1. A machine part that supports another part, A.

Light
which rotates, slides or oscillateds in or on it B. Medium
A. Journal C. Heavy
B. Bearing D. Extra heavy
C. Roller 11. Refers to the axial distance from a point on
D. Casing one coil to the corresponding point on the
2. The part of a shaft or crank which is next adjacent coil.
supported by and turns in bearing. A. Lead
A. Casing B. Spring distance
B. Bushing C. Pitch
C. Roller D. Spring deflection
D. Journal 12. The spring index for general industrial uses
3. It is also called anti-friction bearing. should be
A. Rolling bearing A. 5 to 7
B. Thrust bearing B. 6 to 8
C. Tapered bearing C. 7 to 9
D. Single row bearing D. 8 to 10
4. Which of the following is a bearing material? 13. What is the spring index of valve and
A. Babbitt clutch?
B. Bronze A. 3
C. Plastics B. 5
D. All of the above C. 7
5. It acts toward the center of the bearing D. 9
along a radius. 14. Refers to the space between adjacent coils
A. Thrust load when the spring is compressed to its
B. Tangential load operating length
C. Radial load A. Coil allowance
D. Peripheral load B. Coil tolerance
6. Conrad bearing is also known as C. Coil clearance
A. Needle bearing D. None of these
B. Ball bearing 15. The most practical spring designs produce a
C. Roller bearing pitch angle is less than
D. Tapered bearing A. 12°
7. The combined effect of many of the B. 15°
variables involved in the operation of a C. 20°
bearing under hydrodynamic lubrication can D. 25°
be characterized by the dimensionless 16. Engine valves get shut by means of
number called: A. Valve lock
A. Reynolds Number B. Tappet
B. Prandtl Number C. Valve spring
C. Grashof Number D. Adjusting screw
D. Sommerfeld Number 17. Which of the following materials is used for
8. It exits primarily to guide the motion of a leaf and coil spring?
machine member without specific regard to A. AISI 3140
the direction of load application. B. AISI 3150
A. radial bearing C. AISI 3240
B. Journal bearing D. AISI 4063
C. Thrust bearing 18. The circumference of a coil spring times the
D. Guide bearing effective number of coils is called
9. It carries a load collinear to the axis of A. Active length
possible rotation of the supported member. B. Solid length
A. Guide bearing C. Compressed length
B. Journal bearing D. Operating length
C. Thrust bearing 19. For spring subjected to light service, the
D. Radial bearing factor of safety __________ is suggested
10. The 400 series bearing is called: A. 1.5
 B. 2.0 29. In the mechanical brake system the main
C. 2.5 function is of
D. 3.0 A. spring
20. Refers to a flat or curved made of thin B. cam
superimposed plates and formin a cantilever C. shoe adjuster
or beam of uniform strength. D. shoe rivets
A. Laminated spring 30. In the motor vehicles, there is a _________ in
B. Graduated spring addition of foot brake
C. Full spring A. hand brake
D. Conical spring B. hydraulic brake
21. The efficiency of hydraulic braking system is C. mechanical brake
A. about 90% D. band brake
B. 60-80 % 31. the breaking strength of oak tanned belting
C. 50-60 % varies from 3 to more than
D.40-50 % A. 5 ksi
22. The SAE recommends an angle of B. 6 ksi
_________ for cone clutches faced with C. 7 ksi
leather asbestos or having cork inserts. D. 8 ksi
A. 7.5 degrees 32. if the ends are joined by wire lacing with machine
B. 9.5 degrees the usual efficiency of joint is
C. 12.5 degrees A. 75 %
D. 14.5 degrees B. 85 %
23. Why does a clutch creates noise? C. 88 %
A. Clutch release bearing is either dry or D. 100 %
defective 33. The tension in the belt due to centrifugal force
B. Clutch spring is broken increases rapidly above
C. Clutch is faulty A. 2500 fpm
D. all of the above B. 3000 fpm
24. what faults develop in the brakes? C. 3500 fpm
A. brakes do not work properly D. 4000 fpm
B. brakes do not disengage 34. Experience suggest s that the most economical
C. brakes makes noise designs are obtained for a belt
D. all of the above Speed of
25. which of the following types of brakes are A. 2000 to 3000 fpm
also changed while replacing brake lining? B. 3000 to 4000 fpm
A. brake shoes C.4000 to 4500 fpm
B. shoe rivets D. 4000 to 4000 fpm
C. shoe spring 35. For leather belts recommended speed is
D. block brake A. 2000 to 300 0 fpm
26. Power brakes require _________ power. B. 4000 to 5000 fpm
A. equal C. 6000 to 7500 fpm
B. less D. 7000 to 8000 fpm
C. more 36. for fabric belts recommended speed is
D. pulsating A. 2000 to 3000 fpm
27. What type of oil used in the hydraulic B. 2000 and more fpm
system? C. 3000 to 4000 fpm
A. Engine oil D. 4000 to 4500 fpm
B. Gear oil 37. on high speed centrifugal blowers, it has been
C. Brake oil observed that the arc of contact reduced from 180
D. Clutch oil degrees at rest to___ in motion
28. The principal parts of a hydraulic brake A. 90 deg
system are the master cylinder and the B.95 deg
A. multi cylinder C. 100 deg
B. wheel cylinder D. 110 deg
C. brake wire 38. the recommended initial tension of belt is
D. brake shoe A. 75 lb/in of width
B. 71 lb/in of width A. lead
C. 73 lb/in of width B. module
D. 80 lb/in of width C. involute
39. the recommended net belt pull for rubber belt is D. clearance
A. 11.34 lb/ply per inch of width 48. for evenly distributed and uniform wear on each
B. 13.75 lb/ply per inch of width meshing gear tooth the ideal design practice is to
C. 16.35 lb/ply per inch of width consider a
D. 20.34 lb/ply per inch of width A. wear resistance alloy addition to tooth gear
40. if two intersecting shafts are to be belt connected B. heat treatment of the gears
how many guide pulley is used. C. hardening of each
A. 1 D. hunting tooth addition
B. 2 49. _________ used to transmit power at high
C. 3 velocity ratios between non- intersecting shafts that
D. 4 are usually but not necessarily at right angle
41. the distance helical gear worm would thread A. helical gear
along its axis in one revolution if it were free to move B. bevel gear
free to move axially is called C. worm gear
A. lead D. spiral gear
B. thread 50. a gear design, the ratio of the pitch diameter in
C. pitch inches to the number of teeth is called
D. land A. module
42. range of helix angle on helical gear is ________ B. diametral pitch
A. less than 18 C. English module
B. 15-25 D. circular pitch
C. 20-35 51. A circle the radius of which is equal to the
D. 35-40 distance from the axis to the pitch point
43.what will be the effect in bushing gears without A. pitch circle
backlash? B. root circle
A. jamming C. base circle
B. overheating D. outside circle
C. overload 52. ratio of pitch diameter to the number of teeth.
D. all of these A. diametral pitch
B. module
44. the amount by which the width of a tooth space C. contact ratio
exceeds the thickness of the engaging tooth on the D. helical overlap
pitch circles. 53. a kind of gear used for heavy duty works where
A. backlash a large ratio of speed is required and are extensively
B. clearance used in speed reducer is known as
C. undercut A. worm gear
D. chordal thickness B. spiral gear
45. height of tooth above pitch circle or radial C. helical gear
distance between pitch circle and top land of the D. bevel gear
tooth is called 54. the ratio of the number of teeth to the number of
A. top tooth mm of pitch diameter equals number of gear teeth to
B. addendum each mm pitch diameter.
C. land A. diameter pitch
D. hunting B. Module
46. I involutes teeth, the pressure angle is often C. Circular pitch
defined as the angle between the line of action and D. English module
the line of tangent to the pitch circle. It is termed as 55. the depth of tooth space below the pitch circle
A. helix angle A. dedendum
B. angle of recess B. working depth
C. angle of obliquity C. full depth
D. arc of action D. tooth depth
47. the reciprocal of a diametral pitch or the ratio of 56. the total depth of a tooth space equal to
pitch diameter to number of teeth is called addendum plus dedendum
A. full depth C. Miter gear
B. working depth D. Tangent gear
C. whole depth 66. The used of gearbox provides
D. dedendum A. gear leverage
57. a circle coinciding with a tangent to the bottom of B. more torque
the tooth space C. more speed
A. root circle D. none of these
B. pitch circle 67. For equalizing the rotation of two gears, a
C. addendum circle gearbox employs.
D. dedendum A.dog and clutch
58. the diameter of a circle coinciding with the top of B. crown gear
the teeth of an internal gear C. star pinion
A. pitch diameter D. none of these
B. root diameter 68. In a constant mesh gearbox, all the speed gears
C. internal diameter remain
D. central diameter A. separate
59. a gear with teeth on the outer cylindrical surface B. joined to their couples
A. outer gear C. of the same measurements
B. external gear D. none of these
C. spiral gear 69. If a big gear moved by the small gear then the
D. helical gear big gear
60. addendum of a cycloidal gear tooth. A. will not rotate
A. cycloid B. will rotate on reverse direction
B. epicycloids C. will rotate fastly
C. straight rack D. none of these
D. involute 70. ______are bevel gears mounted on intersecting
61 .The spiral bevel gears are recommended when shaft at angle of other than 90 degrees.
the pitch line speed exceeds A. Right angle gears
A.1000 rpm B. Half gears
B.1100 rpm C. Inclined gears
C.1500rpm D. Angular gears
D.2000 rpm 71. The smallest diameter on a gear tooth with which
62. When the pitch line speed is above 8000 fpm the the mating gear makes. .
teeth should be A. Idler
A. ground after hardening B. Pinion
B. should be cooled in air C. Gear
C. should be quenched after D. Central diameter
D. none of these 72.The ratio of the arc of action to the circular pitch
63. ______have curved teeth as in spiral bevels, but is known as
with zero spiral angles. A. Contact ratio
A. Spiral gears B. Action ratio
B. Zerol bevel gears C. Recess action
C. Zero bevel gears D. Approach ratio
D. Straight bevel gears 73. The curved that satisfy the law of gearing.
64. ______is a gear that has an advantage of A. Tooth profile
smoother tooth engagement quietness of operation B. Stub curve
greater strength and higher permissible speeds. C. Conjugate curve
A. Zerol bevel gears D. Involute curve
B. Straight bevel gears 74. The depth tooth space below the pitch circles or
C. Hypoid bevel gears the radial dimension between the pitch circle and
D. Spiral bevel gears the bottom of the tooth space.
65. When the pair of bevel gears of the same size is A. Addendum
on shafts intersecting at right angle, they are called B. Dedendum
______. C. Working Depth
A. Mold gear D. Whole depth
B. Helix angle 75. The circle that bounds the bottoms of the teeth.
A. Addendum circle C. one-half
B. Pitch circle D. two-third
C. Base circle 84. To avoid charring by the heat of friction, rawhide
D. Dedendum circle gears should not be operated of pitch line velocities
76. The ratio of the number of teeth to the number of greater than_________.
millimeters of pitch diameter. A. 2500 fpm
A. Diameter pitch B. 3000 fpm
B. Module C. 3500 fpm
C. Circular pitch D. 4000 fpm
D. Base pitch 85. The outside diameter of the hubs of larger gears
77. The Diameter pitch circulated in the normal plane should be ____ the bore for steel.
and is equal to the pitch divide d by the cosine of A. 1.5 times
helix angle. B. 1.6 times
A. Normal diametral plane C. 1.7 times
B. Normal diametral pitch D. 1.8 times
C. Normal plane 86. The outside diameter of the hubs of larger gears
D. Normal axial pitch should be ____ the bore for iron.
78. That portion of the face width that actually A. 1.5 times
comes into contact with mating teeth, as B. 1.8 times
occasionally one member of a pair of gears may C. 2.0 times
have a grater face width than the other is called D. 2.5 times
A. effective face width 87 .Helix angles of _____ degrees are preferred for
B. effective tooth face single helical gears.
C. effective tooth thickness A. 10 and 18
D. effective tooth flank B. 12 and 20
79. The actual torque ratio of a gear set divided by C. 15 and 23
its gear ratio. D. 18 and 28
A. Coefficient of performance 88. Helix angles of _____ degrees are preferred for
B. Transmission ratio double helical gears.
C. Ratio factor A. 15 and 25
D. Efficiency B. 20 and 30
80. When it rolls along the outer side of another C. 25 and 40
circle, it is called D. 30 and 45
A. cycloid 89. A _______ is a spur gear of infinite diameter.
B. hypocloid A. hypoid
C. epicycloids B. herring bone
D. trochoid C. annular
D. rack
81. They are cylindrical in form operate on parallel 90. It is standard practice to assume that the
axes and have straight teeth parallel to the axis. thickness of the tooth measured around the pitch
A. Helical gears circle is exactly______ of the circular pitch.
B. Bevel gears A. one-forth
C. Spur gears B. one-third
D. Worm gears C. one-half
82. The design stress was based upon the ultimate D. two-third
strength of the material with a factor of safety of 91. The __________ traced by the outermost corner
about____________. of one tooth on the plane of the other gear.
A. 2 A. cycloid
B. 3 B. hypocycloid
C. 4 C. epitrochoid
D. 5 D. trochoid
83. Safe working stress for common gear materials 92. An imaginary circle passing through the points at
operating at very low velocities are usually assumed which the tooth of the meshing gears contact each
to be _______ the ultimate strength. other.
A. one-forth A. Pitch circle
B. one-third B. Base circle
C. Addendum circle D. Bevel gear
D. Dedendum circle 100. The angle between the plane of the pitch circle
93. A gear with teeth on the outer cylindrical surface. and a plane tangent to the large end of the tooth.
A. Rack gear A. Front angle
B. Zerol gear B. Back angle
C. Miter gear C. Dedendum angle
D. External gear D. Face angle
94. The diameter of a circle coinciding with the top
of the teeth of an internal gear.
A. Dedendum diameter
B. Pitch diameter
C. Base diameter
D. Internal diameter
95. It is standard practice to assume that the
thickness of the tooth measured around the pitch
circle is exactly ________ the circle pitch.
A. One half
B. One third
C. One fourth
D. One fifth
96. The helix angles for the herringbone gears are
used from ___________ for industrial gears.
A. 10 to 15
B. 15 to 20
C. 20 to 30
D. 25 to 45
97. The distance parallel to the axis from the pitch
circle to the face of the shoulder or hub.
A. back cone
B. backing
C. crown height
D. apex distance
98. A machine that makes gear teeth by means of a
reciprocating cutter that rotates slowly with the work.
A. Gear forming
B. Gear hobber
C. Gear shaper
D. Gear cutter
99. A type of gear wheels connecting non parallel,
non intersecting shafts usually at right angles.
A. Helical gear
B. Herringbone gear
C. Hypoid gear