster, such as data mining at the recovery site
while still maintaining disaster recovery capability at the production site.
򐂰 Change volume
A change volume contains point-in-time images that are copied from the host or target
volume.
Change volumes are abbreviated as Cx, where x identifies the site.

Figure 1-2 shows how the preceding session-related terms relate to each other.

Note: In Figure 1-2, the following terms are abbreviated; Fibre Channel (FC), Metro Mirror
(MM), Global Mirror (GM), and Metro Global Mirror (MGM).

Figure 1-2 Tivoli Storage Productivity Center for Replication session-related terminology

6 Tivoli Storage Productivity Center for Replication for Open Systems

1.3 Architecture
Tivoli Storage Productivity Center and SmartCloud Virtual Storage Center offer storage
infrastructure management that helps optimize storage management by centralizing,
simplifying, automating, and optimizing storage tasks that are associated with storage
systems, storage networks, copy services management, capacity, and reporting
management.

Tivoli Storage Productivity Center for Replication is a component of Tivoli Storage

Productivity Center and SmartCloud Virtual Storage Center, which provides copy services
management of different IBM storage systems.

Tivoli Storage Productivity Center for System z® is a separate product that offers all of the
functions that are provided by the Tivoli Storage Productivity Center for Replication product.
The difference is that it is packaged to run only on System z and it uses a mixture of FICON®
and TCP/IP communications to provide copy services management of different IBM Storage
Systems. For more information about Tivoli Storage Productivity Center for System z, see the
IBM Redbooks publication IBM Tivoli Storage Productivity Center for Replication for Series z,
SG24-7563.

Figure 1-3 shows a Tivoli Storage Productivity Center overview and the key components that
provide simplified administration of your storage environment.
I

Figure 1-3 Tivoli Storage Productivity Center overview

Detailed architecture of Tivoli Storage Productivity Center components is shown in Figure 1-4
on page 8. In this figure, you can see Tivoli Storage Productivity Center for Replication
components and how are they related.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 7

 Figure 1-4 Tivoli Storage Productivity Center components

The Tivoli Storage Productivity Center features the following components:

򐂰 GUI
The following GUIs are available:
– Tivoli Storage Productivity Center provides two GUIs for managing the storage
infrastructure in an enterprise environment: the stand-alone GUI and the web-based
GUI. Each GUI provides different functions for working with monitored resources. For
more information about each Tivoli Storage Productivity Center GUI, see the draft of
the Tivoli Storage Productivity Center V5.2 Release Guide, SG24-8204.
– Tivoli Storage Productivity Center for Replication provides a GUI that is used to
manage all Tivoli Storage Productivity Center for Replication functions. These
functions include administration and configuration of the copy services, and managing
and monitoring the status of copy services. For more information about the Tivoli
Storage Productivity Center for Replication GUI, see Chapter 3, “General
administration and high availability” on page 61.
– Tivoli Common Reporting provides the reporting service for Tivoli Storage Productivity
Center reports. Tivoli Common Reporting includes Cognos® reporting software.
򐂰 CLI
The CLI is used to issue commands for key Tivoli Storage Productivity Center and Tivoli
Storage Productivity Center for Replication functions. It is also used to enable scripts for
automating functions.

8 Tivoli Storage Productivity Center for Replication for Open Systems

򐂰 Data server
The Data server is a Tivoli Storage Productivity Center component that is the control point
for product scheduling functions, configuration, event information, reporting, and GUI
support. It coordinates communication with and data collection from agents that scan file
systems and databases to gather storage demographics and populate the database with
results. Automated actions can be defined to perform file system extension, data deletion,
and Tivoli Storage Productivity Center backup or archiving, or event reporting when
defined thresholds are encountered. The Data server is the primary contact point for GUI
functions. It also includes functions that schedule data collection and discovery for the
Device server.
򐂰 Device server
The Device server is a Tivoli Storage Productivity Center component that discovers,
gathers information from, analyzes performance of, and controls storage systems and
SAN fabrics. It coordinates communication with and data collection from agents that scan
SAN fabrics and storage devices.
򐂰 Jazz™ for Service Management
Jazz for Service Management is used by Tivoli Common Reporting to provide the
reporting service for Tivoli Storage Productivity Center reports.
򐂰 Replication server
The Replication server is a Tivoli Storage Productivity for Replication component that
coordinates communication and processes tasks that are related to copy services and
replication.
򐂰 Database
Tivoli Storage Productivity uses a DB2® single database instance that serves as the
repository for all Tivoli Storage Productivity Center components.
Tivoli Storage Productivity for Replication uses an embedded database, which is created
automatically during Tivoli Storage Productivity Center installation.

High availability architecture

The recommended architecture of the Tivoli Storage Productivity for Replication environment
is based on a high availability configuration where the primary Tivoli Storage Productivity
Center for Replication management server is installed in the primary site and the standby
Tivoli Storage Productivity Center for Replication management server is installed in the
disaster recovery site. Synchronization is established between the primary and standby
management server. If a failure of the primary management server occurs, the standby
management server takes over and continues the replication management.

Typical high availability architecture of the Tivoli Storage Productivity for Replication solution
is shown in Figure 1-5 on page 10.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 9

Figure 1-5 Tivoli Storage Productivity Center for Replication high availability architecture

1.4 Copy services overview

This section describes the FlashCopy, Metro Mirror, Global Mirror, and Metro Global Mirror
copy services. Copy Services include a set of disaster recovery, data migration, and data
duplication functions that protect your data.

The copy service determines whether you can replicate data within a single site or replicate to
a second or third site. The copy service that you should use depends on your data replication
requirements and your environment.

FlashCopy
FlashCopy replication creates a point-in-time copy in which the target volume contains the
same data as the source volume at the point in time when the copy was established. Any
subsequent write operations to the source volume are not reflected on the target volume.

With FlashCopy replication, the source volume is in one logical subsystem (LSS) or I/O group
(depending on the storage system type) and the target volume is in the same or another LSS
or I/O group.

FlashCopy replication occurs on a single site.

10 Tivoli Storage Productivity Center for Replication for Open Systems

 Metro Mirror
Metro Mirror is a form of synchronous remote replication that operates between two sites that
are within 300 km of each other. Synchronous mirroring means that a target volume on the
remote site is constantly updated to match changes that are made to a source volume on the
local site. Because the data is the same on the source and target volumes, no data is lost if
you must use data from the target site for recovery.

Global Mirror
Global Mirror is a form of asynchronous remote replication that operates between two sites
that are over 300 km from each other. Asynchronous mirroring means that a target volume on
the remote site is updated a few seconds after the changes are made to a source volume on
the local site.

With Global Mirror, the distance between sites is limited only by your network capabilities and
channel extension technology. The unlimited distance enables you to better choose your
remote site location that is based on business needs and enables greater site separation to
add protection from local disasters.

Metro Global Mirror

Metro Global Mirror combines the capabilities of Metro Mirror and Global Mirror for greater
protection against planned and unplanned outages.

Metro Global Mirror is a three-site, high availability disaster recovery solution. Metro Global
Mirror uses synchronous replication to mirror data between a local site and an intermediate
site, and asynchronous replication to mirror data from an intermediate site to a remote site.

By using the two-site synchronous replication, you can recover data in the event of a local
disaster, while the longer distance asynchronous copy to a third site protects data in the event
of larger scale regional disasters.

Snapshot
Snapshot sessions create a point-in-time copy of a volume or set of volumes on the same site
(Site 1) without having to define a specific target volume. The target volumes of a Snapshot
session are automatically created when the snapshot is created.

Note: Snapshot sessions are available only for IBM XIV Storage System.

1.5 Session types and usage

A session is used to complete a specific type of data replication against a specific set of
volumes. The type of copy service that is associated with the session determines the
replication actions that are available for the session. For example, the options for FlashCopy
sessions are different from the options for Metro Mirror sessions.

Table 1-1 on page 12 shows the session types that are available in Tivoli Storage Productivity
Center for Replication and the storage systems that are supported. The Multidirectional
column indicates whether you can copy data in multiple directions.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 11

 Table 1-1 Session types and supported storage systems
Session type Number of supported sites Supported storage systems

FlashCopy 1 All, except IBM XIV Storage

System

Snapshot 1 IBM XIV Storage System

Metro Mirror Single Direction 2 (data replication is only one All, except IBM XIV Storage
direction) System

Metro Mirror Failover/Failback 2 (data replication can be All

bidirectional)

Metro Mirror Failover/Failback 2 (data replication can be All, except IBM XIV Storage
with Practice bidirectional) System

Global Mirror Single Direction 2 (data replication is only one All, except IBM XIV Storage
direction) System

Global Mirror Failover/Failback 2 (data replication can be All

bidirectional)

Global Mirror Failover/Failback 2 (data replication can be SAN Volume Controller,

with Change Volumes bidirectional) Storwize V3500, Storwize
V3700, Storwize V7000, and
Storwize V7000 Unified

Global Mirror Failover/ Failback 2 (data replication can be All, except IBM XIV Storage
with Practice bidirectional) System

Global Mirror Either Direction 2 (data replication can be ESS, DS6000, and DS8000
with Two Site Practice bidirectional)

Metro Global Mirror 3 (data replication can be ESS and DS8000

multidirectional)

Metro Global Mirror with 3 (data replication can be ESS and DS8000
Practice multidirectional)

For session types that support multiple sites and are not single direction only, you can start
data replication in multiple directions for recovery purposes. For example, you can start data
replication from the target volume to the source volume for a bidirectional session type.

1.5.1 Practice sessions

By using practice sessions, you can test disaster-recovery actions while maintaining
disaster-recovery capability.

Practice sessions include intermediate volumes on the remote site that contains the target
volumes. A FlashCopy operation is completed from the intermediate volumes to the target
volumes. The target volumes contain point-in-time data that you can use to test data-recovery
actions. For example, you can run scripts that attach your host systems to the target volumes
on the remote site or complete an initial program load (IPL) on the site.

Because data replication continues from the source volume to the intermediate volume in a
normal manner, your data is recoverable while you are testing the practice volume.
To use practice volumes, the session must be in the Prepared state.

12 Tivoli Storage Productivity Center for Replication for Open Systems

 Note: When practice sessions are used, Tivoli Storage Productivity Center for Replications
assumes that the set of volumes that are used for practicing is also used in case of actual
recovery. For this reason, the Tivoli Storage Productivity Center for Replication operations
and storage resources that are used for practicing are the same in the case of a real
recovery or site switch. This approach relieves the unpredictably of untested procedures
during the real recovery operations.

Note: You can test disaster-recovery actions without the use of practice volumes. However,
if you do not use practice volumes, data replication between sites is interrupted while you
are recovering data to the remote site.

1.5.2 Data copying symbols

The following sections include symbols that represent the type of copying that is occurring
between volumes. The symbols are shown in Table 1-2.

Table 1-2 Copy type symbols

Type of copy Symbol

FlashCopy

Synchronous

Asynchronous

1.5.3 FlashCopy sessions

FlashCopy sessions copy the data that is on the source volume to the target volume on the
same site (Site 1). The target volume contains the same data as the source volume at the
point in time when the copy was established. Any subsequent write operations to the source
volume are not reflected on the target volume.

Figure 1-6 shows the volumes and data flow for the session.

Figure 1-6 FlashCopy session

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 13

1.5.4 Snapshot sessions

Note: Snapshot sessions are available only for IBM XIV Storage System.

Snapshot sessions create a point-in-time copy of a volume or set of volumes on the same site
(Site 1) without having to define a specific target volume. The target volumes of a Snapshot
session are automatically created when the snapshot is created.

Figure 1-7 shows the volumes for the session.

Figure 1-7 Snapshot session

1.5.5 Metro Mirror Single Direction sessions

Metro Mirror Single Direction sessions copy data in a single direction from the source volume
on the local site (Site 1) to the target volume on the remote site (Site 2).

Figure 1-8 shows the volumes and data flow for the session.

Figure 1-8 Metro Mirror Single Direction session

1.5.6 Metro Mirror Failover/Failback sessions

Metro Mirror Failover/Failback sessions provide the same capabilities as Metro Mirror Single
Directions sessions. The difference is that data replication for Metro Mirror Failover/Failback
sessions is bidirectional.

Figure 1-9 shows the volumes and data flow for the session when data is copied from Site 1
to Site 2.

Figure 1-9 Metro Mirror Failover/Failback session

1.5.7 Metro Mirror Failover/Failback with Practice sessions

Metro Mirror Failover/Failback with Practice sessions combine Metro Mirror and FlashCopy
replication to provide a point-in-time copy of the data on the remote site.

14 Tivoli Storage Productivity Center for Replication for Open Systems

 For this session type, a synchronous copy occurs from a source volume on the local site (Site
1) to an intermediate volume on the remote site (Site 2). A FlashCopy then occurs from the
intermediate volume to a target volume on the remote site.

Figure 1-10 shows the volumes and data flow for the session when data is copied from Site 1
to Site 2.

Figure 1-10 Metro Mirror Failover/Failback with Practice session

1.5.8 Global Mirror Single Direction sessions

Global Mirror Single Direction sessions copy data in a single direction from a source volume
on the local site (Site 1) to a target volume on the remote site (Site 2).

ESS800, DS6000, and DS8000 storage systems

For ESS800, DS6000, and DS8000 storage systems, an asynchronous copy occurs from the
source volume to the target volume. A FlashCopy then occurs from the target volume to a
journal volume on the remote site.

Figure 1-11 shows the volumes and data flow for an ESS, DS6000, or DS8000 Global Mirror
Single Direction session when data is copied from Site 1 to Site 2.

Figure 1-11 Global Mirror Single Direction session for ESS800, DS6000, and DS8000 storage systems

All other storage systems

For all other storage system sessions, the data flow is the same. However, there is no
FlashCopy to a journal volume.

1.5.9 Global Mirror Failover/Failback

Global Mirror Failover/Failback sessions provide the same capabilities as Global Mirror Single
Direction sessions. The difference is that data replication for Global Mirror Failover/Failback
sessions is bidirectional.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 15

 ESS800, DS6000, and DS8000 storage systems
Figure 1-12 represents the volumes and data flow for an ESS, DS6000, or DS8000 Global
Mirror Failover/Failback session when data is copied from Site 1 to Site 2.

Figure 1-12 Global Mirror Failover/Failback session for ESS800, DS6000, and DS8000 storage
systems

All other storage systems

For all other storage system sessions, the data flow is the same. However, there is no
FlashCopy to a journal volume.

1.5.10 Global Mirror Failover/Failback with Change Volumes sessions

Global Mirror Failover/Failback with Change Volumes sessions provide the same capabilities
as Global Mirror Failover/Failback sessions. The difference is that Global Mirror
Failover/Failback with Change Volumes sessions also provides the option of enabling or
disabling the use of change volumes.

Note: Snapshot sessions are available only for SAN Volume Controller and Storwize
storage systems.

Figure 1-13 shows the volumes and data flow for the session when data is copied from Site 1
to Site 2.

Figure 1-13 Global Mirror Failover/Failback with Change Volumes session

1.5.11 Global Mirror Failover/Failback with Practice sessions

Global Mirror Failover/Failback with Practice sessions combine Global Mirror and FlashCopy
replication to provide a point-in-time copy of the data on the remote site (Site 2).

ESS800, DS6000, and DS8000 storage systems

For ESS800, DS6000, and DS8000 storage systems, an asynchronous copy occurs from the
source volume on the local site (Site 1) to the intermediate volume on the remote site (Site 2).
A FlashCopy then occurs from the intermediate volume to the target volume and the journal
volume on the remote site.

16 Tivoli Storage Productivity Center for Replication for Open Systems

 Figure 1-14 represents the volumes and data flow for an ESS, DS6000, or DS8000 Global
Mirror Failover/Failback with Practice session when data is copied from Site 1 to Site 2.

Figure 1-14 Global Mirror Failover/Failback with Practice session for ESS800, DS6000, and DS8000

All other storage systems

For all other storage system sessions, the data flow is the same. However, there is no
FlashCopy to a journal volume.

1.5.12 Global Mirror Either Direction with Two-Site Practice sessions

Global Mirror Either Direction with Two-Site Practice sessions combine Global Mirror and
FlashCopy replication to provide a point-in-time copy of the data on the local (Site 1) and
remote site (Site 2). This session type includes intermediate and journal volumes on the local
and remote site so that you can practice disaster recovery from either site.

Figure 1-15 shows the volumes and data flow for the session when data is copied from Site 1
to Site 2.

Figure 1-15 Global Mirror Either Direction with Two Site Practice session

1.5.13 Metro Global Mirror sessions

Note: Metro Global Mirror sessions are available only for ESS800 and DS8000 storage
systems.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 17

 Metro Global Mirror sessions combine Metro Mirror, Global Mirror, and FlashCopy replication
into a single session. Metro Global Mirror sessions support three sites that are varying
distances apart.

For this session type, a synchronous copy occurs from the source volume on the local site
(Site 1) to the target volume on the second site (Site 2). An asynchronous copy then occurs
from the second site to the target volume on the third site (Site 3) and a FlashCopy occurs
from the target to the journal volume on Site 3.

Figure 1-16 shows the volumes and data flow for the session when data is copied from Site 1
to Site 3.

Figure 1-16 Metro Global Mirror session

1.5.14 Metro Global Mirror with Practice sessions

Note: Metro Global Mirror with Practice sessions are available only for ESS800 and
DS8000 storage systems.

Metro Global Mirror with Practice sessions combine Metro Mirror, Global Mirror, and
FlashCopy replication across three sites to provide a point-in-time copy of the data on the
third site.

For this session type, a synchronous copy occurs from the source volume on the local site
(Site 1) to the target volume on the second site (Site 2). An asynchronous copy then occurs
from the second site to the intermediate volume on the third site (Site 3). A FlashCopy occurs
from the intermediate volume to the target and journal volumes on Site 3.

Figure 1-17 on page 19 shows the volumes and data flow for the session when data is copied
from Site 1 to Site 3.

18 Tivoli Storage Productivity Center for Replication for Open Systems

 Figure 1-17 Metro Global Mirror with Practice session

1.5.15 Session states

Sessions can exist in different states. The following sections describe the states for
FlashCopy sessions and remote copy sessions.

FlashCopy session states

Table 1-3 shows the states for FlashCopy sessions.

Table 1-3 FlashCopy session states

Session state Description Storage systems

Defined The session exists, but is not All

started and is not managing
any relationships on the
hardware.

Preparing The volumes in the session are SAN Volume Controller,

initializing, synchronizing, or Storwize V3500, Storwize
resynchronizing. V3700, Storwize V7000, and
Storwize V7000 Unified storage
systems

Prepared All volumes in the session are SAN Volume Controller,

initialized. Storwize V3500, Storwize
V3700, Storwize V7000, and
Storwize V7000 Unified storage
systems

Suspended Replication is stopped on all All

role pairs. Another recoverable
flag indicates whether data is
consistent and recoverable.

Target Available The target volumes are All

write-enabled. Another
recoverable flag indicates
whether data is consistent and
recoverable.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 19

 Session state Description Storage systems

Terminating The session is terminating All

because a Terminate command
was issued under the following
conditions:
򐂰 The target volume is
permitted to be Metro
Mirror or Global Copy.
򐂰 The Require or Attempt to
Preserve Mirror option is
set.

Figure 1-18 shows the relationship of these states. If an error occurs when the Start or Flash
command is issued, the session state becomes Suspended.

Not Defined

Create Session Delete Session

Defined
flash

start

Preparing Preparing terminate terminate

flash start

Prepared Prepared

flash
start

Target Available

Figure 1-18 FlashCopy session states

Remote copy session states

Table 1-4 shows the states for remote copy sessions (Metro Mirror, Global Mirror, and Metro
Global Mirror).

Table 1-4 Remote copy session states

Session state Description Session types

Defined The session exists, but is not All

started and is not managing
any relationships on the
hardware.

Flashing The session is creating the All sessions with practice

practice FlashCopy.

20 Tivoli Storage Productivity Center for Replication for Open Systems

Session state Description Session types

Preparing The volumes in the session are All (excluding sessions for IBM
initializing, synchronizing, or XIV Storage System)
resynchronizing.

Prepared All volumes in the session are All (excluding sessions for IBM
initialized. The session is XIV Storage System)
consistent and is actively
copying data.

Recovering The session is recovering. Global Mirror and Metro Global

Mirror

Suspending The session is in a transitory Global Mirror and Metro Global

state that is caused by the Mirror (only for ESS800,
Suspend command or DS6000, and DS8000 storage
suspending event. Copy systems)
operations are suspended.

Suspended Replication is stopped on all Metro Mirror, Global Mirror, and

role pairs. Another recoverable Metro Global Mirror
flag indicates whether data is
consistent and recoverable.

SuspendedH1H2 MGM Data copying between site 1 Metro Global Mirror

and site 2 is stopped for the
session.

SuspendedH1H3 MGM Data copying between site 1 Metro Global Mirror

and site 3 is stopped for the
session.

Target Available The target volumes are All

write-enabled. Another
recoverable flag indicates
whether data is consistent and
recoverable.

Terminating The session is terminating All

because a Terminate command
was issued under the following
conditions:
򐂰 The target volume is
permitted to be Metro
Mirror or Global Copy.
򐂰 The Require or Attempt to
Preserve Mirror option is
set.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 21

 Figure 1-19 shows the relationship of these states for sessions that do not include practice
volumes.

Not Defined

Create Session Delete Session

Defined
terminate
start

Preparing

Event suspend/pause
Add Copy Set

Prepared
Event suspend/pause

Suspending

start
Suspended terminate
recover

Recovering

start terminate
Target Available

Figure 1-19 Remote copy session states

1.5.16 Session commands

The commands that are available for a session depend on the session type.

Commands are issued synchronously to Tivoli Storage Productivity Center for Replication
sessions. Any subsequent command that is issued to an individual session is not processed
until the first command completes.

Some commands, such as the Start command, can take an extended amount of time to
complete. By using the GUI, you can still issue commands to other sessions and not hold up
functionality. When a command completes, the GUI console displays the results of the
command.

The tables in the following sections show the commands that are available by session type.
These commands represent the GUI and not the CLI command, which might require specific
syntax to be valid.

22 Tivoli Storage Productivity Center for Replication for Open Systems

FlashCopy Commands
Table 1-5 shows the commands for FlashCopy sessions.

Table 1-5 FlashCopy commands

Command Meaning

Start Places the session in the Prepared state. This command is available
only for sessions for SAN Volume Controller, Storwize V3500, Storwize
V3700, Storwize V7000, and Storwize V7000 Unified storage systems.

Flash Completes the FlashCopy operation.

Initiate Background Copy Copies all tracks from the source to the target immediately instead of
waiting until the source track is written to. This command is valid only
when the background copy is not running.

Terminate Removes all active physical copies and relationships from the hardware
during an active session.

If you want the targets to be data consistent before you remove their
relationship, you must issue the Initiate Background Copy command if
NOCOPY was specified, and then wait for the background copy to
complete by checking the copying status of the pairs.

Snapshot commands
Table 1-6 shows the commands for Snapshot sessions.

Note: Snapshot sessions are available only for IBM XIV Storage System.

Table 1-6 Snapshot commands

Command Meaning

Create Snapshot Creates a snapshot of the volumes in the session.

Restore Restores the H1 volumes in the session from a set of snapshot volumes.
You must have at least one snapshot group to restore from. When you
issue this command in the Tivoli Storage Productivity Center for
Replication GUI, you are prompted to select the snapshot group.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 23

 Table 1-7 shows the commands for Snapshot groups. A snapshot group is a grouping of
snapshots of individual volumes in a consistency group at a specific point in time.

Table 1-7 Snapshot group commands

Command Meaning

Delete Deletes the snapshot group and all the individual snapshots that are in
the group from the session and from IBM XIV Storage System. If the
deleted snapshot group is the last snapshot group that is associated
with the session, the session returns to the Defined state.

Disband Disbands the snapshot group. When a snapshot group is disbanded, the
snapshot group no longer exists. All snapshots in the snapshot group
become individual snapshots that are no longer associated to the
consistency group or the session. After a snapshot group is disbanded,
it is no longer displayed in or managed by Tivoli Storage Productivity
Center for Replication. If the disbanded snapshot group is the last
snapshot group that is associated with the session, the session returns
to the Defined state.

Duplicate Duplicates the snapshot group. When a snapshot group is duplicated, a

snapshot group is created with new snapshots for all volumes that are
in the duplicated group. The name of the duplicated snapshot group is
generated automatically by IBM XIV Storage System.

Lock Locks a snapshot group. If the snapshot group is locked, write

operations to the snapshots that are in the snapshot group are
prevented. By default, a snapshot group is locked when it is created.
This action is valid only if the snapshot group is unlocked.

Overwrite Overwrites the snapshot group to reflect the data that is on the H1
volume.

Rename Renames the snapshot group to a name that you provide. The name can
be a maximum of 64 alphanumeric characters.

Restore Restores the contents of a snapshot group by using another snapshot

group in the session. Both of the snapshot groups must contain the
same subset of volumes.

Set Priority Sets the priority in which a snapshot group is deleted. The value can be
the number 1 - 4. A value of 1 specifies that the snapshot group is
deleted last. A value of 4 specifies that the snapshot group is deleted
first.

Unlock Unlocks a snapshot group. If the snapshot group is unlocked, write

operations to the snapshots that are in the snapshot group are enabled
and the snapshot group is displayed as modified. This action is valid only
if the snapshot group is locked.

24 Tivoli Storage Productivity Center for Replication for Open Systems

Metro Mirror commands
Table 1-8 shows the commands for Metro Mirror sessions. The applicable commands depend
on the Metro Mirror session type and the storage system.

Table 1-8 Metro Mirror commands

Command Meaning

Enable Copy to Site 1 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the H2 → H1 command becomes available.

Enable Copy to Site 2 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the Start H1 → H2 command becomes
available.

Flash Creates a FlashCopy image from I2 volumes to H2 volumes. The

amount of time for this to occur varies depending on the number of copy
sets in the session.

HyperSwap Triggers a HyperSwap where I/O is redirected from the source volume
to the target volume without affecting the application that is using those
volumes.

Recover Completes the steps necessary to make the target available as the new
primary site. Upon completion of this command, the session becomes
Target Available.

Start Establishes a single-direction session with the hardware and begins the
synchronization process between the source and target volumes.

Start H1 → H2 Applies only to failover/failback sessions. Indicates the direction

between two hosts in a Metro Mirror failover/fallback session.

Start H2 → H1 Indicates direction of a failover/failback between two hosts in a Metro

Mirror session. If the session was recovered with the failover/failback
function such that the production site is now H2, you can issue the Start
H2 → H1 command to start production on H2 and provide protection.

StartGC Establishes Global Copy relationships between the H1 volumes and the
H2 volumes, and begins asynchronous data replication from H1 to H2.
While in the Preparing state, it does not change to the Prepared state
unless you switch to Metro Mirror.

Stop Suspends updates to all the targets of pairs in a session. This command
can be issued at any point during an active session. However, updates
are not considered to be consistent.

Suspend Causes all target volumes to remain at a data-consistent point and stops
all data that is moving to the target volumes. This command can be
issued at any point during a session when the data is actively copied.

Terminate Removes all physical copies from the hardware during an active
session. If you want the targets to be data consistent before you remove
their relationship, you must issue the Suspend command, the Recover
command, and then the Terminate command.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 25

 Global Mirror commands
Table 1-9 shows the commands for Global Mirror sessions. The applicable commands
depend on the Global Mirror session type and the storage system.

Table 1-9 Global Mirror commands

Command Meaning

Enable Copy to Site 1 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the H2 → H1 command becomes available.

Enable Copy to Site 2 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the Start H1 → H2 command becomes
available

Flash Ensures that all I2s are consistent, and then flashes the data from I2 to
the H2 volumes. After the flash is complete, the Global Mirror session is
automatically restarted, and the session begins forming consistency
groups on I2. You can then use the H2 volumes to practice your disaster
recovery procedures.

Recover Completes the steps necessary to make the target available as the new
primary site. Upon completion of this command, the session becomes
Target Available.

Start Sets up all relationships in a single-direction session and begins the

process that is necessary to start forming consistency groups on the
hardware.

Start H1 → H2 Indicates direction between two hosts in a Global Mirror failover/fallback

session. This command can be issued at any point during a session
when the data is actively copied.

Start H2 → H1 Indicates direction of a failover/failback session. If a recover was

performed on a session such that the production site is now H2, you can
issue Start H2 → H1 to start moving data back to Site 1. However, this
start does not provide consistent protection as it copies only
asynchronously back because of the long distance. An extended
distance (XD) relationship is used. When you are ready to move
production back to Site 1, issue a suspend to the session. This puts the
relationships into a synchronized state and suspends them consistently.

StartGC H1 → H2 Establishes Global Copy relationships between site 1 and site 2 and
begins asynchronous data replication from H1 to H2. To change the
session state from Preparing to Prepared, you must issue the Start
H1 → H2 command and the session must begin to form consistency
groups.

Suspend Stops all consistency group information when the data is actively copied.
This command can be issued at any point during a session when the
data is actively copied.

Terminate Removes all physical copies from the hardware. This command can be
issued at any point in an active session. If you want the targets to be
data consistent before you remove their relationship, you must issue the
Suspend command, the Recover command, and then the Terminate
command.

26 Tivoli Storage Productivity Center for Replication for Open Systems

Metro Global Mirror commands
Table 1-10 shows the commands for Metro Global Mirror sessions. The applicable commands
depend on the Metro Global Mirror session type and the storage system.

Table 1-10 Metro Global Mirror commands

Command Meaning

Enable Copy to Site 1 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the Start H2 → H1 → H3 command becomes
available.

Enable Copy to Site 2 Confirms that you want to reverse the direction of replication before you
reverse the direction of copying in a failover and failback session. After
you issue this command, the Start H1 → H2 → H3 command becomes
available.

HyperSwap Triggers a HyperSwap where I/O is redirected from the source volume
to the target volume, without affecting the application that uses those
volumes.

Flash Ensures that all I3s are consistent, and then flashes the data from I3 to
the H3 volumes.
This command is available in the following states:
򐂰 Target Available state when the active host is H3.
Use this command if the FlashCopy portion of the Recover
command from I3 to H3 fails for any reason. The problem can be
addressed, and a Flash command can be issued to complete the
flash of the consistent data from I3 to H3.
򐂰 Prepared state when the active host is H1 and data is copying H1 to
H2 to I3, or the active host is H2 and data is copying H2 to H1 to
H3.
򐂰 Prepared state when the active host is H2 and data is copying H2 to
I3.
򐂰 Prepared state when the active host is H1 and data is copying H1 to
I3.

Recover H1 Specifying H1 makes the H1 volume Target Available. Metro Global

Mirror (when H2 → H1 → H3 is run) can move production to the H1 or
H3 set of volumes. Tivoli Storage Productivity Center for Replication
processing is different, depending on the recovery site. Therefore, the
site designation is added to the recover command so Tivoli Storage
Productivity Center for Replication can set up for the failback.

Recover H2 Specifying H2 makes the H2 volume Target Available. Metro Global

Mirror (when H1 → H2 → H3 is run) can move production to the H2 or
H3 set of volumes. Tivoli Storage Productivity Center for Replication
processing is different, depending on the recovery site. Therefore, the
site designation is added to the recover command so Tivoli Storage
Productivity Center for Replication can set up for the failback.

Recover H3 Specifying H3 makes the H3 volume Target Available. Metro Global

Mirror (when H1 → H2 → H3 is run) can then move production to the H3
set of volumes. Because Tivoli Storage Productivity Center for
Replication processing is different depending on the recovery site, the
site designation is added to the recover command so that Tivoli Storage
Productivity Center for Replication can set up for the failback.

This command sets up H3 so that you can start the application on H3.
H3 becomes the active host, and you then can start H3 → H1 → H2 to
perform a Global Copy copy back.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 27

 Command Meaning

Re-enable Copy to Site 1 After you issue a Recover H1 command, you can run this command to
restart the copy to the original the direction of replication in a failover and
failback session.

Re-enable Copy to Site 2 After you issue a Recover H2 command, you can run this command to
restart the copy to the original the direction of replication in a failover and
failback session.

Re-enable Copy to Site 3 After you issue a Recover H3 command, you can run this command to
restart the copy to the original the direction of replication in a failover and
failback session.

Start H1 → H2 → H3 Metro Global Mirror initial start command. This command creates Metro
Mirror relationships between H1 and H2, and Global Mirror relationships
between H2 and H3. For Metro Global Mirror, this includes the J3
volume to complete the Global Mirror configuration. (The J3 volume role
is the journal volume at Site 3). Start H1 → H2 → H3 can be used from
some Metro Global Mirror configurations to return to the starting H1 →
H2 → H3 configuration.

Start H1 → H3 From the H1 → H2 → H3 configuration, this command changes the

session configuration to a Global Mirror-only session between H1 and
H3, with H1 as the source. Use this command in case of an H2 failure
with transition bitmap support provided by incremental
resynchronization. It can be used when a session is in the Preparing,
Prepared, and Suspended states because no source host change is
involved.

By using this command, you can bypass the H2 volume in case of an H2

failure and copy only the changed tracks and tracks in flight from H1 to
H3. After the incremental resynchronization is performed, the session is
running Global Mirror from H1 to H3 and thus loses the near-zero data
loss protection that was achieved with Metro Mirror when H1 → H2 →
H3 is run. However, data consistency is still maintained at the remote
site with the Global Mirror solution.

From H2 → H1 → H3 configuration, this command changes the session

configuration to a Global Mirror-only session configuration between H1
and H3, with H1 as the source. Use this command when the source site
has a failure and production is moved to the H1 site. This can be done
for unplanned HyperSwap. The Global Mirror session is continued. This
is a host-volume change so this command is valid only when you are
restarting the H1 → H3 configuration or from the Target Available H2 →
H1 → H3 state.

Start H2 → H1 → H3 Metro Global Mirror start command. This is the configuration that
completes the HyperSwap processing. This command creates Metro
Mirror relationships between H2 and H1 and Global Mirror relationships
between H1 and H3. For Metro Global Mirror, this includes the J3
volume to complete the Global Mirror configuration.

28 Tivoli Storage Productivity Center for Replication for Open Systems

Command Meaning

Start H2 → H3 From the H1 → H2 → H3 configuration, this command moves the

session configuration to a Global Mirror-only session configuration
between H2 and H3, with H2 as the source. Use this command when the
source site has a failure and production is moved to the H1 site. This can
be done for unplanned HyperSwap. The Global Mirror session is
continued. This is a host-volume change so this command is valid only
when you are restarting the H1 → H3 configuration or from the Target
Available H2 → H1 → H3 state.

From the H2 → H1 → H3 configuration, this command returns the

session configuration to a Global Mirror only session configuration
between H2 and H3 with H2 as the source. Use this command in case
of an H1 failure with transition bitmap support that is provided by
incremental resynchronization. It can be used when the session is in the
Preparing, Prepared, and Suspended states because there is not a
source-host change involved. Start H2 → H1 → H3 can be used from
some Metro Global Mirror configurations to return to the starting H2 →
H1 → H3 configuration.

Start H3 → H1 → H2 After recovering to H3, this command sets up the hardware to allow the
application to begin writing to H3, and the data is copied back to H1 and
H2. However, issuing this command does not ensure consistency in the
case of a disaster because only Global Copy relationships are
established to cover the long-distance copy back to Site 1.

To move the application back to H1, you can issue a suspend while in
this state to drive all the relationships to a consistent state and then
issue a freeze to make the session consistent. You can then issue a
recover followed by a start H1 → H2 → H3 to return to the original
configuration.

Start H3 → H2 Metro Global Mirror command to start Global Copy from the disaster
recovery site back to the H2 volumes. This is a host-volume change, so
this command is valid only when you are restarting the H3 → H2
configuration or from the Target Available H1 → H2 → H3 state.

Suspend H1 → H3 When H2 → H1 → H3 is run, this command issues a pause to the Global

Mirror master and causes the Global Mirror master to stop forming
consistency groups.

This command is valid only when the session is in the Prepared state.

Suspend H2 → H3 When H1 → H2 → H3 is run, this command issues a pause to the Global

Mirror master and causes the Global Mirror master to stop forming
consistency groups.

This command is valid only when the session is in the Prepared state.

Terminate Removes all physical copies from the hardware. This command can be
issued at any point in an active session.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 29

1.6 New features and enhancements in Tivoli Storage
Replication Center for Replication by release
This section describes new features and enhancements in Tivoli Storage Productivity Center
for Replication by release. For more information about a feature or enhancement, see the
New for Tivoli Storage Productivity Center Version 5.x topic in the Tivoli Storage Productivity
Center Version 5.1.1.1 information center and the New for Tivoli Storage Productivity Center
Version 5.2 topic in the Tivoli Storage Productivity Center Version 5.2 information center. You
can find the Tivoli Storage Productivity Center information center by version at Tivoli
Documentation Central, which is available at this website:
https://www.ibm.com/developerworks/community/wikis/home?lang=en#!/wiki/Tivoli%20Do
cumentation%20Central/page/Tivoli%20Storage%20Productivity%20Center

1.6.1 New in V5.1

The following features and enhancements are new in Tivoli Storage Productivity Center for
Replication V5.1.

Failover operations that are managed by other applications

Applications, such as the IBM Series i Toolkit, VMware Site Recovery Manager, and Veritas
Cluster Server, manage failover operations for certain session types and storage systems. If
an application completes a failover operation for a session, the Severe status is displayed for
the session. An error message is also generated for the role pairs for which the failover
occurred.

Additional support for space-efficient volumes in remote copy

You can use extent space-efficient volumes as copy set volumes for the following IBM System
DS8000 session types:
򐂰 FlashCopy (System Storage DS8000 v6.2 or later)
򐂰 Metro Mirror (System Storage DS8000 v6.3 or later)
򐂰 Global Mirror or Metro Global Mirror (System Storage DS8000 v6.3 or later)

Reflash After Recover for Global Mirror Failover/Failback with Practice

sessions
You can use the Reflash After Recover option with System Storage DS8000 version 4.2 or
later. Use this option to create a FlashCopy replication between the I2 and J2 volumes after
the recovery of a Global Mirror Failover/Failback with Practice session. If you do not use this
option, a FlashCopy replication is created only between the I2 and H2 volumes.

No Copy option for Global Mirror with Practice and MGM with Practice
sessions
You can use the No Copy option with System Storage DS8000 version 4.2 or later. Use this
option if you do not want the hardware to write the background copy until the source track is
written to.

30 Tivoli Storage Productivity Center for Replication for Open Systems

 Recovery Point Objective Alerts option for Global Mirror sessions
You can use the Recovery Point Objective Alerts option with ESS800, DS6000, and DS8000
storage systems. Use this option to specify the length of time that you want to set for the
recovery point objective (RPO) thresholds. The values determine whether a Warning or
Severe alert is generated when the RPO threshold is exceeded for a role pair. The RPO
represents the length of time (in seconds) of data exposure that is acceptable in the event of a
disaster.

StartGC H1 → H2 command for Global Mirror sessions

You can use the StartGC H1 → H2 command with ESS800, DS6000, and DS8000 storage
systems. This command establishes Global Copy relationships between Site 1 and Site 2,
and begins asynchronous data replication from H1 to H2.

This command is available only for Global Mirror Failover/Failback and Global Mirror
Failover/Failback with Practice sessions.

Export Global Mirror Data command for Global Mirror role pairs
You can use this option to export data for a Global Mirror role pair that is in a session to a
comma-separated value (.csv) file. You can then use the data in the .csv file to analyze
trends in your storage environment that affect your RPO.

1.6.2 New in V5.1.1

The following features and enhancements are new in Tivoli Storage Productivity Center for
Replication V5.1.1.

SAN Volume Controller 6.4 option to move volumes between I/O groups
To support this SAN Volume Controller feature, Tivoli Storage Productivity Center for
Replication includes the following changes:
򐂰 The I/O group was removed from the volume ID.
򐂰 The volume ID or the volume name can be used as a CLI command volume parameter for
SAN Volume Controller, Storwize V3500, Storwize V3700, Storwize V7000, and Storwize
V7000 Unified storage systems. The following CLI commands were updated to reflect this
change:
– chvollspair
– lscpset
– lsvol
– mkcpset (where applicable for the specific volume parameter)
– importcsv
– exportcsv
– rmcpset
– showcpset

DS8000 consistency groups that are created for FlashCopy sessions

For FlashCopy sessions, Tivoli Storage Productivity Center for Replication creates FlashCopy
consistency groups in DS8000 storage systems. The consistency groups are created
automatically during the creation of the FlashCopy session. You are no longer required to
quiesce an application before you issue the Flash command for FlashCopy sessions.

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 31

 HyperSwap options available for Metro Global Mirror with Practice
sessions
The session properties for Metro Global Mirror with Practice sessions include the same
HyperSwap options that are available for Metro Global Mirror sessions.

1.6.3 New in V5.1.1.1

The following features and enhancements are new in Tivoli Storage Productivity Center for
Replication V5.1.1.1.

DS8000 pause with consistency available for Global Mirror and Metro
Global Mirror sessions
The Tivoli Storage Productivity Center for Replication Suspend command starts a pause or
pause with secondary consistency command for DS8000 storage systems. The command
that is started is the equivalent of the DS8000 pausegmir or pausegmir -withsecondary
command, depending on the DS8000 microcode level.

Both pause commands temporarily pause the formation of consistency groups after the
current consistency group is formed. However, the command for a pause with secondary
consistency creates a consistent data set on the secondary volumes.

Easy Tier Heat Map transfer for DS8000

The DS8000 Easy Tier heat map transfer function transfers heat map information from a
source storage system to one or more target storage systems. You can enable heat map
transfers for DS8000 storage systems that are connected to Tivoli Storage Productivity
Center for Replication from the Tivoli Storage Productivity Center for Replication GUI.

The Easy Tier heat map transfer function is available in System Storage DS8000 Release 7.1
and later.

1.6.4 New in V5.2

The following features and enhancements are new in Tivoli Storage Productivity Center for
Replication V5.2.

New session type for SAN Volume Controller and Storwize

The Global Mirror Failover/Failback with Change Volumes session is available for SAN
Volume Controller and Storwize storage systems that use change volumes.

Global Mirror Failover/Failback with Change Volumes sessions provide the same capabilities
as Global Mirror Failover/Failback sessions. The difference is that Global Mirror
Failover/Failback with Change Volumes sessions also provide the option of enabling or
disabling the use of change volumes. Change volumes contain point-in-time images that are
copied from the host and target volumes.

Connect to z/OS from open systems and manage HyperSwap

You can use a host name or IP address to connect to z/OS host systems in Tivoli Storage
Productivity Center for Replication, regardless of the operating system on which the
application is installed.

32 Tivoli Storage Productivity Center for Replication for Open Systems

 By using this feature, you can connect to a z/OS host system from Tivoli Storage Productivity
Center for Replication that is running on Windows, Linux, AIX, or z/OS. After you are
connected to a host system, you can fully manage HyperSwap sessions that are running on
the system. In addition, this feature enables a single instance of Tivoli Storage Productivity
Center for Replication to manage multiple HyperSwap instances that are running in different
z/OS systems and sysplexes.

1.7 Introduction to Storage Systems

This section provides a brief description of the storage systems that are supported by Tivoli
Storage Productivity Center for Replication. The following older storage systems are not
described in this section:
򐂰 ESS800
򐂰 DS6000
򐂰 DS8800
򐂰 DS8700

1.7.1 IBM System Storage DS8000

IBM System Storage DS8000 series is a high-performance, high-capacity series of disk
storage that supports continuous operations.

The latest and most advanced disk enterprise storage system in the DS8000 series is the
IBM System Storage DS8870. It represents the latest in the series of high-performance and
high-capacity disk storage systems. The DS8870 supports IBM POWER7® processor
technology to help support higher performance.

The DS8000 series DS8870 supports functions such as point-in-time copy functions with IBM
FlashCopy, FlashCopy Space Efficient, and Remote Mirror and Copy functions with Metro
Mirror, Global Copy, Global Mirror, Metro Global Mirror, IBM z/OS Global Mirror, and z/OS
Metro/Global Mirror. Easy Tier functions are supported on DS8870 storage units. I/O Priority
Manager is also supported on the DS8870 units.

All DS8000 series models consist of a storage unit and one or two management consoles
(two is the recommended configuration). The GUI or the CLI can logically partition storage
and use the built-in Copy Services functions. For high availability, the hardware components
are redundant.

For more information about the latest functionality of IBM System Storage DS8000 products,
see this website:

http://www-03.ibm.com/systems/storage/disk/ds8000/index.html

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 33

1.7.2 IBM Storwize Family
The following products are members of the IBM Storwize family of virtualized storage
systems.

IBM System Storage SAN Volume Controller

IBM System Storage SAN Volume Controller is a storage virtualization system with a single
point of control for storage resources. SAN Volume Controller improves business application
availability and greater resource usage so you can get the most from your storage resources
and achieve a simpler, more scalable and cost-efficient IT infrastructure. The newly enhanced
SAN Volume Controller with IBM Real-time Compression™ offers up to three times the
throughput for applications.

For more information about the IBM SAN Volume Controller, see this website:
http://www-03.ibm.com/systems/storage/software/virtualization/svc/index.html

IBM Storwize V7000 and V7000 Unified

IBM Storwize V7000 and Storwize V7000 Unified are virtualized storage systems that
consolidate workloads into a single storage system for simplicity of management, reduced
cost, highly scalable capacity, performance, and high availability. These systems offer
improved efficiency and flexibility through built-in flash memory optimization, thin provisioning,
and nondisruptive migration from existing storage.

Storwize V7000 supports block workloads whereas Storwize V7000 Unified consolidates
block and file workloads into a single system. For more information about IBM Storwize
V7000 and Storwize V7000 Unified Disk Systems, see this website:

http://www-03.ibm.com/systems/storage/disk/storwize_v7000/

IBM Storwize V3500 and V3700

Storwize V3500 and Storwize V3700 are entry-level disk storage systems that are designed
with sophisticated capabilities that are unusual for a system of this class. These storage
systems offer efficiency and flexibility through built-in thin provisioning and nondisruptive
migration of data from existing storage. Built upon the innovative technology in the Storwize
family, Storwize V3500 and Storwize V3700 address block storage requirements of small and
midsize organizations. For more information about this product, see website:
http://www-03.ibm.com/systems/storage/disk/storwize_v3700/index.html

34 Tivoli Storage Productivity Center for Replication for Open Systems

1.7.3 IBM XIV Storage System
IBM XIV Storage System is high-end disk storage that supports the need for high
performance, reliability, and flexibility while helping keep costs and complexity to a minimum.
IBM XIV Storage System exemplifies IBM Smarter Storage for Smarter Computing,
empowering thousands of organizations worldwide to take control of their storage and gain
business insights from their data.

Designed for consistent Tier 1 performance and five-nines availability, XIV storage offers low
total cost of ownership and addresses even the most demanding and diverse workloads. The
IBM XIV Storage System grid architecture delivers massive parallelism, which results in
uniform allocation of system resources always. IBM XIV Storage System automates tasks
and provides an extraordinarily intuitive user interface. This interface is accompanied by an
equally rich and comprehensive CLI for tailoring the system to user requirements.

For more information about IBM XIV Storage System, see this website:
http://www-03.ibm.com/systems/storage/disk/xiv/index.html

Chapter 1. Introduction to Tivoli Storage Productivity Center for Replication 35

36 Tivoli Storage Productivity Center for Replication for Open Systems
 2

Chapter 2. Planning and installation

In this chapter, we provide an overview of the tasks that are necessary to successfully deploy
Tivoli Storage Productivity Center for Replication within your environment.

This chapter includes the following topics:

򐂰 Tivoli Storage Productivity Center for Replication installation planning
򐂰 Installing Tivoli Storage Productivity Center for Replication

© Copyright IBM Corp. 2014. All rights reserved. 37

2.1 Tivoli Storage Productivity Center for Replication
installation planning
As of Tivoli Storage Productivity Center version 5.1, Tivoli Storage Productivity Center for
Replication is a part of the IBM Tivoli Storage Productivity Center and is installed with the
Tivoli Storage Productivity Center installation. Installation planning for Tivoli Storage
Productivity Center for Replication is part of the planning for Tivoli Storage Productivity
Center, but some specific information regarding Tivoli Storage Productivity Center for
Replication must be determined. That information is described in the following sections.

2.1.1 Pre-installation steps

It is important to plan pre-installation steps to correctly set up the Tivoli Storage Productivity
Center for Replication environment. The pre-installation steps consider some specifics
regarding Tivoli Storage Productivity Center for Replication, which are also important in a
presales phase if you are planning to buy Tivoli Storage Productivity Center. The following
specifics must be considered:
򐂰 Licensing (Tivoli Storage Productivity Center for Replication, storage systems)
򐂰 Operating systems platform
򐂰 High availability configuration versus non-high availability configuration
򐂰 Management server connectivity
򐂰 Storage systems connectivity
򐂰 User accounts
򐂰 Managing HyperSwap functionality (z/OS, open systems)
򐂰 Host connectivity

For more information about the pre-installation steps and other Tivoli Storage Productivity
Center installation details, see the draft of the Tivoli Storage Productivity Center V5.2
Release Guide, SG24-8204, and the Tivoli Storage Productivity Center 5.2 Installation and
Configuration Guide, SC27-4058.

2.1.2 Licensing
With the convergence of Tivoli Storage Productivity Center for Replication function into the
Tivoli Storage Productivity Center license, there is no longer a separate license for Tivoli
Storage Productivity Center for Replication as it was in the previous Tivoli Storage
Productivity Center versions (4.x and before). The Tivoli Storage Productivity Center license
enables all Tivoli Storage Productivity Center for Replication functions, which were in the
Tivoli Storage Productivity Center for Replication Two Site and Three Site Business
Continuity. It also enables all Tivoli Storage Productivity Center functions, such as storage
resource management and reporting and performance monitoring.

Tivoli Storage Productivity Center is licensed per Terabyte (a terabyte is 2 to the 40th power
bytes) and it must cover all of your storage that is managed by Tivoli Storage Productivity
Center. The storage that is managed is the total allocated size of all volumes that are
managed by Tivoli Storage Productivity Center, whether they are replicated or not. It means if
you are using Tivoli Storage Productivity Center for Replication, the license must cover the
total allocated size of all volumes on primary and disaster recovery site.

Licenses are also concerned with storage systems where you installed copy services
licenses.

38 Tivoli Storage Productivity Center for Replication for Open Systems

2.1.3 Hardware and software requirements
In this section, we describe the hardware and software requirements for the Tivoli Storage
Productivity Center and for the Tivoli Storage Productivity Center for Replication. Because the
Tivoli Storage Productivity Center server can require a large amount of memory, disk space,
network bandwidth, and processor resources, it is recommended to use a dedicated server
that is not running other applications. Dedicated servers improve performance and make it
easier to troubleshoot errors.

Note: If you are planning to use only Tivoli Storage Productivity Center for Replication
functions, disk space requirements might be less than what is specified in the
requirements. Tivoli Storage Productivity Center for Replication does not use the DB2
database repository where all the Tivoli Storage Productivity Center history data is
collected and stored.

For more information about product lists and platform support for Tivoli Storage
Productivity Center, see the following resources:
򐂰 IBM Support web page:
http://www-01.ibm.com/support/docview.wss?uid=swg21386446
򐂰 IBM Tivoli Storage Productivity Center Information Center link:
http://pic.dhe.ibm.com/infocenter/tivihelp/v59r1/index.jsp

Hardware requirements
Tivoli Storage Productivity Center for Replication version 5.2 has the following hardware
requirements:
򐂰 Windows and Linux:
– Processor: Intel Xeon or greater; at least four processors at 2.5 GHz CPUs each
– Memory: 8 GB of RAM
– Disk space: 15 GB of free disk space
򐂰 AIX:
– Processor: IBM POWER5 or later; at least four processors at 2.3 GHz CPUs each
– Memory: 8 GB of RAM
– Disk space: 22 GB of free disk space

Software requirements for operating systems

Tivoli Storage Productivity Center for Replication version 5.2 supports the following operating
systems:
򐂰 Windows and Linux:
– Windows 2012 (x86, x86-64): Standard Edition, Enterprise Edition
– Windows 2008 R2 (x86-64): Standard Edition, Enterprise Edition
– Red Hat Enterprise Linux Base Server and Advanced Platform 5 (x86-64)
– Red Hat Linux Base Server and Advanced Platform 6 (x86-64)
򐂰 AIX:
– AIX V6.1 (64-bit)
– AIX V7.1 (64-bit)

Chapter 2. Planning and installation 39

 򐂰 VM on VMWare: VMware ESX and ESXi 3.0.x, 3.5.x, 4.0.x, 4.1.x, and 5.x:
– Red Hat Enterprise Linux 5
– Red Hat Enterprise Linux 6
– Windows 2008
– Windows 2008 R2
– Windows 2012

Note: The hardware and software requirements for the Tivoli Storage Productivity Center
for Replication are the same for the active and standby management servers for a high
availability environment.

The hardware and software requirements for the Tivoli Storage Productivity Center for
Replication for System Z are documented in the IBM Redbooks publication Tivoli Storage
Productivity Center for Replication for Series z, SG24-7563, which is available at this
website:

http://pic.dhe.ibm.com/infocenter/tivihelp/v59r1/index.jsp

Storage system requirements

Tivoli Storage Productivity Center for Replication supports the following storage systems:
򐂰 DS8000
򐂰 SAN Volume Controller
򐂰 Storwize family
򐂰 Storwize Unified
򐂰 XIV
򐂰 DS6000
򐂰 ESS800

To provide replication management tasks, the storage systems must include supported
firmware and network connectivity to Tivoli Storage Productivity Center for Replication
management servers. For more information about the storage systems and corresponding
supported firmware, see this website:

http://www-01.ibm.com/support/docview.wss?uid=swg27027303#vendorstorage

The storage systems must also feature activated copy services licenses, which are used.
Some of the licenses are provided by default with storage systems, and some must be bought
separately.

Web browser requirements

Tivoli Storage Productivity Center for Replication uses the GUI to provide a single point of
control to configure, manage, and monitor copy services. Whether you start it on the server
where the Tivoli Storage Productivity Center for Replication is installed or on a remote
system, the GUI is web-based and displayed in a browser. For more information about the
certified versions of supported web browsers for the Tivoli Storage Productivity Center for
Replication, see this website:
http://www-01.ibm.com/support/docview.wss?rs=40&context=SSBSEX&context=SSMN28&cont
ext=SSMMUP&context=SS8JB5&context=SS8JFM&uid=swg21386446&loc=en_US&cs=utf-8&lang=e
n

40 Tivoli Storage Productivity Center for Replication for Open Systems

 Note: The browser levels that are listed in Table 2-1 on page 42 were tested and certified
by Tivoli Storage Productivity Center. Tivoli Storage Productivity Center supports later
versions of the browsers if the vendors do not remove or disable functionality that Tivoli
Storage Productivity Center relies on. For browser levels that are higher than the levels that
were certified with Tivoli Storage Productivity Center, customer support accepts
usage-related and defect-related service requests.

For the operating system and virtualization environments, if IBM support cannot re-create
the issue in our lab, we might ask the client to re-create the problem on a certified browser
version to determine whether a product defect exists. Defects are not accepted for
cosmetic differences between browsers or browser versions that do not affect the
functional behavior of the product. If a problem is identified in Tivoli Storage Productivity
Center, defects are accepted. If a problem is identified with the browser, IBM might
investigate potential solutions or workarounds that the client can implement until a
permanent solution becomes available.

A minimum screen resolution of 1280 x 1024 is suggested for the web browsers.

Repository requirements
Tivoli Storage Productivity Center for Replication uses an embedded repository where all
information about storage systems and copy services configuration are stored. As the Tivoli
Storage Productivity Center for Replication is installed with Tivoli Storage Productivity Center
installation, the embedded repository is automatically created. There are no other
requirements for the repository and the repository also does not require more setup.

Before you install Tivoli Storage Productivity Center, you must install DB2 database because
DB2 database is required for the Tivoli Storage Productivity Center database repository. DB2
license key must also be registered.

2.1.4 Configuration planning

This section describes physical planning and TCP/IP ports that are used for configuring Tivoli
Storage Productivity Center and Tivoli Storage Productivity Center for Replication. Also
provided is high availability configuration planning when you have Tivoli Storage Productivity
Center for Replication installed on two servers with one server running in active mode and the
second server running in standby mode.

Physical planning and TCP/IP ports used

Tivoli Storage Productivity Center for Replication uses an Internet Protocol network to
communicate with storage systems. Therefore, you must ensure that your Tivoli Storage
Productivity Center for Replication server has the necessary access to all required storage
systems.

When you install Tivoli Storage Productivity Center and Tivoli Storage Productivity Center for
Replication, default ports must be opened through the firewall. You must also disable the
firewall program or open the ports to allow incoming requests to the Tivoli Storage
Productivity Center and Tivoli Storage Productivity Center for Replication ports.

The Table 2-1 on page 42 shows the ports that are used by Tivoli Storage Productivity Center
for Replication for incoming and outgoing communication. Review these ports before you
install the Tivoli Storage Productivity Center and Tivoli Storage Productivity Center for
Replication to establish communication to storage systems.

Chapter 2. Planning and installation 41

 The TCP/IP ports that are used only by Tivoli Storage Productivity Center are documented in
the draft of the Tivoli Storage Productivity Center V5.2 Release Guide, SG24-8204 and in the
IBM Tivoli Storage Productivity Center 5.2 Installation and Configuration Guide, SC27-4058.

Note: Table 2-1 lists default ports that are used by Tivoli Storage Productivity Center for
Replication for incoming and outgoing communication. The installer automatically detects
conflicts and might choose other ports.

Table 2-1 TCP/IP ports that are used by Tivoli Storage Productivity Center for Replication
Port Description Communication

9558 and 9559 A web browser typically Incoming

communicates with the Tivoli
Storage Productivity Center for
Replication GUI by using HTTP
ports 9558 and 9559.

9560 The Tivoli Storage Productivity Incoming

Center for Replication
command line and GUI typically
communicate with the Tivoli
Storage Productivity Center for
Replication server by using port
9560.

9561 Tivoli Storage Productivity Incoming

Center for Replication uses port
9561 for communication with
other Tivoli Storage Productivity
Center for Replication servers
for high-availability purposes.

2433 For communication with Outgoing

ESS/DS (direct connection).

1750 For communication with Outgoing

DS8000 (HMC connection).

443 and 22 For communication with SAN Outgoing

Volume Controller or Storwize
V7000 clusters.

9930 For communication with the AIX Outgoing

host for the Open HyperSwap.

A number 1 - 65535 (the port For communication with the Outgoing

number must be the same as z/OS host for the HyperSwap
the port number that is and enabling hardened freeze.
specified for the HyperSwap
management address space
IOSHMCTL SOCKPORT
parameter on the z/OS system)

42 Tivoli Storage Productivity Center for Replication for Open Systems

 Note: The following recommendations should be considered when you are planning
TCP/IP ports for Tivoli Storage Productivity Center for Replication:
򐂰 If you changed ports 9558 or 9559 during the installation or changed other port
settings, make a note of the values to which these settings were changed.
򐂰 If you changed the port configuration of your storage controller, the ports are different.
򐂰 Your network configuration must allow for Tivoli Storage Productivity Center for
Replication to send outgoing TCP/IP packets to the storage controllers. It is possible to
set a specific port number for your storage controller when you are adding the storage
controllers to Tivoli Storage Productivity Center for Replication.
򐂰 Because there often are multiple applications that are running on a server, it is possible
that port conflicts might arise if other applications attempt to use the same ports that
Tivoli Storage Productivity Center for Replication is using. You can find the port
numbers that are used on your system by running the netstat -an command.
򐂰 If firewalls are used in your configuration, make sure that none of these ports are
blocked. Ensure that not only is the Tivoli Storage Productivity Center for Replication
server granted access to reach the other components, but that the other components
are granted access to reach the Tivoli Storage Productivity Center for Replication
server.
򐂰 If you are running Windows Server 2008, you must configure the inbound and outbound
rules for Tivoli Storage Productivity Center for Replication. To create an outbound rule,
start the New Outbound Rule wizard from the Windows Firewall with Advanced Security
menu.

High availability configuration planning

If you are running in a high availability configuration in which you have Tivoli Storage
Productivity Center for Replication installed on two servers with one server running in active
mode and the second server running in standby mode, ensure that both servers can
communicate with each other and that they are authenticated through all firewalls. If the
firewall times out on either server, it requires reauthentication to open the communication
between the servers. The port that is used for high availability communication is specified in
Table 2-1 on page 42.

If you have a two- or three-site environment, your active management server can be placed in
primary or disaster recovery site. Where you place the active management server depends
on the type of sessions you are managing and the type of LAN/SAN infrastructure you have,
but we recommend placing the active server in primary site. For more information about the
high availability configuration, see Chapter 3, “General administration and high availability” on
page 61.

2.1.5 User accounts

The user name that you use to install Tivoli Storage Productivity Center must belong to the
operating system groups that are mapped to administrator role. The user that you specify as
the common user (which can be the same user that is used for installation) during the Tivoli
Storage Productivity Center installation must also belong to these groups. If you specify a
user that is not in an administrator role, your installation fails with the error that is shown in
Figure 2-1 on page 44.

Chapter 2. Planning and installation 43

 Figure 2-1 Common Username and Password

The Tivoli Storage Productivity Center installation program automatically maps the following
groups to the Tivoli Storage Productivity Center Administrator role:
򐂰 Administrators (Windows)
򐂰 System (AIX)
򐂰 Root (Linux)

The user name that is used to install the Tivoli Storage Productivity Center database
repository must belong to DB2 administrator groups. That user name depends on your
installation configuration. If you use the same common user that is used for the Tivoli Storage
Productivity Center installation, this common user must have DB2 privileges. The following
DB2 administrator groups are available:
򐂰 DB2ADMNS (Windows)
򐂰 db2iadm1 (AIX and Linux)

Note: The Tivoli Storage Productivity Center database repository must be installed before
you start Tivoli Storage Productivity Center installation.

You can also use a Windows domain common user account for Tivoli Storage Productivity
Center installation. This user must also belong to the operating system groups that are
mapped to administrator role and to DB2 administrator groups.

44 Tivoli Storage Productivity Center for Replication for Open Systems

 Note: For more information about installation instructions to install Tivoli Storage
Productivity Center in a domain, see the IBM Tivoli Storage Productivity Center Version 5.2
Installation and Configuration Guide, SC27-4058.

After you install Tivoli Storage Productivity Center, you can assign roles to users. Roles
determine the product functions that are available to users.

For more information about roles and how to assign a role to a group, see section 3.5, “Tivoli
Storage Productivity Center for Replication security and user administration” on page 93.

2.1.6 HyperSwap configuration for z/OS and Open systems

HyperSwap is a function with the Metro Mirror replication method on DS8000 storage
systems that is designed to automatically fail over I/O from the primary logical devices to the
secondary logical devices in the event of a primary disk storage system failure. This function
can be done with minimal disruption to the applications that are using the logical devices.

In previous versions of Tivoli Storage Productivity Center for Replication for Open Systems, it
was possible to manage Open HyperSwap replication for AIX hosts only, as shown in
Figure 2-2.

Figure 2-2 Tivoli Storage Productivity Center for Replication and Open HyperSwap

With Tivoli Storage Productivity Center for Replication version 5.2, you can manage the z/OS
HyperSwap function from an Open System. By using this feature, you can connect to a z/OS
host system from Tivoli Storage Productivity Center for Replication that is running on
Windows, Linux, or AIX to fully manage HyperSwap sessions that are running on a z/OS host
system.

Chapter 2. Planning and installation 45

 In addition, this feature enables a single instance of Tivoli Storage Productivity Center for
Replication to manage multiple HyperSwap instances that running in different z/OS systems
and sysplexes. Figure 2-3 shows you how to manage z/OS HyperSwap function from Tivoli
Storage Productivity Center for Replication on an Open System.

Figure 2-3 Tivoli Storage Productivity Center for Replication and z/OS HyperSwap

Planning for Open HyperSwap and z/OS HyperSwap includes the following requirements:
򐂰 DS8000 storage system with Metro Mirror
򐂰 AIX requirements for Open HyperSwap
򐂰 z/OS requirements for HyperSwap
򐂰 Hosts connectivity

We describe these requirements in this section. For more information about new z/OS
HyperSwap functions, see Chapter 7, “Managing z/OS HyperSwap from Tivoli Storage
Productivity Center for Replication for Open Systems” on page 355.

DS8000 requirements for Open HyperSwap and z/OS HyperSwap

To use Open HyperSwap and z/OS HyperSwap, your DS8000 must be on version 5.1 or later
and a Metro Mirror relationship must be established between primary and secondary
DS8000.

Both DS8000 storage systems must be connected to a host to perform HyperSwap and
automatically failover I/O from the primary logical devices to the secondary logical devices.

46 Tivoli Storage Productivity Center for Replication for Open Systems

 Open HyperSwap requirements
Open HyperSwap support requires AIX version 5.3 or 6.1. You must have the following AIX
modules installed:
򐂰 Subsystem Device Driver Path Control Module (SDDPCM) version 3.0.0.0 or later
򐂰 Multi-Path Input/Output (MPIO) module (the version that is provided with AIX version 5.3
or 6.1)

Note: For more information about the supported AIX version for each Tivoli Storage
Productivity Center for Replication release, see the support matrix at this website:

http://www.ibm.com/support/docview.wss?rs=40&context=SSBSEX&context=SSMN28&cont
ext=SSMMUP&context=SS8JB5&context=SS8JFM&uid=swg21386446&loc=en_US&cs=utf-8&lan
g=en

Clustering environments, such as VIO and PowerHA, are not supported by Open
HyperSwap.

z/OS HyperSwap requirements

z/OS HyperSwap support requires z/OS 1.12 or later and it requires that HyperSwap address
spaces, the HyperSwap Management address space, and the HyperSwap API address
space are started and running. These address spaces must be running in z/OS systems and
sysplexes that use HyperSwap function.

For more information about how to set up z/OS HyperSwap, see Chapter 7, “Managing z/OS
HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems” on
page 355.

Hosts connectivity
Tivoli Storage Productivity Center for Replication uses the Internet Protocol network to
communicate with hosts to use HyperSwap. You must ensure that your Tivoli Storage
Productivity Center for Replication server has the necessary access to all required hosts that
are involved in HyperSwap (AIX or z/OS).

Table 2-1 on page 42 shows you the ports that are used by Tivoli Storage Productivity Center
for Replication for communication with AIX and z/OS host.

2.2 Installing Tivoli Storage Productivity Center for Replication

In this section, we provide an overview of the latest Tivoli Storage Productivity Center installer
and Tivoli Storage Productivity Center installation packages. We also provide a high-level
overview of the Tivoli Storage Productivity Center installation steps.

Note: For more information about steps and requirements for installing Tivoli Storage
Productivity Center, see the draft of the Tivoli Storage Productivity Center V5.2 Release
Guide, SG24-8204.

Chapter 2. Planning and installation 47

2.2.1 Overview
As of Tivoli Storage Productivity Center 5.1, a new installer provides a more unified
installation experience across Tivoli Storage Productivity Center and Tivoli Storage
Productivity Center for Replication. The entire Tivoli Storage Productivity Center installer is
rearchitected and rewritten to simplify installation and postinstallation configuration tasks. It is
based on Install Anywhere Software and all unnecessary steps are masked.

With the new Tivoli Storage Productivity Center installer, Tivoli Storage Productivity Center for
Replication is installed without starting Tivoli Storage Productivity Center for Replication
installer as it was in the previous Tivoli Storage Productivity Center 4.x versions. By installing
Tivoli Storage Productivity Center 5.2, Tivoli Storage Productivity Center for Replication is
installed with the same user ID, which ran the installer. If you are upgrading from the previous
versions, all Tivoli Storage Productivity Center for Replication configurations remain
unchanged.

Because all Tivoli Storage Productivity Center for Replication functions and features
converged into Tivoli Storage Productivity Center 5.1/5.2 license, the installer installs Tivoli
Storage Productivity Center for Replication with all the features and functions that were
available in Tivoli Storage Productivity Center for Replication Two Site and Tivoli Storage
Productivity Center for Replication Three Site Business Continuity. This means that you do
not need to have separate Tivoli Storage Productivity Center for Replication products to run
two or three sites solutions (for example, Metro Mirror, Global Mirror, and Metro/Global
Mirror).

These features and functions are integrated and installed with Tivoli Storage Productivity
Center 5.1/5.2.

2.2.2 Tivoli Storage Productivity Center installation packages

Before Tivoli Storage Productivity Center 5.2 is installed, you must install DB2 database
because DB2 database is required for the Tivoli Storage Productivity Center database
repository. Tivoli Storage Productivity Center installation packages include the following DB2
installation images:
򐂰 DB2 10.1 Fix Pack 2 for Windows (64-bit)
򐂰 DB2 10.1 Fix Pack 2 for Linux (64-bit)
򐂰 DB2 10.1 Fix Pack 2 for AIX (64-bit)

Apart from the DB2 installation images, Tivoli Storage Productivity Center includes the
following images:
򐂰 Tivoli Storage Productivity Center for AIX
򐂰 Tivoli Storage Productivity Center for Linux
򐂰 Tivoli Storage Productivity Center for Windows

Each of the Tivoli Storage Productivity Center installation image includes the following files:
򐂰 Part 1:
– Tivoli Storage Productivity Center installation program
– Base Tivoli Storage Productivity Center components
– Database repository
– Data server
– Storage Resource agent
– Stand-alone GUI and command-line interface

48 Tivoli Storage Productivity Center for Replication for Open Systems

 򐂰 Part 2:
– Device server
– Embedded IBM WebSphere® Application Server
򐂰 Part 3:
– Web server (the web-based GUI and TPC_VMWareVSpherePlugin folder)
– Replication server
– WebSphere Application Server Liberty Profile
򐂰 JazzSM 1.1
򐂰 WebSphere Application Server 8.5.0.1(used by replication and device servers)
򐂰 Tivoli Common Reporting 3.1.1 and Cognos 10.2
򐂰 Tivoli Common Reporting Prerequisite checker

Each of these images must be concatenated into one installation directory, the name of which
cannot include any special blanks. The best way to perform this process is to create an
installation directory, for example tpcinstall, and then extract or copy images into it. When
the extract or copy is complete, you are ready to install Tivoli Storage Productivity Center.

For more information about the installation packages, see Tivoli Storage Productivity Center
5.2 Installation and Configuration Guide, SC27-4058.

2.2.3 Tivoli Storage Productivity Center installation

After you successfully extract the images, you can start with Tivoli Storage Productivity
Center installation. The installation includes the following steps:
1. DB2 installation.
2. JazzSM 1.1 installation (optional).
3. Tivoli Common Reporting 3.1.1 and Cognos 10.2 installation (optional).
4. Tivoli Storage Productivity Center installation.

If you are not planning to use Tivoli Storage Productivity Center reports, the installation of
JazzSM 1.1, Tivoli Common Reporting 3.1.1, and Cognos 10.2 can be done later. Tivoli
Storage Productivity Center is installed without reporting capabilities and the Tivoli Storage
Productivity Center web-based GUI shows you that reporting is unavailable (see Figure 2-4
on page 50).

Tivoli Storage Productivity Center for Replication does not use Tivoli Storage Productivity
Center reporting, but some reports might be useful for monitoring replication; for example,
ports performance.

Chapter 2. Planning and installation 49

 Figure 2-4 Web-based GUI reporting

Before DB2 is installed, review the prerequisites and follow the steps that are described in the
draft of Tivoli Storage Productivity Center V5.2 Release Guide, SG24-8204, and Tivoli
Storage Productivity Center 5.2 Installation and Configuration Guide, SC27-4058. After you
successfully install DB2, you can install JazzSM 1.1, Tivoli Common Reporting 3.1.1, and
Cognos 10.2, or you can install it later.

For more information about the steps and requirements, see the draft of Tivoli Storage
Productivity Center V5.2 Release Guide, SG24-8204, and Tivoli Storage Productivity Center
5.2 Installation and Configuration Guide, SC27-4058.

After you install DB2, you can start your Tivoli Storage Productivity Center installation by
using the installation wizard or the command line in silent mode. In silent mode, a command
is provided with the values in a response file. We recommend the use of the installation
wizard to install Tivoli Storage Productivity Center because it requires minimal user
interaction. If the system where you want to install Tivoli Storage Productivity Center is
running from a terminal that cannot display graphics, use silent mode installation.

Note: Before you start the Tivoli Storage Productivity Center installation wizard on AIX or
Linux servers, you must source the user profile (db2profile) for the instance owner of the
DB2 database, as shown in the following example:

. /home/db2inst1/sqllib/db2profile

You also must have X Window System support to display the installation wizard GUI.

Start the Tivoli Storage Productivity Center installation program from your installation
directory by running the setup.bat program, which starts InstallAnywhere wizard, as shown
in Figure 2-5 on page 51.

50 Tivoli Storage Productivity Center for Replication for Open Systems

 Note: On AIX and Linux servers, you start the installation program by running the
./setup.bin command from the installation directory where you extracted Tivoli Storage
Productivity Center images.

Figure 2-5 Starting Tivoli Storage Productivity Center installation

In the window that is shown in Figure 2-6, you select the installation language and click OK.

Figure 2-6 Tivoli Storage Productivity Center language window

Chapter 2. Planning and installation 51

 After you accept license agreement (as shown in Figure 2-7), you see Tivoli Storage
Productivity Center prerequisites, as shown in Figure 2-8 on page 53.

Figure 2-7 Tivoli Storage Productivity Center License Agreement window

52 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 2-8 Tivoli Storage Productivity Center Prerequisites window

If JazzSM is installed on your computer, the page displays a green check mark; otherwise, the
Install Now button is shown. If you do not want to install JazzSM on your computer, click Next
to proceed to the next page in the Tivoli Storage Productivity Center installation program and
install Tivoli Storage Productivity Center without reports. In our case, we do not install
reporting. Click Next.

The window that is shown in Figure 2-9 on page 54 shows your installation location and type.
We select single server as installing Tivoli Storage Productivity Center in a single-server
environment. This is a simple process and can be completed successfully by most Tivoli
Storage Productivity Center customers.

Chapter 2. Planning and installation 53

 Figure 2-9 Tivoli Storage Productivity Center Installation Location and Type window

A multiple-server environment is ideal if you are monitoring large storage environments,

where one server is not sufficient to manage the Tivoli Storage Productivity Center
components. In this environment, JazzSM and Tivoli Common Reporting can run on a
separate server. This environment facilitates the integration with other Tivoli products that are
using JazzSM and Tivoli Common Reporting components and allows the sharing of
components that are installed on a separate server. If you have different administrators for
DB2 and Tivoli Storage Productivity Center, this environment allows the database repository
and DB2 to be installed and managed on a separate server. Tivoli Storage Productivity
Center for Replication is installed together with Tivoli Storage Productivity Center server.

Click Next. In the window that is shown in Figure 2-10 on page 55, specify the host name and
ports that are used by Tivoli Storage Productivity Center. Also, specify the user name and
password of the common user to configure all Tivoli Storage Productivity Center components.
This user name must have the correct DB2 and operating system privileges.

Tip: Some systems might be configured to return a short host name, such as server22,
instead of a fully qualified host name, such as server22.myorg.mycompany.com. Tivoli
Storage Productivity Center requires fully qualified host names, so you must install the
software on a computer that has a fully qualified host name.

54 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 2-10 Tivoli Storage Productivity Center Server Installation Information window

If the default ports are unavailable, you can specify a different range that is used by Tivoli
Storage Productivity Center. To check whether the ports are available, click Verify port
availability. You can also change details about database repository by clicking Configure
Database Repository.

If all the information is correct, you see the pre-installation summary page that is shown in
Figure 2-11 on page 56.

Chapter 2. Planning and installation 55

 Figure 2-11 Tivoli Storage Productivity Center Pre installation Summary

If you click Additional Installation Information, you see all of the components that are
installed, including Tivoli Storage Productivity Center for Replication (Replication server), as
shown in Figure 2-12.

Figure 2-12 Tivoli Storage Productivity Center components

56 Tivoli Storage Productivity Center for Replication for Open Systems

Click Install to start the installation. You see the progress of the installation and that Tivoli
Storage Productivity Center for Replication is being installed, as shown in Figure 2-13.

Figure 2-13 Tivoli Storage Productivity Center installation window

Chapter 2. Planning and installation 57

 The window that is shown in Figure 2-14 shows that you successfully completed Tivoli
Storage Productivity Center installation.

Figure 2-14 Tivoli Storage Productivity Center Installation completed window

The links that are shown in the window in Figure 2-14 are used to start Tivoli Storage
Productivity Center Web GUI and Tivoli Storage Productivity Center for Replication GUI. You
can find the shortcuts to these links by clicking Start → All Programs → IBM Tivoli Storage
Productivity Center, as shown in Figure 2-15 on page 59.

Click Done to finish the installation.

58 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 2-15 Start Tivoli Storage Productivity Center

After you install Tivoli Storage Productivity Center, you can verify whether the installation was
successful. We describe here how to check whether the Tivoli Storage Productivity Center for
Replication is successfully installed and running. For more information about how to check
other Tivoli Storage Productivity Center components, see Tivoli Storage Productivity Center
5.2 Installation and Configuration Guide, SC27-4058.

In a command prompt on the Windows operating system, go to the directory

TPC_installation_directory\wlp\bin\ where TPC_installation_directory is the top-level
directory where you installed Tivoli Storage Productivity Center (for example,
C:\Program Files\IBM\TPC\). Run the server.bat status replicationServer command and
you see whether the replication server is running, as shown in Figure 2-16.

Figure 2-16 Verify Tivoli Storage Productivity Center for Replication Server

In a command-line window on the AIX or Linux operating system, go to the

TPC_installation_directory/wlp/bin/ where TPC_installation_directory is the top-level
directory where you installed Tivoli Storage Productivity Center (for example, /opt/IBM/TPC/).
Run the ./server status replicationServer command and you see whether the replication
server is running.

Chapter 2. Planning and installation 59

60 Tivoli Storage Productivity Center for Replication for Open Systems
 3

Chapter 3. General administration and high

availability
In this chapter, we show you how to perform general administration tasks in Tivoli Storage
Productivity Center for Replication.

We provide an overview of the graphical user interface (GUI) and the command-line interface
(CLI), describe the Tivoli Storage Productivity Center for Replication user administration, and
show how to configure some basic settings of Tivoli Storage Productivity Center for
Replication. We also describe the steps that are used for adding and connecting supported
storage systems, and adding and connecting hosts to Tivoli Storage Productivity Center for
Replication.

We also show you how to set up Tivoli Storage Productivity Center for Replication servers for
high availability and the process of performing a takeover from the active Tivoli Storage
Productivity Center for Replication server to the standby server.

Administration and configuration tasks that are related to Tivoli Storage Productivity Center
for Replication sessions for specific storage subsystems, Copy Sets, Paths, and Storage
Subsystems are not covered in this chapter, but are described in other chapters in this book.

This chapter includes the following topics:

򐂰 Accessing Tivoli Storage Productivity Center for Replication
򐂰 GUI overview
򐂰 CLI Overview
򐂰 Tivoli Storage Productivity Center for Replication interaction with Tivoli Storage
Productivity Center
򐂰 Tivoli Storage Productivity Center for Replication security and user administration
򐂰 Tivoli Storage Productivity Center for Replication advanced tools
򐂰 Tivoli Storage Productivity Center for Replication Console
򐂰 Tivoli Storage Productivity Center for Replication High Availability
򐂰 Starting and stopping the Tivoli Storage Productivity Center for Replication server

© Copyright IBM Corp. 2014. All rights reserved. 61

 򐂰 Using CSV files for importing and exporting sessions
򐂰 Backing up and restoring a repository
򐂰 Tivoli Storage Productivity Center for Replication SNMP management
򐂰 Adding and connecting to storage systems
򐂰 Adding and connecting host systems

62 Tivoli Storage Productivity Center for Replication for Open Systems

3.1 Accessing Tivoli Storage Productivity Center for
Replication
Tivoli Storage Productivity Center for Replication provides the following user interfaces for
managing storage system data replication and disaster recovery:
򐂰 Tivoli Storage Productivity Center for Replication GUI
򐂰 Tivoli Storage Productivity Center for Replication CLI

In this section, we describe how to use the GUI and CLI interfaces and the main features and
functions of both interfaces.

3.1.1 Accessing Tivoli Storage Productivity Center for Replication GUI

After you successfully install Tivoli Storage Productivity Center, you can access Tivoli Storage
Productivity Center for Replication to start managing data replication. By installing Tivoli
Storage Productivity Center, shortcuts to Tivoli Storage Productivity Center for Replication
are created in the Start menu on the server that is running the Windows operating system. If
you are running an AIX or Linux operating system, start a supported web browser and enter
the address of Tivoli Storage Productivity Center for Replication server.

To start the GUI on a Windows server, click Start → All Programs → IBM Tivoli Storage
Productivity Center → TPC Replication Manager GUI, as shown in Figure 3-1.

Figure 3-1 Starting Tivoli Storage Productivity Center for Replication on Windows server

The web browser starts and you see the Tivoli Storage Productivity Center for Replication
login panel, as shown in Figure 3-2 on page 64.

Chapter 3. General administration and high availability 63

 Figure 3-2 Tivoli Storage Productivity Center for Replication login panel

Enter your user name and password and the Tivoli Storage Productivity Center for Replication
Overview panel opens, as shown in Figure 3-3.

Figure 3-3 Tivoli Storage Productivity Center for Replication Health Overview panel

You can also start Tivoli Storage Productivity Center for Replication in a supported web
browser by entering the address of Tivoli Storage Productivity Center for Replication server.
This method is also used to start Tivoli Storage Productivity Center for Replication on servers
that are running AIX or Linux operating system.

64 Tivoli Storage Productivity Center for Replication for Open Systems

 To start Tivoli Storage Productivity Center for Replication enter the following address in a
browser:
https://hostname:port/CSM

Hostname in the address is the Tivoli Storage Productivity Center for Replication server. You
can also specify the host name as an IP address or a Domain Name System (DNS) name.

Port is the port number for Tivoli Storage Productivity Center for Replication. The default port
number for connecting to Tivoli Storage Productivity Center for Replication by using the
HTTPS protocol is 9559. However, this port number might be different for your site, so enter
the port that you specified during the installation.

3.1.2 Accessing Tivoli Storage Productivity Center for Replication CLI

To start Tivoli Storage Productivity Center for Replication CLI on a Windows server, you must
run the csmcli.bat command from your default Tivoli Storage Productivity Center installation
directory TPC_Install\Program Files\IBM\TPC\cli. This command opens the CLI window,
as shown in Figure 3-4. If you did not set up the CLI properties file, the CLI prompts you to
enter a user name and password to log on to the server.

Figure 3-4 Tivoli Storage Productivity Center for Replication CLI window

On AIX and Linux servers, you must run the csmcli.sh command script from the default Tivoli
Storage Productivity Center for Replication installation directory /opt/IBM/TPC.

You can run CLI commands locally from the Tivoli Storage Productivity Center for Replication
management server or remotely by accessing the management server by using a
remote-access utility (SSH or telnet).

3.2 GUI overview

The Tivoli Storage Productivity Center for Replication GUI is a web-based interface that
presents the user a single point of control to configure, manage, and monitor the copy
services of the attached storage subsystems. The GUI reports the state of availability of the
administration components and information for the established copy operations in real time. It
also reports the state of Tivoli Storage Productivity Center for Replication standby server if
you set up the high availability configuration.

The GUI contains the following features and functions, as shown in the panel that opens when
you log in to the GUI, as shown in Figure 3-5 on page 66:
1. Navigation tree: Provides categories of tasks that you can complete in Tivoli Storage
Productivity Center for Replication. Clicking a task opens a main page in the content pane.

Chapter 3. General administration and high availability 65

 2. Health Overview: Shows a status summary for all sessions, storage systems, host
systems, and management servers that Tivoli Storage Productivity Center for Replication
is managing.
3. Content area: Displays content that is based on the item that you selected in the
navigation tree.

Figure 3-5 Tivoli Storage Productivity Center for Replication GUI Health Overview

3.2.1 GUI panels

In this section, we describe the Tivoli Storage Productivity Center for Replication GUI and its
associated panels.

Health Overview panel

As shown in Figure 3-5, the Health Overview panel is the first panel that you see after you log
in. This panel provides the following information:
򐂰 Overall session status: Indicates the sessions statuses, which can be normal, warning, or
severe.
򐂰 Overall storage systems status: Indicates the connection status of the storage systems.
򐂰 Overall host systems status: Indicates the connection status of host systems. This status
applies to AIX and z/OS system hosts.
򐂰 Management server status: Indicates the status of the standby server if you are logged on
to the local server. If you are logged on to the standby server, this status indicates the
status of the local server.

66 Tivoli Storage Productivity Center for Replication for Open Systems

Tivoli Storage Productivity Center for Replication uses the following color-based status
indicators to provide a quick overview of the overall state of specific Tivoli Storage
Productivity Center for Replication components.
򐂰 Green: Tivoli Storage Productivity Center Copy Services is in “normal” mode. The session
is in prepared state for all defined volumes and maintaining a current consistent copy of
the data. Green also is used if the session successfully processed a Recover command
and is in Target Available state with all volumes consistent and no exceptions.
򐂰 Yellow: Tivoli Storage Productivity Center Copy Services is not maintaining a current
consistent copy now but is working toward that goal. That is, sessions might have volumes
that are actively copied or pending to be copied, there are no suspended volumes, and
copy services is temporarily inconsistent but actions are in place to move into duplex state.
No action is required to make this status Green because states automatically change.
򐂰 Red: Tivoli Storage Productivity Center Copy Services has one or more exceptions that
must be dealt with immediately.

In addition, various icons are used to represent a more detailed status of different objects, as
shown in Table 3-1.

Table 3-1 Tivoli Storage Productivity Center Symbols

Symbol Meaning
The sessions are in a normal state.

The sessions are in the warning state.

The sessions are in an error state.

The storage systems are connected to the management server.

At least one storage system cannot communicate with the management servers.

At least one storage subsystem cannot communicate with the management servers.

No storage subsystems are defined.

The session is in an inactive state.

The standby server is defined and synchronized.

The standby server is in warning status (disconnected, synchronizing).

Chapter 3. General administration and high availability 67

 Symbol Meaning
No standby server is defined.

The standby server cannot communicate with the local server.

Sessions panel
The Session panel (as shown in Figure 3-6) provides you information about all sessions,
including statistics. From this panel, you can complete all actions for the sessions you
defined, or you can create a session. The actions depend on the type of session.

Figure 3-6 Sessions panel

Storage Systems panel

As shown in Figure 3-7 on page 69, the Storage Systems panel shows you defined storage
systems and their connection status to local and remote management servers. It also shows
you locations, types, and vendors. From this panel, you can add or remove storage system
and their connections, view volumes, paths, and storage details. You can also enable or
disable Easy Tier Heat Map Transfer.

68 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 3-7 Storage Systems panel

Host Systems panel

The Host Systems panel shows you the connected host systems and information about these
systems, as shown in Figure 3-8. From this panel, you can add or remove hosts and modify
the host connection. There are two types of host systems to which you can connect: an AIX
host system or an z/OS host system. Host Systems connections are used when you want to
use Open HyperSwap feature for AIX and z/OS HyperSwap.

Figure 3-8 Host Systems

Volumes panel
The Volumes panel that is shown in Figure 3-9 on page 70 shows you details about the
volumes that are associated with a storage system; for example, the type and capacity of the
volume and connection to host.

Chapter 3. General administration and high availability 69

Figure 3-9 Volumes panel

ESS/DS Paths panel

The ESS/DS Paths panel shows you the defined paths for storage systems. You can view and
manage the paths for DS8000, DS6000, and ESS800 storage systems. By using this panel,
you start the Path Management wizard to add a path between a source and target storage
system. After you add the paths, you can view them in this panel, as shown in Figure 3-10.

Figure 3-10 ESS/DS Paths panel

For more information about how to define paths, see 4.3.1, “DS8000 Path management” on
page 201.

Management Servers panel

Use the Management Servers panel to define a standby server and view the status of the
management servers configuration. If you defined the standby server, the list shows you both
management servers in operation.

This panel has two variations, depending on which management server you are logged in.
Actions are also different and they are related to each management server. The actions can
be Reconnect, Takeover, Define standby, Remove standby, and Set this Server as Standby.

Figure 3-11 on page 71 shows the Management Servers panel.

70 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 3-11 Management Servers panel

Administration panel
As shown in Figure 3-12, the Administration panel is used to view a list of Tivoli Storage
Productivity Center for Replication users and groups and their access privileges. You can also
give users and groups different access privileges.

Figure 3-12 Administration panel

Advanced Tools panel

Use the Advanced Tools panel that is shown in Figure 3-13 on page 72 to create a diagnostic
package in case you have a problem with Tivoli Storage Productivity Center for Replication.
You can change the automatic browser refresh rate (in seconds) to refresh the content in the
GUI.

Advanced tools also give you the option to enable or disable the Metro Mirror heartbeat,
which, is used to ensure data consistency across multiple storage systems if the Tivoli
Storage Productivity Center for Replication management server cannot communicate with
one or more storage systems.

Chapter 3. General administration and high availability 71

Figure 3-13 Advanced Tools panel

Console panel
As shown in Figure 3-14, the Console panel provides you detailed information about actions
that were taken by Tivoli Storage Productivity Center for Replication users, errors that
occurred during normal operation, and hardware error indications. You can click each
message in the console panel to get more information about the message.

For more information about Console options, see 3.7, “Tivoli Storage Productivity Center for
Replication Console” on page 103.

Figure 3-14 Console panel

72 Tivoli Storage Productivity Center for Replication for Open Systems

3.3 CLI Overview
The Tivoli Storage Productivity Center for Replication CLI gives you an option to interact with
Tivoli Storage Productivity Center for Replication and to automate Tivoli Storage Productivity
Center for Replication functions by using scripts. It is installed by default with Tivoli Storage
Productivity Center installation, and it can be installed on a remote workstation by using the
procedure that is described in “3.3.3, “Remote CLI installation” on page 75.

The Tivoli Storage Productivity Center for Replication CLI uses commands that can be used
on their own by using the associated options and arguments, or interactively by starting the
csmcli.bat program with no parameters or arguments to start an interactive session. The
commands that you can use are related to the following components:
򐂰 Sessions and copy sets
򐂰 Storage systems and connections
򐂰 Management servers
򐂰 Security

The command consists of one to four types of components, arranged in the following order:
򐂰 Command name
򐂰 One or more flags
򐂰 Each flag is followed by any flag parameters it might require
򐂰 Command parameter

Example 3-1 shows the CLI structure.

Example 3-1 CLI structure

csmcli command name -flag parameter -command parameter

The command name specifies the task that the CLI must perform. For example, lssess tells
the CLI to list sessions (as shown in Example 3-2), and mksess tells the CLI to create a
session.

Example 3-2 List sessions

csmcli> lssess
Name Status State Copy Type
============================================================================
SVC2-SVC8 GM Normal Prepared Global Mirror Failover/Failback
SVC8-SVC2 GMwP Inactive Defined Global Mirror Failover/Failback w/ Practice
SVC2-SVC8 GMwP Normal Prepared Global Mirror Failover/Failback w/ Practice
V7KR7-V7KR1 GM Inactive Defined Global Mirror Failover/Failback
SVC8 FC Warning Prepared FlashCopy

Flags modify the command. They provide more information that directs the CLI to perform the
command task in a specific way. For example, the -v flag tells the CLI to display the command
results in verbose mode. Some flags can be used with every CLI command, others are
specific to a command and are invalid when they are used with other commands. Flags are
preceded by a hyphen (-), and can be followed immediately by a space and a flag parameter.

Flag parameters provide information that is required to implement the command modification
that is specified by a flag. If you do not provide a parameter, a default value is assumed. For
example, you can specify -v on, or -v off to turn verbose mode on or off; however, if you
specify -v only, the flag parameter is assumed to be on.

Chapter 3. General administration and high availability 73

 The command parameter provides basic information that is necessary to perform the
command task. When a command parameter is required, it is always the last component of
the command and it is not preceded by a flag. Some commands permit multiple command
parameters with each parameter separated by a blank space and not a comma (unlike flag
parameters, which allow multiple values).

For more information about the CLI, see IBM Tivoli Storage Productivity Center for
Replication Command-Line Interface Reference, SC27-4089.

3.3.1 Configuring the CLI

The following properties files are used to configure the CLI:
򐂰 repcli.properties
This file contains the server and port information that us used to communicate with the
IBM Tivoli Storage Productivity Center for Replication server and the CLI. You can find it in
the directory where the CLI was installed; the default directory is
\TPC_install_directory\IBM\TPC\cli.
Example 3-3 shows the contents of this file in our system. In this example, server points to
the server where Tivoli Storage Productivity Center for Replication is running. Port is the
port to be used for communication between Tivoli Storage Productivity Center for
Replication and the CLI. It must point to the same port as specified in
communications.port in the rmserver.properties file. Otherwise, you cannot log in to the
CLI.

Example 3-3 repcli.properties example

server=WTSC64.itso.ibm.com
port=9560

򐂰 rmserver.properties
This file contains configuration information about logging, as shown in Example 3-4. It is in
the default directory \TPC_install_directory\IBM\TPC\cli.

Example 3-4 rmserver.properties example

# --------------------
# Logging and Tracing
# --------------------
log.file=cliTrace.log
log.file.maxFiles=5
log.file.maxFileSize=10240
log.file.level=ALL

򐂰 tpcrcli-auth.properties
This file contains authorization information for signing on to the CLI automatically without
entering your user name and password, as shown in Example 3-5. It is in the default
directory \TPC_install_directory\IBM\TPC\cli.

Example 3-5 tpcrcli-auth.properties

password=myPassword
username=myUsername

74 Tivoli Storage Productivity Center for Replication for Open Systems

3.3.2 Setting up automatic login to the CLI
You can set up the CLI to automatically log you in without specifying your user name or
password each time you run a csmcli command or enter the csmcli shell. Use the
tpcrcli-auth.properties file to create a persistent copy of the user name and encrypted
password to be used for automatic authentication and authorization. The password is
encrypted after you start csmcli.bat, as shown in Example 3-6.

Example 3-6 Encrypted password in tpcrcli-auth.properties file

password=2808592b3f4a4331~encrypted
username=tpcadmin

Complete the following steps to set up automatic login authentication:

1. Locate the tpcrcli-auth.properties template file in the
TPC_install_directory\IBM\TPC\cli directory.
2. Create a tpcr-cli directory in your home directory and copy the template to that directory.
3. Edit the file and change the password and user name values to your password and user
ID.
4. Start csmcli.bat or csmcli.sh or run a csmcli command to encrypt the password in the
tpcrcli-auth.properties file. You are automatically logged in to the CLI, as shown in
Example 3-7.

Example 3-7 Starting csmcli.bat procedure

Created new properties file with encrypted password:
C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties
Tivoli Storage Productivity Center for Replication Command Line Interface (CLI)
Copyright 2007, 2012 IBM Corporation
Version: 5.2.0
Build: 20130719-0641
Server: SSCTCP42-T.windows.ssclab-lj-si.net Port: 9560
Authentication file: C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties

csmcli>

3.3.3 Remote CLI installation

Tivoli Storage Productivity Center for Replication supports installation of the CLI on a remote
workstation other than the Tivoli Storage Productivity Center for Replication server.

The following options are available for the remote CLI installation:
򐂰 Copying and extracting the CLI package from Tivoli Storage Productivity Center for
Replication server
򐂰 Copying CLI program folder from Tivoli Storage Productivity Center for Replication server

Chapter 3. General administration and high availability 75

 Complete the following steps to install the CLI by using the CLI package from Tivoli Storage
Productivity Center for Replication server:
1. On the Tivoli Storage Productivity Center for Replication server, browse to the installation
directory where the client images are stored. For example, the Windows operating system
uses the path C:\Program Files\IBM\TPC\client_images, as shown in Figure 3-15.

Figure 3-15 Tivoli Storage Productivity Center for Replication client images

2. Locate the appropriate compressed file for the operating system of your computer where
you want to install the CLI, as shown in the following examples:
– TPC_CLIENT_AIX.tar
– TPC_CLIENT_LINUX.zip
– TPC_CLIENT_WIN.zip

Note: You must use the client images from the Tivoli Storage Productivity Center
installation directory only. The client images in the Tivoli Storage Productivity Center image
or download directory must not be used because they are updated by the installation
program.

76 Tivoli Storage Productivity Center for Replication for Open Systems

3. Extract the appropriate compressed file on a remote workstation. In our example, we
extracted the TPC_CLIENT_WIN.zip file on a workstation that is running the Windows
operating system, as shown in Figure 3-16.

Note: In the AIX operating system, you must extract the TPC_CLIENT_AIX.tar file into the
/opt/IBM/TPCClient folder and run the /opt/IBM/TPCClient/gui/TPCD.sh command.

In the Linux operating system, you must extract the TPC_CLIENT_LINUX.zip file into the
/opt/IBM/TPCClient folder and run the /opt/IBM/TPCClient/gui/TPCD.sh command.

Figure 3-16 Tivoli Storage Productivity Center for Replication client folder

4. Edit the repcli.properties file to include the Tivoli Storage Productivity Center for
Replication server name, as shown in Example 3-8. The server name must be the fully
qualified DNS entry or the actual IP address of the Tivoli Storage Productivity Center for
Replication server. The port must not be changed because this is a system setting and is
used to communicate with the Tivoli Storage Productivity Center for Replication server.

Example 3-8 repcli.properties file

server=172.31.83.171
port=9560

5. Edit the tpcrcli-auth.properties file to include your Tivoli Storage Productivity Center
for Replication user name and password, as shown in Example 3-9. This properties file
must be placed into the subdirectory tpcr-cli, which must be created in your home user
directory. Tivoli Storage Productivity Center for Replication access this file only if it is in
that specific subdirectory of your home user directory. In Example 3-9, we use the
Administrator home directory, which is C:\Users\Administrator.

Example 3-9 tpcrcli-auth.properties file

password=myPassword
username=myUsername

Chapter 3. General administration and high availability 77

 Important: The repcli.properties file in the client images includes the Tivoli Storage
Productivity Center for Replication server host name and port number. You do not need
to modify or edit this information. It is recommended that you configure the DNS on the
system (this can be done by editing the hosts file) instead of modifying these files.

In our example, we modify the properties file because the DNS is not configured.

6. After you change the properties files, verify that CLI works by starting it through a
command prompt or click the csmcli.bat file from the directory where it is extracted. The
CLI window opens and you can start by using CLI commands, as shown in Figure 3-17.

Figure 3-17 Tivoli Storage Productivity Center for Replication CLI

Complete the following steps to install the CLI by copying the CLI folder from Tivoli Storage
Productivity Center for Replication server on a workstation that is running the Windows
operating system:
1. Create a CLI folder on your workstation. In our example, we created the CSMCLI folder.
2. Copy the entire CLI program subfolder from your Tivoli Storage Productivity Center for
Replication server, as shown in Figure 3-18 on page 79, including all subdirectories, into
your local CSMCLI directory. The CLI folder is in default installation directory under
\Program Files\IBM\TPC\cli.

78 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 3-18 CLI folder

3. Edit the CSMJDK and CSMCLI location lines in csmcli.bat to meet your local directory
structure, as shown in Example 3-10.

Example 3-10 csmcli.bat

@echo off
TITLE IBM Replication Manager CLI
@setlocal

REM ***************************************************************************
REM Set up the environment for this specific configuration. Both
REM JAVA_HOME and CSMCLI_HOME must be defined in environment variables.
REM ***************************************************************************
set CSMJDK=C:\Program Files\IBM\TPC\jre
if "%CSMJDK%"=="" GOTO ERROR_JAVA
set CSMCLI=C:\CSMCLI
if "%CSMCLI%"=="" GOTO ERROR_CLI
set PATH=%CSMCLI%\lib;%PATH%
set
CSMCP=.;lib\csmcli.jar;lib\clicommon.jar;lib\csmclient.jar;lib\essClientApi.jar
;
set
CSMCP=%CSMCP%;lib\ibmCIMClient.jar;lib\jlog.jar;lib\jsse.jar;lib\xerces.jar;lib
\JSON4J.jar;
set
CSMCP=%CSMCP%;lib\rmmessages.jar;lib\snmp.jar;lib\ssgclihelp.jar;lib\ssgfrmwk.j
ar;
set JAVA_ARGS=
cd /d "%CSMCLI%"

Chapter 3. General administration and high availability 79

 REM ***************************************************************************
REM Find the current code page
REM ***************************************************************************

chcp > %TEMP%\chcp.txt

"%CSMJDK%\bin\java" -classpath %CSMCP%
com.ibm.storage.mdm.cli.rm.CodePageExtractor "%TEMP%\chcp.txt"
"%TEMP%\codepage.txt"
SET /P CODEPAGEVALUE= < %TEMP%\codePage.txt
if "%CODEPAGEVALUE%"=="" GOTO RUNPROG
SET JAVA_ARGS=%JAVA_ARGS% -Dfile.encoding=%CODEPAGEVALUE%

REM ***************************************************************************
REM Execute the CSMCLI program.
REM ***************************************************************************
:RUNPROG
"%CSMJDK%\bin\java" %JAVA_ARGS% -Xmx512m -Djava.net.preferIPv4Stack=false
-classpath %CSMCP% com.ibm.storage.mdm.cli.rm.RmCli %*
GOTO END

REM ***************************************************************************
REM The Java interpreter home environment variable, JAVA_HOME, is not set
REM ***************************************************************************
:ERROR_JAVA
echo The JAVA_HOME environment variable is not set. Please see documentation.
GOTO END

REM ***************************************************************************
REM The CSM CLI home environment variable, CSMCLI_HOME, is not set
REM ***************************************************************************
:ERROR_CLI
echo The CSMCLI_HOME environment variable is not set. Please see
documentation.

:END
if not %ERRORLEVEL% == 0 pause
@endlocal

4. Edit the repcli.properties file to include the Tivoli Storage Productivity Center for
Replication server name, as shown in Example 3-11. The server name must be the fully
qualified DNS entry or the actual IP address of the Tivoli Storage Productivity Center for
Replication server. The port must not be changed because this is a system setting and is
used to communicate with the Tivoli Storage Productivity Center for Replication server.

Example 3-11 repcli.properties

server=SSCTCP42-T.windows.ssclab-lj-si.net
port=9560

80 Tivoli Storage Productivity Center for Replication for Open Systems

 Important: The repcli.properties file in the client images includes the Tivoli Storage
Productivity Center for Replication server host name and port number. You do not need
to modify or edit this information. It is recommended that you configure the DNS on the
system (this can be done by editing the hosts file) instead of modifying these files.

In our example, we modify the properties file because the DNS is not configured.

5. Edit the tpcrcli-auth.properties file to include your Tivoli Storage Productivity Center
for Replication user name and password, as shown in Example 3-12. This properties file
must be placed into the tpcr-cli subdirectory, which must be created in your home user
directory, as shown in Figure 3-19. Tivoli Storage Productivity Center for Replication
accesses this file only if it is in that specific subdirectory of your home user directory. In
Example 3-12, we use Administrator home directory, which is C:\Users\Administrator.

Example 3-12 tpcrcli-auth.properties

password=myPassword
username=myUsername

Figure 3-19 tpcr-cli folder in home directory

6. After you change the properties files, verify that CSMCLI works by starting it through a
command prompt or by clicking csmcli.bat from the directory where it is copied, as shown
in Figure 3-20 on page 82.

Chapter 3. General administration and high availability 81

 Figure 3-20 Start csmcli.bat

7. The CLI window opens and you can start using CLI commands, as shown in Figure 3-21.

Figure 3-21 Tivoli Storage Productivity Center for Replication CLI

3.3.4 CLI automation

By using Tivoli Storage Productivity Center for Replication CLI, scripting is the most common
way to automate copy services management. As described in 3.3, “CLI Overview” on
page 73, you can automate the following related tasks:
򐂰 Sessions and copy sets
򐂰 Storage systems and connections
򐂰 Management servers
򐂰 Security

In the following examples, we show you how to start the CLI commands with the -script
parameter, which points to a script file that contains the actual CLI commands. We start the
script by starting csmcli.bat procedure from command prompt where we specify the name of
the script file. If the script file is in the same directory that the csmcli.bat file is in, you specify
the script file name.

82 Tivoli Storage Productivity Center for Replication for Open Systems

If you use a different directory structure for the script file from the directory where the
csmcli.bat file is in, you must specify the fully qualified directory structure where the script
file is in. Example 3-13 shows the invocation of a script file where the script file is in the same
directory that the csmcli.bat file is in.

We also set up the tpcrcli-auth.properties file to include Tivoli Storage Productivity Center
for Replication user name and password, as shown in Example 3-12 on page 81. This
properties file must be placed into the tpcr-cli subdirectory, which must be created in your
home user directory (as shown in Figure 3-19 on page 81). Tivoli Storage Productivity Center
for Replication access this file only if it is in that specific subdirectory of your home user
directory. In our example, we use user tpcadmin and home directory, which is
C:\Users\tpcadmin.

Note: We recommend the use of the setoutput command to modify the script output. The
CLI setoutput command formats the output with a delimiter, which can be a comma by
default, .xml format, or tabular format that uses commas as delimiters between columns
and stanza, which specifies that the output is displayed as one keyword-value pair per line.
The format options that are specified by using the setoutput command apply to all
commands in the script. You can use any format that meets your requirements. If you do
not run the setoutput command, the output displays in the default output format.

Example 3-13 shows you the invocation of a script file for the lsdevice command to display a
list of storage systems.

Example 3-13 Starting CLI script

C:\Program Files\IBM\TPC\cli>csmcli -script lsdevice.txt
Tivoli Storage Productivity Center for Replication Command Line Interface (CLI)
Copyright 2007, 2012 IBM Corporation
Version: 5.2.0
Build: 20130719-0641
Server: SSCTCP42-T.windows.ssclab-lj-si.net Port: 9560
Authentication file: C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties

Device ID Connection Type Device Type Local Server Connection

========================================================================
SVC:CLUSTER:SVC2PROD Direct SVC Connected
SVC:CLUSTER:SVC8 Direct SVC Connected

If you must start FlashCopy, for example, the script that is shown in Example 3-14 creates
FlashCopy relationships for all FlashCopy volume pairs that are included in the session.

Example 3-14 FlashCopy script

# Create FlashCopy relation ship
# ------------------------------
lssess -l -fmt stanza 'SVC8 FC'
cmdsess -quiet -action flash 'SVC8 FC'
lssess -l -fmt stanza 'SVC8 FC'
# -------- end of script --------------

Chapter 3. General administration and high availability 83

 The output of the script is shown in Example 3-15.

Example 3-15 FlashCopy script output

C:\Program Files\IBM\TPC\cli>csmcli -script flashcopy.txt
Tivoli Storage Productivity Center for Replication Command Line Interface (CLI)
Copyright 2007, 2012 IBM Corporation
Version: 5.2.0
Build: 20130719-0641
Server: SSCTCP42-T.windows.ssclab-lj-si.net Port: 9560
Authentication file: C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties

Name SVC8 FC
Status Warning
State Prepared
Copy Type FlashCopy
Recoverable No
Copying No
Copy Sets 1
Error No
IWNR1026I [Aug 8, 2013 8:08:52 AM] The Flash command in the SVC8 FC session
completed.
Name SVC8 FC
Status Normal
State Target Available
Copy Type FlashCopy
Recoverable Yes
Copying Yes
Copy Sets 1
Error No

C:\Program Files\IBM\TPC\cli>

After the Flash command finishes, the FlashCopy target is available and the session status
changes to Normal. FlashCopy is created by using the CLI script and you can check the
status in Tivoli Storage Productivity Center for Replication GUI, as shown in Figure 3-22.

Figure 3-22 FlashCopy status in Tivoli Storage Productivity Center for Replication GUI

If you intend to add a certain set of copy sets to a session, it is more convenient to use the CLI
instead going through all the GUI panels. With two Copy Sets, a script can look as shown in
Example 3-16 on page 85.

84 Tivoli Storage Productivity Center for Replication for Open Systems

Example 3-16 CLI - Adding copy sets
#
# Add copy sets to Metro Mirror session
# -----------------------------------------
setoutput -fmt stanza
lssess -l
mkcpset -h1 SVC:vol:SVC8:37 -h2 SVC:vol:SVC2PROD:223 SVC8-SVC2_MM
mkcpset -h1 SVC:vol:SVC8:38 -h2 SVC:vol:SVC2PROD:224 SVC8-SVC2_MM
lspair -l -cpset SVC:vol:TPC51_SVC8_1000 SVC8-SVC2_MM
lssess -l
# ----------------------------- end of script -------------------------------

The result of the script in Example 3-16 is shown in Example 3-17.

Example 3-17 Adding Copy Sets in CLI

C:\Program Files\IBM\TPC\cli>csmcli -script addcopyset1.txt
Tivoli Storage Productivity Center for Replication Command Line Interface (CLI)
Copyright 2007, 2012 IBM Corporation
Version: 5.2.0
Build: 20130719-0641
Server: SSCTCP42-T.windows.ssclab-lj-si.net Port: 9560
Authentication file: C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties

Name SVC8-SVC2_MM
Status Inactive
State Defined
Copy Type Metro Mirror Failover/Failback
Recoverable No
Copying No
Copy Sets 0
Error No

IWNR2001I [Aug 8, 2013 9:17:16 AM] The pair was created in session SVC8-SVC2_MM
for copy set with a copy set ID of SVC:VOL:SVC8:37
, with a source volume ID of SVC:VOL:SVC8:37(TPC51_SVC8_1000), and a target volume
ID of SVC:VOL:SVC2PROD:223(TPC51_SVC2_1000).

IWNR2001I [Aug 8, 2013 9:17:18 AM] The pair was created in session SVC8-SVC2_MM
for copy set with a copy set ID of SVC:VOL:SVC8:38
, with a source volume ID of SVC:VOL:SVC8:38(TPC51_SVC8_2000), and a target volume
ID of SVC:VOL:SVC2PROD:224(TPC51_SVC2_2000).

Name SVC8-SVC2_MM
Status Inactive
State Defined
Copy Type Metro Mirror Failover/Failback
Recoverable No
Copying No
Copy Sets 2
Error No

C:\Program Files\IBM\TPC\cli>

Chapter 3. General administration and high availability 85

 Note: For more information about and the complete list and description of CLI commands,
see IBM Tivoli Storage Productivity Center Version 5.2 Command-Line Interface
Reference, SC27-4089.

Example 3-18 shows you how you can make a general-purpose script run an action on the
selected session. This script helps you to automate actions on your defined sessions.

Example 3-18 Tivoli Storage Productivity Center for Replication action run script
@ECHO OFF
@echo ********************************************************
@echo ** TPC-R: ACTION EXECUTION SCRIPT **
@echo ********************************************************

set Sess=%1
set CMD=%2
IF "%~1" == "" GOTO syntax
IF "%~2" == "" GOTO syntax
SET /P yesno=Do you want to issue %CMD% for the session %Sess%? [Y/N]:
IF "%yesno%"=="y" GOTO start
IF "%yesno%"=="Y" (GOTO inizio) ELSE (GOTO Cancel)

:start
@echo.
FOR /F "tokens=1-30 delims=," %%i in ('csmcli -noinfo lssess -fmt delim -hdr off
%Sess%') do (
set sn=%%i
set st=%%j
set ss=%%k)
IF "%sn%"=="%Sess%" GOTO startaction
GOTO error

:startaction
@echo -----------INITIAL STATUS------------
echo Session name: %sn%
echo Status: %st%
echo State: %ss%
@echo -------------------------------------
FOR /F "tokens=1-30 delims=," %%i in ('csmcli -noinfo lssessactions -fmt delim
-hdr off %Sess%') do (
set ac=%%i
set de=%%j
IF %%i==%CMD% (
echo.
echo Executing %CMD%.....
call csmcli -noinfo cmdsess -quiet -action %CMD% %Sess%
GOTO run
) ELSE rem
)
GOTO error

:run
FOR /F "tokens=1-30 delims=," %%i in ('csmcli -noinfo lssess -fmt delim -hdr off
%Sess%') do (

86 Tivoli Storage Productivity Center for Replication for Open Systems

set sn=%%i
set st=%%j
set ss=%%k)
@echo.
@echo -----------FINAL STATUS--------------
echo Session name: %sn%
echo Status: %st%
echo State: %ss%
@echo -------------------------------------
@echo.
@echo Action %CMD% completed
GOTO end

:cancel
@echo.
@echo Action %CMD% cancelled
GOTO end

:syntax
@echo.
@echo Syntax error - use "TPCRscript.bat <session> <action>"
GOTO end

:error
@echo.
@echo WARNING: Action %CMD% not allowed
GOTO end

:end
@echo.
@echo Script execution terminated

Run the following command to start the script:

TPCRscript.bat session_name action

Example 3-19 shows you the output of the script where suspend action is issued for a
session.

Example 3-19 Output of TPCRscript.bat

C:\Program Files\IBM\TPC\cli>TPCRscript.bat SVC8-SVC2_MM suspend
********************************************************
** TPC-R: ACTION EXECUTION SCRIPT **
********************************************************
Do you want to issue suspend for the session SVC8-SVC2_MM? [Y/N]:y
-----------INITIAL STATUS------------
Session name: SVC8-SVC2_MM
Status: Normal
State: Prepared
-------------------------------------
Executing suspend.....
IWNR1026I [Aug 12, 2013 8:24:55 PM] The Suspend command in the SVC8-SVC2_MM
session completed.
-----------FINAL STATUS--------------
Session name: SVC8-SVC2_MM

Chapter 3. General administration and high availability 87

 Status: Severe
State: Suspended
-------------------------------------
Action suspend completed
Script execution terminated

3.4 Tivoli Storage Productivity Center for Replication

interaction with Tivoli Storage Productivity Center
Because Tivoli Storage Productivity Center for Replication is a part of the Tivoli Storage
Productivity Center, there is an interaction between them.

Tivoli Storage Productivity Center is used as a monitoring tool and it monitors Tivoli Storage
Productivity Center for Replication alerts. These alerts are defined in Tivoli Storage
Productivity Center and they are enabled by default. This means that the Tivoli Storage
Productivity Center monitors your replication and shows you different replication alerts that
are triggered by specific conditions. Each condition has a related error message identifier that
is displayed when it is detected. Table 3-2 shows the triggering conditions, an explanation,
and related error messages.

Table 3-2 Tivoli Storage Productivity Center for Replication Triggering Conditions
Triggering condition Explanation Related error message

Replication Session An alert is generated if a ALR4339W

Change replication session changes to
the following states:
򐂰 Terminating
򐂰 Target Available
򐂰 Suspended, Suspended
H2H3, Suspended H1H3
򐂰 Recovering
򐂰 Preparing
򐂰 Prepared
򐂰 Flashing
򐂰 Defined
An alert is generated if the
following conditions are
detected for a role pair:
򐂰 The role pair in a replication
session passed the
Recovery Point Objective
(RPO) warning threshold.
򐂰 The role pair in a replication
session passed the RPO
severe threshold.

Replication Suspending The state of a replication ALR4339W

Event Notification session changed to
suspending.

88 Tivoli Storage Productivity Center for Replication for Open Systems

 Triggering condition Explanation Related error message

Replication An alert is generated when the ALR4339W

Communication Failure following communication errors
are detected:
򐂰 The Replication standby
server encountered
communication errors with
the Active server.
򐂰 The Replication server
timed out when attempting
to communicate with the
storage system.
򐂰 The Replication server
encountered
communication errors with
the storage system.
򐂰 The Replication active
server stopped
communicating with the
standby server.

Replication An alert is generated when the ALR4339W

Management Server replication HA connection
State Change changes to the following states:
򐂰 Unknown
򐂰 Synchronized
򐂰 Synchronization Pending
򐂰 Disconnected
򐂰 Disconnected Consistent

Replication An alert is generated when the ALR4339W

Configuration Change following replication
configuration changes are
detected:
򐂰 One or more path
definitions were added or
removed.
򐂰 One or more copy sets
were added to a session.
򐂰 One or more copy sets
were deleted from a
session.

Note: The error message identifiers help you to locate any other information about the
error messages that are related to triggering conditions. You can check the information in
the Messages section of the IBM Tivoli Storage Productivity Center Information Center or
the IBM Tivoli Storage Productivity Center Messages Guide, SC27-4061.

If you want to disable the alerts, you can log in to Tivoli Storage Productivity Center
stand-alone GUI and in the navigation tree, click Replication Manager → Alerting →
Replication Alerts and select the alert that you want to disable. This action opens an alert
panel in which the alert details are shown. In the panel, you clear the Enabled option (as
shown in Figure 3-23 on page 90) and then click Save. Alert is disabled and it does not
appear in Alerts.

Chapter 3. General administration and high availability 89

Figure 3-23 Enabling Tivoli Storage Productivity Center for Replication alerts

In the same panel, you define triggered actions to occur as a result of the alert. You can
define the following notifications or triggered actions:
򐂰 SNMP Trap
򐂰 Tivoli Enterprise Console / OMNIbus Event
򐂰 Login Notification
򐂰 Windows Event Log, UNIX Syslog
򐂰 Run Script
򐂰 Email

When the alerts are enabled, they are shown in Tivoli Storage Productivity Center
stand-alone GUI, as shown in Figure 3-24 on page 91.

90 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 3-24 Tivoli Storage Productivity Center for Replication Alerts in Tivoli Storage Productivity Center stand-alone GUI

The alerts are also shown in the Tivoli Storage Productivity Center web-based GUI. When
you log on to the web-based GUI, click Home and select Alerts, as shown in Figure 3-25.

Figure 3-25 Tivoli Storage Productivity Center web-based GUI

Chapter 3. General administration and high availability 91

 As shown in Figure 3-26, the Alerts panel is where you see all of the alerts that are managed
by Tivoli Storage Productivity Center. To view replication alerts, click the icon on the graph
and you see all replication alerts.

Figure 3-26 Tivoli Storage Productivity Center for Replication alerts

To explore an alert, click the resource in Internal Resource column, as shown in Figure 3-26.
If the resource is a storage system, click the hyperlink and Tivoli Storage Productivity Center
for Replication GUI opens and the storage system details are displayed, as shown in
Figure 3-27. If the user that is using the Tivoli Storage Productivity Center web-based GUI
does not have access to Tivoli Storage Productivity Center for Replication, the Tivoli Storage
Productivity Center for Replication login window opens. Enter a user name and password of a
user who is authorized to use Tivoli Storage Productivity Center for Replication and the
storage system details panel opens, as shown in Figure 3-27. For more information about the
user access control, see 3.5.3, “Managing user access” on page 95.

Figure 3-27 Storage System Details in Tivoli Storage Productivity Center for Replication GUI

92 Tivoli Storage Productivity Center for Replication for Open Systems

 If the internal resource is not shown or if it is a session name, double-click a new resource in
the Internal Resource column (as shown in Figure 3-26 on page 141) and in a new window
you see the details about the alert that are related to that internal resource, as shown in
Figure 3-28.

Figure 3-28 Alert information

3.5 Tivoli Storage Productivity Center for Replication security

and user administration
In this section, we describe the role-based security model of Tivoli Storage Productivity
Center for Replication and how to add, modify, and remove user access to the application.

Tivoli Storage Productivity Center for Replication does not maintain a directory of user names
and passwords. Instead, the application uses the operating system repository or a
Lightweight Directory Access Protocol (LDAP) repository for user authentication.

The operating system repository is created by default during the installation of Tivoli Storage
Productivity Center.

For more information about the operating system and LDAP repositories, see the topic about
changing the user authentication configuration in the IBM Tivoli Storage Productivity Center
User's Guide, SC27-4060.

If you choose to use LDAP authentication, you must install the LDAP repository after you
install Tivoli Storage Productivity Center.

You can use the Tivoli Storage Productivity Center for Replication GUI or CLI to assign the
users and groups that are defined in the user repository to a user role. The roles are
predefined in Tivoli Storage Productivity Center for Replication and determine the
authorization level for individual users or all users who are in a group.

Note: To log on to Tivoli Storage Productivity Center for Replication, the user must have an
assigned user role or must belong to a group with an assigned role.

Chapter 3. General administration and high availability 93

3.5.1 Adding Tivoli Storage Productivity Center users and groups to Tivoli
Storage Productivity Center for Replication
By default, the common user that was defined during the installation of Tivoli Storage
Productivity Center and the user tpcFileRegistryUser are granted access to Tivoli Storage
Productivity Center for Replication and assigned to the Administrator role.

The user tpcFileRegistryUser is used only for recovery purposes. For example, if you
accidentally delete the repository that you are using for authentication, you can access Tivoli
Storage Productivity Center and Tivoli Storage Productivity Center for Replication by using
the user tpcFileRegistryUser.

The password for the user tpcFileRegistryUser is the same as the password that was
entered for the common user during the installation of Tivoli Storage Productivity Center.

To ensure smooth integration of Tivoli Storage Productivity Center with Tivoli Storage
Productivity Center for Replication, complete the following tasks:
򐂰 Add all Tivoli Storage Productivity Center users and groups (other than those that are
assigned by default) to Tivoli Storage Productivity Center for Replication. For example, if
you added a TPCSuperuser group to Tivoli Storage Productivity Center for LDAP
authentication, add that group to Tivoli Storage Productivity Center for Replication as well.
򐂰 Use the same user or group to log on to both applications.

You can add users and groups to Tivoli Storage Productivity Center for Replication by using
the GUI or the CLI.

3.5.2 Tivoli Storage Productivity Center for Replication role-based access

control
The following roles are defined in Tivoli Storage Productivity Center for Replication:
򐂰 Administrator
Administrators have unrestricted access to all features and functions in Tivoli Storage
Productivity Center for Replications. They can manage all replication-related activities and
sessions.
Administrators also manage access control and can assign users and groups to the
Administrator, Monitor, or Operator role. They can manage all sessions and perform all
actions that are associated with Tivoli Storage Productivity Center for Replication.
򐂰 Operator
Operators can manage specific sessions as determined by a user in the Administrator
role. Operators can issue commands only for sessions that they own.
The volumes that are in a session that is assigned to one user cannot be added to another
session that is assigned to a different user.
򐂰 Monitor
Monitors can view information in the Tivoli Storage Productivity Center for Replication;
however, they cannot modify or perform any commands or actions.

94 Tivoli Storage Productivity Center for Replication for Open Systems

 If a user is assigned to one role as an individual and a different role as a member of a group,
the role with the highest level of authorization is granted to the user. For example, if a user
belongs to a group that is assigned the Administrator role and belongs to a group that is
assigned a Monitor role, the user is granted the authorization of the Administrator role.

For more information about roles and how to assign a role to a group, see the topic about
Tivoli Storage Productivity Center for Replication security in the IBM Tivoli Storage
Productivity Center User's Guide, SC27-4060.

3.5.3 Managing user access

To manage user access by using the Tivoli Storage Productivity Center for Replication GUI,
select Administration in the navigation tree. The Administration page is displayed, as shown
in Figure 3-29. This page lists all of the users and groups that were granted access to Tivoli
Storage Productivity Center for Replication.

Figure 3-29 Administration page

You can add, modify, or remove user access from this page, as described in the following
sections.

Granting access to a user role

Complete the following steps to add a user or group to a user role:
1. On the Administration page, click Add Access, as shown in Figure 3-30 on page 96.
The Add Access wizard opens.

Chapter 3. General administration and high availability 95

 Figure 3-30 Adding a user or group to a role

2. On the Welcome page of the wizard, enter the user or group name for which you want to
add access and the number of names that you want to be displayed. You can enter a
number in the range of 1 - 100. The default is 50.
If you want to search for all users, enter an asterisk (*) in the Users or group names field.
If you want to search for users that contain certain characters, you can use the asterisk as
a filter, as shown in Figure 3-31. In this example, only users or groups that contain the
characters db2 are displayed.

Figure 3-31 Search for the user or group to assign to a role

96 Tivoli Storage Productivity Center for Replication for Open Systems

3. On the Select Users and Groups page of the wizard, select the user or group for which you
want to grant access, as shown in Figure 3-32. Only those users or groups with names
that contain the characters db2 are displayed. You can select multiple users or groups.

Figure 3-32 Select the user or group to assign to a role

4. On the Select Access Level page of the wizard, click the role that you want to assign to the
user or group. In Figure 3-33, the Operator role is selected for the group DB2USERS and
the sessions that can be managed by the users in that group are selected.

Figure 3-33 Select the role that you want to assign

Chapter 3. General administration and high availability 97

 5. On the Confirm page of the wizard, review your selections. Click Back if you want to make
other changes or click Next to continue.
6. When you are prompted, click Finish to complete the wizard. The user or group and its
role are displayed on the Administration page, as shown in Figure 3-34.

Figure 3-34 Administrator page with new DB2USERS group added

3.5.4 Modifying access to a user role

You can modify the access that is assigned to a user or group. For example, you can reassign
a user who is in the Operator role to the Administrator role. You also can add or remove
sessions for a user who is assigned to the Operator role.

Complete the following steps to change the role for a user or group:
1. On the Administration page, click the user or group that you want to modify, click
View/Modify Access in the Select Action list, and then click Go, as shown in Figure 3-35
on page 99.
The View/Modify Access page opens.

98 Tivoli Storage Productivity Center for Replication for Open Systems

Figure 3-35 Modify a user or group to a role

2. On the View/Modify Access page, click a role if you want to change the user role. If you
want to change the sessions that are assigned to a user in the Operator role, select or
clear the applicable sessions.
In Figure 3-36, the group DB2USERS is changed from the Operator role to the
Administrator role.

Figure 3-36 Modify the access for the user or group

Chapter 3. General administration and high availability 99

 3. Click OK. The role for the DB2USERS group changes from Operator to Administrator on
the Administration page, as shown in Figure 3-37.

Figure 3-37 Administration panel

3.5.5 Removing access to a user role

To remove a user or group from a role, on the Administration page, click the user or group that
you want to remove, click Remove Access in the Select Action list, and then click Go.

The user or group is removed from the list of users and roles on the Administration page.
When you remove access, the user or users in a group cannot access the Tivoli Storage
Productivity Center for Replication GUI or run commands from the command line.

3.6 Tivoli Storage Productivity Center for Replication advanced

tools
Advanced tools are useful utilities and settings that assist you with your work in Tivoli Storage
Productivity Center for Replication. By using advanced tools, you can package log files, set
the browser refresh rate, and enable or disable the Metro Mirror heartbeat feature.

To manage advanced tools, select Advanced Tools in the navigation tree of the Tivoli
Storage Productivity Center for Replication GUI. The Advanced Tools page opens, as shown
in Figure 3-38 on page 101.

100 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 3-38 Advanced Tools page

You can configure and use the utilities and settings in this page, as described in the following
sections.

3.6.1 Packaging log files

Tivoli Storage Productivity Center includes a utility that packages the log files that are created
by the application. By using this utility, you can collect all log files in one location for diagnostic
purposes. For example, you might be asked to package these files and send them to IBM
Software Support.

Complete the following steps to create a log file package:

1. On the Advanced Tools page, click Create under Package Log Files. When the log
package is created, the package file name and location on the Tivoli Storage Productivity
Center for Replication management server is displayed as a link, as shown in Figure 3-39
on page 102.

Chapter 3. General administration and high availability 101

 Figure 3-39 Link to the log package.jar file

2. Click the link to download the log package to the server on which the web browser is
running.

Note: If you want to download log packages that were created previously, click Display PE
Packages.

3.6.2 Setting the auto refresh rate for the browser

On the Advanced Tools page, you can define the rate in seconds in which the content in the
web browser is refreshed. You can enter a number 5 - 3600; the default is 30, as shown in
Figure 3-39.

3.6.3 Managing the Metro Mirror heartbeat

When the Metro Mirror heartbeat is enabled, the Tivoli Storage Productivity Center for
Replication management server sends a signal to all connected ESS800, DS6000, and
DS8000 storage systems on which the server is managing replication relationships.

If the connection is lost to one storage system, the heartbeat signal is stopped to the
remaining storage systems. The volumes on the other storage systems are also frozen to
maintain consistency across the storage systems.

If the connection is lost to one of the storage systems, the storage system responds by
freezing all logical storage subsystem (LSS) pairings that are managed by the management
server. This process of freezing LSS pairings across the storage systems helps to ensure
consistency across the storage systems.

The Metro Mirror heartbeat is available for Metro Mirror sessions that do not have HyperSwap
enabled.

102 Tivoli Storage Productivity Center for Replication for Open Systems
 When you are determining whether to use the Metro Mirror heartbeat, analyze your business
needs. If you disable the Metro Mirror heartbeat, data might become inconsistent if the
management server is down or connection to a storage system is lost. If you enable the Metro
Mirror heartbeat and a freeze occurs, your applications cannot perform write operations until
the freeze timeout value for the storage system passes.

For more information about the Metro Mirror heartbeat, see the topic about using the Metro
Mirror heartbeat in the IBM Tivoli Storage Productivity Center User's Guide, SC27-4060.

To enable or disable the Metro Mirror Heartbeat, on the Advanced Tools page, click Enable
Heartbeat or Disable Heartbeat.

By default, the Metro Mirror Heartbeat is disabled, as shown in Figure 3-40.

Figure 3-40 Enable or disable the Metro Mirror heartbeat

3.7 Tivoli Storage Productivity Center for Replication Console

Tivoli Storage Productivity Center for Replication provides a detailed log of user and system
activity. This log is called the Tivoli Storage Productivity Center for Replication Console.

The Tivoli Storage Productivity Center for Replication Console detects dependent messages
and groups them as so-called child/children messages under the root message for the logged
event, which significantly improves the readability of the log. The console also provides a
hyperlink-based help system for the various messages.

You can start the console by clicking Console from the navigation tree area of the Tivoli
Storage Productivity Center for Replication GUI, as shown in Figure 3-41 on page 104.

Chapter 3. General administration and high availability 103

Figure 3-41 Opening Console from navigation tree

You also can click Open Console in the message lines, which is in the upper section of the
Work Area after you performed specific actions in Tivoli Storage Productivity Center for
Replication, as shown in Figure 3-42.

Figure 3-42 Example of Open Console hyperlink

104 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 3-43 shows the Tivoli Storage Productivity Center for Replication Console window with
various roots and a pointer to child messages.

Figure 3-43 Tivoli Storage Productivity Center for Replication Console window

The console lists the message IDs of the messages as hyperlinks. Clicking these hyperlinks
takes you to the associated help panels, as shown in Figure 3-44 on page 106.

Chapter 3. General administration and high availability 105

Figure 3-44 Help panel

If you created a log package and must download it later, the console shows you the log
package destinations as hyperlinks. By clicking these hyperlinks, the package file is saved.

3.8 Tivoli Storage Productivity Center for Replication High

Availability
Tivoli Storage Productivity Center for Replication offers support for creating a more resilient,
highly available Tivoli Storage Productivity Center for Replication environment by using a
standby server concept.

In addition to your active Tivoli Storage Productivity Center for Replication server, you can
install a second Tivoli Storage Productivity Center for Replication server into your
infrastructure (for example, at your remote site) and define it as a Tivoli Storage Productivity
Center for Replication standby server. Tivoli Storage Productivity Center for Replication then
replicates all changes of the active server’s repository to the repository of the standby server.

Note: Because the servers communicate with each other over TCP/IP network, make sure
that they are authenticated through all firewalls.

At any time, a takeover process can be started at the standby server. This takeover process
stops any relationship between active and standby server and turns the standby server into
an active Tivoli Storage Productivity Center for Replication server with the same configuration
the original server had at the time of takeover. This takeover process often occurs after the
active server fails or is down because of a disaster.

106 Tivoli Storage Productivity Center for Replication for Open Systems
 The Tivoli Storage Productivity Center for Replication standby server does not need to be on
the same operating system platform as the active Tivoli Storage Productivity Center for
Replication server. Tivoli Storage Productivity Center for Replication supports a standby
server that is running in another platform.

This section guides you through the steps to set up a Tivoli Storage Productivity Center for
Replication Server as a standby server and explains how to start a takeover process.

Figure 3-45 shows an overview of a typical two-site storage infrastructure with a high
available Tivoli Storage Productivity Center for Replication installation.

Figure 3-45 Active and standby Tivoli Storage Productivity Center for Replication servers

As Figure 3-45 shows, both servers must have IP connectivity to each other and to all storage
systems that are managed by Tivoli Storage Productivity Center for Replication.

Note: Tivoli Storage Productivity Center for Replication supports one standby server for an
active server. This is also true for a three-site environment.

3.8.1 Setting up a Tivoli Storage Productivity Center for Replication standby

server
To set up a Tivoli Storage Productivity Center for Replication standby server for your active
server, you must install the Tivoli Storage Productivity Center to the standby server. This task
also installs Tivoli Storage Productivity Center for Replication.

Chapter 3. General administration and high availability 107

 The standby server can be set up by using one of the following methods:
򐂰 Setting up a different server as the standby server
򐂰 Setting up the server you are logged in to as the standby server

Note: The standby server cannot manage sessions that are running in the active server.
Also, the standby server must be configured after you have your High Availability plan
defined. After setting a server as a standby server, you cannot use this server for any other
purpose than a Takeover.

Setting up a different server as the standby server

You set up a Tivoli Storage Productivity Center for Replication standby server by logging in to
the active server and defining a different server as a standby server.

Assume that you have an active Tivoli Storage Productivity Center for Replication server with
some sessions defined, but without a standby management server, as shown in Figure 3-46.

Figure 3-46 Active Tivoli Storage Productivity Center for Replication server with defined sessions

To define the standby Tivoli Storage Productivity Center for Replication server, click
Management Servers in the navigation tree from of your active Tivoli Storage Productivity
Center for Replication Server or click Configure in the Health Overview panel.

The Management Servers panel of your active server opens, as shown in Figure 3-47 on
page 109. You can see an entry for your server with its DNS name and the information that it
has the active role.

108 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-47 Active Tivoli Storage Productivity Center for Replication server: Management Servers panel

From the drop-down menu of the Management Servers panel, select Define Standby and
click Go, as shown in Figure 3-48.

Figure 3-48 Active Tivoli Storage Productivity Center for Replication server: Select Define Standby

Chapter 3. General administration and high availability 109

 Tivoli Storage Productivity Center for Replication now shows a panel in which you must enter
the IP address or the fully qualified DNS name of your designated Tivoli Storage Productivity
Center for Replication standby server. You also must enter a user name and a password for
the standby server, as shown in Figure 3-49. This user must be a Tivoli Storage Productivity
Center for Replication Administrator. Click OK after you enter and verify your information.

Figure 3-49 Define address and user credentials for standby

Important: Defining a Tivoli Storage Productivity Center for Replication server as a

standby server overwrites the complete database of the standby server. There is no way
within Tivoli Storage Productivity Center for Replication to recover the configuration after it
is overwritten.

Also, Tivoli Storage Productivity Center for Replication server uses TCP port 9561 for
communication with other Tivoli Storage Productivity Center for Replication servers for
high-availability purposes.

After you click OK, a confirmation message is shown that explains that you are about to
overwrite the current configuration for this management server and prompts you to confirm
that you want to continue, as shown in Figure 3-50. Click Yes.

Figure 3-50 Standby server confirmation message

110 Tivoli Storage Productivity Center for Replication for Open Systems
Tivoli Storage Productivity Center for Replication establishes communication with the
designated standby server, turns it into standby mode, and then starts to synchronize the
repository of the active server with that of the standby server. The Management Servers
status switches to a Connected status and warning, as shown in Figure 3-51, while the
repository of active Tivoli Storage Productivity Center for Replication is copied to the standby
Tivoli Storage Productivity Center of Replication server.

Figure 3-51 Status after define of standby server

After the synchronization process completes, the state turns to a Synchronized status and
you see the content of the Management Servers panel of your active server that is shown in
Figure 3-52.

Figure 3-52 Standby server is synchronized

Chapter 3. General administration and high availability 111

 The standby server Tivoli Storage Productivity Center for Replication now shows that it is
connected to the remote server, as shown in Figure 3-53.

Figure 3-53 Health Overview panel after standby synchronization

Setting up the server you are logged in to as the standby server

You can also define your standby server by logging in to the designated standby server and
set it as standby.

From the Management Servers panel, select Set this Server as Standby in the drop-down
menu and click Go, as shown in Figure 3-54 on page 113.

112 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-54 Set the current server as a Tivoli Storage Productivity Center for Replication standby server

In the next panel, you must specify the IP address or DNS name of the server for which your
current server acts as a standby server. You do not have to supply any user credentials
because you do not overwrite the configuration of the active server or damage it in any other
way.

Click Ok to define your server as standby, as shown in Figure 3-55 on page 113.

Figure 3-55 Enter the address of the active Tivoli Storage Productivity Center for Replication server

Chapter 3. General administration and high availability 113

 Important: Defining a Tivoli Storage Productivity Center for Replication server as a
standby server overwrites the complete database of the standby server. There is no way
within Tivoli Storage Productivity Center for Replication to recover the configuration after it
is overwritten.

After you click OK, a confirmation message is shown that provides a warning that you will
overwrite the current configuration for this management server and prompts you to confirm
that you want to continue, as shown in Figure 3-56. Click Yes.

Figure 3-56 Set this Server as Standby confirmation message

Tivoli Storage Productivity Center for Replication now establishes communication with the
designated active server and starts to synchronize the repository of the active server with the
standby server. The Management Servers status switches to Connected status, as shown in
Figure 3-57 on page 114, but it is still in warning because the servers are not yet
synchronized.

Figure 3-57 Warning status

114 Tivoli Storage Productivity Center for Replication for Open Systems
After the synchronization process completes, the state turns to Synchronized and you see the
content of the Management Servers panel of your active server that is shown in Figure 3-58.

Figure 3-58 Standby Server that is synchronized

The standby server is successfully defined for your active Tivoli Storage Productivity Center
for Replication server. Your active server works as before (but now t it propagates all changes
to your standby server). However, your standby server now has the following different
properties:
򐂰 Configuration of the Tivoli Storage Productivity Center for Replication standby server in
terms of Storage Systems, ESS/DS Paths, Sessions, and Copy Sets was overwritten with
the configuration of the active Tivoli Storage Productivity Center for Replication server.
򐂰 The Sessions menu item is disabled so that you cannot view or modify any Session or
Copy Set-related configurations from the standby server.
򐂰 You can view the Storage Subsystem and ESS/DS Paths configuration, but you cannot
make any changes from the standby server.
򐂰 You can access the Advanced Tools menu but you cannot alter the Heartbeat setting from
the standby server.
򐂰 You can still access the Tivoli Storage Productivity Center for Replication Console from the
standby server.

Note: User access data is not synchronized between active and standby Tivoli Storage
Productivity Center for Replication servers.

Setting up standby server by using CLI

You can also use the Tivoli Storage Productivity Center for Replication CLI to define a standby
server for your active server or to define your current server as a standby server to a different
server.

Chapter 3. General administration and high availability 115

 To define a standby server for your active server, open a CLI command window on your active
server and run the setstdby CLI command, as described in the following steps:
1. Run csmcli.bat from your default Tivoli Storage Productivity Center for Replication
installation directory TPC_Install\Program Files\IBM\TPC\cli. The command opens a
CLI window. If you did not set up the CLI properties file, the CLI prompts you to enter a
username and password for logging on to the server. On AIX and Linux servers, you must
run the csmcli.sh script from the default Tivoli Storage Productivity Center for Replication
installation directory /opt/IBM/TPC.
2. Run the lshaservers command to verify that your active server is not already connected
to a standby server, as shown in Example 3-20.

Example 3-20 List HA servers

csmcli> lshaservers
Server Role Status Port
==========================================================
SSCTCP42-T.windows.ssclab-lj-si.net ACTIVE No Standby 9561
csmcli>

3. Run the setstdby command the set the standby server. Through the CLI, you are informed
that this operation overwrites the contents of the standby server database, and you are
prompted to confirm that you want to continue, as shown in Example 3-21.

Example 3-21 Adding standby server

csmcli> setstdby -password 12345678 -server 172.31.149.2 -username Administrator
IWNR3111W [Aug 15, 2013 12:56:01 AM] This command will define another management
server as a standby for this server. This will overwrite the configuration of the
specified standby. Do you want to continue? [y/n]:y
IWNR3020I [Aug 15, 2013 12:56:05 AM] Connection to the active high-availability
server at 172.31.83.171 making the server IICTPCRT1-PRI.windows.ssclab-lj-si.net a
standby was successful.
csmcli>

4. Run the lshaserves command again to confirm that your active server now has a standby
server, as shown in Example 3-22.

Example 3-22 New standby server

csmcli> lshaservers
Server Role Status Port
=============================================================
SSCTCP42-T.windows.ssclab-lj-si.net ACTIVE Synchronized 9561
IICTPCRT1-PRI STANDBY Synchronized 9561
csmcli>

The standby server is successfully defined for your active Tivoli Storage Productivity Center
for Replication server.

3.8.2 Takeover
If your active Tivoli Storage Productivity Center for Replication server fails (or if there is a
planned failover), you must perform a takeover of the active server role on your standby Tivoli
Storage Productivity Center for Replication server.

116 Tivoli Storage Productivity Center for Replication for Open Systems
 The takeover action is a manual process, which can be started through the GUI or the CLI on
the Tivoli Storage Productivity Center for Replication standby server.

After you perform the manual takeover on the standby server, the synchronization of
repository changes stops and the Tivoli Storage Productivity Center for Replication standby
server becomes an active server with the same configuration as the original active server.

This is the case even when the original active server is still running. In this case, you have two
active Tivoli Storage Productivity Center for Replication servers with identical configurations
in your environment. You can manipulate your copy services configurations from both servers,
although changes in the Tivoli Storage Productivity Center for Replication databases are no
longer synchronized between the two active servers.

This can lead to inconsistencies in your overall configuration, which can damage your
environment. Therefore, we do not recommend that you have two active Tivoli Storage
Productivity Center for Replication servers.

Important: Before you attempt a Tivoli Storage Productivity Center for Replication
takeover, we recommend that you always shut down the active Tivoli Storage Productivity
Center for Replication server or stop the replication server.

You can start a takeover only from the standby server. In a planned situation (for example, for
maintenance purposes), we recommend that you first shut down the Tivoli Storage
Productivity Center for Replication or stop the replication server by running the
stopTPCreplication.bat command.

After you stop the active Tivoli Storage Productivity Center for Replication server, the standby
server is in Disconnected Consistent status, as shown in Figure 3-59.

Figure 3-59 Standby server status: Disconnected Consistent

You can see that all storage systems that are connected as the standby server received the
configuration of the storage systems via the repository synchronization process from the
active server.

Chapter 3. General administration and high availability 117

 The Sessions hyperlink in the navigation tree area is grayed out (as shown in Figure 3-59)
because the Tivoli Storage Productivity Center for Replication server is still the standby
server.

Click Management Servers, which opens the Management Servers panel of your standby
server, as shown in Figure 3-60.

Figure 3-60 Management Servers panel on Standby server

You now see a list of two Tivoli Storage Productivity Center for Replication servers with active
and standby roles.

The status of both management servers is Disconnected Consistent from the point of view of
the standby server. This means that the standby server cannot communicate with its active
server, but it has a consistent database and can take over the role of the active server.

In the drop-down menu, select Takeover and click Go (as shown in Figure 3-61 on page 119)
to start the takeover process.

118 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-61 Standby server: Takeover

You also have the opportunity to attempt to reconnect to your active server before you decide
that a takeover is necessary. The active server is down, so you can omit this step.

You first see a confirmation message that warns you that if the original active server is still up,
you have two active Tivoli Storage Productivity Center for Replication servers with identical
configurations in your environment, as shown in Figure 3-62.

Figure 3-62 Standby server: Confirm takeover

Because you shut down your original active server, click Yes to continue.

Tivoli Storage Productivity Center for Replication changes the role of your standby server to
an active server, as shown in Figure 3-63 on page 120.

Chapter 3. General administration and high availability 119

 Figure 3-63 Takeover action

After few seconds, the Management Servers panel that is shown in Figure 3-64 opens.

Figure 3-64 Takeover complete

120 Tivoli Storage Productivity Center for Replication for Open Systems
 Your standby server is now an active Tivoli Storage Productivity Center for Replication server.
The Sessions menu item in the Navigation Area is now active. You can manipulate your
sessions from the activated standby server.

Click Sessions in the navigation area. The Sessions Overview panel opens in which a list of
the sessions that were originally configured on the previous active Tivoli Storage Productivity
Center for Replication server are shown, as shown in Figure 3-65.

Figure 3-65 Sessions on the new active TPC-R server

You can also perform the takeover process by using the CLI and the hatakeover command
that is run by the standby server, as shown in Example 3-23.

Example 3-23 Takeover command in CLI

csmcli> hatakeover
IWNR3114W [Aug 15, 2013 2:20:27 AM] This command will make this standby management
server an active management server. Both management servers will be active with
identical configurations. Do you want to continue? [y/n]:y
IWNR3063I [Aug 15, 2013 2:20:33 AM] Successfully issued the takeover to the
standby server SSCTCP42-T.windows.ssclab-lj-si.net with the active HA server
IICTPCRT1-PRI.
csmcli> lshaservers
Server Role Status Port
==========================================================
SSCTCP42-T.windows.ssclab-lj-si.net ACTIVE No Standby 9561
csmcli>

Tivoli Storage Productivity Center for Replication does not offer a failback function. Complete
the following steps to return to your original active server:
1. Start your recovered original Tivoli Storage Productivity Center for Replication server.
2. On the original active Tivoli Storage Productivity Center for Replication GUI, select
Management Servers and then select Remove Standby from Select Action drop-down
menu.

Chapter 3. General administration and high availability 121

 3. After the standby server is removed, select Set this Server as Standby from the Select
Action drop-down menu. Tivoli Storage Productivity Center for Replication GUI prompts
you to specify the name or IP address of the Active Server.
4. Wait until both servers reach the Synchronized status.
5. Perform a takeover on this Tivoli Storage Productivity Center for Replication server after
synchronization completes. You have two active servers during this part of the process.
6. On the original standby server, remove the standby server by clicking Remove Standby
from the drop-down menu
7. Set your original standby server as a standby server to the original active server.

3.8.3 Best practices

In this section, we describe best practices for configuring and using Tivoli Storage
Productivity Center for Replication in a highly available Tivoli Storage Productivity Center for
Replication environment.

High-availability configuration
The Tivoli Storage Productivity Center for Replication high-availability configuration is highly
recommended because it provides high availability of replication management. As a best
practice, we recommend that you have the active Tivoli Storage Productivity Center for
Replication server always in primary site, while the standby server is required in disaster site.
If you have a three-site solution, the standby server is not required in the intermediate site, so
in a three-site solution, such as Metro Global Mirror, the standby server is required in the third
site.

Tivoli Storage Productivity Center for Replication does not support two standby servers. If
there is a disaster on the primary site, the standby server is in Disconnected Consistent
status and is ready to takeover. This action makes the standby server active and you can
continue to manage replication.

Accidentally removing the standby server

If you accidentally remove the standby server from the active server, you can reconnect the
standby server. The standby server is in Disconnected Consistent status. On the standby
server, you must run Reconnect action and it synchronizes the repository with your active
server.

Loss of connectivity in high-availability configuration

When you lose connectivity between the active and standby server, the servers has the
Disconnected Consistent status. When the connection is available, the communication
between the servers must be manually reconnected. To do this, select Reconnect action on
the Management Servers panel from the drop-down menu and then click Go. The server is
synchronized again, and you have high-available configuration.

122 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: Tivoli Storage Productivity Center for Replication does not automatically
resynchronize the servers if the loss of connectivity was the result of a network issue
breaking communication.

Because Tivoli Storage Productivity Center for Replication cannot determine what caused
the breakage, the server is not automatically resynchronized. The original active server
might be corrupted during the downtime. If this was the case, we do not want to wipe out
the standby, which might be the only uncorrupted version of the server. For this reason,
Tivoli Storage Productivity Center for Replication waits for a customer command that
indicates that the active server is not corrupted.

Upgrading use scenario

Upgrading Tivoli Storage Productivity Center for Replication in a high-availability configuration
requires planning and step-by-step procedures because the servers are synchronized. In this
section, we describe a procedure to upgrade the active and standby Tivoli Storage
Productivity Center for Replication server.

Complete the following steps to upgrade the servers:

1. Run the takeover command of active server on the standby server. This makes your
standby server active and ready for upgrade.
2. Upgrade the standby server.
3. Wait for the standby server to complete the upgrade installation and start. The standby
server is active server with no defined standby server.
4. Upgrade the active server.
5. If no changes were made to the configuration while the active server is upgraded,
reestablish the High Availability function from the active server to the defined standby
server by selecting Reconnect action.
6. If configuration changes were made to the standby server (server 2), synchronize the High
Availability function from the standby server to the active (server 1) by using the Define
Standby action on active server (server 1). To go to the original configuration, you must
perform a takeover, make that new standby server (server 1) as an active server, and
define its standby server, original standby server (server 2).

Note: During the initial synchronization, the current information in the repository is saved
and held until the synchronization is complete. If an error occurs during this process, the
server repository is restored to its original state before the synchronization process began.
If an error occurs during the synchronization process that causes the status to be in the
disconnected or inconsistent state, you can reconnect to a synchronized state.

3.9 Starting and stopping the Tivoli Storage Productivity

Center for Replication server
In this section, we describe how to verify that Tivoli Storage Productivity Center for
Replication components are running and how to start or stop Tivoli Storage Productivity
Center for Replication components if they must be restarted.

Scripts for starting and stopping Tivoli Storage Productivity Center for Replication
components are provided by the Tivoli Storage Productivity Center installation.

Chapter 3. General administration and high availability 123

3.9.1 Verifying the status of components
After you install Tivoli Storage Productivity Center, you can verify whether the Tivoli Storage
Productivity Center for Replication components are running. The procedure that is described
in this section can also be used if there is a problem with Tivoli Storage Productivity Center for
Replication. We also describe a procedure to start and stop Tivoli Storage Productivity Center
for Replication server.

Starting from version 5.2, Tivoli Storage Productivity Center for Replication is running as a
process in a Windows environment.

To check whether the process is running, start Task Manager on Windows, as shown in
Figure 3-66, and look for java.exe *32 processes.

Figure 3-66 Starting Windows Task Manager

To check which Java process is using Tivoli Storage Productivity Center for Replication, you
must add the Command Line column, as shown in Figure 3-67 on page 125. This column
shows details about the processes where you can see that Tivoli Storage Productivity Center
for Replication process is started, as shown in Figure 3-68 on page 125.

124 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 3-67 Selecting Command Line view

Figure 3-68 Tivoli Storage Productivity Center for Replication process running

Chapter 3. General administration and high availability 125

 On AIX and Linux servers, you can check whether the Tivoli Storage Productivity Center for
Replication components are running by running the following command:

ps -aef | grep replication

You can also check whether the Tivoli Storage Productivity Center for Replication
components are running on the Windows operating system by completing the following steps:
1. In a Windows Command Prompt, go to the directory
TPC_installation_directory\wlp\bin\ where TPC_installation_directory is the
top-level directory where you installed Tivoli Storage Productivity Center (for example,
C:\Program Files\IBM\TPC\).
2. Run the server.bat status replicationServer command, which should return a status
of running, as shown in Example 3-24.

Example 3-24 TPC-R status running

C:\Program Files\IBM\TPC\wlp\bin>server.bat status replicationServer
Server replicationServer is running.

If the Tivoli Storage Productivity Center for Replication components are not running, you see
a status as shown in Example 3-25.

Example 3-25 TPC-R status not running

C:\Program Files\IBM\TPC\wlp\bin>server.bat status replicationServer
Server replicationServer is not running.

On the AIX or Linux operating system, you run the ./server status replicationServer
command from the TPC_installation_directory/wlp/bin/ where
TPC_installation_directory is the top-level directory where you installed Tivoli Storage
Productivity Center; for example, /opt/IBM/TPC/.

You can also check whether Tivoli Storage Productivity Center of Replication server is
running by entering the address of Tivoli Storage Productivity Center for Replication server
(https://hostname:port/CSM) in a supported web browser. If you see the Tivoli Storage
Productivity Center for Replication login page, it means that all Tivoli Storage Productivity
Center for Replication components are running. Otherwise, you see the message that is
shown in Figure 3-69.

Figure 3-69 Tivoli Storage Productivity Center for Replication server is not running

126 Tivoli Storage Productivity Center for Replication for Open Systems
 On the Windows operating system, the Tivoli Storage Productivity Center of Replication
server use scheduled tasks to start the servers when the Windows computer is started again.
To view the scheduled tasks for the Device server and the Replication server on Windows,
start the Windows Task Scheduler by clicking Start → Administrative Tools → Task
Scheduler. In the Task Scheduler navigation tree, click Task Scheduler Library. The
scheduled task for the Device server is called startDevServer, and the scheduled task for the
Replication server is called startRepServer, as shown in Figure 3-70.

Figure 3-70 Tivoli Storage Productivity Center for Replication server scheduled task

3.9.2 Starting and stopping Tivoli Storage Productivity Center for Replication
To start and stop Tivoli Storage Productivity Center for Replication, you run scripts on the
server where the Tivoli Storage Productivity Center for Replication is installed. The scripts are
in the TPC_installation_directory\scripts\ directory where TPC_installation_directory
is the top-level directory where you installed Tivoli Storage Productivity Center; for example,
C:\Program Files\IBM\TPC\. The scripts folder also contains Tivoli Storage Productivity
Center scripts to start and stop Tivoli Storage Productivity Center components, which are
Data server, Device server, Storage Resource Agent, web server, and JazzSM.

To start the Tivoli Storage Productivity Center for Replication server on the Windows
operating system, enter the startTPCReplication.bat command from the scripts folder in an
administrator Windows command prompt (see Figure 3-71 on page 128), or run the script as
administrator from Windows Explorer (see Figure 3-72 on page 128).

Chapter 3. General administration and high availability 127

 Figure 3-71 Running the script from Command Prompt

Figure 3-72 Running the script from Windows Explorer

Tivoli Storage Productivity Center for Replication server starts and you can check the status
by logging in to Tivoli Storage Productivity Center for Replication.

To stop the Tivoli Storage Productivity Center for Replication server on the Windows
operating system, enter the stopTPCReplication.bat command from the scripts folder in an
administrator Windows Command Prompt, or run the script as administrator from Windows
Explore. Figure 3-73 on page 129 shows you the message when the Tivoli Storage
Productivity Center for Replication server stops.

128 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 3-73 Stopping Tivoli Storage Productivity Center for Replication

To start or stop the Tivoli Storage Productivity Center for Replication servers on the Linux or
AIX operating systems, enter the following commands in the default TPC_install_directory,
which is /opt/IBM/TPC/scripts:
򐂰 Start Tivoli Storage Productivity Center for Replication server:
/TPC_install_directory/scripts/startTPCReplication.sh
򐂰 Stop Tivoli Storage Productivity Center for Replication server
/TPC_install_directory/scripts/stopTPCReplication.sh

3.10 Using CSV files for importing and exporting sessions

In this section, we describe how to import and export a comma-separated value (CSV) file. A
CSV file includes each of the Copy Sets that you want to add to the session and Copy Sets
that are generated from existing sessions. You also see how to use a CSV file to record Copy
Sets by using a text editor or spreadsheet editor.

Note: CSV files are text files that are created in a spreadsheet program such, as Microsoft
Excel.

To manage Import and Export Sessions, you must have an Administrator or Operator role.

3.10.1 Exporting CSV files

By exporting a CSV file, you can maintain a backup copy of your copy sets; for example, if you
lose your session or upgrade to a different server. By exporting the copy sets in a session,
you can take a snapshot of your session at a particular point and save the exported file for
backup or to be used for import purposes. You export the Copy Sets from a session into a
CSV file, which you view or edit in a spreadsheet program.

Chapter 3. General administration and high availability 129

 Access for export activity is managed in the Session panel in the Navigation Area. You can
start this panel by clicking Sessions in the Navigation Area of the Tivoli Storage Productivity
Center for Replication GUI, as shown in Figure 3-74.

Figure 3-74 Tivoli Storage Center for Replication GUI

Select the session that you want to export by clicking the radio button on the left side of the
Session Name. Select Export Copy Sets in the drop down-menu and then click Go, as
shown in Figure 3-75.

Figure 3-75 Select session to Export Copy Sets

130 Tivoli Storage Productivity Center for Replication for Open Systems
The Export Copy Sets panel opens. Tivoli Storage Productivity Center for Replication creates
a CSV file that contains the Copy Sets and provides a link to download the CSV file. Click the
CSV file name link, as shown in Figure 3-76.

Figure 3-76 Export Copy Sets

You can open this file or save it by downloading it. We recommend that you open it only to
read the content. Do not edit the file now. However, if you want to edit the file, make your edits
after you save the file by using a spreadsheet program, as described in 3.10.3, “Working with
CSV files under Microsoft Excel” on page 139.

If you are using Microsoft Internet Explorer as your web browser, click Save. By using Internet
Explorer, you can choose the directory to which you save the CSV file. If you are using Mozilla
Firefox as your web browser, click Save File, as shown in Figure 3-77 on page 132. You can
choose the directory where you download your files by clicking in Mozilla Firefox menu bar
Tools → Options. You can specify the directory that you want for saving the files in the
Downloads area of the Options menu.

Chapter 3. General administration and high availability 131

 Figure 3-77 Selecting Save File option

Click Finish to close the Export Copy Set window.

3.10.2 Importing CSV files

By importing a CSV file, you can recover a backup copy of your Copy Sets; for example, if you
lose your session, or upgrade to a different server. You also can import a previous exported
session and add Copy Sets by using a spreadsheet program, such as Microsoft Excel, as
shown in 3.10.3, “Working with CSV files under Microsoft Excel” on page 139.

You can import Copy Sets from a CSV file that you previously created by using one of the
following methods:
򐂰 Import a Copy Sets in a new Session
򐂰 Import a Copy Sets in existing Session

These methods are described next.

Importing a Copy Set in a new Session

In this section, we describe the steps that are used to import the saved CSV file that contains
Copy Sets in a new session. From the Sessions panel, click Create Session to proceed, as
shown in Figure 3-78 on page 133.

132 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-78 Create Session

Select the Session Type from the drop-down menu and click Next, as shown in Figure 3-79.

Note: The Session Type should have the same Session Type defined into the previously
exported CSV file that is to be imported.

Figure 3-79 Choose Session Type panel

Complete the Session Name, Description, and Properties sections as you require.
Figure 3-80 on page 134 shows an example of how you specify this information for a
FlashCopy session. Click Next to continue.

Chapter 3. General administration and high availability 133

 Figure 3-80 Session properties

In the next panel, specify the Site Location, as shown in Figure 3-81. Select the Site Location
from the drop down-menu and then click Next.

Note: The Site Locations should be the same as defined in the previously exported
Session.

Figure 3-81 Session Site Locations

134 Tivoli Storage Productivity Center for Replication for Open Systems
Repeat this process for specifying other Locations as your session requires.

A successfully created session message is displayed. Click Launch Add Copy Set Wizard at
the bottom of the panel, as shown in Figure 3-82.

Figure 3-82 Starting Add Copy Sets Wizard

In the Add Copy Set Wizard panel, select Use a CVS file to import copy sets to use a CVS
file to import Copy Sets. You can enter a file name manually, but we recommend that you use
the browse option to avoid entering an error. Click Browse to proceed, as shown in
Figure 3-83.

Figure 3-83 Choosing CSV file to be imported

Chapter 3. General administration and high availability 135

 Select the exported or created CSV file. Click Open, as shown in Figure 3-84.

Notes: Consider the following points as you proceed:

򐂰 It is not possible to choose multiple CSV files in the same operation.
򐂰 The Copy Sets in CSV files have a specific format to address Copy Services functions,
such as FlashCopy (FC), Metro Mirror (MM), and Metro/Global Mirroring (MGM). With
the specific formats, it is not possible to import a CSV file with specific characteristics
into another file with different characteristics.
򐂰 Be sure that Copy Sets in the CSV file have the same Site Location as defined in the
Session that Copy Sets are imported to avoid errors.
򐂰 The CSV file is case-sensitive.

Figure 3-84 Opening exported Copy Set file

Click Next.

Tivoli Storage Productivity Center for Replication checks if the volumes are defined in another
session. It might show you a warning, as shown Figure 3-85 on page 137. After you click
Next, Tivoli Storage Productivity Center for Replication shows you the reason for the warning.
(This warning does not prohibit you from adding this Copy Set.)

136 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-85 Matching results warning

After clicking Next, Tivoli Storage Productivity Center for Replication shows the panel to
select the Copy Sets. It also shows the reasons for the warning message, if there is one.
Verify whether the selected Copy Set to be imported is selected and click Next, as shown in
Figure 3-86.

Figure 3-86 Selecting and Checking Copy Sets to be imported

Chapter 3. General administration and high availability 137

 Tivoli Storage Productivity Center for Replication displays the panel to confirm that you want
to add the Copy Sets. Click Next to confirm that you want to add the Copy Sets.

Click Finish to exit the wizard, as shown in Figure 3-87.

Figure 3-87 Finishing importing Copy Sets

Importing Copy Sets into an existing session

From the Session window, select the session to which you want to add the Copy Sets, then
select Add Copy Sets from the drop-down menu. Click Go, as shown in Figure 3-88.

Figure 3-88 Adding Copy Sets to existing Session

The steps to add the Copy Sets are the same as described in “Importing a Copy Set in a new
Session” on page 132.

When you are adding a Copy Sets to an existing Session with Copy Sets already active with
Status Normal and State Target Available, the Status changes to Warning, as shown in
Figure 3-89 on page 139.

138 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 3-89 Warning when Copy Sets are added to an existing active Session

Tivoli Storage Productivity Center for Replication automatically starts the copying process.
The session changes its status to Normal when the new Copy Sets finishes its initial copy
process and enters Prepared state in the MM configuration, as shown in Figure 3-90.

Figure 3-90 Session back to normal after adding Copy Sets

3.10.3 Working with CSV files under Microsoft Excel

To simplify creating and implementing sessions, you can create a session with small Copy
Sets session and export this session to be used in the future under Microsoft Excel. To open
and edit a Copy Sets Session that was saved in CSV format, you start Microsoft Excel and
open this file in the directory where you saved the file during the Export Copy Sets process.

The Copy Sets Session file name for the FC session that was exported in Figure 3-76 on
page 131 has the name FCDB2session2013-08-13-01-56-27.csv. Tivoli Storage Productivity
Center for Replication creates the exported session with the name of the session that is
appended with date and time stamp. This file name is the file name that is used when you are
importing a Copy Sets Session file.

As shown in Figure 3-91 on page 140, you can open and edit the spreadsheet to add volumes
that are related to the session that you are working with and import the session back to your
Tivoli Storage Productivity Center for Replication session, as described in 3.10.2, “Importing
CSV files” on page 132.

Chapter 3. General administration and high availability 139

 Figure 3-91 FC exported session

Figure 3-91 shows you an exported FC session, which includes the following information:
򐂰 FCDB2session is the exported session name.
򐂰 FlashCopy is the session type.
򐂰 H1 and T1 are labels that describe the Copy Set roles of the storage systems and volumes
that belong to the exported FlashCopy session. Under these labels are the storage
systems and volumes.

3.11 Backing up and restoring a repository

The Tivoli Storage Productivity Center for Replication repository contains all product data,
including data about storage systems, sessions, copy sets, paths, user administration, and
management servers. You can back up this data and use the backup file to recover from a
disaster or restore a previous configuration. As described in 3.10.1, “Exporting CSV files” on
page 129, copy sets also can be backed up and recovered by using CSV files, but this does
not cover other Tivoli Storage Productivity Center for Replication repository data.

It is recommended that you back up Tivoli Storage Productivity Center for Replication
regularly, especially in the following situations:
򐂰 After the Tivoli Storage Productivity Center for Replication database data is changed, such
as adding or deleting a storage system, changing properties, and changing user
privileges.
򐂰 After an Tivoli Storage Productivity Center for Replication session changes direction. For
example, if an MM session was copying data from H1 to H2 when the backup was taken,
and later, the session was started in the H2 to H1 direction. The session must be in the
Prepared state before you create the backup.
򐂰 After a site switch was declared and the Enable Copy To Site command was issued. After
you create a backup, consider deleting the previous backup to prevent Tivoli Storage
Productivity Center for Replication from starting the copy in the wrong direction.

140 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: You must have Administrator privileges to back up and restore the Tivoli Storage
Productivity Center for Replication repository.

Also, ensure that all Tivoli Storage Productivity Center for Replication sessions are in the
Defined, Prepared, or Target Available state before the backup is created.

Backing up Tivoli Storage Productivity Center for Replication repository

To back up the Tivoli Storage Productivity Center for Replication repository, you run the
mkbackup command from the Tivoli Storage Productivity Center for Replication CLI. For more
information about how to start the CLI, see 3.1.2, “Accessing Tivoli Storage Productivity
Center for Replication CLI” on page 65.

Example 3-26 shows you how to start a backup of Tivoli Storage Productivity Center for
Replication repository.

Example 3-26 Backup of Tivoli Storage Productivity Center for Replication repository
C:\Program Files\IBM\TPC\cli>csmcli
Tivoli Storage Productivity Center for Replication Command Line Interface (CLI)
Copyright 2007, 2012 IBM Corporation
Version: 5.2.0
Build: 20130719-0641
Server: SSCTCP42-T.windows.ssclab-lj-si.net Port: 9560
Authentication file: C:\Users\tpcadmin\tpcr-cli\tpcrcli-auth.properties

csmcli> mkbackup
IWNR1905I [Aug 14, 2013 2:18:30 AM] Backup of internal data store completed
successfully. The following file was created: C:\Program
Files\IBM\TPC\wlp\usr\servers\replicationServer\database\backup\tpcrBackup_2013081
4_021829944.zip
csmcli>

The backup is created in a new file when you create a backup. It is your responsibility to
delete backup versions that are no longer needed. The backup file is named
yyyyMMdd_HHmmssSSS.zip, where:
򐂰 yyyy is the year
򐂰 MM is the month
򐂰 dd is the day
򐂰 HH is the hour
򐂰 mm is the minute
򐂰 ss is the seconds
򐂰 SSS is the milliseconds when the backup command was run

By default, the backup file is stored in the following location:

TPC_Install\ProgramFiles\IBM\TPC\wlp\usr\servers\replicationServer\database\backup

You can change the default location by editing the db.backup.location property in the
rmserver.properties file. The rmserver.properties file is in the following location:

TPC_Install\Program Files\IBM\TPC\wlp\usr\servers\replicationServer\properties

Chapter 3. General administration and high availability 141

 Example 3-27 shows you how to change rmserver.properties file.

Example 3-27 Location of Tivoli Storage Productivity Center for Replication repository backup
# Property db.backup.location: [ backup directory ]
# This property controls where the internal data store will be backed up
# when using the mkbackup command. The default in the code is database/backup
# and relative to the runtime directory. Only change this if you want to
# direct the backup files to be written to a different location. NOTE: This
# property is not required to be set in this file.
db.backup.location=database/backup

Restoring Tivoli Storage Productivity Center for Replication repository

Restoring of the Tivoli Storage Productivity Center for Replication repository from a backup
file takes the Tivoli Storage Productivity Center for Replication back to the point when the
backup was made. Relationships on the storage systems that were created by Tivoli Storage
Productivity Center for Replication after the backup was made no longer are managed by
Tivoli Storage Productivity Center for Replication until you add the copy set to the session and
Tivoli Storage Productivity Center for Replication assimilates the relationship into the session.
Copy sets that were deleted after the backup are restored and a subsequent Start command
to the session creates relationships. Therefore, you must remove the deprecated copy sets
before the Start command is run.

Note: After a GM session is restored, you must stop the GM master and subordinates
before the GM session is restarted.

Also, restoring the database does not require Administrator privileges. However, you must
access the files on the Tivoli Storage Productivity Center for Replication server where you
backed up the Tivoli Storage Productivity Center for Replication.

Complete the following steps to restore the Tivoli Storage Productivity Center for Replication
repository from a backup file:
1. Stop Tivoli Storage Productivity Center for Replication on the active management server
by running the stopTPCReplication.bat command, as described in “Starting and stopping
Tivoli Storage Productivity Center for Replication” on page 127 and shown in
Example 3-28.

Example 3-28 Stopping Tivoli Storage Productivity Center for Replication

C:\Program Files\IBM\TPC\scripts>stoptpcreplication
Server replicationServer stopped.
No Instance(s) Available.

C:\Program Files\IBM\TPC\scripts>

2. Delete the csmdb directory and all of its contents, as shown in Figure 3-92 on page 143.
The csmdb directory is in
TPC_Install\IBM\TPC\wlp\usr\servers\replicationServer\database.

142 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-92 Deleting csmdb

3. Extract the backup file into the

TPC_Install\IBM\TPC\wlp\usr\servers\replicationServer\database directory, as
shown in Figure 3-93.

Figure 3-93 Extracting backup file

Chapter 3. General administration and high availability 143

 4. Restart IBM Tivoli Storage Productivity Center for Replication on the active management
server by running the startTPCReplication.bat command, as described in “Starting and
stopping Tivoli Storage Productivity Center for Replication” on page 127 and shown in
Example 3-29.

Example 3-29 Start Tivoli Storage Productivity Center for Replication

C:\Program Files\IBM\TPC\scripts>starttpcreplication

C:\Program Files\IBM\TPC\scripts>

5. Resolve any changes that occurred since the backup was created.
6. Start the IBM Tivoli Storage Productivity Center for Replication sessions by using the
appropriate start commands. The start commands reestablish the relationship between
the volume pairs and synchronize data on those volumes. If you have a standby
management server, reestablish that standby relationship to update the database on the
standby server, as shown in Figure 3-94.

Figure 3-94 Reconnecting Standby Tivoli Storage Productivity Center for Replication server

3.12 Tivoli Storage Productivity Center for Replication SNMP

management
Tivoli Storage Productivity Center for Replication servers can send Simple Network
Management Protocol (SNMP) traps to registered SNMP managers when various events
occur. In the following sections, the SNMP alerts and the basic SNMP setup are described.

3.12.1 SNMP Alerts

SNMP alerts are sent during the following general events:
򐂰 Session state change
򐂰 Configuration change
򐂰 Suspending-event notification
򐂰 Communication failure
򐂰 Management Server state change

In the following sections, trap descriptions for an event are described.

144 Tivoli Storage Productivity Center for Replication for Open Systems
Session state change SNMP trap descriptions
This section describes the SNMP traps that are sent during a session state change. A
different trap is sent for each state change.

Note: Traps for Session state change events are sent only by the Tivoli Productivity Center
for Replication active server.

A session state change SNMP trap is sent when the session changes to one of the following
states:
򐂰 Defined
򐂰 Preparing
򐂰 Prepared
򐂰 Suspended
򐂰 Recovering
򐂰 Flashing
򐂰 Target Available
򐂰 Suspending
򐂰 (Metro Global Mirror only) SuspendedH2H3
򐂰 (Metro Global Mirror only) SuspendedH1H3

In addition, session state change SNMP traps are sent when a recovery point objective
(RPO) threshold (warning or severe threshold) is exceeded for a role pair that is in the
session.

Configuration change SNMP trap descriptions

This section describes the SNMP traps that are sent when a configuration change occurs.

Note: Traps for configuration change events are sent only by Tivoli Storage Productivity
Center for Replication active server.

Configuration change SNMP traps are sent after the following configurations changes are
made:
򐂰 One or more copy sets are added or deleted from a session.
򐂰 PPRC path definitions are changed.

Suspending-event notification SNMP trap descriptions

These SNMP traps that are sent during a suspending-event notification. Suspending-event
notification SNMP traps indicate that a session moved to a Severe status because of an
unexpected error.

Note: Traps for suspension events are sent only by the Tivoli Storage Productivity Center
for Replication active server.

Communication-failure SNMP trap descriptions

This section describes the SNMP traps that are sent during a communication-failure.

Note: Traps for communication failure events are sent by active and Stand-by Tivoli
Storage Productivity Center for Replication servers.

Chapter 3. General administration and high availability 145

 Communication-failure SNMP traps are sent after the following events occur:
򐂰 A server times out when it attempts to communicate with a storage system.
򐂰 A server encounters errors when it attempts to communicate with a storage system.
򐂰 An active server terminates communication with a standby server because of
communication errors.
򐂰 A standby encounters communication errors with an active server.

Management Servers state-change SNMP trap descriptions

This section describes the SNMP traps that are sent when the state of the management
server changes.

Note: Traps for communication failure events are sent by active and Stand-by Tivoli
Storage Productivity Center for Replication servers.

A management server state change SNMP trap is sent when the management server
changes to one of the following states:
򐂰 Unknown
򐂰 Synchronization Pending
򐂰 Synchronized
򐂰 Disconnected Consistent
򐂰 Disconnected

Tivoli Storage Productivity Center for Replication SNMP traps summary

The Table 3-3 on page 147 summarize the Tivoli Storage Productivity Center for Replication
SNMP traps that are reporting their respective Object ID for each type of event.

146 Tivoli Storage Productivity Center for Replication for Open Systems
Table 3-3 Tivoli Storage Productivity Center for Replication traps description
Event Object ID Trap description

Session state 1.3.6.1.4.1.2.6.208.0.1 The state of session X changed to Defined.

change event
1.3.6.1.4.1.2.6.208.0.2 The state of session X changed to Preparing.

1.3.6.1.4.1.2.6.208.0.3 The state of session X changed to Prepared.

1.3.6.1.4.1.2.6.208.0.4 The state of session X changed to Suspended.

1.3.6.1.4.1.2.6.208.0.5 The state of session X changed to Recovering.

1.3.6.1.4.1.2.6.208.0.6 The state of session X changed to Target Available.

1.3.6.1.4.1.2.6.208.0.19 The state of session X changed to Suspending.

1.3.6.1.4.1.2.6.208.0.20 The state of session X changed to

SuspendedH2H3.

1.3.6.1.4.1.2.6.208.0.21 The state of session X changed to

SuspendedH1H3.

1.3.6.1.4.1.2.6.208.0.22 The state of session X changed to Flashing.

1.3.6.1.4.1.2.6.208.0.23 The state of session X changed to Terminating.

1.3.6.1.4.1.2.6.208.0.26 The recovery point objective for the role pair of X in

session Y passed the warning threshold of Z
seconds.

1.3.6.1.4.1.2.6.208.0.27 The recovery point objective for the role pair of X in

session Y passed the severe threshold of Z
seconds

Configuration 1.3.6.1.4.1.2.6.208.0.7 One or more copy sets were added or deleted from
change event this session.

An event is sent for each session at least every 15

minutes.

1.3.6.1.4.1.2.6.208.0.8 Peer-to-Peer Remote Copy (PPRC) path

definitions were changed. An event is sent for each
path configuration change.

Suspension event 1.3.6.1.4.1.2.6.208.0.9 The session is in a Severe state because of an

unexpected error.

Communication 1.3.6.1.4.1.2.6.208.0.10 Server X timed out attempting to communicate

failure event with storage system Y.

1.3.6.1.4.1.2.6.208.0.11 Server X encountered errors while attempting to

communicate with storage system Y.

1.3.6.1.4.1.2.6.208.0.12 Active server X terminated communication with

standby server Y because of communication
errors.

1.3.6.1.4.1.2.6.208.0.13 Standby server X encountered communication

errors with active server Y.

Chapter 3. General administration and high availability 147

 Event Object ID Trap description

Management 1.3.6.1.4.1.2.6.208.0.14 The IBM Tivoli Storage Productivity Center for

Server state Replication Server Management Server
change event connection X → Y changed state to Unknown
(previously Offline).

1.3.6.1.4.1.2.6.208.0.15 The IBM Tivoli Storage Productivity Center for

Replication Server Management Server
connection X → Y changed state to Synchronized.

1.3.6.1.4.1.2.6.208.0.16 The IBM Tivoli Storage Productivity Center for

Replication Server Management Server
connection X → Y changed state to Disconnected
Consistent (previously Consistent Offline).

1.3.6.1.4.1.2.6.208.0.17 The IBM Tivoli Storage Productivity Center for

Replication Server Management Server
connection X → Y changed state to
Synchronization Pending.

1.3.6.1.4.1.2.6.208.0.18 The IBM Tivoli Storage Productivity Center for

Replication Server Management Server
connection X → Y changed state to Disconnected.

3.12.2 SNMP setup

Complete the following steps to set up the SNMP on Tivoli Storage Productivity Center for
Replication:
1. Configure the SNMP community name. By default, the SNMP community name on Tivoli
Storage Productivity Center for Replication has a value of public. To change the
community name, modify or add the csm.server.snmp_community_string property in the
rmserver.properties file, which is in the
WAS_HOME/usr/servers/replicationServer/properties directory.
2. Add the SNMP managers. To add an SNMP manager, the mksnmp CLI command must be
used, as shown in Example 3-30.

Example 3-30 mksnmp CLI command to add an SNMP manager

csmcli> mksnmp -server 192.0.0.4 -port 166
IWNR1701I [Aug 19, 2013 4:02:45 PM] Host 192.0.0.4:166 was added to the SNMP
listeners list.

To check the list of SNMP managers that are configured on Tivoli Storage Productivity
Center for Replication, use the lssnmp CLI command, as shown in Example 3-31.

Example 3-31 lssnmp CLI command to list the SNMP managers configured
csmcli> lssnmp
SNMP Manager Port
=================
192.0.0.4 166
192.0.0.3 162
192.0.0.2 162
192.0.0.1 162

148 Tivoli Storage Productivity Center for Replication for Open Systems
 3. Configure the SNMP managers with the Tivoli Storage Productivity Center for Replication
MIB files. Tivoli Storage Productivity Center for Replication uses management information
base (MIB) files to provide a textual description of each SNMP alert that is sent by IBM
Tivoli Storage Productivity Center for Replication. You must configure the SNMP manager
to use the SYSAPPL-MIB.mib and ibm-TPC-Replication.mib files. These MIB files are in the
installation DVD in the root/replication/CSM-Client/etc directory. Follow the directions
that are provided by your SNMP manager application to configure it to use the MIB files.

Tivoli Storage Productivity Center for Replication sends all SNMP alerts to each registered
SNMP manager. SNMP alerts are not specific to any particular session, and all alerts for any
session are sent. You cannot choose to send a subset of SNMP alerts; nevertheless, the
information that is reported in Table 3-3 on page 147 can be used to configure the SNMP
manager to discard the traps considered irrelevant.

Note: By default, Tivoli Storage Productivity Center for Replication sends SNMP traps to
the Tivoli Storage Productivity Center alerting feature (see 3.4, “Tivoli Storage Productivity
Center for Replication interaction with Tivoli Storage Productivity Center” on page 88). You
can configure the Tivoli Storage Productivity Center for Replication to change the
destination Tivoli Storage Productivity Center where to send these traps by changing the
csm.server.tpc_data_server.address property in the rmserver.properties file, which is
in the WAS_HOME/usr/servers/replicationServer/properties directory.

3.13 Adding and connecting to storage systems

You must add connections to storage systems before you can use Tivoli Storage Productivity
Center for Replication to manage data replication.

Complete the following steps to add a storage system by using the Tivoli Storage Productivity
Center for Replication GUI:
1. In the navigation tree, select Storage Systems. The Storage Systems Welcome page
opens, as shown in Figure 3-95 on page 150. This page lists all of the storage systems
that were added to Tivoli Storage Productivity Center for Replication.

Chapter 3. General administration and high availability 149

 Figure 3-95 Storage Systems Welcome page

2. On the Storage Systems page, click Add Storage Connection, as shown in Figure 3-96.

Figure 3-96 Adding a connection to a storage system

3. On the Type page of the Add Storage System wizard (see Figure 3-96), click the icon for
the storage system that you want to add. The Connection page of the wizard opens.

Note: On the Type page of the Add Storage System wizard, use the Storwize Family
icon to add a Storwize V3500, Storwize V3700, or Storwize V7000 storage system.

150 Tivoli Storage Productivity Center for Replication for Open Systems
 4. An example of a DS8000 connection) is shown on the Connection page, a shown in
Figure 3-97 on page 152. Complete the connection information for the storage system.

The following sections show the Connection page for DS8000, SAN Volume Controller, and
XIV systems. The fields are the same on the Connection pages for SAN Volume Controller
Storwize Family, and Storwize V7000 Unified storage systems.

3.13.1 DS8000 Connection page

You must use a Hardware Management Console (HMC) connection to connect to a DS8000
storage system if the system is a DS8700 or later or is on an Internet Protocol version 6
(IPv6) network.

If the storage system is earlier than DS8700 and is on an Internet Protocol version 4 (IPv4)
network, you can connect to the system directly.

Setting up an HMC connection

Click HMC and complete the connection information for the primary and optional secondary
HMC, as shown in Figure 3-97 on page 152. A secondary HMC is used for redundancy. Both
HMCs must be configured identically and must have the same user name and password.

Note: A dual HMC (primary and secondary HMC) while optional is highly recommended
for redundancy purposes when Tivoli Storage Productivity Center for Replication is used.

Chapter 3. General administration and high availability 151

 Figure 3-97 Add a DS8000 connection by using an HMC connection

Setting up a Direct connection

Click Direct Connect and complete the connection information for cluster 0 and cluster 1, as
shown in Figure 3-98 on page 153. The port, user name, and password for cluster 0 are
automatically entered in the corresponding fields for cluster 1. You can edit this information, if
required for your environment.

152 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 3-98 Add a DS8000 connection by using a direct connection

Chapter 3. General administration and high availability 153

 Complete the connection information as shown in Figure 3-99.

Figure 3-99 Add a SAN Volume Controller connection

154 Tivoli Storage Productivity Center for Replication for Open Systems
3.13.2 XIV System Storage Connection window
Complete the connection information as shown in Figure 3-100.

Figure 3-100 Add an XIV system connection

Tip: When you are entering the connection information as shown in Figure 3-100, you
must enter the IP information for only one of the nodes. Tivoli Storage Productivity Center
for Replication discovers the rest automatically.

3.14 Adding and connecting host systems

Host systems are required to enable certain replication features for storage systems. There
are two types of host systems to which you can connect: an AIX host system or a z/OS host
system.

A connection to an AIX host system is required if you want to enable the Open HyperSwap
feature in Metro Mirror Failover/Failback sessions.

Chapter 3. General administration and high availability 155

 A connection to a z/OS host is required if you want to enable z/OS features such as
HyperSwap and the management of freeze operations in Tivoli Storage Productivity Center
for Replication sessions.

If Tivoli Storage Productivity Center for Replication is installed on the z/OS host system, the
host system connection is automatically displayed on the Host Systems page. This
connection is referred to as the native z/OS connection.

Note: If Tivoli Storage Productivity Center for Replication is installed on a z/OS system
other than the host system, you must add the connection to the host system by using a
host name or IP address for the system.

Complete the following steps to add a host system by using the Tivoli Storage Productivity
Center for Replication GUI:
1. In the navigation tree, select Host Systems. The Host Systems window opens. A list of all
host systems that were added to Tivoli Storage Productivity Center for Replication
appears.
2. On the Host Systems window, click Add Host Connection, as shown in Figure 3-101.
The Add Host Connection window opens.

Figure 3-101 Adding a connection to a host system

3. In the Add Host Connection window, select the host system type and complete the
connection information for the host. The following sections provide connection information
by host system type.

156 Tivoli Storage Productivity Center for Replication for Open Systems
3.14.1 AIX Host System
Select AIX and complete the connection information for the host system, as shown in
Figure 3-102.

Figure 3-102 Add an AIX host connection

3.14.2 z/OS Host System

Select z/OS and complete the connection information for the host system, as shown in
Figure 3-103.

Note: The port number, user name, and password must be the same as the values that are
specified for management address space IOSHMCTL SOCKPORT parameter and
Resource Access Control Facility (RACF®) settings on the host system. For more
information about the host system configuration, see the IBM Tivoli Storage Productivity
Center for Replication for System Z Installation and Configuration Guide, SC27-4091.

Figure 3-103 Add a z/OS host connection

Chapter 3. General administration and high availability 157

158 Tivoli Storage Productivity Center for Replication for Open Systems
 4

Chapter 4. Using Tivoli Storage Productivity

Center for Replication with
DS8000
In this chapter, we describe the latest functions for DS8000 that are supported up to Tivoli
Storage Productivity Center for Replication v5.2 for open systems.

We also show you how to set up replication sessions and how to manage sessions. Also
provided are state transition diagrams for session types. The state transition diagrams
describe each session and show the potential states and the next steps to perform.

Finally, we describe some helpful use cases and provide recommendations for how to
perform disaster recovery scenarios. We also provide troubleshooting guidance.

This chapter includes the following topics:

򐂰 Capabilities overview
򐂰 New functions for DS8000
򐂰 Managing DS8000 sessions
򐂰 Use cases
򐂰 Troubleshooting

© Copyright IBM Corp. 2014. All rights reserved. 159

4.1 Capabilities overview
DS8000 Copy Services is a collection of functions that provide disaster recovery, data
migration, and data duplication solutions. There are two main types of Copy Services
functions: Point-in-Time Copy that includes the FlashCopy capabilities, and Remote Mirror
and Copy that includes the Metro Mirror, Global Copy, Global Mirror, and Metro/Global Mirror
capabilities. The Point-in-Time Copy functions are used for data duplication, and the Remote
Mirror and Copy functions are used for data migration, high availability, and disaster recovery.

For more information about DS8000 Copy Services, see IBM System Storage DS8000 Copy
Services for IBM System z, SG24-6787, and IBM System Storage DS8000 Copy Services for
Open Systems, SG24-6788.

The DS8000 copy services functions support open systems (Fixed Block) and System z
count key data (CKD) volumes.

Tivoli Storage Productivity Center for Replication provides management for the DS8000 copy
services in various combinations. In the following sections, we provide an overview of the
Tivoli Storage Productivity Center for Replication capabilities for DS8000 Copy Services.

To describe the flow of the operations that Tivoli Storage Productivity Center for Replication
supports for each session type, State Transition Diagrams are provided. These diagrams are
not intended to be exhaustive of all the actions that Tivoli Storage Productivity Center for
Replication can start in every specific condition (for example, the StartGC actions are not
shown in any diagram), but they list the actions that are considered the most significant to
describe the product capabilities. Table 4-1 shows a description of the notation that is used in
the state transition diagrams.

Table 4-1 State transition diagrams notation

Notation Description

Session status is in Defined state.

Session status is in a Normal state.

Session status is Severe.

Session status is in a Warning state.

Denotes a state transition following the Action

160 Tivoli Storage Productivity Center for Replication for Open Systems
 Notation Description

Denotes a condition in which the host should work on the Location

Site.

Denotes a state transition following the action of Enabling the Copy

to SiteX.

4.1.1 FlashCopy
By using the DS8000 FlashCopy feature, you can create point-in-time copies of logical
volumes that make source and target copies immediately available to the users.

When a FlashCopy operation is started, it takes only a few seconds to complete the process
of establishing the FlashCopy pair and creating the necessary control bitmaps. Thereafter,
you have access to a Point-in-Time Copy of the source volume. When the pair is established,
you can read and write to the source and target volumes.

In a FlashCopy relationship, the source and target volumes must exist within the same
storage system. For this reason, FlashCopy is considered to be a single-site replication
capability.

The following variations of FlashCopy are available:

򐂰 Standard FlashCopy: Uses a fully provisioned volume as a target volume.
򐂰 FlashCopy Space Efficient (SE): Uses Track-Space-Efficient volumes as FlashCopy target
volumes and must be in a background no-copy relationship. An SE volume has a virtual
size that is equal to the source volume size. However, space is not allocated when the
volume is created and the FlashCopy started. Space is allocated in a repository when a
first update is made to a track on the source volumes, which causes the source track to be
copied to the FlashCopy SE target volume to maintain the point-in-time copy. Writes to the
SE target also use repository space.
򐂰 Extent-Space-Efficient (ESE) volume FlashCopy is supported starting with the DS8000
microcode version 6.2. With this kind of FlashCopy, space is not allocated when the thin
provisioned volume is created. Extents are allocated from an extent pool when the first
update is made to an extent on the thin-provisioned volume. Thin provisioning does not
use tracks from a repository; instead, they use tracks from the extent pool.

Note: Tivoli Storage Productivity Center for Replication support for ESE volumes in all
remote copy relationship is available with version 5.1 or higher.

Tivoli Storage Productivity Center for Replication manages all the variations of DS8000
FlashCopy through the Point in Time session types that currently includes only the FlashCopy
session. The FlashCopy session is shown in Figure 4-1 on page 162.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 161
 Figure 4-1 FlashCopy session

With this type of session, Tivoli Storage Productivity Center for Replication users can start a
FlashCopy for all the volumes in the session. Figure 4-2 shows the state changes for a
FlashCopy session.

Figure 4-2 Change state diagram for a FlashCopy session

4.1.2 Metro Mirror

DS8000 Metro Mirror, which is also known as synchronous Peer-to-Peer Remote Copy
(PPRC) is a two-site, synchronous remote copy technology. It provides real-time mirroring of
logical volumes between two DS8000s that can be up to 300 km from each other. As a
synchronous copy solution, write operations are completed on both copies (primary and
secondary site) before they are considered to be complete. The Metro Mirror is the main
building block of the high-availability solutions and is based on the DS8000 HyperSwap
capabilities.

When a Metro Mirror operation is started, a mirroring relationship is established between the
source and the target volume and a control bitmap of the out-of-sync tracks is created. Then,
a full asynchronous copy process starts. After the initial copy is completed, the relationship
goes to Full Duplex status and the mirroring process become synchronous.

Tivoli Storage Productivity Center for Replication manages all of the variations of DS8000
Metro Mirror through the Synchronous session types that include three Metro Mirror
sessions.

162 Tivoli Storage Productivity Center for Replication for Open Systems
Metro Mirror Single Direction
With the Metro Mirror Single Direction session type, Metro Mirror replication is available only
from the primary site and it is not allowed any action that inverts the replication direction. With
this type of session, Tivoli Storage Productivity Center for Replication allows user to perform
the following tasks:
򐂰 Start the Metro Mirror.
򐂰 Pause and resume the Metro Mirror.
򐂰 Recover the Metro Mirror secondary site volumes, which makes them available for the use
at the remote site.
򐂰 Restart the Metro Mirror following a recovery. This is accomplished by performing an
incremental copy.

The Metro Mirror Single Direction session is shown in Figure 4-3.

Figure 4-3 Metro Mirror Single Direction session

The state changes for a Metro Mirror Single Direction session are shown in Figure 4-4.

Figure 4-4 State changes for a Metro Mirror Single Direction session

Metro Mirror Failover/Failback

The Metro Mirror Failover/Failback session type enables the direction of the data replication to
switch. With this session type, it is possible to use the secondary site as the production site
and then copy changes that are made at the secondary site back to the primary site. By using
this type of Tivoli Storage Productivity Center for Replication session, uses can perform the
following tasks:
򐂰 Start the Metro Mirror.
򐂰 Pause and resume the Metro Mirror.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 163
 򐂰 Recover the Metro Mirror secondary volumes and make them available for use at the
secondary site.
򐂰 Restart the Metro Mirror following a recovery. This is accomplished by performing an
incremental resynchronization.
򐂰 Perform a switch site role, which makes the secondary site source for the replication.
򐂰 Restart the Metro Mirror following a switch site role, which copies the changes that are
made at the secondary site back to the primary. This is accomplished performing an
incremental resynchronization.
򐂰 Resume the original direction of the Metro Mirror after switching back to the original site
roles. This is accomplished by performing an incremental resynchronization.

Open HyperSwap: With version 4.2 or higher, Tivoli Storage Productivity Center for
Replication supports the Open HyperSwap function for Metro Mirror Failover/Failback
session type. For more information about Open HyperSwap, see 2.1.6, “HyperSwap
configuration for z/OS and Open systems” on page 45.

The Metro Mirror Failover/Failback session is shown in Figure 4-5.

Figure 4-5 Metro Mirror Failover/Failback session

The state changes for a Metro Mirror Failover/Failback session are shown in Figure 4-6 on
page 165. Table 4-1 on page 160 provides a description of the states.

164 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-6 Change state diagram for a Metro Mirror Failover/Failback session

Metro Mirror Failover/Failback with Practice

Metro Mirror Failover/Failback with Practice replication combines Metro Mirror
Failover/Failback and FlashCopy capabilities to provide a point-in-time copy of the data on the
secondary site. This session type provides volumes that can be used to practice for disaster
recovery without losing your disaster recovery capability. By using this type of Tivoli Storage
Productivity Center for Replication session, you can perform the following tasks:
򐂰 Start the Metro Mirror.
򐂰 Pause and resume the Metro Mirror.
򐂰 Create a consistent copy of Metro Mirror secondary site at the secondary site by using
FlashCopy. This copy can be used as a practice copy for DR test.
򐂰 Recover the Metro Mirror secondary site volumes and make them available for use at the
secondary site. This also creates a copy of Metro Mirror secondary site at the remote site
by using FlashCopy.
򐂰 Restart the Metro Mirror following a recovery. This is accomplished by performing an
incremental resynchronization.
򐂰 Perform a switch site role, which makes the secondary site the source for the replication.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 165
 򐂰 Restart the Metro Mirror following a switch site role, which copies the changes that were
made at the secondary site back to the primary. This is accomplished by performing an
incremental copy.
򐂰 Resume the original direction of the Metro Mirror after switching back to the original site
roles. This is accomplished by performing a full copy.

Limitation: The use of Track Space Efficient volumes as a FlashCopy target for practice
copy (H2 volumes) is not allowed in this session type.

The Metro Mirror Failover/Failback with Practice session is shown in Figure 4-7.

Figure 4-7 Metro Mirror Failover/Failback with Practice session

The state changes for a Metro Mirror Failover/Failback with Practice session are shown in
Figure 4-8 on page 167.

166 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-8 Change state diagram for a Metro Mirror Failover/Failback with Practice session

4.1.3 Global Mirror

DS8000 Global Mirror, previously known as Asynchronous PPRC, is a two-site, long-distance,
asynchronous, remote copy technology. This solution integrates the Global Copy and
FlashCopy technologies. With Global Mirror, the data that the host writes at the primary
(local) site is asynchronously mirrored to the storage unit at the secondary (remote) site. With
special management steps and under control of the local master storage unit, a consistent
copy of the data is automatically maintained and periodically updated by using FlashCopy on
the storage unit at the remote site.

Note: You need extra storage at the remote site for these FlashCopies. Because of its
asynchronous mirroring characteristics, the Global Mirror supports unlimited distances
between the local and remote site.

It is typically used for disaster recovery (DR) solutions or for those applications that cannot be
affected by the latency effects of synchronous replication.

Tivoli Storage Productivity Center for Replication manages all of the variations of DS8000
Global Mirror through the Asynchronous session types that include four Global Mirror
sessions.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 167
 Global Mirror Single Direction session
With the Global Mirror Single Direction session type, Global Mirror replication is available only
from the local site. Tivoli Storage Productivity Center for Replication does not allow any action
that inverts the replication direction. By using this type of Tivoli Storage Productivity Center for
Replication session, you can perform the following tasks:
򐂰 Start the Global Mirror.
򐂰 Pause and resume the Global Mirror.
򐂰 Recover Global Mirror secondary volumes, which makes them available for use at the
remote site.
򐂰 Restart the Global Mirror following a recovery. This is accomplished by performing an
incremental copy.

Note: Track Space Efficient volumes can be used as Journal volumes (J2 volumes) for this
session type.

The Global Mirror Single Direction session is shown in Figure 4-9.

Figure 4-9 Global Mirror Single Direction session

The state transitions for a Global Mirror Single Direction session are shown in Figure 4-10.

Figure 4-10 Change state diagram for a Global Mirror Single Direction session

168 Tivoli Storage Productivity Center for Replication for Open Systems
Global Mirror Failover/Failback
The Global Mirror Failover/Failback session type enables the direction of the data replication
to be switched. With this session type, the remote site can be used as a production site and
changes that are made at the remote site are copied back to the local site. By using this type
of Tivoli Storage Productivity Center for Replication session, you can perform the following
tasks:
򐂰 Start the Global Mirror.
򐂰 Pause and resume the Global Mirror.
򐂰 Recover the Global Mirror secondary volumes, which makes them available for use at the
remote site.
򐂰 Restart the Global Mirror following a recovery. This is accomplished by performing an
incremental resynchronization.
򐂰 Perform a switch site role, which makes the remote site the source for the replication.
򐂰 Restart the replication (only the Global Copy) following a switch site role, which copies the
changes that were made at the remote site back to the local. This is accomplished by
performing an incremental resynchronization.
򐂰 Resume the original direction of the Global Mirror after returning to the original site roles.
This is accomplished by performing an incremental resynchronization.

Note: Track Space Efficient volumes can be used as Journal volumes (J2 volumes) for this
session type.

The Global Mirror Failover/Failback session is shown in Figure 4-11.

Figure 4-11 Global Mirror Failover/Failback session

The state transitions for a Global Mirror Failover/Failback session are shown in Figure 4-12 on
page 170.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 169
 Figure 4-12 Change state diagram for a Global Mirror Failover/Failback session

Global Mirror Failover/Failback with Practice

Global Mirror Failover/Failback with Practice replication combines Global Mirror
Failover/Failback and FlashCopy capabilities to provide a point-in-time copy of the data on the
remote site. This session type provides volumes that can be used to practice for disaster
recovery without losing your disaster recovery capability. By using this type of Tivoli Storage
Productivity Center for Replication session, you can perform the following tasks:
򐂰 Start the Global Mirror.
򐂰 Pause and resume the Global Mirror.
򐂰 Create a consistent copy of Global Mirror secondary site at the remote site by using
FlashCopy. This copy can be used as practice copy for a DR test.
򐂰 Recover the Global Mirror secondary site volume, which makes them available for use in
the remote site. This also creates a copy of Global Mirror secondary site in the remote site
by using the FlashCopy.
򐂰 Restart the Global Mirror following a recovery. This is accomplished by performing an
incremental resynchronization.
򐂰 Perform a switch site role, which makes the remote site the source for the replication.

170 Tivoli Storage Productivity Center for Replication for Open Systems
򐂰 Restart the replication (only the Global Copy) following a switch site role, which copies the
changes that were made at the remote site back to the local. This is accomplished by
performing an incremental copy.
򐂰 Resume the original direction of the Global Mirror after returning to the original site roles.
This is accomplished by performing a full copy.

Limitation: Track Space Efficient (TSE) volumes can be used only for Journal volumes (J2
volumes) for this session type. TSE volumes cannot be used as FlashCopy targets for the
practice copy (H2 volumes) in Tivoli Storage Productivity Center for Replication.

The Global Mirror Failover/Failback with Practice session is shown in Figure 4-13.

Figure 4-13 Global Mirror Failover/Failback with Practice session

Figure 4-14 on page 172 shows the state transitions for a Global Mirror Failover/Failback with
Practice session. Table 4-1 on page 160 provides a description of the states.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 171
 Figure 4-14 Change state diagram for a Global Mirror Failover/Failback with Practice session

Global Mirror Either Direction with Two-Site Practice

By using Global Mirror Either Direction with Two-Site Practice replication, you can run Global
Mirror replication from the local or remote site. This session type provides volumes on the
local and remote site that you can use to practice for disaster recovery without losing your
disaster recovery capability. This type of Tivoli Storage Productivity Center for Replication
session allows a user to perform the following tasks:
򐂰 Start the Global Mirror.
򐂰 Pause and resume the Global Mirror.
򐂰 Create a consistent copy of Global Mirror secondary site at the remote site by using the
FlashCopy. This copy can be used as a practice copy for disaster recovery test.
򐂰 Recover the Global Mirror secondary site volumes, which makes them available for use in
the remote site. This also creates a copy of Global Mirror secondary site in the remote site
by using the FlashCopy.
򐂰 Restart the Global Mirror following a recovery. This is done by performing an incremental
resynchronization.
򐂰 Perform a switch site role, which makes the remote site the source for the replication.

172 Tivoli Storage Productivity Center for Replication for Open Systems
򐂰 Restart the Global Mirror following a switch site role, which copies the changes that were
made at the remote site back to the local. This is accomplished by performing a full copy. A
full disaster recovery capability is now restored between the original remote and local site.
򐂰 Resume the original direction of the Global Mirror after returning to the original site roles.
This is accomplished performing a full copy.

Limitation: TSE volumes can be used only for Journal volumes (J2 and J1 volumes) for
this session type. TSE volumes cannot be used as FlashCopy targets for the practice copy
(H2 and H1 volumes) in Tivoli Storage Productivity Center for Replication.

The Global Mirror Either Direction with Two-Site Practice session is shown in Figure 4-15.

Figure 4-15 Global Mirror Either Direction with Two Site Practice

The state transitions for a Global Mirror Either Direction with Two-Site Practice session is
shown in Figure 4-16 on page 174.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 173
 Figure 4-16 Change state diagram for a Global Mirror Either Direction with Two-Site Practice session

4.1.4 Metro Global Mirror

The Metro Global Mirror function enables a three-site, high-availability disaster recovery
solution. It combines the capabilities of Metro Mirror and Global Mirror functions for greater
protection against planned and unplanned outages. Metro Global Mirror uses synchronous
replication to mirror data between a local site and an intermediate site, and asynchronous
replication to mirror data from an intermediate site to a remote site. In this configuration, a
Metro Mirror pair is established between two nearby sites (local and intermediate) to protect
from local site disasters. The Global Mirror volumes can be thousands of miles away and
continue to be updated if the original local site suffered a disaster and I/O must be failed over
to the intermediate site.

Metro Global Mirror is fully supported only on the DS8000, while the ESS800 is supported
only when it is acting as primary (or active) site of the Metro Mirror.

Tivoli Storage Productivity Center for Replication manages all of the variations of DS8000
Metro Global Mirror through the Three Sites session types that include two Metro/Global
Mirror sessions.

174 Tivoli Storage Productivity Center for Replication for Open Systems
Metro Global Mirror combines Metro Mirror synchronous copy and Global Mirror
asynchronous copy into a single session, where the Metro Mirror target is the Global Mirror
source. By using Metro Global Mirror replication, you can switch the direction of the data flow
so that you can use your intermediate or remote site as your production site. By using this
type of Tivoli Storage Productivity Center for Replication session, a user can perform the
following tasks:
򐂰 Start the Metro Global Mirror.
򐂰 Pause and resume both Metro Mirror and Global Mirror leg of Metro Global Mirror.
򐂰 Start the Global Mirror directly from local site to remote site. This uses the Global Mirror
Incremental Resync feature.
򐂰 Recover the Metro Mirror secondary site volumes, which makes them available for use in
the intermediate site.
򐂰 Recover the Global Mirror secondary site volumes, which makes them available for the
use in the remote site.
򐂰 Restart the Metro Global Mirror following a recovery of Metro Mirror or Global Mirror
secondary site.
򐂰 Perform a switch site role, which makes the intermediate or the remote site source for the
primary replication.
򐂰 Start a Metro Global Mirror that has the intermediate site volumes as the primary site for
the Metro Global Mirror. This is the typical HyperSwap scenario.
򐂰 Start a cascading Global Copy that has the remote site volumes as the primary site for the
replication. This is a typical Go-Home scenario.
򐂰 Start a Metro Mirror that has the intermediate site volumes as the primary site for the
Metro Mirror. This is the typical HyperSwap scenario when the remote site is not available.
򐂰 Resume the original direction of the Metro Global Mirror after returning to the original site
roles.

Note: TSE volumes can be used as Journal volumes (J3 volumes) for this session type.

The Metro Global Mirror session is shown in Figure 4-17.

Figure 4-17 Metro Global Mirror session

The state transitions for a Metro Global Mirror session that has the host running on Local site
is shown in Figure 4-18. For a description of the states, see Table 4-1 on page 160.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 175
Figure 4-18 Change state diagram for a Metro Global Mirror session while the host is running on Local Site

176 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-19 shows the state transitions for a Metro Global Mirror session when the host runs
on Intermediate site.

Figure 4-19 Change state diagram for a Metro Global Mirror session while the host is running on Intermediate Site

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 177
 Finally, Figure 4-20 shows the state transition for a Metro Global Mirror session when the host
is supposed to run on Remote site.

Figure 4-20 Metro Global Mirror session while the host is running on Remote Site

Metro Global Mirror with Practice

The Metro Global Mirror with Practice replication combines Metro Mirror, Global Mirror, and
FlashCopy capabilities to provide a point-in-time copy of the data on the remote site. This
session type provides volumes that you can use to practice for disaster recovery without
losing your disaster recovery capability. By using this type of Tivoli Storage Productivity
Center for Replication session, a user can perform the following tasks:
򐂰 Start the Metro Global Mirror.
򐂰 Pause and resume the Metro Mirror and Global Mirror leg of Metro Global Mirror.
򐂰 Create a consistent copy of Global Mirror secondary site at the remote site by using the
FlashCopy. This copy can be used as practice copy for disaster recovery testing.
򐂰 Start the Global Mirror directly from local site to remote site. This uses the Global Mirror
Incremental Resync feature.
򐂰 Recover the Metro Mirror secondary site volumes, which makes them available for the use
in the intermediate site.

178 Tivoli Storage Productivity Center for Replication for Open Systems
򐂰 Recover the Global Mirror secondary site volumes, which makes them available for use in
the remote site.
򐂰 Restart the Metro Global Mirror following a recovery of Metro Mirror or Global Mirror
secondary site.
򐂰 Perform a switch site role, making the intermediate or the remote site the source for the
primary replication.
򐂰 Start a Metro Global Mirror that has the intermediate site volumes as the primary site for
the Metro Global Mirror. This is the typical HyperSwap scenario.
򐂰 Start a cascade Global Copy that has the remote site volumes as the primary site for the
replication. This is a typical Go-Home scenario.
򐂰 Resume the original direction of the Metro Global Mirror after returning to the original site
roles.

Limitation: TSE volumes can be used only for Journal volumes (J3 volumes) for this
session type. Tivoli Storage Productivity Center for Replication does not allow the use of
TSE volumes as FlashCopy target for the practice copy (H3 volumes).

The Metro Global Mirror with Practice session is shown in Figure 4-21.

Figure 4-21 Metro Global Mirror with Practice session

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 179
 The state transitions for a Metro Global Mirror with Practice session that has the host running
on Local site is shown in Figure 4-22.

Figure 4-22 Metro Global Mirror with Practice session while the host is running on Local Site

180 Tivoli Storage Productivity Center for Replication for Open Systems
 The state transitions for a Metro Global Mirror with Practice session when the host is
supposed to run on Intermediate site are shown in Figure 4-23.

Figure 4-23 Metro Global Mirror with Practice session while the host is running on Intermediate Site

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 181
 The state transition for a Metro Global Mirror with Practice session when the host is running
on Remote site is shown in Figure 4-24.

Figure 4-24 Metro Global Mirror with Practice session while the host is running on Remote Site

4.2 New functions for DS8000

In this section, we describe the new functions for DS8000 that were introduced in the latest
versions of Tivoli Storage Productivity Center for Replication.

4.2.1 FlashCopy consistency groups for FlashCopy sessions

Consistency Group FlashCopy is an option of the FlashCopy capability that allows the
creation of a consistent point-in-time copy across multiple volumes, even across multiple
storage systems. By temporarily freezing the I/O activity on the volumes, consistency group
FlashCopy helps users to create a consistent point-in-time copy without quiescing the
application. Consistency Group FlashCopy ensures that the order of dependent writes is
always maintained and thus creates host-consistent copies, not application-consistent copies.
The copies have power-fail or crash level consistency.

182 Tivoli Storage Productivity Center for Replication for Open Systems
 To recover an application from Consistency Group FlashCopy target volumes, you must
perform the same recovery as is done after a system crash or power outage.

Starting with version 5.1.1.0 of Tivoli Storage Productivity Center for Replication, the
consistency group option is transparently implemented in all the FlashCopy session.

Figure 4-25 shows the Tivoli Storage Productivity Center for Replication console window in
which messages are reported that are related to a FlashCopy session. As highlighted, a
message of releasing the I/O is reported, which states that a freeze/unfreeze operation was
performed against the volumes within the session.

Figure 4-25 FlashCopy session console messages

There is no means of disabling the consistency group option for the FlashCopy sessions.

Note: The consistency group option applies only to the FlashCopy type session. All the
other sessions that use FlashCopy to create practice copy do not use this option.

4.2.2 Global Mirror pause with consistency

The Global Mirror pause with consistency is a capability that can be requested by submitting
a SCORE/RPQ to IBM for the microcode level 6.3.1 for DS8700 and DS8800, and level 7.0.5
for DS8870. By using this capability, the Global Mirror can be paused, which leaves the
Global Mirror secondary site volumes in a consistent state. Specifying this new option in the
Global Mirror pause command, the Global Mirror first completes the ongoing consistency
group. After it is hardened on the journal volumes, all the Global Copy pairs are suspended,
which does not allow any further update from the primary storage systems.

The Global Mirror pausing consistently allows several Tivoli Storage Productivity Center for
Replication sessions to use the function and speed up the time it takes to perform some
operations. This Global Mirror pausing option spares any further action to make the Global
Mirror secondary site volumes consistent. The standard recovery process, which involves the
consistency group checking and Fast Reverse Restore FlashCopy, is still needed for all the
planned and unplanned Global Mirror scenarios in which the Global Mirror was not paused
with the proper “with consistency” option.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 183
 Tivoli Storage Productivity Center for Replication uses the Global Mirror pause command
whenever a Suspend of a Global Mirror (or Global Mirror leg in the case of Metro Global
Mirror session) is started. Starting with Tivoli Storage Productivity Center for Replication
version 5.2, the Global Mirror pause with consistency option is transparently used for those
storage systems that fulfill the microcode requirements. Figure 4-26 and Figure 4-27 show
the report of the session details of a Global Mirror FO/FB session where a suspend command
was issued and the Pause with consistency option was used by Tivoli Storage Productivity
Center for Replication.

Figure 4-26 Session Details window after a Suspend command

The Role Pairs Info tab (see Figure 4-26) shows that H1 - H2 Global Copy pairs are already
recoverable with a time stamp that is the same of the consistency group that was hardened
on the journal.

Figure 4-27 Global Mirror Info tab after a Suspend command

In the Global Mirror Info tab (see Figure 4-27), a Paused with secondary consistency state is
reported.

184 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: There is no means of disabling the Pause with consistency option for the Tivoli
Storage Productivity Center for Replication sessions. The Tivoli Storage Productivity
Center for Replication always uses this option following a Global Mirror suspend command.

4.2.3 Easy Tier Heat Map Transfer

The IBM System Storage DS8000 Easy Tier heat map transfer function transfers heat map
information from a source storage system to one or more target storage systems. Each target
storage system then generates volume migration plans that are based on the heat map data
and the physical configuration of the storage system.

This process ensures that the performance characteristics of the target storage systems are
consistently updated to reflect the performance characteristics of the source storage system.
The Easy Tier heat map transfer function is available for System Storage DS8000 Release
7.1 and later.

IBM Tivoli Storage Productivity Center for Replication supports the DS8000 Easy Tier heat
map transfer function with version 5.1.1.1 or higher. The storage systems must meet the
following requirements:
򐂰 The source and target storage systems must be connected to Tivoli Storage Productivity
Center for Replication by using a Hardware Management Console (HMC) connection.
򐂰 The Easy Tier heat map transfer function must be enabled on the source and target
storage systems.

To support the Easy Tier heat map transfer function, another software component is installed
simultaneously to Tivoli Storage Productivity Center for Replication. This component, which is
called Heat Map Transfer Utility (HMTU), operates as a daemon that is running on the Tivoli
Storage Productivity Center for Replication server and performs the following actions:
򐂰 Loads storage system configuration information
򐂰 Pulls heat maps from the source storage system
򐂰 Applies source heat maps on the target storage system
򐂰 Records the heat maps transfer results

All of the Easy Tier heat map transfer-related tasks are performed by the HMTU. By using its
web-based GUI, Tivoli Storage Productivity Center for Replication offers an effective user
interface to configure the HTMU.

For more information about Easy Tier heat map transfer, see IBM System Storage DS8000
Easy Tier Heat Map Transfer, REDP-5015.

In the following sections, the HMTU main configuration steps through the Tivoli Storage
Productivity Center for Replication web-based GUI are described.

Adding a storage system to HMTU

Before a DS8000 storage system is added to HMTU, you must verify whether the Heat Map
Transfer function is enabled on the box. For this purpose, the showsi DSCLI command can be
used, as shown in Example 4-1 on page 186.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 185
 Example 4-1 Showsi command to verify the Easy Tier settings
dscli> showsi IBM.2107-75XC891
Name -
desc -
ID IBM.2107-75XC891
Storage Unit IBM.2107-75XC890
Model 961
WWNN 5005076303FFD414
Signature 6641-eccc-7ca9-7c1a
State Online
ESSNet Enabled
Volume Group V0
os400Serial 414
NVS Memory 2.0 GB
Cache Memory 48.7 GB
Processor Memory 62.2 GB
MTS IBM.2421-75XC890
numegsupported 1
ETAutoMode all
ETMonitor all
IOPMmode Managed
ETCCMode Disabled
ETHMTMode Enabled

The ETHMTMode setting reports the status of the Heat Map Transfer function. The scope of
Easy Tier Heat Map Transfer is determined by the following Easy Tier automatic mode
settings:
򐂰 With ETAutoMode set to tiered and ETMonitor set to automode, Heat Map Transfer and
data placement occurs for logical volumes in multi-tiered pools only.
򐂰 With ETAutoMode set to all and ETMonitor set to all, Heat Map Transfer and data
placement occurs for logical volumes in all pools.

To change the Easy Tier settings, including the Heat Map Transfer, you can use the chsi
DSCLI command, as shown in Example 4-2.

Example 4-2 Enabling Heat Map Transfer function

dscli> chsi -ethmtmode enable IBM.2107-75XC891
CMUC00042I chsi: Storage image IBM.2107-75XC891 successfully modified.

Tip: If you do not have Easy Tier activated and want to run an Easy Tier evaluation on the
primary and secondary storage systems, you can set the Easy Tier control on the primary
and secondary storage systems to monitor only (-etmonitor all). The heat map transfer
utility then automatically transfers the heat map data and uses this data to generate an
Easy Tier report, without changing the data layout on either of the storage systems.

Log on to the Tivoli Storage Productivity Center for Replication GUI to start the DS8000
adding procedure. Complete the following steps:
1. From the Health Overview window, access the Storage Systems panel through one of the
available links, as shown in Figure 4-28 on page 187.

186 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-28 Health Overview window

2. On the Storage Systems panel, click the Easy Tier Heat Map Transfer tab, then click Add
Storage System, as shown in Figure 4-29.

Figure 4-29 Adding storage system

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 187
 3. Select the Storage Systems to be included on the HMTU, as shown in Figure 4-30. Click
Add Storage Subsystems.

Figure 4-30 Storage System selection

Note: In the Add Storage System to Easy Heat Map Transfer panel, Tivoli Storage
Productivity Center for Replication shows only the storage systems with the Heat Map
Transfer function internally enabled.

4. After the storage systems are included in HMTU, all of the systems are presented with
inactive connection status. Select which storage system must have the transfer enabled
first and then click Enable Transfer, as shown in Figure 4-31.

Figure 4-31 Enabling map transfer

5. Click Yes in the confirmation panel to complete the operation, as shown in Figure 4-32.

Figure 4-32 Enable Transfer confirmation panel

188 Tivoli Storage Productivity Center for Replication for Open Systems
Checking the transfer status
To check the transfer status and validate when the latest transfer occurred, you can use two
different processes: click Select Action and then select View Transfer Status, or click the
paired storage systems, as shown in Figure 4-33.

Figure 4-33 View Transfer status

Statistics and some other information about the latest transfer are reported in the Transfer
Results panel, as shown in Figure 4-34.

Figure 4-34 Transfer results

Removing a storage system from HMTU

To remove a storage system from the HMTU configuration, complete the following steps:
1. From the Easy Tier Heat Map Transfer tab, select the storage system to be removed and
then click Disable Transfer to stop transfer processes, as shown in Figure 4-35.

Figure 4-35 Disabling Heat Map transfer

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 189
 2. Click Yes in the confirmation panel, as shown in Figure 4-36.

Figure 4-36 Disable transfer confirmation panel

3. Select the storage system to be removed and then click Remove Storage System from
the Select Action drop-down menu, as shown in Figure 4-37.

Figure 4-37 Removing Storage System

4. Click Yes in the confirmation panel to completely remove the storage system from the
HMTU configuration, as shown in Figure 4-38.

Figure 4-38 Remove Storage System confirmation panel

Important: When you enable or disable the use of the Easy Tier heat map transfer function
in Tivoli Storage Productivity Center for Replication, the function is not enabled or disabled
on the storage systems that are connected to Tivoli Storage Productivity Center for
Replication. The configuration options that you set for Easy Tier heat map transfer in Tivoli
Storage Productivity Center for Replication are used only by Tivoli Storage Productivity
Center for Replication.

190 Tivoli Storage Productivity Center for Replication for Open Systems
4.2.4 Global Mirror Info Tab for DS8000 sessions
Tivoli Storage Productivity Center for Replication Version 4.2 introduced a specific
informational tab in the Session Details panel (see Figure 4-39), which provides useful
information and details about the Global Mirror status. The following Global Mirror information
was made available:
򐂰 Data exposure information
򐂰 Current Global Mirror settings
򐂰 Statistics of successful and unsuccessful consistency groups

Figure 4-39 Global Mirror Info tab in Session Details panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 191
 Some of this information is available at a glance directly from the Role Pairs Info tab in the
Session Detail panel, as shown in the Figure 4-40.

Figure 4-40 Global Mirror session info at a glance

Selecting the Global Mirror Info tab (see Figure 4-39 on page 191) shows more information.
On the left side of the tab, the following information about the current Global Mirror status is
reported, as shown in Figure 4-41 on page 193:
򐂰 Global Mirror master logical subsystem (LSS)
򐂰 Master Consistency group time
򐂰 Master time during last query
򐂰 Data exposure time
򐂰 Session ID
򐂰 Master State
򐂰 Unsuccessful consistency groups (CGs) during last formation
򐂰 CG interval time
򐂰 Max Coordination time
򐂰 Max CG drain time
򐂰 List of subordinates (if any)

192 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-41 Global Mirror status information

An expandable section is reported whenever there is unsuccessful CG information that was

encountered since the start of the session. In this case, the following information is shown for
the last, previous, and first unsuccessful CG:
򐂰 Failing LSS
򐂰 Error reason
򐂰 Master state

On the right side of the tab, the Data Exposure graph is shown, as shown in Figure 4-42 on
page 194. The Data Exposure graph shows the instant Recovery Point Objective (RPO) trend
for the last 24 hours or the last 15 minutes. You can set up a data exposure threshold, which
highlights unusual spikes.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 193
 Figure 4-42 Data Exposure graph

Moving the mouse over the bullets in the graph, a callout appears which shows that the data
exposure exceeded the threshold, as shown in Figure 4-43.

Figure 4-43 Data exposure exceeded

194 Tivoli Storage Productivity Center for Replication for Open Systems
4.2.5 Global Mirror Historical Data
Starting with Tivoli Storage Productivity Center for Replication version 5.1, the Global Mirror
historical data is available to be exported in comma-separated value (CSV) file format. Export
can create the following types of CSV files:
򐂰 A file that contains data about the RPO
򐂰 A file that contains data about the logical subsystem (LSS) out-of-sync tracks

The data in the CSV file can be used to analyze trends in your storage environment that affect
your RPO.

Note: There is a Global Mirror Reporting Tool that is not included with the product.
However, it is available for use and includes a pre-setup spreadsheet for customers to
import data into, and can be downloaded from this website:
http://www-01.ibm.com/support/docview.wss?uid=swg21609629

Exporting the data

To export the Global Mirror historical data, you can click Export Global Mirror Data on the
Global Mirror tab (see Figure 4-42 on page 194) or click Export Global Mirror Data from the
drop-down menu in the Session Detail panel, as shown in Figure 4-44.

Figure 4-44 Export Global Mirror Data

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 195
 The Export Historical Data for Global Mirror wizard is displayed, as shown in Figure 4-45.

Figure 4-45 Export Historical Data wizard

The following information is required to complete the export:

򐂰 The role pair for the data that you want to show in the CSV file. Multiple role pairs are
available for Metro Global Mirror sessions and for Global Mirror Either Direction session.
򐂰 The type of data that you want to export to a CSV file. Depending on the data type that you
select, the CSV file contains data about the RPO or data about LSS out-of-sync tracks.
򐂰 The date range for the data that you want to show in the export file. The date range
maximum for RPO files is 31 days of data and the maximum for LSS out-of-sync track files
is seven days of data.

196 Tivoli Storage Productivity Center for Replication for Open Systems
Click Next. If the export was successful, a link to the CSV file is provided on the Results page,
as shown in Figure 4-46. The CSV file now can be saved to your local system.

Figure 4-46 Historical Global Mirror data export results panel

Using the data

Tivoli Storage Productivity Center for Replication provides the Global Mirror historical data in
the CSV file format that can be imported in a spreadsheet. The layout of the two files is fixed
and contains the fields that are shown in Table 4-2 on page 198 and Table 4-3 on page 199.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 197
 Table 4-2 RPO data file layout
Column Name Description

A Query Time Query sample time as reported by the Tivoli Storage

Productivity Center for Replication server.

B Hardware Time Time that is reported internally by the Master system.

Can be different from the Query Time because Master
System time and Tivoli Storage Productivity Center for
Replication server time might not be aligned.

C Interval Sample interval in seconds.

D Master Session Number Global Mirror session number. The format is 0xn where
n is the session number.

E Master Box Name Serial number of the Master system. The format that is
used is 2107.XXXXX, where XXXXX is the storage
image serial number.

F Master LSS Global Mirror master Logical Subsystem. The format is

0xnn, where nn is the LSS number.

G Master State Status of the Global Mirror Master.

H Last Consistency Group Last consistency group formation time as reported by

Formation Time the Master system.

I Average RPO Calculated average RPO for the last sample in

milliseconds.

J RPO at Time of Last Query Instant RPO at the last query in milliseconds. This is the
difference between the Hardware Time and the Last
Consistency Group Formation Time.

K Successful Consistency Number of successful consistency groups that are

Groups in Interval formed in the last sample interval.

L Number Failed Consistency Number of unsuccessful consistency groups that are

Groups in Interval formed in the last sample interval.

M Number Failed Consistency Number of unsuccessful consistency groups that are

Groups Since Last Successful formed in a row.

N Total LSSs Total number of LSSs that are defined to the Global
Mirror session.

O Total Out of Sync Tracks Total number of Out of Sync Tracks that are calculated
at the query time.

P Total Joined Total number of volumes that joined the Global Mirror
session.

Q Total Suspended Total number of volumes that were suspended in the

Global Mirror session (joined or in join pending).

R Most Recent Consistency Error that is reported for the last unsuccessful
Group Error consistency group formation.

S Most Recent Consistency Global Mirror state at the time of the last unsuccessful
Group Error State consistency group formation.

198 Tivoli Storage Productivity Center for Replication for Open Systems
Table 4-3 LSS out-of-sync tracks file layout
Column Name Description

A Query Time Query sample time as reported by the Tivoli Storage Productivity
Center for Replication server.

B Hardware Time Time that is reported internally by the system (can be the Master
or a subordinate system). Can be different from the Query Time
because the hardware time and Tivoli Storage Productivity
Center for Replication server time might not be aligned.

C Interval Sample interval.

D Session Number Global Mirror session number. The format is 0xn, where n is the
session number.

E Box Name Serial number of the system (can be the Master or a subordinate
system). The format is 2107.XXXXX, where XXXXX is the
storage image serial number.

F LSS LSS queried. The format is 0xnn, where nn is the LSS number.

G Out Of Sync Tracks Total number of the out-of-sync tracks for the queried LSS.

A five-row header, which is common for both CSV files, is automatically created that reports
general information about the file. A sample of this header for an RPO data file is reported in
Figure 4-47.

#Generated at:,5/15/2013 12:26

#Session Name:,MGM_ITSO
#Role Pair:,H2-J3
#Start Date:,9-May-13
#End Date:,15-May-13

<statistics data here>

Figure 4-47 RPO data file header

The CSV file format is suitable to be processed by using a spreadsheet application. By using
pivot tables or a similar feature, you can sort or aggregate the data to obtain more usable
information that can be used for performance tuning or problem determination purposes.
Also, by using the spreadsheet chart feature, you can create a graph for historical trend
information, as shown in Figure 4-48 on page 200. You can also create a punctual interval
analysis, as shown in Figure 4-49 on page 200.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 199
Figure 4-48 Historical RPO chart

Figure 4-49 Out of Sync Tracks versus LSS chart

200 Tivoli Storage Productivity Center for Replication for Open Systems
4.2.6 Managing z/OS HyperSwap from Tivoli Storage Productivity Center for
Replication for Open Systems
Tivoli Storage Productivity Center for Replication for Open Systems version 5.2 can manage
z/OS HyperSwap enabled sessions through an IP connection to a z/OS server. For more
information, see Chapter 7, “Managing z/OS HyperSwap from Tivoli Storage Productivity
Center for Replication for Open Systems” on page 355.

4.3 Managing DS8000 sessions

As described in 4.1, “Capabilities overview” on page 160, Tivoli Storage Productivity Center
for Replication support many types of DS8000 replication topologies that combine various
copy services features. In the following sections, we describe how to set up and manage
replication sessions. We summarize the tunable parameters for every session that is
supported and describe some scenarios that require a full copy of data.

4.3.1 DS8000 Path management

Before we start to operate with a DS8000 session, we must properly define the replication
connectivity schema to implement. This involves managing the logical paths.

The logical paths define the relationship between a source LSS and a target LSS that is
created over a physical path (IO port).

Tivoli Storage Productivity Center for Replication includes the Path Manager feature to
provide control of logical paths when relationships between source and target storage
systems are established.

Path Manager helps you control the port pairing that Tivoli Storage Productivity Center for
Replication uses when the logical paths are established and ensure redundant port
combinations. It also keeps that information persistent for use when the path is terminated
because of a suspended operation.

Tivoli Storage Productivity Center for Replication provides you the following options to create
the logical paths and specify port pairing:
򐂰 Adding logical paths automatically, Tivoli Storage Productivity Center for Replication
automatically picks the paths or uses paths that were established.
򐂰 Adding logical paths and creating port pairing by using a CSV file.
򐂰 Adding logical paths by using Tivoli Storage Productivity Center for Replication GUI.

Adding logical paths automatically

If you do not specify the port pairing, Tivoli Storage Productivity Center for Replication queries
the storage systems to check whether there are established paths. By using the CSV file, you
can ensure redundant port combinations and use only the specified ports. If at least one path
is established, Tivoli Storage Productivity Center for Replication uses that path and it does not
create more paths. Otherwise, if no path is established, Tivoli Storage Productivity Center for
Replication queries the storage systems to pick the available ports (if any) to create a path. In
this case, Tivoli Storage Productivity Center for Replication creates only one path per LSSs
pair.

Note: This option does not ensure that you have redundant logical paths.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 201
 Adding logical paths by using a CSV file
You can add logical paths by creating a CSV file. The CSV file specifies storage systems
pairings and associated port pairings that are used by Tivoli Storage Productivity Center for
Replication to establish the logical paths. By using the CSV file, you can ensure redundant
port combinations and use only the specified ports. Tivoli Storage Productivity Center for
Replication uses the ports that are listed in the CSV file when you run the start command
(that is, Start H1 → H2) and attempts to establish the paths between any LSS on those two
storage systems.

To add logical paths by using a CSV file, complete the following steps:
1. Create a CSV file that is named portpairings.csv in the
install_root/IBM/TPC/wlp/usr/servers/replicationServer/properties directory.

Note: In the install_root/IBM/TPC/wlp/usr/servers/replicationServer/properties

directory, you find the portpairings.csv.sample file, which you can use and rename to
portpairings.csv

An example of a CSV file is shown in Example 4-3.

Example 4-3 Sample of portpairings.csv file

#Primaries ---> Secondaries
2107.ALD71:2107.ANZ41,0x0002:0x0002,0x0006:0x0006,0x0132:0x0132,0x0136:0x0136
2107.ACD21:2107.ALZ61,0x0002:0x0002,0x0006:0x0006,0x0132:0x0132,0x0136:0x0136

#Secondaries ---> Tertiaries

2107.ANZ41:2107.YX531,0x0231:0x0003,0x0206:0x0233,0x0005:0x0001,0x0235:0x0101
2107.ALZ61:2107.AXG11,0x0102:0x0333,0x0206:0x0233,0x0035:0x0001,0x0305:0x0131

#Primaries ---> Tertiaries

2107.ALD71:2107.YX531,0x0231:0x0003,0x0131:0x0233,0x0232:0x0232,0x0236:0x0236
2107.ACD21:2107.AXG11,0x0331:0x0333,0x0031:0x0233,0x0232:0x0232,0x0236:0x0236

Each line in the file represents a storage system-to-storage system pairing. The first value
represents the storage systems, which are delimited by a colon. The remaining values are
the port pairs, which are delimited by a colon. All values are separated by a comma and
commented lines must start with # character. The following roles must be followed when
the CSV port pairings are used:
– The entry for a storage system pair and the port pairs are bidirectional. This means
that a line that has systemA:systemB is equivalent to a line that has systemB:systemA.
Lines that are incorrectly formatted are discarded. For example, if a line contains ports
without the 0x, or does not contain port pairs that are delimited by the : character, the
entire line is discarded.
– A line can be properly formatted but contain invalid ports for your storage system
configuration. In this case, the ports are passed down to the storage system to be
established and there is no validation that is done in Tivoli Storage Productivity Center
for Replication. The valid ports might be established by the storage system, while the
invalid ports can be rejected.
– If a file contains duplicate lines for the same storage systems, the ports on the last line
are used. Also, the entries are bidirectional. Thus, if you have systemA:systemB and
then a line with systemB:systemA, the second line is the line that is used.

202 Tivoli Storage Productivity Center for Replication for Open Systems
 – Any line that starts with a # character is considered a comment and is discarded. The
# must be at the start of the line. Placing it in other positions can cause the line to be
invalid.
– The portpairings.csv is not shared between two Tivoli Storage Productivity Center for
Replication servers in a high-availability environment. Thus, different port pairings can
be established from the standby server after a takeover. You must copy the
portpairings.csv file to the standby server to ensure that the two files are equal.
2. To enable the changes in the file, you must perform a task that requires new paths to be
established. For example, suspend a session to remove the logical paths and then issue
the Start H1 → H2 command to enable the paths to use the port pairings in the CSV file.

Note: By enabling the CSV file port pairing, you cannot differentiate LSS logical paths
definitions within a storage systems pairing. If you must use different port pairings among
LSSs within the same storage systems pairing, you must not use the portpairings.csv
file.

Adding logical paths by using Tivoli Storage Productivity Center for

Replication GUI
You can add logical paths by using the Tivoli Storage Productivity Center for Replication GUI.
In this section, we describe how to add the logical paths. Before you add the paths, you must
ensure that you defined the appropriate storage systems on the Storage Systems panel.

To add the logical paths, complete the following steps:

1. In the Tivoli Storage Productivity Center for Replication navigation tree, select ESS/DS
Paths. The panel in which you manage the paths opens, as shown in Figure 4-50.

Figure 4-50 Manage paths

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 203
 2. Click Manage Paths. The Path Management wizard opens, as shown in Figure 4-51.
From the drop-down menu in the wizard, select the source storage system, source logical
storage system, target storage system, and target logical storage system. Click Next.

Figure 4-51 Selecting Source and Target storage systems

3. From the drop-down menu in the wizard, select the source port and target port and click
Add. You can add multiple paths between the logical storage subsystems, or one at a
time. After you make your selections, click Next, as shown in Figure 4-52.

Figure 4-52 Adding ports

204 Tivoli Storage Productivity Center for Replication for Open Systems
4. Confirm your selections and click Next, as shown in Figure 4-53.

Figure 4-53 Confirm the paths

5. Verify the Results panel and click Finish to exit the wizard, as shown in Figure 4-54.

Figure 4-54 Results panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 205
 6. By clicking the Storage System, you see the path that were added, as shown in
Figure 4-55.

Figure 4-55 Managed paths

Logical Paths requirements and limitations

There are some considerations that are related to logical paths that we must remember when
we are planning the replication configuration.

Logical Paths requirements

PPRC technology requires at least one logical path per LSS pair to establish a mirroring
relationship. Tivoli Storage Productivity Center for Replication does not check the path’s
availability before starting a mirroring relationship. If no paths are available between two
DS8000s, this leads to an error at the first attempt to establish a pair relationship. Although
the physical Fibre Channel link is bidirectional, the logical path definition is not. Therefore, to
use the same port pair in both directions we must define a logical path in both storage
systems (for example, one from box A to B and another from box B to A).

If you are not using the CSV file to establish the paths (as described in section “Adding logical
paths by using a CSV file” on page 202), the following recommendations are important:
򐂰 Establish all the paths in both directions to avoid bandwidth limitations in the failback
operations.
򐂰 Provide connectivity and path definitions from the local to remote site and vice versa for
the three site session types. This is because many operations in a Metro Global Mirror
configuration require a full interconnection among the three sites.

Logical Paths limitations

The following limitations apply to logical paths:
򐂰 Maximum number of logical paths per LSS pair is 8.
򐂰 Maximum number of LSS pairs per source LSS is 4.

Note: These limitations might change in future releases and are the supported limits at the
time of this writing.

206 Tivoli Storage Productivity Center for Replication for Open Systems
Give specific attention to the second limitation in the case of asymmetrical pairings of LSSs.
For example, consider the configuration that is shown in Figure 4-56.

Figure 4-56 Metro Global Mirror with asymmetric LSS pairing configuration

In this configuration, LSS pairings are not symmetrical for the Global Mirror because volumes
that belong to LSS 20 are replicated in LSS 30, 31, 32, and 33. During the normal Metro
Global Mirror operations, this LSS pairing does not create problems. However, consider a
scenario in which a Failover/Failback operation is required for volumes on the intermediate
site (that is, Metro Mirror secondary volumes). This is a typical switch site scenario that can
be managed through Tivoli Storage Productivity Center for Replication by following the
transition diagram that is shown in Figure 4-57 on page 208.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 207
 Figure 4-57 State transition diagram

In this example, when the Failback operation is performed, Tivoli Storage Productivity Center
for Replication attempts to establish one path between LSS 20 in Site 2 and LSS 10 in Site 1.
However, because there are four LSS pairs from LSS 20 still defined (even if they not used), it
fails, as shown in Figure 4-58 on page 209.

208 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-58 Failed Failover operation

4.3.2 Setting up a session

In this section, the setup process for a sample session is described. Consider that the
process of defining a session is about the same for all the DS8000 session types. Only the
number of volumes that define a copy sets and the session parameters (see 4.3.3, “Session
tunable parameters” on page 230) are different among the session types. For this reason, the
processes in this section can be used to define virtually any type of DS8000 session.

Creating Metro Mirror Failover/Failback with Practice session

Log on the Tivoli Storage Productivity Center for Replication GUI interface to start the session
creating process. Complete the following steps:
1. From the Health Overview window, open the Session panel by using one of the available
links, as shown in Figure 4-59 on page 210.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 209
Figure 4-59 Health Overview panel with the Session links

2. In the Session panel, click Create Session, as shown in Figure 4-60.

Figure 4-60 Session panel

3. The Create Session panel opens. From the Choose Hardware Type drop-down menu,
select DS8000, DS6000, ESS800, as shown in Figure 4-61 on page 211.

210 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-61 Choose Hardware Type menu

4. From the Choose Session Type drop-down menu, select Metro Mirror Failover/Failback
w/ Practice, as shown in Figure 4-62.

Figure 4-62 Choose Session Type menu

5. Click Next to go to the Session Properties panel. The Properties panel requires that you
specify at least a name for the session, which is about to be created (valid characters for
the session name are: A-Z, a-z, 0-9, ',', '-', '.', ' ', '_'). An optional Description is
recommended to understand the purpose of the session because the session name might
not indicate the purpose of the session. Possible session-specific tunable parameters also
must be set in this panel. Figure 4-63 on page 212 shows the setting for this sample.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 211
 Figure 4-63 Session Properties panel

6. Click Next to go to the Site Locations panel. Because the Metro Mirror Failover/Failback
with Practice session type is a two-site replication topology, two location sites must be
specified. From the drop-down menu, select the Site 1 location, as shown in Figure 4-64.

Figure 4-64 Site Location Panels for Site 1

212 Tivoli Storage Productivity Center for Replication for Open Systems
7. Click Next to define the Site 2 location, as shown in Figure 4-65.

Figure 4-65 Site Location Panels for Site 2

8. Click Next to see the results of the session creation, as shown in Figure 4-66.

Figure 4-66 Create session Results panel

9. Click Finish to close the Create Session wizard or Launch Add Copy Sets Wizard to add
copy sets in this session.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 213
 After the session is created, the Session panel shows the new session in Inactive status, as
shown in Figure 4-67.

Figure 4-67 Session panel showing the new session

Complete the following steps to add the copy sets to the session:
1. To start the Add Copy Set wizard, use one of the following methods:
– Click Launch Add Copy Sets Wizard in the Create session wizard, as shown in
Figure 4-66 on page 213.
– Select the radio button of the session name in the main Session panel and then click
Add Copy Set from the drop-down menu.
– Click the session name in the main Session panel, and then click Add Copy Set from
the drop-down menu in the Session Detail panel.
The Add Copy Set wizard opens, as shown in Figure 4-68. The Metro Mirror
Failover/Failback with Practice session is a two-site replication topology with each copy
sets formed by the following volumes:
– H1 volume for the host volume in site 1. This is Metro Mirror primary volume.
– H2 volume for the host volume in site 2. This is the practice FlashCopy target volume.
– i2 volumes for the intermediate volume in site 2. This is Metro Mirror secondary
volume.
As shown in Figure 4-68 on page 215, you must specify the storage system (#1 in the
figure), the Logical Subsystem (#2 in the figure), and Volume ID (#3 in the figure) for each
volume within the copy set. This process always starts with the H1 volumes.

214 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-68 Host 1 volume selection

After the volume selection (see Figure 4-68) is completed, the volume details are reported
on the right side of the panel. In the select volume drop down-menu, you can select all of
the volumes that belong to the LSS that was selected. You can define more copy sets at
once. In this case, the selection of the copy set to be added definitively to the session can
be refined later.

Important: The intermix of volumes with different sizes or space allocation methods
(standard or ESE) within the same copy set is not allowed. The characteristics of H1
volumes determine the characteristics of the remaining volumes in the copy sets. For
example, if the H1 volume is a 10 GB Extent Space Efficient volume, all the other
volumes within the copy sets must have the 10 GB size and ESE space allocation
method. For more information about TSE volumes usage as FlashCopy targets, see
4.1, “Capabilities overview” on page 160.

2. Click Next to go the H2 volume selection panel, as shown in Figure 4-69 on page 216.
The Host 2 volume selection drop-down menu shows only one volume candidate because
it is the only one in the selected storage system and LSS that has the same characteristics
of the H1 volume.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 215
 Figure 4-69 Host 2 volume selection

3. Click Next and complete the copy set definition by selecting the i2 volume, as shown in
Figure 4-70.

Figure 4-70 Intermediate 2 volume selection

4. When the volume selection for the copy set is completed, click Next to start the matching
process. After the matching process is completed, the Select Copy Sets panel opens, as
shown in Figure 4-71 on page 217.

216 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-71 Select Copy Set panel

By clicking Add More, more copy sets can be added to the session by using the same
process. When all of the copy sets are defined, you select the copy set to add to the
session and click Next to continue.
5. The wizard prompts you to confirm your configuration, as shown in Figure 4-72. Click
Next.

Figure 4-72 Add copy sets confirmation panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 217
 When the Copy Set is added successfully, click Finish, as shown in Figure 4-73.

Figure 4-73 Add copy sets results panel

If you have a large configuration to define to a session, this process can be laborious. In this
case, the Add Copy Set wizard provides the CSV file import feature that simplifies the copy
sets definition process. For more information, see “Importing CSV files” on page 132.

Managing a session
After we define a session and populate the session with Copy Sets, we can start managing
the replication through Tivoli Storage Productivity Center for Replication. Again, the process
of managing a session is about the same for all the DS8000 session types. So, the basic
concepts we describe in this section apply to almost all of the session types.

In this section, we describe how to use the Tivoli Storage Productivity Center for Replication
GUI to manage the Metro Mirror Failover/Failback with Practice session that was previously
defined in some actual situations.

First, we describe a normal operation scenario in which the following actions are performed:
1. Start the Metro Mirror.
2. Run a FlashCopy to create practice volumes for Disaster Recovery testing.

The flow of the operation is shown in Figure 4-74 on page 219.

218 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-74 State transition diagram for first scenario

We then consider a scenario of planned outage of the primary site. In this case, the process
can be used:
1. Suspend the Metro Mirror.
2. Recover the Metro Mirror secondary volumes.
3. Start the Metro Mirror from Site 2 site to Site 1.

The flow of the operations for this second scenario is shown in Figure 4-75.

Figure 4-75 State transition diagram for second scenario

Starting the Metro Mirror

Figure 4-76 on page 220 shows the ITSO-MM-FOFB-wP session as we defined it. We
defined only one copy set in our example. Because this is Failover/Failback type of a session,
it can be started in direction from Host 1 to Host 2 and in direction from Host 2 to Host 1.
Initially, the session can be started only in direction from Host 1 to Host 2. To start it, from the
drop-down menu, select Start H1 → H2 and then click Go.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 219
Figure 4-76 Start Metro Mirror

The message that is shown in Figure 4-77 is a warning that you are about to start a Metro
Mirror session. It starts copying the data from Host 1 to Intermediate 2 volumes that were
defined by adding copy sets, which overwrite any data on Intermediate 2 volumes. At this
stage, data on Host 2 volumes is not yet overwritten.

Figure 4-77 Start H1 → H2 confirmation panel

Click Yes to continue.

220 Tivoli Storage Productivity Center for Replication for Open Systems
 In Figure 4-78, the session details are shown after the Metro Mirror is started. We can find the
following information:
1. At the top of the panel is a message that confirms that start of Metro Mirror session is
complete.
2. The status of the session is shown in the middle of the panel. The session is in Preparing
state and Warning status because the copying is still in progress.
3. The Detailed Status field shows the current action Tivoli Storage Productivity Center for
Replication is performing.
4. The progress bar shows the copy progress for the Metro Mirror (it shows 0% because the
copy is started).

Also, the Non-Participating Role Pairs are shown at the bottom of the panel. Non-Participating
Role Pairs are role pairs that are not involved in any replication activity, but can become active
during specific configurations of the session.

Figure 4-78 Session Details panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 221
 After the initial copy is completed, the session goes to Normal status and Prepared state, as
shown in Figure 4-79.

Figure 4-79 Session Details showing the session in Normal status

The following actions are now available:

򐂰 Flash
򐂰 Start H1 → H2
򐂰 StartGC H1 → H2
򐂰 Stop
򐂰 Suspend

Flashing the session

Now that the volumes of the session are synchronized, we can start different actions against
the Metro Mirror session. One of these actions is Flash. By using the Flash action, you can
create a consistent copy of i2 volumes on H2 volumes and overwrite data on Host 2 volumes.
From the Sessions Details panel, select Flash from the drop-down list and click Go, as shown
in Figure 4-80 on page 223.

222 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-80 Session Details panel showing the Flash action

A confirmation panel opens. Click Yes to continue. The Flash command is used to create a
consistent point in time copy of H1 volumes to the H2 volumes for test purposes. This is
achieved completing the following steps:
1. Run a Metro Mirror Freeze/Unfreeze command to bring the i2 volumes in consistent state.
2. Establish the FlashCopy to H2 volumes.
3. Restart the Metro Mirror.

All of these actions are reported in the console log, as shows Figure 4-81.

Figure 4-81 Console log

The status of the Metro Mirror session briefly changed to Warning status while the
resynchronization process was active. After the copy is completed, the session status is
returned to Normal. In Figure 4-82 on page 224, you can see the session details after the
Flash action was performed.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 223
Figure 4-82 Session Details panel showing the Flash action results

In the row that lists the H2-I2 pair (see Figure 4-82), you can see the time stamp when the
point in time copy was created. This can be used as a reference.

After the Flash action completes, you can start using the Host 2 volumes. The point in time
copy is created with the background copy option and the progress bar for H2-I2 role pair
shows the percentage of copied data.

You can use Flash action any time in the life span of the session.

Suspending the session

After the volumes of the session are synchronized, we can start the Suspend action. From the
Sessions Details panel, select Suspend from the drop-down menu and click Go, as shown in
Figure 4-83 on page 225.

224 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-83 Session Details panel showing the Suspend action

Confirm the action in the next panel to continue. The Suspend command is used to create a
consistent copy of the secondary volumes. This is achieved issuing a Metro Mirror Freeze.

The status of our Metro Mirror session, as shown in Figure 4-84, changed from Normal to
Severe status, which indicates that data is no longer replicated between Host 1 and Host 2
volumes. The volumes in H1-I2 role pair are in recoverable (that is, consistent) status.

Figure 4-84 Session Details panel showing the Suspend action results

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 225
 After the Metro Mirror session is suspended, the following actions are available:
򐂰 Recover
򐂰 Start H1 → H2
򐂰 StartGC H1 → H2

Recovering the session

After the Metro Mirror session and its associated copy sets are suspended, we can start the
secondary volumes recovery process by selecting Recover from the drop-down menu, as
shown in Figure 4-85. Click Go to continue.

Figure 4-85 Session Details panel showing the Recover action

Confirm the action in the next panel to continue. The Recover command is used to make the
H2 volumes available for the host and ready to be copied back to the Site 1. This is achieved
by issuing multiple Metro Mirror Failover commands that establish Out of Sync Tracks bitmaps
on the i2 and H2 volumes. The Recover command also establishes a new FlashCopy to the
H2 volumes.

Important: The Recover command overwrites the content of the H2 volumes that are
issuing a FlashCopy from i2 to H2. Before you run the Recover command, make sure that
all the host activity on H2 volumes is stopped.

There is a message at the top of the window (as shown in Figure 4-86 on page 227) that
indicates that Recover action was successfully completed. The status of our Metro Mirror
session is Normal and the State is Target Available, which indicates that H2 volume is
available to your host. Also, the new FlashCopy was established between i2 and H2.

226 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-86 Session Details panel showing the Recover action results

After the Metro Mirror session is recovered in Target Available state, the following options are
available:
򐂰 Flash
򐂰 Start H1 → H2
򐂰 StartGC H1 → H2

There also is the option to switch the production site by selecting Enable Copy To Site 1.

Reversing the Metro Mirror

After the Recover action, Host 2 volumes are active. Because the Host 2 site is now the active
site, you can start copying from Host 2 to Host 1 volumes. To do this, from the drop-down
menu (as shown in Figure 4-86), select Enable Copy To Site 1 and then click Go. The panel
that is shown in Figure 4-87 warns that you are about enable commands with which you can
copy data to Site 1. Click Yes to proceed.

Figure 4-87 Enable Copy to Site 1 confirmation panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 227
 At this stage, data on Host 1 volumes is not yet overwritten, but the following actions are now
enabled:
򐂰 Flash
򐂰 Start H2 → H1
򐂰 StartGC H2 → H1

Select Start H2 → H1 and click Go, as shown in Figure 4-88.

Figure 4-88 Session Details panel showing the Start H2 → H1 action

Confirm the action in the next panel to continue. The Start H2 → H1 command is intended to
be used to switch the Metro Mirror direction temporarily when the host is working on Site 2. In
this case, the synchronization process from H2 to H1 volumes is incremental.

The message at the top of the window that is shown in Figure 4-89 on page 229 confirms that
start of Metro Mirror session is complete. The session is in Preparing state and Warning
status.

228 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-89 Session Details panel showing the Start H2 → H1 action results

After the resynchronization is complete, the session goes to Normal status and Prepared
state, as shown in Figure 4-90.

Figure 4-90 Session Details panel showing the session in Normal status

To return to the original configuration, the process is the same as described in “Recovering
the session” on page 226 and “Reversing the Metro Mirror” on page 227 where the role of H1
and H2 is reversed. A full copy from H1 to H2 is required in this case.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 229
4.3.3 Session tunable parameters
In this section, we describe the tunable parameters (session Options) for all of the session
types that are available for DS8000. All of these tunable parameters can be set during the
session definition (see 4.3.2, “Setting up a session” on page 209). Most of these parameters
can be modified later by changing the properties of the session.

To modify the options for a session, go to the Session main panel and select the session, as
shown in Figure 4-91.

Figure 4-91 Select the session in the main Session panel

From the drop-down menu, select View / Modify Properties and then click Go, as shown in
Figure 4-92 on page 231.

230 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-92 Select View / Modify Properties

From the View / Modify Properties panel, the session options can be modified, as shown in
Figure 4-93.

Figure 4-93 View / Modify Properties panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 231
 FlashCopy session tunable parameters
The FlashCopy session includes the following options:
򐂰 Incremental
Select this option to apply incremental changes to the target volume. After the initial
FlashCopy operation, only data that changed on the source volume since the last
FlashCopy operation was performed is copied to the target volume. If you select this
option, a persistent FlashCopy relationship is created regardless of whether you select the
Persistent option.
򐂰 Persistent
Select this option to keep the FlashCopy relationship established on the hardware after all
source tracks are copied to the target volume. If you do not select this option, the local
replication relationship ends after the target volume contains a complete point-in-time
image of the source volume
򐂰 No Copy
Select this option if you do not want the hardware to write the background copy until the
source track is written to. Data is not copied to the target volume until the blocks or tracks
of the source volume are modified. This option is required for space-efficient volumes.
򐂰 Allow FlashCopy target to be Metro Mirror source
Select this option to enable the FlashCopy operation if the target volume of the FlashCopy
relationship is also the source volume of a Metro Mirror relationship. If this option is not
selected, the FlashCopy operation fails. This option requires that the IBM Remote Pair
FlashCopy option is available for your IBM System Storage DS8000 storage system.
Select one of the following options to specify whether you want to maintain consistency, if
possible:
– Don't attempt to preserve Metro Mirror consistency
Click this option if you want the FlashCopy operation to complete without preserving
consistency of the Metro Mirror relationship on the remote site. The FlashCopy
operation does not occur on the remote site.
– Attempt to preserve Metro Mirror consistency but allow FlashCopy even if Metro Mirror
target consistency cannot be preserved
Click this option to preserve the consistency of the Metro Mirror relationship at the
target of the FlashCopy relationship when the source and target of the FlashCopy
relationship are the source of a Metro Mirror relationship. If the consistency cannot be
preserved, a full copy of the Metro Mirror relationship at the target of the FlashCopy
relationship is performed. To preserve consistency, parallel FlashCopy operations are
performed on both sites, if possible.
– Attempt to preserve Metro Mirror consistency but fail FlashCopy if Metro Mirror target
consistency cannot be preserved
Click this option to prevent a full copy from being performed over the Metro Mirror link.
Instead, parallel FlashCopy operations are performed on both sites, if possible. If the
consistency cannot be preserved, the flash for the FlashCopy relationships fails, and
the data of the Metro Mirror relationship at the target of the FlashCopy relationship is
not changed.

232 Tivoli Storage Productivity Center for Replication for Open Systems
Metro Mirror sessions tunable parameters
Different session options are available for the Metro Mirror session type, depending on the
topology of the session.

Metro Mirror Single Direction and Metro Mirror Failover/Failback

The following Metro Mirror options are available:
򐂰 Metro Mirror Suspend Policy options
Select one of the following options to specify the policy for holding or releasing
input/output (I/O) after a Metro Mirror relationship is suspended. When a relationship is in
a Suspended state, write operations from the source volume are no longer mirrored to the
target volume:
– Hold I/O after Suspend
Click this option to prevent the source volume from receiving new data after the
relationship is suspended. Use this option if you want to determine the scope of the
suspension before new data is written to the source volume. This option helps to
ensure that the data on the source and target volumes remains the same. To enable
write operations to the source volume to continue, issue the Tivoli Storage Productivity
Center for Replication Release I/O command for the session. If you do not issue this
command, write operations are enabled when the hardware timeout value on the
storage system expires.
– Release I/O after Suspend
Click this option to enable the source volume to automatically receive data after the
relationship is suspended. Use this option if you want to limit the affect on the
applications that are writing to the source volume. This option is enabled by default
򐂰 Fail MM/GC if target is online (CKD only)
Select this option to fail any session commands for a Metro Mirror or Global Copy
relationship if the target volume is in the Online state. For more information about this
state, see the documentation for the storage system. This option applies only to count key
data (CKD) volumes.
򐂰 Reset Secondary Reserves
Select this option to remove any persistent reserves that might be set on the target
volumes of the copy sets when a Start command is issued for the session.

Metro Mirror FO/FB with Practice

In addition to the options that were described for the Metro Mirror Failover/Failback (FO/FB)
session type (see “Metro Mirror Single Direction and Metro Mirror Failover/Failback” on
page 233), the Persistent FlashCopy option for Role Pair H2-I2 is available for the Metro
Mirror FO/FB with Practice session type. Select this option to keep FlashCopy pairs persistent
on the hardware.

Global Mirror sessions tunable parameters

Different session options are available for Global Mirror session types, depending on the
topology of the session.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 233
 Global Mirror Single Direction and Global Mirror FO/FB
For the Role Pair H1-J2, the following Global Mirror options are available:
򐂰 Consistency group interval time (seconds).
Enter how often, in seconds, the Global Mirror session attempts to form a consistency
group. A lower value can reduce the data exposure of the session. However, a lower value
also causes the session to attempt to create consistency groups more frequently, which
can increase network traffic. Possible values are 0 - 65535. The default is 0 seconds.

Global Mirror settings: In addition to the Consistency Group Interval Time, the
Maximum Coordination Interval Time and the Maximum Consistency Group Drain Time
are parameters that affect the Global Mirror behavior. By default, Tivoli Storage
Productivity Center for Replication establishes a Global Mirror session that uses the
default values for these two parameters. The default values are 50 (ms) for Maximum
Coordination Interval Time and 30 (seconds) for Maximum Consistency Group Drain
Time. These values are the recommended values that fit most of the Global Mirror
installations.

If a modification of these two parameters is required, this can be done only by using the
chsess CSMCLI command. Depending on the Role Pair that is involved and the session
type, different options are available for the chsess CSMCLI command to modify
Maximum Coordination Interval Time and the Maximum Consistency Group Drain Time
settings. For the Global Mirror Single Direction, Global Mirror Failover/Failback and
Global Mirror Failover/Failback with Practice session types you can use the following
commands:
򐂰 chsess -maxdrain xx NameSession to set to xx seconds the Maximum Consistency
Group Drain Time for the session NameSession
򐂰 chsess -coordint yy NameSession to set to yy milliseconds the Maximum
Coordination Interval Time

These settings require a Global Mirror session suspension.

򐂰 Recovery Point Objective Alerts

Specify the length of time that you want to set for the RPO thresholds. The values
determine whether a Warning or Severe alert is generated when the RPO threshold is
exceeded for a role pair. The RPO represents the length of time (in seconds) of data
exposure that is acceptable if a disaster occurs. Use the following options to set the RPO
threshold values. For both options, you can specify an RPO threshold in the range of 0 -
65535 seconds. The default is 0 seconds, which specifies that no alerts are generated:
– Warning level threshold (seconds).
Enter the number of seconds that you want to set for the warning level RPO threshold.
If the RPO is greater than this value, a warning console message is generated, an
SNMP trap is sent, and the session status changes to Warning. If the value in this field
is other than 0, it must be greater than the value in the Consistency group interval time
(seconds) field and less than the value in the Severe level threshold (seconds) field.
– Severe level threshold (seconds)
– Enter the number of seconds that you want to set for the severe level RPO threshold. If
the RPO is greater than this value, an error console message is generated, an SNMP
trap is sent, and the session status changes to Severe. If the value in this field is other
than 0, it must be greater than the value in the Warning level threshold (seconds) field.

234 Tivoli Storage Productivity Center for Replication for Open Systems
򐂰 Fail MM/GC if target is online (CKD only)
Select this option to fail any session commands for a Metro Mirror or Global Copy
relationship if the target volume is in the Online state. For more information about this
state, see the documentation for the storage system.
򐂰 Reset Secondary Reserves
Select this option to remove any persistent reserves that might be set on the target
volumes of the copy sets when a Start command is issued for the session.

Global Mirror FO/FB with Practice

In addition to the options that were described for the Global Mirror FO/FB session type (see
“Global Mirror Single Direction and Global Mirror FO/FB” on page 234), the following specific
FlashCopy Options for Role Pair H2-I2 are available for the Global Mirror FO/FB with Practice
session type:
򐂰 Persistent
Select this option to keep FlashCopy pairs persistent on the hardware.
򐂰 No Copy
Select this option if you do not want the hardware to write the background copy until the
source track is written to. Data is not copied to the H2 volume until the blocks or tracks of
the i2 volume are modified.

For the Role Pair I1-J2, the Reflash After Recovery FlashCopy option is available. Select this
option if you want to create a FlashCopy replication between the i2 and J2 volumes after the
recovery of a Global Mirror Failover/Failback with Practice session. If you do not select this
option, a FlashCopy replication is created between the i2 and H2 volumes only.

Global Mirror Either Direction with two Site Practice

For the Role Pair H1-J2, the following Global Mirror options are available:
򐂰 Consistency group interval time (seconds)
Enter how often, in seconds, the Global Mirror session attempts to form a consistency
group. A lower value can reduce the data exposure of the session. However, a lower value
also causes the session to attempt to create consistency groups more frequently, which
can increase network traffic. Possible values are 0 - 65535. The default is 0 seconds.

Global Mirrors settings: For the Global Mirror Either Direction with Two Site Practice
session type you can use the following commands:
򐂰 chsess -maxdrain_h1j2 xx NameSession to set to xx seconds the Maximum
Consistency Group Drain Time for the session NameSession for the Role Pair
H1-J2.
򐂰 chsess -coordint_h1j2 yy NameSession to set to yy milliseconds the Maximum
Coordination Interval Time for the Role Pair H1-J2.

These settings require a Global Mirror session suspension.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 235
 򐂰 Recovery Point Objective Alerts
Specify the length of time that you want to set for the RPO thresholds. The values
determine whether a Warning or Severe alert is generated when the RPO threshold is
exceeded for a role pair. The RPO represents the length of time (in seconds) of data
exposure that is acceptable if a disaster occurs. Use the following options to set the RPO
threshold values. For both options, you can specify an RPO threshold in the range of 0 -
65535 seconds. The default is 0 seconds, which specifies that no alerts are generated:
– Warning level threshold (seconds)
Enter the number of seconds that you want to set for the warning level RPO threshold.
If the RPO is greater than this value, a warning console message is generated, an
SNMP trap is sent, and the session status changes to Warning. If the value in this field
is other than 0, it must be greater than the value in the Consistency group interval time
(seconds) field and less than the value in the Severe level threshold (seconds) field.
– Severe level threshold (seconds)
Enter the number of seconds that you want to set for the severe level RPO threshold. If
the RPO is greater than this value, an error console message is generated, an SNMP
trap is sent, and the session status changes to Severe. If the value in this field is other
than 0, it must be greater than the value in the Warning level threshold (seconds) field.

For the Role Pair H2-J1, the following Global Mirror options are available:
򐂰 Consistency group interval time (seconds)
Enter how often (in seconds) the Global Mirror session attempts to form a consistency
group. A lower value can reduce the data exposure of the session. However, a lower value
also causes the session to attempt to create consistency groups more frequently, which
can increase network traffic. Possible values are 0 - 65535. The default is 0 seconds.

Global Mirror settings: For the Global Mirror Either Direction with Two Site Practice
session type, you can use the following commands:
򐂰 chsess -maxdrain_h2j1 xx NameSession to set to xx seconds the Maximum
Consistency Group Drain Time for the session NameSession for the Role Pair
H2-J1.
򐂰 chsess -coordint_h2j1 yy NameSession to set to yy milliseconds the Maximum
Coordination Interval Time for the Role Pair H2-J1.

These settings require a Global Mirror session suspension.

򐂰 Recovery Point Objective Alerts

Specify the length of time that you want to set for the RPO thresholds. The values
determine whether a Warning or Severe alert is generated when the RPO threshold is
exceeded for a role pair. The RPO represents the length of time (in seconds) of data
exposure that is acceptable if a disaster occurs. Use the following options to set the RPO
threshold values. For these options, you can specify an RPO threshold in the range of 0 -
65535 seconds. The default is 0 seconds, which specifies that no alerts are generated:
– Warning level threshold (seconds)
Enter the number of seconds that you want to set for the warning level RPO threshold.
If the RPO is greater than this value, a warning console message is generated, an
SNMP trap is sent, and the session status changes to Warning. If the value in this field
is other than 0, it must be greater than the value in the Consistency group interval time
(seconds) field and less than the value in the Severe level threshold (seconds) field.

236 Tivoli Storage Productivity Center for Replication for Open Systems
 – Severe level threshold (seconds)
Enter the number of seconds that you want to set for the severe level RPO threshold. If
the RPO is greater than this value, an error console message is generated, an SNMP
trap is sent, and the session status changes to Severe. If the value in this field is other
than 0, it must be greater than the value in the Warning level threshold (seconds) field.

The following general options also are available:

򐂰 Fail MM/GC if target is online (CKD only)
Select this option to fail any session commands for a Metro Mirror or Global Copy
relationship if the target volume is in the Online state. For more information about this
state, see the documentation for the storage system. This option applies to CKD volumes
only.
򐂰 Reset Secondary Reserves
Select this option to remove any persistent reserves that might be set on the target
volumes of the copy sets when a Start command is issued for the session.

Metro Global Mirror sessions tunable parameters

Different session options are available for Metro Global Mirror session type, depending on the
topology of the session.

Metro Global Mirror

For the Role Pair H1-J3, the following Global Mirror options are available:
򐂰 Consistency group interval time (seconds)
Enter how often (in seconds) the Global Mirror session attempts to form a consistency
group. A lower value can reduce the data exposure of the session. However, a lower value
also causes the session to attempt to create consistency groups more frequently, which
can increase network traffic. Possible values are 0 - 65535. The default is 0 seconds.

Global Mirror settings: For the Metro Global Mirror and Metro Global Mirror with
Practice session type, you can use the following commands:
򐂰 chsess -maxdrain_h1j3 xx NameSession to set to xx seconds the Maximum
Consistency Group Drain Time for the session NameSession for the Role Pair
H1-J3.
򐂰 chsess -coordint_h1j3 yy NameSession to set to yy milliseconds the Maximum
Coordination Interval Time for the Role Pair H1-J3.

These settings require a Global Mirror session suspension.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 237
 򐂰 Recovery Point Objective Alerts
Specify the length of time that you want to set for the RPO thresholds. The values
determine whether a Warning or Severe alert is generated when the RPO threshold is
exceeded for a role pair. The RPO represents the length of time (in seconds) of data
exposure that is acceptable if a disaster occurs. Use the following options to set the RPO
threshold values. For both options, you can specify an RPO threshold in the range of 0 -
65535 seconds. The default is 0 seconds, which specifies that no alerts are generated:
– Warning level threshold (seconds)
Enter the number of seconds that you want to set for the warning level RPO threshold.
If the RPO is greater than this value, a warning console message is generated, an
SNMP trap is sent, and the session status changes to Warning. If the value in this field
is other than 0, it must be greater than the value in the Consistency group interval time
(seconds) field and less than the value in the Severe level threshold (seconds) field.
– Severe level threshold (seconds)
Enter the number of seconds that you want to set for the severe level RPO threshold. If
the RPO is greater than this value, an error console message is generated, an SNMP
trap is sent, and the session status changes to Severe. If the value in this field is other
than 0, it must be greater than the value in the Warning level threshold (seconds) field.

For the Role Pair H2-J3 the following Global Mirror options are available:
򐂰 Consistency group interval time (seconds)
Enter how often, in seconds, the Global Mirror session attempts to form a consistency
group. A lower value can reduce the data exposure of the session. However, a lower value
also causes the session to attempt to create consistency groups more frequently, which
can increase network traffic. Possible values are 0 - 65535. The default is 0 seconds.

Global Mirror settings: For the Metro Global Mirror and Metro Global Mirror with
Practice session type, you can use the following commands:
򐂰 chsess -maxdrain_h2j3 xx NameSession to set to xx seconds the Maximum
Consistency Group Drain Time for the session NameSession for the Role Pair
H2-J3.
򐂰 chsess -coordint_h2j3 yy NameSession to set to yy milliseconds the Maximum
Coordination Interval Time for the Role Pair H2-J3.

These settings require a Global Mirror session suspension.

򐂰 Recovery Point Objective Alerts

Specify the length of time that you want to set for the RPO thresholds. The values
determine whether a Warning or Severe alert is generated when the RPO threshold is
exceeded for a role pair. The RPO represents the length of time (in seconds) of data
exposure that is acceptable if a disaster occurs. Use the following options to set the RPO
threshold values. For those options, you can specify an RPO threshold in the range of 0 -
65535 seconds. The default is 0 seconds, which specifies that no alerts are generated:
– Warning level threshold (seconds)
Enter the number of seconds that you want to set for the warning level RPO threshold.
If the RPO is greater than this value, a warning console message is generated, an
SNMP trap is sent, and the session status changes to Warning. If the value in this field
is other than 0, it must be greater than the value in the Consistency group interval time
(seconds) field and less than the value in the Severe level threshold (seconds) field.

238 Tivoli Storage Productivity Center for Replication for Open Systems
 – Severe level threshold (seconds)
Enter the number of seconds that you want to set for the severe level RPO threshold. If
the RPO is greater than this value, an error console message is generated, an SNMP
trap is sent and the session status changes to Severe. If the value in this field is other
than 0, it must be greater than the value in the Warning level threshold (seconds) field.

The following general options also are available:

򐂰 Fail MM/GC if target is online (CKD only)
Select this option to fail any session commands for a Metro Mirror or Global Copy
relationship if the target volume is in the Online state. For more information about this
state, see the documentation for the storage system. This option applies to CKD volumes
only.
򐂰 Reset Secondary Reserves
Select this option to remove any persistent reserves that might be set on the target
volumes of the copy sets when a Start command is issued for the session.
򐂰 Metro Mirror Suspend Policy options
Select one of the following options to specify the policy for holding or releasing I/O after a
Metro Mirror relationship is suspended. When a relationship is in a Suspended state, write
operations from the source volume are no longer mirrored to the target volume:
– Hold I/O after Suspend
Select this option to prevent the source volume from receiving new data after the
relationship is suspended. Use this option if you want to determine the scope of the
suspension before new data is written to the source volume. This option helps to
ensure that the data on the source and target volumes remains the same. To enable
write operations to the source volume to continue, run the Tivoli Storage Productivity
Center for Replication Release I/O command for the session. If you do not run this
command, write operations are enabled when the hardware timeout value on the
storage system expires.
– Release I/O after Suspend
Select this option to enable the source volume to automatically receive data after the
relationship is suspended. Use this option if you want to limit the affect on the
applications that are writing to the source volume. This option is enabled by default.

Metro Global Mirror with Practice

In addition to the options that were described for the Metro Global Mirror session type (see
“Metro Global Mirror” on page 237), the No Copy FlashCopy option for Role Pair H3-I3 is
available for the Metro Global Mirror with Practice session type. Select this option if you do not
want the hardware to write the background copy until the source track is written to. Data is not
copied to the H2 volume until the blocks or tracks of the i2 volume are modified.

HyperSwap related tunable parameters

When a z/OS host connection is made available to Tivoli Storage Productivity Center for
Replication (see “Adding and connecting host systems” on page 155), other z/OS HyperSwap
options are available for some session types.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 239
 Metro Mirror Single Direction and Metro Mirror FO/FB with Practice
The Enable Hardened Freeze HyperSwap related option applies to Metro Mirror Single
Direction and Metro Mirror FO/FB with Practice session types. Select this option to enable the
z/OS I/O Supervisor to manage freeze operations. With this option, IOS can freeze volumes
regardless of whether the Tivoli Storage Productivity Center for Replication server is started
or stopped.

Note: This option requires the z/OS address spaces Basic HyperSwap Management and
Basic HyperSwap API (see “Managing z/OS HyperSwap from Tivoli Storage Productivity
Center for Replication for Open Systems” on page 355) even though the HyperSwap
function is not available for the type of session.

Metro Mirror FO/FB, Metro Global Mirror, and Metro Global Mirror with Practice
The following HyperSwap related options apply to Metro Mirror FO/FB, Metro Global Mirror,
and Metro Global Mirror with Practice session types:
򐂰 Enable Hardened Freeze
Select this option to enable the z/OS I/O Supervisor to manage freeze operations. With
this option, I/O Supervisor can freeze volumes regardless of whether the Tivoli Storage
Productivity Center for Replication server is started or stopped.
򐂰 Manage H1-H2 with HyperSwap
Select this option to trigger a HyperSwap operation, which redirects application I/O to the
target volumes when there is a failure on the host accessible volumes. Tivoli Storage
Productivity Center for Replication uses HyperSwap to manage the H1-H2 sequence of a
Metro Mirror or Metro Global Mirror session. Setting this option automatically sets the
Release I/O after suspend Metro Mirror policy. The following settings are available:
– Disable HyperSwap
Select this option to prevent a HyperSwap operation from occurring.
– On Configuration Error:
• Partition the system(s) out of the sysplex
Select this option to partition a new system out of the sysplex when an error occurs
because the system cannot be added to the HyperSwap configuration.
• Disable HyperSwap
Select this option to prevent a HyperSwap operation from occurring.
– On Planned HyperSwap Error:
• Partition out the failing system(s) and continue swap processing on the remaining
system(s)
Select this option to partition out the failing system and continue the swap
processing on any remaining systems.
• Disable HyperSwap after attempting backout
Select this option to enable I/O Supervisor to back out the HyperSwap operation, if
possible, if an error occurs during HyperSwap processing. HyperSwap is disabled.

240 Tivoli Storage Productivity Center for Replication for Open Systems
 – On Unplanned HyperSwap Error:
• Partition out the failing system(s) and continue swap processing on the remaining
system(s)
Select this option to partition out the failing systems and continue HyperSwap
processing on the remaining systems when a new system is added to the sysplex
and the HyperSwap operation does not complete.

Requirement: You must restart the system if you select this option.

• Disable HyperSwap after attempting backout

Select this option to enable I/O Supervisor to back out the HyperSwap operation, if
possible, if an error occurs during HyperSwap processing. HyperSwap is disabled.

Note: When Manage H1-H2 with HyperSwap is used with Enable Hardened Freeze,
the freeze option is ignored. HyperSwap includes I/O Supervisor for managing freeze
operations. The Enable Hardened Freeze option ensures data integrity if Tivoli Storage
Productivity Center for Replication freezes and HyperSwap is not enabled for a session.

Open HyperSwap related tunable parameters

When an AIX host connection is established to Tivoli Storage Productivity Center for
Replication (see “Adding and connecting host systems” on page 155), the Manage H1-H2
with Open HyperSwap Open HyperSwap option is available for Metro Mirror Failover/Failback
session type.

Select this option to trigger an Open HyperSwap operation for volumes that are attached to
an IBM AIX host. This option redirects application I/O to the target volumes when there is a
failure on the host accessible volumes. Tivoli Storage Productivity Center for Replication uses
Open HyperSwap to manage the H1-H2 sequence of a Metro Mirror session. Only volumes
that are attached to host systems that are defined in the Tivoli Storage Productivity Center for
Replication Host Systems panel are eligible for Open HyperSwap. The Disable Open
HyperSwap setting also is available. Select this option to prevent an Open HyperSwap
operation from occurring while keeping the configuration on the host system and all source
and target volumes coupled.

For more information about Open HyperSwap implementation, see “HyperSwap configuration
for z/OS and Open systems” on page 45.

4.3.4 Scenarios requiring a full copy

Tivoli Storage Productivity Center for Replication uses all of the DS8000 Copy Services
options to minimize the need to perform a full copy of data for a session while questioning
among its states. Nevertheless, in some cases, a full copy of data is unavoidable. For
instance, starting an Inactive session always requires a full copy of the data (often called
Initial Copy). Furthermore, there are other session-specific conditions where the full copy is
still required. In general, a specific action might not require a full copy, depending on the
sequence of operations that were previously started. There are some particular actions that,
irrespective of the previous actions that were performed, always require a full copy. In these
cases, Tivoli Storage Productivity Center for Replication explicitly warns the user that a full
copy is going to be started, as shown in Figure 4-94 on page 242.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 241
 Figure 4-94 Confirmation panel

In the following sections, we describe the scenarios that require a full copy of data.

Important: Tivoli Storage Productivity Center for Replication Start actions that usually
perform the data copy incrementally might require a full copy to ensure the data
consistency in case of unplanned mirroring disruption situations.

242 Tivoli Storage Productivity Center for Replication for Open Systems
Metro Mirror Failover/Failback with Practice session
While returning to the original configuration after a switch site role, a full copy of data is
required to perform the final StartH1 → H2 action, as shown in Figure 4-95.

Figure 4-95 Start H1 → H2 action that requires a Full Copy

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 243
 Global Mirror Failover/Failback with Practice session
While returning to the original configuration after a switch site role, a full copy of data is
required to perform the final StartH1 → H2 action, as shown in Figure 4-96.

Figure 4-96 Start H1 → H2 action that requires a Full Copy

244 Tivoli Storage Productivity Center for Replication for Open Systems
Global Mirror Either Direction with Two Site Practice session
For this session, the following scenarios require a full copy of data, as shown in Figure 4-97:
򐂰 While performing a switch site role, a full copy of data is required by running the
StartH2 → H1 action.
򐂰 While returning to the original configuration after the switch site role, a full copy of data is
required to perform the final StartH1 → H2 action.

Figure 4-97 Actions that require Full Copy

Metro Global Mirror session

For this session, the following scenarios require a full copy of data:
򐂰 Consider a configuration where the host was running on local site and a switch site role
between local and intermediate site is performed after the Global Mirror was suspended.
While returning to the original configuration, a full copy of data is required to perform the
final StartH1 → H2 → H3 action, as shown in Figure 4-98 on page 246.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 245
 Figure 4-98 Start H1 → H2 → H3 action that requires a Full Copy

򐂰 Consider a configuration where the host was running on the intermediate site and a switch
site role between intermediate and local site is performed after the Global Mirror was
suspended. While returning to H2 → H1 → H3 configuration, a full copy of data is required
to perform the final StartH2 → H1 → H3 action, as shown in Figure 4-99 on page 247.

246 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-99 Start H1 → H2 → H3 action that requires a Full Copy

򐂰 Consider a configuration where the host is running on a local or intermediate site with the
Global Mirror running. When the H3 volumes are recovered with the Metro Mirror
suspended, starting the StartH3 → H1 → H2 action (see Figure 4-100 on page 248)
requires a full copy from the remote to local site, and from the local to intermediate site.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 247
 Figure 4-100 Start H3 → H1 → H2 action requiring a Full Copy

򐂰 Consider a configuration where the host is running on remote site with a cascading Global
Copy running (H3 → H1 → H2). When the H1 volumes are recovered, starting the
StartH3 → H1 → H2 action (see Figure 4-101) or the StartH1 → H2 → H3 action (see
Figure 4-102 on page 249) requires a full copy of data across the three sites.

Figure 4-101 Start H3 → H1 → H2 action that requires a Full Copy

248 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-102 Start H1 → H2 → H3 action that requires a Full Copy

Incremental Resync: In a three-site configuration, the Incremental Resync a Global Mirror

relationship can be established between the local and remote site without the need to
replicate all the data. After the Metro-Global Mirror relationships are established with the
Incremental Resync feature enabled, the Global Mirror must be running for at least 10 - 15
minutes before an incremental resynchronization can be started from local to remote site;
otherwise, a full copy occurs.

Metro Global Mirror with Practice session

For this session, the following scenarios require a full copy of data:
򐂰 Consider a configuration where the host is running on a local or intermediate site with the
Global Mirror running. When the H3 volumes are recovered with the Metro Mirror
suspended, starting the StartH3 → H1 → H2 action (see Figure 4-103) requires a full copy
from the remote to local site, and from the local to intermediate site.

Figure 4-103 Start H3 → H1 → H2 action that requires a Full Copy

򐂰 Consider a configuration where the host is running on remote site with a cascading Global
Copy running (H3 → H1 → H2). When the H1 volumes are recovered, starting the
StartH3 → H1 → H2 action (see Figure 4-104 on page 250) or the StartH1 → H2 → H3
action (see Figure 4-105 on page 250) requires a full copy of data across the three sites.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 249
 Figure 4-104 Start H3 → H1 → H2 action that requires a Full Copy

Figure 4-105 Start H1 → H2 → H3 action that requires a Full Copy

Incremental Resync: In a three sites configuration, the Incremental Resync can establish
Global Mirror relationship between the local and remote site without the need to replicate
all of the data. After the Metro-Global Mirror relationships are established with the
Incremental Resync feature enabled, the Global Mirror must be running for at least 10 - 15
minutes before an incremental resynchronization can be started from the local to remote
site; otherwise, a full copy occurs.

4.4 Use cases

In this section, some helpful use cases are provided for the following scenarios:
򐂰 Practicing disaster recovery by using FlashCopy sessions
򐂰 Two site planned outages scenarios
򐂰 Three site planned outages scenarios

250 Tivoli Storage Productivity Center for Replication for Open Systems
4.4.1 Practicing disaster recovery by using FlashCopy sessions
Tivoli Storage Productivity Center for Replication offers sessions with practice volumes with
which you can practice disaster recovery while maintaining the disaster recovery capabilities.
Practice volumes are available in Metro Mirror Failover/Failback sessions, Global Mirror
Failover/Failback, Global Mirror Either Direction sessions, and Metro Global Mirror with
Practice sessions.

The use of Tivoli Storage Productivity Center for Replication sessions with practice volumes
greatly simplifies the task of creating practice copies for disaster recovery testing. All of the
operations that are needed to create a point-in-time consistent copy of the production data
are performed transparently by running the Flash command.

With sessions with practice volumes, Tivoli Storage Productivity Center for Replication always
assumes that the practice volumes are used for practicing disaster recovery and in the case
of real disaster. All of the recovery actions that Tivoli Storage Productivity Center for
Replication performs in the case of real disaster takes into account this assumption. For
instance, when a Recover command is issued in a session with practice volumes, the Tivoli
Storage Productivity Center for Replication always creates a consistent copy of practice
volumes by flashing the intermediate volumes.

While most disaster recovery implementations benefit from this Tivoli Storage Productivity
Center for Replication feature, this represents a limitation in some cases. For instance, some
disaster recovery implementations use different sets of volumes for testing and real recovery.
In these cases, the sessions with practice volumes should not be used because some
scenarios (for example, the go-home procedure) might lead to unpredictable results. A
combination of replication and FlashCopy sessions can be used instead.

By combining replication and FlashCopy sessions, we can cover a range of situations that
sessions with practice volumes do not handle. In addition to the scenario that we described,
we can manage the following components:
򐂰 Configurations with multiple sets of practice volumes
򐂰 Configuration that uses Space Efficient Volumes as practice volumes
򐂰 Three-site configurations where practice volumes are required at the intermediate site
򐂰 Configuration in which Flash before resync function is required

While implementing these combinations of sessions provides the opportunity to handle more
complex configuration, it increases the management complexity.

The following steps often are required to create a consistent point-in-time copy by using a
combination of two sessions:
1. Suspend the mirroring session and, as a precaution, recover the volumes to be flashed.
2. Run the FlashCopy by using the FlashCopy session.
3. Resume the mirroring of the suspended session.

In the next section, an example of a combination of the Tivoli Storage Productivity Center for
Replication sessions is described.

Using FlashCopy session with Metro Mirror session

In this example, we consider a Metro Mirror configuration with another set of Space Efficient
Volumes in the secondary site. To manage this configuration, we must set up the following
Tivoli Storage Productivity Center for Replication sessions:
򐂰 Session ITSO-TEST: Metro Mirror Failover/Failback session that manages the Metro
Mirror.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 251
 򐂰 Session ITSO-TEST-FC: FlashCopy session that includes managing the FlashCopy and
the use of the secondary Metro Mirror volumes as FlashCopy source. Because the target
volume is a Track Space Efficient volume, the no copy option must be used for this
session.
This configuration is shown in Figure 4-106.

Figure 4-106 Combining Metro Mirror and FlashCopy sessions

As the first step, we must create a consistent copy of the volumes in the Site 2. To achieve
this, perform the Suspend action for the session ITSO-TEST.

Important: With the introduction of the FlashCopy consistency group feature for
FlashCopy sessions (see 4.2.1, “FlashCopy consistency groups for FlashCopy sessions”
on page 182), the FlashCopy session can create a consistent copy of Metro Mirror
secondary volumes, even without suspending the Metro Mirror. The flashing operation
freezes the secondary volume, which freezes the application. The customer must weigh
the cost of doing that at the remote site versus the primary site.

As shown in Figure 4-107, the session ITSO-TEST is in a recoverable state, which means
that the secondary volumes are consistent.

Figure 4-107 Session panel showing the recoverable state for the Metro Mirror session

252 Tivoli Storage Productivity Center for Replication for Open Systems
In this case, a recover operation is not needed because the secondary volumes are already in
a consistent state.

GM and MGM session: Before the introduction of the Pause with Consistency feature,
another Recover operation was always needed to create a consistent copy before flashing
the Global Mirror secondary volumes for Global Mirror and Metro Global Mirror session
types. With this new feature, the Recover operation becomes unnecessary because
following a Suspend operation, the Global Mirror secondary volumes are already in
recoverable state, as shown in Figure 4-26 on page 184.

This applies only to DS8000 Storage Systems that support the Pause with Consistency
feature. For more information, see 4.2.2, “Global Mirror pause with consistency” on
page 183.

The second step is to flash the secondary volumes by issuing a Flash command to the
session ITSO-TEST-FC. Again, the session ITSO-TEST-FC is in a recoverable state, as
shown in Figure 4-108.

Figure 4-108 Session panel showing the recoverable state for the FlashCopy session

Now we can proceed with the final step of resynchronization of the Metro Mirror. Issue the
Start H1 → H2 command for the session ITSO-TEST. Both sessions are now in Normal state,
as shown in Figure 4-109 on page 254.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 253
 Figure 4-109 Session panel showing the Normal Status for the sessions

After the tasks on FlashCopy target volumes are completed, a cleanup is needed to release
the space that is allocated by the Space Efficient volumes. This clean up is automatically
performed when the FlashCopy session is ended.

4.4.2 Two-site planned outages scenarios

In the following sections, we describe some scenarios of planned outages in a two-site Global
Mirror configuration. We also show how to manage these situations with Tivoli Storage
Productivity Center for Replication.

Consider the two-site configuration that is shown in Figure 4-110 on page 255.

254 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-110 Two-site Global Mirror configuration

This configuration can be implemented in Tivoli Storage Productivity Center for Replication by
using a Global Mirror with Practice session, as show in Figure 4-111 on page 256.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 255
 Figure 4-111 Two-site Global Mirror implementation

In the normal operation scenario, the session is running with Global Mirror forming
consistency groups.

For the following scenarios, we assume that the active Tivoli Storage Productivity Center for
Replication server is not affected by any outages.

Planned outage of Site 1 storage systems

In this scenario, we consider a planned maintenance activity that requires powering off the
SIte 1 storage systems. We also describe the go-home procedure to return to the original
configuration. The flow of the Tivoli Storage Productivity Center for Replication operations is
shown in Figure 4-112 on page 257.

Assuming that the host operations are stopped on Site 1, we can complete the following
steps:
1. Start a Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs a Global Mirror pause operation and a suspension of the Global Copy pairs
H1-I2. After the action is complete, the status of the session is Severe and the state is
Suspended.
2. Issue the Recover action on the Tivoli Storage Productivity Center for Replication session.
This performs the following actions:
– Failover i2 volumes to H1 volumes
– Recover the last consistency group (for more information, see 4.2.2, “Global Mirror
pause with consistency” on page 183)

256 Tivoli Storage Productivity Center for Replication for Open Systems
 – FlashCopy the i2 volumes to the H2 volumes
– Force Failover H2 volumes to H1 volumes
The H2 volumes are now ready to be used by host. After the action is complete, the status
of the session is Normal and the state is Target Available.

Now we can start the host operations on the H2 volumes and powering off the storage
systems in Site 1 can proceed. Tivoli Storage Productivity Center for Replication shows an
alert about the communication loss to Site 1 storage systems, but this does not affect the
current configuration.

After the maintenance is completed and the Site 1 storage systems are running again, we can
start the go-home procedure by completing the following steps:
1. Issue the Enable Copy to Site 1 action on the Tivoli Storage Productivity Center for
Replication session. This makes available the actions to be used for the go-home
procedure. This action does not change any state of the session.
2. Start a StartH2 → H1 action on the Tivoli Storage Productivity Center for Replication
session. This starts a Global Copy that performs the following actions:
– Failback i2 volumes to H1 volumes
– Change the mode for I2-H1 pairs from Global Copy to Metro Mirror
– Wait until the I2-H1 pairs are in Full Duplex
– Freeze I2-H1 pairs
– Remove I2-H1 relationships
– Failback H2 volumes to H1 volumes
The session remains in Warning status because the replication configuration that is now
running does not ensure data consistency.

Figure 4-112 Site 1 planned outage state transition diagram

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 257
 After the operations on H2 volumes are stopped, we can proceed with the following steps:
1. Issue the Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs the following actions:
– Change the mode for H2-H1 pairs from Global Copy to Metro Mirror
– Wait until the H2-H1 pairs are in Full Duplex
– Freeze H2-H1 pairs
After the action is complete, the status of the session is Severe and the state is
Suspended.
2. Issue the Recover action on the Tivoli Storage Productivity Center for Replication session.
This makes the H1 volumes available to the host that is performing an H1 to H2 failover.
After the action is complete, the status of the session is Normal and the state is Target
Available.
3. Issue the Enable Copy to Site 2 action on the Tivoli Storage Productivity Center for
Replication session. This makes available the actions to complete the go-home procedure.
This action does not change any state of the session.

Now we can start the host operations on the H1 volumes and complete the go-home
procedure. We start a StartH1 → H2 action on the Tivoli Storage Productivity Center for
Replication session. This performs the following operations:
򐂰 Remove H1-H2 pairs
򐂰 Start H1-I2 pairs in Global Copy mode
򐂰 Wait until the H1-I2 first pass copy is completed
򐂰 Start the Global Mirror H1-H2

The go-home procedure is then completed and the normal operation configuration is
restored. In this case, a full copy of the data is required (for more information, see 4.3.4,
“Scenarios requiring a full copy” on page 241).

Planned outage of Site 2 storage systems

In this scenario, we consider a planned maintenance activity that requires powering off the
SIte 2 storage systems. We also describe the go-back procedure to return to the original
configuration. The flow of the Tivoli Storage Productivity Center for Replication operations is
shown in Figure 4-113 on page 259.

Assuming that the host operations are running on Site 1, we can complete the following steps:
1. Start a Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs a Global Mirror pause operation and a suspension of the Global Copy pairs
H1-I2. After the action is complete, the status of the session is Severe and the state is
Suspended.
Now we can proceed with powering off the storage systems in Site 2. Tivoli Storage
Productivity Center for Replication alerts us about the communication loss to Site 2
storage systems, but this does not affect the current configuration. After the maintenance
is completed and the Site 2 storage systems are running again, we can start the
procedure to return to the original configuration.
2. Start a StartH1 → H2 action on the Tivoli Storage Productivity Center for Replication
session. This performs the following operations:
– Resume the Global Mirror H1-I2
– Wait until the H1-I2 first pass copy is completed
– Start the Global Mirror H1-H2

258 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 4-113 Site 2 planned outage state transition diagram

The go-back procedure is then completed and the normal operation configuration is restored.
This procedure does not require full copy of the data.

4.4.3 Three-site planned outages scenarios

In the following sections, we describe some scenarios of planned outages in a three-site
Metro Global Mirror configuration. We also show how to manage these situations with Tivoli
Storage Productivity Center for Replication.

Consider the three-site configuration that is shown in Figure 4-114 on page 260.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 259
 Figure 4-114 Three-site Metro Global Mirror configuration

This configuration can be implemented in Tivoli Storage Productivity Center for Replication by
using a Metro Global Mirror with Practice session, as shown in Figure 4-115 on page 261.

260 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-115 Three-site Metro Global Mirror implementation

In the normal operation scenario, the session is running with Metro Mirror synchronized and
Global Mirror forming consistency groups.

For the following scenarios, we assume that the active Tivoli Storage Productivity Center for
Replication server is not affected by any outages.

Planned outage of Site 1 storage systems

In this scenario, we consider a planned maintenance activity that requires powering off the
Site 1 storage systems. During the maintenance activity, all of the Disaster Recovery
capabilities must remain active. We also describe the go-home procedure to return to the
original configuration. The flow of the Tivoli Storage Productivity Center for Replication
operations is shown in Figure 4-116 on page 262, Figure 4-117 on page 263, and
Figure 4-118 on page 264.

Assuming that the host operations are stopped on Site 1, we can complete the following
steps:
1. Start a Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs a Freeze operation that makes the H2 volumes in Consistent status. After
the action is complete, the status of the session is Severe and the state is Suspended. The
Global Mirror H2-H3 is still running.
2. Issue the RecoverH2 action on the Tivoli Storage Productivity Center for Replication
session. This performs the following actions:
– Suspend the Global Copy pairs H2-I3
– Failover H2 volumes.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 261
 The H2 volumes are now ready to be used by host. After the action is complete, the status
of the session is Normal and the state is Target Available. After this action is run, the
Global Mirror leg is not creating consistency groups anymore.
3. Issue the Enable Copy to Site 1 action on the Tivoli Storage Productivity Center for
Replication session. This makes available the actions to be used for the go-home
procedure. This action does not change any state of the session.
4. Start a StartH2 → H3 action on the Tivoli Storage Productivity Center for Replication
session. This restarts the Global Mirror and performs the following operations:
– Force Failover I3 volumes to H1 volumes
– Resume the Global Copy H2-I3

Figure 4-116 Site 1 planned outage state transition diagram: Stage One

Now we can start the host operations on the H2 volumes and powering off the storage
systems in Site 1 can proceed. Tivoli Storage Productivity Center for Replication alerts you
about the communication loss to Site 1 storage systems, but this does not affect the current
configuration. For more information about the states, see Table 4-1 on page 160.

262 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-117 Site 1 planned outage state transition diagram: Stage Two

After the maintenance is completed and the Site 1 storage systems are running again, we
can start the following go-home procedure:
5. Start a StartH2 → H1 → H3 action on the Tivoli Storage Productivity Center for
Replication session. This performs the following operations:
– Failback I3 volumes to H1 volumes
– Wait until the I3-H1 first pass copy is completed
– Enable the Incremental Resync from H2 and I3 with noinit option
– Suspend the Global Copy pairs H2-I3
– Wait until the I3-H1 copy is completed (100% copied)
– Failover H1 volumes
– Failback H1 volumes to I3 volumes
– Start H2-H1 Metro Mirror pairs with the Incremental Resync with option override
– Wait until the H1-I3 first pass copy is completed
– Start the Global Mirror H1-H3
After the action is complete, the status of the session is Normal and the state is Prepared.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 263
 After the operations on H2 volumes are stopped, we can proceed with the following steps:
6. Start a Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs a Freeze operation that makes the H1 volumes in Consistent status. After
the action is complete, the status of the session is Severe and the state is Suspended. The
Global Mirror H1-H3 is still running.
7. Issue the RecoverH1 action on the Tivoli Storage Productivity Center for Replication
session. This performs the following actions:
– Suspend the Global Copy pairs H1-I3
– Failover H1 volumes
The H1 volumes are now ready to be used by host. After the action is complete, the status
of the session is Normal and the state is Target Available. After this action is run, the
Global Mirror H1-H3 is not creating consistency groups.
8. Issue the Enable Copy to Site 2 action on the Tivoli Storage Productivity Center for
Replication session. This makes available the actions to complete the go-home procedure.
This action does not change any state of the session.

Figure 4-118 Site 1 planned outage state transition diagram: Stage Three

9. Initiate a StartH1 → H2 → H3 action on the Tivoli Storage Productivity Center for

Replication session. This performs the following operations:
– Force Failover I3 volumes to H2 volumes
– Resume the Global Copy H1-I3
– Failback I3 volumes to H2 volumes
– Wait until the I3-H2 first pass copy is completed
– Enable the Incremental Resync from H1 and I3 with noinit option
– Suspend the Global Copy pairs H1-I3
– Wait until the I3-H2 copy is completed (100% copied)
– Failover H2 volumes
– Failback H2 volumes to I3 volumes
– Start H1-H2 pairs with the Incremental Resync with option override
– Wait until the H2-I3 first pass copy is completed
– Start the Global Mirror H2-H3

The go-home procedure is then completed and the normal operation configuration is
restored. None of these procedures required a full copy of the data.

264 Tivoli Storage Productivity Center for Replication for Open Systems
Planned outage of Site 2 storage systems
In this scenario, we consider a planned maintenance activity that requires powering off the
SIte 2 storage systems. During the maintenance activity, all of the Disaster Recovery
capabilities must be active. We also describe the go-back procedure to return to the original
configuration. The flow of the Tivoli Storage Productivity Center for Replication operations is
shown in Figure 4-119.

Assuming that the host operations are running on Site 1, we can complete the following steps:
1. Start a StartH1 → H3 action on the Tivoli Storage Productivity Center for Replication
session. This starts the Global Mirror from Site 1 to Site 3 and performs the following
operations:
– Freeze H1-H2 pairs
– Failover I3 volumes
– Stop the H2-H3 Global Mirror session
– Remove the H1-H2 pairs
– Start H1-I3 pairs with the Incremental Resync with option recover
– Wait until the H1-I3 first pass copy is completed
– Start the Global Mirror H1-H3

Figure 4-119 Site 2 planned outage state transition diagram

Now we can proceed with powering off the storage systems in Site 2. Tivoli Storage
Productivity Center for Replication alerts you about the communication loss to Site 2
storage systems, but this does not affect the current configuration. After the maintenance
is completed and the Site 2 storage systems are running again, we can start the
procedure return to the original configuration.
2. Start a StartH1 → H2 → H3 action on the Tivoli Storage Productivity Center for
Replication session. This performs the following operations:
– Failback I3 volumes to H2 volumes
– Wait until the I3-H2 first pass copy is completed
– Enable the Incremental Resync from H1 and I3 with noinit option
– Suspend the Global Copy pairs H1-I3
– Wait until the I3-H2 copy is completed (100% copied)
– Failover H2 volumes
– Failback H2 volumes to I3 volumes
– Start H1-H2 pairs with the Incremental Resync with option override
– Wait until the H2-I3 first pass copy is completed
– Start the Global Mirror H2-H3

The go-back procedure is then completed and the normal operation configuration is restored.
None of these procedures required a full copy of the data.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 265
 Planned outage of Site 1 and Site 2 storage systems
In this scenario, we consider a planned maintenance activity that requires powering off the
Site 1 and SIte 2 storage systems. In this case, we temporarily restart the host operation from
the Site 3. We also describe the go-home procedure to return to the original configuration.
The flow of the Tivoli Storage Productivity Center for Replication operations is shown in
Figure 4-20 on page 178 and Figure 4-21 on page 179.

Assuming that the host operations were stopped on Site 1, we can complete the following
steps:
1. Start a Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs a Freeze operation that makes the H2 volumes in Consistent status. After
the action is complete, the status of the session is Severe and the state is Suspended. The
Global Mirror H2-H3 is still running.
2. Issue the RecoverH3 action on the Tivoli Storage Productivity Center for Replication
session. This performs the following actions:
– Suspend the Global Copy pairs H2-I3
– Failover I3 volumes
– Recover the last consistency group (if needed, see 4.2.2, “Global Mirror pause with
consistency” on page 183)
– FlashCopy the I3 volumes to the H3 volumes
The H3 volumes are now ready to be used by host. After the action is complete, the status
of the session is Normal and the state is Target Available.
3. Issue the Enable Copy to Site 1 action on the Tivoli Storage Productivity Center for
Replication session. This makes available the actions to be used for the go-home
procedure. This action does not change any state of the session.

266 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-120 Site 1 and Site 2 planned outage state transition diagram: Stage One

Now we can start the host operations on the H3 volumes and powering off the storage
systems in Site 1 and Site 2 can proceed. Tivoli Storage Productivity Center for
Replication alerts you about the communication loss to Site 1 and Site 2 storage systems,
but this does not affect the current configuration.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 267
 Figure 4-121 Site 1 and Site 2 planned outage state transition diagram: Stage Two

After the maintenance is completed and Site 1 and Site 2 storage systems are running
again, we can start the go-home procedure.
4. Start a StartH3 → H1 → H2 action on the Tivoli Storage Productivity Center for
Replication session. This performs the following operations:
– Remove H1-H2 pairs
– Remove H2-I3 pairs
– Start H1-H2 pairs in Global Copy mode
– Start H3-H1 pairs in Global Copy mode
After the action is complete, the status of the session is Warning and the state is
Preparing. This action performs a full copy from the H3 volumes to the H1 volumes, and, in
cascading, to H2 volumes (see 4.3.4, “Scenarios requiring a full copy” on page 241.).
When the initial copy is completed, we can continue the go-home procedure. The session
remains in Warning status because the replication configuration that is now running does
not ensure data consistency.
After the operations on H3 volumes are stopped, we can proceed with the following steps:
5. Issue the Suspend action on the Tivoli Storage Productivity Center for Replication session.
This performs the following actions:
– Change the mode for H3-H1 pairs from Global Copy to Metro Mirror
– Wait until the H3-H1 pairs are in Full Duplex
– Freeze H3-H1 pairs
– Wait until the H1-H2 copy is completed (100% copied)
– Suspend H1-H2 pairs
After the action is complete, the status of the session is Severe and the state is
Suspended.
6. Issue the Recover action on the Tivoli Storage Productivity Center for Replication session.
This makes the H1 volumes available to the host by removing the H3-H1 pairs. After the
action is complete, the status of the session is Normal and the state is Target Available.

268 Tivoli Storage Productivity Center for Replication for Open Systems
7. Issue the Enable Copy to Site 2 action on the Tivoli Storage Productivity Center for
Replication session. This makes the actions available to complete the go-home procedure.
This action does not change any state of the session.
Now we can start the host operations on the H1 volumes and complete the go-home
procedure.

Figure 4-122 Site 1 and Site 2 planned outage state transition diagram: Stage Three

8. Start a StartH1 → H2 → H3 action on the Tivoli Storage Productivity Center for

Replication session. This performs the following operations:
– Resume H1-H2 pairs in Metro Mirror mode
– Start H2-I3 pairs
– Wait until the H2-I3 first pass copy is completed
– Start the Global Mirror H2-H3

The go-home procedure is then completed and the normal operation configuration is
restored. In this case, a full copy of the data is required to populate Site 2 and to restart the
Global Mirror to Site 3 (see 4.3.4, “Scenarios requiring a full copy” on page 241).

Planned outage of Site 3 storage systems

In this scenario, we consider a planned maintenance activity that requires powering off the
Site 3 storage systems. We also describe the go-back procedure to return to the original
configuration. The flow of the Tivoli Storage Productivity Center for Replication operations is
shown in Figure 4-123 on page 270.

Assuming that the host operations are running on Site 1, we can complete the following steps:
1. Start a SuspendH2H3 action on the Tivoli Storage Productivity Center for Replication
session. This performs a Global Mirror pause operation and a suspension of the Global
Copy pairs H2-I3. After the action is complete, the status of the session is Severe and the
state is SuspendedH2H3.
Now we can proceed with powering off the storage systems in Site 3. Tivoli Storage
Productivity Center for Replication alerts you about the communication loss to Site 3
storage systems, but this does not affect the current configuration. After the maintenance
is completed and the Site 3 storage systems are running, we can start the procedure to
return to the original configuration.
2. Start a StartH1 → H2 → H3 action on the Tivoli Storage Productivity Center for
Replication session. This performs the following operations:
– Resume the Global Copy H2-I3
– Wait until the H2-I3 first pass copy is completed

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 269
 – Restart the Global Mirror H2-H3

The go-back procedure is then completed and the normal operation configuration is restored.
This procedure does not require full copy of the data.

Figure 4-123 Site 3 planned outage state transition diagram

4.5 Troubleshooting
This section provides troubleshooting guidance for managing Tivoli Storage Productivity
Center for Replication with DS8000 storage systems.

4.5.1 Managing loss of connection to storage system

The loss of connection to DS8000 storage systems leads all the active Tivoli Storage
Productivity Center for Replication sessions that are using that DS8000 to an indeterminate
state. In Figure 4-124, the console log shows the connection loss events.

Figure 4-124 Console Log showing a connection loss event

In Figure 4-125 on page 271 and Figure 4-126 on page 271, the statuses of the storage
system and session after a connection loss are shown.

270 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 4-125 Storage System Details panel that shows Disconnected status

Figure 4-126 Session Details panel that shows Severe status

Tivoli Storage Productivity Center for Replication continues polling the storage systems. After
the connection problem is fixed, the connectivity to the storage system and the actual session
status are immediately restored.

Other than the full box failure, there are two main causes that lead to a DS8000 connection
loss: network problems and HMC problems. In the following session, we describe this two
connection loss scenario.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 271
 Important: The loss of connection to storage systems from the stand-by Tivoli Storage
Productivity Center for Replication server does not affect the active sessions status.
Nevertheless, it is recommended that you fix the cause of the connection loss immediately
to avoid any serious issues if there is takeover. The same problem determination for the
active server that is described later in this section can be used to analyze the stand-by
server connection loss events.

Network problem
Network problems often are temporary events because the redundancy of the network
infrastructure provides the means to recover multiple hardware or software failures. Typical
causes of persistent Tivoli Storage Productivity Center for Replication connection losses are
major hardware or software problems in the network infrastructure and network security
policies reconfiguration. When the network problem becomes persistent, some Tivoli Storage
Productivity Center for Replication checking can be done to understand the nature of the
problem.

In the following section, we describe some of most common network issues that lead to a
persistent connection loss. Some mitigation tasks also are proposed.

Tivoli Storage Productivity Center for Replication server network isolation

When the network issue affects only the Tivoli Storage Productivity Center for Replication
server or the LAN that Tivoli Storage Productivity Center for Replication is connected to, a
complete loss of the connectivity to all storage systems (not only DS8000) occurs. The
connection to the stand-by server also is affected. In this case, because the remote
connection to the Tivoli Storage Productivity Center for Replication also is not available, only
a physical direct connection to the server can help analyze and resolve the problem. The
Tivoli Storage Productivity Center for Replication HA configuration that uses two different
LANs for active and stand-by server can mitigate this kind of problem.

Storage systems network isolation

When the network issue affects a storage system’s LAN (assuming that is different from the
Tivoli Storage Productivity Center for Replication LAN), a complete loss of the connectivity to
all storage systems (not only DS8000) that are using that LAN occurs. In this case, the
connectivity to Tivoli Storage Productivity Center for Replication is still available and this can
help to address the issues. A dual HMC configuration that uses two different LANs for primary
and secondary HMC can mitigate this kind of problem.

HMC problems
The DS8000 HMC is a multi-purpose piece of equipment that provides the services that the
client needs to configure and manage the storage and manage some of the operational
aspects of the Storage System. It also provides the interface where service personnel
perform diagnostic and repair actions.

The HMC is the communication interface between Tivoli Storage Productivity Center for
Replication and DS8000 controller. A software or hardware failure of the HMC causes the
loss of communication between Tivoli Storage Productivity Center for Replication and
DS8000. In this case, the HMC also becomes unresponsive to other connection types, such
as the DSCLI or a simple ping. The HMC functions are not related to data management, so
an HMC failure does not affect the normal DS8000 operations.

When a software failure occurs, a simple reboot of the HMC is enough to resolve the problem
in most cases. More serious software problems might require a fresh installation of the HMC.
A dual HMC configuration can mitigate this kind of problem.

272 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: HMC problems often simultaneously affect active and stand-by Tivoli Storage
Productivity Center for Replication server.

Internal communication problems

The HMC uses the ESSNI service to communicate to the internal DS8000 cluster nodes. If
this service is not working, the HMC loses the communication to the DS8000 clusters. In this
case, the HMC is still reachable but cannot carry any command to the DS8000, which
includes Tivoli Storage Productivity Center for Replication commands. In Figure 4-127, we
show how the Connection Details panel reports this status. In most cases, a restart of the
ESSNI service (which can be performed only by an IBM service representative) is enough to
resolve the problem.

Figure 4-127 Connection Details panel

4.5.2 Managing suspending events

Unplanned replicating suspension events can occur following a hardware or connectivity
failure. The suspension event notification is sent from DS8000 to the Tivoli Storage
Productivity Center for Replication through the IP storage system connection and can affect
one or more active sessions. Notifications that are related to volumes that are not used in
active sessions are discarded from Tivoli Storage Productivity Center for Replication.

Tivoli Storage Productivity Center for Replication performs different actions depending on the
session that is affected by the suspension event. In particular, if the suspension event is
related to a Metro Mirror replication that is managed by Tivoli Storage Productivity Center for
Replication with a Metro Mirror or Metro Global Mirror session types, Tivoli Storage
Productivity Center for Replication ensures the data consistency that is starting a freeze.

Following a suspension, Tivoli Storage Productivity Center for Replication updates the
affected session with a status and a state accordingly to the event. In particular, the status
always becomes Severe because a major disruption of the replication configuration occurred
while the state depends on the type of replication that was affected (Metro Mirror or Global
Mirror) and on the state at the suspension time.

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 273
 Global Copy relationships that are affected by suspension events can resume automatically
after the cause of the suspension is removed. For this reason, Tivoli Storage Productivity
Center for Replication sessions that involve Global Mirror replication can resume from a
suspension without any user intervention. Temporary suspensions in Global Copy
relationships can occur because of poor performance in the replication operations, for
example.

In the following sections, we describe how to analyze and restore a Tivoli Storage Productivity
Center for Replication session after a persistent suspension event.

Analyzing the suspension events

Tivoli Storage Productivity Center for Replication reports the suspending event in the session
information and in the console log. Figure 4-128 shows the Session Details panel in which the
suspension event is reported.

Figure 4-128 Session Details panel after a suspension event

Clicking the role pair that is affected by the suspension opens the role pair panel, as shown in
Figure 4-129. In this panel, all of the pairs that are affected by the suspension are identified
with an error symbol.

Figure 4-129 Role pair H1-H2 panel that shows the pairs that are affected by the suspension

274 Tivoli Storage Productivity Center for Replication for Open Systems
Clicking the pair shows a description of the error, as shown Figure 4-130.

Figure 4-130 Detailed message of the suspension event

Finally, when the message code is clicked, the full error description and the reason codes are
displayed, as shown in Figure 4-131.

Figure 4-131 Error full description panel

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 275
 In the Tivoli Storage Productivity Center for Replication console log, the error message and
the actions that were started automatically by Tivoli Storage Productivity Center for
Replication are displayed, as shown in Figure 4-132.

Figure 4-132 Console log reporting a suspension event

All of the information that is provided by Tivoli Storage Productivity Center for Replication can
be used as a starting point to determining the cause of the suspension event.

Restoring the session after a suspension event

It is important to highlight that there is no standard action to perform following a suspension
event; any occurrence should be treated as a separate instance. Even if in most cases
restarting the session is enough to restore the normal status of the session, a complete root
cause analysis is always recommended. Starting actions without identifying the cause of the
suspension event can lead to unpredictable results.

Further, identifying the proper action to perform, even after the reason for the suspension
event was explained, might not always be an easy task. In rolling disaster scenarios, for
example, the pair suspension can be only the first in a sequence of events that leads to a
major disruption. In these cases, the appropriate action might not be restoring the session to
the status before the suspension moment, but a full session recovery to an alternative site
might be considered instead.

Suspension events can occur at any time, even during a session transition from a
configuration to another (for example, during a go-home procedure after a planned outage as
described in 4.4.2, “Two-site planned outages scenarios” on page 254). For this reason,
accordingly to the status and the state at the suspension moment, by using Tivoli Storage
Productivity Center for Replication, users can start the action that is needed to restore (or
recover) the session to the wanted configuration.

After the session restart is identified as the appropriate action because of the suspension
event analysis, we can proceed the session restoration process. Table 4-4 on page 277
shows the actions that can be performed to restore a session according to the Session type,
the configuration that is running at the moment of the suspension, and the pair that was
suspended.

276 Tivoli Storage Productivity Center for Replication for Open Systems
Table 4-4 Action to restart a session following a suspension event
Session Type Configuration running Pair suspended Action to restore

Metro Mirror H1 → H2 H1-H2 Start H1 → H2

H2 → H1 H2-H1 Start H2 → H1

Global Mirror H1 → H2 H1-H2 Start H1 → H2

H2 → H1 H2-H1 Start H2 → H1

Metro Globe Mirror H1 → H2 → H3 H1-H2 Start H1 → H2 → H3

H1 → H2 → H3 H2-H3 Start H1 → H2 → H3

H2 → H1 → H3 H2-H1 Start H2 → H1 → H3

H2 → H1 → H3 H1-H3 Start H2 → H1 → H3

H3 → H1 → H2 H3-H1 Start H3 → H1 → H2

H3 → H1 → H2 H1-H2 Start H3 → H1 → H2

H1 → H3 H1-H3 Start H1 → H3

H1 → H2 H2-H3 Start H1 → H2

Chapter 4. Using Tivoli Storage Productivity Center for Replication with DS8000 277
278 Tivoli Storage Productivity Center for Replication for Open Systems
 5

Chapter 5. Tivoli Storage Productivity

Center for Replication with SAN
Volume Controller and Storwize
family
In this chapter, we describe the use of Tivoli Storage Productivity Center for Replication v5.2
to manage and monitor Copy Services in the IBM Storwize family of Storage Systems. We
show you how to set up replication sessions, how to manage these sessions, and give some
tunable parameters guidance. We also provide some disaster recovery scenarios and
troubleshooting guidance.

The IBM Storwize family of Storage Systems includes the following models:
򐂰 IBM System Storage SAN Volume Controller
򐂰 IBM Storwize V7000 and V7000 Unified
򐂰 IBM Flex Systems V7000 Storage Node
򐂰 IBM Storwize V3700
򐂰 IBM Storwize V3500 (available in some geographies)

Note: The IBM Flex System™ V7000 Storage Node is available as an integrated
component of IBM Flex System and IBM PureFlex™ Systems. Although functionally
equivalent to Storwize V7000, Flex System V7000 is not officially supported by Tivoli
Storage Productivity Center for Replication V5.2. Ask for a request for price quotation
(RPQ) if you intend to use the Flex Systems V7000 Storage Node with Tivoli Storage
Productivity Center for Replication V5.2.

For more information about the IBM Storwize family of Storage Systems, see this website:

http://www-03.ibm.com/systems/storage/storwize/

© Copyright IBM Corp. 2014. All rights reserved. 279

 This chapter includes the following topics:
򐂰 Introduction
򐂰 SAN Volume Controller
򐂰 Storwize Products
򐂰 New Functions
򐂰 Session Types and Setup
򐂰 Why and when to use certain session types
򐂰 Disaster Recovery use cases
򐂰 Troubleshooting

280 Tivoli Storage Productivity Center for Replication for Open Systems
5.1 Introduction
This section provides an overview of the Storwize family and describes the replication
Session types that are supported on the Storwize product portfolio.

5.1.1 The Storwize family of Storage Products

The first product that was started in the Storwize family of Storage systems was the SAN
Volume Controller in July 2003. Since then, new members were added to the family so that
business environments of any size can find a model that best fits their needs. Table 5-1 shows
the basic features that differentiate the members of the Storwize family.

Table 5-1 Storwize Storage Systems Basic differentiators

SAN V7000 V7000 V3700 V3500
Volume Unified
Controller

Nodes or Controllers 2, 4, 6, or 8 2, 4, 6, or 8 2, 4, 6, or 8 2 2

I/O Groups 1-4 1-4 1-4 1 1

External Storage Array Yes Yes Yes No No

Virtualization

FlashCopy Yes Yes Yes Yes Yes

Global Mirror Yes Yes Yes Yes No

Metro Mirror Yes Yes Yes Yes No

Block Storage Yes Yes Yes Yes Yes

Virtualization

File system Services No No Yes No No

(NAS - CIFS or NFS)

Note: All members of the Storwize family run the same code, so they provide the same
Copy Services functions to the storage managed by them as external arrays (SAN Volume
Controller), internal disks (V3700, V3500), or both (V7000 and V7000 Unified). They also
support Remote Copy services between different family models.

5.1.2 Tivoli Storage Productivity Center for Replication and the Storwize
family
Tivoli Storage Productivity Center for Replication for Open Systems provides copy services
management for SAN Volume Controller, V7000, V7000 Unified, and V3700 with the following
session types. IBM Storwize V3500 does not support Global or Metro Mirror. Only FlashCopy
sessions are supported for this model:
– FlashCopy
– Metro Mirror Single Direction
– Metro Mirror Failover/Failback
– Metro Mirror Failover/Failback with Practice
– Global Mirror Single Direction
– Global Mirror Failover/Failback

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 281
 – Global Mirror Failover/Failback with Practice
– Global Mirror Failover/Failback with Change Volumes

Consider the following points concerning Tivoli Storage Productivity Center for Replication
with the Storwize family of Storage Systems:
򐂰 Copy Services in the Storwize family have similar names (such as, FlashCopy, Global, and
Metro Mirror) and the same type of functionality as those in the IBM DS8000 family, but
they are different in their internal working, limits, and capabilities. For example, Global
Mirror in DS8000 involves Journal Volumes, which are not applicable for SAN Volume
Controller. You see Tivoli Storage Productivity Center for Replication lists similar session
types in Chapter 4, “Using Tivoli Storage Productivity Center for Replication with DS8000”
on page 159, but do not confuse them. Also, it is impossible to configure remote copy
services between storage systems of different families; for example, attempting to
configure a Global Mirror session between a Storwize V7000 and a DS8870.
򐂰 After you deploy Tivoli Storage Productivity Center for Replication (including storage
systems that are under its management and configured data replication sessions in them),
you should no longer use the storage systems native management interface (GUI or
command-line interface) to manage these replication sessions unless you are facing a
problem with Tivoli Storage Productivity Center for Replication and were instructed to do
so by an IBM Service Representative. Doing so causes a number of inconsistencies in
Tivoli Storage Productivity Center for Replication database and logs and can lead to
unpredictable results.

In the following sections, we provide a brief architectural description of each Storwize Storage
product as an introduction to explore in detail the use of Tivoli Storage Productivity Center for
Replication. For more information about the Storwize family of Storage Systems and their
respective Copy Services functions, see the IBM Redbooks that are listed in Table 5-2.

Table 5-2 Recent IBM Redbooks on Storwize Storage products

IBM Redbooks Number Website

IBM System Storage SAN Volume SG24-7521-02 http://publib-b.boulder.ibm.com

Controller Best Practices and Performance /abstracts/sg247521.html?Open
Guidelines

IBM System Storage SAN Volume SG24-7574-02 http://publib-b.boulder.ibm.com

Controller and Storwize V7000 Replication /abstracts/sg247574.html?Open
Family Services

Implementing the IBM System Storage SG24-7933-01 http://publib-b.boulder.ibm.com

SAN Volume Controller V6.3 /abstracts/sg247933.html?Open

Implementing the IBM Storwize V7000 SG24-7938-01 http://publib-b.boulder.ibm.com

V6.3 /abstracts/sg247938.html?Open

Implementing the IBM Storwize V3700 SG24-8107-00 http://publib-b.boulder.ibm.com

/abstracts/sg248107.html?Open

282 Tivoli Storage Productivity Center for Replication for Open Systems
5.2 SAN Volume Controller
The SAN Volume Controller’s primary function is to act as a gateway, which provides a
common virtualization layer to other storage systems, such as DS8870, XIV, and supported
storage systems from other vendors (see Figure 5-1). Among other features, SAN Volume
Controller provides a common set of Advanced Copy Services functions that can be used
across all its managed storage systems, whether homogeneous or heterogeneous.

Figure 5-1 SAN Volume Controller conceptual and topology overview

SAN Volume Controller was designed under project COMmodity PArts Storage System or
COMPASS with the goal of using, as many as possible, off-the-shelf standard components.
Its hardware is based on IBM xSeries® 1U rack servers. The most recently released
hardware node, the 2145-CG8, is based on IBM System x3550 M3 server technology with an
Intel Xeon 5500 2.53 GHz quad-core processor, 24 GB of cache, four 8 Gbps Fibre Channel
ports, and two 1 GbE ports, as shown in Figure 5-2.

Figure 5-2 One pair of SAN Volume Controller 2145-CG8 nodes

The SAN Volume Controller node model CG8 now offers a FlashCopy ports expansion option
that gives you four more FlashCopy ports per node. By using this expansion option, some of
these other ports can be configured as dedicated to remote copy services connections.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 283
 Tip: When SAN Volume Controller is used intensively for remote copy services, the use of
dedicated ports for remote copy services significantly reduces the odds of encountering
problems because of Fibre Channel fabric traffic congestion. In this type of scenario,
consider the use of this FlashCopy ports expansion option and modify the SAN zoning
configuration.

5.3 Storwize Products

As of April 2012, IBM shipped over 21,500 SAN Volume Controller engines to almost 7,000
SAN Volume Controller systems worldwide. To extend the offerings range of storage
virtualization, new products were developed that were based on SAN Volume Controller that
provides the following advantages:
򐂰 Run the same code and provide the same functions and benefits in a more compact,
dedicated hardware packaging.
򐂰 Include their own, underlying storage layer that supports different kinds of disks for
different purposes.

5.3.1 Storwize V7000

The Storwize V7000 controller module includes two redundant controller canisters and 12 or
24 SAS disk drives in a 2U standard, 19-inch rack cabinet, as shown in Figure 5-3. Optionally,
this controller module can be attached to Expansion modules to increase the number of
managed disks. With an optional license, the Storwize V7000 can provide the same
virtualization layer that it gives to its internal disks to external, supported storage arrays that
are attached to it through SAN.

Figure 5-3 Storwize V7000 module

The following models are available for Controller or Expansion modules, depending on the
capacity of the hard disk drives (HDDs) that best suits your needs:
򐂰 One model that can hold up to 12 Large Form Factor (LFF), 3.5-inch SAS HDDs
򐂰 One model that can hold up to 24 Small Form Factor (SFF), 2.5-inch SAS HDDs, or
E-MLC solid-state drive (SSDs)

This makes the Storwize V7000 internal storage highly scalable. Each Controller enclosure
can have up to nine expansion enclosures that are attached to it. By using SFF enclosures,
one I/O group can have up to 240 HDDs. A Storwize V7000 system can have up to four
Controller enclosures or I/O groups.

284 Tivoli Storage Productivity Center for Replication for Open Systems
 Layers
The introduction of the Storwize V7000 with its own internal storage also introduced the
concept of layers in the remote copy partnerships between systems. Layers include the
following features:
򐂰 There are two layers, the storage layer and the replication layer. The layer that a system
belongs to is controlled by a system parameter, which can be changed by using the
command-line interface (CLI) command chsystem -layer <layer>.
򐂰 SAN Volume Controller systems always are in the replication layer, whereas a Storwize
V7000 can be in the replication or storage layer. By default, a Storwize V7000 is in the
storage layer.
򐂰 Changing the layer is only performed at initial setup time or as part of a major
reconfiguration. To change the layer of a Storwize, the system must meet the following
pre-conditions:
– The Storwize must not have any host objects defined and must not be presenting any
volumes to an SAN Volume Controller as managed disks.
– The Storwize must not be visible to any other SAN Volume Controller or Storwize in the
SAN fabric. This prerequisite might require SAN zoning changes.
򐂰 A system can form remote copy partnerships with systems in the same layer only.
򐂰 A SAN Volume Controller can virtualize a Storwize V7000 only if the Storwize V7000 is in
Storage layer.
򐂰 A Storwize V7000 in Replication layer can virtualize a Storwize V7000 in Storage layer.

Figure 5-4 shows the concept of layers.

Figure 5-4 Storwize partnerships and layers

Note: Tivoli Storage Productivity Center for Replication does not configure the layer that a
Storwize V7000 belongs to, nor does it establish partnerships. This must be done via the
Storwize GUI or CLI before you attempt to create a Session in Tivoli Storage Productivity
Center for Replication.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 285
5.3.2 Storwize V7000 Unified
At the block storage level, the Storwize V7000 Unified is functionally identical to the Storwize
V7000. The difference between the products is that a pair of file system management nodes
were included on top of the standard Storwize V7000. These nodes run in a cluster with the
same code as the IBM Scale Out Network Attached Storage product and use volumes that
are provided by the Storwize V7000 to build file systems and provide CIFS or NFS services to
the attached IP networks.

Figure 5-5 shows the Overview window of the Storwize V7000 Unified with the file system
portion highlighted in the red box.

Figure 5-5 Storwize V7000 Unified Overview window

Tivoli Storage Productivity Center for Replication version 5.2 supports Block level Copy
Services in Storwize V7000 Unified version 1.4, but does not yet support the management of
file system Replication or Remote Caching. For Tivoli Storage Productivity Center for
Replication, Storwize V7000 and Storwize V7000 Unified are equivalent in Copy Services
management.

5.3.3 Storwize V3700 and V3500

The Storwize V3700 is fancifully equivalent to the V7000. It has the same enclosure models,
which can have Large Form Factor 3.5-inch HDDs or Small Form Factor 2.5-inch HDDs. The
Storwize V3700 and V7000 feature the following differences:
򐂰 Storwize V3700 has its configuration that is limited to one controller enclosure and up to
four expansion enclosures.
򐂰 Storwize V3700 does not support virtualization of external storage arrays; it supports its
own internal disks only.

The Storwize V3500, which is available only in a few geographies, accepts no expansion
enclosures and does not support remote replication.

286 Tivoli Storage Productivity Center for Replication for Open Systems
5.4 New Functions
Among the many new functions that are included in Tivoli Storage Productivity Center for
Replication version 5.2, two of them address the management of new major functions in the
Storwize family. The following new major functions are described in the following sections:
򐂰 Global Mirror Failover/Failback with Change Volumes session
򐂰 Support for the SAN Volume Controller 6.4 option to move volumes between I/O groups

5.4.1 Global Mirror Failover/Failback with Change Volumes session

The Global Mirror Failover/Failback with Change Volumes session is available only for the
Storwize family of Storage Systems. It provides the same capabilities as the Global Mirror
Failover/Failback session type, but it also provides the option of enabling or disabling the use
of Change Volumes.

Change Volumes are composed of a source change volume and a target change volume that
contain a point-in-time image of the data from the source and target volumes. A FlashCopy
operation occurs between the source volume and the source change volume. The frequency
of the FlashCopy operation is determined by the cycle period. The data on the source change
volume is then replicated to the target volume, and finally to the target change volume.

Important: Do not confuse Change Volumes with FlashCopy target volumes or Practice
volumes. Change Volumes are dedicated to their respective SAN Volume Controller Global
Mirror sessions. Practice volumes are available for some session types in the DS8000
family.

Because the data that is replicated between sites contains point-in-time changes rather than
all changes, a lower bandwidth link is required between the sites. A regular Global Mirror
configuration requires the bandwidth between sites to meet the long-term peak I/O workload,
whereas Global Mirror with Change Volumes requires it to meet the average I/O workload
across a Cycle Period only. However, the use of change volumes can result in an increase to
your data exposure because it changes your Recovery Point Objective (RPO). Therefore, you
might want to include or exclude change volumes in your Global Mirror sessions, depending
on your network traffic or business requirements.

Note: One important feature of this kind of session is that you can monitor the current RPO
of your session. You can set two levels of thresholds, Warning and Severe, from 1 second
to 48 hours, and Tivoli Storage Productivity Center for Replication sends you an alert if
your remote copy session is no longer protecting your data for any reason with the RPO
you expect.

5.4.2 Support for the SAN Volume Controller 6.4 option to move volumes
between I/O groups
Tivoli Storage Productivity Center for Replication version 5.2 supports in its operations the
new option that is available in SAN Volume Controller code version 6.4 and higher to
non-disruptively migrate a volume to another I/O group. This is often done to manually
balance the workload across the nodes in a Storwize clustered system. A compressed
volume can also be moved, and you can specify the preferred node in the new I/O group.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 287
 Tip: The move volume operation does not change which I/O groups can access the volume,
only the caching I/O group is changed. If you move a volume that is in a FlashCopy
Session, the FlashCopy bitmaps remain in the original I/O group. Hence, these volumes
cannot be moved when the FlashCopy Session is in Prepare state.

5.5 Session Types and Setup

Because all products in the Storwize family run the same code and have the same Copy
Services functionality, the available Session types are the same as the types that are
described in 5.1.2, “Tivoli Storage Productivity Center for Replication and the Storwize family”
on page 281.

In this section, we describe how to set up Copy Services sessions for storage systems from
the Storwize family. The following assumptions are made:
򐂰 Storage Systems were already configured into Tivoli Storage Productivity Center for
Replication, including user IDs with proper privilege to create and manage sessions.
򐂰 Storage Systems that were involved were properly configured to handle Copy Services.
Also, proper licenses were enabled, when applicable.
򐂰 Proper communication links were established and configured. In the case of Metro Mirror,
that means the inter-switch links (ISLs) and zoning between the Storage Systems are in
place.
򐂰 Partnerships between source and target systems were successfully created.
򐂰 Source and target volumes were already provisioned in the storage systems that are
involved. Special attention should be paid if thin-provisioned volumes are used in
sessions, when applicable.

Note: These tasks were not described in more detail to avoid repetition with other
published documents. For more information about how to perform these prerequisite tasks,
see the publications that are listed in Table 5-2 on page 282.

Creating sessions by using the web-based GUI

Creating sessions by using the web-based GUI is a two-step process that is run by two
wizards in sequence. The first wizard creates the basic session and prompts you to choose
the hardware type, session type, and storage systems that participate in the session, with a
few tunable parameters. The second wizard adds Copy Sets to the session, and prompts you
to select the volumes and the roles each volume plays in each Copy Set.

Complete the following steps:

1. Go into Tivoli Storage Productivity Center for Replication by using a user ID with
Administration privilege and, in the left menu, click Sessions → Create Session, as
shown in Figure 5-6 on page 289.
A new browser window opens and starts the Create Session wizard starts.

288 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 5-6 Tivoli Storage Productivity Center for Replication web-based GUI Create Session wizard

2. In the Create Session wizard window that is shown in Figure 5-7, choose the hardware
type and session type. Click Next.

Figure 5-7 Choose Hardware Type and Session Type

Note: The Create Session wizard presents you with three options in the Storwize family:
SAN Volume Controller, Storwize Family (In this case, eStorwize V7000, V3700, or V3500),
and Storwize V7000 Unified. However, regardless of the hardware type you choose, you
have the same options in the Choose Session Type drop-down menu.

5.5.1 FlashCopy sessions

Complete the following steps:
1. In the main Tivoli Storage Productivity Center for Replication window, click Sessions →
Create Session, as shown in Figure 5-6 on page 289.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 289
 2. In the Create Session wizard, Choose Session Type window, select the following
Hardware Type and FlashCopy as Session Type:
– Hardware Types:
• SAN Volume Controller
• Storwize Family
• Storwize V7000 Unified
– Session Types: FlashCopy
3. The Session Properties window opens. Enter a name and a description for your session.
By using the session name, you can uniquely identify the session type and help you
deduce to which servers, applications, or services it relates so that you can quickly debug
any errors. In the example that is shown in Figure 5-8, we entered FCDB2session as our
session name.

Figure 5-8 FlashCopy Session Properties for Storwize family

4. Configure the FlashCopy session tunable parameters. The Incremental flag (see
Figure 5-8) prevents FlashCopy from copying the entire source volume whenever a Flash
command is run, which reduces the copy time and the Storwize cluster workload. The
background copy rate specifies the speed at which that particular FlashCopy session
moves data.
Table 5-3 on page 291 shows the correlation between the values that are specified and
the actual copy speed. A value of zero disables the background copy, and 256 KB is the
default grain size in SAN Volume Controller code 6.2 and up. Click Next.

290 Tivoli Storage Productivity Center for Replication for Open Systems
 Table 5-3 Background Copy Rate
Background copy Data copied per Grains per second Grains per second
rate second (256 KB grain) (64 KB grain)

01-10 128 KB 0.5 2

11-20 256 KB 1 4

21-30 512 KB 2 8

31-40 1 MB 4 16

41-50 2 MB 8 32

51-60 4 MB 16 64

61-70 8 MB 32 128

71-80 16 MB 64 256

81-90 32 MB 128 512

91-100 64 MB 256 1024

5. Configure the Site Locations. In the case of FlashCopy sessions, there is only one site.
Select the storage system that hosts the source and target volumes and performs the
FlashCopy operation. In the example that is shown in Figure 5-9, we selected svc08 as
the storage system. Click Next.

Figure 5-9 FlashCopy Site Locations for Storwize family

In the wizard, you see the results of the Create Session operation and you have the option of
finishing the wizard without further action or starting the Add Copy Sets wizard, as shown in
Figure 5-10 on page 292.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 291
 Figure 5-10 FlashCopy Create Session Results

6. You can start the Add Copy Sets wizard any time by selecting Sessions in the upper left
menu. Select the session to which you want to add copy sets, then select Add Copy Sets,
as shown in Figure 5-11.

Figure 5-11 Add Copy Sets to a Session

7. The Add Copy Sets wizard open a new window and prompts you to select the source
volume, which is referred to by Tivoli Storage Productivity Center for Replication as Host1
(H1). Select the storage system from the drop-down menu, then select the I/O group to
which the volume belongs, then the volume, as shown in Figure 5-12 on page 293. Click
Next.

292 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: You can also add copy sets to a session by importing a previously exported
comma-separated value (CSV) file. For more information about this procedure, see
3.10.2, “Importing CSV files” on page 132.

Figure 5-12 Select the source volume Host1 for the copy set

8. The wizard prompts you to select the target volume Target1 (T1); in this case, Host1
volume Red_vol01. Select H1, as shown in Figure 5-13. Click Next.

Figure 5-13 Select the target volume Target1 for the copy set

9. By using the wizard, you can add more Copy Sets to the list before they are added to the
session. Click Add More in the Select Copy Sets window (as shown in Figure 5-14 on
page 294) and then repeat steps 5 and 6, as needed. Confirm that the required Copy Sets
are selected and then click Next.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 293
 Figure 5-14 Select Copy Sets to add to Session

10.You are prompted to reconfirm the number of Copy Sets that you want to add to the
Session and, if confirmed, perform the actual operation. A message is shown with the
results.

Note: Tivoli Storage Productivity Center for Replication automatically creates a

Consistency Group for the Copy Sets in a FlashCopy Session. Copy Sets that are added
later to this FlashCopy Session by Tivoli Storage Productivity Center for Replication also
are added to this Consistency Group.

If the operation was successful, click Finish to close the wizard.

If the operation was unsuccessful, verify the messages in the Console window to
troubleshoot the operation before you try again.

5.5.2 Metro Mirror sessions

The Metro Mirror session creation process is similar to the FlashCopy session creation
process. You create a Session by selecting the hardware and session types, then add copy
sets to the session. The difference is that the wizard prompts you for the specific parameters
for this kind of session. Complete the following steps:
1. In the main Tivoli Storage Productivity Center for Replication window, click Sessions →
Create Session.

Note: A comparable process was shown in 5.5, “Session Types and Setup” on
page 288, beginning with Figure 5-6 on page 289. The session creation process is
similar across all session types; therefore, not all panels are repeated here.

294 Tivoli Storage Productivity Center for Replication for Open Systems
 2. In the Create Session wizard, Choose Session Type window, select the following
Hardware Type and one of the Synchronous Session Types:
– Hardware Types:
• SAN Volume Controller
• Storwize Family
• Storwize V7000 Unified
– Session Types:
• Metro Mirror Single Direction
• Metro Mirror Failover/Failback
• Metro Mirror Failover/Failback with Practice
3. In the Properties window, enter the name and description of the Session.

Note: If you chose a Metro Mirror Failover/Failback with Practice session, you are
asked for the parameters of the FlashCopy between H2 (target volume) and I2 (practice
volume), in addition to Name and Description.

You also are prompted if this FlashCopy is to be Incremental and for the background copy
rate, as shown in Figure 5-15 and Table 5-3 on page 291.

Figure 5-15 Metro Mirror with Practice: Session Properties window

4. In the Location Site 1 window, select the storage system that hosts the H1 volumes, as
shown in Figure 5-16 on page 296.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 295
 Figure 5-16 Metro Mirror Site 1 selection

5. In the Location Site 2 window, select the storage system that hosts the H2 and I2 volumes,
as shown in Figure 5-17.

Figure 5-17 Metro Mirror Site 2 selection

6. If the Results window shows that the session was successfully created, click Launch Add
Copy Sets Wizard. If the session was not created successfully, you should trouble shoot
the error message before you attempt to create the session again.
7. In the Select Host1 window of the Add Copy Sets wizard, select the storage system, I/O
Group, and Volume for the H1 volume, as shown in Figure 5-18 on page 297.

296 Tivoli Storage Productivity Center for Replication for Open Systems
 Optionally, use a CSV file to import copy sets (for more information, see “Importing CSV
files” on page 132).

Figure 5-18 Add Copy Sets wizard Choose Host1 volume

8. In the Choose Host2 window, select the storage system, I/O Group, and Volume for the H2
volume. Click Next to continue.
If you selected a Metro Mirror Failover/Failback with Practice session in step 2, you see the
Select Intermediate2 window. Select the storage system, I/O Group, and Volume for the I2
volume, as shown in Figure 5-19. Click Next.

Figure 5-19 Add Copy Sets wizard Choose Intermediate2 volume

9. If the Matching was successful (as shown in Figure 5-19), the Select Copy Sets window
opens. Click Add More and repeat steps 7 and 8 (see Figure 5-18 on page 297 and
Figure 5-19) as needed. Click Next. You are prompted to reconfirm the number of Copy
Sets that you want to add to the Session and, if confirmed, perform the operation. A
message is shown with the Results. If the operation was successful, click Finish to close
the wizard. If the operation failed, open the Console window to review the error messages.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 297
5.5.3 Global Mirror sessions
The same considerations that are described in 5.5.2, “Metro Mirror sessions” on page 294,
are valid here for Global Mirror sessions. Complete the following steps:
1. In the main Tivoli Storage Productivity Center for Replication window, click Sessions →
Create Session.

Note: A comparable process was shown in 5.5, “Session Types and Setup” on
page 288, beginning with Figure 5-6 on page 289. The session creation process is
similar across all session types; therefore, not all panels are repeated here.

2. In the Choose Session Type window of the Create Session wizard, select the following
Hardware Type and one of the Asynchronous Session Types:
– Hardware Types:SAN Volume Controller:
• Storwize Family
• Storwize V7000 Unified
– Session Types:Global Mirror Single Direction:
• Global Mirror Failover/Failback
• Global Mirror Failover/Failback with Practice
• Global Mirror Failover/Failback with Change Volumes
Click Next.
3. In the Properties window, enter a name and description for the session and, depending on
the chosen session type, set up the following parameters:
– If you chose a Global Mirror Failover/Failback with Practice session you also are
prompted for the parameters of the FlashCopy between Host Volume 2 (H2) and
Intermediate Volume 2 (I2), if this FlashCopy is to be Incremental, and the background
copy rate. These parameters are the same as those for the Metro Mirror
Failover/Failback with Practice that is shown in Figure 5-15 on page 295.
– If you chose a Global Mirror Failover/Failback with Change Volumes session, you are
prompted for the Change Volumes tunable parameters. Selecting the Enable Change
Volumes option (see Figure 5-20 on page 299) enables Change Volumes when the
session is created. The Cycle period value gives you the interval of FlashCopy
operations between H1-C1 and H2-C2 (the default value is 300 seconds or 5 minutes).
The Recovery Point Objective Alerts values give you the RPO threshold values that
Tivoli Storage Productivity Center for Replication uses to send Warning or Severe
alerts. A value of zero disables such alerts, as shown in Figure 5-20 on page 299.

Note: Cx is the abbreviation for Change volume and Hx is the abbreviation for Host
volume. For more information about the volume types and the abbreviations that are
used by Tivoli Storage Productivity Center for Replication, see 1.2, “Terminology” on
page 3.

298 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 5-20 Global Mirror Failover/Failback w/ Change Volumes Properties

4. In the Location Site 1 window, select the storage system that hosts H1 volumes.
If you chose a Global Mirror Failover/failback with Change volume, this storage system
also hosts the Change Volumes C1.
5. In the Location Site 2 window, select the storage system that hosts H2 volumes.
If you chose a Global Mirror Failover/failback with Practice volume, this storage system
also hosts the Practice Volumes I2.
If you chose a Global Mirror Failover/failback with Change volumes, this storage system
also hosts the Change Volumes C2.
6. If the Results window shows that the session was successfully created, click Launch Add
Copy Sets Wizard.
7. In the Choose Host1 window of the Add Copy Sets wizard, select the storage system, I/O
Group, and Volume for the H1 volume, as shown in Figure 5-21 on page 300. Click Next.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 299
 Figure 5-21 Add Copy Sets Choose Host1 volume

If you chose a Global Mirror Failover/failback with Change volumes in step 2, you see the
Choose Change1 volume window, as shown in Figure 5-21. Select the storage system, I/O
Group, and Volume for the C1 volume. Click Next.
Optionally, you can use a CSV file to import copy sets. For more information, see
“Importing CSV files” on page 132.
8. In the Choose Host2 window, select the storage system, I/O Group, and Volume for the H2
volume. Click Next to continue.
If you selected a Metro Mirror Failover/Failback with Practice session in step 2, you see the
Select Intermediate2 window. Select the storage system, I/O Group, and Volume for the I2
volume. Click Next.
If you chose a Global Mirror Failover/Failback with Change volumes in step 2, you see the
Choose Change2 Volume window. Select the storage system, I/O Group, and Volume for
the C2 volume. Click Next.
9. If the Matching was successful, you see the Select Copy Sets window. Click Add More
and repeat step 7 (see Figure 5-21) and step 8 as needed. Click Next. The wizard
prompts you to reconfirm the number of Copy Sets that you want to add to the session
and, if confirmed, perform the actual operation. A message is shown with the results. If the
operation was successful, click Finish to close the wizard. Open the Console window to
review the error messages if the operation failed.

300 Tivoli Storage Productivity Center for Replication for Open Systems
5.6 Why and when to use certain session types
The choice of session type depends on your company or business’ Disaster Recovery (DR)
plan and the level of protection that is required for each application and service. If you still do
not have a DR plan, consider preparing a preliminary DR plan. In this section, we provide an
overview about the basic selection criteria.

5.6.1 When to use FlashCopy

FlashCopy creates a point-in-time copy of volumes that can be used by other servers and
applications independently of the original source volumes. Because the FlashCopy operation
is fast, production I/O can be quiesced for brief periods without disrupting applications and
users, thus enabling the Flash operation to produce a consistent copy of the original set of
volumes.

FlashCopy sessions do not perform data replication to another site; source and target
volumes exist in the same storage system. In most cases, FlashCopy alone is not a suitable
option for disaster recovery. However, it can be associated with other tools for disaster
recovery, such as off-site tape backup vaulting, or even improve resources usage. An
example is application testing or online database backup by using Tivoli Storage Manager
Transparent Data Protection. For more information, see 5.4.1, “Global Mirror Failover/Failback
with Change Volumes session” on page 287.

5.6.2 When to use Metro Mirror

Metro Mirror performs a synchronous copy of volumes between separate storage systems. By
definition, synchronous replication makes the issuing host wait for its write I/Os to complete at
the local and remote storage systems, which for the remote systems include round-trip
network delay.

The main goal when Metro Mirror is used is to achieve zero Recovery Point Objective (RPO);
that is, zero data loss. Metro Mirror replication is the better choice whenever the distance
between the sites that are hosting the replicating storage systems falls within metropolitan
distances (under 300 km) and the application software can withstand longer I/O latencies
without severely degrading performance.

Metro Mirror typically requires faster, larger-bandwidth links between sites. For campus-wide
distances (up to 10 km), this can be achieved with native Fibre Channel long-wave links by
using dark fibers or dense wavelength division multiplexing (DWDM). However, when Network
Service Providers are used, the cost of such fast, high-bandwidth links can make Metro Mirror
cost-prohibitive for applications that tolerate greater than zero RPO.

5.6.3 When to use Global Mirror

Global Mirror performs an asynchronous copy between separate storage systems. Write I/O
operations are acknowledged when they can be committed to the local storage system,
sequence-tagged, and then passed on to the replication network. They do not wait for remote
storage acknowledgement.

Global Mirror can be used with farther distances between sites (up to 8000 km) without
compromising performance on the application software in the local site. However, it does
move your RPO to a value greater than zero.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 301
 Global Mirror with Change Volumes
Enabling change volumes moves your RPO to an even greater value; but, at the same time,
you can use a smaller bandwidth between sites, depending on the difference between peak
and average I/O workload during cycle periods.

5.7 Disaster Recovery use cases

In this section, we describe some alternative topologies for SAN Volume Controller or
Storwize implementation and how these topologies relate to Tivoli Storage Productivity
Center for Replication.

5.7.1 SAN Volume Controller Stretched Cluster

SAN Volume Controller Stretched Cluster (also known as Split Cluster or Split I/O Group) is
an implementation topology where the individual nodes of each SAN Volume Controller I/O
group in a cluster are placed in separate sites or failure domains. This topology requires a
minimum of three sites or failure domains, each one with at least one storage system that is
managed by the SAN Volume Controller cluster. The storage system in the site without SAN
Volume Controller nodes host the active SAN Volume Controller quorum disk. Figure 5-22
shows one example of such topology that uses no Inter-Switch Link (ISL) between switches.

Figure 5-22 Two-node SAN Volume Controller Stretched Cluster topology example

Note: This scenario is only possible with SAN Volume Controller because other members
of the Storwize family have both nodes of an I/O group physically inside the same controller
canister.

The SAN Volume Controller Stretched Cluster is a fault-tolerant, high-availability solution.

Metro Mirror and Global Mirror are disaster recovery solutions. Table 5-4 on page 303 shows
their functional differences.

302 Tivoli Storage Productivity Center for Replication for Open Systems
 Table 5-4 SAN Volume Controller Stretched Cluster and Metro/Global Mirror comparison
Feature Stretched Cluster Metro/Global Mirror

Failover Automatic and transparent Manual Failover, MM/GM

failover, volume LUNid source, and target volume
unchanged LUNids are different

Resynchronization Automatic Manual, power fail consistency

Consistency across multiple Not applicable; each volume Consistency groups across
volumes mirror has individual multiple volumes available
consistency

Server I/O performance impact Response time similar to Metro Mirror performs
over long distances synchronous copy because of synchronous replication,
cache mirroring between both response time depends on
sites distance; Global Mirror is
asynchronous, response time
independent from distance

For more information about SAN Volume Controller Stretched Cluster, see IBM Techdoc
WP102134 IBM SAN Volume Controller 7.1 SVC cluster spanning multiple data centers
(Stretched Cluster / Split I/O group), WP102134, which is available at this website:

http://w3-03.ibm.com/support/techdocs/atsmastr.nsf/WebIndex/WP102134

SAN Volume Controller Stretched Cluster and Tivoli Storage

Productivity Center for Replication
A SAN Volume Controller Stretched Cluster is seen and handled by Tivoli Storage
Productivity Center for Replication as one single storage entity, no different from its classical
cluster configuration with all nodes and I/O groups physically in the same rack.

Tip: High-availability solutions that use SAN Volume Controller Stretched Cluster use
primarily SAN Volume Controller Volumes Mirroring, which is not managed by Tivoli
Storage Productivity Center for Replication. To manage SAN Volume Controller Volumes
Mirroring, use Tivoli Storage Productivity Center or SAN Volume Controller management
tools (GUI or CLI).

The use of SAN Volume Controller in a stretched cluster often requires extensive use of
volumes with at least one mirrored copy. The use of FlashCopy or Global/Metro Mirror in this
situation means that even more copies of the same data are created. Even if you use
thin-provisioned volumes, more storage capacity is required.

Considerations are different depending on the session type when Tivoli Storage Productivity
Center for Replication is used with a SAN Volume Controller Stretched Cluster.

FlashCopy sessions
For SAN Volume Controller Stretched Cluster, a typical volume has two mirrored copies, one
in each failure domain. Therefore, each copy is physically hosted by a different managed
storage system in the SAN Volume Controller cluster. One of these copies is the primary
copy, with all read I/O being performed on it and all write I/O being performed first on it then
replicated to the other copies. We advise that you configure these mirrored volumes with the
primary copy in the same failure domain as the volume preferred node.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 303
 When you are configuring a FlashCopy session with the source volume as one such mirrored
volume, the configuration and placement of the target volume depends on the use you intend
to make of it.

If your FlashCopy target is intended as a point-in-time backup copy for quick restore if
required and it is not mapped to other servers, you might want to configure this target volume
and its preferred node in the same failure domain as the secondary mirror copy. Care should
be taken with the use of storage capacity in the failure domains. If your servers are
concentrated in one failure domain, the other requires much more available capacity, as
shown in Figure 5-23.

Figure 5-23 SAN Volume Controller Stretched Cluster with FlashCopy target in failure Domain 2

If you intend to use your FlashCopy target volume by another server or application (for
example, tape backup or application test), consider placing this target volume in the same
failure domain as this alternative server. Be careful if your servers are concentrated in one
failure domain because this might cause the SAN Volume Controller node in this domain to
become overloaded, as shown in Figure 5-24.

Figure 5-24 SAN Volume Controller Stretched Cluster with FlashCopy target with alternative server

Set the FlashCopy source volume attribute -mirrorwritepriority to redundancy.

304 Tivoli Storage Productivity Center for Replication for Open Systems
 It is unlikely that you want the target FlashCopy volume to be mirrored across failure domains
(it would be the fourth copy of the same data). Consider carefully if you have a possible
recovery scenario that might require this other mirroring.

Metro Mirror and Global Mirror sessions

With Metro Mirror and Global Mirror sessions, a target storage system is required. Consider
the following points:
򐂰 Except for Storwize V3500, the target system can be any member of the Storwize family.
򐂰 When another SAN Volume Controller cluster is used as the target system, it can be a
Stretched Cluster or not.
򐂰 When the Metro Mirror session is used, this target SAN Volume Controller system can be
placed in failure domain 3, which is co-located with the Storage System that hosts the
active quorum disk. In this scenario, this SAN Volume Controller target system can be the
Metro Mirror target system and host of the active quorum disk at the same time, as shown
in Figure 5-25.

Note: Although you can set up a topology that includes three or four different sites by
using stretched cluster and Metro or Global Mirror, do not confuse this scenario with
other session types that involve three or more sites, such as Metro Global Mirror, which
is available for DS8000. Tivoli Storage Productivity Center for Replication treats a SAN
Volume Controller stretched cluster as a single storage system (as source or target) in
a session.

Figure 5-25 Metro Mirror between a SAN Volume Controller stretched cluster and a Storwize V7000

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 305
5.7.2 Global Mirror Forwarding I/O Group
The Forwarding I/O Group is an alternative way to configure the SAN zoning between the
local and remote Storwize systems. Instead of making all of your Storwize local nodes
communicate with all of your remote nodes, you can elect one or more I/O groups on each
site and include only these I/O Groups in your Global Mirror zones. The local SAN Volume
Controller or V7000 detects which nodes have inter-cluster links, and any Global Mirror I/O
are forwarded to these nodes before the I/O is sent to the remote system, as shown in
Figure 5-26.

Note: This topology has as a prerequisite of more than one I/O group in either or both of
your Storwize paired systems.

Figure 5-26 SAN Volume Controller or Storwize Forwarding I/O Group

The use of a Global Mirror Forwarding I/O group has the advantage of the chances of hosts
that are attached to the other I/O groups face degradation on their I/O are greatly reduced
should your WAN face any congestion and consequentially buffer credit starvation.

For more information about Forwarding I/O Groups and how to set them up, see Chapter 12
of IBM System Storage SAN Volume Controller and Storwize V7000 Replication Family
Services, SG24-7574-02.

Note: Tivoli Storage Productivity Center for Replication does not play any role in
Forwarding I/O Group setup. This is done by changing SAN zoning configuration before
you get the Storwize systems paired for remote replication. After the pairing is done, you
can create your Global Mirror sessions normally in Tivoli Storage Productivity Center for
Replication and these sessions use the Forwarding I/O Group topology.

306 Tivoli Storage Productivity Center for Replication for Open Systems
5.8 Troubleshooting
A problem with a replication session often means that this session went to a state that was
unexpected, unwanted, or both. Troubleshooting these problems might require gathering
more information than Tivoli Storage Productivity Center for Replication alone can give you.
Experience shows that, in these cases, the more data that you have for cross-reference, the
better your chances are of establishing the root cause of your replication problem and fixing it.

In this section, we describe how to interpret the information Tivoli Storage Productivity Center
for Replication gives you regarding a troubled replication session, and how to cross-reference
this information with other information sources, such as Tivoli Storage Productivity Center,
storage systems, and SAN switches.

Note: It can be helpful to review the logs of Storage Systems and SAN switches directly to
collect them for cross-reference. However, as described in 5.1.2, “Tivoli Storage
Productivity Center for Replication and the Storwize family” on page 281, after you started
managing these devices by using Tivoli Storage Productivity Center for Replication or
Tivoli Storage Productivity Center, do not change their replication configuration by using
the Storage System’s own GUI or CLI unless you are instructed to do so by IBM Support.

For more information about possible replication services problems on the Storwize family, see
Chapter 13, “Troubleshooting Replication Family Services” of IBM System Storage SAN
Volume Controller and Storwize V7000 Replication Family Services, SG24-7574-02.

5.8.1 Storwize family replication error codes

Table 5-5 provides a description of commonly seen replication error codes in the Storwize
family when an error occurs.

Table 5-5 Storwize replication error codes

Error 1720: In a Metro Mirror or Global Mirror operation, the relationship has stopped and lost
synchronization, for a reason other than a persistent I/O error.

Possible Cause Suggested additional information

Intercluster SAN/WAN link failed Examine the following SAN switches and router
logs for evidence of link trouble:
򐂰 Brocade fabriclog
򐂰 Cisco show logging log

Destination Storwize cluster instability Examine the event logs of the destination cluster
to determine whether it had problems around the
time of your error condition.

Metro Mirror Destination Cluster Performance Check the performance of the destination cluster.

Check whether remote mDisks are responding

well.

Check whether CPUs of the remote nodes are

running over 80 percent.

Compare it with earlier performance statistics, if

available.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 307
 Error 1910: A FlashCopy mapping task was stopped because of the error that is indicated in
the sense data.

Related FlashCopy session stopped in Verify your Cascaded FlashCopy sessions

Cascaded FlashCopy

Error 1920: Global and Metro Mirror persistent error.

Insufficient WAN bandwidth 򐂰 Verify whether WAN link is overconfigured or

with poor quality
򐂰 Verify whether WAN link is driving more data
than it can handle

Performance issues at the remote cluster Check the performance of the destination cluster:

Check whether remote mDisks are responding

well.

Check whether CPUs of the remote nodes are

running over 80 percent.

Compare it with earlier performance statistics, if

available.

If an external storage system is used, verify its

error logs.

Metro Mirror or Global Mirror target volume is a Volumes in the Prepared state have write cache
FlashCopy source in Preparing or Prepared state in write-through mode, which reduces their write
performance.

Source volume or storage controller overloaded Collect and verify Storwize performance data at
the time the error occurred.

5.8.2 Troubleshooting replication links

Problems that are encountered by your replication sessions and might be traced back to your
replication links often occur because of the following causes:
򐂰 Your replicated Storage Infrastructure grew in capacity or I/O demand, and the replication
link bandwidth did not grow.
򐂰 Other applications and services started using the replication link for inter-site
communication.
򐂰 The quality of service (QoS) of the replication link was reduced for some reason.
򐂰 Changes in networking devices (SAN or IP), such as firmware update or configuration,
caused an unexpected impact.
򐂰 Changes in replication session parameters caused more data to be transmitted over the
replication link.

A good starting point to debug replication link problems is to use Tivoli Storage Productivity
Center for Replication to trace back when the problems with your sessions began. You can
also check your Problem and Change Management tool or network device logs for evidence
of events right before the problems started that might be related to the behavior you are
experiencing. Also,

308 Tivoli Storage Productivity Center for Replication for Open Systems
 For more information about how to troubleshoot your network devices and links, see Chapter
13, “Troubleshooting Replication Family Services” of IBM System Storage SAN Volume
Controller and Storwize V7000 Replication Family Services, SG24-7574-02.

Chapter 5. Tivoli Storage Productivity Center for Replication with SAN Volume Controller and Storwize family 309
310 Tivoli Storage Productivity Center for Replication for Open Systems
 6

Chapter 6. Using Tivoli Storage Productivity

Center for Replication with XIV
In this chapter, we describe the Tivoli Storage Productivity Center for Replication 5.2 features
that are related to IBM XIV Storage Systems (XIV).

Support: Support for XIV is available starting with Tivoli Storage Productivity Center for
Replication 4.2.2. Tivoli Storage Productivity Center 5.2 supports only XIV Gen2 hardware
and XIV Gen3 hardware.

This chapter includes the following topics:

򐂰 Overview
򐂰 Snapshot sessions
򐂰 Metro Mirror Failover/Failback sessions
򐂰 Global Mirror Failover/Failback sessions
򐂰 Adding XIV volume protection
򐂰 Disaster Recovery use cases
򐂰 Troubleshooting

© Copyright IBM Corp. 2014. All rights reserved. 311

6.1 Overview
As of Tivoli Storage Productivity Center for Replication 4.2, you can manage copy services
solutions on IBM XIV storage systems. XIV support is included as a part of Tivoli Storage
Productivity Center for Replication and does not require any other installation.

The following copy services terms that are related only to XIV storage systems are referenced
and described in this chapter:
򐂰 Consistency group
A set of volumes that is treated as a single volume.
򐂰 Mirror
A replica of a volume or consistency group to another volume or consistency group.
򐂰 Pool
An allocation of space that is used to create volumes.
򐂰 Snapshot
A point-in-time copy of a volume or consistency group.
򐂰 Snapshot group
A group of snapshots that is formed from a consistency group.

On XIV storage systems, primary and secondary volumes are referred to as master (primary)
and subordinate (secondary) volumes. For more information about XIV Storage System Copy
Services, see IBM XIV Storage System Copy Services and Migration; SG24-7759, which is
available at this website:

http://www.redbooks.ibm.com/redpieces/abstracts/sg247759.html?Open

6.1.1 XIV consistency groups

All session types in Tivoli Storage Productivity Center for Replication use XIV consistency
groups. The consistency groups are created and named by Tivoli Storage Productivity Center
for Replication. To determine the consistency group name for a session, we use the following
approach:
1. Use the Tivoli Productivity Center for Replication session name (limited to 58 characters).
2. If that name exists, use the session name with “_001” appended.
3. Keep trying “_00x” names up to x=30.
4. If all of those names exist, the consistency group is not created.

Because of this naming convention, the consistency group names that are created might not
be the same between XIV storage systems in a single session. For example, you can have a
consistency group that is named mmSession_001 on one XIV and a consistency group that is
named mmSession_002 on the other. The consistency group name depends on what
consistency groups exist on the individual XIV storage systems at the time Tivoli Storage
Productivity Center for Replication attempts to create them.

The consistency group name is shown in the Session Details panel, as shown in Figure 6-1
on page 313. By using this panel, you can see what is used on the XIV Storage System,
which can be important for debugging any issues.

312 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 6-1 Consistency groups that are listed in Session Details

You can also see the consistency group name in the Console log as it is created, as shown in
Figure 6-2.

Figure 6-2 Consistency group creation that is logged in the console

6.1.2 XIV connections

To add a connection to an XIV Storage System, from the menu select Storage Systems →
Add Storage Connection. This starts a wizard for adding a storage connection for all of the
supported storage system device types. When you select the XIV icon, you are prompted to
enter connection information, which includes a single IP address to the XIV Storage System,
a user name, and a password, as shown in Figure 6-3. The XIV user must have storage
administrator authority.

Figure 6-3 Add a single IP address for the XIV connection

Tip: When you add the IP address of an XIV Storage System, you get three connections
between it and Tivoli Storage Productivity Center for Replication. You do not need to enter
all three IP addresses.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 313
 After you complete the wizard to add the storage system, an SSH connection is established
and the XIV appears in the list of connections, as shown in Figure 6-4.

Figure 6-4 Status of storage system connections

If the connection was successful, the storage system is listed under the Storage Systems tab,
as shown in Figure 6-5. It is also available for selection in the Add Copy Sets wizard for the
sessions.

Figure 6-5 Successfully added XIV storage systems

314 Tivoli Storage Productivity Center for Replication for Open Systems
Various panels within Tivoli Storage Productivity Center for Replication, such as those shown
in Figure 6-4 on page 314 and Figure 6-5 on page 314, display the Local Status for the added
XIV storage systems. This status represents the status of the main connection between the
Tivoli Storage Productivity Center for Replication server and the IP address that you added. It
does not include the status of the other IP connections to the XIV that are automatically
discovered.

To view the status for all of the connections to an XIV Storage System, select the radio button
for the host name or IP address that you added (the main connection), choose View/Modify
Connections Details from the list of actions, and click Go, as shown in Figure 6-6.

Figure 6-6 View/Modify Connection Details

If you prefer, you can choose to click the link to the host name to go directly to the Connection
Details panel (as shown in Figure 6-7 on page 316) for a particular device instead.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 315
 Figure 6-7 shows the Local Connection Status for the main IP address that you entered for
the XIV Storage System. It also lists other Module Connections on the right in the panel. The
other connections show the status of the connections to the other IP addresses that Tivoli
Storage Productivity Center for Replication found for the XIV Storage System.

Figure 6-7 Connection Details for multiple IP addresses

Connections: The connection status values are all independent and do not roll up to
provide an overall status value for the XIV Storage System. The other connections provide
redundancy and failover for the nodes of the storage system.

6.2 XIV session types

The following session types are available for XIV storage systems:
򐂰 Snapshot
򐂰 Metro Mirror Failover/Failback
򐂰 Global Mirror Failover/Failback

Note: There are no practice session types available for XIV storage systems.

In the following sections, we describe each session type and how to use it.

6.2.1 Snapshot sessions

Snapshot is a session type that creates a point-in-time copy of a volume or set of volumes
without having to define a specific target volume. The target volumes of a snapshot session
are automatically created when the snapshot is created.

The XIV Storage System uses advanced snapshot architecture to create many volume copies
without affecting performance. By using the snapshot function to create a point-in-time copy
and to manage the copy, you can save storage. With the XIV Storage System snapshots, no
storage capacity is used by the snapshot until the source volume (or the snapshot) is
changed.

316 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: The snapshot session type is only available for XIV storage systems.

Figure 6-8 shows a snapshot session in Tivoli Storage Productivity Center for Replication.

Figure 6-8 Snapshot session

Configuration
XIV snapshot session support is available with all Tivoli Storage Productivity Center editions.
You must have the following environment to work with snapshot sessions in Tivoli Storage
Productivity Center for Replication:
򐂰 One or more XIV storage systems, with pools and volumes configured
򐂰 IP connectivity between the XIV Storage System and the Tivoli Storage Productivity
Center for Replication server

Limitations
The XIV snapshot session has the following limitations:
򐂰 Session name is limited to 58 characters.
򐂰 Consistency group is limited to 128 volumes. This is not enforced by Tivoli Storage
Productivity Center for Replication.
򐂰 All volumes from a session must be in the same pool.
򐂰 Volumes that are mapped to a host cannot be deleted while mapped.
򐂰 Locked volumes are read-only.
򐂰 Snapshot groups can be automatically deleted. This is based on deletion priority and pool
space.

Creating a snapshot session

After you add connections to the XIV storage systems and meet the configuration
requirements, you are ready to start creating sessions and adding copy sets to them.
Complete the following steps to set up a snapshot session for data replication with Tivoli
Storage Productivity Center for Replication:
1. Select Sessions from the navigation tree and click Create Session to display the Create
Session wizard, as shown in Figure 6-9 on page 318. Choose XIV and Snapshot and
click Next.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 317
 Figure 6-9 Create snapshot session

2. As shown in Figure 6-10, enter Session name and description, and click Next.

Figure 6-10 Session Properties

318 Tivoli Storage Productivity Center for Replication for Open Systems
3. Choose the location for the session, as shown in Figure 6-11. Click Next.

Figure 6-11 Session Location

The Session is successfully created, as shown in Figure 6-12.

Figure 6-12 Create Session Result page

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 319
 Adding Copy Sets to snapshot session
After a session is defined, Tivoli Storage Productivity Center for Replication must know on
which volumes to act. Complete the following steps to add copy sets to the snapshot session:
1. To add copy sets on the XIV Storage System to your created session, on the Results page
of the Create Session wizard (see Figure 6-12 on page 319), click Launch Add Copy
Sets Wizard.
2. In the Add Copy Sets wizard, select the storage system, storage pool, and volume. Click
Next (see Figure 6-13).

Figure 6-13 Host Storage system selection page

320 Tivoli Storage Productivity Center for Replication for Open Systems
 If the Copy set matches were successful, click Next and you see the Select Copy Sets
page, as shown in Figure 6-14.

Figure 6-14 Copy Sets selection

3. Select the Copy Set that you want to add and click Next. On the Confirm page, click Next
to confirm. If the Copy Set was created, you see the Results page, as shown in
Figure 6-15.

Figure 6-15 Add Copy Set result page

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 321
 4. Click Finish and the wizard closes. You can see the new defined session in the Sessions
panel, as shown in Figure 6-16.

Figure 6-16 XIV snapshot session

Activating a snapshot session

After a session is defined, you can access its details and modify it from the Session Details
window, as shown in Figure 6-17. Because this session was not run, the details under
Snapshot Groups remain empty.

Figure 6-17 Detailed view of XIV snapshot session; inactive and has not yet run

322 Tivoli Storage Productivity Center for Replication for Open Systems
 Complete the following steps to activate the Tivoli Storage Productivity Center for Replication
snapshot session:
1. In the Session Details panel, click the pull-down list, select Create Snapshot, and then
click Go, as shown in Figure 6-18.

Figure 6-18 XIV Create snapshot

2. A new wizard opens. The actions that you are about to take on those volumes are
confirmed. Under Advanced Options, you also can modify various XIV specific values,
including the actual snapshot group name and deletion priority, as shown in Figure 6-19.

Figure 6-19 Confirmation of snapshot session activation and options

3. Make the appropriate selections and click Yes.

Tivoli Storage Productivity Center for Replication now runs the snapshot command on the
defined copy sets in the session, as shown in Figure 6-20 on page 324.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 323
Figure 6-20 Session is activated; XIV took the snapshot of the volumes in the Copy Set

Other Tivoli Storage Productivity Center for Replication snapshot

actions inside a session
After a snapshot session is defined, you can also take other actions as you can do from the
XIV GUI or XIV command-line interface (CLI,) such as a Restore operation, as shown in
Figure 6-21.

Figure 6-21 XIV snapshot session actions

324 Tivoli Storage Productivity Center for Replication for Open Systems
6.2.2 Metro Mirror Failover/Failback sessions
Metro Mirror is a method of synchronous, remote data replication that operates between two
sites that are up to 300 kilometers apart. You can use failover and failback to switch the
direction of the data flow.

Metro Mirror replication maintains identical data in the source and target. When a write is
issued to the source copy, the changes that are made to the source data are propagated to
the target before the write finishes posting. If the storage system fails, Metro Mirror provides
zero loss if data must be used from the recovery site.

If you are familiar with the use of the Metro Mirror session type with other supported storage
systems, you find the process within Tivoli Storage Productivity Center for Replication is
similar. In this section, we highlight areas that are unique to the XIV Storage System.

Figure 6-22 shows Metro Mirror session in Tivoli Storage Productivity Center for Replication.

Figure 6-22 XIV Metro Mirror session

Configuration
You must have the following environment to work with Metro Mirror sessions:
򐂰 Two or more XIV storage systems with pools and volumes configured.
򐂰 IP connectivity between the XIV storage systems and the Tivoli Storage Productivity
Center for Replication server.
򐂰 Remote mirroring connectivity that is configured for the two XIV storage systems in the
session.
򐂰 Matching volumes on the source and target XIV storage systems.
򐂰 All volumes are in same pool on each host site.

Reference: For more information about XIV System configuration, see the IBM XIV
Storage System User Manual, GC27-2213-02, which is available at this website:
http://publib.boulder.ibm.com/infocenter/ibmxiv/r2/topic/com.ibm.help.xiv.doc/d
ocs/GC27-2213-02.pdf

Limitations
The XIV Metro Mirror session has the following limitations:
򐂰 Session name is limited to 58 characters.
򐂰 Consistency group is limited to 128 volumes. This is not enforced by Tivoli Storage
Productivity Center for Replication.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 325
 򐂰 All volumes from a session must be in the same pool.
򐂰 Volumes that are mapped to a host cannot be deleted while they are mapped.
򐂰 Locked volumes are read-only.
򐂰 XIV hardware is limited to 512 mirroring relationships.

Creating a Metro Mirror session

To set up Metro Mirror for snapshots, you must create and define a session for this type of
Copy Service, add the XIV volumes from both XIVs to this newly defined session, and
activate the session.

The XIV pool and volumes must be defined by using the XIV GUI or XIV CLI before Tivoli
Storage Productivity Center for Replication is used for this process.

Complete the following steps to define a XIV Metro Mirror session:

1. In the Tivoli Storage Productivity Center for Replication, browse to the Sessions panel and
click Create Session.

Note: A comparable process was shown in “Creating a snapshot session” on page 317,
beginning with Figure 6-9 on page 318. The session creation process is similar across
all session types; therefore, not all panels are repeated here.

2. Select the XIV as the storage type and click Next.

3. Define the Tivoli Storage Productivity Center for Replication session type, as shown in
Figure 6-23. In the red box in the upper right section of the panel is an icon that changes
according to the session types. The session wizard also varies slightly, depending on the
session type that is defined.

Figure 6-23 Tivoli Storage Productivity Center for Replication Session wizard: Metro Mirror option

Select Metro Mirror Failover/Failback, and click Next to proceed with the definition of the
session properties.

326 Tivoli Storage Productivity Center for Replication for Open Systems
4. In the Properties panel that is shown in Figure 6-24, enter a Session name (required) and
a Description (optional) and click Next.

Figure 6-24 Properties panel

5. In the Site Locations panel that is shown in Figure 6-25, from the Site 1 Location
drop-down menu, select the site of the first XIV. The list shows the various sites that are
defined. Click Next.

Figure 6-25 Site Locations panel

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 327
 6. Define the secondary or target site, as shown in Figure 6-26. From the Site 2 Location
drop-down menu, select the appropriate target or secondary site that has the target XIV
and corresponding volumes. Click Next.

Figure 6-26 Site location for secondary site

Tivoli Storage Productivity Center for Replication creates the session and displays the
result, as shown in Figure 6-27.

Figure 6-27 New Metro Mirror session

328 Tivoli Storage Productivity Center for Replication for Open Systems
 7. Click Finish to view the session, as shown in Figure 6-28.

Figure 6-28 Metro Mirror session without any copy sets

Defining and adding copy sets to a Metro Mirror session

After a Metro Mirror session is defined, the XIV volumes must be specified for that session.
Complete the following steps:
1. The Copy Sets wizard features various dependent drop-down menus, as shown in
Figure 6-29. Select the XIV in the first site, the pool, and the first volume you want to have
as part of the Metro Mirror copy set. Click Next.

Figure 6-29 Add Copy Sets wizard for Metro Mirror

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 329
 2. Make the appropriate selections for site 2 (target site), as shown in Figure 6-30. Click
Next.

Figure 6-30 Target panel for the first volume of the Copy Set wizard

3. Add volumes to the Copy Sets. Figure 6-31 shows the first volume that is defined for the
Copy Set.

Figure 6-31 Confirming first volume selection for this Copy Set

4. You can add a second volume to the copy set. Depending on your business needs, you
might have several volumes (all within the same pool at each XIV) in one copy set, or
individual volumes.

330 Tivoli Storage Productivity Center for Replication for Open Systems
 To add another volume, click Add More. Tivoli Storage Productivity Center for Replication
tracks the first volume, as you see when you complete the wizard.
5. Figure 6-32 shows the second volume that we are adding to the copy set (we also
selected the same values for the primary XIV and pool). Make the appropriate selections
and click Next.

Figure 6-32 Adding a second volume to Copy Set

6. The wizard prompts for the secondary XIV values, as shown in Figure 6-33. Make the
appropriate entries and click Next.

Figure 6-33 Copy Set wizard for second XIV and target volume selection panel

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 331
 The Copy Set wizard now has both volumes selected, and you can add more volumes, if
required, as shown in Figure 6-34. Click Next.

Figure 6-34 Two Copy Sets in Metro Mirror Session

Note: If you must add a large set of volumes, you can import the volume definitions and
pairings from a comma-separated variable (.csv) file. For more information, see the
Tivoli Productivity Center Information Center, which is available at this website:

http://pic.dhe.ibm.com/infocenter/tivihelp/v59r1/index.jsp?topic=%2Fcom.ibm.
tpc

7. Tivoli Storage Productivity Center for Replication confirms that the volumes are added to
the set, as shown in Figure 6-35. Click Next.

Figure 6-35 Copy Set wizard prompt for confirmation of the addition of both volumes to set

332 Tivoli Storage Productivity Center for Replication for Open Systems
 Tivoli Storage Productivity Center for Replication updates its repository and indicates the
progress of the update, as shown in Figure 6-36.

Figure 6-36 Progress of updating repository

After Tivoli Storage Productivity Center for Replication completes the Copy Set process,
the Results panel opens and you can click Finish, as shown in Figure 6-37.

Figure 6-37 Results panel

8. Click Finish. The updated Session Details window opens, as shown in Figure 6-38.

Figure 6-38 Metro Mirror Session details at the completion of both wizards

Activating Tivoli Storage Productivity Center for Replication Metro

Mirror session
Now that you defined a session and added a copy set that contains volumes, you can move
on to the next phase, and activate the session by completing the following steps:
1. From the Select Action menu, select Start H1 → H2, and click Go to activate the session,
as shown in Figure 6-39 on page 334.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 333
 Figure 6-39 Action items that are available to the Metro Mirror Session

2. You are prompted for confirmation, as shown in Figure 6-40. Click Yes.

Figure 6-40 Last warning before taking the Metro Mirror Session active

After the Tivoli Storage Productivity Center for Replication commands are sent to the XIV,
Tivoli Storage Productivity Center for Replication continues to update the same Session
Details window to reflect the latest status, as shown in Figure 6-41 and Figure 6-42 on
page 335. After the synchronization, the status changes to Normal status.

Figure 6-41 Progress actions for Metro Mirror session: Part 1

334 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 6-42 Various progress actions for Metro Mirror session: Part 2

Suspending the Metro Mirror session

At some point, you might want to suspend the Metro Mirror session. This might be dictated by
various business reasons or physical issues, such as a communication link failure, or a true
site outage. Suspending the Mirror session also is the first step for allowing the target
volumes to be accessible, and reversing the actual mirror direction.

To make the target volumes available, you must access the Session and perform a Suspend
and then Recover. Complete the following steps:
1. Browse to the Session Details panel and select Suspend, as shown in Figure 6-43. Click
Go to start the Suspend action.

Figure 6-43 Suspend action

A confirmation window opens in which you are warned about the Suspend action, as
shown in Figure 6-44 on page 336. Click Yes to proceed.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 335
 Figure 6-44 Warning

The updated Session Details window opens as a result of the Suspend action, as shown
in Figure 6-45.

Figure 6-45 Tivoli Storage Productivity Center for Replication Metro Mirror Session being suspended

2. After you suspend a Metro Mirror link, you can perform a Recover operation, which causes
Tivoli Storage Productivity Center for Replication to reverse the link and begins to move
information from the Target/Slave volume back to the Master/Primary volume.
This process is also known as moving data from the Secondary back to the Primary. Tivoli
Storage Productivity Center for Replication can complete this process only after the link is
suspended.
Make note of the difference in the Session Details window that is shown in Figure 6-46 in
which the Recover action is allowed because the link was suspended. Select Recover and
then click Go.

Figure 6-46 Session Details panel that shows the Recover option is available

336 Tivoli Storage Productivity Center for Replication for Open Systems
 3. Tivoli Storage Productivity Center for Replication prompts you to confirm the operation, as
shown in Figure 6-47. Click Yes.

Figure 6-47 Final confirmation before the link for Metro Mirror Session is reversed

Tivoli Storage Productivity Center for Replication now prepares both XIVs for the
upcoming role change. This makes the target volumes immediately available, as shown in
Figure 6-48.

Figure 6-48 Target available status

4. You also have the option of replacing and updating the Primary/Master volume with
information from the Target/Slave volume (Production Site Switch). From the Select Action
drop-down menu, select Enable Copy to Site 1, as shown in Figure 6-49 on page 338.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 337
 Figure 6-49 Preparing to reverse link

The icon has the blue triangle over H2, which indicates that the mirror session switched
and Site 2 is now active.
5. Click Go, and then confirm the selection (see Figure 6-50), which causes Tivoli Storage
Productivity Center for Replication to send the appropriate commands to both XIVs.

Figure 6-50 Confirm Enable Copy to Site 1 of the Metro Mirror session

6. After the reversal, you must activate the link, which is shown as the Start H2 → H1 menu
choice that is now available in the drop-down menu that is shown in Figure 6-51 on
page 339. Click Go and confirm to have Tivoli Storage Productivity for Replication activate
the link in reverse.

338 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 6-51 Metro Mirror before the link was activated in the reverse direction

Figure 6-52 shows that Tivoli Storage Productivity for Replication activated the link in reverse,
and that the volumes fully replicated themselves back to the original source volumes.

Figure 6-52 Metro Mirror Session fully reversed and completed

In this example, the secondary volumes are available for immediate production usage and
replication back to the old master.

6.2.3 Global Mirror Failover/Failback sessions

Global Mirror is a method of asynchronous, remote data replication that operates between
two sites at longer distances. You can use failover and failback to switch the direction of the
data flow.

The data on the target often is written a few seconds after the data is written to the source
volumes. When a write is issued to the source copy, the change is propagated to the target
copy, but subsequent changes are allowed to the source before the target verifies that it
received the change. Because consistent copies of data are formed on the secondary site at
set intervals, data loss is determined by the amount of time since the last consistency group
was formed. If your system stops, Global Mirror might lose some data that was being
transmitted when the disaster occurred. Global Mirror still provides data consistency and data
recoverability if there is a disaster.

If you are familiar with the use of the Global Mirror session type with other supported storage
systems, you find the process within Tivoli Storage Productivity Center for Replication to be
similar. In this section, we highlight areas that are unique to the XIV Storage System.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 339
 Figure 6-53 shows Global Mirror session in Tivoli Storage Productivity Center for Replication.

Figure 6-53 XIV Global Mirror session

Configuration
You must have the following environment to work with Global Mirror sessions:
򐂰 At least two XIV storage systems, with pools and volumes configured
򐂰 IP connectivity between the XIV storage systems and the Tivoli Storage Productivity
Center for Replication server
򐂰 Remote mirroring connectivity that is configured for the two XIV storage systems in the
session
򐂰 Matching volumes on the source and target XIV storage systems
򐂰 All volumes in same pool on same site

Reference: For more information about XIV System configuration, see the IBM XIV
Storage System User Manual, GC27-2213-02, which is available at this website:
http://publib.boulder.ibm.com/infocenter/ibmxiv/r2/topic/com.ibm.help.xiv.doc/d
ocs/GC27-2213-02.pdf

Limitations
The XIV Metro Mirror session includes the following limitations:
򐂰 Session name is limited to 58 characters.
򐂰 Consistency group is limited to 128 volumes. This is not enforced by Tivoli Storage
Productivity Center for Replication.
򐂰 All volumes from a session must be in the same pool.
򐂰 Volumes that are mapped to a host cannot be deleted while they are mapped.
򐂰 Locked volumes are read-only.
򐂰 XIV hardware is limited to 512 mirroring relationships.

Creating a Global Mirror session

To use Tivoli Storage Productivity Center for Replication for any type of XIV Copy Services
(including the asynchronous mirror capabilities of XIV), you first must create and define a
session, add the XIV volumes to that session, and activate the session.

The process for setting up Tivoli Storage Productivity Center for Replication Global Mirror with
XIV is nearly identical to what was already described in “Creating a Metro Mirror session” on
page 326.

340 Tivoli Storage Productivity Center for Replication for Open Systems
The XIV pool and volumes must be defined by using the XIV GUI or CLI before Tivoli Storage
Productivity Center for Replication is used for this process. At the time of this writing, XIV
pools or volumes cannot be created from Tivoli Storage Productivity Center for Replication.

Complete the following steps to define a Tivoli Storage Productivity Center for Replication
session for asynchronous mirroring:
1. In the Tivoli Storage Productivity Center for Replication GUI, browse to the Sessions
window and click Create Session. For more information, see the process that is shown
starting with Figure 6-24 on page 327.
2. When you are prompted for a session type, select Asynchronous; Global Mirror, as
shown in Figure 6-54. Click Next to start the process.

Figure 6-54 Asynchronous Session Type panel

3. Make the appropriate entries and selections in the panel, as shown in Figure 6-55 on
page 342.
The difference between Metro Mirror and Global Mirror sessions is that for Global Mirror,
Tivoli Storage Productivity Center for Replication asks for the Recovery Point Objective
(RPO) in seconds, and the selection box underneath prompts you for the scheduling
interval.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 341
 Figure 6-55 Asynchronous Properties; RPO options

4. Click Next to proceed through the wizard’s instructions to finish the process. This is the
same process that is described in , “Creating a Metro Mirror session” on page 326.

Defining and adding Tivoli Storage Productivity Center for Replication

copy sets to a Global Mirror session
This second phase of the Tivoli Storage Productivity Center for Replication process for Global
Mirror, adding copy sets, is identical to what is described in , “Defining and adding copy sets
to a Metro Mirror session” on page 329.

Activating the Tivoli Storage Productivity Center for Replication Global

Mirror session
This is the last phase of the process. You are now ready to activate the Global Mirror session.
From the drop-down action menu, select Start H1 → H2, and click Go to activate the session,
as shown in Figure 6-56.

Figure 6-56 Session Actions for Global Mirror

342 Tivoli Storage Productivity Center for Replication for Open Systems
 Suspending the Global Mirror session
Tivoli Storage Productivity Center for Replication treats Global Mirrors the same way as Metro
Mirrors. As describe in , “Suspending the Metro Mirror session” on page 335, you might want
to suspend, if not reverse, the Global Mirror session.

This reversal is done by using the same process that is described in , “Suspending the Metro
Mirror session” on page 335.

6.3 Adding XIV volume protection

Tivoli Storage Productivity Center for Replication has another protection function for storage
volumes, whereby you can restrict certain volumes from other Tivoli Storage Productivity
Center for Replication Sessions or Copy Sets.

Complete the following steps:

1. From the Storage Systems tab, select the XIV system and click Volume Protection, as
shown in Figure 6-57.

Figure 6-57 Select array and then Volume Protection

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 343
 2. Use the various drop-down menus that are shown in Figure 6-58 to select the pool and
volumes. The use of an asterisk (*) in the last input field returns a list of all of the volumes
that are in that pool. Optionally, you can use that field to filter the list of volumes that is
returned.

Figure 6-58 Choose Volumes panel

3. Click Next to display the volumes (as shown in Figure 6-59) and select the volumes that
you want to mirror.

Figure 6-59 Select Volumes panel

4. Click Next. Tivoli Storage Productivity Center for Replication ensures that the selected
volumes are protected from other Tivoli Storage Productivity Center for Replication
operations.

Important: These actions help inside the Tivoli Storage Productivity Center for Replication
system only. Any administrator who is accessing the XIV GUI directly is not informed of the
volume protections. They still see any snapshot or volume locks that are part of normal
operations, but not any of the protections that are described here.

344 Tivoli Storage Productivity Center for Replication for Open Systems
6.4 Disaster Recovery use cases
Tivoli Storage Productivity Center for Replication and XIV remote mirroring solutions (Metro
Mirror and Global Mirror) can be used to address various failures and planned outages, from
events that affect a single XIV system or its components, to events that affect an entire data
center or campus, or events that affect an entire geographical region.

When the production XIV system and the disaster recovery (DR) XIV system are separated
by increasing distance, disaster recovery protection for more levels of failures is possible, as
shown in Figure 6-60. A global distance disaster recovery solution protects against
single-system failures, local disasters, and regional disasters.

Figure 6-60 Disaster Recovery protection levels

The following configurations are possible:

򐂰 Single-site high-availability XIV Remote Mirroring configuration
Protection for the event of a failure or planned outage of an XIV system (single-system
failure) can be provided by a zero-distance high-availability (HA) solution, including
another XIV system in the same location (zero distance). Usage of this configuration is an
XIV synchronous mirroring solution that is part of an HA clustering solution, including
servers and XIV storage systems. Figure 6-61 shows a single-site HA configuration in
which both XIV systems are in the same data center.

Figure 6-61 Single site HA configuration

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 345
 򐂰 Metro region XIV Remote Mirroring configuration
Protection against the failure or planned outage of an entire location (local disaster) can
be provided by a metro distance disaster recovery solution (as shown in Figure 6-62),
which includes another XIV system in a different location within a metro region. The two
XIV systems might be in different buildings on a corporate campus or in different buildings
within the same city. Typical usage of this configuration is an XIV synchronous mirroring
solution.

Figure 6-62 Metro region disaster recovery configuration

򐂰 Out-of-region XIV Remote Mirroring configuration

Protection against a failure or planned outage of an entire geographic region (regional
disaster) can be provided by a global distance disaster recovery solution (as shown in
Figure 6-63), which includes another XIV system in a different location outside the metro
region. (The two locations might be separated by up to a global distance.) Typical usage of
this configuration is an XIV asynchronous mirroring solution.

Figure 6-63 Out-of-region disaster recovery configuration

346 Tivoli Storage Productivity Center for Replication for Open Systems
򐂰 Metro region plus out-of-region XIV mirroring configuration
Certain volumes can be protected by a metro distance disaster recovery configuration,
and other volumes can be protected by a global distance disaster recovery configuration,
as shown in Figure 6-64.

Figure 6-64 Metro region plus out-of-region configuration

Typical usage of this configuration is an XIV synchronous mirroring solution for a set of
volumes with a requirement for zero RPO, and an XIV asynchronous mirroring solution for
a set of volumes with a requirement for a low, but non-zero RPO. Figure 6-64 shows a
metro region plus out-of-region configuration.
Snapshots can be used with Remote Mirroring to provide copies of production data for
business or IT purposes. Moreover, when they are used with Remote Mirroring, snapshots
provide protection against data corruption.

As with any continuous or near-continuous remote mirroring solution, XIV Remote Mirroring
cannot protect against software data corruption because the corrupted data is copied as part
of the remote mirroring solution. However, the XIV snapshot function provides a point-in-time
image that can be used for rapid restore in the event of software data corruption that occurred
after the snapshot was taken. XIV snapshot can be used with XIV Remote Mirroring, as
shown in Figure 6-65 on page 348.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 347
 Figure 6-65 Combining snapshots with Remote Mirroring

Recovery by using a snapshot warrants deletion and re-creation of the mirror, as shown in the
following examples:
򐂰 XIV snapshot (within a single XIV system)
Protection against software data corruption can be provided by a point-in-time backup
solution by using the XIV snapshot function within the XIV system that contains the
production volumes.
򐂰 XIV local snapshot and Remote Mirroring configuration
An XIV snapshot of the production (local) volume can be used in addition to XIV Remote
Mirroring of the production volume when protection against logical data corruption is
required in addition to protection against failures and disasters. The other XIV snapshot of
the production volume provides a quick restore to recover from data corruption. Another
snapshot of the production (local) volume can also be used for other business or IT
purposes (for example, reporting, data mining, and development and test).
Figure 6-66 shows an XIV local snapshot plus Remote Mirroring configuration.

Figure 6-66 Local snapshot plus Remote Mirroring configuration

348 Tivoli Storage Productivity Center for Replication for Open Systems
 򐂰 XIV remote snapshot plus Remote Mirroring configuration
An XIV snapshot of the consistent replicated data at the remote site can be used in
addition to XIV Remote Mirroring to provide another consistent copy of data that can be
used for business purposes, such as data mining and reporting, and for IT purposes, such
as, remote backup to tape or development, test, and quality assurance. Figure 6-67 shows
an XIV remote snapshot plus Remote Mirroring configuration.

Figure 6-67 XIV remote snapshot plus Remote Mirroring configuration

6.5 Troubleshooting
Even with careful planning and execution, you might still encounter errors when you are
attempting data replication tasks. This section provides guidance for some of the common
errors that might occur.

Troubleshooting resources
The following files and tools can help you find more information when you are examining the
errors:
򐂰 Log package
The log package does not require direct access to the Tivoli Storage Productivity Center
for Replication file system. It contains logs with details regarding the actions in Tivoli
Storage Productivity Center for Replication, such as xivApiTrace.
򐂰 Tivoli Storage Productivity Center for Replication Console
The Console is a listing in the GUI of csmMessage.log that is on the Tivoli Storage
Productivity Center for Replication server. It can be opened by selecting Console from the
navigation tree.
Figure 6-68 shows a sample of the type of messages that are available in the Console. It
can be used to identify steps that succeeded and you can isolate the step that failed. It
also includes a historical reference of actions against the Tivoli Storage Productivity
Center for Replication server.

Figure 6-68 Sample Console listing

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 349
 It can also be accessed by using links that are provided during actions within the GUI. This
can be useful for providing more information at the time of the error. Click the (Open
Console) link, as shown in Figure 6-69.

Figure 6-69 Console link for a running action

You also can click the link to the message ID (for example, IWNR1026I) to open the
message description.

Troubleshooting issues with Metro Mirror and Global Mirror sessions

This section addresses some of the issues you might encounter with Metro Mirror and Global
Mirror sessions. Symptoms that you might see, example errors, and steps to resolve errors
are provided to aid you with troubleshooting.

Issue: Pool/snapshot size not large enough for global mirroring

This issue includes the symptoms that are shown in Example 6-1 and Example 6-2.

Example 6-1 With volume IO pair errors after starting session, all pairs go suspended
IWNR2055W [Aug 22, 2013 9:16:45 AM] The pair in session volumespace for copy set
XIV:VOL:7803441:100987 with source XIV:VOL:7803441:100987(io_todd_3) and target
XIV:VOL:7803448:101660(io_todd_3) in role pair H1-H2 was suspended due to a reason
code of Master_Pool_Exhausted, but was not yet consistent; no action was taken on
the session.

Example 6-2 Session after prepared moves severe/suspended on volume IO

IWNR2050E [Aug 22, 2013 9:48:42 AM] The pair in session testfullpool for copy set
XIV:VOL:7803441:100985 with source XIV:VOL:7803441:100985(io_todd_1) and target
XIV:VOL:7803448:101658(io_todd_1) in role pair H1-H2 was suspended unexpectedly
with a reason code of Master_Pool_Exhausted.

350 Tivoli Storage Productivity Center for Replication for Open Systems
Complete the following steps to resolve the issue:
1. Increase the size of the pool and snapshot space of the pool. The pool size must be more
than three times the I/O volumes total size for the pool. If there is enough pool space, the
snapshot space is not as important.
2. Refresh the configuration for the XIV Storage System.
3. Restart the session.

Issue: Consistency group name exists

All operations are successful and the session runs correctly. There are no specific errors for
this situation. The folloing snapshot options are available:
򐂰 Consistency group for the session is listed as <session name>_001.
XIV automatically increments existing names.
򐂰 This is a cosmetic issue unless volumes intended for the session are also in the
consistency group. (See the next troubleshooting topic.)

Complete the following steps to resolve this issue:

1. End the session.
2. Remove all of the volumes from the consistency group on the XIV.
3. Remove the consistency group on the XIV.
4. Restart the session.

Issue: Volume already is a part of consistency group

This issue includes the symptoms that are shown in Example 6-3.

Example 6-3 Pair errors after starting session: VOLUME_BELONGS_TO_CG

IWNR2108E [Aug 23, 2013 12:17:42 PM] A hardware error occurred during the running
of a command for the pair in session existingMM_CG for copy set
XIV:VOL:7803441:100985 with source XIV:VOL:7803441:100985(io_todd_1) and target
XIV:VOL:7803448:101658(io_todd_1) in role pair H1-H2. The hardware returned an
error code of VOLUME_BELONGS_TO_CG.

Complete the following steps to resolve this issue:

1. Remove all of the volumes from the existing consistency group on the XIV.
2. Restart the session.

Issue: Volume already is a part of mirroring relationship

This issue includes the symptoms that are shown in Example 6-4, Example 6-5 on page 352,
and Example 6-6 on page 352.

Example 6-4 Volume is in relationship: VOLUME_IS_MASTER/SLAVE

IWNR2108E [Aug 23, 2013 1:25:56 PM] A hardware error occurred during the running
of a command for the pair in session exisitingMirrors for copy set
XIV:VOL:7803441:100985 with source XIV:VOL:7803441:100985(io_todd_1) and target
XIV:VOL:7803448:101658(io_todd_1) in role pair H1-H2. The hardware returned an
error code of VOLUME_IS_MASTER.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 351
 Example 6-5 Volume is in relationship: VOLUME_HAS_MIRROR
IWNR2108E [Aug 23, 2013 1:41:46 PM] A hardware error occurred during the running
of a command for the pair in session exisitingMirrors for copy set
XIV:VOL:7803441:100986 with source XIV:VOL:7803441:100986(io_todd_2) and target
XIV:VOL:7803448:101659(io_todd_2) in role pair H1-H2. The hardware returned an
error code of VOLUME_HAS_MIRROR.

Example 6-6 Volume mirror copy set is wrong copy type

IWNR2512E [Aug 23, 2013 1:25:56 PM] The volume mirror copy set
XIV:VOL:7803441:100987 with source XIV:VOL:7803441:100987(io_todd_3) and target
XIV:VOL:7803448:101660(io_todd_3) in session exisitingMirrors existed on the
hardware but was not the right copy type.

Complete the following steps to resolve this issue:

1. Deactivate the mirror.
2. Remove the mirror.
3. Restart the session.

Issue: Volumes have existing snapshots/replications

This issue includes the symptoms that are shown in Example 6-7.

Example 6-7 Pair errors after starting the session

IWNR2108E [Aug 23, 2013 11:07:15 AM] A hardware error occurred during the running
of a command for the pair in session todd-mm for copy set XIV:VOL:7804988:580312
with source XIV:VOL:7804988:580312(io_todd_001) and target
XIV:VOL:1302136:107903(io_todd_001) in role pair H1-H2. The hardware returned an
error code of VOLUME_HAS_SNAPSHOTS.

Complete the following steps to resolve this issue:

1. Remove the existing snapshots and replications on the XIV.
2. Restart the session.

Issue: Sessions go severe because of XIV hardware link errors

This issue includes the symptoms that are shown in Example 6-8 and Example 6-9.

Example 6-8 Prepared session and pairs go suspended or suspend after starting session
IWNR2061E [Aug 23, 2013 7:41:37 AM] The pair was suspended on the hardware because
the source was disconnected from the target.

Example 6-9 Mirrors on XIV show RPO lagging

IWNR2750E [Aug 23, 2013 11:53:00 AM] Recovery Point Objective for session
todd-gm-connectiondown has passed the threshold of 30 seconds.

Complete the following steps to resolve the issue:

1. Re-establish the link between the XIV storage systems.
2. Resolve lagging issues between the XIV storage systems.
3. Sessions resolve on their own or you can restart the session.

352 Tivoli Storage Productivity Center for Replication for Open Systems
 Hardware troubleshooting: The following troubleshooting topics deal specifically with
hardware configuration changes that might occur.

Issue: Changes to volume and pool name or size

This issue includes the following symptoms:
򐂰 Pair errors after the session is started.
򐂰 Error returns BAD_NAME.

Complete the following steps to resolve the issue:

1. Refresh the configuration for the XIV Storage System.
2. Restart the session.

Issue: Changes to XIV hardware mirror relationships or consistency groups

This issue includes the following symptoms:
򐂰 Manually deactivate mirror; Tivoli Storage Productivity Center for Replication session is
suspended.
򐂰 Remove mirror relationships; Tivoli Storage Productivity Center for Replication session is
suspended.
򐂰 Remove volume from consistency group or group mirror; Tivoli Storage Productivity
Center for Replication session stays prepared, but it no longer has control of that volume
for future commands.

Support: Tivoli Storage Productivity Center for Replication does not support handling
any of these situations, but these situations usually are not unrecoverable.

Each situation is unique, but in most cases, restarting the session resolve any manual
manipulation of the hardware.

Issue: Changes to Global Mirror properties (RPO or Schedule)

There are no specific errors for this situation. You see the old values for RPO Threshold and
Sync Schedule when you are looking at the session properties or the hardware mirrors.

Tivoli Storage Productivity Center for Replication does not automatically pick up changes that
are made to Global Mirror properties on the hardware.

Complete the following steps to resolve the issue:

1. Change the properties in the Tivoli Storage Productivity Center for Replication session
panel.
2. Restart the session.

Chapter 6. Using Tivoli Storage Productivity Center for Replication with XIV 353
354 Tivoli Storage Productivity Center for Replication for Open Systems
 7

Chapter 7. Managing z/OS HyperSwap from

Tivoli Storage Productivity Center
for Replication for Open Systems

Tivoli Storage Productivity Center for Replication version 5.2 can open a connection to a z/OS
server from a Tivoli Storage Productivity Center for Replication distributed installation.

In this chapter, we describe the steps that are needed to connect to, configure, and manage
z/OS HyperSwap from Tivoli Storage Productivity Center for Replication 5.2.

This chapter includes the following topics:

򐂰 Overview of z/OS HyperSwap
򐂰 Prerequisites
򐂰 z/OS HyperSwap sessions
򐂰 Description and usage of HyperSwap enabled sessions
򐂰 Use cases

© Copyright IBM Corp. 2014. All rights reserved. 355

7.1 Overview of z/OS HyperSwap
z/OS HyperSwap technology became the industry standard by removing the effect of storage
systems failures for System z customers. The technology is provided in several different
implementation options to meet the various needs of the System z and z/OS customer base.
It extends the Parallel Sysplex® redundancy to storage systems, so whether your
requirements are continuous availability, disaster recovery, or business continuity, z/OS
HyperSwap technology can provide a solution for your environment.

HyperSwap functionality provides planned and unplanned actions in an z/OS environment. By

using Planned HyperSwap actions, the following tasks can be peformed:
򐂰 Transparently switch all primary storage systems disks with the secondary storage
systems disks.
򐂰 Perform storage systems configuration maintenance and planned site maintenance
without requiring any applications to be quiesced.

Unplanned HyperSwap action contains other functions to transparently switch to use auxiliary
storage systems if an unplanned outage of the primary storage systems occurs. Unplanned
HyperSwap action allows production systems to remain active during a storage system
failure. The storage system failures \ no longer constitutes a single point of failure for an entire
Parallel Sysplex.

Tivoli Storage Productivity Center for Replication manages the HyperSwap function with code
in the Input/Output Supervisor (the I/O Supervisor component of z/OS). IBM analyzed all field
storage system failures and created a set of trigger events that are monitored by z/OS
HyperSwap. When one of these HyperSwap trigger events occurs, a “Data Freeze” across all
LSSs on all storage systems is started. All I/O to all devices is queued (Extended Long Busy
state), which maintains full data integrity and cross volumes data consistency. z/OS then
completes the HyperSwap function of recovering the target devices and rebuilding all z/OS
internal control blocks to point to the recovered target devices. When this process is
complete, all I/O is released and all applications continue to run against the recovered target
devices, which transparently manage a complete storage system outage, with a dynamic
“busy” and a redirection of all host I/O. Applications must tolerate the Extended Long Busy
state, which is not apparent to their operation, but elongates I/O that is in progress until the
HyperSwap actions are completed.

As of the Tivoli Storage Productivity Center version 5.2, Tivoli Storage Productivity Center for
Replication that is running on an open system (Windows, AIX, or Linux) or running on z/OS
can manage z/OS HyperSwap, as shown in Figure 7-1 on page 357. By using this Tivoli
Storage Productivity Center for Replication configuration, many HyperSwap sessions can be
managed in different sysplex or monoplex environments. Compared to older versions of Tivoli
Storage Productivity Center for Replication that were running on z/OS in which you can
manage only one HyperSwap session from one Tivoli Storage Productivity Center for
Replication, you can manage HyperSwap sessions in multiple sysplexes and monoplexes
from one Tivoli Storage Productivity Center for Replication server with version 5.2 running on
open systems or z/OS.

356 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 7-1 z/OS HyperSwap

The HyperSwap function can be used in continuous availability, disaster recovery, or business
continuity solutions that are designed with two or three sites and based on synchronous
replication. The following Tivoli Storage Productivity Center for Replication sessions use
HyperSwap functions:
򐂰 Basic HyperSwap
򐂰 Metro Mirror with Failover/Failback
򐂰 Metro Global Mirror
򐂰 Metro Global Mirror with Practice

For more information about these sessions, see 7.3, “z/OS HyperSwap sessions” on
page 360.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 357
7.2 Prerequisites
In this section, the prerequisites for the Basic HyperSwap implementation are described.

7.2.1 Hardware
Tivoli Storage Productivity Center for Replication and HyperSwap sessions require IBM
Storage Systems DS8000, DS6000, or ESS800 with advanced copy function Metro Mirror.
Metro Mirror replication must be established before HyperSwap can be enabled.

7.2.2 Software
The Basic HyperSwap function is supported by z/OS version 1.12 and later and requires two
HyperSwap address spaces that must be running in z/OS.

Note: To use IP Management of HyperSwap, you need z/OS Version 1 Release 13 or z/OS
Version 2 Release 1 with APAR OA40866. The IP Management of HyperSwap is required
for open systems.

The following HyperSwap address spaces must be running:

򐂰 HyperSwap Management address space
򐂰 HyperSwap API address space

You can start both of these address spaces by adding simple procedures to SYS1.PROCLIB,
and then the START procmemname command is run manually, or by including the command in
the COMMNDxx member of your SYS1.PARMLIB. The examples of the PROCLIB members and
HyperSwap Management and HyperSwap API address space are shown in Example 7-1 and
Example 7-2.

Example 7-1 HyperSwap Management started task JCL

//HSIB PROC PORT=5858
//STEP EXEC PGM=IOSHMCTL,TIME=NOLIMIT,REGION=0M,
// PARM='SOCKPORT=&PORT'
//SYSPRINT DD SYSOUT=A

Example 7-2 HyperSwap API started task JCL

//HSIBAPI JOB MSGLEVEL=(1,1),TIME=NOLIMIT,REGION=0M
// EXEC PGM=IOSHSAPI

7.2.3 Connectivity
Participating hosts in HyperSwap sessions must have FICON connections to both storage
systems in a Metro Mirror relationship. This means that primary and secondary devices must
be defined in the IODF and have operational paths to all devices. It is also suggested that
both storage systems be defined with the same number of paths and the same number of
Parallel Access Volume (PAV) aliases. After the HyperSwap is done, all host read and write
operations are sent to auxiliary storage system.

358 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: You also can have multiple source or multiple target systems for the HyperSwap.
There is no restriction of having only a single source or target box.

7.2.4 Enabling a host name or IP address connection to a z/OS host system

To connect z/OS host systems in Tivoli Storage Productivity Center for Replication that is
running on Windows, Linux, AIX, or z/OS, you can use a z/OS host name or IP address. By
adding a z/OS host to Tivoli Storage Productivity Center for Replication, you can fully manage
HyperSwap sessions that are running on that z/OS host system. This feature enables a single
instance of Tivoli Storage Productivity Center for Replication to manage multiple HyperSwap
sessions that are running in different z/OS systems and sysplexes. For more information
about adding the hosts, see section 7.4.1, “Setting up a HyperSwap enabled session” on
page 369.

7.2.5 Enabling z/OS HyperSwap and adding a Tivoli Storage Productivity

Center for Replication user to z/OS host
Complete the following steps on z/OS host to enable z/OS HyperSwap. These steps set the
required Resource Access Control Facility (RACF) settings on the host system and define the
SOCKPORT parameter when the HyperSwap management address space IOSHMCTL is
started:
1. Use an OMVS segment to define the name BHIHSRV as a user, as shown in the following
example command, where user_identifier is a number that represents the user:
ADDUSER BHIHSRV OMVS(UID(user_identifier) SHARED HOME(‘/’)) NOPASSWORD

Note: If your installation uses the STARTED class or the started procedures table
(ICHRIN03) of the z/OS Security Server, ensure that the user BHIHSRV is associated
with the started task BHIHSRV. For more information about the use of the STARTED
class or the started procedures table, see Security Server RACF Security
Administrator's Guide, SA22-7683-15, which is available at this website:

http://www-01.ibm.com/support/docview.wss?uid=pub1sa22768315

2. If the ANT.REPLICATIONMANAGER entity is not defined to the FACILITY class, run the
following command:
RDEFINE FACILITY ANT.REPLICATIONMANAGER UACC(NONE)
3. Authorize the name BHIHSRV to the ANT.REPLICATIONMANAGER entity in the
FACILITY class by running the following command:
PERMIT ANT.REPLICATIONMANAGER CLASS(FACILITY) ID(BHIHSRV) ACCESS(CONTROL)
4. To define the user ID and password that are used for authentication from Tivoli Storage
Productivity Center for Replication to the z/OS host system, run the following commands:
ADDUSER userid PASSWORD(password)
PERMIT ANT.REPLICATIONMANAGER CLASS(FACILITY) ID(userid) ACCESS(CONTROL)
You must enter this user ID and password when you add the z/OS host system to Tivoli
Storage Productivity Center for Replication.
5. To activate the changes in the previous steps, run the following command:
SETROPTS RACLIST(FACILITY) REFRESH

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 359
 6. Start the IOSHMCTL address space with the SOCKPORT parameter, as shown in the
following example:

//HSIB JOB MSGLEVEL=(1,1),TIME=NOLIMIT,REGION=0M

//IEFPROC EXEC PGM=IOSHMCTL,PARM=’SOCKPORT=port_number’

The port_number is 1 - 65535. You must enter this port number when you add a z/OS host
system to Tivoli Storage Productivity Center for Replication, as described in 7.4.1, “Setting up
a HyperSwap enabled session” on page 369.

7.3 z/OS HyperSwap sessions

The following Tivoli Storage Productivity Center for Replication sessions use HyperSwap
functions:
򐂰 Basic HyperSwap
򐂰 Metro Mirror Failover/Failback
򐂰 Metro Global Mirror
򐂰 Metro Global Mirror with Practice

These sessions are described next.

7.3.1 Basic HyperSwap sessions

Basic HyperSwap is a Copy Services solution that provides continuous availability of data if a
storage system failure occurs. It uses z/OS HyperSwap functionality to extend Parallel
Sysplex availability to include management across planned and unplanned events. It also
masks storage system failures through a switch to the Metro Mirror target devices. This
solution works on the same data center floor, and can be extended across two local sites or
three site configurations with Metro Global Mirror architecture. The scope of the HyperSwap
functionality that is provided is only z/OS.

With the Basic HyperSwap session type, Tivoli Storage Productivity Center for Replication
offers only single site HyperSwap functionality and is not intended for two site HyperSwap
functionality. Planned or unplanned Metro Mirror suspend capabilities are not available for
Basic HyperSwap sessions, even though these functions are performed as part of the
HyperSwap process. The Basic HyperSwap session type does not ensure any data
consistency on auxiliary storage systems in case of mirroring failures. For this reason, Basic
HyperSwap can be considered a Continuous Availability feature without disaster recovery
capabilities.

Basic HyperSwap replication performs the following tasks:

򐂰 Manages count key data (CKD) volumes in Metro Mirror to manage synchronous copy
relationships only. The graphical user interface (GUI) shows only CKD volumes when you
add a copy set. The command-line interface (CLI) does not add a copy set if a fixed block
volume is specified.
򐂰 Monitors events that indicate a storage device failed.
򐂰 Determines whether the failing storage device is part of a Metro Mirror synchronous pair.
򐂰 Determines the action to be taken from policy.

360 Tivoli Storage Productivity Center for Replication for Open Systems
 򐂰 Ensures that data remains consistent during the HyperSwap process.
򐂰 Swaps the I/O between the primary logical devices in the consistency group with the
secondary logical devices in the consistency group. A swap can occur from the preferred
logical devices to the alternative logical devices or from the alternative logical devices to
the preferred logical devices.

Figure 7-2 shows the Basic HyperSwap session in Tivoli Storage Productivity Center for
Replication.

Figure 7-2 Basic HyperSwap session

7.3.2 HyperSwap enabled Metro Mirror Failover/Failback sessions

Metro Mirror Failover/Failback with the HyperSwap function enabled combines the continuous
availability of Basic HyperSwap with the redundancy of a two-site Metro Mirror
Failover/Failback solution when CKD volumes are managed on the z/OS host. If the primary
volumes encounter a permanent I/O error, the I/O is automatically swapped to the secondary
site with minimal effect on the application. Tivoli Storage Productivity Center for Replication in
Metro Mirror Failover/Failback with HyperSwap session provides a data freeze if the link
failure and other conditions occurred. With this solution, Tivoli Storage Productivity Center for
Replication provides a disaster recovery capability and the HyperSwap function. As a result,
all data on all storage systems at the remote site is data consistent to the Point in Time of the
failure.

A HyperSwap function can provide planned or unplanned actions. A planned action is used
when you must perform some storage system maintenance on a primary storage or some
primary site management, for example. Swap occurs when you run a HyperSwap command
from the GUI, CLI, or the SETHS SWAP z/OS system command. For more information about this
command, see z/OS V1R13.0 MVS™ System Commands, SA22-7627-28.

The Unplanned HyperSwap feature provides other functions to transparently switch to use
auxiliary storage systems in the event of unplanned outages of the primary storage systems.
Unplanned HyperSwap action allows production systems to remain active during a storage
system failure. Storage system failures no longer constitute a single point of failure.

Figure 7-3 shows you Metro Mirror Failover/Failback session with HyperSwap enabled in
Tivoli Storage Productivity Center for Replication.

Figure 7-3 Metro Mirror Failover/Failback session

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 361
 Figure 7-4 shows the state transition diagram for a Metro Mirror Failover/Failback session that
shows the effect of the HyperSwap actions.

Figure 7-4 HyperSwap enabled Metro Mirror FO/FB transition diagram

7.3.3 HyperSwap enabled Metro Global Mirror sessions

In a Metro Global Mirror session with HyperSwap enabled, a failure on the primary storage
system causes an automatic HyperSwap operation, which transparently redirects application
I/O to the auxiliary (intermediate) storage system. The Global Mirror relationship in the
session continues to run uninterrupted throughout this process. With this configuration, you
can achieve almost a zero data loss at larger distances.

By using synchronous mirroring, you can switch from the primary site to the intermediate site
during a planned or unplanned outage as in the Metro Mirror Failover/Failback session. It also
provides continuous disaster recovery protection of the intermediate and remote site if a
switch from primary site occurs. With this configuration, you can reestablish direction from
H2 (intermediate) → H1 (local) → H3 (remote) recover ability while production continues to
run at site H2. This setup also can reduce the workload on-site H1.

362 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 7-5 shows Metro Global Mirror with HyperSwap session in Tivoli Storage Productivity
Center for Replication.

Figure 7-5 Metro Global Mirror session

Figure 7-6 on page 364 and Figure 7-7 on page 365 show the state transition diagrams for a
Metro Global Mirror session that shows the effect of the HyperSwap actions.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 363
 From Host on From Host
Intermediate Site Remote Site
Transition Transition
Diagram Diagram
Inactive
session

Host on Host on
Local Local
site site

StartH1H3
StartH1H2H3
StartH1H2H3 StartH1H2H3

StartH1H3 StartH1H2H3

SuspH2H3

StartH1H3 Suspend
Suspend
StartH1H2H3 Host on
StartH1H3 Suspend Local
site
StartH1H3

Enable Copy
RecoverH3 To Site 2
HyperSwap
Recover RecoverH2

RecoverH3
StartH1H2

RecoverH1

StartH1H2
Suspend
StartH1H2
Enable Copy Enable Copy StartH2H1
StartH1H2
To Site 1 To Site 1
StartH2H1 Suspend

Host on Host on
Remote Intermediate RecoverH2
site site

StartH2H1

Go to Host on Go to Host on
Remote Site Intermediate Site Host on
Enable Copy
Transition Transition intermediate
To Site 1
Diagram Diagram site

Figure 7-6 Host that is running on a local site

364 Tivoli Storage Productivity Center for Replication for Open Systems
 From Host on
Local Site
Transition
Diagram

Host on
StartH2H3 Intermediate
site

StartH2H1H3

StartH2H1H3 StartH2H1H3

StartH2H3 StartH2H1H3

SuspH1H3

StartH2H3 Suspend
Suspend
StartH2H1H3 Host on
StartH2H3 Suspend Intermediate
site
StartH2H3

Enable Copy
RecoverH3 To Site 1
HyperSwap
Recover RecoverH1

RecoverH3
StartH2H1

RecoverH2

StartH2H1
Suspend
StartH2H1
Enable Copy Enable Copy StartH1H2
StartH2H1
To Site 1 To Site 2
StartH1H2 Suspend

Host on Host on
Remote Local RecoverH1
site site

StartH1H2

Go to Host on Go to Host on
Remote Site Local Site Host on
Enable Copy
Transition Transition Local
To Site 2
Diagram Diagram site

Figure 7-7 Host that is running on an intermediate site

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 365
7.3.4 HyperSwap enabled Metro Global Mirror with Practice sessions
In a Metro Global Mirror session with Practice and HyperSwap enabled, a failure on the
primary storage system causes an automatic HyperSwap operation as in the Metro Global
Mirror session with HyperSwap enabled. The difference for the Metro Global Mirror session
with HyperSwap is that this session uses practice volumes for disaster recovery practice.

Figure 7-8 shows you the Metro Global Mirror with Practice and HyperSwap session.

Figure 7-8 Metro Global Mirror with Practice session

Figure 7-9 on page 367 and Figure 7-10 on page 368 show the state transition diagrams for a
Metro Global Mirror session that shows the effect of the HyperSwap actions.

366 Tivoli Storage Productivity Center for Replication for Open Systems
 From Host on From Host
Intermediate Site Remote Site
Transition Transition
Inactive
Diagram Diagram
session

Host on Host on
Local Local
site site

StartH1H3
StartH1H2H3

Flash StartH1H2H3 StartH1H2H3

StartH1H3 SuspH2H3
StartH1H2H3
Flash

Suspend StartH1H3 Suspend

Suspend

StartH1H2H3

StartH1H3
StartH1H3 RecoverH3
HyperSwap

RecoverH2 Flash
Recover

Enable Copy
Flash To Site 1

Enable Copy Enable Copy

To Site 1 To Site 1 Host on
Remote
site
Host on Host on
Remote Intermediate
site site

Go to Host on
Remote Site
Transition
Go to Host on Go to Host on Diagram
Remote Site Intermediate Site
Transition Transition
Diagram Diagram

Figure 7-9 Host that is running on a local site

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 367
 From Host on
Local Site
Transition
Diagram

Host on
StartH2H3 Intermediate
site

StartH2H1H3

Flash StartH2H1H3 StartH2H1H3

StartH2H3 SuspH1H3
StartH2H1H3
Flash

Suspend Flash
Suspend StartH2H3 Suspend

StartH1H1H3

StartH2H3

StartH2H3 RecoverH3
HyperSwap

RecoverH1 Flash
Recover

Enable Copy
To Site 1
Flash

Enable Copy Enable Copy

To Site 1 To Site 2 Host on
Remote
site
Host on Host on
Remote Local
site site

Go to Host on
Remote Site
Transition
Go to Host on Go to Host on Diagram
Remote Site Local Site
Transition Transition
Diagram Diagram

Figure 7-10 Host that is running on an intermediate site

368 Tivoli Storage Productivity Center for Replication for Open Systems
7.3.5 Hardened Freeze
The z/OS HyperSwap facilities also provide an optional Hardened Freeze capability for Metro
Mirror Single Direction, Metro Mirror Failover/Failback, Metro Mirror Failover/Failback with
Practice, Metro Global Mirror, and Metro Global Mirror with Practice session types. This
function enables the z/OS HyperSwap subcomponent of I/O Supervisor to directly manage
the suspension events (planned and unplanned) without requiring any intervention with Tivoli
Storage Productivity Center for Replication. This feature greatly enhances the management
of planned and unplanned suspension events, as described in the following sample
scenarios:
򐂰 A disabled Metro Mirror session that is not HyperSwap enabled is managed by Tivoli
Storage Productivity Center for Replication that is running on z/OS and a planned or
unplanned suspend occurs. In this scenario, if the Hardened Freeze option is not selected,
the suspend operation is performed by Tivoli Storage Productivity Center for Replication.
Because Tivoli Storage Productivity Center for Replication is on the same disks that are
part of the Metro Mirror session and, therefore, subject to freeze, this can lead the Tivoli
Storage Productivity Center for Replication to freeze, which prevents the successful
completion of the suspend operations. Having the Hardened Freeze enabled, the suspend
operation is performed by I/O Supervisor, which does not require access to disks to
complete the freeze operations.
򐂰 A disabled Metro Mirror session that is managing z/OS storage that is not HyperSwap
enabled is managed by Tivoli Storage Productivity Center for Replication that is running on
Open Systems. Consider a situation in which an extended outage in the network
infrastructure prevents Tivoli Storage Productivity Center for Replication from
communicating with the storage systems. In this scenario, without Hardened Freeze
enabled, an unplanned suspension event does not trigger a freeze, which leaves the
auxiliary storage systems inconsistent (and affects primary storage systems). With the
Hardened Freeze option enabled, the suspend operation is performed by I/O Supervisor,
which does not require network connectivity to complete the freeze operations.

The Hardened Freeze is an inherent capability of HyperSwap enabled session types.

7.4 Description and usage of HyperSwap enabled sessions

In this section, we describe how to set up HyperSwap enabled sessions and how they can be
managed through the Tivoli Storage Productivity Center for Replication GUI. Several
unplanned scenarios also are described.

7.4.1 Setting up a HyperSwap enabled session

To enable the HyperSwap functions for a Tivoli Storage Productivity Center for Replication
session, you must first set up the z/OS components, starting with the address spaces, as
described in “Software” on page 358.

After the z/OS address spaces are running, the communication between Tivoli Storage
Productivity Center for Replication and z/OS can be established. From the Health Overview
window, open the Host Systems panel through one of the available links, as shown in
Figure 7-11 on page 370.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 369
Figure 7-11 Health Overview window

From the Host System panel, click Add Host Connection, as shown in Figure 7-12.

Figure 7-12 Add Host System

The Add Host Connection panel opens, as shown in Figure 7-13. Select the z/OS connection
type and provide the following required information:
򐂰 IP address or Host Name of one or more of the z/OS systems forming the sysplex.

Note: We advise that you define connections to two or more members (systems or
hosts, for example) in the sysplex for redundancy.

370 Tivoli Storage Productivity Center for Replication for Open Systems
 򐂰 Port that is used to communicate with HyperSwap address space. This port must be the
same as specified in the HyperSwap Management address space definition. The default is
5858.
򐂰 User name and password for Tivoli Storage Productivity Center for Replication that are
defined in z/OS as described in “Enabling z/OS HyperSwap and adding a Tivoli Storage
Productivity Center for Replication user to z/OS host” on page 359 and shown in
Figure 7-13.

Figure 7-13 Add Host Connection panel

Click Add Host and wait for the connection to be established. When the connection is
established, the Host Systems panel shows the host as Connected, as shown Figure 7-14.

Figure 7-14 Host System panel that shows the host is connected

Now we are ready to create the session. The process of creating a HyperSwap enabled
session is the same as any other DS8000 session (see 4.3, “Managing DS8000 sessions” on
page 201). When at least one Host System is defined, the HyperSwap options are made
available for the HyperSwap capable session types.

To enable the HyperSwap for a session, select the Manage H1-H2 with HyperSwap option in
the Session Properties panel and then select the system (or Sysplex) from the drop-down
menu, as shown in Figure 7-15 on page 372.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 371
 Figure 7-15 Sysplex selection in the Session Properties panel

Click Next and complete the session creation process. By opening the Session Details panel
(see Figure 7-16), we can see that an association with a z/OS system is shown, which means
that the session is HyperSwap enabled.

Figure 7-16 Session Details panel that shows the z/OS association

372 Tivoli Storage Productivity Center for Replication for Open Systems
 The z/OS components still show that there is no active configuration to manage, as shown in
Figure 7-17.

D HS,CONFIG
IOSHM0304I Active Configurations
No configuration data

D HS,STATUS
IOSHM0303I HyperSwap Status
Replication Session: N/A
Socket Port: 5858
HyperSwap disabled:
No configuration data
SYSTEM1:
No configuration data
Figure 7-17 z/OS displays

Select Start H1 → H2 from the Select Action drop-down menu and click Go to start the
session. During the session starting process, Tivoli Storage Productivity Center for
Replication performs the following tasks, which are also reported in the console log (see
Figure 7-18.):
򐂰 Establishes the mirroring relationships (in this example, there is only a Metro Mirror) and
waits until all of the replication is in consistent state
򐂰 Loads the mirroring configuration to the HyperSwap address space

Figure 7-18 Tivoli Storage Productivity Center for Replication console log

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 373
 After the session configuration is successfully loaded to z/OS, the HyperSwap management
is now performed by the z/OS IOS component (which is in the Syslog), as shown in
Figure 7-19.

16.54.50 STC00054 IOSHM0201I HyperSwap Configuration LoadTest fails 584

584 Reason: Configuration Validation fails on member SYSTEM1
584 Reason Code: 40. Devices: 00F43-00F83
16.54.52 STC00054 IOSHM0201I HyperSwap Configuration LoadTest fails 585
585 Reason: Configuration Validation fails on member SYSTEM1
585 Reason Code: 50. Devices: 00F83-00F43
16.55.21 STC00054 IOSHM0501I Response from API for FC = 0, RC = 4, Rsn = 0
16.55.21 STC00054 IOSHM0501I Response from API for FC = 1, RC = 0, Rsn = 3
16.55.21 STC00054 IOSHM0200I HyperSwap Configuration Load complete
16.55.21 STC00054 *IOSHM0803E HyperSwap enabled with limited capability
16.55.21 STC00054 IOSHM0805I HyperSwap Enabled
16.55.21 STC00054 IOSHM0501I Response from API for FC = 0, RC = 0, Rsn = 0
16.55.21 STC00054 IOSHM0501I Response from API for FC = 19, RC = 0, Rsn = 2
16.55.21 STC00054 IOSHM0501I Response from API for FC = 13, RC = 0, Rsn = 0
16.55.21 STC00054 IOSHM0808I HyperSwap Configuration Monitoring started, time
interval = 5 minutes
16.55.21 STC00054 IOSHM0501I Response from API for FC = 15, RC = 0, Rsn = 0
16.55.25 STC00054 IOSHM0305I HyperSwap allowed by operator
16.55.25 STC00054 IOSHM0300I HyperSwap function enabled for all PPRC pairs
Figure 7-19 HyperSwap address space that shows the configuration loading

Note: The IOSHM0201I LOADTEST fails messages (as shown in Figure 7-19) are typical
and used by Tivoli Storage Productivity Center for Replication to assure that they identify
which of the storage systems is the primary.

Querying the z/OS components, an active configuration is now shown, as shown in

Figure 7-20 on page 375.

374 Tivoli Storage Productivity Center for Replication for Open Systems
 D HS,CONFIG
IOSHM0304I Active Configurations
Replication Session Name Replication Session Type
ITSO-MM-HS HyperSwap

D HS,CONFIG(DETAIL)
IOSHM0304I HyperSwap Configuration
Replication Session: ITSO-MM-HS
Prim. SSID UA DEV# VOLSER Sec. SSID UA DEV# Status
06 03 00F43 8K1103 06 03 00F83

D HS,STATUS
IOSHM0303I HyperSwap Status
Replication Session: ITSO-MM-HS
Socket Port: 5858
HyperSwap enabled
New member configuration load failed: Disable
Planned swap recovery: Disable
Unplanned swap recovery: Disable
FreezeAll: Yes
Stop: No
Figure 7-20 z/OS display that shows the configuration status

Finally, the Tivoli Storage Productivity Center for Replication shows the session in HyperSwap
enabled status by showing a green H in the drawing that represents the session, as shown in
Figure 7-21.

Figure 7-21 Session Details panel that shows the HyperSwap enabled status

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 375
 Now that the configuration is loaded in the z/OS address space, we can perform a
HyperSwap test. The volume 8K1103 is online with the device number 0F43, as shown in
Figure 7-22.

D U,VOL=8K1103
RESPONSE=SYSTEM1
IEE457I 17.14.51 UNIT STATUS 220
UNIT TYPE STATUS VOLSER VOLSTATE
0F43 3390 O 8K1103 PRIV/RSDNT
Figure 7-22 z/OS display that shows the device number for volume 8K1103

From the Session Detail panel, select HyperSwap from the Select Action drop-down menu
(as shown in Figure 7-23) and click Go.

Figure 7-23 Session Details panel that shows the HyperSwap action

Click Yes in the confirmation panel, as shown in Figure 7-24.

Figure 7-24 Confirmation panel

376 Tivoli Storage Productivity Center for Replication for Open Systems
 The HyperSwap process starts and the z/OS system log reports the actions that are
performed by HyperSwap address space, as shown Figure 7-25.

17.18.41 STC00054 IOSHM0400I 17:18:41.68 HyperSwap requested

17.18.41 STC00054 IOSHM0424I Master status = 00000000 00000000 0000000F00000000
17.18.41 STC00054 IOSHM0401I 17:18:41.68 Planned HyperSwap started - UserExit
17.18.41 STC00054 IOSHM0424I Master status = 00000000 00000000 0000000F01000000
17.18.41 STC00054 IOSHM0417I 0:00:00.00 Response from SYSTEM1, API RC = 0, Rsn = 2
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F01000000
17.18.41 STC00054 IOSHM0402I 17:18:41.69 HyperSwap phase - Validation of I/O connectivity starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 14, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.70 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F02000000
17.18.41 STC00054 IOSHM0403I 17:18:41.70 HyperSwap phase - Validation of I/O connectivity completed
17.18.41 STC00054 IOSHM0404I 17:18:41.70 HyperSwap phase - Freeze and quiesce DASD I/O starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 17, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.71 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F03000000
17.18.41 STC00054 IOSHM0405I 17:18:41.71 HyperSwap phase - Freeze and quiesce DASD I/O completed
17.18.41 STC00054 IOSHM0406I 17:18:41.71 HyperSwap phase - Failover PPRC volumes starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 10, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.72 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F04000000
17.18.41 STC00054 IOSHM0407I 17:18:41.72 HyperSwap phase - Failover PPRC volumes completed
17.18.41 STC00054 IOSHM0408I 17:18:41.72 HyperSwap phase - Swap UCBs starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 3, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.73 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F05000000
17.18.41 STC00054 IOSHM0409I 17:18:41.73 HyperSwap phase - Swap UCBs completed
17.18.41 STC00054 IOSHM0410I 17:18:41.73 HyperSwap phase - Resume DASD I/O starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 6, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.84 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F06000000
17.18.41 STC00054 IOSHM0411I 17:18:41.84 HyperSwap phase - Resume DASD I/O completed
17.18.41 STC00054 IOSHM0501I Response from API for FC = 18, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0429I 17:18:41.84 HyperSwap processing issued an UnFreeze
17.18.41 STC00054 IOSHM0412I 17:18:41.84 HyperSwap phase - Cleanup starting
17.18.41 STC00054 IOSHM0501I Response from API for FC = 12, RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0417I 17:18:41.85 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 00000000 80000000 0000000F08000000
17.18.41 STC00054 IOSHM0413I 17:18:41.85 HyperSwap phase - Cleanup completed
17.18.41 STC00054 *IOSHM0803E HyperSwap Disabled
17.18.41 STC00054 IOSHM0809I HyperSwap Configuration Monitoring stopped
17.18.41 STC00054 IOSHM0501I Response from API for FC = 0, RC = 4, Rsn = 0
17.18.41 STC00054 IOSHM0417I 0:00:00.00 Response from SYSTEM1, API RC = 0, Rsn = 0
17.18.41 STC00054 IOSHM0424I Master status = 20000000 00000000 0000000F09000000
17.18.41 STC00054 IOSHM0414I 17:18:41.86 Planned HyperSwap completed
17.18.41 STC00054 IOSHM0200I HyperSwap Configuration Purge complete
17.18.41 STC00054 IOSHM0424I Master status = 20000000 00000000 0000001000000000

Figure 7-25 z/OS system log showing the ongoing HyperSwap

Note: Message “IOSHM0429I 17:18:41.84 HyperSwap processing issued an UnFreeze” (as shown in Figure 7-25)
indicates that the HyperSwap is complete now. After Resume and UnFreeze are complete, I/Os resumes
processing. Cleanup is not necessary for the applications and system to resume running and is purposely
designed to avoid the use of CPU resources (which potentially take a long time) so that the customer's
applications can continue.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 377
 Also, the Tivoli Storage Productivity Center for Replication console log shows the HyperSwap
replication messages, as shown in Figure 7-26.

Figure 7-26 Console log that shows the HyperSwap messages

Checking the volume 8K1103, we can see that the volume is now online with device number
0F83 (see Figure 7-27), which proves that the HyperSwap occurred.

RESPONSE=SYSTEM1
IEE457I 17.19.50 UNIT STATUS 220
UNIT TYPE STATUS VOLSER VOLSTATE
0F83 3390 O 8K1103 PRIV/RSDNT
Figure 7-27 z/OS display that shows the device number for volume 8K1103

The session now shows Normal status and Target Available state, as shown in Figure 7-28.

Figure 7-28 Session Details panel that shows the session status after the HyperSwap

378 Tivoli Storage Productivity Center for Replication for Open Systems
 Following the HyperSwap, the configuration was purged and the HyperSwap disabled, as
shown in Figure 7-29.

D HS,STATUS

17.20.16 STC00054 IOSHM0303I HyperSwap Status 672 672

672 Replication Session: N/A
672 Socket Port: 5858
672 HyperSwap disabled:
672 No configuration data
672 SYSTEM1:
672 No configuration data
Figure 7-29 z/OS displays that shows there is no configuration loaded

To return to the original configuration, we first must restore the Metro Mirror. Select the Start
H2 → H1 action and wait for the session to go into Normal status. The new configuration is
then loaded to the HyperSwap address space, as shown is Figure 7-30.

D HS,CONFIG(DETAIL)

17.47.11 STC00054 IOSHM0304I HyperSwap Configuration 607 607

607 Replication Session: ITSO-MM-HS
607 Prim. SSID UA DEV# VOLSER Sec. SSID UA DEV£ Status
607 06 03 00F83 8K1103 06 03 00F43

Figure 7-30 z/OS displays that shows a new configuration is loaded

To perform the final HyperSwap, we simulate an outage on primary storage system by

running the VARY 0F83,OFFLINE,FORCE command. This action triggers an unplanned
HyperSwap, as shown in Figure 7-31 on page 380.

Note: Running this command is called boxing the device. You can “unbox” the device by
running a VARY 0F83,ONLINE,UNCOND command on the old primary. The device does not
come online because of duplicate volume serial (volser) numbers; however, this should be
sufficient to unbox the device.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 379
 17.50.46 STC00054 IOSHM0400I 17:50:46.62 HyperSwap requested
17.50.46 STC00054 IOSHM0424I Master status = 00000000 00000000 0000001000000000
17.50.46 STC00054 IOSHM0401I 17:50:46.62 Unplanned HyperSwap started - ENF
17.50.46 STC00054 IOSHM0424I Master status = 00000000 00000000 0000001001000100
17.50.46 STC00054 IOSHM0417I 0:00:00.00 Response from SYSTEM1, API RC = 0, Rsn = 2
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001001000100
17.50.46 STC00054 IOSHM0402I 17:50:46.64 HyperSwap phase - Validation of I/O connectivity starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 14, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0417I 17:50:46.65 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001002000100
17.50.46 STC00054 IOSHM0403I 17:50:46.65 HyperSwap phase - Validation of I/O connectivity completed
17.50.46 STC00054 IOSHM0404I 17:50:46.65 HyperSwap phase - Freeze and quiesce DASD I/O starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 17, RC = 0, Rsn = 8
17.50.46 STC00054 IOSHM0417I 17:50:46.66 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001003000100
17.50.46 STC00054 IOSHM0405I 17:50:46.66 HyperSwap phase - Freeze and quiesce DASD I/O completed
17.50.46 STC00054 IOSHM0501I Response from API for FC = 96, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0501I Response from API for FC = 97, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0406I 17:50:46.66 HyperSwap phase - Failover PPRC volumes starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 10, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0417I 17:50:46.67 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001004000100
17.50.46 STC00054 IOSHM0407I 17:50:46.67 HyperSwap phase - Failover PPRC volumes completed
17.50.46 STC00054 IOSHM0408I 17:50:46.67 HyperSwap phase - Swap UCBs starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 3, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0417I 17:50:46.68 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001005000100
17.50.46 STC00054 IOSHM0409I 17:50:46.68 HyperSwap phase - Swap UCBs completed
17.50.46 STC00054 IOSHM0410I 17:50:46.68 HyperSwap phase - Resume DASD I/O starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 6, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0417I 17:50:46.79 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001006000100
17.50.46 STC00054 IOSHM0411I 17:50:46.79 HyperSwap phase - Resume DASD I/O completed
17.50.46 STC00054 IOSHM0501I Response from API for FC = 18, RC = 0, Rsn = 8
17.50.46 STC00054 IOSHM0429I 17:50:46.79 HyperSwap processing issued an UnFreeze
17.50.46 STC00054 IOSHM0412I 17:50:46.79 HyperSwap phase - Cleanup starting
17.50.46 STC00054 IOSHM0501I Response from API for FC = 12, RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0417I 17:50:46.80 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 00000000 80000000 0000001008000100
17.50.46 STC00054 IOSHM0413I 17:50:46.80 HyperSwap phase - Cleanup completed
17.50.46 STC00054 *IOSHM0803E HyperSwap Disabled
17.50.46 STC00054 IOSHM0809I HyperSwap Configuration Monitoring stopped
17.50.46 STC00054 IOSHM0501I Response from API for FC = 0, RC = 4, Rsn = 0
17.50.46 STC00054 IOSHM0417I 0:00:00.00 Response from SYSTEM1, API RC = 0, Rsn = 0
17.50.46 STC00054 IOSHM0424I Master status = 20000000 00000000 0000001009000100
17.50.46 STC00054 IOSHM0414I 17:50:46.80 Unplanned HyperSwap completed
17.50.46 STC00054 IOSHM0200I HyperSwap Configuration Purge complete
17.50.46 STC00054 IOSHM0424I Master status = 20000000 00000000 0000001100000100
17.50.50 STC00054 IOSHM0200I HyperSwap Configuration LoadTest complete

Figure 7-31 Unplanned HyperSwap related messages in the z/OS system log

380 Tivoli Storage Productivity Center for Replication for Open Systems
7.5 Use cases
Most z/OS customers require continuous availability and disaster recovery to protect their
business applications. To address the high availability requirements of business applications,
many z/OS customers implemented Parallel Sysplex. However, high availability also must be
extended to storage systems. Storage systems today manage more data and, therefore, the
effect of a storage system outage is more widespread, often affecting a Parallel Sysplex and
potentially causing a Parallel Sysplex wide outage.

To address these outages, the HyperSwap technology helps mask storage system failures
with an Extended Long Busy function (ELB) to the application I/O followed by a redirection of
that I/O to a recovered secondary device. By using this technology, there is no effect on
business applications when a storage system planned or unplanned outage occurs.

In this section, two high availability and Disaster Recovery scenarios and the possible
solutions that are based on HyperSwap technology are described.

Scenario 1: Active-Active campus configuration

An Active-Active campus is a high availability solution that often is based on advanced
clustering and data replication technologies. This kind of solution provides continuous
availability features, which implement hardware redundancy in multiple locations and
sophisticated software facilities that allow workload switching among the sites. Also, data
replication plays an important role in this kind of solution, which provides a consistent copy of
data across the campus.

In a typical Active-Active campus configuration, the application workload is running in two

separate sites that are interconnected through LAN and SAN extensions. Consistent copies
of the data are continuously present in both sites. This solution can manage (transparently to
the users) various critical situations, such as single or multiple hardware failures or even an
entire site failure. In terms of business continuity, the Active-Active campus configuration
cannot be considered a Disaster Recovery solution because, the connection latency
overhead often requires a relatively short distance between the campus sites that do not
survive in the case of major natural disasters.

Figure 7-32 on page 382 shows a schematic representation of an Active-Active campus

configuration that is based on System z and DS8000 technologies.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 381
 Figure 7-32 Active-Active campus configuration

In this scenario, the application workload is running in Site A and Site B. The Parallel Sysplex
facility manages the availability of the application across the sites while the data is replicated
by using synchronous mirroring technologies, such as DS8000 Metro Mirror. To manage the
data replication and the data availability, a Tivoli Storage Productivity Center for Replication
for an Open systems solution can be implemented.

Figure 7-33 on page 383 shows a possible implementation of Tivoli Storage Productivity
Center for Replication for Open systems to manage the data availability for this scenario. In
this solution, an Active-Standby Tivoli Storage Productivity Center for Replication
configuration is deployed across the two sites, with the active server running on the primary
storage site (Site A). An IP connection is provided to manage the storage systems and to
communicate with the z/OS HyperSwap address spaces. A Metro Mirror Failover/Failback
session with HyperSwap enabled is defined to Tivoli Storage Productivity Center for
Replication to manage this kind of configuration. With the Parallel Sysplex facilities, this Tivoli
Storage Productivity Center for Replication implementation provides high availability features
that cover many failure scenarios.

Note: A Parallel Sysplex is not required to use z/OS HyperSwap. A customer can also use
z/OS HyperSwap with a non-parallel sysplex. For example, a sysplex without a Coupling
Facility (CF) or with a system that is running in XCF-local mode.

382 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 7-33 Open systems implementation for an Active-Active campus configuration

Note: For more information about Tivoli Storage Productivity Center for Replication
HyperSwap on z/OS, see IBM Tivoli Storage Productivity Center for Replication for
Series z, SG24-7563, which is available at this website:

http://www.redbooks.ibm.com/redpieces/abstracts/sg247563.html?Open

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 383
 Figure 7-34 shows a primary storage systems failure in Site A.

users

SITE A SITE B

..00101010.. ..00101010..
...10010100.. ...10010100..
....11101010.. ....11101010..
.....00110101.. .....00110101..

HyperSwap

Production Campus

Figure 7-34 Primary storage systems failure in an Active-Active campus configuration

In this case, the failure of primary storage system triggers a HyperSwap that allows
application transparent switching to the auxiliary storage systems.

384 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure 7-35 shows a complete Site A failure.

users

SITE A SITE B

..0010101
..00101010..
. 010.
010..
0. ..00101010..
.. .100101
10010100
00.
0..
...10010100.. ...10010100..
....11101010..
....11
.. 101010... ....11101010..
.....00110101..
......0
. 01101011..
. .....00110101..

HyperSwap

Production Campus

Figure 7-35 Entire primary site failure in an Active-Active campus configuration

The HyperSwap capabilities of Tivoli Storage Productivity Center for Replication enable the
applications that are running on Site B to survive the Site A failure by switching to the Site B
storage systems. In addition, the Parallel Sysplex facilities allow an application that is
switching from Site A to Site B with minimal or no downtime.

Scenario 2: Three-site configuration

A three-site configuration combines the high availability features of an Active-Active campus
configuration with Disaster Recovery capabilities. In addition to the infrastructure that is
required for the campus solution, a remote third site is provided with computing capabilities
and storage capacity for Disaster Recovery purposes. To make this solution effective in terms
of Recovery Time Objective (RTO) and Recovery Point Objective (RPO), more data
replication capabilities must be provided to ensure data availability at the remote site.

Furthermore, to be considered effective in terms of Disaster Recovery, a three-site solution

must have sufficient distance between the campus sites and the remote site such that it
ensures the survival of at least one site in the case of major disaster. For this reason, the
distance between the campus sites and the remote site often does not allow the use of
synchronous replication technologies because of the latency effects on write operations.

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 385
 Figure 7-36 shows a schematic representation of a three-site configuration that is based on
System z and DS8000 technology.

Figure 7-36 Three-site configuration

In this scenario, the application workload is usually running in a campus infrastructure.

Asynchronous mirroring technologies, such as DS8000 Global Mirror, are used to replicate
the data from the intermediate site (Site B) to the remote site (Site C). Combining HyperSwap
capability and Global Mirror management facilities, Tivoli Storage Productivity Center for
Replication for Open Systems provides a single point of control for data availability
management, monitoring, and alerting.

Figure 7-37 on page 387 shows a possible implementation of Tivoli Storage Productivity
Center for Replication for Open systems to manage the data availability for this scenario. In
this solution, an Active-Standby Tivoli Storage Productivity Center for Replication
configuration is deployed across two sites, with the active server running on the primary
storage site (Site A) and the Standby server in the remote site (Site C). An IP connection is
provided to manage the storage systems and to communicate with the z/OS HyperSwap
address spaces. A Metro Global Mirror session with HyperSwap enabled is defined to Tivoli
Storage Productivity Center for Replication to manage this kind of configuration. In addition to
the failure scenarios that were described for the Active-Active configuration, this Tivoli
Storage Productivity Center for Replication implementation provides protection from other
unplanned disastrous events.

386 Tivoli Storage Productivity Center for Replication for Open Systems
Figure 7-37 Tivoli Storage Productivity Center for Replication implementation for a three-site configuration

Figure 7-38 shows the entire Site B failure.

users

SITE A SITE B SITE C

..00101010.. ..00101010..
. .00
00101010
0101010..
...10010100.. ...1
. 00
..1 0010
0 0 100..
...10010100..
....11101010.. ....11101010..
....
.. 111 1 1010.
10
.....00110101.. ....
.. .00 0110101
.....00110101..1.

Data
replication

Production Campus

Data
replication Disaster Recovery Site

Figure 7-38 Intermediate site failure in a three-site configuration

Chapter 7. Managing z/OS HyperSwap from Tivoli Storage Productivity Center for Replication for Open Systems 387
 In this case, the disaster affects only the application that is running in Site B and the Parallel
Sysplex facilities can help to minimize the business effects. From the Disaster Recovery point
of view, the Tivoli Storage Productivity Center for Replication provides capabilities to restart
the replication to remote site directly from the primary site without requiring a full copy of the
data by using the Global Mirror Incremental Resync feature. Figure 7-39 shows a complete
production campus failure scenario.

users

SSITE
SITEE A SITE B SITE C

..00101010..
...10010100..
..00101010
..00101010..
00101010 0.. ..00101010..
..
. .00
. 00101010
101010.. ....11101010..
...10010
0 10 00
...10010100..0.. ...10010100..
...10010100.. .....00110101..
....11101010..
....1110
111
1 11 10
11 0100.. ....11101010..
....11101010 ..
.....00110101..
.....001
.001
. 001110
0101.
1 . .....00110101..
.....00110101 1..

Production Campus

Disaster Recovery Site

Figure 7-39 Production campus failure in a three-site configuration

A complete production campus failure is a Disaster Recovery scenario that requires a full
recovery of the operations to the remote site. Tivoli Storage Productivity Center for
Replication also offers all of the capabilities that are needed to perform the data recovery
operations and the functionalities to return to the original three-site configuration (Go-home
procedures).

388 Tivoli Storage Productivity Center for Replication for Open Systems
 8

Chapter 8. Hints and tips

In this chapter, we offer information that we encountered while we were writing this book that
might help you. It includes support references and helpful tips.

This chapter includes the following topics:

򐂰 Introduction
򐂰 VMware, DS8000, and Tivoli Storage Productivity Center for Replication
򐂰 DS8000 LSS symmetry
򐂰 HyperSwap enabled sessions troubleshooting
򐂰 Stuck in a particular state
򐂰 High availability server platforms
򐂰 Simple Network Management Protocol setup
򐂰 Tivoli Storage Productivity Center for Replication logging
򐂰 Auto refresh rate
򐂰 User authentication issues
򐂰 IBM Software Support Lifecycle
򐂰 Tivoli Storage Productivity Center support matrix

© Copyright IBM Corp. 2014. All rights reserved. 389

8.1 Introduction
In this chapter, we include the information that we found helpful at the time of this writing. We
advise that before you take any action, you search for the latest support bulletins and alerts
because the situation might be improved, was fixed, or new functionality might be added in
versions were released after this publication was produced.

For more information about supported hardware, platforms, and products for each Tivoli
Storage Productivity Center for Replication version, see this website:

http://www-01.ibm.com/support/docview.wss?uid=swg21386446

8.2 VMware, DS8000, and Tivoli Storage Productivity Center for

Replication
In this section, we describe some hints and tips for running VMware in a Tivoli Storage
Productivity Center for Replication environment. Also described are VMWare vStorage API
for Array Integration (VAAI) usage and tips for running with DS8000.

8.2.1 Hosting by using virtual servers

The main goal of the use of the VMware Compute Core feature is to virtualize server
resources and aggregate them in logical pools that can be allocated to multiple workloads.
vSphere ESXi is the virtualization layer that abstracts server hardware resources and shares
them with multiple virtual machines. By running vMotion, you can migrate running virtual
machines between hosts. However, if you install Tivoli Storage Productivity Center for
Replication into a virtual VMware server and run a vMotion, Tivoli Storage Productivity Center
for Replication often disables the communication between the Tivoli Storage Productivity
Center for Replication server and its managed storage resources.

Tip: Use the High Availability options that are available for Tivoli Storage Productivity
Center for Replication as described in 1.3, “Architecture” on page 7, and use dedicated
hardware resources to host Tivoli Storage Productivity Center for Replication server.

8.2.2 VAAI and DS8000

VMware VAAI uses specific functions from the storage array hardware to drive vSphere
vStorage operations.

For instance, for VAAI XCOPY, IBM FlashCopy at the track level is used. To use the VAAI
XCOPY primitive, the FlashCopy feature of the DS8870 must be enabled. This means that a
FlashCopy license for Fixed Block capacity is required.

In any instance in which XCOPY is not supported, the storage array indicates to the host that
XCOPY is not supported, and the host performs the copies. The only impact to applications is
that operations that might otherwise use XCOPY do not get the benefit of hardware
acceleration.

You should take the standard precautions concerning code versions compatibility. Check
code versions compatibility if you are planning to use VAAI with DS8000, and even more so if

390 Tivoli Storage Productivity Center for Replication for Open Systems
 you are planning to combine VAAI features with DS8000 Copy Services that are managed
directly or by using Tivoli Storage Productivity Center for Replication.

The first step is to make sure that you have the appropriate DS8000 firmware version.
Previous versions of DS8000 firmware had problems with the VAAI Zero Blocks/Write same
features, which can be easily solved with a firmware upgrade or a workaround. For more
information, see the Flash alert that is available at this website:

http://www-01.ibm.com/support/docview.wss?uid=ssg1S1004112

Check the IBM System Storage Interoperation Center (SSIC) and select the VMware
Operating System version that you use. The SSIC is available at this website:

http://www-03.ibm.com/systems/support/storage/ssic/interoperability.wss

The next step is to carefully plan your remote replication sessions and topology. Remember
the restrictions and limitations when you are cascading copy services across volumes. If you
plan to use VAAI XCOPY, the following restrictions apply:
򐂰 A Fixed Block FlashCopy license is required.
򐂰 Logical unit numbers (LUNs) are used by the ESX and ESXi servers must not be larger
than 2 TB. For optimal performance, use volumes of 128 GB or less.
򐂰 Track Space Efficient volumes and Extent Space Efficient volumes cannot be used.
򐂰 The target of an XCOPY operation cannot be a Remote Mirror source volume.

8.3 DS8000 LSS symmetry

Unlike the IBM ESS800 systems, logical subsystems (LSSs) are logical constructs in the IBM
System Storage DS8000 series. A single LSS can have volumes coming from different
physical arrays. This simplifies the LSS design layout; for example, with the possibility to
assign LSSs to applications without concern of the underlying physical disk resources.

LSSs play an important role on copy services sessions. In Metro Mirror, logical paths are
defined between source and target LSSs within source and target DS8000 Storage Systems.
These logical paths run through the physical links between the storage subsystems and are
unidirectional.

To avoid having issues with logical path limits on the DS8000s, we recommend that you
configure your remote copy sessions with a one-to-one, symmetrical LSS configuration. In the
DS8000, this is achieved by, for example, making all volumes that are defined in DS8000 #1
LSS 00 that are mirrored to remote DS8000 #2 have their respective target volumes, also in
LSS 00.

For more information, see IBM System Storage DS8000 Copy Services for Open Systems,
SG24-6788-06, which is available at this website:

http://publib-b.boulder.ibm.com/abstracts/sg246788.html?Open

8.4 HyperSwap enabled sessions troubleshooting

After a Tivoli Storage Productivity Center for Replication session configuration with
HyperSwap enabled is successfully loaded in the z/OS address spaces, the HyperSwap and

Chapter 8. Hints and tips 391

 freeze capabilities are delegated to the z/OS components. For this reason, any unplanned
event regarding the Metro Mirror is managed directly by z/OS address spaces, which leaves
only the management of planned actions and monitoring operations to Tivoli Storage
Productivity Center for Replication.

If a communication loss to z/OS address spaces occurs, Tivoli Storage Productivity Center for
Replication logs some error messages in the console that states that the communication to
the IOS was interrupted. Typical Tivoli Storage Productivity Center for Replication console
messages that indicate that the isolation between Tivoli Storage Productivity Center for
Replication and z/OS IOS are reported in Example 8-1.

Example 8-1 Tivoli Storage Productivity Center for Replication to IOS connection loss messages
IWNR5429E [2013-08-15 11:51:37.388-0700] The session ITSO-MM-HS has become
disconnected from IOS while a sequence was managed by HyperSwap. Tivoli Storage
Productivity Center for Replication is currently unable to manage HyperSwap, but a
HyperSwap might still occur.
IWNR7043E [2013-08-15 11:55:38.301-0700] Unable to connect to the host
192.0.0.4:5858

Although in most cases the communication loss is caused by network issues, some basic
checking can always be performed to verify the heath status of the HyperSwap z/OS
components, including the following checks:
򐂰 Determine whether the HyperSwap address spaces are running. This check can be
performed through System Display and Search Facility (SDSF) or by using z/OS Display
Active command, as shown in Example 8-2.

Example 8-2 Display Active (D A,L) command output

10.36.38 SYSTEM1 IEE114I 10.36.38 2013.219 ACTIVITY 917 C
JOBS M/S TS USERS SYSAS INITS ACTIVE/MAX VTAM OAS
00002 00018 00001 00038 00008 00001/00020 00012
LLA LLA LLA NSW S DFM DFM DFM NSW S
SDF SDF SDF OWT S JES2 JES2 IEFPROC NSW S
VLF VLF VLF NSW S DLF DLF DLF NSW S
SDSF SDSF SDSF NSW S IGVDGNPP IGVDGNPP IGVDGNPP OWT S
STGINIT STGINIT STGINIT OWT S RRS RRS RRS NSW S
VTAM1 VTAM1 VTAM NSW S TCAS TCAS TSO OWT S
APPC APPC APPC NSW S ASCH ASCH ASCH NSW S
TCPIP TCPIP TCPIP NSW SO INETD1 STEP1 IBMUSER OWT AO
FTP1 STEP1 IBMUSER OWT AO IWNSRV IWNSRV STEP1 IN SO
HSIBSOCK HSIBSOCK STEP NSW SO HSIBAPI HSIBAPI NSW S
IBMUSER OWT

򐂰 Review the Address Spaces job log for error messages.

򐂰 Check the HyperSwap configuration status. This check can be performed by using the
z/OS Display HyperSwap commands, as shown in the Example 8-3.

Example 8-3 Display HyperSwap command output

D HS,STATUS
RESPONSE=SYSTEM1
IOSHM0303I HyperSwap Status 797
Replication Session: ITSO-MM-HS
Socket Port: 5858
HyperSwap enabled

392 Tivoli Storage Productivity Center for Replication for Open Systems
 New member configuration load failed: Disable
Planned swap recovery: Disable
Unplanned swap recovery: Disable
FreezeAll: Yes
Stop: No

D HS,CONFIG
IOSHM0304I Active Configurations
Replication Session Name Replication Session Type
ITSO-MM-HS HyperSwap

򐂰 Check the devices status by using the z/OS Display Unit and Display Matrix commands.

8.5 Stuck in a particular state

If Tivoli Storage Productivity Center for Replication Session is stuck in a particular state, the
recommended workaround in this case is to stop and restart the Tivoli Storage Productivity
Center for Replication processes by using the following scripts:

Tip: Before the server is restarted, try running the Refresh States command from the
session drop-down menu.

򐂰 Windows:
– TPC_install_directory\scripts\stopTPCReplication.bat
– TPC_install_directory\scripts\startTPCReplication.bat
Default TPC_install_directory in Windows is C:\Program Files\IBM\TPC.
򐂰 AIX or Linux
– TPC_install_directory/scripts/stopTPCReplication.sh
– TPC_install_directory/scripts/startTPCReplication.sh
Default TPC_install_directory in AIX or Linux is /opt/IBM/TPC.

Example 8-4 shows an example of running scripts to start and restart the Tivoli Storage
Productivity Center for Replication server in Windows.

Example 8-4 Stop and Restart Tivoli Storage Productivity Center for Replication Server processes
C:\Program Files\IBM\TPC\scripts>stoptpcreplication.bat
Server replicationServer stop failed. Check server logs for details.
SUCCESS: The process with PID 3168 (child process of PID 4680) has been
terminated.

C:\Program Files\IBM\TPC\wlp\bin\server.bat status replicationServer

Server replicationServer is not running.

C:\Program Files\IBM\TPC\scripts>starttpcreplication.bat
C:\Program Files\IBM\TPC\scripts>

C:\Program Files\IBM\TPC\wlp\bin\server.bat status replicationserver

Server replicationserver is running.

Chapter 8. Hints and tips 393

 C:\Program Files\IBM\TPC\scripts>

8.6 High availability server platforms

When you are operating in a high availability environment, your Tivoli Storage Productivity
Center for Replication active server and standby server can be servers of the same operating
systems, or servers of different operating systems. For example, your active server can be a
Windows server and your standby server can be a Linux server or vice versa. A same-server
example is when your active server and your standby server both are AIX servers.

One such case of Tivoli Storage Productivity Center for Replication high availability is to have
your main site with the active server running on z/OS (in a Mainframe LPAR) and your
standby server running on a Windows server in the remote data center so that you do not
need a Mainframe LPAR for the standby server.

8.7 Simple Network Management Protocol setup

Tivoli Storage Productivity Center for Replication can be sent up by sending the Simple
Network Management Protocol (SNMP) traps to registered SNMP managers when various
events occur, including the following events:
򐂰 Session state change
򐂰 Configuration change
򐂰 Suspending-event notification
򐂰 Communication failure
򐂰 High-availability state change

You can use the mksnmp command-line interface (CLI) command to add a specified manager
to the list of servers to which SNMP alerts are sent. For more information about the mksnmp
command, see IBM TotalStorage Productivity Center for Replication Command-line Interface
User's Guide, SC32-0104, which is available at this website:

http://publib.boulder.ibm.com/infocenter/tivihelp/v4r1/index.jsp?topic=%2Fcom.ibm.
sspc_v13.doc%2Ffqz0_r_sspc_rep_publications.html

You can see the SNMP traps in the CsmTrace.log files, as shown in Figure 8-1. The figure
contains a segment of the log. As such, you can see the details of the trap that is captured
and prepared.

394 Tivoli Storage Productivity Center for Replication for Open Systems
 [2006-06-23 16:16:12.828-07:00] Work-2 RepMgr D
com.ibm.csm.server.session.snmp.SnmpNotification sendMsg TRACE: Message:
version=1 communityString=public
errorStatus=Success
operation=V2 TRAP requestId=0 correlator=0 (
1.3.6.1.2.1.1.3:17270546,
1.3.6.1.6.3.1.1.4.1:1.3.6.1.4.1.2.6.204.2.1.3,
1.3.6.1.6.3.1.1.4.3:1.3.6.1.4.1.2,
1.3.6.1.4.1.2.6.204.3.1:ess_gmsd_cli,
1.3.6.1.4.1.2.6.204.3.2:Preparing,
1.3.6.1.4.1.2.6.204.3.3:Prepared,
1.3.6.1.4.1.2.6.204.3.4:H1)
Figure 8-1 CsmTrace.log

Additionally, the Tivoli Storage Productivity Center for Replication Server can be set up to
receive SNMP traps from the IBM ESS model 800. Although they are not required, the use of
the SNMP alert reduces the latency between the time that a freeze event occurs and the time
that Tivoli Storage Productivity Center for Replication recognizes that the event is occurring.
With or without the SNMP alert function, however, Tivoli Storage Productivity Center for
Replication maintains data consistency of its sessions during the freeze event. The SNMP
trap destination can be set up on your ESS system via the ESS Specialist.

8.8 Tivoli Storage Productivity Center for Replication logging

If problems occur within your Tivoli Storage Productivity Center for Replication server
environment, there are several different ways that you can collect logs.

8.8.1 Collecting logs by using GUI

To collect logs via the Tivoli Storage Productivity Center for Replication GUI, click the
Advanced Tools in the menu. After you reach the Advanced Tools page, click Create.

8.8.2 Collecting logs by using CLI

You can also collect logs via the Tivoli Storage Productivity Center for Replication CLI. start
by opening a command prompt from your Tivoli Storage Productivity Center for Replication
server and enter mklogpkg and then press Enter. The command prompt displays the location
of the logs.

8.8.3 Collecting logs manually

The logs manually also can be collected manually. You can collect the Tivoli Storage
Productivity Center for Replication logs by compressing all of the files in the following
directories:
򐂰 C:\Program Files\IBM\IBM TotalStorage Productivity Center for Replication
V3.1\WAS\profiles\CSM\logs\
򐂰 C:\Program Files\IBM\IBM TotalStorage Productivity Center for Replication
V3.1\WAS\profiles\CSM\logs\CSM

Chapter 8. Hints and tips 395

8.9 Auto refresh rate
You can customize the auto refresh rate by going to the My Work panel on the left side on the
main menu and clicking Advanced Tools. The Advanced Tools panel opens. Under the Set
browser auto-refresh rate option, you can define the refresh rate for all non-wizard panels.
The default auto-refresh rate is 30 seconds.

This might be useful if you intend to use the Tivoli Storage Productivity Center for Replication
main window to provide a continuous, visual status of your data replication sessions.

8.10 User authentication issues

In this section, we describe how to address issues that might occur when you try to log on to
Tivoli Storage Productivity Center for Replication or add a user.

These issues often occur as a result of the following problems:

򐂰 Tivoli Storage Productivity Center internal web server (WebSphere Application Server) is
not running.
򐂰 There are firewall or network issues that are blocking communication from the Tivoli
Storage Productivity Center for Replication server.

8.10.1 An error is displayed when you try to log on

The error that is shown in Figure 8-2 on page 396 is displayed when you try to log on to Tivoli
Storage Productivity Center for Replication and an authentication issue occurred.

Figure 8-2 Log on error

396 Tivoli Storage Productivity Center for Replication for Open Systems
 First, try to determine whether the Tivoli Storage Productivity Center web server is working. If
it is running, check whether there are firewall or network issues. Also, check with your network
or security administrator if there were recent changes in network traffic policies.

If you cannot log in to check this problem by using any of the users you registered, you can try
to log on to Tivoli Storage Productivity Center for Replication by using the common user or the
user tpcFileRegistryUser. For more information about these default users, see 3.5.1,
“Adding Tivoli Storage Productivity Center users and groups to Tivoli Storage Productivity
Center for Replication” on page 94.

8.10.2 An error occurs when you try to add a user

If Tivoli Storage Productivity Center for Replication cannot access the repository that is used
for user authentication, you cannot add a user to Tivoli Storage Productivity Center for
Replication. Figure 8-3 on page 397 shows the error that is displayed when you try to add the
user from the Add Access wizard in the Tivoli Storage Productivity Center for Replication GUI.

Figure 8-3 Add user error

First, try to determine whether the Tivoli Storage Productivity Center web server is working. If
it is running, check whether there are firewall or network issues. Also, check with your network
or security administrator if there were recent changes in network traffic policies.

8.11 IBM Software Support Lifecycle

To determine whether your Tivoli Storage Productivity Center for Replication Version is still
supported or whether you should upgrade, browse to this IBM Software Lifecyle website:

http://www.ibm.com/software/support/lifecycle/index_t.html

Browse through the list of all products, starting with the letter T, or use your browser’s search
function to look for the product name or product ID (PID). The column on the right shows

Chapter 8. Hints and tips 397

 when the product was released and when the support ends. Select your products, and then
click View details at the bottom of the page. A list of only the selected products opens, to
which you can subscribe by using RSS technology.

8.12 Tivoli Storage Productivity Center support matrix

To find the Tivoli Storage Productivity Center support matrix for various components and
versions, browse to this Tivoli Storage Productivity Center support website:

http://www-01.ibm.com/support/docview.wss?uid=swg21386446

398 Tivoli Storage Productivity Center for Replication for Open Systems
 A

Appendix A. Tivoli Storage Productivity

Center for Replication and
Advanced Copy Services
In this appendix, Tivoli Storage Productivity Center for Replication integration with Advanced
Copy Services for PowerHA® System Mirror for i is introduced.

Advanced Copy Services (ACS) is a set of tools that was written by IBM Lab Services for IBM
i customers. These tools provide more functions for PowerHA SystemMirror for i that you can
use to simplify and customize your PowerHA SystemMirror for i runtime environment.

© Copyright IBM Corp. 2014. All rights reserved. 399

A.1 Integration with Tivoli Storage Productivity Center for
Replication
You can use ACS to manage Metro Mirror and Metro Global Mirror copy services for the
DS8000 storage systems that are in your environment.

Integration with Tivoli Storage Productivity Center for Replication is required to manage Metro
Global Mirror replication through ACS.

Integration with Tivoli Storage Productivity Center for Replication is also required to create
consistency groups for Metro Mirror replication through ACS. If you do not want to form
consistency groups for Metro Mirror replication, Tivoli Storage Productivity Center for
Replication is not required.

To manage Metro Global Mirror replication or Metro Mirror replication with consistency
groups, you must first create the following sessions in Tivoli Storage Productivity Center for
Replication and define these sessions in ACS. The sessions that you create depend on the
copy service that you want to manage:
򐂰 Metro Mirror Failover/Failback
򐂰 Metro Global Mirror

Figure A-1 shows the ACS and Tivoli Storage Productivity Center for Replication relationship
for a three-site DS8000 environment that uses Metro Global Mirror replication.

Figure A-1 DS8000 three-site disaster recovery solution with Metro Global Mirror

400 Tivoli Storage Productivity Center for Replication for Open Systems
 Note: For single-point administration, you should manage all functions and features for the
sessions, such as adding copy sets and starting the sessions, through ACS exclusively
after you define the sessions in ACS. Do not use the Tivoli Storage Productivity Center for
Replication GUI or command-line interface to manage the sessions.

For more information about ACS and Tivoli Storage Productivity Center, see the following
resources:
򐂰 PowerHA SystemMirror for IBM i Cookbook, SG24-7994, which is available at this
website:
http://publib-b.boulder.ibm.com/abstracts/sg247994.html?Open
򐂰 The IBM i Advanced Copy services wiki, which is available at this website:
https://www.ibm.com/developerworks/community/wikis/home?lang=en#!/wiki/IBM%20i%
20Advanced%20Copy%20Services

Appendix A. Tivoli Storage Productivity Center for Replication and Advanced Copy Services 401
402 Tivoli Storage Productivity Center for Replication for Open Systems
 B

Appendix B. Tivoli Storage Productivity

Center for Replication integration
In this appendix, Tivoli Storage Productivity Center for Replication integration with IBM Tivoli
System Automation Application Manager is introduced.

Tivoli System Automation Application Manager is an application that provides a single point
for managing heterogeneous business resources. These resources include applications,
services, mounted disks, and network addresses.

© Copyright IBM Corp. 2014. All rights reserved. 403

B.1 Integration with Tivoli Storage Productivity Center for
Replication
Tivoli System Automation Application Manager includes the Distributed Disaster Recovery
(DDR) feature that uses Tivoli Storage Productivity Center for Replication to provide a data
replication and disaster recovery solution for open systems. The DDR feature is available in
Tivoli System Automation Application Manager version 3.2 or later and requires Tivoli Storage
Productivity Center for Replication version 4.1.1.1 or later.

Tivoli System Automation Application Manager supports the Metro Mirror Failover/Failback
session for the following storage systems:
򐂰 ESS800
򐂰 DS6000
򐂰 DS8000
򐂰 SAN Volume Controller
򐂰 Storwize V3500
򐂰 Storwize V3700
򐂰 Storwize V7000
򐂰 Storwize V7000 Unified

Tivoli System Automation Application Manager uses Tivoli Storage Productivity Center for
Replication to manage replication between two sites. To enable Tivoli System Automation
Application Manager to use Tivoli Storage Productivity Center for Replication, you must
create a replication domain and references. The replication domain points to the Tivoli
Storage Productivity Center for Replication server or the server and the standby server in a
high availability environment. The replication references point to Tivoli Storage Productivity
Center for Replication sessions.

Note: For single-point administration, you should manage all functions and features for the
Tivoli Storage Productivity Center for Replication sessions through Tivoli System
Automation Application Manager exclusively after you define the replication domain and
references in Tivoli System Automation Application Manager. Do not use the Tivoli Storage
Productivity Center for Replication GUI or command-line interface to manage the sessions.

For more information about the integration of Tivoli Storage Productivity Center for
Replication with Tivoli System Automation Application Manager, including the steps that are
required to perform the integration, see Tivoli System Automation Application Manager
Administrator's and User’s Guide, which is available at this website:

http://www.ibm.com/developerworks/servicemanagement/dca/saam/resources.html

404 Tivoli Storage Productivity Center for Replication for Open Systems
 Figure B-1 shows the Tivoli System Automation Application Manager integration with Tivoli
Storage Productivity Center.

Figure B-1 Configuration for two-site disaster recovery

Appendix B. Tivoli Storage Productivity Center for Replication integration 405

406 Tivoli Storage Productivity Center for Replication for Open Systems
Related publications

The publications that are listed in this section are considered particularly suitable for a more
detailed discussion of the topics that are covered in this book.

IBM Redbooks
The following IBM Redbooks publications provide more information about the topics in this
document. Some publications that are referenced in this list might be available in softcopy
only:
򐂰 Tivoli Storage Productivity Center V5.2 Release Guide, SG24-8204
򐂰 IBM Tivoli Storage Productivity Center for Replication for Series z, SG24-7563
򐂰 IBM TotalStorage Productivity Center for Replication Using DS8000, SG24-7596
򐂰 IBM TotalStorage Productivity Center for Replication on Windows 2003, SG24-7250
򐂰 IBM TotalStorage Productivity Center for Replication on Linux, SG24-7411
򐂰 Implementing the IBM System Storage SAN Volume Controller V6.3, SG24-7933
򐂰 IBM System Storage SAN Volume Controller and Storwize V7000 Replication Family
Services, SG24-7574
򐂰 IBM System Storage DS8000 Copy Services for IBM System z, SG24-6787
򐂰 IBM System Storage DS8000 Copy Services for Open Systems, SG24-6788IBM System
Storage DS8000 Easy Tier Heat Map Transfer, REDP-5015
򐂰 IBM XIV Storage System Copy Services and Migration, SG24-7759

You can search for, view, download, or order these documents and other Redbooks,
Redpapers, Web Docs, draft, and other materials at the following website:
http://www.ibm.com/redbooks

Other publications
The following publications also are relevant as further information sources:
򐂰 IBM Tivoli Storage Productivity Center for Replication 5.2 for System z Installation and
Configuration Guide, SC27-4091
򐂰 IBM Tivoli Storage Productivity Center for Replication 5.2 for System z User’s Guide,
SC27-4092
򐂰 IBM Tivoli Storage Productivity Center for Replication 5.2 for System z Command-Line
Interface User’s Guide, SC27-4093
򐂰 IBM Tivoli Storage Productivity Center for Replication 5.2 for System z Problem
Determination Guide, SC27-4094
򐂰 IBM Tivoli Storage Productivity Center Version 5.2 Installation and Configuration Guide,
SC27-4058

© Copyright IBM Corp. 2014. All rights reserved. 407

Online resources
The following websites also are relevant as further information sources:
򐂰 IBM Tivoli Storage Productivity Center for Replication Information Center:
http://pic.dhe.ibm.com/infocenter/tivihelp/v59r1/index.jsp
򐂰 Tivoli Storage Productivity Center support website:
http://www-01.ibm.com/support/docview.wss?uid=swg21386446
򐂰 IBM Software Lifecyle website:
http://www.ibm.com/software/support/lifecycle/index_t.html
򐂰 Tivoli Storage Productivity Center Suite Customer Support Technical Information
Newsletter:
http://www-01.ibm.com/support/docview.wss?uid=swg27017347

Help from IBM

IBM Support and downloads:
http:///www.ibm.com/support

IBM Global Services:

http:///www.ibm.com/services

408 Tivoli Storage Productivity Center for Replication for Open Systems
Tivoli Storage Productivity Center
for Replication for Open Systems
Tivoli Storage Productivity Center for
Replication for Open Systems
Tivoli Storage Productivity Center for Replication for Open Systems
(0.5” spine)
0.475”<->0.873”
250 <-> 459 pages
Tivoli Storage Productivity Center for Replication for Open Systems
Tivoli Storage Productivity Center
for Replication for Open Systems
Tivoli Storage Productivity Center
for Replication for Open Systems
 Back cover ®

Tivoli Storage Productivity

Center for Replication
for Open Systems ®

Master Tivoli Storage This IBM Redbooks publication for the Tivoli Storage Productivity Center for
Replication for the Open environment walks you through the process of INTERNATIONAL
Productivity Center
establishing sessions, and managing and monitoring copy services through TECHNICAL
for Replication in Tivoli Storage Productivity Center for Replication. The book introduces SUPPORT
open systems enhanced copy services and new session types that are used by the latest IBM
storage systems. Tips and guidance for session usage, tunable parameters, ORGANIZATION
troubleshooting, and for implementing and managing Tivoli Storage
Manage replication Productivity Center for Replication’s latest functionality up to v5.2 also are
services from one provided. Tivoli Storage Productivity Center for Replication’s integration and
interface latest functionality includes Global Mirror Pause with Consistency, Easy Tier
Heat Map Transfer, and IBM System Storage SAN Volume Controller Change BUILDING TECHNICAL
Volumes. As of v5.2, you can now manage z/OS Hyperswap function from an INFORMATION BASED ON
Use all of the latest Open System. PRACTICAL EXPERIENCE
copy services IBM Tivoli Storage Productivity Center for Replication for Open Systems
features manages copy services in storage environments. Copy services are used by IBM Redbooks are developed
storage systems, such as IBM System Storage DS8000, SAN Volume by the IBM International
Controller, IBM Storwize V3700, V3500, V7000, V7000 Unified, and IBM XIV Technical Support
Storage systems to configure, manage, and monitor data-copy functions. Copy Organization. Experts from
services include IBM FlashCopy, Metro Mirror, Global Mirror, and Metro Global IBM, Customers and Partners
Mirror. from around the world create
This IBM Redbooks publication is the companion to the draft of the IBM timely technical information
Redbooks publication Tivoli Storage Productivity Center V5.2 Release Guide, based on realistic scenarios.
SG24-8204. It is intended for storage administrators who ordered and installed Specific recommendations
Tivoli Storage Productivity Center version 5.2 and are ready to customize Tivoli are provided to help you
Storage Productivity Center for Replication and connected storage. This implement IT solutions more
publication also is for anyone that wants to learn more about Tivoli Storage effectively in your
Productivity Center for Replication in an open systems environment. environment.

For more information:

ibm.com/redbooks

SG24-8149-00 0738439320