SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 1 of 6
Panel Name: Equip. No.: Dwg. Ref.

1. General Data and Information

BAY NO
BAY DESIGNATION
GIS MANUFACTURER

2. Name Plate Details

DETAILS GAS CIRCUIT BREAKER

MANUFACTURER
TYPE DESIGNATION
RATED VOLATGE
RATED CURRENT
RATED FREQUENCY
RATED SHORT-TIME WITHSTAND CURRENT
RATED BREAK TIME
APPLICABLE STANDARD
RATED PEAK WITHSTAND CURRENT
FIRST POLE TO CLEAR FACTOR
POWER FREQUENCY WITHSTND VOLTAGE
LIGHTING IMPULSE WITHSTAND VOLATAGE
RATED LINE CHARGING BREAKING CURRENT
RATED CABLE CHARGING BREAKING CURRENT
TYPE OF MECHANISM
RATED CONTROL VOLTAGE
RATED OPERATING SEQUENCE
DESIGN PRESSURE FOR ENCLOSURE
RATED SF6 PRESSURE @ 20 0 C
MINIMUM SF6 GAS DENSITY FOR INSULATION
CONTRACT NUMBER
SERIAL NO

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :
 SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 2 of 6
Panel Name: Equip. No.: Dwg. Ref.

YEAR OF MANUFACTURE

3. Mechanical Check and Visual Inspection

Mechanical check & Visual inspection was carried out as per TCS-P-105-Rev.01 Section 3.15.1
Refer the attached check list.

4. Electrical Test

Electrical tests are carried out as per TCS-P-105-Rev.01 Section 3.15.2. Refer the attached check list.

3.1) Contact Resistance Mesurement

MESURED AT SITE (µΩ) FACTORY TEST RESULTS (µΩ)

TEST
CURRENT
R Y B R Y B

100 A

3.2) Insulation Resistance Measurement

TEST VOLTAGE: 5 kV DC; CRITERIA: >1000 MΩ

CB
R-(Y+B+E) Y-(R+B+E) B-(R+Y+E) R-R’ Y-Y’ B-B’
POSITION

CLOSE - - -

OPEN - - -

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :
 SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 3 of 6
Panel Name: Equip. No.: Dwg. Ref.

3.3) Tests On Anti Pumping Relay

The anti-pump feature in the breakers was tested as follows:

1) The breaker was closed and the control switch was held in CLOSE position. It was ensured that the
breaker Closes.

2) The breaker was tripped:

2.a) Manually, 2.b) Electrically

3) It will be noted from the results below that the breaker does not attempt to re-close if a permanent closing
signal is applied.

TRIP SIGNAL BREAKER BREAKER

STEP OPERATION RESULTS
APPLIED OPERATION STATUS

1. Breaker control
switch switched to Breaker remains
NO Breaker CLOSES
“CLOSE” and held CLOSED
in CLOSE position.

Breaker control Breaker trips and

YES Breaker remains
2. switch held in does not attempt
Electrically OPEN
“CLOSE” position. to RECLOSE

Breaker control
switch returned to Breaker remains
3. NO None
NORMAL. OPEN

Breaker control
switch switched to
Breaker remains
4. “CLOSE” and held NO Breaker CLOSES
CLOSED
in CLOSE position.

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :
 SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 4 of 6
Panel Name: Equip. No.: Dwg. Ref.

Breaker control Breaker trips and

YES Breaker remains
5. switch held in does not attempt
mechanically OPEN
“CLOSE” position. to RECLOSE

3.4) Tests On Spring Charging Mechanism

SL.NO DESCRIPTION RESULT

1 Manual operation
Verification of correct spring status
2 A. Spring charged indication
B. Spring discharged indication
3 Spring charging time
4 Spring charging motor current (maximum/running) @ 125 volts

3.5) Timing Test

APPLIED CLOSING TIME IN mSec TRIPPING TIME IN mSec

CONTROL OPERATION
VOLTAGE R Y B R Y B
Close ----- ----- ------
125 VDC Trip-1 ----- ------ ------
Trip-2 ------ ------ ------
Close ------- ------ ------
Trip-1 ------ ------ ------
125 VDC
Close ------ ------ ------
Trip-2 ----- ------ ------
Trip-1 ----- ------ ------
Close ------ ------ ------
Trip-1 ------ ------ ------
125 VDC
Trip-2 ------ ------ ------
Close ------ ------ ------
Trip-2 ------ ------ ------

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :
 SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 5 of 6
Panel Name: Equip. No.: Dwg. Ref.

Criteria

1. Close : < As per FAT Report

2. Open : < As per FAT Report

3.6) Closing/Opeing At Minimum/Maximum Control Voltage

SL.NO OPERATION CONTROL VOLTAGE R PHASE Y PHASE B PHASE REMARKS

1. CLOSING 90 V DC
Minimum

2. CLOSING 140 V DC
Maximum

TC1
4. TRIPPING 70 V DC
Minimum TC2

TC1
6. TRIPPING 140 V DC
Maximum TC2

CLOSE - TC1
7. 90 V DC
OPEN
TC2

CLOSE - TC1
9. 140 V DC
OPEN
TC2

For detailed results refer the attachments.

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :
 SITE TEST REPORT

Customer:

Name of Substation: Contract No. :

CIRCUIT BREAKER - TEST REPORT Page 6 of 6
Panel Name: Equip. No.: Dwg. Ref.

3.7) Closing/Tripping Coil Current Measurement

SL.NO OPERATION CONTROL VOLTAGE CURRENT IN AMPS REMARKS

1 CLOSING 125 V

2 OPENING (TC-1) 125 V

3 OPENING (TC-2) 125 V

4. General Checks

DESCRIPTION REMARKS
Visual Inspection
Manual operation of Spring charging mechanism
Spring status indication
Local Position Indication on CB
LCC Semaphore Indication
Manual Closing and Tripping
Functioning of CB operation counter
Anti condensate heating
Auxiliary Contact check

5. Testing Equipments Used

Item Test Equipment Serial Number Calibration date Calibration due date
1
2

Date :
Testing Engineer Engineer
Witnessed By
Signature: Signature:
Name : Name :