Scribd
Upload
6 views

OpeManualForCNC_E

This operation manual provides detailed procedures for obtaining parameter files, system configuration files, and CNC ID files from various CNC display units, including 8.4/10.4-inch, 15/19-inch, and iHMI screens. Each section outlines specific steps to follow, including the use of USB memory or memory cards, and how to revert any changes made to parameters. Additionally, guidance is provided for troubleshooting if screens do not appear as expected.

Uploaded by

vinren
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
6 views

OpeManualForCNC_E

This operation manual provides detailed procedures for obtaining parameter files, system configuration files, and CNC ID files from various CNC display units, including 8.4/10.4-inch, 15/19-inch, and iHMI screens. Each section outlines specific steps to follow, including the use of USB memory or memory cards, and how to revert any changes made to parameters. Additionally, guidance is provided for troubleshooting if screens do not appear as expected.

Uploaded by

vinren
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Fanuc Corporation

3/7/2019

Operation manual

for file output on CNC

This operation manual explains the procedure to get Parameter file, system configuration
file and CNC ID file on CNC. The procedure is slightly different by CNC display size or
screen specification. Refer to the corresponding chapter.

1. For 8.4/10.4-inch display unit


2. For 15/19-inch display unit
3. For iHMI screen (Procedure to display a conventional screen)
4. If any screen doesn’t appear

Screen for 10.4” display unit Screen for 15” display unit Screen for iHMI
Fig. 1 For screen examples

1 For 8.4/10.4-inch display unit


1. Turn on the machine and activate the CNC.
2. Prepare an empty USB memory which is supporting USB Ver.1.0, or memory card
as a input/output device.
3. Insert the device into the corresponding interface at left of display.
Fig. 2 10.4-inch display unit

4. Press the function key .

5. Press the soft key [PARAMETER], then the parameter screen appears.

Fig. 3 Parameter screen


6. Press the MDI switch on the machine operator’s panel or enter state emergency
stop.
7. When a USB memory is used, set “17” to the parameter No.20.
When a memory card is used, set “4” to the parameter No.20.
Note: Before to change the parameter No.20, note the original value.
8. Press the EDIT switch on the machine operator’s panel or enter state emergency
stop.
9. Press the soft key [(OPRT)].
10. Press the continuous menu key until soft key [F OUTPUT] appears. Press
the soft key [F OUTPUT].
11. Press the soft key [EXEC].

12. Press the function key .

13. Press the soft key [SYSTEM], then the system configuration screen appears.

Fig. 4 System configuration screen


14. Press the soft key [(OPRT)].
15. Press the soft key [F OUTPUT].
16. Press the soft key [EXEC].

17. Press the function key .

18. Press the continuous menu key until soft key [ID-INF] appears.
19. Press the soft key [ID-INF], then the CNC ID information screen appears.
Fig. 5 CNC ID information screen
20. Press the soft key [(OPRT)].
21. Press the soft key [F OUTPUT].
22. Press the soft key [EXEC].
23. Confirm that below files are there in USB memory or Memory card.

File name
Parameter CNC-PARA.TXT
System configuration SYS-CONF.TXT
CNC ID information CNCIDNUM.TXT

If the parameter No.20 is changed in the procedure No.7, operate from No.24 to No.26 as
follows,

24. Press the function key .

25. Press the soft key [PARAMETER], then the parameter screen appears.
26. Set the original value to the parameter No.20 as noted.

That’s over the operation.

2 For 15/19-inch display unit


1. Turn on the machine and activate the CNC.
2. Prepare an empty USB memory which is supporting USB Ver.1.0, or memory
card as a input/output device.
3. Insert the device into the corresponding interface at left of display.

Fig. 6 15-inch display unit

4. Press the function key .

5. Press the vertical soft key [PARAMETER], then the parameter screen appears.

Fig. 7 Parameter screen

6. Press the MDI switch on the machine operator’s panel or enter state emergency
stop.
7. When a USB memory is used, set “17” to the parameter No.20.
When a memory card is used, set “4” to the parameter No.20.
Note: Before to change the parameter No.20, note the original value.
8. Press the EDIT switch on the machine operator’s panel or enter state emergency
stop.
9. Press the horizontal soft key [F OUTPUT].
10. Press the horizontal soft key [EXEC].

11. Press the function key .

12. Press the vertical soft key [NEXT PAGE] until vertical soft key [SYSTEM]
appears.
13. Press the vertical soft key [SYSTEM], then the CNC ID information screen
appears.

Fig. 8 System configuration screen

14. Press the horizontal soft key [F OUTPUT].


15. Press the horizontal soft key [EXEC].

16. Press the function key .

17. Press the vertical soft key [NEXT PAGE] until vertical soft key [ID-INF] appears.
18. Press the vertical soft key [ID-INF], then the system configuration screen
appears.
Fig. 9 CNC ID information screen

19. Press the horizontal soft key [F OUTPUT].


20. Press the horizontal soft key [EXEC].
21. Confirm that below files are there in the USB memory or the memory card.

File name
Parameter CNC-PARA.TXT
System configuration SYS-CONF.TXT
CNC ID information CNCIDNUM.TXT

If the parameter No.20 is changed in the procedure No.7, operate as follows,

22. Press the function key .

23. Press the vertical soft key [PARAMETER], then the parameter screen appears.
24. Set the original value to the parameter No.20 as noted.

That’s over the operation.

3 For iHMI screen (Procedure to display a conventional screen)


1. Turn on the machine and activate the CNC.
2. Press <MENU> key displays the Home screen.
<MENU> key

Fig. 10 MDI Keyboard(15 Inch Qwerty Keyboard)


3. Press an icon as “MAINTENANCE DISPLAY”. Otherwise, select it by a cursor
key and press [INPUT] key.

Fig. 11 Home screen MAINTENANCE


DISPLAY
4. Conventional CNC screen is displayed. Continue to operate as section 1 or 2 by
follow as screen size.

4 If any screen doesn’t appear


If any screens are not displayed as section 1 to 3, we expect that an original screen by the
machine tool maker has been displayed. Confirm a manual which is written by the machine
tool builder how to display Fanuc’s screen. When the screen has been display, please try to
operate above section 1 or 2.

©2019 Fanuc Corporation.

You might also like