SUPPLEMENT

SERVICE MANUAL
Subject: Change of IF Signal Process IC
This service manual supplement is for the ST413E/
6413TE/DWT1304/ST419E/6419TE changed IC Example: ST419E
model, which are different from the previous ST413E/ Rating label
6413TE/DWT1304/ST419E/6419TE model. For the
ST413E/6413TE/DWT1304/ST419E/6419TE changed
IC model, an “A” has been added to the end of the
model number on rating label in the rear. Refer to the
rating label illustration at right.
This service manual shows only the differences
Suffix "A"
between the model ST413E/6413TE/DWT1304/
ST419E/6419TE changed IC model and the previous ST413E/6413TE/DWT1304/
ST419E/6419TE model. All other information is described in the service manual of the
previous ST413E/6413TE/DWT1304/ST419E/6419TE model.

13″ COLOR TELEVISION

ST413E/6413TE DWT1304

19″ COLOR TELEVISION

ST419E/6419TE
 IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and de-
scribed in this service manual are effective methods of performing service
operations. Some of these service special tools should be used when and
as recommended.

It is important to note that this service manual contains various CAUTIONS

and NOTICES which should be carefully read in order to minimize the risk of
personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to under-
stand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai
could not possibly know, evaluate and advice the service trade of all con-
ceivable ways in which service might be done or of the possible hazardous
consequences of each way. Consequently, Funai has not undertaken any
such broad evaluation. Accordingly, a servicer who uses a service proce-
dure or tool which is not recommended by Funai must first use all precau-
tions thoroughly so that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.

TABLE OF CONTENTS
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Schematic Diagrams / CBA's and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
ST413E changed IC model
Different parts from the previous version model (ST413E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
6413TE changed IC model
Different parts from the previous version model (6413TE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
DWT1304 changed IC model
Different parts from the previous version model (DWT1304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
ST419E changed IC model
Different parts from the previous version model (ST419E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
6419TE changed IC model
Different parts from the previous version model (6419TE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
 RF/IF SIGNAL VIDEO SIGNAL AUDIO SIGNAL

IC31 (IF SIGNAL PROCESS) WF1

SF1 CF31 MAIN CBA
SAW 16 VIF VIDEO 4.5MHz EQ
FILTER 4 2 1
17 AMP DET TRAP AMP
WF6
CF32
TO
TU1 VCO 4.5MHz FM AF
7 9 TU-AUDIO AUDIO/POWER
FILTER DET AMP CONTROL BLOCK
IF 11

LPF
RF
AGC 1 14 AGC
SCL 4 IF AGC DET
SDA 5
EXT.CLK 8 AFT

AMP VCO F/B 6

WF16 Q31

11 13 18

TO SCL
AUDIO/POWER IC111
CONTROL BLOCK SDA TV MICON/VIDEO X301
/AUDIO/CHROMA 3.58MHz
/DEFLECTION 73 75 16 63 RCV101
IC151
(MEMORY) AFT AGC-IN EXT-H RCV-IN 70 REMOTE
SENSOR
CS 7 72 I2C-OPEN
KEY-IN1 66 KEY
SCL 6 58 SCL

1-1
KEY-IN2 69 SWITCH
SDA 5 56 SDA
IF/Video/System Control Block Diagram

32 VCXO
PROTECT-1
(NO CONNECTION) CN301 TO
PROTECT-2
POWER SUPPLY BLOCK
I2C-OPEN 2 P-ON-H 79 P-ON-H
SDA 4 PROTECT-1 68 PROTECT-1
SCL 5 TO
PROTECT-2 67 PROTECT-2
CRT/H.V. BLOCK
CN301 is used for 26 PROTECT-3 76 PROTECT-3
TUNER
adjustment at factory LUMINANCE
PROCESS
BLOCK DIAGRAMS

CIRCUIT WH301A
24 LINE RGB MATRIX OSD SW RGB DRIVE 52 5 BLUE
JK701 TO
/COLOR CONT /CONTRAST /CUT OFF 51 4 GREEN
VIDEO-IN /BRIGHTNESS /H.V. BLK CRT/H.V. BLOCK
CHROMINANCE 50 3 RED WH301B
PROCESS
WF2 CIRCUIT
LPF

14

11 OSD

H-SYNC
PROCESS 53 ACL
CIRCUIT 46 H-DRIVE
TO
45 FBP
CRT/H.V. BLOCK
V-SYNC 38 V-DRIVE
PROCESS 37 V-RAMP-F/B
CIRCUIT

L2200XBLIF
 SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS
Standard Notes
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often
pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement compo-
nents rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are
identified in this manual and its supplements; electrical components having such features are identified by the
mark " # " in the schematic diagram and the parts list. Before replacing any of these components, read the parts
list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteris-
tics as specified in the parts list may create shock, fire, or other hazards.

Note:
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K=103, M=106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P=10-6µF).
5. All voltages are DC voltages unless otherwise specified.

Note of Capacitors:
ML --- Mylar Cap. PP --- Metallized Film Cap. SC --- Semiconductor Cap. L --- Low Leakage type

Temperature Characteristics of Capacitors are noted with the following:

B --- ±10% CH --- 0±60ppm/°C CSL --- +350~-1000ppm/°C

Tolerance of Capacitors are noted with the following:

Z --- +80~-20%

Note of Resistors:
CEM --- Cement Res. MTL --- Metal Res. F --- Fuse Res.

Capacitors and transistors are represented by the following symbols.

CBA Symbols Schematic Diagram Symbols

(Top View) (Bottom View)
+ Digital Transistor
Electrolytic Capacitor

(Bottom View)
Transistor or Digital Transistor
E C B
(Top View) (Top View)

NPN Transistor PNP Transistor

ECB ECB
(Top View) (Top View)

NPN Digital Transistor PNP Digital Transistor

ECB ECB

2-1 L13SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.

2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective
before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the pow-
er supply circuit to fail.
3. Note:
(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Wire Connectors
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).
(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).
5. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:

1 2 3
5.0 5.0 Power on mode
(3.0) (3.0) Power off mode
Voltage
Indicates that the voltage Unit: Volts
is not consistent here.

6. How to read converged lines

1-D3
Distinction Area
Line Number 3 1-B1
(1 to 3 digits) AREA D3

2 AREA B1
Examples:
1. "1-D3" means that line number "1" goes to the line
number "1" of the area "D3". 1 1-D3
2. "1-B1" means that line number "1" goes to the line
number "1" of the area "B1". A B C D

7. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.

2-2 L13SC
Main 2/3 Schematic Diagram
CAUTION ! NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. hot GND as a common terminal.
4A/125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

MAIN 2/3
Ref No. Position
ICS
IC31 I-3
IC601 I-1
TRANSISTORS
Q31 H-4
Q601 J-2
Q602 J-1
Q662 I-1
Q671 H-2
Q675 H-1
Q676 H-1
Q681 G-2
Q682 G-1
Q683 G-1
CONNECTOR
CN691 K-2
VARIABLE RESISTOR
VR661 H-1

1 NOTE:
*These components (C643, C642, JS642)
can be used in any models.
However, you cannot mix components under
Group A with the ones under Group B.
You can choose either Group. The difference
between Group A and Group B is shown below.
Group A Group B
C643 0.01/250V 4700P/250V
C642 0.01/250V Not Used
JS642 Not Used WIRE

2-3 L2200XSCM2
Main CBA Top View
CAUTION ! Because a hot chassis ground is present in the power
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, supply circuit, an isolation transformer must be used.
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. Also, in order to have the ability to increase the input
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V slowly,when troubleshooting this type power supply
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail. circuit, a variable isolation transformer is required.
NOTE: MAIN CBA
TP601
The voltage for parts in hot circuit is measured using Ref No. Position
+B
hot GND as a common terminal. ICS
IC31 B-1
IC111 D-1
IC151 E-2
IC551 B-2
IC601 C-4
IC801 E-1
FOCUS-VR TRANSISTORS
(UPPER SIDE) Q31 C-1
Q111 E-2
Q321 C-1
Q571 B-3
Q572 B-2
SCREEN-VR Q601 B-4
(LOWER SIDE) Q602 B-4
Q662 C-3
TP300 Q671 C-3
GND Q675 C-2
Q676 C-2
Q681 D-3
Q682 D-3
Q683 D-3
CONNECTORS
CN571 A-3
CN691 C-4
CN801 D-1
WH301A C-2
WH501A A-2
TEST POINTS
TP300 A-3
TP601 A-4
VARIABLE RESISTOR
VR661 A-1

VR661
+B ADJ

2-4 BL2300F01011-1
Main CBA Bottom View
CAUTION ! Because a hot chassis ground is present in the power
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, supply circuit, an isolation transformer must be used.
If Main Fuse (F601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. Also, in order to have the ability to increase the input
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V slowly,when troubleshooting this type power supply
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail. circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

WF8
Q571
Base

WF7
Q572
Collector

WF9
PIN 1
OF CN571
WF12
PIN 4
OF CN571

WF10
PIN 3
OF WH501A
WF11
PIN 7
OF IC551
WF1
PIN 2
OF IC31
WF16
PIN 8
OF TU1
WF6
PIN 9
OF IC31
WF2
PIN 14
OF IC111

2-5 BL2300F01011-1
CRT CBA Top View CRT CBA Bottom View

CRT CBA
Ref No. Position
TRANSISTORS
Q501 B-2
Q502 B-2
Q503 B-2
CONNECTORS
CN501 A-1
WH301B B-1
WH501B B-1

WF4 WF14 WF3 WF15

Q502 Q502 Q501 Q501
Base Collector Base Collector

WF13
Q503
Collector
WF5
Q503
Base

2-6 BL2300F01011-2
ST413E changed IC model
Different parts from the previous version model (ST413E)
Ref. No. Description Part No.
MECHANICAL PARTS
A4# RATING LABEL L2200XA ----------
S6 SERIAL NO. LABEL L2200XA ----------

ELECTRICAL PARTS
MMA CBA 0ESA05976
MAIN CBA ----------
C38 Not Used
C609 CERAMIC CAP. B K 1000pF/2KV CCD3DKD0B102
IC31 IC:VIF/SIF M61113FP TF0G QSZBA0SHT035
R38# CHIP RES.(1608) 1/10W J 12k Ω RRXAJB5Z0123
R132 Not Used

6413TE changed IC model

Different parts from the previous version model (6413TE)
Ref. No. Description Part No.
MECHANICAL PARTS
A4# RATING LABEL L2201XB ----------
S6 SERIAL NO. LABEL L2201XB ----------

ELECTRICAL PARTS
MMA CBA 0ESA05976
MAIN CBA ----------
C38 Not Used
C609 CERAMIC CAP. B K 1000pF/2KV CCD3DKD0B102
IC31 IC:VIF/SIF M61113FP TF0G QSZBA0SHT035
R38# CHIP RES.(1608) 1/10W J 12k Ω RRXAJB5Z0123
R132 Not Used

DWT1304 changed IC model

Different parts from the previous version model (DWT1304)
Ref. No. Description Part No.
MECHANICAL PARTS
A4# RATING LABEL L2204XE ----------
S6 SERIAL NO. LABEL L2204XE ----------

ELECTRICAL PARTS
MMA CBA 0ESA05976
MAIN CBA ----------
C38 Not Used
C609 CERAMIC CAP. B K 1000pF/2KV CCD3DKD0B102
IC31 IC:VIF/SIF M61113FP TF0G QSZBA0SHT035
R38# CHIP RES.(1608) 1/10W J 12k Ω RRXAJB5Z0123
R132 Not Used

3-1 L2200XPL
ST419E changed IC model
Different parts from the previous version model (ST419E)
Ref. No. Description Part No.
MECHANICAL PARTS
A4# RATING LABEL L2300XA ----------
S6 SERIAL NO. LABEL L2300XA ----------

ELECTRICAL PARTS
MMA CBA 0ESA05979
MAIN CBA ----------
C38 Not Used
C609 CERAMIC CAP. B K 1000pF/2KV CCD3DKD0B102
IC31 IC:VIF/SIF M61113FP TF0G QSZBA0SHT035
R38# CHIP RES.(1608) 1/10W J 12k Ω RRXAJB5Z0123
R132 Not Used

6419TE changed IC model

Different parts from the previous version model (6419TE)
Ref. No. Description Part No.
MECHANICAL PARTS
A4# RATING LABEL L2301XB ----------
S6 SERIAL NO. LABEL L2301XB ----------

ELECTRICAL PARTS
MMA CBA 0ESA05979
MAIN CBA ----------
C38 Not Used
C609 CERAMIC CAP. B K 1000pF/2KV CCD3DKD0B102
IC31 IC:VIF/SIF M61113FP TF0G QSZBA0SHT035
R38# CHIP RES.(1608) 1/10W J 12k Ω RRXAJB5Z0123
R132 Not Used

3-2 L2200XPL
 ST413E/6413TE/DWT1304/ST419E/6419TE
L2200XA/L2201XB/L2204XE/L2300XA/L2301XB
2005-03-10