Nokia NCU/M830B Controller

User Manual, Revision A

Nokia code : CS7190050
Product code : 02300375
The information in this document is subject to change without
notice and describes only the product defined in the introduction
of this documentation. This documentation is intended for the
use of Nokia Networks customers only for the purposes of the
agreement under which the document is submitted, and no part
of it may be used, reproduced, modified or transmitted in any
form or means without the prior written permission of Nokia
Networks. The documentation has been prepared to be used by
professional and properly trained personnel, and the customer
assumes full responsibility when using it. Nokia Networks
welcomes customer comments as part of the process of
continuous development and improvement of the
documentation. The information or statements given in this
documentation concerning the suitability, capacity, or
performance of the mentioned hardware or software products
are given “as is” and all liability arising in connection with such
hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Networks and the
customer. However, Nokia Networks has made all reasonable
efforts to ensure that the instructions contained in the document
are adequate and free of material errors and omissions. Nokia
Networks will, if deemed necessary by Nokia Networks, explain
issues which may not be covered by the document.
Nokia Networks will correct errors in this documentation as soon
as possible. IN NO EVENT WILL NOKIA NETWORKS BE LIABLE FOR
ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES,
INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT
NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS
INTERRUPTION, BUSINESS OPPORTUNITYOR DATA, THAT
MAYARISE FROM THE USE OF THIS DOCUMENTOR THE
INFORMATION IN IT. This documentation and the product it
describes are considered protected by copyrights and other
intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Networks Oy. Nokia is a
registered trademark of Nokia Corporation. Other product names
mentioned in this document may be trademarks of their
respective owners, and they are mentioned for identification
purposes only.
Copyright © Nokia Networks 2020. All rights reserved.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 2

TABLE OF CONTENTS
Safety Precautions .................................................................................. 6
Electrical Safety .................................................................................. 6
Hazardous voltage................................................................................... 6
Tools ........................................................................................................ 6
Thunderstorm ......................................................................................... 6
ESD .......................................................................................................... 7
Short circuit ............................................................................................. 7
Reverse connection................................................................................. 7
Others................................................................................................. 7
Sharp object ............................................................................................ 7
Cable connection..................................................................................... 7
introduction ............................................................................................ 8
Preface ............................................................................................... 8
Overview ............................................................................................ 8
Function Descriptions ........................................................................ 9
Rectifier, Solar Converter, and Converter Control .................................. 9
System Components Monitoring and System Alarms
Generation .............................................................................................. 9
Operating Data Acquisition and Data Logs ........................................... 10
Battery Management ............................................................................ 11
Energy Management ............................................................................. 15
Power Split Feature ............................................................................... 15
Diesel Management Feature................................................................. 16
Supervisory Module (SM Modules) Monitoring ................................... 16
Hybrid Control Function (Supporting Generator, Solar and
Wind Energy Input, and Optimization) ................................................. 16
Maximum Current Limit Function ......................................................... 21
Communications Function .................................................................... 21
Consumption Map Function ................................................................. 22
Operation .............................................................................................. 23
Local Indicators ................................................................................ 23
Using the Local Keypad and Display................................................. 23
Local Menu Navigation Keys and Local Display .................................... 23
Local Display Menus.............................................................................. 24
Using the Web Interface .................................................................. 24
Overview ............................................................................................... 25
Multiple Browsers Supported ............................................................... 25
Web Interface Screens .......................................................................... 25
Passwords and Privilege Levels ........................................................ 25
Multiple Languages Supported ........................................................ 25
Setup Procedures ............................................................................. 25
Logging into the Controller via Web Interface Access ..................... 34
Common Tasks Performed via the Local Keypad and/or Web
Interface ........................................................................................... 36
Procedures ............................................................................................ 36

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 3

 Power Split Feature .......................................................................... 53
Resolving Alarms .............................................................................. 59
Local Display Menus.............................................................................. 97
Overview .......................................................................................... 97
Menus............................................................................................... 97
Main Menu ....................................................................................... 98
Controller Information Menu (accessed from the Main
Menu) ............................................................................................... 99
Alarm Menu ................................................................................... 100
Settings Menu ................................................................................ 101
Start Wizard Sub-Menu (accessed from Settings Menu)............... 107
Input Power Menu ......................................................................... 108
Module Menu................................................................................. 109
DC Menu......................................................................................... 110
Battery Menu ................................................................................. 111
Description of Local Display Menus Programmable Parameters ....... 112
Settings Menu ................................................................................ 112
Maintenance Sub-Menu ..................................................................... 112
Energy Saving Sub-Menu .................................................................... 112
Alarm Settings Sub-Menu ................................................................... 113
Rect Settings Sub-Menu ...................................................................... 113
Batt Settings Sub-Menu ...................................................................... 113
LVD Settings Sub-Menu....................................................................... 116
AC Settings Sub-Menu......................................................................... 116
Sys Settings Sub-Menu ........................................................................ 117
Comm Settings Sub-Menu .................................................................. 117
Other Settings Sub-Menu.................................................................... 118
Rect Ctrl Sub-Menu ............................................................................. 121
Web Interface Screens ........................................................................ 122
Overview of Web Function ............................................................ 122
Homepage ...................................................................................... 122
System Status Information Area .................................................... 124
System Specifications Information Area ........................................ 124
Controller Specifications Information Area ................................... 124
Site Information Area ..................................................................... 124
Alarms Area .................................................................................... 125
System Status Area ........................................................................ 126
Power System Tab ............................................................................... 126
Energy Sources Status Tab .................................................................. 142
Consumption Map Tab........................................................................ 143
User Define Tab................................................................................... 143
Menu Navigation Area ................................................................... 144
Settings Menu ..................................................................................... 145
History Log Menu ................................................................................ 171
System Inventory Menu ...................................................................... 182
Advanced Settings Menu .................................................................... 183

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 4

Accessing the Controller via a Network Management System
(NMS) .................................................................................................. 218
General ........................................................................................... 218
NMS Supported by SNMP Agent .................................................... 218
NMS Supported by SNMP v2............................................................... 218
NMS Supported by SNMP v3............................................................... 218
Parameter Setting in SNMP Manager ................................................. 219
MIB Installation .............................................................................. 220
Installation .......................................................................................... 220
Contents of the Controller’s MIB ........................................................ 220
Accessing the Controller through an NMS ..................................... 220
Apply Administrative Privilege ............................................................ 220
ESR Configure ................................................................................. 220
Replacement Procedures .................................................................... 228
NCU Replacement .......................................................................... 228
NCU Digital Input and Relay Output Connections .............................. 230
NCU Digital Input Connections....................................................... 230
NCU Relay Output Connections ..................................................... 230
IB2 (Controller Interface Board) and EIB (Controller
Extended Interface Board) ............................................................. 230
Specifications ...................................................................................... 232

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 5

SAFETY PRECAUTIONS
To reduce the chance of accident, please read the safety precautions carefully before operation.
The ‘Caution, Notice, Warning, Danger’ in this book do not represent all the safety points to be
observed and are only supplement to various safety points. Therefore, the installation and
operation personnel must be strictly trained and master the correct operations and all the safety
points before operation.
When operating NOKIA products, you must strictly observe the safety rules in the industry, the
general safety points and special safety instructions specified in this book.

Electrical Safety
Hazardous voltage
DANGER! Some components of the outdoor power system carry hazardous voltage in
operation. Direct contact or indirect contact through moist objects with these components
will result in fatal injury.
Observe safety rules in the industry when installing the AC power system. The installation
personnel must be licensed to operate high voltage and AC power.
In operation, the installation personnel are not allowed to wear conductive objects such as
watches, bracelets, bangles, rings.
When water or moisture is found in the cabinet, just turn off the power immediately. In moist
environment, precautions must be taken to keep moisture out of the power system.
Attach ‘Prohibit’ warning label to the switches and buttons that are not permitted to operate
during installation.
DANGER! High voltage operation may cause a fire or electric shock. The connection and
wiring of AC cables must be in compliance with the local rules and regulations. Only those
who are licensed to operate high voltage and AC power can perform high voltage operations.
DANGER! To avoid electric shock hazard of outdoor environment and outdoor equipment,
the non-professionals are prohibited to operate or maintain the outdoor power system.
DANGER! Follow local lockout/tagout procedures to ensure DC branch circuit protection
devices remain de-energized during installation at loads, as required.
Tools
WARNING! In high voltage and AC operation, special tools must be used. No common or self-
carried tools should be used.
Thunderstorm
DANGER! Never operate on high voltage, AC, iron tower or mast in the thunderstorm.

In thunderstorms, a strong electromagnetic field will be generated in the air. Therefore the
equipment should be well earthed in time to avoid damage by lightning strikes.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 6

ESD
NOTE! The static electricity generated by the human body will damage the static sensitive
elements on PCBs, such as large-scale ICs. Before touching any plug-in board, PCB or IC chip,
wear ESD wrist strap to prevent body static from damaging the sensitive components. The
other end of the ESD wrist strap must be well earthed.
Short circuit
DANGER! During operation, never short the positive and negative poles of the DC
distribution unit of the system or the non-grounding pole and the earth. The power system is
constant voltage DC power equipment, and short circuit will result in equipment burning and
endanger human safety.
Reverse connection
WARNING! Never connect reversely live line and neutral line of the AC input cables, or else
the system will be damaged.
Check carefully the polarity of the cable and connection terminal when performing DC live
operations.
As the operation space in the DC distribution unit is tight, please carefully select the operation
space.
Never wear a watch, bracelet, bangle, ring, or other conductive objects during operation.
Use insulated tools.
In live operation, keep the arm, wrist and hand tense, so that when the tool in operation slips, the
movement of the human body and tool is reduced to a minimum.

Others
Sharp object
WARNING! When moving equipment by hand, wear protective gloves to avoid injury by
sharp object.

Cable connection
NOTE! The signal lines should be bound separately from heavy current and high voltage
lines, with binding interval of at least 150mm.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 7

INTRODUCTION
Preface
These instructions describe the functionality of Nokia NCU/M830B Controller (here after uses NCU
for short). Some functionality is dependent on hardware connected to the NCU Your system may
not utilize all the functionality described.
Refer also to the NCU Configuration Drawing (C-drawing) furnished with your system for a list of
factory default settings.

Overview
The NCU performs the following functions:
• Rectifier Control, including an Energy Optimization Mode
• Solar Converter and Converter Control
• System Components Monitoring and System Alarms Generation (including recording alarms
in logs)
• Operating Data Acquisition and Data Logs
• Battery Management
• Energy Management via Energy Optimization Mode
• Power Split Feature
• Diesel Management Feature
• Supervisory Module (SM Modules) Monitoring
• Hybrid Control Function (Supporting Generator, Solar and Wind Energy Input, and
Optimization).
• Maximum Current Limit Function
• Communications Function
• Consumption Map Function
The NCU controls the system automatically via configured parameters.
A User can interface with the NCU locally using the local keypad and LCD display or locally/remotely
using the Web Interface.
The NCU can also be accessed via SNMP (v2 and v3). A machine-to-machine HTTP interface is also
available.
Figure 1 illustrates the various applications that can be used to interface with the NCU.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 8

Figure 1: Interfacing with the NCU

Function Descriptions
Rectifier, Solar Converter, and Converter Control
The NCU controls rectifiers, solar converters, and converters automatically.
NOTE! Solar Mode has to be enabled for NCU control of solar converters (see “Enabling Solar
Mode” on page 43).
System Components Monitoring and System Alarms Generation
The NCU monitors the components comprising the system (such as the rectifiers, solar converters,
converters, and supervisory modules) and generates alarms if a fault condition occurs. The NCU
also maintains an alarm history log.
The available system alarms are programmed with an Alarm Severity Level. Each Alarm Severity
Level has different visual/audible alarm attributes. Available Alarm Severity Levels and their
attributes are listed in Table 1.
The available system alarms can also be mapped to alarm relays (located on controller interface
boards) that can be wired to external alarm circuits.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 9

Table 1: Alarm Severity Levels
Alarm Red Yellow Audible
Severity Levels LED LED Alarm Buzzer
Critical Alarm (CR) ON -- ON
Major Alarm (MJ) ON -- ON
Observation OFF ON OFF
Alarm (OA)
No Alarm (NA) OFF OFF OFF
• Alarm Status Setting: Indicates if the alarm is active or not active,
and the severity level if active. The available alarm status settings
are as follows.
- Critical Alarm: The fault endangers the power systems
continued function.
- Major Alarm: The fault reduces the power systems
functionality.
- Observation Alarm: Special operating condition.
- No Alarm: The alarm is disabled and no alarm is given.
• The alarm indicator turns OFF if the fault(s) that triggered the
alarm clears.
• The audible alarm can be silenced by pressing any key on the NCU
local interface pad. The audible alarm is also silenced if the
fault(s) that triggered the alarm clears.
• An audible alarm cutoff feature can be programmed that silences
the audible alarm after a preset programmable time period. The
audible alarm can also be disabled.
The available system alarms can also be mapped to alarm relays (located on NCU interface boards)
that can be wired to external alarm circuits.
If the system contains a modem, the NCU can be set to call an HLMS (High Level Monitoring
System) via a modem when a critical and/or major alarm is issued and report the alarm to the
HLMS.
Operating Data Acquisition and Data Logs
The NCU acquires and analyses real time data from the system's components such as the rectifiers,
converters, and supervisory modules.
The NCU uses this data to process alarms and also records data in logs. The logs are viewed using
the Web Interface and consists of the following. Logs can be saved in the .html (Web page) or .txt
(text) format.
• Alarm History Log: Records 4000 latest alarms. The Web Interface displays the latest 500
items.
• Battery Test Log: Up to ten (10) battery discharge tests can be recorded.
• Event Log: Records 500 latest events.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 10

 • Data History Log: Records 60000 latest history data. The Web Interface displays the latest
500 items, and you can upload a file with up to the latest 6,000 items in a single date range.
Use multiple date ranges to upload more than 6,000 items.
• System Log: Records 3000 items in run log. The Web Interface displays the latest 500 items.
• Diesel Test Log: Records 500 latest diesel test results.
NOTE! For all logs except the Battery Test Log, once maximum number of log entries is
reached, new entries overwrite the oldest entries.
Battery Management
The NCU provides the following battery management functions.
• Battery Charge Temperature Compensation
• Battery Equalize Charge
• Battery Charge Current Limit
• High and Low Battery Temperature Alarms
• Battery Thermal Runaway Management (BTRM) Feature (Reduces Voltage during a High
Battery Temperature Condition)
• Battery Discharge Test
• Battery Test Logs (maximum ten [10] tests saved)
• Battery LVD (Low Voltage Disconnect)
• Battery Capacity Prediction
• Battery Block and Battery Midpoint Monitoring
• Enhanced Battery Monitoring with SM-BRC
• Thermal Runway Detection and Management
Battery Charge Temperature Compensation
The NCU can be programmed to automatically increase or decrease system output voltage to
maintain battery float current as battery temperature decreases or increases, respectively. Battery
life can be extended when an optimum charge voltage to the battery with respect to temperature is
maintained. Temperature is monitored by a sensor mounted on the battery. See your power
system documentation for temperature sensor information. You can also set high and low
compensation temperature alarms.
Functional Description (See Figure 2):
Battery charge temperature compensation adds a correction term, related to the temperature of
the batteries, to the nominal value of the system voltage. The degree of regulation (TempComp
Coeff), expressed in mV/°C/battery string, can be set per battery manufacturer recommendations.
To protect batteries and voltage-sensitive loads, compensation is automatically limited to a
maximum of two volts (48V systems) or one volt (24 volt systems) above or below the nominal
output level (float setting).
Temperature compensation is automatically disabled if communication between the controller and
all rectifiers is lost, a DC over or under voltage alarm activates, a low voltage disconnection occurs,
manual mode is entered, or the system enters the equalize or test modes.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 11

Figure 2: Temperature Compensated Voltage Control

V TempComp Coeff
setting (mV/°C).

Upper voltage level where temperature compensation

Vhigh clamps the voltage. Limited to the TEMP COMP MAX V
1V Max (24V System) setting.
2V Max (48V System)
Vnom Nominal voltage (voltage at nominal temperature).
1V Max (24V System)
2V Max (48V System)
Lower voltage level where temperature compensation
V low clamps the voltage. Limited to the TEMP COMP MIN V
setting.

Tnom
Nominal temperature (no temperature compensation is done at this temperature).
Tnom
This is the Temp Comp setting.

Battery Equalize Charge and Battery Charge Current Limit

The NCU can increase system output voltage for equalizing the charge on all battery cells of a
conventional flooded cell battery, or for recharging the battery following a commercial power
failure.
The charging function can be initiated cyclically (scheduled), automatically, or manually.
Refer to the battery manufacturer's instructions for equalize charging instructions.
Functional Description (See Figure 3):
• Start of Charging: When the battery charge current exceeds a preset value for three (3)
minutes or if the calculated battery capacity has decreased to a preset value (after a
commercial AC failure, for example), the charging function of the NCU is activated. A
charging signal is sent from the NCU to the rectifiers to increase the voltage up to the battery
charging level V equalize .
• Battery Current Limitation: After a commercial AC failure or when some battery cells are
permanently damaged, the current to the batteries can be quite extensive. To avoid
overheating or further damages to the battery, the NCU limits the battery current to a preset
level by limiting the charging voltage of the rectifiers. Should the battery current still exceed
a higher preset value, an alarm is issued.
• End of Charging: When the charging current drops below a preset value, a defined
prolonged charging time is started before the charging is stopped and the voltage of the
rectifiers return to the float charging level (V nom ). For safety, there is an equalized charging
limit time that stops the charging after a preset time.

Figure 3: Voltage Characteristics on Commercial AC Failure and Automatic Equalize Charging

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 12

High and Low Battery Temperature Alarms
The NCU can monitor battery temperature via a temperature sensor mounted on a battery cell.
Values for high battery temperature and low battery temperature alarms can then be programmed
into the NCU.
Battery Thermal Runaway Management (BTRM) Feature
The Battery Thermal Runaway Management (BTRM) feature reduces voltage during a high battery
temperature condition.
You can designate a temperature sensor as the BTRM sensor. The BTRM sensor has High 2 and
High 1 BTRM temperature alarm limits. If battery temperature exceeds the “BTRM Temp High 2”
setting, system voltage is lowered to the BTRM voltage setting. This feature can also be disabled.
Battery Discharge Test and Battery Test Logs
The NCU can perform battery discharge tests to check the condition of the battery(s). There are
three (3) types of battery discharge tests:
• Battery Test without Constant Current
• Battery Test with Constant Current
• Short Time Test (requires two battery shunts)
A User can manually start a battery discharge test or program the NCU to automatically start
battery discharge tests at scheduled intervals. Twelve (12) Constant Current Tests can be
scheduled by the month-day-hour. A Short Time Test can be scheduled to be performed every 1-
365 days. During a battery discharge test, the NCU controls the rectifiers output to place the entire
load or partial load on the batteries. The NCU monitors the discharge of the battery and saves the
results in a battery test log. The NCU stores ten (10) battery discharge tests.
Functional Description:
For manual battery discharge tests as well as for scheduled battery discharge tests, the following
parameters must be set: End Test Voltage, End Test Time, and End Test Capacity. See Figure 4.

Figure 4: Battery Test Diagram

Battery Discharge Test Sequence:

• For a Constant Current Test, the output voltage of the rectifiers is reduced so that the
batteries supply the preset Constant Current Test Current to the load.
• If Constant Current is disabled, then the current being delivered by the batteries will be
dependent on the load.
• For a Short Time Test, the output voltage of the rectifiers is reduced so that only the
batteries power the load. If the batteries fail, the rectifiers power the load.
• The battery test continues until one of the following occurs:
- The preset End Test Time, see Figure 4, expires. The battery has passed the test.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 13

 - The battery capacity drops below the preset End Test Capacity. The battery has passed
the test.
- The battery voltage drops below the preset End Test Voltage (Vend) (see Figure 4). The
battery has not passed the test and the test is interrupted. A bad battery alarm is
activated.
- If a critical alarm occurs during the test or there’s not enough load, the battery test is
aborted. In such cases a “Battery Test Fail” alarm will be activated (indicating the test
couldn’t be done). This alarm is different from the “Bad Battery” alarm (meaning the test
was completed but the battery didn’t pass it).
• A battery test alarm is active during a battery discharge test.
• If the battery has not passed the test, a bad battery alarm is activated.
• After the battery discharge test, the output voltage of the rectifiers increases so that the
rectifiers supply the system and charge the batteries.
NOTE! A procedure for performing a manual battery discharge test is provided on page 50.

Battery LVD (Low Voltage Disconnect)

To prevent serious damage to the batteries during a commercial AC power failure, the batteries can
be disconnected by voltage or time control.
The batteries are reconnected automatically when commercial AC power is restored and a
predetermined DC voltage level is reached.
Battery Capacity Prediction
The NCU can predict battery capacity. When a battery is connected to the system at initial setup or
increasing the number of batteries, you need to update the Battery Ah rating. After doing this and
making sure the battery is fully charged you need to reset the battery capacity used percentage by
performing the “Reset Battery Capacity” command to tell the NCU that the batteries are 100%
charged. From this point forward the NCU will keep track of the battery current and time to predict
the battery capacity used.
Battery Block and Battery Midpoint Monitoring
The NCU can monitor battery blocks (12 V blocks) or midpoint battery voltage of battery strings
connected to the EIB (Controller Extended Interface Board) assembly. An alarm is issued when
either battery block voltage or battery midpoint voltage is abnormal.
Enhanced Battery Monitoring with SM-BRC
When connected to an SM-BRC, the NCU provides enhanced battery monitoring.
Thermal Runaway Detection and Management
Functional Description:
The system uses several control mechanisms to avoid thermal runaway.
• During a short high rate discharge, the batteries will normally get hot. The NCU takes this
into consideration. After completion of the discharge duty, the batteries are recharged with
a limited current to avoid heating the batteries any further.
• The temperature of the batteries can be monitored, and the NCU sets the charge voltage
appropriately, as previously described under “Battery Charge Temperature Compensation”
on page 11.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 14

 • In addition to battery temperature compensation, if battery temperature rises above a set
temperature limit, the system stops battery charging completely by lowering the output
voltage to the “BTRM Voltage” setting. This allows the batteries to cool down. The system
also provides alarm notification of this occurrence. Power supplied to customer equipment
is not interrupted. See “Setting Battery Thermal Runaway Management (BTRM) Feature” on
page 45 for programming.
• The battery LVD circuits can be programmed to open (disconnect) if a high temperature
event occurs (HTD-High Temperature Disconnect). The contactor(s) open when battery
temperature rises above a programmable value and close again when battery temperature
falls below another programmable value. See “LVD Tab Programmable Parameter
Descriptions” on page 164 for programming.
Energy Management
Energy Management consists of an Energy Optimization Mode.
Energy Optimization Mode
The NCU provides an Energy Optimization Mode (ECO) function. Energy Optimization permits an
installation to only operate rectifiers as needed to maintain the load and keep batteries in a fully
charged condition. As load increases, Energy Optimization turns on additional rectifiers as needed
to maintain the load. As load decreases, Energy Optimization places rectifiers in standby to
conserve energy usage. Rectifiers which are always operating to maintain any load requirements
are cycled through the group of rectifiers controlled by this feature to provide uniform operating
times for each rectifier.
ALERT! The Energy Optimization Mode should NOT be used in systems that operate without
batteries.

Power Split Feature

The Power Split feature allows you to connect the power system controlled via the NCU to an
existing DC power system instead of extending or completely replacing the existing DC power
system.
The power system controlled via the NCU functions as slave system to share load (split output) with
the existing system (master system) that requires expansion. The NCU does not require
communication with the master system’s controller.
The Power Split feature provides for the sharing of total load in a controlled manner between the
paralleled power systems.
When Power Split is programmed, the NCU adjusts rectifier output voltage per load demands to
ensure proper sharing between the slave and master power systems. See Figure 5.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 15

Figure 5: Power Split Feature

Diesel Management Feature

The Diesel Management feature is available when an SM-AC supervisory module is connected to
the NCU. The Diesel Management feature consists of a Diesel Test. The Diesel Test can be
performed at specific intervals or a User can manually start the Diesel Test. The NCU records the
test results.
Supervisory Module (SM Modules) Monitoring
Various devices (supervisory modules) can be connected to the NCU to extend its monitoring
capabilities.
Hybrid Control Function (Supporting Generator, Solar and Wind Energy Input, and Optimization)
Hybrid Control is designed for use in new installations or as an upgrade of existing sites powered by
a diesel generator(s) when grid power is not available. The Hybrid control is also applicable to sites
with highly unreliable or frequently unavailable grid power connection. The primary power source
is still considered to be the diesel generator(s). Since grid power is always given priority, the
primary power source is still considered to be the grid power.
NOTE! The Hybrid Control function requires a specific configuration. Hybrid Control menus
will not normally be displayed unless your NCU has been configured by NOKIA for this
function. Contact NOKIA for a Hybrid Control configuration.
General
Hybrid Control allows the option of selecting one of the following: Fixed Daily Time based
operation or Capacity Discharge based operation.
Fixed Daily Time based operation is intended to be used with a combination of AC powered active
cooling (air conditioners) and DC powered cooling (heat exchangers, etc.). The cycle period is
synchronized to the 24hrs day-night cycle. It makes optimum use of the different temperature
conditions during the day and the night in order to facilitate Hybrid fuel saving operation.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 16

Capacity Discharge based operation is intended for sites utilizing only DC powered cooling (heat
exchangers, etc.). The cycle period is determined by User selectable depth of discharge (DOD) of
the batteries per cycle, and associated recharge time. It provides optimum Hybrid fuel saving
operation.
Operation from Grid Power is performed with both Fixed Daily Time and Capacity Discharge modes
of operation. Grid power is always given priority when available.
As the two types of control are specific to the hardware configuration of the site, the Fixed Daily
Time or Capacity Discharge is a User selectable option on installation.
Hybrid Operation
Generator Control: A potential free relay contact output from the NCU interface board controls the
start and stop of the diesel generator. The signal will be generated by the NCU and operates
according to the Hybrid software mode of operation. The default control logic (User selectable) is
as follows:
• Energized Output Relay - Generator OFF
• De-energized Output Relay – Generator ON
This is a fail-safe logic to ensure generator operation in all cases where power or control to the
relays is lost.
In addition, the type of signal to the Generator can be selected as N/O (Normally Open) or N/C
(Normally Closed) by selecting the relevant output pins of the control relay.
Number of Generator Control Outputs: The NCU Hybrid software can control one or two
generators. Each generator control is designated as DG1 or DG2 output. The User can select DG1,
or DG2, or DG1 and DG2. When both are selected they will be alternatively used (two generators
operation).
Diesel Fail Alarm: A diesel fail alarm will be generated if the Diesel Generator ON signal fails to
bring the generator to operation and provide the system with AC power. Alarm will be triggered
after 60 seconds (default value, settable) from ON signal. If two generator operation is selected,
the second Diesel Generator ON signal will be activated simultaneously with the Diesel Fail alarm.
Battery Fuse Trip Alarm: In the event of a Battery Fuse trip condition, an alarm will be generated.
Under Voltage Alarms:
• Under Voltage Alarm 1: If voltage decreases below the Under Voltage Alarm 1 setting, an
alarm is raised.
• Under Voltage Alarm 2: If voltage decreases below the Under Voltage Alarm 2 setting, the
Diesel Generator is started and an alarm is raised.
LVD 1: Normal loads are disconnected.
LVD 2: Priority loads are disconnected.
Charge Voltage: Refer to Figure 6.
Equalize Charge: The battery will be recharged at the equalize voltage. This is the voltage set in the
initial phase of battery recharge. See Figure 6.
As the voltage limit is reached, the charge current is gradually reduced – this effect is known as
current tail. When the current tail falls below a threshold level, additional equalize charge time is
added and then the recharge ends.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 17

The equalize charge current tail threshold is settable from 0.002 to 0.02. Default setting is 0.01 (1 A
per 100 Ah). The additional equalize charge time is settable from 1 hour to 24 hours (settable in
minutes from 0 to 1440), default setting is 3 hours. The duration of the equalize charge is the time
from the start of the recharge to the end of the additional time. (Maximum charge time,
determined from the time charge starts, is settable in the range of 1 hour to 48 hours, default
setting is 18 hours).
The end of recharge is determined by a three (3) step approach:
• Step1 - calculated battery capacity exceeds 90%. Calculation is performed by measurement
of battery current and time, in Ah.
• Step 2 - charge current tail threshold is reached.
• Step 3 - additional charge time is completed.
Float Charge: Default float voltage is 54.0 V at 20°C with a temperature compensation of 72 mV per
°C.
If battery temperature exceeds 38°C (should be Very High Temperature alarm), the charge voltage
is reduced to 48 V to reduce gassing and prevent thermal runaway. The same is applicable as well
for equalizing charge.
Equalizing Charge Cycle: As the cyclic use does not ensure complete battery recharge after every
cycle, an equalizing charge cycle is added. The equalizing cycle is settable for every 2 to 365 days
intervals, default setting is 100 days. Equalizing charge time is 12 hours independent of discharge
time setting. Equalizing charge is performed at equalize voltage until end of additional equalize
time and thereafter at float voltage for the remaining time. Also see Figure 6.
Equalize charge independently settable 0-1440 min (already set in equalize charge).

Figure 6: Charge Voltage

Early Termination of the Discharge Periods

During discharge, over temperature and under voltage conditions will interrupt the discharge and
change the operation to charge with the Diesel Generator ON.
Over Temperature: The diesel generator will start and run for a period before it is stopped again.
The run time is User selectable in the range 30 to 120 minutes, default setting is 60 minutes.
Temperature is referenced to cabinet/shelter ambient temperature sensor connected to controller,

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 18

not battery temperature. Over temperature start can be disabled completely from the Settings
menu.
Under Voltage: The under voltage start is triggered by under voltage alarm 2 voltage settings.
The diesel generator will start and run until the normal recharge cycle is due to finish depending on
selected mode of operation.
Under Voltage with Fixed Daily Time: If the normal recharge cycle is from 7am until 7pm and under
voltage has started the Diesel Generator at 5:30am, the effective recharge will be from 5:30am
until 7pm.
Under Voltage with Capacity Discharge: If this mode is selected, the recharge will terminate.
Operation with Grid Power
Grid power is always used when available. If grid power becomes available during battery
discharge, the discharge cycle is terminated and recharge cycle is initiated. If grid power becomes
available during diesel generator operation, the diesel generator is switched OFF and operations
continue on grid power.
Battery Recharge with Grid Power: Battery recharge with grid power can start from the beginning
(when grid power becomes available during battery discharge) or can continue from diesel
generator recharge, depending on the timing. In both cases, the recharge process will follow the
recharge profile shown in Figure 6. If battery becomes fully recharged and grid power is still
present, the operations will continue to be powered from grid and no battery discharge will be
initiated for the duration of grid availability. In this case, battery voltage will revert back to Float
voltage.
Battery Discharge after Grid Failure: At the point of grid power failure, the battery capacity is
unknown as these events occur in random manner. For the purpose of maximizing the use of grid
power and in anticipation of grid power becoming available again, the Hybrid operation will
continue with battery discharge cycle. Discharge will continue until:
• The preset discharge time elapses (Fixed Daily Time)
• The preset DOD is reached (Capacity Discharge)
In both cases, the discharge can be terminated earlier as described in “Early Termination of the
Discharge Periods” on page 18.
Relay Assignment – when in Hybrid Mode
Relay 1: Generator Alarm.
No Generator Voltage Alarm. No AC supply, 60 sec delay.
Relay 2: Battery Alarms.
Logic alarm generated from: under voltage 1, under voltage 2, LVD1, LVD2, battery high temp,
battery very high temp, overvoltage 1, overvoltage 2, battery temp sensor fail, battery fuse alarms
and high load alarm.
Relay 3: Rectifier Alarms.
Logic alarm generated from: multiple rectifier fail, rectifier fail, rectifier fan failure, rectifier HVSD,
rectifier AC failure and rectifier not responding.
Relay 4: System Alarms.
Logic alarm generated from: load fuse alarms, high ambient temperature, ambient temp sensor
fails; smoke detected, and water detection.
Relay 5: Generator Run at High Temp.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 19

Output to intelligent cooling devices linked to AC supply (DG run).
Relay 6: Intruder Alarm.
Alarm triggered by dry contact door/motion sensor.
Relay 7: Diesel 1 in Operation.
Output to DG1 on site. DG is set on for the duration of the signal.
Relay 8: Diesel 2 in operation.
Output to DG2 on site. DG is set on for the duration of the signal.
Fixed Daily
In this mode of operation, the total duration of a complete cycle is 24hrs. This duration is necessary
as the operation is synchronized with day-night temperature pattern. When an extended recharge
cycle is required, its termination will still follow the 24hrs schedule.
Cycle Duration: A complete cycle consists of discharge and charge periods during the combined
total of 24hrs. The discharge period starts at 7pm. It is then followed by recharge period (Diesel
Generator ON) for the remainder of the 24hrs. The discharge time is User selectable in the range
1hrs to 22hrs, default setting is 12hrs.
Discharge: The discharge start time and duration are settable. Discharge period starts at 7pm. The
discharge time is User selectable in the range 1hours to 22hours, default setting is 12 hours.
Recharge: Recharge period (Diesel Generator ON) follows after discharge for the remainder of the
24hrs. Recharge is performed at equalize voltage until added equalize time elapses and at float
voltage for the remaining charge time.
High Load Alarm: In order to identify conditions where the load requirements are exceeding the
dimensioning of the Hybrid site, an alarm will be generated. The alarm will be triggered when the
maximum capacity per discharge cycle is exceeded. The threshold value will be set as default to
40% of battery capacity. It will require capacity measurement per cycle. The alarm will be set once
the high load threshold value is reached and is reset at the beginning of the next discharge period.
This alarm will help the User identify the root cause of the under-voltage condition: high demand
load, the loss of capacity due to battery aging, or insufficient charge capacity.
Capacity Discharge
The cycle period is determined by User selectable capacity discharge of the batteries and associated
recharge times. The cycle repeats continuously. It does not follow a 24hrs pattern.
Capacity Discharge and Recharge: The battery discharge period is determined by the percentage of
the nominal battery capacity [Ah] that will be discharged per cycle.
The depth of discharge [DOD] per cycle is User selectable in the range 20% to 80%. Default setting
is 60%. The value is set as battery capacity at the end of each discharge period. Therefore, if a 60%
discharge is chosen, the discharge value is set to 40%.
The time to recharge to full battery capacity depends on battery capacity at the start of the charge
cycle and the available recharge current.
When the additional charge time has been reached; the generator will be stopped, the recharge
cycle will end, and discharge cycle will be initiated.
For practical purposes, the battery capacity at the end of every recharge period is set to 100% as
long as Step1, Step 2, and Step 3 have elapsed.
If end of charge is not reached within the set maximum hours, the recharge will be terminated and
discharge cycle will be initiated.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 20

Maximum Current Limit Function
The current available from the rectifiers can be limited (in AMPS) from 10% to 121% of combined
rectifier capacity. The factory setting is 121% unless otherwise specified. The current available
from the converters can be programmed (in AMPS) from 50% to 116% of combined converter
capacity. The factory setting is 116% unless otherwise specified. Refer to the NCU Configuration
Drawing (C–drawing) supplied with your system documentation for your system’s settings.
If a rectifier or converter is added, the respective current limit point in amps will automatically
increase to maintain the same percentage. For example, if the current limit was set to 100% of
combined capacity and a rectifier/converter is added, the new current limit setpoint will be 100% of
the combined capacity including the new rectifier/converter.
If a rectifier or converter is removed from the system (and the Rect Comm Fail or Conv Comm Fail
alarm is reset), the respective current limit point will remain unchanged unless the capacity of the
remaining rectifiers or converters is not sufficient to maintain this current limit point. If that
happens, the current limit point will automatically decrease to the maximum (121% of the
remaining rectifiers or 116% of the remaining converters).
When setting total rectifier or total converter current limit, the set point to each unit is the total set
point divided by the number of units. For example, if the system contains five rectifiers and the
current limit is set to 150 amps then each rectifier has a current limit set point of 30 amps. If one or
more rectifiers or converters are removed or fail, it will take several seconds for the individual set
points to the remaining rectifiers or converters to be reset. In the example given, if one rectifier is
removed the current limit set point will drop to 120 amps (30 amps times four remaining rectifiers)
until the controller can send updated set points to the remaining rectifiers. This takes a couple
communication cycles (several seconds) after which each rectifier would have a new set point of
37.5 amps for a total of 150 amps. The total current limit of the rectifiers and converters should
not be set such that the loss of the redundant rectifiers or converters will cause this temporary set
point to drop below the actual maximum expected load. If batteries are used on the rectifier
output, the batteries should support the load until the current limit set points can be re-established
due to loss of a rectifier.
Communications Function
The NCU is able to communicate with different equipment or connect to different equipment for
communication. See Figure 7.
a) 10M/100M Ethernet Port: The NCU can communicate with a supervisory computer or
other devices through its 10M/100M Ethernet port. The communication cable shall be a
shielded cable. The Ethernet port is located on the front panel of the NCU. This port
supports Dynamic Host Configuration Protocol (DHCP) function.
NOTE! Some systems may have an IB4 board with a second Ethernet port. The IB4 board is
connected to the NCU’s backplane connector (USB) via a factory provided cable. Refer to your
system’s documentation for location of the IB4 board (if furnished).
b) IB2 (Interface Board) and EIB (Extended Interface Board): Some systems may have an
IB2 (Interface Board) and/or EIB (Extended Interface Board) connected to the NCU. Each
IB2 board provides eight (8) dry relay outputs. Each EIB board provides five (5) dry relay
outputs. Every relay output has a set of NC (normally close) and NO (normally open)
contacts.
The relay outputs can be connected to customer external alarm circuits. Each relay output
can be configured to change state when one or more alarm events occur.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 21

 The relay outputs can also be connected to customer external equipment, so that the relay
output can control or interface with the customer external equipment.
c) IB4 (Interface Board 4): Some systems may have an IB4 board. The IB4 board is a USB to
LAN converter for the NCU, which includes a USB and an Ethernet port. The IB4 board is
connected to the NCU’s backplane connector (USB) via a factory provided cable. Refer
to your system’s documentation for location of the IB4 board (if furnished).
d) RS-485 Port: The NCU can communicate with an SM-AC, SM-Bat, or SMIO through the
RS-485 port. The RS-485 port uses the parameters 19200, n, 8, 1.
e) Modbus Protocol: The NCU can communicate with an AC Meter using the Modbus
protocol.
f) Modem (if available): When the NCU communicates through a modem, it uses
PSTN/USB for long-distance monitoring. Power supply cables and communication cables
will be prepared for the communication through the modem. Modem communication
mode uses the EEM Protocol. Refer to your system’s documentation.

Figure 7: The Controller Perspective

Consumption Map Function

The NCU controller has a consumption map function accessible via the Web pages. A User can
designate a power system’s output branch circuit (connected to a customer load) to be monitored
for consumption. Customer load consumption parameters for this output branch circuit are
displayed on the consumption map Web page.
Refer to “Web Interface Screens” on page 122.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 22

OPERATION
Local Indicators
Location and Identification: Refer to Figure 8.
Description: There are three (3) indicators located on the NCU’s front panel. Refer to Table 2 for
the function of the indicators.

Figure 8: Local Indicators and Menu Navigation Keys Locations

Table 2: Local Indicators

Indicator Normal State Fault State Fault Cause

Status On Off No input power to the NCU.

(Green)

Observation The system has one or more

Alarm Off On active observation alarms. Alarm
(Yellow) conditions are programmable.

The system has one or more

Major or active Major or Critical alarms.
Critical Alarm Off On Alarm conditions are
(Red) programmable.

Using the Local Keypad and Display

See also “Passwords and Privilege Levels” on page 25.
Local Menu Navigation Keys and Local Display
Location and Identification: Refer to Figure 8.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 23

Description: There are four (4) menu navigation keys and a local display located on the NCU’s front
panel. Refer to Table 3 for the function of the menu navigation keys.
NOTE! When the local display is lit, if no button is pushed for eight (8) minutes, the backlight
of the local display extinguishes and the NCU returns to the Main Menu. Press any key to re-
activate the local display.

Table 3: Local Menu Navigation Keys

Key Symbol Key Name Function

Press this key to go back to a previous

ESC Escape menu or to cancel setting a
parameter. Press ESC and ENT together
to reset the NCU, then press
Press this key to go forward to the ENT to accept or ESC to
next menu, to select a parameter to cancel.
ENT Enter edit, or to validate a parameter setting
change.

 Up Arrow Press the up or down arrow keys to

scroll through the menus or to change --
 Down Arrow the value of a parameter.

Press any key to silence an audible alarm.

Local Display Menus
Refer to “Local Display Menus” on page 97.
Navigating the Menus
To Select a Sub-Menu:
Press the UP and DOWN keys to highlight the desired sub-menu.
Press the ENT key to enter the selected sub-menu.
To Select a User and Enter a Password:
To select a User, use the UP and DOWN keys to move the cursor to the Select User field. Press ENT.
Use the UP and DOWN keys to select a User previously programmed into the NCU. Press ENT to
select the User. Note that only Users programmed into the NCU are shown. Users are
programmed via the Web Interface.
To enter a password, use the UP and DOWN keys to move the cursor to the Enter Password field.
Press ENT. Use the UP and DOWN keys to choose a character. Press ENT to accept and move to
the next character. Continue this process until all characters are entered. Press ENT again to
accept the password.
To Change a Parameter:
Press the UP and DOWN keys to move up and down the list of parameters.
Press ENT to select the parameter.
Press the UP and DOWN keys to change the parameter.
Press ENT to make the change. Press ESC to cancel the change.

Using the Web Interface

See also “Passwords and Privilege Levels” on page 25.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 24

 NOTE! The NCU supports a 10/100M Ethernet connection.

Overview
Via the Web Interface, a User (with proper access level) can:
• View real-time operating information (rectifiers, converters, solar converters, AC, DC,
batteries, etc.).
• View and download information recorded in logs.
• Send control commands.
• Set programmable parameters.
• Download and upload the “SettingParam.tar” file.
• Download firmware to the controller.
Multiple Browsers Supported
Multiple browsers are supported in the Web Interface. The User can use Internet Explorer,
Chrome, Safari, or Firefox.
Web Interface Screens
Refer to “Web Interface Screens” on page 122.

Passwords and Privilege Levels

Local Keypad and Display
Anyone can browse the NCU via the local keypad and display. A User Name and Password is
required to change settings. User Names and associated passwords are programmed into the NCU
via the Web Interface. To change settings locally, a User Name and Password for a User with an
access level of Level B (Operator) or higher is required. See “Users Tab” on page 184. Once a
password is entered locally, it remains in effect for a preset time period to allow navigating
between menus without re-entering the password.
Web Interface
Web interface access always requires a User name and password to be entered to gain access.
Web Interface User Privilege Levels: Users are programmed with a “privilege level” (see Table 5 on
page 186). Each privilege level gives a User Web access to specific menus, as shown in Table 5 on
page 186. A User has access to his/her level menus, plus all menus of the lesser privilege levels.

Multiple Languages Supported

Multiple languages are supported in the Local Interface and Web Interface. Refer to “Language
Tab” on page 191.

Setup Procedures
Setting IPv4 Communications Parameters (if controller not set as DHCP)
The controller’s IPv4 parameters (IP, subnet mask, and gateway addresses) must be set to match
your company’s network settings. The default settings for these parameters are shown below.
• IP Address: 192.168.100.100
• Subnet Mask Address: 255.255.255.0

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 25

 • Gateway Address: 192.168.100.1
Local Menu Navigation:
Main Menu / Settings Icon / Comm Settings / enter parameters.
Web Menu Navigation:
Advance Settings Menu / Ethernet Tab / enter parameters.

Setting IPv6 Communications Parameters (if controller not set as DHCPv6)

The controller’s IPv6 parameters (IPv6 address, IPv6 prefix, and IPv6 gateway address) must be set
to match your company’s network settings. The default settings for these parameters are shown
below.
• Link-Local Address: fe80:209:f5ff:fe09:1002/64
• IPv6 Address: 20fa:fffd:fffc:fffb:fffa:fff9:fff8:fff7
• IPv6 Prefix: 0
• IPv6 Gateway: 20fa:1:fffe:ffff:fffe:fffd:ffff:fffe
Local Menu Navigation:
Main Menu / Settings Icon / Comm Settings / enter parameters.
Web Menu Navigation:
Advance Settings Menu / Ethernet Tab / enter parameters.

Setting for DHCP and DHCPv6

The DHCP and DHCPv6 functions allow the controller to acquire an IP address automatically. This
function can only be enabled or disabled via the local display and keypad. If this function is enabled
and the acquisition of an IP address fails, an alarm is generated. If the acquisition of an IP address is
successful, you need to record the IP address automatically acquired by the controller to access the
controller via the Web Interface. This IP address is displayed on the main system info screen (Main
Menu / ESC) in the IP Address field or in the local display menu (Main Menu / Settings Icon / Comm
Settings) in the IP Address field below the DHCP setting.
Local Menu Navigation:
Main Menu / Settings Icon / Comm Settings / DHCP (set to enabled) (can also view acquired IP
address).
Main Menu / ESC (to view acquired IP address).
Web Menu Navigation:
None.
Connecting the Controller to your Local Area Network (LAN) when the System is NOT Equipped with
an IB4 Board
An Ethernet port is located on the front panel of the NCU. This port supports Dynamic Host
Configuration Protocol (DHCP) function.
If your system does not have an IB4 board, connect the Local Area Network (LAN) to the NCU’s
front panel port. This port can be assigned an IP address or can be set for DHCP. If set for DHCP, it
will get its IP address from a DHCP server on the network. Refer to “Setting IPv4 Communications
Parameters (if controller not set as DHCP)” on page 25 or “Setting IPv6 Communications

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 26

Parameters (if controller not set as DHCPv6)” on page 26 to set the port parameters;
or,
“Setting for DHCP and DHCPv6” on page 26 to set the port as DHCP or DHCPv6.

Connecting the Controller to your Local Area Network (LAN) when the System IS Equipped with an
IB4 Board
NOTE! Your system may be furnished with an IB4 board. The IB4 board provides a second
Ethernet port. The Ethernet port located on the NCU Controller’s front panel can ONLY be
used to connect a computer directly to the NCU. The Ethernet port located on the IB4 board
can be used to connect the NCU to your Local Area Network (LAN). Refer to your system’s
documentation for location of the IB4 board (if furnished).
NOTE! If your system has an IB4 board, DO NOT connect your Local Area Network (LAN) to
the NCU front Ethernet port.
Some systems may have an IB4 board with a second Ethernet port. This port supports Dynamic
Host Configuration Protocol (DHCP) function. Refer to your system’s documentation for location of
the IB4 board (if furnished).
If your system has an IB4 board, connect the Local Area Network (LAN) to the IB4 board port. The
IB4 board port can be assigned an IP address or can be set for DHCP. If it is set for DHCP, it will get
its IP address from a DHCP server on the network. Refer to “Setting IPv4 Communications
Parameters (if controller not set as DHCP)” on page 25 or “Setting IPv6 Communications
Parameters (if controller not set as DHCPv6)” on page 26 to set the port parameters;
or,
“Setting for DHCP and DHCPv6” on page 26 to set the port as DHCP or DHCPv6.

Connecting a Local Computer Directly to the Controller when the System is NOT Equipped with an
IB4 Board
An Ethernet port is located on the front panel of the NCU. This port supports Dynamic Host
Configuration Protocol (DHCP) function.
If your system does not have an IB4 board, perform the following procedure.
Procedure
1. Before connecting your computer directly to the controller’s Ethernet port, use the
following procedure to record your computer’s network settings (so they can be
returned to these values when done) and then change these settings in your
computer to match the communications settings programmed in the controller.
NOTE! Windows 7 operating system is used in this procedure, other operating systems are
similar.

a) Record your computer’s network settings by launching Control Panel in your computer.
Navigate through Network and Sharing Center  Local Area Connection  Properties 
Internet Protocol Version 4 (TCP/IPV4)  Properties.
b) Record whether the "Obtain an IP address automatically" or "Use the following IP
address" button is selected. If "Use the following IP address" button is selected, also
record the following:

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 27

 IP Address:
Subnet Mask:
Default Gateway:
c) Record your controller’s network settings by navigating the controller’s local display
panel to Main Menu / Settings Icon / Comm Settings. Record the following controller’s IP
parameters. If these parameters were not changed, they should be at the default values
as shown in the example section below.
IPv4
IP Address:
Subnet Mask:
Default Gateway:
Example:
IP Address: 192.168.100.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.100.1
IPv6
IPv6 Address:
IPv6 Prefix:
IPv6 Gateway:
Example:
IPv6 Address: 20fa:fffd:fffc:fffb:fffa:fff9:fff8:fff7
IPv6 Prefix: 0
IPv6 Gateway: 20fa:1:fffe:ffff:fffe:fffd:ffff:fffe
d) Change your local computer’s network settings using the information you acquired in the
above step, except that the last part of the IP address needs to be replaced with any
different number.
IPv4
IP Address:
Subnet Mask:
Default Gateway:
Example:
IP Address: 192.168.100.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.100.1
IPv6
IPv6 Address:
IPv6 Prefix:
IPv6 Gateway:
Example:
IPv6 Address: 20fa:fffd:fffc:fffb:fffa:fff9:fff8:fff7
IPv6 Prefix: 0
IPv6 Gateway: 20fa:1:fffe:ffff:fffe:fffd:ffff:fffe

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 28

 e) Select OK. Note that you may have to reboot your local computer for the settings to take
effect. Follow any instruction you see on the screen.
2. Connect your computer directly to the controller’s Ethernet port (RJ-45 jack located
on the front of the controller). See Figure 8. The NCU’s front panel port is configured
with an IP address. Default is 192.168.1.2. This is the address you will type into your
Web browser to access the NCU’s Web Interface. You will also have to set the
properties on your computer (refer to the previous procedure in step 1).
3. When finished, disconnect your computer from the NCU and, if necessary, reset your
computer network settings as recorded in step 1.

Connecting a Local Computer Directly to the Controller when the System IS Equipped with an IB4
Board
NOTE! Your system may be furnished with an IB4 board. The IB4 board provides a second
Ethernet port. The Ethernet port located on the NCU Controller’s front panel can ONLY be
used to connect a computer directly to the NCU. The Ethernet port located on the IB4 board
can be used to connect the NCU to your Local Area Network (LAN). Refer to your system’s
documentation for location of the IB4 board (if furnished).
An Ethernet port is located on the front panel of the NCU. This port supports Dynamic Host
Configuration Protocol (DHCP) function.
Some systems may have an IB4 board with a second Ethernet port. Refer to your system’s
documentation for location of the IB4 board (if furnished).
If your system has an IB4 board, perform the following procedure.
Procedure
1. Connect your computer directly to the controller’s Ethernet port (RJ-45 jack located
on the front of the controller). See Figure 8. The NCU’s front panel port will have the
following IPv4 Address: 192.168.100.100. Enter the address 192.168.100.100 in your
Web browser to access the NCU’s Web Interface via IPv4. The NCU’s front panel port
will have the following IPv6 Address. IPv6 Link-Local Address: fe80::209: f5ff:
fe09:1002/64 or IPv6 Address: 20fa: fffd: fffc:fffb:fffa:fff9:fff8:fff7. Enter the IPv6
Link-Local Address: [fe80::209: f5ff: fe09:1002/64] or IPv6 Address:
[20fa:fffd:fffc:fffb:fffa:fff9:fff8:fff7] to access the NCU’s Web Interface via IPv6.
2. When finished, disconnect your computer from the NCU.

Disabling Proxy Server Settings to Enable a Connection to the Controller over an Intranet Network
(if required)
NOTE! This procedure needs to be performed only when the controller is connected to an
Intranet and the User’s computer is set to access the Intranet through a proxy server. Note
that if the controller is connected to the Internet and the User’s computer is connected to an
Intranet, the User may not be able to disable the proxy server and access the controller.
If the controller’s Ethernet port is connected to your company’s Intranet Network and your
computer is also connected to the Intranet Network but requires access via a proxy server, you
must disable the proxy server settings to access the controller. Follow the procedure below to
disable the proxy server settings.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 29

Procedure
NOTE! Internet Explorer is used in this procedure, other browsers are similar.

3. Launch “Internet Explorer”.

4. Select Internet Options from the Tools menu. The “Internet Options” window opens.
In the “Internet Options” window, select the Connections tab.

5. Click on the LAN Settings... button. The following window opens. In the LAN Settings
window, uncheck the Proxy Server box and click OK.

Internet Security Settings for Loading Files or Downloading Files into the NCU
Your computer’s security settings may prevent you from loading files or downloading files into the
NCU. Refer to the following procedure to set your computer’s security settings to allow for this.
Procedure
NOTE! Internet Explorer is used in this procedure, other browsers are similar.

1. Launch “Internet Explorer”.

2. Select Internet Options from the Tools menu. The “Internet Options” window opens.
In the “Internet Options” window, select the General tab.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 30

 3. Under “Browsing History”, click on the Settings button. The following window opens.
In the Settings window, choose “Every time I visit the webpage” and click OK.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 31

 4. In the “Internet Options” window, select the Security tab.

5. Click on Trusted sites. With “Trusted sites” selected, click “Sites”. The following
window opens. Uncheck the “Require server verification (https:) for all sites in the
zone:” box if https is not being used.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 32

 6. In the Trusted sites window, type or copy the NCU URL in the “Add this website to the
zone:” box.

7. Click Add. The NCU URL is listed in the Websites: box. Click Close.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 33

Logging into the Controller via Web Interface Access
Procedure
Internet Explorer, version 6 or newer, is supported (IE 8.0 is recommended). Chrome, Safari, and
Firefox are also supported.
1. In your browser, enter http:// and the controller’s IP address (see “Connecting a Local
Computer Directly to the Controller when the System is NOT Equipped with an IB4
Board” on page 27 or “Connecting a Local Computer Directly to the Controller when
the System IS Equipped with an IB4 Board” on page 29) and press ENTER. If your site
requires secure HTTP and you were furnished with an NCU configuration with secure
HTTP, enter https:// and the controller’s IP address and press ENTER.
2. The following Web Interface Login window opens. Enter a valid User Name and
Password, then click LOGIN.
NOTE! By default, the “User Name” is "admin" and the “Password” is “640275”. The
password can be changed if necessary (see “Users Tab” on page 184).
NOTE! Before entering a User Name and password, you can select a local language that the
Web Interface menus use from those listed in the top right corner of the login window. See
“Language Tab” on page 191.

3. After entering a valid User Name and Password and clicking LOGIN, the Web Interface
"HOMEPAGE" window opens. Refer to “Web Interface Screens” on page 122.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 34

You can program a “Forgot Your Password” feature. Once programmed, if you forgot your
password, click Forgot Your Password? in the login screen. A "Find Password" window opens.
Enter your User Name and click Find Password. The controller sends the password to the email
address programmed for this User Name.

• To set up the “Forgot Password” feature, you must have a User set up with an email address
and you must set up the Alarm Reporting SMTP section. To program the User, in the Web
Interface, go to Advanced Settings Menu / Users Tab / select the User / enter a valid email
address for this User / repeat for all Users (see “Users Tab” on page 184). To program the
Alarm Reporting SMTP section, in the Web Interface, go to Advanced Settings Menu / Alarm
Report Tab / SMTP Section / enter at a minimum the following parameters: “Email To”
address, Server IP (IPV4 Server address), Server Port, “Email From” address. If email
authentication is required, then the SMTP Account and SMTP Password needs to be
configured as well. (See “Alarm Report Tab” on page 204.)

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 35

Common Tasks Performed via the Local Keypad and/or Web Interface
Procedures
Refer also to “Local Display Menus ” on page 97 and “Web Interface Screens” on page 122 for menu
item descriptions.
NOTE! Ensure current configuration is backed up prior to changing settings (see “Backing Up
the NCU Configuration” on page 50). Create new backup files after every successful update
for your records and in case of controller failure.
NOTE! If you add or remove hardware from the system (except rectifiers, solar converters, or
converters), update the inventory via the “Auto Config” menu item (see “Updating the NCU
Controller’s Device Inventory” on page 50).
NOTE! Some settings are restricted by other settings. Refer to Figure 13 for setting
restrictions.

Start Wizard
For initial startup, perform the Start Wizard from the local keypad and display to enter basic
programmable parameters in one session. Refer to “Start Wizard Sub-Menu (accessed from
Settings Menu)” on page 107 and “Start Wizard Now” on page 119.

Viewing Alarms
Local Menu Navigation:
Main Menu / Alarm Icon / ENT.
Web Menu Navigation:
Active alarms are listed in the lower right window pane. If the window pane is collapsed, click the
"arrow" icon to expand the alarm list.

Viewing System Status

Local Menu Navigation:
Main Menu / Input Power Icon / ENT.
Main Menu / Module Icon / ENT.
Main Menu / DC Icon / ENT.
Main Menu / Battery Icon / ENT.
Web Menu Navigation:
System status is displayed in the right window pane of the Home page. Select the Power System
tab and use the interactive links to view the various device group status pages. See “Device Group
Status Pages” starting on page 127.

Viewing the NCU Controller’s Device Inventory

Local Menu Navigation:
Main Menu / ESC to view Info Screens / ENT to view Inventory.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 36

Web Menu Navigation:
System Inventory Menu.

Clearing or Resetting Alarms

Local Menu Navigation:
Main Menu / Settings Icon / Alarm Settings / select alarm to clear or reset.
Web Menu Navigation:
Advance Settings Menu / Clear Data Tab / select Alarm History to clear.

Clearing Logs
Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / Clear Data Tab / select log to clear.

Changing the Local LCD Display Orientation

M830B Only: The rotation of the text in the local menus can be changed to allow the controller to
be mounted in different orientations. If the text is not in the proper orientation for your
application, change the LCD Rotation setting.
Local Menu Navigation:
Main Menu / Settings Icon / Sys Settings / LCD Rotation.
Web Menu Navigation:
None

Disabling the Local Keypad Sound

Local Menu Navigation:
Main Menu / Settings Icon / Sys Settings / Keypad Sound.
Web Menu Navigation:
None.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 37

Blocking Alarms
Local Menu Navigation:
Main Menu / Settings Icon / Alarm Settings / Alarm Blocked.
Web Menu Navigation:
Settings Menu / System Tab /Power System/ Outgoing Alarms Blocked.

Changing the Date and Time

Local Menu Navigation:
Main Menu / Settings Icon / Sys Settings / Date.
Main Menu / Settings Icon / Sys Settings / Time.
Date: Use the Up Arrow and Down Arrow to select the date field. Press ENT. Use Up Arrow and
Down Arrow to select the year then press ENT, next use Up Arrow and Down Arrow to select the
month then press ENT, and finally use Up Arrow and Down Arrow to select the day then press ENT.
Time: Use the Up Arrow and Down Arrow to select the time field. Press ENT. Use Up Arrow and
Down Arrow to select the hour then press ENT, next use Up Arrow and Down Arrow to select the
minute then press ENT, and finally use Up Arrow and Down Arrow to select the second then press
ENT.
Web Menu Navigation:
Settings Menu / Time Settings Tab.
In the Specify Time section, click on "Get Local Time from Connected PC" and then “Set” to
automatically set the date and time. To manually set the date and time, click on “the clock symbol”
and enter the date and time. See Figure 9. Then select the “Confirm” button. Then click on “Set”
to save the change.

Figure 9: Manual Date and Time Menu

Adding, Deleting, and Modifying Users

Local Menu Navigation:
None.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 38

Web Menu Navigation:
Advance Settings Menu / Users Tab.

Setting IP Communications Parameters

(if controller not set as DHCP or DHCPv6)
See also “Setting IPv4 Communications Parameters (if controller not set as DHCP)” on page 25 and
“Setting IPv6 Communications Parameters (if controller not set as DHCPv6)” on page 26.
Local Menu Navigation:
Main Menu / Settings Icon / Comm Settings / enter parameters.
Web Menu Navigation:
Advance Settings Menu / Ethernet Tab / enter parameters.

Setting for DHCP and DHCPv6

The DHCP and DHCPv6 functions allow the controller to acquire an IP address automatically. This
function can only be enabled or disabled via the local display and keypad. If this function is enabled
and the acquisition of an IP address fails, an alarm is generated. If the acquisition of an IP address is
successful, you need to record the IP address automatically acquired by the controller to access the
controller via the Web Interface. This IP address is displayed on the main system info screen (Main
Menu / ESC) in the IP Address field or in the local display menu (Main Menu / Settings Icon / Comm
Settings) in the IP Address field below the DHCP setting.
Local Menu Navigation:
Main Menu / Settings Icon / Comm Settings / DHCP (set to enabled) (can also view acquired IP
address).
Main Menu / ESC (to view acquired IP address).
Web Menu Navigation:
None.

Setting SNMP Parameters

Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / SNMP Tab.

Setting Auto Equalize

Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Charge / Auto EQ.
Also enter additional parameters from Web Interface (Settings Menu / Battery Tab / enter
parameters)
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Automatic Equalize (set to Yes) then enter the following
parameters.
• Equalize Start Current

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 39

 • Equalize Start Capacity
• Equalize Stop Current
• Equalize Stop Delay Time
• Maximum Equalize Charge Time
Programming the Audible Alarm Feature
Local Menu Navigation:
Main Menu / Settings Icon / Alarm Settings / Audible Alarm.
Web Menu Navigation:
None
Manually Forcing LVDs
Local Menu Navigation:
Main Menu / Settings Icon / Maintenance / “Auto/Man” State (change to Manual).
then
Main Menu / Settings Icon / Maintenance / LVD 1 Control or LVD 2 Control (select the other state).
then
Main Menu / Settings Icon / Maintenance / LVD 1 Control or LVD 2 Control (select the original
state).
then
Main Menu / Settings Icon / Maintenance / “Auto/Man” State (change to Auto).
Web Menu Navigation:
Settings Menu / System Tab / Power System/“Auto/Manual” State (change to Manual).
then
Settings Menu / LVD Tab / LVD 1 Control or LVD 2 Control (select the other state).
then
Settings Menu / LVD Tab / LVD 1 Control or LVD 2 Control (select the original state).
then
Settings Menu / System Tab / “Auto/Manual” State (change to Auto).

Manually Forcing Relays

After completing the following steps, the relay will momentarily toggle to the chosen state. The
relay then reverts back to being controlled by the NCU.
NOTE! This may take a few minutes.

Local Menu Navigation:

None.
WEB Menu Navigation:
Settings Menu / System Tab / Power System/ “Auto/Manual” State (change to Manual).
then
Settings Menu / System Tab / Power System / Relay Output # (select the other state).
then
Settings Menu / System Tab / EIB Equipment / EIB 1 / Relay Output # (select the other state).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 40

then
Settings Menu / System Tab / Power System / “Auto/Manual” State (change to Auto).
Assigning Severity Level to Alarms
Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / Alarms Tab and DI Alarms Tab.

Assigning Relays to Alarms

Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / Alarms Tab and DI Alarms Tab.

Placing the System in Float or Equalize Charge Mode

Local Menu Navigation:
Main Menu / Settings Icon / Maintenance / “EQ/FLT Control”.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / “Equalize/Float” Charge Control.

Viewing/Changing the Float Voltage Setting

Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Charge / Float Voltage.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Float Charge Voltage.

Viewing/Changing the Equalize Voltage Setting

Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Charge / EQ Voltage.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Equalize Charge Voltage.

Setting Battery Parameters

Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / navigate menus and enter parameters.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / enter parameters.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 41

Setting Battery Capacity Parameters
NOTE! After setting the battery capacity, the User should also reset the battery capacity
(battery must be fully charged). (from the Web Interface; Settings Menu / Battery Tab / Reset
Battery Capacity) (from the Local Interface; Settings Menu / Batt Settings / Basic Settings /
Reset Batt Cap).
Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Batt1 Settings or Batt2 Settings / Rated Capacity.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Batt1 Rated Capacity and Batt2 Rated Capacity.
or
See “Individual Battery Settings Page” on page 140.

Setting Rectifier High Voltage Shutdown

Local Menu Navigation:
None.
Web Menu Navigation:
Settings Menu / Rectifiers Tab / HVSD (set to enabled) then set HVSD Limit.

Setting Solar Converter High Voltage Shutdown

Local Menu Navigation:
None.
Web Menu Navigation:
Settings Menu / Solar Tab / HVSD Limit.

Setting Rectifier Current Limit

Local Menu Navigation:
Main Menu / Settings Icon / Rect Settings / Current Limit (set to enabled) then set Curr Limit Pt.
Web Menu Navigation:
Settings Menu / Rectifiers Tab / Current Limit (set to enabled) then set Current Limit Point.

Checking the Controller’s Current Limit Point after Adding or Removing a Rectifier or Converter
Module
If a rectifier or converter module is added; the respective current limit point in amps will
automatically increase to maintain the same percentage. For example, if the current limit was set
to 100% of combined capacity and a module is added, the new current limit setpoint will be 100%
of the combined capacity including the new module.
If a rectifier or converter is removed from the system (and the Rect Comm Fail or Conv Comm Fail
alarm is cleared); the respective current limit point will remain unchanged unless the capacity of
the remaining rectifiers or converters is not sufficient to maintain this current limit point. If that
happens, the current limit point will automatically decrease to the maximum (121% of the
remaining rectifiers or 116% of the remaining converters).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 42

It is recommended that the current limit point be checked whenever a rectifier or converter module
is added to or removed from the power system.
When setting total rectifier or total converter current limit, the set point to each unit is the total set
point divided by the number of units. For example, if the system contains five rectifiers and the
current limit is set to 150 amps then each rectifier has a current limit set point of 30 amps. If one or
more rectifiers or converters are removed or fails, it will take several seconds for the individual set
points to the remaining rectifiers or converters to be reset. In the example given, if one rectifier is
removed the current limit set point will drop to 120 amps (30 amps times four remaining rectifiers)
until the controller can send updated set points to the remaining rectifiers. This takes a couple
communication cycles (several seconds) after which each rectifier would have a new set point of
37.5 amps for a total of 150 amps. The total current limit of the rectifiers and converters should
not be set such that the loss of the redundant rectifiers or converters will cause this temporary set
point to drop below the actual maximum expected load. If batteries are used on the rectifier
output, the batteries should support the load until the current limit set points can be re-established
due to loss of a rectifier.

Enabling Solar Mode

When solar converters are all installed prior to applying power and starting system, the NCU will
NOT communicate with solar converters until SOLAR MODE is enabled. To enable SOLAR MODE,
refer to the following procedure.
Local Menu Navigation:
None.
Web Menu Navigation:
Settings / System Tab / Solar Mode / set to “SOLAR” or “RECT-SOLAR” or “Disabled”. Reboot the
controller (see “Rebooting the Controller” on page 52).
If you have both rectifiers and solar converters in the system, you have an option to set Solar Mode
to “RECT-SOLAR”. In the Battery Settings tab you set the “Float Charge Voltage (Solar)” parameter
to the desired float setting. The parameter “Float Charge Voltage (Rect)” setting MUST be set 0.3 V
lower than the “Float Charge Voltage (Solar)” parameter setting for solar converters to operate
properly.

Setting Over Voltage Alarm 1

Local Menu Navigation:
Main Menu / Settings Icon / Other Settings / Over Voltage 1.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Over Voltage 1.

Setting Over Voltage Alarm 2

Local Menu Navigation:
Main Menu / Settings Icon / Other Settings / Over Voltage 2.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Over Voltage 2.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 43

Setting Under Voltage Alarm 1
Local Menu Navigation:
Main Menu / Settings Icon / Other Settings / Under Voltage 1.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Under Voltage 1.

Setting Under Voltage Alarm 2

Local Menu Navigation:
Main Menu / Settings Icon / Other Settings / Under Voltage 2.
Web Menu Navigation:
Settings Menu / Battery Charge Tab / Under Voltage 2.

Setting Temperature Sensors

Temperature sensors may be connected to the…
• System Temperature Ports 1, 2, 3 (if available),
• Temp1 and Temp2 ports on an IB2 Interface Board,
• Temp1 and Temp2 ports on an EIB Interface Board, and
• Temp1 through Temp8 ports of up to eight (8) SM-Temp modules.
Each port (sensor) may be set as None, Battery, or Ambient.
A temperature sensor set as an ambient temperature sensor may also be set as the sensor which
displays the ambient temperature on the Web Interface’s Homepage.
A temperature sensor set as a battery temperature sensor may also be set as the temperature
compensation sensor (in addition, the temperature compensation sensor is the sensor which
displays the battery temperature on the Web Interface’s Battery Device Group Status Page).
A temperature sensor set as a battery temperature sensor may also be set as the BTRM (Battery
Thermal Runaway Management) sensor (in addition, the BTRM sensor is the sensor which is used
for the High Temperature Disconnect [HTD] Feature.)
Procedure
1. Set each temperature sensor in the system to None, Battery, or Ambient.
Local Menu Navigation:
None.
Web Menu Navigation:
Settings Menu / Temp Probes Tab.
Also enter values for the temp probe temperature alarms from the Web Interface (Settings
Menu / Temp Probes Tab).
2. If desired, set a temperature sensor set as an ambient temperature sensor as the
sensor which displays the ambient temperature on the Web Interface’s Homepage.
Local Menu Navigation:
None.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 44

 Web Menu Navigation:
Settings Menu / System Tab / Ambient Temp Sensor.
Also enter values for the ambient temperature alarms from the Web Interface (Settings
Menu / System Tab).
3. If desired, set a temperature sensor set as a battery temperature sensor as the
battery temperature compensation sensor.
Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Temp Comp / TempComp Sensor.
Web Menu Navigation:
Settings Menu / Battery Tab / Temp Compensation Probe.
Also enter values for the compensation temperature alarms from the Web Interface
(Settings Menu / Battery Tab).
4. If desired, set a temperature sensor set as a battery temperature sensor as the BTRM
sensor.
Local Menu Navigation:
None.
Web Menu Navigation:
Settings Menu / Temperature Tab / BTRM Temp Sensor.
Also enter values for the BTRM temperature alarms from the Web Interface (Settings Menu
/ Battery Tab).

Setting Battery Charge Temperature Compensation

The following need to be set for the Battery Charge Temperature Compensation feature.
See above for selecting the battery temperature compensation temperature sensor (or select
maximum, average, or Average SMBRC) and setting compensation temperature alarms.
Refer to “Specifications” on page 232 for temperature probe and reading accuracy.
Local Menu Navigation:
Main Menu / Settings Icon / Batt Settings / Temp Comp.
Enter values for the following parameters: TempComp Center, Temp Comp Coeff, Temp Comp
Clamp, Temp Comp Max V, Temp Comp Min V (note that you have to enable “Temp Comp Clamp”
to set the Temp Comp Max V and Min V values).
Web Menu Navigation:
Settings Menu / Battery Charge Tab.
Enter values for the following parameters:
Temp Compensation Center, Temp Comp Coefficient (slope), Temp Comp Voltage Clamp, Temp
Comp Max Voltage, and Temp Comp Min Voltage (note that you have to enable “Temp Comp
Voltage Clamp” to set the Temp Comp Max Voltage and Min Voltage values).

Setting Battery Thermal Runaway Management (BTRM) Feature

The following need to be set for the Battery Thermal Runaway Management (BTRM) feature.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 45

See above for selecting the Battery Thermal Runaway Management (BTRM) temperature sensor
and setting BTRM temperature alarms.
Local Menu Navigation:
None.
Web Menu Navigation:
Settings Menu / Battery charge Tab.
Enter values for the following parameters:
“BTRM Action” and “BTRM Voltage”.

Configuring the NCU Identification of Rectifiers and

Assigning which Input Feed is Connected to the Rectifiers
When rectifiers are all installed prior to applying power and starting the system, the order in which
the NCU identifies the rectifiers is by serial number (lowest serial number is Rect 1, next lowest is
Rect 2, etc.). If you prefer the NCU to identify the rectifiers by position in the system, perform the
following procedure.
Upon power up, the NCU arbitrarily assigns Phase A, B, or C to each rectifier. This assignment is
used to display rectifier AC input phase voltage(s). The User may reassign the feed to each rectifier
per your specific installation by following the procedure below.
Local Menu Navigation:
None.
Web Menu Navigation:
See “Individual Rectifier Settings Page” on page 130 and set the Rectifier ID and AC Feed (repeat for
every rectifier).
then
Settings Menu / Rectifiers Tab / “Confirm Rect ID/Feed”.

Configuring the NCU Identification of Solar Converters

When solar converters are all installed prior to applying power and starting the system, the order in
which the NCU identifies the solar converters is by serial number (lowest serial number is Solar
Conv 1, next lowest is Solar Conv 2, etc.). If you prefer the NCU to identify the solar converters by
position in the system, perform the following procedure.
NOTE! See also “Enabling Solar Mode” on page 43.

Local Menu Navigation:

None.
Web Menu Navigation:
See “Individual Solar Converter Settings Page” on page 133 and set the Solar Converter ID (repeat
for every solar converter).
then
Settings Menu / Solar Converters Tab / Confirm Solar Converter ID.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 46

Configuring the NCU Identification of Converters
When converters are all installed prior to applying power and starting the system, the order in
which the NCU identifies the converters is by serial number (lowest serial number is Conv 1, next
lowest is Conv 2, etc.). If you prefer the NCU to identify the converters by position in the system,
perform the following procedure.
Local Menu Navigation:
None.
Web Menu Navigation:
See “Individual Converter Settings Page” on page 135 and set the Converter ID (repeat for every
converter).
then
Settings Menu / “DC/DC” Converters Tab / Confirm Converter ID.

Setting Digital Inputs

Local Menu Navigation:
None.
WEB Menu Navigation:
Advance Settings Menu / DI Alarms Tab

Setting Battery Block and Battery Midpoint Monitoring (if equipped with an EIB Assembly)
Local Menu Navigation:
None.
WEB Menu Navigation:
Settings Menu / Battery Charge Tab / and enter the following parameters.
Parameters
• EIB-# Voltage Type
• EIB-# Block In-Use Num
• EIB-# Block Voltage Diff or Block Voltage Diff (Mid)

Setting External Shunts (connected to the EIB Assembly)

Local Menu Navigation:
None.
WEB Menu Navigation:
Advance Settings Menu / Shunts Tab / EIB-# / press “Modify/View” and enter the following
parameters. When done, press “Set”.
Parameters
• Set As (Not Used, General, Load, Battery, Source)
• Signal Full Name
• Signal Abbr Name

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 47

 • Full Scale Current
• Full Scale Voltage
• Break Value (Device Rating)
• High 1 Curr Limit Alarm (% of Breaker Value)
• High 1 Curr Alarm Severity
• High 1 Curr Alarm Relay
• High 2 Curr Limit Alarm (% of Breaker Value)
• High 2 Curr Alarm Severity
• High 2 Curr Alarm Relay
WEB Menu Navigation (for shunts set as battery):
See “Individual Battery Settings Page” on page 140.
Parameters
• EIB#Battery #, Rated Capacity

Setting External Shunts (connected to the SMDU+ Assembly)

Local Menu Navigation:
None.
WEB Menu Navigation:
Advance Settings Menu / Shunts Tab / SMDUP # / press “Modify/View” and enter the following
parameters. When done, press “Set”.
Parameters
• Set As (enabled, disabled)
• Signal Full Name
• Signal Abbr Name
• Full Scale Current
• Full Scale Voltage
• Break Value (Device Rating)
• High 1 Curr Limit Alarm (% of Breaker Value)
• High 1 Curr Alarm Severity
• High 1 Curr Alarm Relay
• High 2 Curr Limit Alarm (% of Breaker Value)
• High 2 Curr Alarm Severity
• High 2 Curr Alarm Relay

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 48

Setting Shunts (connected to the SMDU Assembly)
Local Menu Navigation:
None.
WEB Menu Navigation:
Advance Settings Menu / Shunts Tab / SMDU # / press “Modify/View” and enter the following
parameters. When done, press “Set”.
Parameters
• Set As (Not Used, General, Load, Battery, Source)
• Signal Full Name
• Signal Abbr Name
• Full Scale Current
• Full Scale Voltage
• Break Value (Device Rating)
• High 1 Curr Limit Alarm (% of Breaker Value)
• High 1 Curr Alarm Severity
• High 1 Curr Alarm Relay
• High 2 Curr Limit Alarm (% of Breaker Value)
• High 2 Curr Alarm Severity
• High 2 Curr Alarm Relay
WEB Menu Navigation (for shunts set as battery):
Settings Menu / Quick Settings Tab / Signal Settings Section / SMDU#Batt# Rated Capacity and
enter the following parameters.
Parameters
• SMDU#Batt#, Rated Capacity

Clearing the Maintenance Alarm

A maintenance time can be set which, once expires, issues a maintenance alarm. When the
maintenance alarm is issued, perform the routine maintenance and reset the maintenance timer.
To reset the maintenance timer and clear the Maintenance Alarm, clear the Maintenance Run Time.
Local Menu Navigation:
None.
WEB Menu Navigation:
Settings Menu / System Tab / Power System / “Auto/Manual” State (change to Manual).
then
Settings Menu / System Tab / Power System / Clear Maintenance Run Time.
then

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 49

Settings Menu / System Tab / Power System / “Auto/Manual” State (change to Auto).

Performing a Manual Battery Discharge Test

Procedure
1. Check that the Rated Battery Capacity is set up correctly for each battery.
Local Menu: Main Menu / Settings Icon / Batt Settings / Battery Test.
Web Menu: Settings Menu / Battery Test
2. Check that the following Battery Test parameters are set correctly: Test Voltage
Level, End Test Voltage, End Test Time, End Test Capacity, Record Threshold.
Local Menu: Main Menu / Settings Icon / Batt Settings / Battery Test.
Web Menu: Settings Menu / Battery Test.
3. Wait for the test to end.
4. View the battery test log and upload it to your computer as required. See “Battery
Test Log Tab” on page 174.
Updating the NCU Controller’s Device Inventory
Local Menu Navigation:
Main Menu / Settings Icon / Other Settings / Auto Config.
Web Menu Navigation:
Advance Settings Menu / SW Maintenance Tab / Auto Config.

Backing Up the NCU Configuration

To back up the NCU configuration, simply save the file named "SettingParam.tar".
NOTE! It is strongly recommended that you save a copy of the “SettingParam.tar” file
whenever you make any changes to the NCU. Then, if you ever replace the NCU or perform a
"Restore Defaults" procedure, you can restore your customized settings by downloading the
previously saved “SettingParam.tar” file back into the NCU.
Prior to changing NCU settings, ensure the current "SettingParam.tar" file is backed up. After
making changes, create a new backup file.
To aid in file management, you may change the name of the "SettingParam.tar" file to differentiate
it from other "SettingParam.tar" files saved. The new name can use alpha and numeric characters
preceding the original "SettingParam.tar" name (the end of the new file name must always be
"SettingParam.tar"; for example, an acceptable filename would be "seville4SettingParam.tar").
Saving the “SettingParam.tar” File
Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / SW Maintenance Tab.
See “Retrieve "SettingParam.tar" File Procedure” on page 195 to retrieve the “SettingParam.tar”
file.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 50

Reloading a Backed-Up NCU Configuration
To reload the NCU configuration, simply download a saved "SettingParam.tar" file into the NCU.
Reloading the “SettingParam.tar” File
Local Menu Navigation:
None.
Web Menu Navigation:
Advance Settings Menu / SW Maintenance Tab.
See “Upload/Download Procedure” on page 196 to download a "SettingParam.tar" file into the
NCU.
Upgrading the NCU Using an Application ("All") Package
This procedure is typically used to upgrade your NCU when a new release of firmware is available
for your application. The name of the Application "All" Package file must end in .tar or .tar.gz. An
Application “All” package file has both the application (software) and "SettingParam.tar" file and is
usually supplied for an application upgrade.
A User can copy an Application ("All") Package from your computer to a USB memory device. You
can then place the USB memory device into the NCU USB port and then download the file into the
NCU Controller. If upgrading the NCU with a USB drive other than the supplied USB, the following
USB drive specifications must be adhered to:
• USB 2.0 or below, 32G or less, formatted fat32 file system.
Local Menu Navigation (To Download an Application ("All") Package):
1. Copy the file to a USB memory device. The file must be in the root directory of the
USB memory device. The file must be named app_V#.#.##.tar.gz.
NOTE! #.#.## is the revision number (i.e. 1.1.40, 4.1.40, etc.).

2. Connect the USB memory device to the USB port on the front of the controller.
3. Navigate to “Main Menu / Settings Icon / Sys Settings / Update App / select yes”.
Once Yes is selected and confirmed, the configuration file located on the memory
device located in the controller's USB port is loaded into the controller.
4. A percent (%) complete will be displayed and when finished the NCU will reboot
automatically
5. The controller enters an initialization routine, which takes a few minutes. The routine
is complete, and the controller is operational when normal system voltage is
displayed on the screen.
6. Remove the memory device.
Web Menu Navigation (To Download an Application ("All") Package):
Advance Settings Menu / SW Maintenance Tab.
See “Upload/Download Procedure” on page 196 to download an Application (“All”) Package into
the controller.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 51

Restoring Factory Default Configuration
This procedure is used to restore all changes made to the NCU to factory defaults.
Procedure
ALERT! When this procedure is performed, the controller’s existing configuration and
parameter settings will be lost. The “SettingParam.tar” file is deleted. Before restoring the
factory default configuration, if you have made any changes to the NCU, save the
“SettingParam.tar” file (see Backing Up the NCU Configuration on page 50).
Local Menu Navigation:
Main Menu / Settings Icon / Sys Settings / Restore Default.
Web Menu Navigation:
Advance Settings Menu / SW Maintenance Tab.
See “Restore Factory Default Configuration Procedure” on page 194.
NOTE! SOME SYSTEMS REQUIRE CHANGES TO THE NCU CONFIGURATION DURING FINAL
TEST BEFORE BEING SHIPPED. These systems are supplied with a USB memory device that
contains a “SettingParam.tar” file as shipped. If provided, the “SettingParam.tar” file has a
seven-digit UIN (Unique Identification Number) preceding the “SettingParam.tar” filename.
The UIN identifies a “SettingParam.tar” file for use with a specific system. This file can be
used to restore your system to the configuration as shipped. Refer to “Reloading a Backed-Up
NCU Configuration” on page 51 to reload the supplied “SettingParam.tar” file.
TO RESTORE THESE SYSTEMS TO THE NCU CONFIGURATION AS SHIPPED, RESTORE DEFAULTS AS
DESCRIBED ABOVE; THEN RELOAD THE SUPPLIED "SETTINGPARAM.TAR" FILE.

Rebooting the Controller

Local Menu Navigation:
At the Main Screen, press ENT and ESC at the same time to reset the NCU Controller.
Web Menu Navigation:
Advance Settings Menu / SW Maintenance Tab / Reboot Controller button.

Changing the Names of Items Displayed in the LCD and Web-Interface Menus
Local Menu Navigation: none.
WEB Menu Navigation:
Navigate to the appropriate tab in the Advance Settings menu. Press “Modify” and enter the signal
name parameter(s). When done, press “Set”.
Digital Inputs
Advance Settings Menu / DI Alarms Tab.
Shunts
Advance Settings Menu / Shunts Tab.
Fuses
Advance Settings Menu / Fuse Tab.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 52

Power Split Feature
In Power Split applications, the output of the power system controlled by the NCU can be
connected in parallel with an existing power system. Each system is controlled independently via
its own controller. The NCU power system is referred to as the "slave" system and the existing
power system as the "master" system. The Power Split feature controls the NCU power system’s
output voltage and rectifiers' current limit so that the "slave" power system shares the load with
the "master" system.
Optional Functions: The NCU controller can mimic the equalize and battery test functions of the
“master” system’s controller. In addition, the NCU controller can mimic the low voltage load
disconnect and/or low voltage battery disconnect functions of the “master” system. This is
accomplished by supplying digital signals from the “master” system’s controller to the NCU. This
allows these functions to remain active in the “master” system.
How Power Split Works
There are four User adjustable parameters for Power Split. They are:
• Power Split Current Limit Value: Current limit point for power system designated as “slave
system” in a "Power Split" configuration.
• Delta Voltage: The offset voltage that the power system designated as “slave system” in a
"Power Split" configuration is set to. It is suggested to leave this value at the default (0.5
volts).
• Proportion Coeff: The proportional coefficient that the power system designated as “slave
system” in a "Power Split" configuration is set to. It is suggested to leave this value at the
default (30%).
• Integral Time: The integral time that the power system designated as “slave system” in a
"Power Split" configuration is set to. It is suggested to leave this value at the default (60
seconds).
The NCU controller uses these parameters to control the load sharing operation between the two
power systems.
Depending on the systems’ configurations, their rectifier capacities, their distribution load
capacities, and the Power Split configuration; four operating modes can occur.
Low Load Operation
When the total load current demand is lower than the Power Split Current Limit Value, the NCU
power system voltage will be increased by the programmed DELTA VOLTAGE setting forcing the
NCU power system to carry the load. Make sure that the output voltage does not exceed the
battery float range recommended by the manufacturer. In this operating mode, no current will be
delivered by the existing power system.
Normal Load Operation
When the total load current demand reaches the Slave Current Limit Value, the NCU power system
operates in output current limit and its output voltage will be decreased (up to the DELTA VOLTAGE
setting) in order to regulate the current, allowing the existing power system to deliver the
remaining current. Both the NCU power system and the existing power system are now providing
current to the load.
High Load Operation
If current demand increases and the existing power system reaches its current limit setting, float
voltage will again begin to decrease. When the voltage falls below the float setting minus the
DELTA VOLTAGE setting, the NCU system will come out of current limit and now deliver the

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 53

additional current necessary to satisfy the load. This operation may occur when the batteries are
being recharged, such as after a commercial AC failure.
Over Load Operation
If the load current is greater than the combined current capacities of the NCU system and the
existing power system, both power systems will go into current limit. Both systems and the
batteries will feed the load. The output voltage will depend on the conditions of the batteries. This
operation occurs if the total capacity of the rectifiers is too low in relation to the need for increased
current.
Operating Modes
Figure 5 illustrates the four modes of operation described above.
The Normal Load Operation is considered to be the normal mode. In this mode both the NCU
system and the existing parallel power system are both delivering load current. This is main
purpose of using Power Split, to avoid putting the burden of delivering the entire load onto one of
the two power systems.
Requirements and Conditions
The two DC power systems must be connected in parallel as described in “Paralleling the Existing
and NCU Power Systems” on page 55.
Before paralleling the two systems, the following conditions must be met for proper Power Split
function.
NOTE! The control features of the combined system are limited to those of the original power
system.

NOTE! The same type of batteries with an equal amount of cells and the same charging
voltages must be used for both systems.
• The float voltage, equalize voltage, and battery test voltage of the NCU power system must
be set to the same levels as that of the existing power system.
• The remote sense, if available and connected, of both the NCU power system and existing
power system must be connected to the same point.
• If batteries are used, they must be of the same type.
• All the functions specific to the existing power system and NCU power system and which
depend on the voltage or which act on the voltage must be disabled from the existing power
system and NCU power system. This includes the following…
a) any equalization function,
b) any temperature compensation function,
c) any charge control function,
d) any battery discharge test function, and
e) any invalid current alarm.
In lieu of this, if battery charging and battery test functions are implemented in the existing power
system, they can remain if signals for starting are connected from the control system of the existing
system to the NCU system.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 54

Paralleling the Existing and NCU Power Systems
Important Safety Instructions
General Safety
DANGER! YOU MUST FOLLOW APPROVED SAFETY PROCEDURES.
Performing the following procedures may expose you to hazards. These procedures should
be performed by qualified technicians familiar with the hazards associated with this type of
equipment. These hazards may include shock, energy, and/or burns. To avoid these hazards:
a) The tasks should be performed in the order indicated.
b) Remove watches, rings, and other metal objects.
c) Prior to contacting any uninsulated surface or termination, use a voltmeter to verify that
no voltage or the expected voltage is present. Check for voltage with both AC and DC
voltmeters prior to making contact.
d) Wear eye protection.
e) Use certified and well-maintained insulated tools. Use double insulated tools
appropriately rated for the work to be performed.
AC Input Voltages
DANGER! This system operates from AC input voltage capable of producing fatal electrical
shock.

DC Output and Battery Voltages

DANGER! Connecting the NCU power system to an existing power system for “Power Split”
mode involves working on live equipment carrying live loads. This system produces DC
Power and may have a battery source connected to it. Although the DC voltage is not
hazardously high, the rectifiers and/or battery can deliver large amounts of current. Exercise
extreme caution not to inadvertently contact or have any tool inadvertently contact an
output terminal or battery terminal or exposed wire connected to an output terminal or
battery terminal. NEVER allow a metal object, such as a tool, to contact more than one
termination or battery terminal at a time, or to simultaneously contact a termination or
battery terminal and a grounded object. Even a momentary short circuit can cause sparking,
explosion, and injury. Remove watches, rings, or other jewelry before connecting leads.
Cover any live busbars with a canvas sheet to prevent short circuits caused by falling tools or
parts.
Preparing the Existing and NCU Power Systems
• Install and turn-up the NCU power system as describe in the installation instructions
furnished with the power system.
• Set the float voltage on both the existing and NCU power systems to the same level.
Temperature compensation functionality, if used, should be disabled on both power
systems.
Paralleling the Systems
• Connect the Battery and Battery Return busbars of the NCU Power System to the main
charge busbars (rectifier side of the shunt) on the parallel power system. Size the cable for
the largest current between systems.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 55

 Note 1:The connections between the two power systems should be done with power cables
appropriately sized to be capable of carrying the maximum current that can circulate
between the two power systems.
Note 2:If the parallel power system incorporates a main plant shunt, the connections of the
cables from the NCU power system to the parallel power system shall be made on the
main charge busbars (rectifier side of the shunt).
Note 3:To compensate for voltage drop, it is recommended to connect the NCU power
system’s remote sense leads (if available) to the same point of sensing as the parallel
power system.
Note 4:There shall be only one battery return reference (BRR) cable for the two power
systems. If the cable is appropriately sized on the parallel power system, keep it as
the BRR for both power systems. If the cable is not appropriately sized on the parallel
power system, install a new BRR cable and connect it preferably to the NCU power
system since the parallel power system may eventually be phased out.
Note 5:If battery disconnect units (BDUs) are used on the new or parallel power system,
these shall be wired in such a way as to be all triggered simultaneously in order to
prevent any overloading of these.
Note 6:For the size and number of bridge cables between the two power systems, take into
consideration the voltage drop, the available connecting points in each system, as
well as the fact that these cables are unfused and shall therefore be run on a
dedicated cable rack. “C” or “H” taps may be used to make full use of available
connecting points.
Note 7:The legacy system retains the function of its controller and the percent of load on
each plant is controlled by the NCU. Alarms may be sent individually from each plant,
or combined using an NCU Interface Board and the programmable relays resident in
the controller.
Note 8:Add a label on both power systems to indicate that these are operating in the Power
Split Mode with each other.
• Optional Function Connections: The following signals from the existing system must be
connected to digital inputs of the NCU system interface board for these functions to be
active: Equalize Charge in Progress, Battery Test in Progress, Load LVD Active, and Battery
LVD Active. Otherwise disable these functions.
Programming the NCU Power Split Feature
After an NCU power system has been connected to an existing power system and both systems set
for the same float voltage, you will have to configure the Power Split parameters in the NCU.
Procedure
1. In the Web Interface menus, set the Power Split mode to enabled. Navigate to
Settings Menu / System / Power System / PowerSplit Mode. Set this parameter to
“enabled”.
2. Reboot the NCU by pressing ESC and ENT at the same time.
3. Navigate to Settings Menu / System / Power System.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 56

 4. Set the “Power Split Current Limit Value” to a value that will force the NCU system’s
rectifiers to operate in current limiting mode.
NOTE! The Power Split Current Limit Value must be set lower than the total distribution
current from the two plants. The default value is 60% of the NCU power system’s rectifier
capacity.
5. Set the “Delta Voltage”. This voltage is by default set to 0.5 V but can be readjusted.
• If the distribution current is lower than 50% of the total capacity of the NCU power
system, the “Delta Voltage” can be adjusted to a lower level than 0.5 V to get a system
voltage that is closer to the desired float charging voltage.
• If the voltage drop between the existing system and the NCU system is expected to be
>0.5 V, the “Delta Voltage” can be adjusted to a higher level than 0.5 V to get a correct
split function.
• Temperature controlled battery charging cannot be set in the NCU power system in
power split mode. If this function is implemented in the existing power system, a limited
function within a temperature range of approximately ±15 °C will be achieved if the Delta
Voltage is set to a higher level, maximum 2.00 V.
• If the “Delta Voltage” 0.5 V is considered to be too high, the split function can be tested
at various modes of operation to find a lower setting.
Optional Function Setup
Equalize Charge Setup
If the equalize charge function is to be used, equalize charge must be implemented in the existing
power system and an equalizing signal from its control unit must be connected to the NCU.
1. In the Web Interface menus, navigate to Settings Menu / Battery Charge/ Equalize
Charge Voltage. Set the “Equalize Charge Voltage” to the same value as the equalize
voltage of the existing power system.
2. Using the Web Interface menus (see “Power Split Tab” on page 208), select the NCU
digital input connected to the existing systems equalize control circuit.
NOTE! Equalize charging is controlled by the existing power system via an incoming digital
signal. The system will remain at the set equalize charge voltage level as long as this signal is
active.
Battery Test Setup
If the battery test function is to be used, battery test must be implemented in the existing power
system and a test signal from its control unit must be connected to the NCU.
1. In the Web Interface menus, navigate to Settings Menu / Battery Test.
2. Set the “End Test Voltage” to the same value as the end voltage of the existing power
system.
3. Set the “Test Voltage Level” to the same value as the test voltage of the existing
power system.
4. Using the Web Interface menus (see “Power Split Tab” on page 208), select the NCU
digital input connected to the existing systems battery test control circuit.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 57

 NOTE! Other settings in this menu regarding “Battery Test” are inactive.

NOTE! Battery test is controlled by the existing power system via an incoming digital signal.
The system will remain at battery test as long as this signal is active.
Low Voltage Disconnect Setup
If low voltage disconnect functions are to be used, they must be implemented in the existing power
system and signals from its control unit must be connected to the NCU.
5. Using the Web Interface menus (see “Power Split Tab” on page 208), select the NCU
digital inputs connected to the low voltage disconnect control circuits.
Temperature Compensated Battery Charge
There is no possibility to activate the “Temperature Compensated Battery Charge” function when
the NCU power system is configured for “Power Split” mode.
However, the possibility to change the “Delta Voltage” enables the NCU power system to follow the
existing power system that has the functionality to a certain limit.
Example: The “Delta Voltage” in the NCU power system is set to 1.0V. The existing power system is
set to compensate 3.0 mV/cell/°C. This means that the NCU power system can follow the
temperature compensation of the existing; power system in the range of ±14 °C from the set
normal battery temperature (3.0 mV x 24 cells x 14 °C = 1.008 V).
Verifying the Operation of the Power Split Feature
After programming the “Power Split” feature, verify its operation as follows.
6. In a Power Split application where the NCU power system is taking the entire load and
the rectifiers in the existing power system are all in the standby mode, use an
external dry load bank of sufficient capacity to increase the load on the NCU power
system over the “SLAVE CURRENT LIMIT” value.
a) Verify that the NCU power system limits the total output of its rectifiers to the current
equivalent to this programmed percentage.
b) Verify that the NCU power system lowers its output voltage by the value of the
programmed “DELTA VOLTAGE”.
c) Verify that the rectifiers in the existing power system take the additional load as the load
increases pass the “SLAVE CURRENT LIMIT” value.
d) Further increase the load in order to exceed the total capacity of the rectifiers in the
existing power system (or shut down some of the rectifiers in the existing power system
if the capacity of the external dry load bank is not sufficient). Verify that the NCU power
system starts taking the additional load as soon as the total capacity of the rectifiers in
the existing power system is exceeded.
7. In a Power Split application where the NCU power system is taking only part of the
load (operating continuously at the current level equivalent to the programmed
“SLAVE CURRENT LIMIT” percentage) and the rectifiers in the existing power system
are taking the rest of the load, use an external dry load bank of sufficient capacity to
increase the load in order to exceed the total capacity of the rectifiers in the existing
power system (or shut down some of the rectifiers in the existing power system if the
capacity of the external dry load bank is not sufficient).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 58

 e) Verify that the NCU power system starts taking the additional load as soon as the total
capacity of the rectifiers in the existing power system is exceeded.

Resolving Alarms
Table 4 lists the alarms that are shown in the Web Interface Advance Settings Menu under the
Alarms Tab. These are also the possible alarms that display in the alarm screens on the local display
and Web Interface. Table 4 also provides guidelines for fixing the condition that caused the alarm.
NOTE! These instructions describe the complete functionality of the controller. Some
functionality is dependent on hardware connected to the controller. Some alarms listed may
not display in your system or may be named differently. Refer to the NCU Configuration
Drawing (C-drawing) furnished with your system.
Refer also to the NCU Configuration Drawing (C-drawing) furnished with your system for the factory
default “Alarm Severity Level” settings and “Alarm Relay” mapping to the available alarms.

Table 4: Available Alarms

Table 4
Alarm Name Alarm Description Action to Correct
Power System Alarms
Supervision Unit Fail Controller self-detection test fails. Replace the controller.
CAN bus communications failure.
CAN Communication Failure No devices communicating on Check communications cables.
CAN bus.
Alarm relays are forced in the
Verify why controller setting was
Outgoing Alarms Blocked "off" state and alarms are blocked
changed before changing back.
from changing the relay state.
Maintenance Time Limit Controller issues a maintenance Perform routine maintenance and
Alarm alarm. reset maintenance timer.
Config Error (Backup Config) Configuration error 1. Reload the "SettingParam.tar"
Config Error (Default Config) Configuration error 2. file.
When a load shunt is furnished,
the system load current
Check why current is imbalanced.
measurement is imbalanced with
Check what current is not being
Imbalance System Current internally calculated system load
reported correctly (load, rectifier,
current. This is a check to see if
battery, etc.).
the shunt reading is accurate and
makes sense.
Over Load Output overload condition. Check the load.
Surge protection device needs
SPD Check surge protection device.
attention.
System in emergency stop or Check why the system was placed
EStop/EShutdown
emergency shutdown mode. in this mode.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 59

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor port #1 is not
System Temp 1 Not Used
used.
Temperature sensor port #2 is not
System Temp 2 Not Used --
used.
Temperature sensor port #3 is not
System Temp 3 Not Used
used.
Temperature sensor port #1 (on
IB2-1 Temp 1 Not Used
IB2-1 Board) is empty.
Temperature sensor port #2 (on
IB2-1 Temp 2 Not Used
IB2-1 Board) is empty.
Temperature sensor port #1 (on
IB2-2 Temp 1 Not Used
IB2-2 Board) is empty.
Temperature sensor port #2 (on
IB2-2 Temp 2 Not Used
IB2-2 Board) is empty.
--
Temperature sensor port #1 (on
EIB-1 Temp 1 Not Used
EIB-1 Board) is empty.
Temperature sensor port #2 (on
EIB-1 Temp 2 Not Used
EIB-1 Board) is empty.
Temperature sensor port #1 (on
EIB-2 Temp 1 Not Used
EIB-2 Board) is empty.
Temperature sensor port #2 (on
EIB-2 Temp 2 Not Used
EIB-2 Board) is empty.
System Temp 1 Sensor Fail Temperature sensor #1 failure.
System Temp 2 Sensor Fail Temperature sensor #2 failure. Replace temperature sensor.
System Temp 3 Sensor Fail Temperature sensor #3 failure.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 60

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
IB2-1 Temp 1 Sensor Fail (connected to IB2-1 Board)
failure.
Temperature sensor #2
IB2-1 Temp 2 Sensor Fail (connected to IB2-1 Board)
failure.
Temperature sensor #1
IB2-2 Temp 1 Sensor Fail (connected to IB2-2 Board)
failure.
Temperature sensor #2
IB2-2 Temp 2 Sensor Fail (connected to IB2-2 Board) Replace temperature sensor.
failure.
Temperature sensor #1
EIB-1 Temp 1 Sensor Fail
(connected to EIB-1 Board) failure.
Temperature sensor #2
EIB-1 Temp 2 Sensor Fail
(connected to EIB-1 Board) failure.
Temperature sensor #1
EIB-2 Temp 1 Sensor Fail
(connected to EIB-2 Board) failure.
Temperature sensor #2
EIB-2 Temp 2 Sensor Fail
(connected to EIB-2 Board) failure.
The DHCP function is enabled, but
DHCP Failure effective IP address cannot be Verify DHCP IP address.
acquired.
PLC Config Error PLC configuration error. Re-enter the PLC logic functions.
485 Communication Failure 485 communications failure. --
Observation alarm summary (one
Observation Summary or more alarms designated as Check additional alarms.
minor is active).
Major alarm summary (one or
Major Summary more alarms designated as major Check additional alarms.
is active).
Critical alarm summary (one or
Critical Summary more alarms designated as critical Check additional alarms.
is active).
A rectifier group cannot be Check communications cables.
Rectifier Group Lost
detected by the controller. Check additional alarms.
Output voltage is higher than the
Over Voltage 1
Over Voltage 1 Alarm threshold. Check why system voltage is high.
Output voltage is higher than the Check the alarm setting.
Over Voltage 2
Over Voltage 2 Alarm threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 61

Table 4
Alarm Name Alarm Description Action to Correct
Check why system voltage is low.
Output voltage is lower than the If there is a mains failure, check if
Under Voltage 1
Under Voltage 1 Alarm threshold. some load could be switched off
in order to prolong the operating
time of the plant. If the system
load is too high related to rectifier
capacity, install additional
Output voltage is lower than the rectifiers. If the batteries are
Under Voltage 2
Under Voltage 2 Alarm threshold. being recharged, the alarm will
cease by itself when battery
voltage has increased to the
charging level.
Output voltage is higher than the
Over Voltage 1 (24V)
Over Voltage 1 Alarm threshold. Check why system voltage is high.
Output voltage is higher than the Check the alarm setting.
Over Voltage 2 (24V)
Over Voltage 2 Alarm threshold.
Check why system voltage is low.
Output voltage is lower than the If there is a mains failure, check if
Under Voltage 1 (24V)
Under Voltage 1 Alarm threshold. some load could be switched off
in order to prolong the operating
time of the plant. If the system
load is too high related to rectifier
capacity, install additional
Output voltage is lower than the rectifiers. If the batteries are
Under Voltage 2 (24V)
Under Voltage 2 Alarm threshold. being recharged, the alarm will
cease by itself when battery
voltage has increased to the
charging level.
Diesel generator run over
DG Over Temperature Check diesel generator.
temperature alarm.
Genset Control Genset is controlling --
Hybrid Config Error Hybrid config is error. Check the hybrid config.
DG Fuel Low Level DG fuel is in low level. Check the DG fuel.
DG Control Failed DG control is failed. Check why DG control is failed.
High diesel generator ambient
Ambient Temp High 1
temperature alarm1.
Low diesel generator ambient Check why temperature is high or
Ambient Temp Low
temperature alarm. low.
High diesel generator ambient
Ambient Temp High 2
temperature alarm2.
Ambient temperature sensor
Ambient Sensor Fail Replace temperature sensor.
failure.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 62

Table 4
Alarm Name Alarm Description Action to Correct
NCU Digital input #1 alarm is
DI1 Alarm
active.
NCU Digital input #2 alarm is
DI2 Alarm
active.
NCU Digital input #3 alarm is
DI3 Alarm
active.
NCU Digital input #4 alarm is
DI4 Alarm
active.
Check why alarm is active.
NCU Digital input #5 alarm is
DI5 Alarm
active.
NCU Digital input #6 alarm is
DI6 Alarm
active.
NCU Digital input #7 alarm is
DI7 Alarm
active.
NCU Digital input #8 alarm is
DI8 Alarm
active.
IB Communication Fail IB Communication Fail. --
Relay Test Relay Test in progress. --
Relay1 Test Relay1 Test in progress. --
Relay2 Test Relay2 Test in progress. --
Relay3 Test Relay3 Test in progress. --
Relay4 Test Relay4 Test in progress. --
Relay5 Test Relay5 Test in progress. --
Relay6 Test Relay6 Test in progress. --
Relay7 Test Relay7 Test in progress. --
Relay8 Test Relay8 Test in progress. --
Hybrid cyclic boost charge is in
Hybrid Cyclic BC in process --
process

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 63

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1 sensing
System Temp1 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #1 sensing
System Temp1 High 1 temperature higher than high
temperature threshold 1.
Temperature sensor #1 sensing
System Temp1 Low temperature lower than low
temperature threshold.
Temperature sensor #2 sensing
System Temp2 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #2 sensing
Check why temperature is high or
System Temp2 High 1 temperature higher than high
low.
temperature threshold 1.
Temperature sensor #2 sensing
System Temp2 Low temperature lower than low
temperature threshold.
Temperature sensor #3 sensing
System Temp3 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #3 sensing
System Temp3 High 1 temperature higher than high
temperature threshold 1.
Temperature sensor #3 sensing
System Temp3 Low temperature lower than low
temperature threshold.
Temperature sensor #1
(connected to IB2-1 board and set
IB2-1 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to IB2-1 board and set
Check why temperature is high or
IB2-1 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to IB2-1 board and set
IB2-1 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 64

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #2
(connected to IB2-1 board and set
IB2-1 Temp2 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to IB2-1 board and set
Check why temperature is high or
IB2-1 Temp2 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to IB2-1 board and set
IB2-1 Temp2 Low as Ambient) sensing temperature
lower than low temperature
threshold.
Temperature sensor #1
(connected to IB2-2 board and set
IB2-2 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to IB2-2 board and set
Check why temperature is high or
IB2-2 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to IB2-2 board and set
IB2-2 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 65

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #2
(connected to IB2-2 board and set
IB2-2 Temp2 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to IB2-2 board and set
Check why temperature is high or
IB2-2 Temp2 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to IB2-2 board and set
IB2-2 Temp2 Low as Ambient) sensing temperature
lower than low temperature
threshold.
Temperature sensor #1
(connected to EIB-1 board and set
EIB-1 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to EIB-1 board and set
Check why temperature is high or
EIB-1 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to EIB-1 board and set
EIB-1 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 66

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #2
(connected to EIB-1 board and set
EIB-1 Temp2 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to EIB-1 board and set
Check why temperature is high or
EIB-1 Temp2 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to EIB-1 board and set
EIB-1 Temp2 Low as Ambient) sensing temperature
lower than low temperature
threshold.
Temperature sensor #1
(connected to EIB-2 board and set
EIB-2 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to EIB-2 board and set
Check why temperature is high or
EIB-2 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to EIB-2 board and set
EIB-2 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 67

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #2
(connected to EIB-2 board and set
EIB-2 Temp2 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to EIB-2 board and set
Check why temperature is high or
EIB-2 Temp2 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to EIB-2 board and set
EIB-2 Temp2 Low as Ambient) sensing temperature
lower than low temperature
threshold.
Temperature sensor #1
(connected to SM-Temp 1 and set
SMTemp1 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to SM-Temp 1 and set
Check why temperature is high or
SMTemp1 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to SM-Temp 1 and set
SMTemp1 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.
… … …

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 68

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #8
(connected to SM-Temp 1 and set
SMTemp1 Temp8 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #8
(connected to SM-Temp 1 and set
Check why temperature is high or
SMTemp1 Temp8 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #8
(connected to SM-Temp 1 and set
SMTemp1 Temp8 Low as Ambient) sensing temperature
lower than low temperature
threshold.
… … …
Temperature sensor #1
(connected to SM-Temp 8 and set
SMTemp8 Temp1 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to SM-Temp 8 and set
Check why temperature is high or
SMTemp8 Temp1 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to SM-Temp 8 and set
SMTemp8 Temp1 Low as Ambient) sensing temperature
lower than low temperature
threshold.
… … …

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 69

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #8
(connected to SM-Temp 8 and set
SMTemp8 Temp8 High 2 as Ambient) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #8
(connected to SM-Temp 8 and set
Check why temperature is high or
SMTemp8 Temp8 High 1 as Ambient) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #8
(connected to SM-Temp 8 and set
SMTemp8 Temp8 Low as Ambient) sensing temperature
lower than low temperature
threshold.
Load current above high level 1
High Load Level 1
setting.
Check why load current is high.
Load current above high level 2
High Load Level 2
setting.
NCU Digital input #9 alarm is
DI9 Alarm
active.
NCU Digital input #10 alarm is
DI10 Alarm
active.
Check why alarm is active.
NCU Digital input #11 alarm is
DI11 Alarm
active.
NCU Digital input #12 alarm is
DI12 Alarm
active.
Relay 14 Test Testing Relay DO1.4
Relay 15 Test Testing Relay DO15.
--
Relay 16 Test Testing Relay DO16.
Relay 17 Test Testing Relay DO17.
Over Maximum Power Alarm NOT IMPLEMENTED AT THIS TIME NOT IMPLEMENTED AT THIS TIME
SMS Modem Fail SMS modem has failed. Check why SMS modem failed.
Manual State NCU in manual state. --
SNMP Config Error SNMP configuration error. --
Ambient Temp Summary Ambient Temperature Summary
--
Alarm Alarm
Rectifier Group Alarms
Check input voltage to rectifiers.
Multiple Rectifiers Fail More than one rectifier has failed.
Replace rectifiers.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 70

Table 4
Alarm Name Alarm Description Action to Correct
A rectifier cannot be detected by Reset the Rectifier Lost alarm.
Rectifier Lost
the controller. Replace defective rectifier.
Rectifier Energy Optimization Check why system was placed into
ECO Active
Mode is enabled. this mode.
Check the connectors and cables
All Rectifiers Comm Fail No response from all rectifiers. or the CAN loop. Replace the
controller.
If Energy Optimization Mode is
enabled and the controller
Check for other alarms.
ECO Cycle Alarm oscillates in and out of Energy
Reset this alarm.
Optimization more than 5 times,
this alarm is generated.
Check why the rectifier capacity is
Low Rectifier Capacity The rectifier capacity is low.
low.
Check why the rectifier capacity is
High Rectifier Capacity The rectifier capacity is high.
high.
Rectifier Alarms
Check why no AC input power
AC Input Fail No AC input power to a rectifier.
available.
A rectifier has a high temperature
Rect Temperature High Check why temperature is high.
condition.
Rectifier Fail A rectifier has a fault condition.
A rectifier has an overvoltage Refer to Rectifier User Manual for
HVSD
condition. troubleshooting information.
Rectifier Protected A rectifier is in protected mode.
Fan Fail A rectifier’s fan has failed. Replace fan.
Current Limit A rectifier is in current limit. --
A rectifier has lost Check communications cables.
Rectifier Communication Fail communications with the Reset the Communication Fail
controller. alarm. Replace the rectifier.
A rectifier is in output power
Derated
derating mode.
A rectifier has a current sharing Refer to Rectifier User Manual for
Current Share Alarm
alarm. troubleshooting information.
A rectifier is in under voltage
AC Under Voltage Protection
protection mode.
Rectifier Group 2 [3, 4] Alarms
Check the connectors and cables
All Rectifiers Comm Fail No response from all rectifiers. or the CAN loop. Replace the
controller.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 71

Table 4
Alarm Name Alarm Description Action to Correct
A rectifier cannot be detected by Reset the Rectifier Lost alarm.
Rectifier Lost the controller. Replace defective rectifier.
A rectifier has lost Reset the Comm Fail alarm.
Communication Failure communications with the Replace defective rectifier.
controller.
Rectifier commercial AC input
Mains Failure --
power failure.
Check input voltage to rectifiers.
Multiple Rectifiers Fail More than one rectifier has failed. Replace rectifiers.
Group I [II, III] Rectifier Alarms
Check why no AC input power
AC Input Failure No AC input power to a rectifier. available.
A rectifier has a high temperature
Rectifier HighTemperature Check why temperature is high.
condition.
Rectifier Fault A rectifier has a fault condition.
A rectifier has an over voltage Refer to Rectifier User Manual for
Overvoltage condition. troubleshooting information.
Rectifier Protected A rectifier is in protected mode.
Fan Failure A rectifier’s fan has failed. Replace fan.
Power Limit A rectifier is in power limit. --
A rectifier has lost Check communications cables.
Rectifier Communication Fail communications with the Reset the Communication Fail
controller. alarm. Replace the rectifier.
A rectifier is in output power
Derated derating mode.
A rectifier has a current sharing Refer to Rectifier User Manual for
Current Sharing Alarm alarm. troubleshooting information.
A rectifier is in under voltage
AC Undervoltage Protection protection mode.
Battery Group Alarms

Short Battery Test Running Battery is in short time test mode. --

Battery is in equalize charge test

Equalize for Test --
mode.

Battery is in manual battery

Manual Test --
discharge test mode.

Battery is in planned battery test

Planned Test --
mode.

AC power has been switched off

AC Fail Test to the rectifiers to perform a --
battery discharge test.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 72

Table 4
Alarm Name Alarm Description Action to Correct

Battery is in manual equalize

Manual Equalize --
charging mode.

Battery is in automatic equalize

Automatic Equalize --
charging mode.

Battery is in cyclic equalize

Cyclic Equalize --
charging mode.

In Power Split mode, “Master”

Master Equalize starts equalize charging with the --
“Slave”.

In Power Split mode, “Master”

Master Battery Test --
starts the test with the “slave”.

The currents from two groups of

Battery distribution current
Discharge Current Imbalance batteries are not equal. Check the
imbalance alarm.
batteries.

The equalize charging current

Abnormal Battery Current Check the alarm setting.
exceeds the alarm setting.

Temperature Compensation Battery charge temperature

--
Active compensation is active.

Battery Current Limit Active Battery is in current limit. --

Bad Battery Battery test fails. Check the batteries.

A battery test is active (the

discharge test will stop
automatically). There is a mains
failure (check that it is not caused
Battery Discharge Battery is discharging. by open AC input circuit breaker).
The system load is higher than
rectifier capacity, causing the
batteries to discharge (install
additional rectifiers).

Battery Test Fail Battery test fails. Check the batteries.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 73

Table 4
Alarm Name Alarm Description Action to Correct
Compensation temperature
sensor sensing temperature
Comp Temp High2
higher than high temperature
threshold 2.
Compensation temperature
Check why temperature is high or
sensor sensing temperature
Comp Temp High1 low.
higher than high temperature
threshold 1.
Compensation temperature
Comp Temp Low sensor sensing temperature lower
than low temperature threshold.
Temperature Compensation
Compensation Sensor Fault Replace temperature sensor.
temperature sensor failure.
Temperature sensor #1 sensing
System Temp1 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #1 sensing
Check why temperature is high or
System Temp1 High 1 temperature higher than high
low.
temperature threshold 1.
Temperature sensor #1 sensing
System Temp1 Low temperature lower than low
temperature threshold.
Temperature sensor #2 sensing
System Temp2 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #2 sensing
Check why temperature is high or
System Temp2 High 1 temperature higher than high
low.
temperature threshold 1.
Temperature sensor #2 sensing
System Temp2 Low temperature lower than low
temperature threshold.
Temperature sensor #3 sensing
System Temp3 High 2 temperature higher than high
temperature threshold 2.
Temperature sensor #3 sensing
Check why temperature is high or
System Temp3 High 1 temperature higher than high
low.
temperature threshold 1.
Temperature sensor #3 sensing
System Temp3 Low temperature lower than low
temperature threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 74

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to IB2-1 board and set
IB2-1 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to IB2-1 board and set
Check why temperature is high or
IB2-1 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to IB2-1 board and set
IB2-1 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
Temperature sensor #2
(connected to IB2-1 board and set
IB2-1 Temp2 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to IB2-1 board and set
Check why temperature is high or
IB2-1 Temp2 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to IB2-2 board and set
IB2-1 Temp2 Low as Battery) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 75

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to IB2-2 board and set
IB2-2 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to IB2-2 board and set
Check why temperature is high or
IB2-2 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to IB2-2 board and set
IB2-2 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
Temperature sensor #2
(connected to IB2-2 board and set
IB2-2 Temp2 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to IB2-2 board and set
Check why temperature is high or
IB2-2 Temp2 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to IB2-2 board and set
IB2-2 Temp2 Low as Battery) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 76

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to EIB-1 board and set
EIB-1 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to EIB-1 board and set
Check why temperature is high or
EIB-1 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to EIB-1 board and set
EIB-1 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
Temperature sensor #2
(connected to EIB-1 board and set
EIB-1 Temp2 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to EIB-1 board and set
Check why temperature is high or
EIB-1 Temp2 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to EIB-1 board and set
EIB-1 Temp2 Low as Battery) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 77

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to EIB-2 board and set
EIB-2 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to EIB-2 board and set
Check why temperature is high or
EIB-2 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to EIB-2 board and set
EIB-2 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
Temperature sensor #2
(connected to EIB-2 board and set
EIB-2 Temp2 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #2
(connected to EIB-2 board and set
Check why temperature is high or
EIB-2 Temp2 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #2
(connected to EIB-2 board and set
EIB-2 Temp2 Low as Battery) sensing temperature
lower than low temperature
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 78

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to SM-Temp 1 and set
SMTemp1 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to SM-Temp 1 and set
Check why temperature is high or
SMTemp1 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to SM-Temp 1 and set
SMTemp1 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
… … …
Temperature sensor #8
(connected to SM-Temp 1 and set
SMTemp1 Temp8 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #8
(connected to SM-Temp 1 and set
Check why temperature is high or
SMTemp1 Temp8 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #8
(connected to SM-Temp 1 and set
SMTemp1 Temp8 Low as Battery) sensing temperature
lower than low temperature
threshold.
… … …

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 79

Table 4
Alarm Name Alarm Description Action to Correct
Temperature sensor #1
(connected to SM-Temp 8 and set
SMTemp8 Temp1 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #1
(connected to SM-Temp 8 and set
Check why temperature is high or
SMTemp8 Temp1 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #1
(connected to SM-Temp 8 and set
SMTemp8 Temp1 Low as Battery) sensing temperature
lower than low temperature
threshold.
… … …
Temperature sensor #8
(connected to SM-Temp 8 and set
SMTemp8 Temp8 High 2 as Battery) sensing temperature
higher than high temperature
threshold 2.
Temperature sensor #8
(connected to SM-Temp 8 and set
Check why temperature is high or
SMTemp8 Temp8 High 1 as Battery) sensing temperature
low.
higher than high temperature
threshold 1.
Temperature sensor #8
(connected to SM-Temp 8 and set
SMTemp8 Temp8 Low as Battery) sensing temperature
lower than low temperature
threshold.
Battery temperature (monitored
by the sensor set as BTRM) is
BTRM Temp High 2
higher than the BTRM
Temperature Alarm 2 threshold. Check why temperature is high or
Battery temperature (monitored low.
by the sensor set as BTRM) is
BTRM Temp High 1
higher than the BTRM
Temperature Alarm 1 threshold.
BTRM Sensor Fail BTRM temperature sensor failure. Replace temperature sensor.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 80

Table 4
Alarm Name Alarm Description Action to Correct
Check communications cables.
A Li-Ion Battery cannot be
Li-Ion Battery Lost Clear the Li-Ion Battery Lost
detected by the controller.
alarm.
One (1) Li-Ion Battery is Check why the Li-Ion Battery
1 Li-Ion Battery Disconnect
disconnected. disconnected.
Two (2) or more Li-Ion Batteries Check why the Li-Ion Batteries
2+Li-Ion Battery Disconnect
are disconnected. disconnected.
One (1) Li-Ion Battery has lost Check communications cables.
1 Li-Ion Battery No Reply communications with the Clear the Li-Ion Communication
controller. Fail alarm.
Two (2) Li-Ion Battery has lost Check communications cables.
2 Li-Ion Battery No Reply communications with the Clear the Li-Ion Communication
controller. Fail alarm.
Only available if NCU
configuration includes the Li-Ion
Inventory Update In Process battery interface. --
Li-Ion Battery inventory being
updated.
Only available if NCU
configuration includes the Li-Ion
ABCL is active battery interface. --
Active Battery Charge Current
Limit is active.
Only available if NCU
configuration includes the Li-Ion
Battery Charge Prohibited
battery interface. See why alarm is active.
Alarm
A battery charge prohibited alarm
is active.
Only available if NCU
configuration includes the Li-Ion
Battery Temperature
battery interface. See why alarm is active.
Summary Alarm
A battery temperature summary
alarm is active.
Battery 1 Alarms
Battery Current Limit Battery current limit point is
--
Exceeded exceeded.
Battery Over Current Battery is in over current. --
Low Battery Capacity Battery has low capacity. Check the batteries.
Battery Current High 1 Curr Current above High 1 limit.
Check why current is high.
Battery Current High 2 Curr Current above High 2 limit.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 81

Table 4
Alarm Name Alarm Description Action to Correct
Battery Fuse Alarms
Fuse 1 Alarm Fuse #1 is open. Find out and eliminate the reason
… … the fuse is open before replacing.
Check for overload or short
circuit. If the fuse was manually
Fuse 6 Alarm Fuse #6 is open. removed, check with the person
that removed it before reinserting
it.
SMDU Battery Fuse Unit Alarms (SMDU Module must be present in system)
Batt Fuse 1 Alarm Battery fuse #1 is open. Find out and eliminate the reason
… … the fuse is open before replacing.
Check for overload or short
circuit. If the fuse was manually
Batt Fuse 6 Alarm Battery fuse #4 is open. removed, check with the person
that removed it before reinserting
it.
SMDU Battery Alarms (SMDU Module must be present in system)
Battery current limit point is
Exceed Current Limit --
exceeded.
Over Battery Current Battery is in over current. --
Low Capacity Battery has low capacity. Check the batteries.
SM Battery Alarms (SM-BAT Module must be present in system)
Current Limit Exceeded Battery is in over current. --
Over Battery Current Battery current is high. --
Battery Leakage Battery has leakage current. Check the batteries.
Low Acid Level Battery has low acid level. Check the batteries.
Battery Disconnected Battery disconnection is active. --
Battery has high temperature
High Battery Temperature --
condition.
Battery has low temperature
Low Battery Temperature --
condition.
Battery cell voltage difference
Cell Voltage Difference Check the batteries.
detected.
Battery monitoring device has
SM-BAT Unit Failure failed. Replace device.
Battery Temperature Sensor Battery temperature sensor has
Failure failed. Replace temperature sensor.
Low Capacity Battery has low capacity. Check the batteries.
Battery monitoring device has lost
Battery Not Responding communications with the Check communications cables.
controller.
Temperature Sensor not Used No battery temperature sensor. --

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 82

Table 4
Alarm Name Alarm Description Action to Correct
SMBRC Battery Alarms (SM-BRC Module must be present in system)
Low Cell Voltage Alarm Battery string low voltage alarm. --
Battery string low temperature
Low Cell Temperature Alarm alarm. --
Battery string low resistance
Low Cell Resistance Alarm alarm. --
Low Inter Cell Resistance Battery string inter-cell low
Alarm resistance alarm. --
Low Ambient Temperature Battery string ambient low alarm. --
Alarm
High Total Voltage Battery string high voltage alarm. --
Low Total Voltage Battery string low voltage alarm. --
High String Current Battery string high current alarm. --
Low String Current Battery string low current alarm. --
High Ripple Current Battery string ripple current high. --
Low Ripple Current Battery string ripple current low. --
Battery string current limit
Current Limit Exceeded --
exceeded.
Over Battery Current Battery string over current alarm. --
Low Capacity Battery string low capacity alarm. --
High Cell Voltage Alarm Battery cell high voltage alarm. --
Battery cell high temperature
High Cell Temperature Alarm alarm. --
High Cell Resistance Alarm Battery cell high resistance alarm. --
Battery inter-cell high resistance
High Inter Cell Resist Alarm --
alarm.
High Delta Cell vs Ambient Battery cell high ambient --
Temp temperature alarm.
Battery Block 1 Temperature
Probe Failure
Battery temperature sensor has
… failed. Replace temperature sensor.
Battery Block 8 Temperature
Probe Failure
Temperature 9 Not Used Temperature sensor #9 not used.
… … --
Temperature 24 Not Used Temperature sensor #24 not used.
DC Distribution Alarms
Over Voltage1 DC voltage is high.
Check why DC voltage is high.
Over Voltage2 DC voltage is very high.
Under Voltage1 DC voltage is low.
Check why DC voltage is low.
Under Voltage2 DC voltage is very low.
Over Voltage1 (24V) DC voltage is high(24V). Check why DC voltage is high.
Over Voltage2 (24V) DC voltage is very high(24V).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 83

Table 4
Alarm Name Alarm Description Action to Correct
Under Voltage1 (24V) DC voltage is low(24V). Check why DC voltage is low.
Under Voltage2 (24V) DC voltage is very low(24V).
Current High Current Current above High 1 limit.
Check why current is high.
Current Very High Current Current above High 2 limit.
Current High 1 Curr Current above High 1 limit.
Check why current is high.
Current High 2 Curr Current above High 2 limit.
DC Fuse Unit Alarms
Fuse 1 Alarm DC output fuse #1 is open. Find out and eliminate the reason
… … the fuse is open before replacing.
Check for overload or short
circuit. If the fuse was manually
Fuse 12 Alarm DC output fuse #12 is open. removed, check with the person
that removed it before reinserting
it.
SMDU DC Fuse Alarms (SMDU Module must be present in system)
Fuse 1 Alarm DC output fuse #1 is open. Find out and eliminate the reason
… … the fuse is open before replacing.
Check for overload or short
circuit. If the fuse was manually
Fuse 16 Alarm DC output fuse #16 is open. removed, check with the person
that removed it before reinserting
it.
SMDUP1 [2, 3, 4, 5, 6, 7, 8] DC Fuse Alarms (SMDU+ Module must be present in system)
Fuse 1 Alarm DC output fuse #1 is open. Find out and eliminate the reason
… … the fuse is open before replacing.
Check for overload or short
circuit. If the fuse was manually
Fuse 25 Alarm DC output fuse #25 is open. removed, check with the person
that removed it before reinserting
it.
LVD Unit Alarms (Low voltage disconnect must be present in system)
LVD1 contactor is in disconnect
LVD 1 Disconnect --
mode.
LVD2 contactor is in disconnect
LVD 2 Disconnect --
mode.
LVD 1 Fail LVD1 contactor has failed. Check the contactor functions.
LVD 2 Fail LVD2 contactor has failed. Replace the contactor.
LVD Disabled LVD is disabled. Check why the LVD is disabled.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 84

Table 4
Alarm Name Alarm Description Action to Correct
LVD3 Unit Alarms
LVD3 contactor is in disconnect
LVD 3 Disconnect --
mode.
Check the contactor functions.
LVD 3 Fail LVD3 contactor has failed.
Replace the contactor.
SMDU LVD Alarms (SMDU Module must be present in system)
LVD1 contactor is in disconnect
LVD 1 Disconnect --
mode.
LVD2 contactor is in disconnect
LVD 2 Disconnect --
mode.
LVD 1 Contactor Fail LVD1 contactor has failed. Check the contactor functions.
LVD 2 Contactor Fail LVD2 contactor has failed. Replace the contactor.
Rectifier AC Alarms
Voltage between Line A and Line
Line AB Over Voltage1 B is higher than the High Line
Voltage AB Alarm threshold.
Check why voltage is high.
Voltage between Line A and Line
Line AB Over Voltage2 B is higher than the Very High Line
Voltage AB Alarm threshold.
Voltage between Line A and Line
Line AB Under Voltage1 B is lower than the Low Line
Voltage AB Alarm threshold.
Check why voltage is low.
Voltage between Line A and Line
Line AB Under Voltage2 B is lower than the Very Low Line
Voltage AB Alarm threshold.
Line BC Over Voltage1 Voltage between Line B and Line C
is higher than the High Line
Voltage BC Alarm threshold.
Check why voltage is high.
Line BC Over Voltage2 Voltage between Line B and Line C
is higher than the Very High Line
Voltage BC Alarm threshold.
Line BC Under Voltage1 Voltage between Line B and Line C
is lower than the Low Line Voltage
BC Alarm threshold.
Check why voltage is low.
Line BC Under Voltage2 Voltage between Line B and Line C
is lower than the Very Low Line
Voltage BC Alarm threshold.
Line CA Over Voltage1 Voltage between Line C and Line
A is higher than the High Line
Voltage CA Alarm threshold.
Check why voltage is high.
Line CA Over Voltage2 Voltage between Line C and Line
A is higher than the Very High Line
Voltage CA Alarm threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 85

Table 4
Alarm Name Alarm Description Action to Correct
Line CA Under Voltage1 Voltage between Line C and Line
A is lower than the Low Line
Voltage CA Alarm threshold.
Check why voltage is low.
Line CA Under Voltage2 Voltage between Line C and Line
A is lower than the Very Low Line
Voltage CA Alarm threshold.
L1 voltage is above high voltage
Phase A Over Voltage1 threshold.
Check why voltage is high.
L1 voltage is above very high
Phase A Over Voltage2 voltage threshold.
L1 voltage is below low voltage
Phase A Under Voltage1 threshold.
Check why voltage is low.
L1 voltage is below very low
Phase A Under Voltage2 voltage threshold.
L2 voltage is above high voltage
Phase B Over Voltage1 threshold.
Check why voltage is high.
L2 voltage is above very high
Phase B Over Voltage2 voltage threshold.
L2 voltage is below low voltage
Phase B Under Voltage1 threshold.
Check why voltage is low.
L2 voltage is below very low
Phase B Under Voltage2 voltage threshold.
L3 voltage is above high voltage
Phase C Over Voltage1 threshold.
Check why voltage is high.
L3 voltage is above very high
Phase C Over Voltage2 voltage threshold.
L3 voltage is below low voltage
Phase C Under Voltage1 threshold.
Check why voltage is low.
L3 voltage is below very low
Phase C Under Voltage2 voltage threshold.
Check why no commercial AC
Mains Failure Commercial AC power failure.
power.
OB AC Unit (OB-AC Module must be present in system)
L1 voltage is above over voltage 1
L1 Over Voltage 1 threshold.
Check why voltage is high.
L1 voltage is above over voltage 2
L1 Over Voltage 2 threshold.
L1 voltage is below under voltage
L1 Under Voltage 1 1 threshold.
Check why voltage is low.
L1 voltage is below under voltage
L1 Under Voltage 2 2 threshold.
L2 voltage is above over voltage 1
L2 Over Voltage 1 threshold.
Check why voltage is high.
L2 voltage is above over voltage 2
L2 Over Voltage 2 threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 86

Table 4
Alarm Name Alarm Description Action to Correct
L2 voltage is below under voltage
L2 Under Voltage 1 1 threshold.
Check why voltage is low.
L2 voltage is below under voltage
L2 Under Voltage 2 2 threshold.
L3 voltage is above over voltage 1
L3 Over Voltage 1 threshold.
Check why voltage is high.
L3 voltage is above over voltage 2
L3 Over Voltage 2 threshold.
L3 voltage is below under voltage
L3 Under Voltage 1 1 threshold.
Check why voltage is low.
L3 voltage is below under voltage
L3 Under Voltage 2 2 threshold.
Check why no commercial AC
Mains Failure Commercial AC power failure. power.
Commercial AC power voltage is
Severe Mains Failure too low. Check why voltage is low.
Check why no commercial AC
Mains Failure (Single) Commercial AC power failure. power.
Commercial AC power voltage is
Severe Mains Failure (Single) Check why voltage is low.
too low.
SMAC Alarms (SM-AC Module must be present in system)
Supervision Fail AC monitoring device has failed. --
Voltage between Line A and Line
High Line Voltage AB B above high voltage threshold.
Voltage between Line A and Line Check why voltage is high.
Very High Line Voltage AB B above very high voltage
threshold.
Voltage between Line A and Line
Low Line Voltage AB B below low voltage threshold.
Voltage between Line A and Line Check why voltage is low.
Very Low Line Voltage AB B below very low voltage
threshold.
Voltage between Line B and Line C
High Line Voltage BC above high voltage threshold.
Check why voltage is high.
Voltage between Line B and Line C
Very High Line Voltage BC above very high voltage threshold.
Voltage between Line B and Line C
Low Line Voltage BC below low voltage threshold.
Check why voltage is low.
Voltage between Line B and Line C
Very Low Line Voltage BC below very low voltage threshold.
Voltage between Line C and Line
High Line Voltage CA A above high voltage threshold.
Voltage between Line C and Line Check why voltage is high.
Very High Line Voltage CA A above very high voltage
threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 87

Table 4
Alarm Name Alarm Description Action to Correct
Voltage between Line C and Line
Low Line Voltage CA A below low voltage threshold.
Voltage between Line C and Line Check why voltage is low.
Very Low Line Voltage CA A below very low voltage
threshold.
L1 voltage is above high voltage
High Voltage L1 threshold.
Check why voltage is high.
L1 voltage is above very high
Very High Voltage L1 voltage threshold.
L1 voltage is below low voltage
Low Voltage L1 threshold.
Check why voltage is low.
L1 voltage is below very low
Very Low Voltage L1 voltage threshold.
L2 voltage is above high voltage
High Voltage L2 threshold.
Check why voltage is high.
L2 voltage is above very high
Very High Voltage L2 voltage threshold.
L2 voltage is below low voltage
Low Voltage L2 threshold.
Check why voltage is low.
L2 voltage is below very low
Very Low Voltage L2 voltage threshold.
L3 voltage is above high voltage
High Voltage L3 threshold.
Check why voltage is high.
L3 voltage is above very high
Very High Voltage L3 voltage threshold.
L3 voltage is below low voltage
Low Voltage L3 threshold.
Check why voltage is low.
L3 voltage is below very low
Very Low Voltage L3 voltage threshold.
Check why no commercial AC
Mains Failure Commercial AC power failure. power.
Commercial AC power voltage is
Severe Mains Failure Check why voltage is low.
too low.
Commercial AC power has high
High Frequency --
frequency.
Commercial AC power has low
Low Frequency frequency. --
AC input temperature sensor
High Temperature sensing high temperature --
condition.
AC input temperature sensor
Low Temperature sensing low temperature --
condition.
L1 High Current High L1 current. --
L2 High Current High L2 current. --
L3 High Current High L3 current. --

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 88

Table 4
Alarm Name Alarm Description Action to Correct
IB2-1 (Interface Board) Alarms (IB2-1 must be present in system)
IB2-1 board has lost
Communication Fail communications with the Check communications cables.
controller.
DI1 Alarm Digital input #1 alarm is active.
… …
Check why alarm is active.
DI7 Alarm Digital input #7 alarm is active.
DI8 ESTOP Digital input #8 alarm is active.
IB2-1 D01 Test Testing Relay 1 (on IB2-1 Board).
… … --
IB2-1 D08 Test Testing Relay 8 (on IB2-1 Board).
IB2-2 (Interface Board) Alarms (IB2-2 must be present in system)
IB2-2 board has lost
Communication Fail communications with the Check communications cables.
controller.
DI1 Alarm Digital input #1 alarm is active.
… …
Check why alarm is active.
DI7 Alarm Digital input #7 alarm is active.
DI8 ESTOP Digital input #8 alarm is active.
IB2-2 D01 Test Testing Relay 1 (on IB2-2 Board).
… … --
IB2-2 D08 Test Testing Relay 8 (on IB2-2 Board).
EIB-1 (Extended Interface Board) Alarms (EIB-1 board must be present in system)
EIB-1 board has lost
EIB Communication Fail communications with the Check communications cables.
controller.
Bad Battery Block Battery block fails. Check batteries.
EIB-1 D01 Test Testing Relay 1 (on EIB-1 Board).
… … --
EIB-1 D05 Test Testing Relay 5 (on EIB-1 Board).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 89

Table 4
Alarm Name Alarm Description Action to Correct
Current1 High 1 Current Current 1 above High 1 limit.
Current1 High 2 Current Current 1 above High 2 limit.
Current2 High 1 Current Current 2 above High 1 limit.
Check why current is high.
Current2 High 2 Current Current 2 above High 2 limit.
Current3 High 1 Current Current 3 above High 1 limit.
Current3 High 2 Current Current 3 above High 2 limit.
EIB-1 (Extended Interface Board) Battery Alarms (EIB-1 Board must be present in system)
Battery Current Limit Battery current limit point is
--
Exceeded exceeded.
Battery Over Current Battery is in over current. --
Battery Low Capacity Battery has low capacity. Check the batteries.
EIB-2 (Extended Interface Board) Alarms (EIB-2 board must be present in system)
EIB-2 board has lost
EIB Communication Fail communications with the Check communications cables.
controller.
Bad Battery Block Battery block fails. Check batteries.
EIB-2 D01 Test Testing Relay 1 (on EIB-2 Board).
… … --
EIB-2 D05 Test Testing Relay 5 (on EIB-2 Board).
Current1 High 1 Current Current 1 above High 1 limit.
Current1 High 2 Current Current 1 above High 2 limit.
Current2 High 1 Current Current 2 above High 1 limit.
Check why current is high.
Current2 High 2 Current Current 2 above High 2 limit.
Current3 High 1 Current Current 3 above High 1 limit.
Current3 High 2 Current Current 3 above High 2 limit.
EIB-2 (Extended Interface Board) Battery Alarms (EIB-2 Board must be present in system)
Battery Current Limit Battery current limit point is
--
Exceeded exceeded.
Battery Over Current Battery is in over current. --
Battery Low Capacity Battery has low capacity. Check the batteries.
SMDU Unit 1 [2, 3, 4, 5, 6, 7, 8] Alarms (SMDU Module must be present in system)
Distribution voltage is below
Under Voltage Check why system voltage is low.
under voltage threshold.
Distribution voltage is above over
Over Voltage Check why system voltage is high.
voltage threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 90

Table 4
Alarm Name Alarm Description Action to Correct
The SMDU 1 has lost
Communication Fail communications with the Check communications cables.
Controller.
Current1 High 1 Current Current 1 above High 1 limit.
Current1 High 2 Current Current 1 above High 2 limit.
… …
Check why current is high.
… …
Current5 High 1 Current Current 5 above High 2 limit.
Current5 High 2 Current Current 5 above High 2 limit.
Shunt1 Coefficient Conflict Shunt 1 coefficient conflicting.
… … Verify shunt size.
Shunt5 Coefficient Conflict Shunt 4 coefficient conflicting.
Current1 High 1 Current Current 1 above High 1 limit.
Current1 High 2 Current Current 1 above High 2 limit.
… …
Check why current is high.
… …
Current5 High 1 Current Current 5 above High 1 limit.
Current5 High 2 Current Current 5 above High 2 limit.
Converter Group Alarms
More than one converter has Check input voltage to converters.
Multiple Converters Fail
failed. Replace converters.
A converter cannot be detected Reset the Converter Lost alarm.
Converter Lost
by the Controller. Replace defective converter.
Check the connectors and cables
All Converters Comm Fail No response from all converters. or the CAN loop. Replace the
controller.
Over Current Over current condition exists. Check why.
Refer to Converter User Manual
Converter Protect A converter is in protected mode.
for troubleshooting information.
Converter Alarms
A converter has lost Check communications cables.
Communication Fail communications with the Reset the Communication Fail
controller. alarm. Replace the converter.
A converter has an over
Over Temperature Check why temperature is high.
temperature condition.
A converter has an overvoltage Refer to Converter User Manual
HVSD Alarm
condition. for troubleshooting information.
Fan Fail A converter’s fan has failed. Replace fan.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 91

Table 4
Alarm Name Alarm Description Action to Correct
Power Limit A converter is in power limit. --
Input voltage to a converter is
Low Input Volt --
low.
Converter Fail A converter has a fault condition.
EEPROM Fail A converter’s EEPROM has failed. Refer to Converter User Manual
A converter is in thermal for troubleshooting information.
Thermal Shutdown
shutdown.
Mod ID Overlap Converter module ID’s overlap. --
A converter has an under voltage
Under Voltage condition. --
(The hysteresis value is 2V.)
A converter has an over voltage
Over Voltage condition. --
(The hysteresis value is 2V.)
A converter has an under voltage
Under Voltage (24V) condition. --
(The hysteresis value is 1V.)
A converter has an over voltage
Over Voltage (24V) condition. --
(The hysteresis value is 1V.)
Converter alarm summary (one or
Converter Summary Alarm more alarms designated as “Manufacturer Use” Only.
converter is active).
SMDUP 1 [2, 3, 4, 5, 6, 7, 8] Unit Alarms (SMDU+ Module must be present in system)
Communication Fail Communications failure. Check communications cables.
Current1 High 1 Current Current 1 above High 1 limit. --
Current1 High 2 Current Current 1 above High 2 limit. --
… … --
… … --
Current25 High 1 Current Current 25 above High 1 limit. --
Current25 High 2 Current Current 25 above High 2 limit. --
Shunt Coefficient Conflict Shunt coefficient conflicting. Verify shunt size.
Fuel Tank Group Alarms
Fuel Group Communication Fuel tank group communication
Check communications cables.
Failure failure.
SMIO Generic Unit 1 Alarms (SM-IO Module must be present in system)
SMIO Failure SMIO has failed. --

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 92

Table 4
Alarm Name Alarm Description Action to Correct
SMIO Generic Unit 3 [4, 5, 6, 7, 8] Alarms (SM-IO Module must be present in system)
Input #1 above high alarm
High Analog Input 1 Alarm --
threshold.
Input #1 below low alarm
Low Analog Input 1 Alarm threshold. --
… … --
… … --
Input #5 above high alarm
High Analog Input 5 Alarm --
threshold.
Input #5 below low alarm
Low Analog Input 5 Alarm --
threshold.
Input frequency above high
High Frequency Input Alarm --
frequency alarm threshold.
Input frequency below low
Low Frequency Input Alarm frequency alarm threshold. --
SMIO Failure SM-IO board failure. Replace the board.
Testing Relay 1 Testing Relay 1.
Testing Relay 2 Testing Relay 2. --
Testing Relay 3 Testing Relay 3.
Diesel Generator Group Alarms
Diesel Test in Progress Diesel test in progress. --
Diesel Generator Test Failure Diesel test failed. --
Diesel Generator Alarms
Low DC Voltage Generator has low DC voltage. --
Diesel Generator Supervision Generator monitoring device has --
Fai failed.
Diesel Generator Failure Generator has failed. --
Generator is connected to the
Diesel Generator Connected --
system.
Low Fuel Level Generator has low fuel level. --
Generator has high water
High Water Temperature temperature. --
Low Oil Pressure Generator has low oil pressure. --
Periodical Maintenance Periodical maintenance is --
Required required to be performed.
SMDUH Unit 1 [2, 3, 4, 5, 6, 7, 8] Alarms (SMDUH Module must be present in system)
Distribution voltage is below low
Under Voltage Check why system voltage is low.
voltage threshold.
Distribution voltage is above high
Over Voltage Check why system voltage is high.
voltage threshold.
The SMDU 1 has lost
Communication Fail communications with the Check communications cables.
controller.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 93

Table 4
Alarm Name Alarm Description Action to Correct
SM-BRC Unit Alarms (SM-BRC Module must be present in system)
Communication Failure Communications failure. Check communications cables.
High Ambient Temperature Ambient high temperature alarm. --
Low Ambient Temperature Ambient low temperature alarm. --
Ambient Temperature Probe Ambient temperature sensor
Failure failure. Replace temperature sensor.

OBFuel Tank Alarms

High Fuel Level Alarm Fuel tank high level alarm. --
Low Fuel Level Alarm Fuel tank low level alarm. --
Fuel Theft Alarm Fuel tank theft alarm. --
Tank Height Error Fuel tank height error. --
Fuel Tank Config Error Fuel tank configuration error. --
DC Meter Group Alarms (DC Meter must be present in system)
DC meter cannot be detected by Reset the DC Meter Lost alarm.
DC Meter Lost
the controller. Replace defective DC Meter.
DC Meter Alarms (DC Meter must be present in system)
DC meter has lost
Communication Fail communications with the Check communications cables.
controller.
Solar Converter Group
Multiple Solar Converter Multiple solar converter has
Replace the solar converter.
Failure failed.
Solar Converter Lost Solar converter is lost. Replace the solar converter.
All Solar Converters Comm The communication of all solar
Check communications cables.
Fail converters has failed.
AC Meter (AC Meter must be present in system)
AC meter has lost
Communication Fail communications with the Check communications cables.
controller.
Voltage between Line A and Line
Line AB Over Voltage 1 B is higher than the Line AB Over
Voltage 1 Alarm threshold.
Check why voltage is high.
Voltage between Line A and Line
Line AB Over Voltage 2 B is higher than the Line AB Over
Voltage 2 Alarm threshold.
Voltage between Line A and Line
Line AB Under Voltage 1 B is lower than the Line AB Under
Voltage 1 Alarm threshold.
Check why voltage is low.
Voltage between Line A and Line
Line AB Under Voltage 2 B is lower than the Line AB Under
Voltage 2 Alarm threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 94

Table 4
Alarm Name Alarm Description Action to Correct
Voltage between Line B and Line C
Line BC Over Voltage 1 is higher than the Line BC Over
Voltage 1 Alarm threshold.
Check why voltage is high.
Voltage between Line B and Line C
Line BC Over Voltage 2 is higher than the Line BC Over
Voltage 2 Alarm threshold.
Voltage between Line B and Line C
Line BC Under Voltage 1 is lower than the Line BC Under
Voltage 1 Alarm threshold.
Check why voltage is low.
Voltage between Line B and Line C
Line BC Under Voltage 2 is lower than the Line BC Under
Voltage 2 Alarm threshold.
Voltage between Line C and Line
Line CA Over Voltage 1 A is higher than the Line CA Over
Voltage 1 Alarm threshold.
Check why voltage is high.
Voltage between Line C and Line
Line CA Over Voltage 2 A is higher than the Line CA Over
Voltage 2 Alarm threshold.
Voltage between Line C and Line
Line CA Under Voltage 1 A is lower than the Line CA Under
Voltage 1 Alarm threshold.
Check why voltage is low.
Voltage between Line C and Line
Line CA Under Voltage 2 A is lower than the Line CA Under
Voltage 2 Alarm threshold.
Phase A voltage is above over
Phase A Over Voltage 1 voltage 1 threshold.
Check why voltage is high.
Phase A voltage is above over
Phase A Over Voltage 2 voltage 2 threshold.
Phase A voltage is below under
Phase A Under Voltage 1 voltage 1 threshold.
Check why voltage is low.
Phase A voltage is below under
Phase A Under Voltage 2 voltage 2 threshold.
Phase B voltage is above over
Phase B Over Voltage 1 voltage 1 threshold.
Check why voltage is high.
Phase B voltage is above over
Phase B Over Voltage 2 voltage 2 threshold.
Phase B voltage is below under
Phase B Under Voltage 1 voltage 1 threshold.
Check why voltage is low.
Phase B voltage is below under
Phase B Under Voltage 2 voltage 2 threshold.
Phase C voltage is above over
Phase C Over Voltage 1 voltage 1 threshold.
Check why voltage is high.
Phase C voltage is above over
Phase C Over Voltage 2 voltage 2 threshold.
Phase C voltage is below under
Phase C Under Voltage 1 voltage 1 threshold.
Check why voltage is low.
Phase C voltage is below under
Phase C Under Voltage 2 voltage 2 threshold.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 95

Table 4
Alarm Name Alarm Description Action to Correct
Check why no commercial AC
Mains Failure Commercial AC power failure. power.
Commercial AC power voltage is
Severe Mains Failure too low. Check why voltage is low.
Commercial AC power has high
High Frequency --
frequency.
Commercial AC power has low
Low Frequency --
frequency.
AC input temperature sensor
High Temperature sensing high temperature --
condition.
AC input temperature sensor
Low Temperature sensing low temperature --
condition.
Phase A High Current High phase A current. --
Phase B High Current High phase B current. --
Phase C High Current High phase C current.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 96

LOCAL DISPLAY MENUS

Overview
This section provides descriptions of the Local Display Menus. Refer also to “Passwords and
Privilege Levels” on page 25 and “Description of Local Display Menus Programmable Parameters”
on page 112. For Web Interface, refer to “Web Interface Screens” on page 122.

Menus
Figure 10 to Figure 18 provide flow diagrams of the menus accessed via the NCU Controller local
display and keypad.

NOTE! These instructions describe the complete functionality of the NCU Controller. Some
functionality is dependent on hardware connected to the NCU Controller. Some menu items
shown may not be present in the NCU Controller used in your system.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 97

Main Menu
The Main Menu is shown in Figure 10. This is the first screen displayed when the local display is
activated by pressing any key on the NCU’s front panel.
The current displayed on the Main Menu is “total system current”. The “total system current”
equals total rectifier current or total solar converter current minus total battery current when
battery shunt exists or calculated battery current. If you do not calculate battery current, “total
system current” equals total rectifier current or total solar converter current.

Figure 10: Main Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 98

Controller Information Menu (accessed from the Main Menu)
Controller information screens can be accessed from the Main Menu as shown in Figure 11.

Figure 11: Controller Information Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 99

Alarm Menu
The Alarm Menu can be accessed from the Main Menu as shown in Figure 12.

Figure 12: Alarm Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 100

Settings Menu
The Settings Menu can be accessed from the Main Menu as shown in Figure 13.
Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 101

Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 102

Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 103

Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 104

Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 105

Figure 13: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 106

Start Wizard Sub-Menu (accessed from Settings Menu)
The Start Wizard menu can be accessed from the Settings Menu (in “Other Settings” sub-menu).
See Figure 14 for Start Wizard menu.

Figure 14: Start Wizard Sub-Menu (accessed from Setting's Menu)

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 107

Input Power Menu
The Input Power Menu can be accessed from the Main Menu as shown in Figure 15.

Figure 15: Input Power Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 108

Module Menu
The Module Menu can be accessed from the Main Menu as shown in Figure 16.

Figure 16: Module Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 109

DC Menu
The DC Menu can be accessed from the Main Menu as shown in Figure 17.

Figure 17: DC Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 110

Battery Menu
The Battery Menu can be accessed from the Main Menu as shown in Figure 18. The actual display
of the Battery Menu is dependent on the NCU configuration.

Figure 18: Battery Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 111

DESCRIPTION OF LOCAL DISPLAY MENUS
PROGRAMMABLE PARAMETERS
The following are descriptions of the programmable parameters presented in the local display
menus.

Settings Menu
See Figure 13.
Maintenance Sub-Menu
• Auto/Man State:
- Auto: The controller automatically controls the power system.
- Manual: A User can manually change certain power system control settings. When you
return to Auto Mode, any settings changed in Manual Mode are returned to their
previous setting (setting before being placed in Manual Mode). This provides a
convenient means of making temporary adjustment changes for testing purposes.
• EQ/FLT Control: Places the system in Equalize Charge or Float Charge mode.
• LVD 1 Control: Temporarily connects or disconnects LVD 1 when the controller is in Manual
mode. Setting returns to original when controller is returned to the Auto mode.
• LVD 2 Control: Temporarily connects or disconnects LVD 2 when the controller is in Manual
mode. Setting returns to original when controller is returned to the Auto mode.
• Rect Curr Limit: Maximum rectifier current setting .
• Over Voltage 1: Sets the Over Voltage 1 alarm point.
• Over Voltage 2: Sets the Over Voltage 2 alarm point.
• Under Voltage 1: Sets the Under Voltage 1 alarm point.
• Under Voltage 2: Sets the Under Voltage 2 alarm point.
Energy Saving Sub-Menu
• ECO Mode: Enables or disables the Energy Optimization Mode feature for all rectifiers.
When enabled, the following parameters can be set.
ALERT! The Energy Optimization Mode should NOT be used in systems that operate without
batteries.

• Best Oper Point: Percent of full load capacity that the rectifiers operate under in the Energy
Optimization mode.
• Fluct Range: If load fluctuation is less than this value, rectifiers are not turned on or off for
Energy Optimization.
• Cycle Period: This is the time period that rectifiers are turned on and off to maintain an
equal operating time for all rectifiers in the system.
• Rects ON Time: Time all rectifiers are turned on at the end of the “Cycle Period”.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 112

Alarm Settings Sub-Menu
• Audible Alarm: Programs the audible alarm feature.
- Off: Disables the audible alarm.
- On: When a new alarm occurs, the audible alarm sounds. Press any key to silence the
audible alarm.
- 3 min / 10 min / 1 hr / 4 hrs: When a new alarm occurs, the audible alarm sounds. The
audible alarm automatically silences after the selected time period.
• Alarm Blocked:
- Normal: Alarms are processed normally.
- Blocked: Forces the alarm relays in the "off" state and blocks alarms from changing the
relay state.
• ClrRectCommFail: Clears a rectifier communication fail alarm.
• ClrRectLost: Clears a rectifier lost alarm.
• Rst RectGrpLost: Resets rectifier group lost alarms.
• Clr Bad Bat Alm: Clears a bad battery alarm.
• ClrBatTestFail: Clears a battery test fail alarm.
• ClrCycleAlm: Clears a rectifier oscillator alarm.
• Clr AbnlCur Alm: Clears an abnormal current alarm.
• Clr Cur Imb Alm: Clears a current imbalance alarm.
• ClrAllConvCommF: Clears an “All Converter Comm Fail” alarm.
• ClrConvComm Fail: Clears a converter communication fail alarm.
• Clear Conv Lost: Clears a converter lost alarm.
• ClearSolarLost: Clears a solar converter lost alarm.
• ClrSolarComm Fail: Clears a solar converter communication fail alarm.
Rect Settings Sub-Menu
• Walk-In: Enables or disables the start-up walk-in feature for all rectifiers.
• Walk-In Time: Sets the start-up walk-in time when the “Walk-In” setting above is set to
enabled.
• Start Interval: Sets the sequence start interval (time period between starting each rectifier in
the system).
• Normal Update: Sets rectifier software normal update. When the rectifier is normally
communicating with the controller, the rectifier software is automatically updated as
needed.
• Force Update: Sets rectifier software forced update. When the rectifier is inserted into a
mounting slot, the rectifier software is automatically updated if needed.
Batt Settings Sub-Menu
The BATT SETTINGS sub-menu consists of following sub-menus.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 113

Basic Settings Sub-Menu
• Num Batt Shunts: Sets the number of battery shunts in the system.
• DischAlm Curr: Sets the discharge alarm current value.
NOTE! Only reset the battery capacity when the battery is fully charged; otherwise, the
battery charge status may not be accurate.
Charge Sub-Menu
• Float Voltage(S): Float charge output voltage setting for solar when the “Solar Mode” setting
under “System” TAB in Web Interface is set to either “RECT-SOLAR” or “SOLAR”.
• EQ Voltage(S): Equalize charge output voltage setting for solar when the “Solar Mode”
setting under “System” TAB in Web Interface is set to either “RECT-SOLAR” or “SOLAR”.
• Float Voltage(R): Float charge output voltage setting for rectifier when the “Solar Mode”
setting under “System” TAB in Web Interface is set to “RECT-SOLAR” or “Disabled”.
• EQ Voltage(R): Equalize charge output voltage setting for rectifier when the “Solar Mode”
setting under “System” TAB in Web Interface is set to “RECT-SOLAR” or “Disabled”.
• Curr Limit Mode: Selects the current limit mode (Yes or No).
• Batt Curr Limit: Maximum battery charging current setting. For example, a value of
0.150C10 means that the charging current is limited to 15% of the battery’s nominal
capacity.
• Over Curr Lmt: Battery over current alarm setting. For example, a value of 0.300C10 means
that when the charging current reaches 30% of the battery’s nominal capacity, an alarm will
be extended.
• Auto EQ: Enables or disables the Automatic Equalize Charge feature. The following
parameters need to be set via the Web Interface.
EQ Start Curr: The system is transferred to Equalize Charge mode when battery charge
current increases to this setting. For example, a value of 0.060C10 means that an Automatic
Equalize is started if the battery charge current is greater than 6% of the battery’s nominal
capacity.
EQ Start Cap: The system is transferred to Equalize Charge mode when remaining battery
capacity decreases to this setting.
EQ Stop Curr: When in Equalize Charge mode and the battery charge current decreases
below this setting for the "EQ Stop Delay" time period, the system is transferred to Float
Charge mode. For example, a value of 0.010C10 means that when the charging current is
less than 1% of the battery’s nominal capacity, the system returns to the Float mode.
EQ Stop Delay: See "EQ Stop Curr" above.
NOTE! If the power system has been automatically placed in Equalize mode, disabling Auto
EQ will not return the system to Float mode until the current Equalize cycle is completed. To
return immediately to Float mode, navigate as follows: Main Menu / Settings Icon /
Maintenance / “EQ/FLT Control”, and select Float Charge.
Maximum EQ Time: This is the maximum duration, in minutes, that an Automatic Equalize
Charge will last regardless of the other settings.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 114

 Cyc EQ: Enables or disables cyclic (scheduled) Equalize charging. When enabled, the
following parameters can be set.
Cyc EQ Interval: Cyclic (scheduled) Equalize charging interval.
Cyc EQ Duration: Cyclic (scheduled) Equalize charging duration.
• Hybrid Mode: Refer to Hybrid Control Function (Supporting Generator, Solar and Wind
Energy Input, and Optimization) for more information on the hybrid mode.
• Disabled/ Diesel +AC/ Only Diesel: Sets the hybrid mode or disables the function.
• CycBC Interv: Cyclic (scheduled) Boost charging interval.
• CycBC Start: Cyclic (scheduled) Boost charging start time.
• CycBC End: Cyclic (scheduled) Boost charging end time.
Battery Test Sub-Menu
• Test Volt Level: System output voltage setting during a battery discharge test.
• End Test Volt: This is the “end of test voltage level” for battery discharge tests. A battery
discharge test will end if battery voltage decreases to this setting.
• End Test Time: This is the "end of test time period” for battery discharge tests. A battery
discharge test will end if this time period is exceeded.
• EndTestCapacity: This is the "end of test remaining battery capacity” for battery discharge
tests. A battery discharge test will end if remaining battery capacity decreases to this
setting. For example, a value of 0.700C10 means that when the discharging current reaches
70% of the battery’s nominal capacity, the battery test is ended.
• RecordThreshold: Every time the battery voltage is changed more than this threshold, a new
line is stored in the battery test log.
Temp Comp Sub-Menu
• TempComp Sensor: Select "None" for no temperature compensation, or the temperature
probe (System T1, System T2, System T3, IB2-1 T1, IB2-1 T2, IB2-2 T1, IB2-2 T2, EIB-1 T1, EIB-
1 T2, EIB-2 T1, EIB-2 T2, SMTemp1 T1, …, SMTemp1 T8, SMTemp8 T1, …, SMTemp8 T8)
sensing battery temperature for temperature compensation. You can also select Maximum
or Average which takes the maximum or average reading of the temperature probes (any of
System T1, System T2, System T3, IB2-1 T1, IB2-1 T2, IB2-2 T1, IB2-2 T2, EIB-1 T1, EIB-1 T2,
EIB-2 T1, EIB-2 T2, SMTemp1 T1, …, SMTemp1 T8, SMTemp8 T1, …, SMTemp8 T8) set as
battery temperature probes. When used with an SM-BRC, you can select to average the SM-
BRC temperature probe readings (Average SMBRC setting).
NOTE! The temperature compensation sensor is also the sensor which displays the battery
temperature on the Web Interface’s Homepage.
• TempComp Center: Sets the temperature at which the system operates at normal voltage
levels.
• Temp Comp Coeff: Sets the temperature compensation slope or rate of change per °C above
or below the "TempComp Center" setting. This value is expressed in millivolt per °C per
string (mV/°C/str). For example, for a rate of change of 72 mV/°C/str in a 24-cell 48V
nominal battery string, the rate of change is 3 mV per cell.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 115

Batt1 Settings Sub-Menu
• Shunt Current: Enter the battery string’s shunt current rating.
• Shunt Voltage: Enter the battery string’s shunt voltage rating.
• Rated Capacity: Enter the battery string’s rated capacity. After setting the battery capacity,
the User should also reset the battery capacity (battery must be fully charged). See “Setting
Battery Capacity Parameters” on page 42.
Batt2 Settings Sub-Menu
• Shunt Current: Enter the battery string shunt’s current rating.
• Shunt Voltage: Enter the battery string shunt’s voltage rating.
• Rated Capacity: Enter the battery string’s rated capacity. After setting the battery capacity,
the User should also reset the battery capacity (battery must be fully charged). See “Setting
Battery Capacity Parameters” on page 42.
LVD Settings Sub-Menu
• HTD Point: Sets high temperature limit at which LVD1 and/or LVD2 contactors will open
(disconnect) if the HTD1 and/or HTD2 features are enabled. If this temperature is reached, a
disconnect occurs regardless of voltage.
• HTD Recon Point: Sets temperature at which a reconnect will occur following a High
Temperature Disconnect.
• LVD 1: Enables or disables LVD1.
• LVD 1 Mode: Sets LVD1 to disconnect on a voltage or time setpoint.
• LVD 1 Voltage: LVD1 low voltage disconnect setting (when LVD set for voltage).
• LVD1 Recon Volt: LVD1 reconnect setting (when LVD set for voltage).
• LVD 1 Time: The time period before LVD1 disconnection once an AC fail condition occurs
(when LVD set for time).
• HTD 1: Enables or disables the High Temperature 1 Disconnect feature. This feature causes
LVD1 contactors to open (disconnect) if a high temperature event occurs.
• LVD 2: Enables or disables LVD2.
• LVD 2 Mode: Sets LVD2 to disconnect on a voltage or time setpoint.
• LVD 2 Voltage: LVD2 low voltage disconnect setting (when LVD set for voltage).
• LVD 2 Recon Volt: LVD2 reconnect setting (when LVD set for voltage).
• LVD 2 Time: The time period before LVD2 disconnection once an AC fail condition occurs
(when LVD set for time).
• HTD2: Enables or disables the High Temperature 2 Disconnect feature. This feature causes
LVD2 contactors to open (disconnect) if a high temperature event occurs.
AC Settings Sub-Menu
• Nominal AC Volt: Enter the nominal line-to-neutral voltage (single phase rectifier) or
nominal line-to-line voltage (three phase rectifier).
• Mains Fail Alm1: Sets the Mains Fail Alarm 1 value (percent of nominal).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 116

 • Mains Fail Alm2: Sets the Mains Fail Alarm 2 value (percent of nominal).
Corresponding Alarms:
- Phase A Voltage Low 1 (Nominal Minus "Mains Fail Alarm 1 Percent of Nominal)
- Phase A Voltage Low 2 (Nominal Minus " Mains Fail Alarm 2 Percent of Nominal)
- Phase A Voltage High 1 (Nominal Plus " Mains Fail Alarm 1 Percent of Nominal)
- Phase A Voltage High 2 (Nominal Plus "V Mains Fail Alarm 2 Percent of Nominal)
- Phase A used in the example above, Phase B and Phase C are similar.
Sys Settings Sub-Menu
• LCD Language: Select the language the menus are displayed in.
• Keypad Voice: Sets the keypad sound on or off.
• Date: Sets the date. Refer to “Changing the Date and Time” on page 38 for a procedure to
change the date.
• Time: Sets the time. Refer to “Changing the Date and Time” on page 38 for a procedure to
change the time.
• LCD Rotation: Sets the rotation of the text in the menus (allowing the controller to be
mounted in different orientations).
- 0 deg: Display will be in the horizontal position (M830B only).
- 90 deg: Display will be in the vertical position (NCU controller mounted 90 deg
clockwise) (M830B only).
- Big Screen: Setting for M830D only.
• Restore Default: Restores the controller’s default settings.
• Update App: Updates the controller’s application using a USB memory device.
Comm Settings Sub-Menu
• DHCP: The DHCP function allows the controller to acquire an IP address automatically. This
function can only be enabled or disabled via the local display and keypad. If this function is
enabled and the acquisition of an IP address fails, an alarm is generated. If the acquisition of
an IP address is successful, you need to record the IP address automatically acquired by the
controller to access the controller via the Web Interface. This IP address is displayed in the IP
Address field below the DHCP setting in the local display menu (Main Menu / Settings Icon /
Comm Settings).
• IP Address: Sets the controller's IPv4 address. Enter the address in the format
nnn.nnn.nnn.nnn, where
0 ≤ nnn ≤ 255. The address must be a valid address and must not be 255.255.255.255.
• Mask: Sets the controller's IPv4 network netmask. Enter the address in the format
nnn.nnn.nnn.nnn, where
0 ≤ nnn ≤ 255.
• Default Gateway: Sets the controller's IPv4 gateway address. Enter the address in the
format nnn.nnn.nnn.nnn,
where 0 ≤ nnn ≤ 255. This is the address of the gateway of the network on which the
controller resides. The address must be a valid address and must not be 255.255.255.255.
• IPV6 DHCP: The IPV6 DHCP function allows the controller to acquire an IP address
automatically. This function can only be enabled or disabled via the local display and keypad.
If this function is enabled and the acquisition of an IP address fails, an alarm is generated. If

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 117

 the acquisition of an IP address is successful, you need to record the IP address automatically
acquired by the controller to access the controller via the Web Interface. This IP address is
displayed in the IP Address field below the DHCP setting in the local display menu (Main
Menu / Settings Icon / Comm Settings).
• IPV6 Address: Sets the controller's IPv6 address. Enter the address in the format
nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn, nnnn must follow IPv6 address rules.
• IPV6 Prefix: Sets the controller's IPv6 prefix.
• IPV6 Gateway: Sets the controller's IPv6 gateway address. Enter the address in the format
nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn:nnnn, nnnn must follow IPv6 address rules.
• Vian Enable: Enables or disables Vian feature.
• Vian IO: Sets the Vian value.
Other Settings Sub-Menu
• Rect Expansion:
- Inactive: Select this option if this is the only NCU controller in the power system.
- Primary: Select this option if the power system consists of multiple bays with multiple
NCU controllers, and this NCU controller is to be the primary controller. Note that only
one (1) NCU controller can be set as the primary controller.
- Secondary: Select this option if the power system consists of multiple bays with multiple
NCU controllers, and this NCU controller is to be a secondary controller.
Address: If “Secondary” is selected, this menu item appears after an automatic reboot.
Sets the address of an NCU controller set as a secondary controller.
NOTE! When primary or secondary is selected, the NCU will start auto configure. This
process will take more than three (3) minutes.
Primary/Secondary Procedure:
Up to four (4) NCU controllers can be connected together when a power system requires a
greater number of rectifiers than can be controlled by a single NCU controller. One (1)
controller is designated as the primary controller, the others as secondary controllers. The
rectifiers controlled by the secondary controllers are designated as RectifierGroup 2 through
4 in the menus.
NOTE! Changing the Rectifier Expansion setting may take more than three (3) minutes for the
NCU to configure the feature.
1. Connect the NCU controllers in the multiple bays via the RS485 interface.
2. Set one of the NCU controllers as the primary controller via the “Rect Expansion” menu
item in the OTHER SETTINGS menu.
3. Set all other NCU controllers as secondary controllers via the “Rect Expansion” menu
item in the OTHER SETTINGS menu.
4. Set the Address of the NCU controllers set as secondary controllers to 201, 202, or 203
via the “Address” menu item in the OTHER SETTINGS menu. Note that each secondary
controller must be set to a different address.
• Auto Config: Auto configures the controller for the devices connected to it.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 118

 • LCD Display Wizard: Selects to run the Start Wizard after the controller is restarted. Refer to
the next section and Figure 14.
• Start Wizard Now (see Figure 14).
Site Name Sub-Menu
Enter the site name and other site information.
Common Settings Sub-Menu
Date: Sets the date. Refer to “Changing the Date and Time” on page 38 for a procedure
to change the date.
Time: Sets the time. Refer to “Changing the Date and Time” on page 38 for a procedure
to change the time.
Battery Settings Sub-Menu
TempComp Sensor: Select "None" for no temperature compensation, or the
temperature probe (System T1, System T2, System T3, IB2-1 T1, IB2-1 T2, IB2-2 T1, IB2-2
T2, EIB-1 T1, EIB-1 T2, EIB-2 T1, EIB-2 T2, SMTemp1 T1, …, SMTemp1 T8, SMTemp8 T1,
…, SMTemp8 T8) sensing battery temperature for temperature compensation. You can
also select Maximum or Average which takes the maximum or average reading of the
temperature probes (any of System T1, System T2, System T3, IB2-1 T1, IB2-1 T2, IB2-2
T1, IB2-2 T2, EIB-1 T1, EIB-1 T2, EIB-2 T1, EIB-2 T2, SMTemp1 T1, …, SMTemp1 T8,
SMTemp8 T1, …, SMTemp8 T8) set as battery temperature probes. When used with an
SM-BRC, you can select to average the SM-BRC temperature probe readings.
NOTE! The temperature compensation sensor is also the sensor which displays the battery
temperature on the Web Interface’s Homepage.
TempComp Center: Sets the temperature at which the system operates at normal
voltage levels.
Temp Comp Coeff: Sets the temperature compensation slope or rate of change per °C
above or below the "Temp Comp" setting. This value is expressed in millivolt per °C per
string (mV/°C/str). For example, for a rate of change of 72 mV/°C/str in a 24-cell 48V
nominal battery string, the rate of change is 3 mV per cell.
Capacity Settings Sub-Menu
Batt1: Enter the battery string’s rated capacity.
Batt2: Enter the battery string’s rated capacity.
OK to Exit?
Press ESC to end the wizard or press ENT to continue the wizard to enter the following
parameters.
ECO Parameter Sub-Menu
ECO Mode: Enables or disables the Energy Optimization Mode feature for all rectifiers.
When enabled, the following parameters can be set.
ALERT! The Energy Optimization Mode should NOT be used in systems that operate without
batteries.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 119

 Best Oper Point: Percent of full load capacity that the rectifiers operate under in the
Energy Optimization mode.
Fluct Range: If load fluctuation is less than this value, rectifiers are not turned on or off
for Energy Optimization.
Cycle Period: This is the time period that rectifiers are turned on and off to maintain an
equal operating time for all rectifiers in the system.
Rects ON Time: Time all rectifiers are turned on at End of Cycle.
Alarm Settings Sub-Menu
Audible Alarm: Programs the audible alarm feature.
Off: Disables the audible alarm.
On: When a new alarm occurs, the audible alarm sounds. Press any key to silence
the audible alarm.
3 min / 10 min / 1 hr / 4 hrs: When a new alarm occurs, the audible alarm sounds.
The audible alarm automatically silences after the selected time period.
IP Address Sub-Menu
DHCP: The DHCP function allows the controller to acquire an IP address automatically.
This function can only be enabled or disabled via the local display and keypad. If this
function is enabled and the acquisition of an IP address fails, an alarm is generated. If
the acquisition of an IP address is successful, you need to record the IP address
automatically acquired by the controller to access the controller via the Web Interface.
This IP address is displayed in the IP Address field below the DHCP setting in the local
display menu (Main Menu / Settings Icon / Comm Settings).
IP Address: Sets the controller's IP address. Enter the address in the format
nnn.nnn.nnn.nnn, where
0 ≤ nnn ≤ 255. The address must be a valid address and must not be 255.255.255.255.
Mask: Sets the controller's network netmask. Enter the address in the format
nnn.nnn.nnn.nnn, where
0 ≤ nnn ≤ 255.
Default Gateway: Sets the controller's gateway address. Enter the address in the format
nnn.nnn.nnn.nnn,
where 0 ≤ nnn ≤ 255. This is the address of the gateway of the network on which the
controller resides. The address must be a valid address and must not be
255.255.255.255.
• Over Voltage 1: Sets the Over Voltage 1 alarm point.
• Over Voltage 2: Sets the Over Voltage 2 alarm point.
• Under Voltage 1: Sets the Under Voltage 1 alarm point.
• Under Voltage 2: Sets the Under Voltage 2 alarm point.
• Conv Volt Set: Sets the output voltage for all converters.
• System Temp1: Sets system temperature port 1 to None, Battery, or Ambient.
• System Temp 2: Sets system temperature port 2 to None, Battery, or Ambient.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 120

 • IB2-1 Temp 1: Sets temperature port 1 on the IB2-1 board to None, Battery, or Ambient.
• IB2-1 Temp 2: Sets temperature port 2 on the IB2-1 board to None, Battery, or Ambient.
• IB2-2 Temp 1: Sets temperature port 1 on the IB2-2 board to None, Battery, or Ambient.
• IB2-2 Temp 2: Sets temperature port 2 on the IB2-2 board to None, Battery, or Ambient.
• EIB-1 Temp 1: Sets temperature port 1 on the EIB-1 board to None, Battery, or Ambient.
• EIB-1 Temp 2: Sets temperature port 2 on the EIB-1 board to None, Battery, or Ambient.
• EIB-2 Temp 1: Sets temperature port 1 on the EIB-2 board to None, Battery, or Ambient.
• EIB-2 Temp 2: Sets temperature port 2 on the EIB-2 board to None, Battery, or Ambient.
Rect Ctrl Sub-Menu
• AC: Sets the AC status On/Off.
• Ctrl: Sets the control status On/Off
• LED Control: Sets the LED Control status Flash/ Cancel.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 121

WEB INTERFACE SCREENS
Overview of Web Function
This section provides descriptions of the Web Interface Screens. Refer also to “Passwords and
Privilege Levels” on page 25 and “Using the Web Interface” on page 24. For Local Display Menus,
refer to “Local Display Menus” on page 97.
NOTE! Best viewed at 1024 x 768 resolution.

Homepage
In the Web Interface, after entering a valid User Name and Password and clicking LOGIN, the
"Homepage" window opens. See also “Logging into the Controller” on page 34.

Figure 19: NCU Homepage

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 122

Figure 20: NCU Homepage with Solar Converters

The homepage window is divided into six areas:

1. System Status Information Area
2. System Specifications Information Area
3. Controller Specifications Information Area
4. Alarms Area
5. System Status Area
6. Menu Navigation Area

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 123

System Status Information Area
Output voltage and output current are displayed here.

System Specifications Information Area

System specifications are displayed here.

Controller Specifications Information Area

Controller specifications are displayed here.

Site Information Area

Site information is displayed here.

Figure 21: System Status Information, System Specifications Information, Controller Specifications
Information, and Site Information Areas

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 124

Alarms Area
Any alarms active in the power system are shown in this area.
• When viewing the Alarm List, click the “arrow” icon to collapse the Alarm List. Click the
"arrow" icon again to expand the Alarm List.
• The alarms area contains tabs to allow viewing all alarms or a type of alarm (severity). For
example, click the Critical tab to display alarms set as Critical alarms.
• When the “Auto Popup” box is checked and the Alarm List is collapsed, a new alarm will
cause the Alarm List to expand.
NOTE! Minor alarms are shaded yellow, major alarms are shaded orange, and critical alarms
are shaded red.

Figure 22: Alarms Area

Arrow Icon Alarm Severity Tabs or All Alarms“Auto Popup” Box

Alarm List Collapsed

Alarm List Expanded

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 125

System Status Area
System status is displayed in this area and consists of a Power System tab, Energy Sources tab (if
additional energy sources are connected to the system), and a General Status tab.
Temperature Reading
• The temperature sensor set as “Ambient Temp Sensor” (Settings Menu / System Tab) is the
sensor which displays the ambient temperature on the Power System tab.
System Current Reading
• “System Current” equals total rectifier current or total solar converter current minus total
battery current when battery shunt exists or calculated battery current. If you do not
calculate battery current, “System Current” equals total rectifier current or total solar
converter current.
Power System Tab
The Power System tab displays power system status in a graphical block diagram format. This
includes status of the input power, modules (i.e. rectifiers, solar converters, converters), DC
equipment, and battery. Also displayed are alarm status, ambient temperature, output voltage,
output current, average current, and a load trend chart.

Figure 23: Power System Tab Calculated

Load
Current

Temperatur
e Reading

System
Current
Reading

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 126

The power system status area is User interactive. Clicking on the various icons will take you to that
devices status Web page. For example, clicking on the rectifier module icon opens the following
Web page. This topic is further explained in the next section.

Figure 24: Rectifier Module Status Web Page

Device Group Status Pages

The power system status block diagram has interactive links. Clicking on a link takes you to that
device group’s status page. A device group’s status page displays current or logged operating
parameters for that device group.
The following sections describe the Module (i.e. rectifier, converter, solar converter), DC, and the
Battery device groups as samples of how to use these links.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 127

Figure 25: Power System Status Page Block Diagram

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 128

Module (Rectifier, Converter, Solar Converter) Device Group Status Page
Clicking on a rectifier, converter, or solar converter icon on the power system status block diagram
opens up the status page for the module’s Device Group. The Module Device Group status page
contains multiple tabs (depending on the modules installed in your power system). This includes
Rectifier, Converter, and Solar Converter tabs.

Rectifier Device Group Status Page Tab

This tab displays status values such as “Total Current”, “Number of Rectifiers”, etc.

Figure 26: Rectifier Device Group Status Page Tab

Individual Rectifier Status Page

Displayed on the Rectifier Device Group status page are the individual rectifiers installed in the
system. Click on an individual rectifier icon to display its status such as "Current Limit", etc.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 129

Figure 27: Individual Rectifier Status Page

Individual Rectifier Settings Page

In the Rectifier Device Group Status Page Tab, click the settings wheel icon to go to the
individual rectifier settings page. Click to go back to the Rectifier Device Group Status
Page Tab.

Figure 28: Selecting an Individual Rectifier Settings Page

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 130

Figure 29: Individual Rectifier Settings Page

NOTE! Settings that appear "grayed out" can only be made when the controller is in the
"manual control" state. If the controller is set for "automatic" control, change the
“Auto/Manual State” setting first to the “Manual” setting.
• DC On/Off Control: Temporarily turns the rectifier’s DC output on or off when the controller
is in Manual mode. Setting returns to original when controller is returned to the Auto mode.
• AC On/Off Control: Temporarily turns the rectifier’s AC input on or off when the controller is
in Manual mode. Setting returns to original when controller is returned to the Auto mode.
• LED Control: Temporarily sets whether or not the rectifier's local power indicator blinks
when the controller is communicating with the rectifier when the controller is in Manual
mode. Setting returns to original when controller is returned to the Auto mode.
• Rectifier Reset: Temporarily sets the rectifier’s over voltage reset feature when the
controller is in Manual mode. Setting returns to original when controller is returned to the
Auto mode.
• Rectifier ID: Sets the rectifier’s identification number.
• Rectifier Phase: Indicates the phase connected to the rectifier’s input.
Solar Converter Device Group Status Page Tab
This tab displays status values such as “Total Current”, “Number of Solar Converters”, etc.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 131

Figure 30: Solar Converter Device Group Status Page Tab

Individual Solar Converter Status Page

Displayed on the Solar Converter Device Group status page are the individual solar converters
installed in the system. Click on an individual solar converter icon to display its status such as
"Input Current", "Output Power", etc.

Figure 31: Individual Solar Converter Status Page

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 132

Individual Solar Converter Settings Page
In the Solar Converter Device Group Status Page Tab, click the settings wheel icon to go to the
individual solar converter settings page. Click to go back to the Solar Converter Device
Group Status Page Tab.

Figure 32: Selecting an Individual Solar Converter Settings Page

Figure 33: Individual Solar Converter Settings Page

NOTE! Settings that appear "grayed out" can only be made when the controller is in the
"manual control" state. If the controller is set for "automatic" control, change the
“Auto/Manual State” setting first to the “Manual” setting.
• DC On/Off Control: Temporarily turns the solar converter’s DC output on or off when the
controller is in Manual mode. Setting returns to original when controller is returned to the
Auto mode.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 133

 • LED Control: Temporarily sets whether or not a solar converter's local power indicator blinks
when the controller is communicating with the solar converter when the controller is in
Manual mode. Setting returns to original when controller is returned to the Auto mode.
• Solar Converter Reset: Temporarily sets the solar converter’s over voltage reset feature
when the controller is in Manual mode. Setting returns to original when controller is
returned to the Auto mode.
• Solar Converter ID: Sets the solar converter’s identification number.
Converter Device Group Status Page Tab
This tab displays status values such as “Total Current”, “Number of Converters”, etc.

Figure 34: Converter Device Group Status Page Tab

Individual Converter Status Page

Displayed on the Converter Device Group status page are the individual converters installed in the
system. Click on an individual converter icon to display its status such as "Current", etc.

Figure 35: Individual Converter Status Page

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 134

Individual Converter Settings Page
In the Converter Device Group Status Page Tab, click the settings wheel icon to go to the
individual converter settings page. Click to go back to the Converter Device Group Status
Page Tab.

Figure 36: Selecting an Individual Converter Settings Page

Figure 37: Individual Converter Settings Page

NOTE! Settings that appear "grayed out" can only be made when the controller is in the
"manual control" state. If the controller is set for "automatic" control, change the
“Auto/Manual State” setting first to the “Manual” setting.
• DC On/Off Control: Temporarily turns the converter’s DC output on or off when the
controller is in Manual mode. Setting returns to original when controller is returned to the
Auto mode.
• Converter Reset: Temporarily sets the converter’s over voltage reset feature when the
controller is in Manual mode. Setting returns to original when controller is returned to the
Auto mode.
• LED Control: Temporarily sets whether or not a converter's local power indicator blinks
when the controller is communicating with the converter when the controller is in Manual
mode. Setting returns to original when controller is returned to the Auto mode.
• Converter ID: Sets the converter’s identification number.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 135

DC Device Group Status Page
Clicking on the DC icon on the power system status block diagram opens up the status page for the
DC Device Group. The DC Device Group status page contains multiple tabs (depending on the DC
equipment installed in your power system). This includes DC, SMDU, SMDUP, EIB and Cabinet Map.
The DC status page tab is shown next for an example.
DC Status Tab
This tab displays status values such as "DC Voltage”.

Figure 38: DC Device Group Status Tab

Cabinet Map Status Tab (if available)

This tab displays the number of distribution cabinets in the system and the DUs in each distribution
cabinet.

Figure 39: Cabinet Map Status Tab (if available)

Example: Clicking on DU 2.2 in the Cabinet Map Status screen shown in Figure 39 displays Figure
40. Figure 40 shows there are two (2) branch circuits in DU2.2 and the current of the branch circuit
is 0 A.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 136

Figure 40: Branch Current in DU Screen

Battery Device Group Status Page

Clicking on the battery icon on the power system status block diagram opens up the status page for
the Battery Device Group. The Battery Device Group status page displays battery status values such
as "Battery Management State" and "Battery Temp". The actual display of the Battery Device
Group status page is dependent on the NCU configuration and if SMDU or EIB shunts are
programmed as battery shunts (see Figure 41 and Figure 42 for samples).

Figure 41: Battery Device Group Status Page

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 137

Figure 42: Battery Device Group Status Page

Individual Battery Status Page

Displayed on the Battery Device Group status page are the individual batteries installed in the
system. Hover the mouse over an individual battery icon to display its status such as "Battery
Rating". The actual display of an Individual Battery status page is dependent on the NCU
configuration and if SMDU or EIB shunts are programmed as battery shunts (see Figure 43 and
Figure 44 for samples).

Figure 43: Individual Battery Status Page

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 138

Figure 44: Individual Battery Status Page

Individual Battery Capacity Trend Diagram or Info Screen

Displayed on the Battery Device Group status page are the individual batteries installed in the
system. Click on an individual battery (Battery 1 or Battery 2) to display its "Capacity Trend
Diagram" or “info screen”. The actual display of an individual battery capacity trend diagram or
info screen is dependent on the NCU configuration. （See Figure 45 for sample)

Figure 45: Individual Battery Capacity Trend Diagram

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 139

Individual Battery Settings Page

In the Battery Device Group Status Page Tab, click the settings wheel icon to go to the individual
battery settings page. See Figure 46. Click to go back to the Battery Device Group Status
Page Tab. The actual display of an Individual Battery status is dependent on the NCU configuration
and if SMDU or EIB shunts are programmed as battery shunts (see Figure 47, Figure 48, and Figure
49.)

Figure 46: Selecting an Individual Battery Settings Page

Figure 47: Individual Battery Settings Page (Battery #)

• Battery Management: Select Yes to use the battery management feature and No to not use
the feature for this battery.
• Rated Capacity: Enter the battery string's rated capacity.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 140

 • Shunt Current: Enter the battery string's shunt current rating.
• Shunt Voltage: Enter the battery string's shunt voltage.
• Current Break Size: Enter the threshold value of current alarm.
• Current High1 Current Limit: Enter the high current limit point of current1.
• Current High2 Current Limit: Enter the too high current limit point of current1.

Figure 48: Individual Battery Settings Page (SMDU#Battery #)

Figure 49: Individual Battery Settings Page (EIB-#Battery #)

Battery Management: Select Yes to use the battery management feature and No to not use the
feature for this battery.
Rated Capacity: Enter the battery string's rated capacity.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 141

Energy Sources Status Tab
The Energy Sources Status tab displays a chart of the different energy sources available during a
selected time period.

Figure 50: Energy Sources Status Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 142

Consumption Map Tab
The Consumption Map tab displays the customers whose loads are being monitored for
consumption in a grid list of customer load icons. Click the " " symbol in a load icon to display the
consumption details for that customer.
Each load icon shows the customer name and total current.
Green Icon: Customer load current is in normal state.
Yellow Icon: Customer load current is larger than Alarm Level 1.
Red Icon: Customer load current is larger than Alarm Level 2.
Grey Icon: Customer load current is 0.
White Icon: Customer load has not been configured.

Figure 51: Consumption Map Tab

User Define Tab

The User Define Status tab displays user defined status entries.

Figure 52: User Define Status Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 143

Menu Navigation Area
Available menus are displayed in this area. When a menu is clicked on, the system status screen is
replaced with the selected menu’s screen. Note that there is a menu item named HOME to return
to the system status screen.
Located at the top of each main menus are tabs to select the various sub-menus. If there are more
sub-menus then can be displayed in the window, an arrow appears to navigate to the additional
sub-menus. An orange “arrow” icon indicates there are additional tabs. Click the orange "arrow"
icon to view the additional tabs.

Figure 53: Menu Navigation Area

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 144

Settings Menu
The Settings Menu allows you to change (if you have the proper privilege level programmed in your
User settings) the settings of the various programmable parameters. Settings are grouped per
function. Select a tab in the Settings Menu to change that function’s programmable parameters.

Figure 54: Settings Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 145

Changing Programmable Parameters in the Settings Menu
To change a programmable parameter, select or enter a new value for the parameter then click on
“Set” to change the value.
NOTE! Settings that appear "grayed out" can only be made when the controller is in the
"manual control" state. If the controller is set for "automatic" control, change the
“Auto/Manual State” setting first to the “Manual” setting.

Quick Settings Tab Programmable Parameter Descriptions

• Site Settings: Enter a "Site Name", "Site Location", and "System Name".
• Time Settings: Enter the time or select "Get Local Time from Connected PC".
In the Time Settings section, click on "Get Local Time from Connected PC" and then “Set” to
automatically set the date and time. To manually set the date and time, click on “the clock
symbol” and enter the date and time. Then select the “Confirm” button. See Figure 55. In
the Time Settings section, click on “Set” to save the change.

Figure 55: Manual Date and Time Menu

• Signal Settings:
- Float Charge Voltage: Float Charge output voltage setting.
- Equalize Charge Voltage: Equalize Charge output voltage setting.
- Temp Compensation Probe Number: Select "None" for no temperature compensation,
or the temperature probe [System Temp1 (bat), System Temp2 (bat), System Temp3
(bat), IB2-1 Temp1 (bat), IB2-1 Temp2 (bat), IB2-2 Temp1 (bat), IB2-2 Temp2 (bat), EIB-1

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 146

 Temp1 (bat), EIB-1 Temp2 (bat), EIB-2 Temp1 (bat), EIB-2 Temp2 (bat), SMTemp1 Temp1
(bat), …, SMTemp1 Temp8 (bat), SMTemp8 Temp1 (bat), …, SMTemp8 Temp8 (bat)]
sensing battery temperature for temperature compensation. You can also select
Maximum or Average which takes the maximum or average reading of the temperature
probes [any of System Temp1 (bat), System Temp2 (bat), System Temp3 (bat), IB2-1
Temp1 (bat), IB2-1 Temp2 (bat), IB2-2 Temp1 (bat), IB2-2 Temp2 (bat), EIB-1 Temp1
(bat), EIB-1 Temp2 (bat), EIB-2 Temp1 (bat), EIB-2 Temp2 (bat), SMTemp1 Temp1 (bat),
…, SMTemp1 Temp8 (bat), SMTemp8 Temp1 (bat), …, SMTemp8 Temp8 (bat)] set as
battery temperature probes. When used with an SM-BRC, you can select to average the
SM-BRC temperature probe readings (Average SMBRC setting).
- Temp Comp Coefficient (slope): Sets the temperature compensation slope or rate of
change per °C above or below the "Temperature Compensation Center" setting. This
value is expressed in millivolt per °C per string (mV/°C/str). For example, for a rate of
change of 72 mV/°C/str in a 24-cell 48V nominal battery string, the rate of change is 3
mV per cell.
- Temperature Compensation Center: Sets the temperature at which the system operates
at normal voltage levels.
ALERT! The Energy Optimization Mode should NOT be used in systems that operate without
batteries.

- ECO Mode: Enables or disables the Energy Optimization Mode feature for all rectifiers.
When enabled, the following parameters can be set.
Best Operating Point: Percent of full load capacity that the rectifiers operate under in the
Energy Optimization Mode.
Load Fluctuation Range: If load fluctuation is less than this value, rectifiers are not
turned on or off for Energy Optimization.
Cycle Period: This is the time period that rectifiers are turned on and off to maintain an
equal operating time for all rectifiers in the system.
All Rects ON Time: Time all rectifiers are turned on at the end of the “Cycle Period”.
- Outgoing Alarms Blocked:
Normal: Alarms are processed normally.
Blocked: Forces the alarm relays in the "off" state and blocks alarms from changing the
relay state.
- Batt1 Rated Capacity: Enter the battery string’s rated capacity.
- Batt2 Rated Capacity: Enter the battery string’s rated capacity.
- SMDU1Batt2 Rated Capacity: Enter the battery string’s rated capacity.
Set Cabinet Tab Programmable Parameter Descriptions
The Set Cabinet tab is shown in Figure 56.
The Set Cabinet tab is divided into two parts. The left part is the load branch list, which will be used
to designate the customer load branch circuits to be monitored for consumption. The right part is
the customer load icons displayed in a grid list.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 147

 Figure 56: Set Cabinet Tab

Load branch list

Customer load icons displayed in a grid list

Click this symbol to set the customer

load(s) being monitored alarm thresholds

Click this symbol to set the load branch circuit current rating

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 148

Setting the Load Branch Circuit Current Rating
1. Click the symbol next to the load branch circuit to be set. See Figure 57.

Figure 57: Setting the Load Branch Circuit Current Rating-1

Click this symbol to set the load branch circuit current rating

2. The following window opens. Enter a value for the branch circuit current rating and click Set.

Figure 58: Setting the Load Branch Circuit Current Rating-2

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 149

 Setting the Customer Icons Parameters
1. Click the symbol next to the customer icon to be set. See Figure 59.

Figure 59: Setting the Customer Icons Parameters-1

Click this symbol to set

the customer icon
parameters.

2. The following window opens. Enter the customer icon parameters and click Set.
• Name: The name of the customer.
• Alarm Level 1: If the customer load(s) exceeds the percent of the total branch circuit current
rating entered for Alarm Level 1, the icon representing the customer load turns yellow, which
indicates an observation alarm.
• Alarm Level 2: If the customer load(s) exceeds the percent of the total branch circuit current
rating entered for Alarm Level 2, the icon representing the customer load turns red, which
indicates a major alarm.
• Rated Power: Sets the rated power of the cabinet.

Figure 60: Setting the Customer Icons Parameters-2

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 150

Designating the Load Branch Circuits Connected to Each Customer’s Loads to be Monitored for Consumption
1. Select a customer load icon in the grid list by clicking on its icon.

Figure 61: Selecting a Customer Load Icon in the Grid List

Select a customer load icon

in the grid list by clicking on
its icon.

2. Click the "Show Designation" button. The following widow opens.

Figure 62: Show Designation Window

3. Select a Cabinet and a DU in the drop-down list boxes. The available load distribution branch
circuits are displayed as shown in the following window. Drag one of the displayed load
distribution branch circuits from the left side to the selected customer load icon in the grid list
displayed on the right side. Once a load distribution branch circuit has been designated, it will
become greyed out and cannot be dragged again. You can add up to twenty (20) load
distribution branch circuits to a customer load icon.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 151

Figure 63: Dragging Branch to the Selected Grid

Select a Cabinet
and a DU in the
drop-down list
boxes. Drag a load distribution branch circuit
onto a customer icon.

4. Click the "Designate" button to set the designation.

System Tab Programmable Parameter Descriptions
Power System
Relay Output 14 (15, 16, 17): Temporarily sets the relay open or closed in manual mode. Setting
reverts to original when controller is returned to the Auto mode.
Clear Maintenance Run Time: In manual mode, the only selection for "Clear Maintenance Run
Time" is Yes. Once Yes is selected and confirmed, the Power System's Maintenance Run
Time log is cleared.
Auto/Manual State:
Auto: The controller automatically controls the power system.
Manual: A User can manually change certain power system control settings. This provides a
convenient means of making temporary adjustment changes for testing purposes.
Manual Mode Time Limit: Sets time limit in manual mode.
With FCUP: Whether there is FCUP.
Maintenance Cycle Time: The maintenance cycle time is the number of days before a
Maintenance Alarm is issued.
LCD Rotation: Sets the rotation of the text in the menus (allowing the controller to be mounted
in different orientations).
0 deg: Display will be in the horizontal position (M830B only).
90 deg: Display will be in the vertical position (NCU controller mounted 90 deg clockwise)
(M830B only).
Big Screen: Setting for M830D only.
Slave Current Limit Value: Current limit point for power system designated as the slave system
in a "Power Split" configuration.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 152

 Delta Voltage: The offset voltage that the power system designated as the slave system in a
"Power Split" configuration is set to. It is suggested to leave this value at the default (0.5
volts).
Over Load Alarm Point: Sets the over load alarm point, the settable point starts from 50%.
Imbalance Protection: When the calculated load current is a negative value (Usually this
condition happens when battery current is measured incorrectly due to wrong setting of
battery shunt). Enables "Imbalance Protection", the controller will disable battery
management functions and force the system to enter the float charging status.
Relay Reporting: Relay 6, Relay 7, Relay 8 are for relay reporting.
Fixed: Relay 6 is for NCU running, Relay 7 is for "Observation Alarm", and Relay 8 is for "Major/
Critical Alarm".
User Defined: User can define different relay functions.
Outgoing Alarms Blocked:
Normal: Alarms are processed normally.
Blocked: Forces the alarm relays in the "off" state and blocks alarms from changing the relay
state.
Rectifier Expansion
Inactive: Select this option if this is the only NCU controller in the power system.
Primary: Select this option if the power system consists of multiple bays with multiple NCU
controllers and this controller is to be the primary controller. Only one NCU controller can
be set as the primary controller.
NOTE! When primary is selected, the NCU will start auto configuring. This process will take
more than three (3) minutes.
Secondary: Select this option if the power system consists of multiple bays with multiple
NCU controllers and this controller is to be a secondary controller.
ALERT! DO NOT set the controller to Secondary from the Web Interface. You will not be able
to log into the controller after it automatically reboots into secondary mode. Controllers to
be designated as secondary controllers need to be set locally via the local keypad and
display.
Primary/Secondary Procedure:
Up to four (4) NCU controllers can be connected when a power system requires a greater number
of rectifiers than can be controlled by a single NCU controller. One (1) controller is designated as
the primary controller, the others as secondary controllers. The rectifiers controlled by the
secondary controllers are designated as Rectifier Group 2 through 4 in the menus.
NOTE! Changing the Rectifier Expansion setting may take more than 3 minutes for the NCU
to configure the feature.
1. Connect the NCU controllers in the multiple bays via the RS485 interface.
2. Set one of the NCU controllers as the primary controller.
3. Set all other NCU controllers as secondary controllers.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 153

 ALERT! DO NOT set the controller to Secondary from the Web Interface. You will not be able
to log into the controller after it automatically reboots into secondary mode. Controllers to
be designated as secondary controllers need to be set locally via the local keypad and
display.
4. Set the address of the NCU controllers set as secondary controllers to 201, 202, or 203. Note
that each secondary controller must be set to a different address.
Lower Consumption: Enables or disables energy saving mode.
Power Peak Savings: Enables or disables the limitation of maximum power.
MPCL Pwr Range: Maximum power consumption limit has a power range, if the power is
higher/lower than the highest / lowest point, it will go back to the range.
MPCL Battery Discharge On: Enables or disables the maximum power consumption limit battery
discharge.
MPCL Diesel Control On: Enables or disables the maximum power consumption limit diesel
control.
Converter Only: Enables or disables the converter only function.
SMDU-EIB Mode
Normal: Doesn't use load shunt to calculate load current.
Load Switch: Uses load shunt to sample load current.
Over Voltage 1: Sets the Over Voltage 1 alarm point.
Over Voltage 2: Sets the Over Voltage 2 alarm point.
Under Voltage 1: Sets the Under Voltage 1 alarm point.
Under Voltage 2: Sets the Under Voltage 2 alarm point.
Fail Safe Mode: When enabled, sets the relay designated as the "Critical Summary" alarm relay
to operate in the "fail safe" mode. In this mode, the relay is energized during normal
operation and de-energized for an alarm condition.
Hybrid Mode: Refer to Hybrid Control Function (Supporting Generator, Solar and Wind Energy
Input, and Optimization) for more information on the hybrid mode.
Disabled/ Fixed Daily/ Capacity: Sets the hybrid mode or disables the function.
PowerSplit Contactor Mode: Enables or disables the power split feature ("master control"
indicates the NCU system operates normally and "slave control" indicates the NCU system is
a slave system of the existing legacy system).
Bad Grid to Grid: Recover the unstable AC power.
Bad Grid Delay Time: The unstable AC power delay time.
Bad Grid Soc Threshold: The threshold of unstable AC power capacity.
DG Warmup Enabled: When switching to DG mode, start the DG first and then add the load.
DG Cooldown Enabled: When switching to AC mode, close the DG first and then add the load.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 154

 Ambient Temp Sensor: Sets the temperature sensor which displays the ambient temperature on
the Web Interface's Homepage. Note that this temperature sensor must be set as an
ambient temperature sensor. Select "None", or the temperature probe
(SMTemp8T8/.../SMTemp8T1/.../SMTemp1T1/EIBT2/IB2T2/IB2T1). You can also select
Maximum or Average which takes the maximum or average reading of the temperature
probes (any of SMTemp8T8/.../ SMTemp8T1 / .../SMTemp1T8/.../SMTemp1T1/EIB T2/EIB
T1/ IB2 T2/ IB2 T1) set as ambient temperature probes.
Ambient Temp High1: Sets the ambient temperature high 1 alarm point.
Ambient Temp Low: Sets the ambient temperature low alarm point.
Ambient Temp High2: Sets the ambient temperature high 2 alarm point.
DI9 Alarm State through DI 12 Alarm State: Choose high/low for digital input alarm state.
System Temp 1 through System Temp 3: Choose none / ambient / battery sensor for system
temperature sensor. When " ambient " is selected, following alarm points can be set.
System Temp1 High 2: Sets the system temperature 1 high 2 alarm point.
System Temp1 High 1: Sets the system temperature 1 high 1 alarm point.
System Temp1 Low: Sets the system temperature 1 low alarm point.
IB2 Temp 1 through IB2 Temp 3: Choose none / ambient / battery sensor for IB2 temperature
sensor. When " ambient " is selected, following alarm points can be set.
IB2 Temp1 High 2: Sets the IB2 temperature 1 high 2 alarm point.
IB2 Temp1 High 1: Sets the IB2 temperature 1 high 1 alarm point.
IB2 Temp1 Low: Sets the IB2 temperature 1 low alarm point.
EIB Temp 1 through EIB Temp 2: Choose none / ambient / battery sensor for EIB temperature
sensor.
EIB Temp1 High 2: Sets the EIB temperature 1 high 2 alarm point.
EIB Temp1 High 1: Sets the EIB temperature 1 high 1 alarm point.
EIB Temp1 Low: Sets the EIB temperature 1 low alarm point.
Auto Mode: Sets auto mode as normal or EMEA mode.
Normal: The controller does not remember the new settings made in manual mode. When the
controller returns to auto mode, the settings revert to the default settings.
EMEA: In EMEA mode, the controller remembers the new settings made in manual mode.
DO14(15, 16,17) Normal State: The normal state of DO14,15,16,17 is Non-Energized or
Energized.
Relay Test: Choose disable / individual / automatic for relay test.
Relay Test Time: Sets the relay test time from 5 sec to 120 sec.
Converter Voltage Level: Choose 48 V system or 24 V system for converter voltage level.
Hybrid Mode: Choose enables or disables the hybrid mode.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 155

 Cyclic BC Interval: Cyclic (scheduled) Boost charging interval.
Cyclic BC Start Time: Sets cyclic (scheduled) Boost charging start time.
Cyclic BC End Time: Sets cyclic (scheduled) Boost charging end time.
High Load Level 1: Sets the high load level 1 alarm point (alarm point for total rectifier load).
High Load Level 2: Sets the high load level 2 alarm point (alarm point for total rectifier load).
CB Threshold Value: If the load current of a branch circuit increases above the product of [“load
branch circuit current rating” times the CB Threshold Value], the branch current column in
the DU screen (Figure 40) turns yellow, which indicates an observation alarm. (Refer to
Setting the Load Branch Circuit Current Rating on page 149.)
CB Overload Value: If the load current of a branch circuit increases above the product of [“load
branch circuit current rating” times the CB Overload Value], the branch current column in the
DU screen (Figure 40) turns red, which indicates a major alarm. (Refer to Setting the Load
Branch Circuit Current Rating on page 149.)
Cab X Num (Valid After Reset): The cabinet number of X axis.
Cab Y Num (Valid After Reset): The cabinet number of Y axis.
Solar Mode: Sets solar mode as disabled, rect-solar, or solar mode.
Running Way (For Solar): Sets rect first or solar first for solar mode running way.
Adjust Bus Input Voltage: Sets adjust bus input voltage from 19 V to 60 V.
Time Display Format: Sets time display format as EMEA, NA, CN.
AC Equipment
Rectifier AC
Nominal Phase Voltage: Enter the nominal line to neutral voltage (single phase rectifier) or
nominal line to line voltage (three phase rectifier).
Mains Failure Alarm Limit 1: Sets the mains fail alarm 1 value (percent of nominal).
Mains Failure Alarm Limit 2: Sets the mains fail alarm 2 value (percent of nominal).
Corresponding Alarms:
Phase A Voltage Low 1 (Nominal Minus "Mains Failure Alarm 1” Percent of Nominal)
Phase A Voltage Low 2 (Nominal Minus " Mains Failure Alarm 2” Percent of Nominal)
Phase A Voltage High 1 (Nominal Plus " Mains Failure Alarm 1” Percent of Nominal)
Phase A Voltage High 2 (Nominal Plus "V Mains Failure Alarm 2” Percent of Nominal)
Phase A used in the example above, Phase B and Phase C are similar.
DC Equipment (DC)
Shunt Current: Enter the load shunt's current rating.
Shunt Voltage: Enter the load shunt's voltage rating.
Load Shunt Exist: Selects whether a load shunt exists or not.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 156

LVD Group
NOTE! HTD Reconnect Point and HTD Point require a BTRM sensor. The BTRM sensor is the
sensor which is used for the High Temperature Disconnect (HTD) Feature.
HTD Reconnect Point: Sets temperature at which a reconnect will occur following a high
temperature disconnect.
HTD Point: Sets high temperature limit at which LVD1 and/or LVD2 contactors will open
(disconnect) if the HTD1 and/or HTD2 features are enabled. If this temperature is reached, a
disconnect occurs regardless of voltage.
AC Fail Required (LVD Needs AC Fail): Enables or disables whether the contactor opens during
an AC failure.
LVD3 Enable: Enables or disables LVD3.
Relay for LVD3: Selects relay for LVD3.
Fuel Group
Fuel Tank Group
Fuel Number: Sets the fuel number.
OB Fuel Number: Sets the OB fuel number.
EIB Equipment
EIB 1
Shunt # Set As (Not Used, General, Load, Battery):
Not Used: Indicates this shunt input is not used.
General: Indicates the measurement of the shunt will be displayed and will not be added to
Total DC Load or Total Battery Load.
Load: Indicates the measurement of the shunt will be displayed and added to the Total DC
Load.
Battery: Indicates the measurement of the shunt will be displayed and added to the Total
Battery Load and used with Battery Management.
Shunt # Full Current: Enter the shunt’s current rating.
Shunt # Full Voltage: Enter the shunt’s voltage rating.
Voltage Type: The EIB assembly provides a total of eight (8) DC voltage inputs for battery block
monitoring.
24 (Block 2): Selects the EIB to monitor up to four (4) 24V battery strings with two (2) 12V
blocks per string.
48 (Block 4): Selects the EIB to monitor up to two (2) 48V battery strings with four (4) 12V
blocks per string.
Mid Point: Selects the EIB to monitor the midpoint voltage of up to eight (8) battery strings
for either 24V or 48V systems.
Disabled: Disables the battery block monitoring feature.
Block In-Use Num: Number of 12 V battery blocks being used.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 157

 Block Voltage Diff (12V): This menu item appears if “24 (Block 2)” or “48 (Block 4)” is selected
above. The “Block Voltage Diff (12V)” setting selects the alarm threshold for battery block
monitoring. The NCU issues an alarm when any block voltage of any battery string has an
abnormal value. The alarm is issued when the difference between any block voltage and a
reference voltage is greater than the value of the block voltage difference setting.
Block Voltage Diff (Mid): This menu item appears if “Mid-Point” is selected above. The “Block
Voltage Diff (Mid)” setting selects the alarm threshold for battery midpoint monitoring. The
NCU issues an alarm when any battery midpoint voltage of any battery string has an
abnormal value. The alarm is issued when the difference between any battery midpoint
voltage and a reference voltage is greater than the value of the block voltage difference
setting.
OBLVD Equipment
LVD Unit
LVD1: Enables or disables LVD1.
LVD1 Mode: Sets LVD1 to disconnect on a voltage or time setpoint.
LVD1 Voltage: LVD1 low voltage disconnect setting (when LVD set for voltage)
LVD1 Reconnect Voltage: LVD1 reconnect setting (when LVD set for voltage).
LVD1 Reconnect Delay: Delay time until LVD1 reconnects once voltage recovers (when LVD set
for voltage).
LVD1 Time: The time before LVD1 disconnection once an AC fail condition occurs (when LVD set
for time).
LVD1 Dependency: Select if LVD1 can disconnect only if LVD2 or LVD3 has disconnected, or none.
LVD2: Enables or disables LVD2.
LVD2 Mode: Sets LVD2 to disconnect on a voltage or time setpoint.
LVD2 Voltage: LVD2 low voltage disconnect setting (when LVD set for voltage)
LVD2 Reconnect Voltage: LVD2 reconnect setting (when LVD set for voltage).
LVD2 Reconnect Delay: Delay time until LVD2 reconnects once voltage recovers (when LVD set
for voltage).
LVD2 Time: The time before LVD2 disconnection once an AC fail condition occurs (when LVD set
for time).
LVD2 Dependency: Select if LVD2 can disconnect only if LVD1or LVD3 has disconnected, or none.
High Temp Disconnect 1: Enables or disables the High Temperature 1 Disconnect feature. This
feature causes LVD1 contactors to open (disconnect) if a high temperature event occurs.
High Temp Disconnect 2: Enables or disables the High Temperature 2 Disconnect feature. This
feature causes LVD2 contactors to open (disconnect) if a high temperature event occurs.
LVD Contactor Type: Select the type of LVD Contactor. This setting should not be changed.
OBBattFuse Equipment
Battery Fuse Unit
Number of Battery Fuses: Designates the number of battery fuses in the system.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 158

SMDU Equipment
SMDU 1
Shunt # Voltage: Enter the shunt’s voltage rating.
Shunt # Current: Enter the shunt’s current rating.
Current # Break Value: Set the value of the circuit breaker size.
Current # High Limit: Set the High Current Limit alarm point.
Current # Very High Limit: Set the Very High Current Limit alarm point.
SMDUP Equipment
SMDUP 1
Current # Breaker Value: Set the value of the circuit breaker size.
Current # High Current Limit: Set the current high limit alarm point.
Current # Very High Current Limit: Set the current very high limit alarm point.
Shunt # Voltage: Enter the shunt voltage rating.
Shunt # Current: Enter the shunt current rating.
SMDUH Equipment
SMDUH1
Day x Energy Clear: Clear energy for selected day(s).
Hall Calibrate Channel: Select channel number for Hall calibration.
Hall Calibrate Point 1: Enter current value of Hall calibration point 1.
Hall Calibrate Point 2: Enter current value of Hall calibration point 2.
Channel x Energy Clear: Clear energy of selected channel(s).
SMDU-LVD Equipment
SMDU 1 LVD
LVD 1: Enables or disables LVD 1.
LVD 1 Mode: Sets LVD 1 to disconnect on a voltage or time setpoint.
LVD 1 Voltage: LVD 1 low voltage disconnect setting (when LVD set for voltage)
LVD 1 Reconnect Voltage: LVD 1 reconnect setting (when LVD set for voltage).
LVD 1 Reconnect Delay: Delay time until LVD 1 reconnects once voltage recovers (when LVD set
for voltage).
LVD 1 Time: The time before LVD 1 disconnection once an AC fail condition occurs (when LVD
set for time).
LVD 1 Dependency: Select if LVD 1 can disconnect only if LVD2 has disconnected, or none.
LVD 2: Enables or disables LVD 2.
LVD 2 Mode: Sets LVD 2 to disconnect on a voltage or time setpoint.
LVD 2 Voltage: LVD 2 low voltage disconnect setting (when LVD set for voltage)

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 159

 LVD 2 Reconnect Voltage: LVD 2 reconnect setting (when LVD set for voltage).
LVD 2 Reconnect Delay: Delay time until LVD 2 reconnects once voltage recovers (when LVD set
for voltage).
LVD 2 Time: The time before LVD 2 disconnection once an AC fail condition occurs (when LVD
set for time).
LVD 2 Dependency: Select if LVD 2 can disconnect only if LVD 1 has disconnected, or none.
High Temp Disconnect 1: Enables or disables the High Temperature 1 Disconnect feature. This
feature causes LVD1 contactors to open (disconnect) if a high temperature event occurs.
High Temp Disconnect 2: Enables or disables the High Temperature 2 Disconnect feature. This
feature causes LVD2 contactors to open (disconnect) if a high temperature event occurs.
NOTE! Settings that appear “grayed out” can only be made when the controller is in the
“manual control” state. If the controller is set for “Automatic” control, change the
“Auto/Manual State” setting first to the “Manual” setting.
LVD3 Equipment
LVD3 Unit
LVD3: Enables or disables LVD3.
LVD3 Mode: Sets LVD3 to disconnect on a voltage or time setpoint.
LVD3 Voltage: LVD3 low voltage disconnect setting (when LVD set for voltage)
LVD3 Reconnect Voltage: LVD3 reconnect setting (when LVD set for voltage).
LVD3 Reconnect Delay: Delay time until LVD3 reconnects once voltage recovers (when LVD set
for voltage).
LVD3 Time: The time before LVD3 disconnection once an AC failure condition occurs (when LVD
set for time).
LVD3 Dependency: Select if LVD3 can disconnect only if LVD1 or LVD2 has disconnected, or none.
High Temp Disconnect 3: Enables or disables the high temperature 3 disconnect feature. This
feature causes LVD3 contactors to open (disconnect) if a high temperature event occurs.
Battery Charge Tab Programmable Parameter Descriptions
Auto/Manual State:
Auto: The controller automatically controls the power system.
Manual: A User can manually change power system control settings. When you return to
Auto Mode, any settings changed in Manual Mode are returned to their previous setting
(setting before being placed in Manual Mode).
Battery Type Number: Sets the battery parameters per the battery type selected.
Number of Battery Shunts: Sets the number of battery shunts in the system.
Action on Very High Battery Temp:
Disabled: Disables the Battery Thermal Runaway Management feature.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 160

 Lowering Voltage: Sets the Battery Thermal Runaway Management feature to reducing the
output voltage when battery temperature exceeds the Very High BTRM Temperature
setting.
Low Capacity Point: Battery low capacity alarm set point.
Battery Current Limit: Maximum battery charging current setting. For example, a value of
0.150C10 means that the charging current is limited to 15% of the battery’s nominal
capacity.
Over Current Limit: Battery over current alarm setting. For example, a value of 0.300C10 means
that when the charging current reaches 30% of the battery’s nominal capacity, an alarm will
be extended.
Automatic Equalize: Enables or disables the Automatic Equalize Charge feature. When enabled,
the following parameters can be set.
Equalize Start Current: The system is transferred to Equalize Charge mode when battery charge
current increases to this setting. For example, a value of 0.060C10 means that an Automatic
Equalize is started if the battery charge current is greater than 6% of the battery’s nominal
capacity.
Equalize Start Capacity: The system is transferred to Equalize Charge mode when remaining
battery capacity decreases to this setting.
Equalize Stop Current: When in Equalize Charge mode and the battery charge current decreases
below this setting for the "Equalize Charge Stop Delay Time" time period, the system is
transferred to Float Charge mode. For example, a value of 0.010C10 means that when the
charging current is less than 1% of the battery's nominal capacity, the system returns to the
Float mode.
Equalize Stop Delay Time: See "Equalize Charge Stop Current" above.
Maximum Equalize Charge Time: This is the maximum duration, in minutes, that an Automatic
Equalize Charge will last regardless of the other settings.
Cyclic Equalize: Enables or disables cyclic (scheduled) Equalize charging. When enabled, the
following parameters can be set.
Cyclic Equalize Interval: Cyclic (scheduled) Equalize charging interval.
Cyclic Equalize Duration: Cyclic (scheduled) Equalize charging duration.
Equalizing Start Time: Sets the start time for equalizing.
Temperature Compensation Center: Sets the temperature at which the system operates at
normal voltage levels.
Temp Comp Coefficient (slope): Sets the temperature compensation slope or rate of change per
ºC above or below the "Temp Compensation Center" setting. This value is expressed in
millivolt per ºC per string (mV/ºC/str). For example, for a rate of change of 72 mV/ºC/str in a
24-cell 48V nominal battery string, the rate of change is 3 mV per cell.
Temp Comp Voltage Clamp: Enables or disables the temperature compensation voltage clamp
feature. When enabled, the following parameters can be set.
Temp Comp Max Voltage: Upper voltage limit where battery temperature compensation
clamps the voltage.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 161

 Temp Comp Min Voltage: Lower voltage limit where battery temperature compensation
clamps the voltage.
Comp Temp High2: the compensation temperature is too high.
Comp Temp High1: the compensation temperature is high.
Comp Temp Low: the compensation temperature is low.
Calculate Battery Current: Selects if the NCU calculates the battery current in the case of no
battery shunt (load shunt required).
Float Charge Voltage (Solar): Float Charge output voltage setting.
Equalize Charge Voltage (Solar): Equalize Charge output voltage setting.
Float Charge Voltage (RECT): Float Charge output voltage setting.
Equalize Charge Voltage (RECT): Equalize Charge output voltage setting.
Overvoltage 1: Sets the Overvoltage 1 alarm point.
Overvoltage 2: Sets the Overvoltage 2 alarm point.
Under voltage 1: Sets the under voltage 1 alarm point.
Under voltage 2: Sets the under voltage 2 alarm point.
Curr Limited Mode: Selects the current limit mode (disabled, current, or voltage).
Batt 1 Rated Capacity: Enter the battery string's rated capacity.
Batt 2 Rated Capacity: Enter the battery string's rated capacity.
Batt 1 Shunt Current: Enter the battery string shunt’s current rating.
Batt 1 Shunt Voltage: Enter the battery string shunt’s voltage rating.
Batt 2 Shunt Current: Enter the battery string shunt’s current rating.
Batt 2 Shunt Voltage: Enter the battery string shunt’s voltage rating.
Rectifier Expansion
Inactive: Select this option if this is the only NCU controller in the power system.
Primary: Select this option if the power system consists of multiple bays with multiple NCU
controllers, and this NCU controller is to be the primary controller. Note that only one (1)
NCU controller can be set as the primary controller.
NOTE! When primary or secondary is selected, the NCU will start auto configuring. This
process will take more than three (3) minutes.
Secondary: Select this option if the power system consists of multiple bays with multiple
NCU controllers, and this NCU controller is to be a secondary controller.
ALERT! DO NOT set the controller to Secondary from the Web Interface. You will not be able
to log into the controller after it automatically reboots into secondary mode. Controllers to
be designated as secondary controllers need to be set locally via the local keypad and
display.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 162

Primary/Secondary Procedure:
Up to four (4) NCU controllers can be connected when a power system requires a greater number
of rectifiers than can be controlled by a single NCU controller. One (1) controller is designated as
the primary controller, the others as secondary controllers. The rectifiers controlled by the
secondary controllers are designated as Rectifier Group 2 through 4 in the menus.
NOTE! Changing the Rectifier Expansion setting may take more than 3 minutes for the NCU
to configure the feature.
1. Connect the NCU controllers in the multiple bays via the RS485 interface.
2. Set one of the NCU controllers as the primary controller.
3. Set all other NCU controllers as secondary controllers.
ALERT! DO NOT set the controller to Secondary from the Web Interface. You will not be able
to log into the controller after it automatically reboots into secondary mode. Controllers to
be designated as secondary controllers need to be set locally via the local keypad and
display.
4. Set the address of the NCU controllers set as secondary controllers to 201, 202, or 203. Note
that each secondary controller must be set to a different address.
Equalize/Float Charge Control: Places the system in Equalize Charge or Float Charge mode.
Clear Abnormal Bat Current Alarm: Clears an abnormal battery current alarm. The only selection
is Yes. Once Yes is selected and confirmed, the alarm clears.
SMDU-EIB Mode:
Normal: Doesn't use load shunt to calculate load current.
Load Switch: Uses load shunt to sample load current.
Outgoing Alarms Blocked
Normal: Alarms are processed normally.
Blocked: Forces the alarm relays in the "off" state and blocks alarms from changing the
relay state.
Reset Battery Capacity: Resets the battery capacity calculation.
CB Threshold Value: If the load current of a branch circuit increases above the product of [“load
branch circuit current rating” times the CB Threshold Value], the branch current column in
the DU screen (Figure 40) turns yellow, which indicates an observation alarm. (Refer to
Setting the Load Branch Circuit Current Rating on page 149.)
CB Overload Value: If the load current of a branch circuit increases above the product of [“load
branch circuit current rating” times the CB Overload Value], the branch current column in the
DU screen (Figure 40) turns red, which indicates a major alarm. (Refer to Setting the Load
Branch Circuit Current Rating on page 149.)
Discharging Alarm Curr threshold: Sets the discharging alarm current threshold value.
Upper Limit: Sets the upper limit value.
Stable Range Upper Limit: Sets the stable range upper limit value.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 163

 Stable Range Lower Limit: Sets the stable range lower limit value.
Speed Set Point: Sets the speed set point value.
Slow Speed Coefficient: Sets the slow speed coefficient value.
Fast Speed Coefficient: Sets the fast speed coefficient value.
Min Amplitude: Sets the minimum amplitude value.
Max Amplitude: Sets the maximum amplitude value.
Cycle Number: Sets the cycle number..
ECO Tab Programmable Parameter Descriptions
• ECO Mode: Enables or disables the Energy Optimization Mode feature for all rectifiers.
When enabled, the following parameters can be set.
ALERT! The Energy Optimization Mode should NOT be used in systems that operate without
batteries.

Best Operating Point: Percent of full load capacity that the rectifiers operate under in the
Energy Optimization mode.
Load Fluctuation Range: If load fluctuation is less than this value, rectifiers are not turned on
or off for Energy Optimization.
System Energy Saving Point: Energy Optimization is disabled if the load is greater than this
setting.
Cycle Period: This is the time period that rectifiers are turned on and off to maintain an
equal operating time for all rectifiers in the system.
All Rects ON Time: Time all rectifiers are turned on at the end of the “Cycle Period”.
Turn Off Delay: When the Energy Optimization feature determines a rectifier can be
switched off, this is the time delay before the rectifier is turned off.
• Reset Cycle Alarm: Resets the ECO Cycle Alarm. The only selection is Yes. Once Yes is
selected and confirmed, the alarm resets.
LVD Tab Programmable Parameter Descriptions
LVD Unit
• LVD 1: Enables or disables LVD 1. When enabled, the following parameters can be set.
LVD 1 Mode: Sets LVD 1 to disconnect on a voltage or time setpoint.
LVD 1 Voltage: LVD 1 low voltage disconnect setting (when LVD set for voltage)
LVD 1 Reconnect Voltage: LVD 1 reconnect setting (when LVD set for voltage).
LVD 1 Reconnect Delay: Delay time period until LVD 1 reconnects once voltage recovers
(when LVD set for voltage).
LVD 1 Time: The time period before LVD 1 disconnection once an AC fail condition occurs
( when LVD set for time).
LVD 1 Dependency: Select if LVD 1 can disconnect only if LVD2 has disconnected, or none.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 164

 • LVD 2: Enables or disables LVD 2. When enabled, the following parameters can be set.
LVD 2 Mode: Sets LVD 2 to disconnect on a voltage or time setpoint.
LVD 2 Voltage: LVD 2 low voltage disconnect setting (when LVD set for voltage)
LVD 2 Reconnect Voltage: LVD 2 reconnect setting (when LVD set for voltage).
LVD 2 Reconnect Delay: Delay time period until LVD 2 reconnects once voltage recovers
(when LVD set for voltage).
LVD 2 Time: The time period before LVD 2 disconnection once an AC fail condition occurs
( when LVD set for time).
LVD 2 Dependency: Select if LVD 2 can disconnect only if LVD 1 has disconnected, or none.
High Temp Disconnect1: Enables or disables the High Temperature 1 Disconnect feature.
This feature causes LVD 1 contactors to open (disconnect) if a high temperature event occurs.
(See "HTD Point" and “HTD Reconnect Point” under the “System Tab Programmable
Parameter Descriptions” starting on page 152.)
High Temp Disconnect2: Enables or disables the High Temperature 2 Disconnect feature.
This feature causes LVD 2 contactors to open (disconnect) if a high temperature event occurs.
(See "HTD Point" and “HTD Reconnect Point” under the “System Tab Programmable
Parameter Descriptions” starting on page 152.)
• LVD Contactor Type: Select the type of LVD Contactor. This setting should not be changed.
SMDU 1 LVD
• LVD 1: Enables or disables LVD 1. When enabled, the following parameters can be set.
LVD 1 Mode: Sets LVD 1 to disconnect on a voltage or time setpoint.
LVD 1 Voltage: LVD 1 low voltage disconnect setting (when LVD set for voltage)
LVD 1 Reconnect Voltage: LVD 1 reconnect setting (when LVD set for voltage).
LVD 1 Reconnect Delay: Delay time period until LVD 1 reconnects once voltage recovers
(when LVD set for voltage).
LVD 1 Time: The time period before LVD 1 disconnection once an AC fail condition occurs
( when LVD set for time).
LVD 1 Dependency: Select if LVD 1 can disconnect only if LVD2 has disconnected, or none.
• LVD 2: Enables or disables LVD 2. When enabled, the following parameters can be set.
LVD 2 Mode: Sets LVD 2 to disconnect on a voltage or time setpoint.
LVD 2 Voltage: LVD 2 low voltage disconnect setting (when LVD set for voltage)
LVD 2 Reconnect Voltage: LVD 2 reconnect setting (when LVD set for voltage).
LVD 2 Reconnect Delay: Delay time period until LVD 2 reconnects once voltage recovers
(when LVD set for voltage).
LVD 2 Time: The time period before LVD 2 disconnection once an AC fail condition occurs
( when LVD set for time).
LVD 2 Dependency: Select if LVD 2 can disconnect only if LVD 1 has disconnected, or none.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 165

 High Temp Disconnect1: Enables or disables the High Temperature 1 Disconnect feature.
This feature causes LVD 1 contactors to open (disconnect) if a high temperature event occurs.
(See "HTD Point" and “HTD Reconnect Point” under the “System Tab Programmable
Parameter Descriptions” starting on page 152.)
High Temp Disconnect2: Enables or disables the High Temperature 2 Disconnect feature.
This feature causes LVD 2 contactors to open (disconnect) if a high temperature event occurs.
(See "HTD Point" and “HTD Reconnect Point” under the “System Tab Programmable
Parameter Descriptions” starting on page 152.)
Temperature Tab Programmable Parameter Descriptions
Ambient Temperature Sensor: Sets the temperature sensor which displays the ambient
temperature on the Web Interface’s Homepage. Note that this temperature sensor MUST
be set as an ambient temperature sensor. Select "None", or the temperature probe (System
T1, System T2, System T3, IB2 T1, IB2 T2, EIB T1, EIB T2, SMTemp1 T1 …, SMTemp1 T8,
SMTemp8 T1 …, SMTemp8 T8). You can also select Maximum or Average which takes the
maximum or average reading of the temperature probes (any of System T1, System T2,
System T3, IB2 T1, IB2 T2, EIB T1, EIB T2, SMTemp1 T1 …, SMTemp1 T8, SMTemp8 T1 …,
SMTemp8 T8) set as ambient temperature probes. When set to any value except “none”, the
following parameters can be set.
Ambient Temperature High 1: Allows you to set an ambient temperature high 1 alarm
point.
Ambient Temperature Low: Allows you to set an ambient temperature low alarm point.
Ambient Temperature High 2: Allows you to set an ambient temperature high 2 alarm
point.
System Temp 1: Sets this temperature sensor to None, Battery, or Ambient.
System Temp 2: Sets this temperature sensor to None, Battery, or Ambient.
System Temp 3: Sets this temperature sensor to None, Battery, or Ambient.
IB2 Temp 1: Sets temperature port 1 on the IB2 board to None, Battery, or Ambient.
IB2 Temp 2: Sets temperature port 2 on the IB2 board to None, Battery, or Ambient.
EIB Temp 1: Sets temperature port 1 on the EIB board to None, Battery, or Ambient.
EIB Temp 2: Sets temperature port 2 on the EIB board to None, Battery, or Ambient.
Temp Compensation Probe Number: Select "None" for no temperature compensation, or the
temperature probe (System T1, System T2, System T3, IB2 T1, IB2 T2, EIB T1, EIB T2,
SMTemp1 T1 …, SMTemp1 T8, SMTemp8 T1 …, SMTemp8 T8) sensing battery temperature
for temperature compensation. You can also select Maximum or Average which takes the
maximum or average reading of the temperature probes (any of System T1, System T2,
System T3, IB2 T1, IB2 T2, EIB T1, EIB T2, SMTemp1 T1, …, SMTemp1 T8, SMTemp8 T1, …,
SMTemp8 T8) set as battery temperature probes. When used with an SM-BRC, you can
select to average the SM-BRC temperature probe readings (Average SMBRC setting).
Comp Temp High 2: Allows you to set a compensation temperature high 2 alarm point.
Comp Temp High 1: Allows you to set a compensation temperature high 1 alarm point.
Comp Temp Low: Allows you to set a compensation temperature low alarm point.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 166

 BTRM Temp Sensor: Sets the BTRM (Battery Thermal Runaway Management) temperature
sensor. Note that this temperature sensor MUST be set as a battery temperature sensor.
Select "None", or the temperature probe (System T1, System T2, System T3, IB2 T1, IB2 T2,
EIB T1, EIB T2, SMTemp1 T1 …, SMTemp1 T8, SMTemp8 T1 …, SMTemp8 T8). You can also
select Maximum or Average which takes the maximum or average reading of the
temperature probes (any of System T1, System T2, System T3, IB2 T1, IB2 T2, EIB T1, EIB T2,
SMTemp1 T1, …, SMTemp1 T8, SMTemp8 T1, …, SMTemp8 T8) set as battery temperature
probes. When used with an SM-BRC, you can select to average the SM-BRC temperature
probe readings. When set to any value except “none”, the following parameters can be set.
NOTE! The BTRM sensor is the sensor which is used for the High Temperature Disconnect (HTD)
Feature.
BTRM Temp High 2: Allows you to set a BTRM temperature high 2 alarm point. If battery
temperature exceeds this setting, system voltage is lowered to the “Very High Temp
Voltage” setting (if “Very High Battery Temp Action” is enabled).
BTRM Temp High 1: Allows you to set a high BTRM temperature high 1 alarm point.
Rectifiers Tab Programmable Parameter Descriptions
Rectifier Current Limit: Temporarily sets the Rectifier Current Limit. (percent of nominal).
Settings returns to original when controller is returned to the Auto mode.
Rectifier Trim: Temporarily sets the output voltage for all rectifiers. Voltage can be increased or
decreased from the existing Float Charge or Equalize Charge setting, depending which mode
the Controller was in when set to " Manual". Settings reverts to original when Controller is
returned to the Auto mode.
DC On/Off Control: Temporarily turns the DC output on or off for all rectifiers. Setting returns to
original when Controller is returned to the Auto mode.
AC On/Off Control: Temporarily turns the AC input on or off for all rectifiers. Setting returns to
original when Controller is returned to the Auto mode.
Rectifiers LED Control: Temporarily sets if a rectifier’s local power indicator blinks when the
Controller is communicating with the rectifier. Setting returns to original when Controller is
returned to the Auto mode.
Fan Speed Control: Temporarily sets the fan speed for all rectifiers. Setting returns to original
when Controller is returned to the Auto mode.
Clear Rectifier Lost Alarm: Clears a rectifier lost alarm.
Reset Cycle Alarm: Reset a rectifier in ECO Mode cycle alarm.
Confirm Rect ID/Phase: Confirms the position and input phase for all rectifiers.
Clear Rectifier Comm Fail Alarm: Clears a rectifier communication fail alarm.
Reset Rectifier IDs: The only selection for "Reset Rectifier IDs" is Yes. Once Yes is selected and
confirmed, the individual rectifier Web pages appear to allow individual rectifier settings
(including Rectifier Position/ID and Phase) to be changed.
HVSD Limit: Sets the High Voltage Shutdown point for all rectifiers.
HVSD Restart Time: When the High Voltage Shutdown Restart feature is enabled and the output
exceeds the high voltage limit, the rectifiers restart after this time expires.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 167

 Restart on HVSD: Enables or disables the High Voltage Shutdown Restart feature for all rectifiers.
Sequence Start Interval: Sets the sequence start interval (time between starting each rectifier in
the system).
Walk-In: Enables or disables the start-up walk-in feature for all rectifiers.
Turn On when AC Over Voltage: Enables or disables the "Turn On when AC Overvoltage" feature.
When the system is operating on “week” grid input power (i.e. diesel generator), the input
voltage may have a very high peak voltage which may cause a rectifier not to turn on. If
“Rectifier On at AC Overvoltage" feature is enabled, the rectifier is forced to turn on.
ECO Mode: Enables or disables ECO Mode.
Best Operating Point: Percent of full load capacity that the rectifiers operate under in the
Energy Optimization mode.
Load Fluctuation Range: If load fluctuation is less than this value, rectifiers are not turned
on or off for Energy Optimization.
System Energy Saving Point: Energy Optimization is disabled if the load is greater than this
setting.
Cycle Period: This is the time that rectifiers are turned on and off to maintain an equal
operating time for all rectifiers in the system.
All Rects ON Time: Time all rectifiers are turned on at End of Cycle.
Turn Off Delay: When the Energy Optimization feature determines a rectifier can be
switched off, this is the time delay before the rectifier is switched off.
Input Current Limit: Sets the Input Current Limit point for all rectifiers.
MixHE Power: Allows the system to use rectifiers of different output capacity. When set to
derated power, the output capacity of the higher capacity rectifiers are set to the capacity of
the lowest.
HVSD: Enables or disables the High Voltage Shutdown feature for all rectifiers.
Diesel Generator Power Limit: Enables or disables the Diesel Power Limit feature. This feature
limits rectifier output power to a percentage of maximum when AC input is supplied by a
diesel-alternator set.
Diesel Generator Digital Input: Sets DIs for diesel input.
Diesel Gen Power Limit Point Set: Sets, as a percentage, the maximum output power at which
rectifiers can operate when: (1) the Diesel Power Limit feature is enabled and (2) a digital
input signal is received from the connected diesel-alternator set.
Normal Update: Sets rectifier software normal update. When the rectifier is normally
communicating with the controller, the rectifier software is automatically updated as
needed.
Force Update: Sets rectifier software forced update. When the rectifier is inserted into a
mounting slot, the rectifier software is automatically updated if needed.
Default Voltage：Sets the default voltage value.
HVSD LVD1 Disconn Enable: Enables or disables HVSD LVD1 Disconnections.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 168

 Clear ACDC kwh: Whether to clear ACDC kwh. The only option is ‘Yes’.
3-phase Balance Enabled: Enables or disables 3-phase balance.
AC Input Enabled: Enables or disables AC input.
DC/DC Converters Tab Programmable Parameter Descriptions
• Clear Converters Comm Fail: Clears an “Converter Comm Fail” alarm. The only selection is
Yes. Once Yes is selected and confirmed, the alarm clears.
• Clear Converter Lost Alarm: Clears a converter lost alarm. The only selection is Yes. Once
Yes is selected and confirmed, the alarm clears.
• Converter Trim: Temporarily sets the output voltage for all converters when the controller is
in Manual mode. Setting returns to original when controller is returned to the Auto mode.
• DC On/Off Control: Temporarily turns the DC output on or off for all converters.
• Converters LED Control: Temporarily sets whether or not a converter’s local power indicator
blinks when the controller is communicating with the converter when the controller is in
Manual mode. Setting returns to original when controller is returned to the Auto mode.
• Fan Speed Control: Sets the fan speed for all converters.
• Confirm Converter ID: After changing converter ID assignments, use this menu item to
confirm the change. The only selection is Yes. Once Yes is selected and confirmed, the ID
setting of all converters is updated.
• Clear All Converters Comm Fail: Clears an “All Converter Comm Fail” alarm. The only
selection is Yes. Once Yes is selected and confirmed, the alarm clears.
• Converter Current Limit: Enables or disables adjusting the output current limit point. When
enabled, the following parameters can be set.
• Reset Converter IDs: Resets the converter IDs after they have been previously changed and
confirmed. The only selection is Yes. Once Yes is selected and confirmed, the NCU resets the
converter IDs by reassigning ID numbers.
Solar Tab Programmable Parameter Descriptions
• Solar Converter Current Limit: Sets the output current limit point for all solar converters
combined.
NOTE! Can only be made when the controller is in the "manual control" state. If the
controller is set for "automatic" control, change the “Auto/Manual State” setting first to the
“Manual” setting.
• Solar Converter Trim: Temporarily sets the output voltage for all solar converters when the
controller is in Manual mode. Voltage can be increased or decreased from the existing Float
Charge or Equalize Charge setting, depending which mode the controller was in when set to
"Manual". Setting reverts to original when controller is returned to the Auto mode.
• DC On/Off Control: Temporarily turns the DC output on or off for all solar converters when
the controller is in Manual mode. Setting returns to original when controller is returned to
the Auto mode.
• Solar Converter LED Control: Temporarily sets whether or not a solar converter’s local power
indicator blinks when the controller is communicating with the solar converter when the

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 169

 controller is in Manual mode. Setting returns to original when controller is returned to the
Auto mode.
• Fan Speed Control: Sets the fan speed for all solar converters.
• Clear Solar Converter Lost Alarm: Clears a solar converter lost alarm. The only selection is
Yes. Once Yes is selected and confirmed, the alarm clears.
• Confirm Solar Converter ID: After changing solar converter ID assignments, use this menu
item to confirm the change. The only selection is Yes. Once Yes is selected and confirmed,
the ID setting of all solar converters is updated.
• Reset Solar Converter IDs: Resets the solar converter IDs after they have been previously
changed and confirmed. The only selection is Yes. Once Yes is selected and confirmed, the
NCU resets the solar converter IDs by reassigning ID numbers.
• High Voltage ShutDown Limit: Sets the High Voltage Shutdown point for all solar converters.
• Restart on HVSD: Enables or disables the High Voltage Shutdown Restart feature for all solar
converters. When enabled, the following parameters can be set.
HVSD Restart Time: When the High Voltage Shutdown Restart feature is enabled and the
output exceeds the high voltage limit, the solar converters restart after this time period
expires.
• Walk-In: Enables or disables the start-up walk-in feature for all solar converters. When
enabled, the following parameters can be set.
Walk- In Time: Sets the start-up walk-in time when the “Walk-In” setting above is set to
enabled.
• Sequence Start Interval: Sets the sequence start interval (time period between starting each
solar converter in the system).
• Clear Solar Converter Comm Fail: Clears a solar converter communication fail alarm. The
only selection is Yes. Once Yes is selected and confirmed, the alarm clears.
Battery Test Tab Programmable Parameter Descriptions
• AC Fail Test: Enables or disables starting a battery discharge test during an AC input failure
condition.
• Constant Current Test: Enables or disables a Constant Current Battery Discharge Test.
During this test, the controller automatically adjusts the rectifiers' output voltage to maintain
the battery discharge current at a preset value (Constant Current Test Current). When
enabled, the following parameters can be set.
Constant Current Test Current: Constant current setting for a Constant Current Battery
Discharge Test.
• Short Test: Enables or disables a Short Battery Discharge Test. A Short Battery Discharge
Test is a short duration battery discharge test used to verify that parallel batteries are
discharging equally. If the discharge current difference between the two batteries exceeds a
preset value, an alarm is generated. When enabled, the following parameters can be set.
NOTE! This test requires a system with two battery shunts.

Short Test Cycle: Short Battery Discharge Test interval (days).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 170

 Short Test Time: Short Battery Discharge Test time (minutes).
Short Test Max Difference Current: An alarm is generated if the maximum difference
between discharge currents of the two batteries exceeds this limit.
• Test Voltage Level: System output voltage setting during a battery discharge test.
• End Test Voltage: This is the "end of test voltage level" for battery discharge tests. A battery
discharge test will end if battery voltage decreases to this setting.
• End Test Time: This is the "end of test time period” for battery discharge tests. A battery
discharge test will end if this time period is exceeded.
• End Test Capacity: This is the "end of test remaining battery capacity" for battery discharge
tests. A battery discharge test will end if remaining battery capacity decreases to this
setting. For example, a value of 0.700C10 means that when the discharging current reaches
70% of the battery's nominal capacity, the battery test is ended.
• Record Threshold: Every time the battery voltage is changed more than this threshold, a
new line is stored in the battery test log.
• Number of Planned Tests per Year: Number of planned battery discharge test per year.
There can be up to twelve (12) battery discharge tests per year. A "0" setting disables the
planned test feature. When enabled, the following parameters can be set.
Planned Test # (MM-DD Hr): Setting for when planned battery discharge test # occurs. Note
that there can be up to twelve (12) battery discharge tests per year.
• Clear Bad Battery Alarm: Clears a bad battery alarm. The only selection is Yes. Once Yes is
selected and confirmed, the alarm clears.
• Clear Battery Test Fail Alarm: Clears a battery test fail alarm. The only selection is Yes. Once
Yes is selected and confirmed, the alarm clears.
• Clear Discharge Curr Imbalance: Clears a discharge current imbalance alarm. The only
selection is Yes. Once Yes is selected and confirmed, the alarm clears.
Time Settings Tab Programmable Parameter Descriptions
See also “Changing the Date and Time” on page 38.
• Specify Time
- Get Local Time from Connected PC: Allows you to automatically set the time. When
selected, the controller will get the same time as the connected PC.
- Date & Time: Allows you to manually set the date and time.
• Local Zone (for synchronization with time servers): When selected, the controller will get the
local zone automatically or you can enter the zone.
• Get time automatically from the following servers.
- When selected, the controller will get the time from the selected time server. The
controller will also adjust the time per the "Local Zone" setting.
History Log Menu
The History Log Menu allows you to view and save the various logs available in the NCU.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 171

Alarm History Log Tab
Select Device and Time
Select the "Device" to query from the drop-down list box. Select the "from" and "to" time.

Figure 64: Alarm History Log Device and Time Selection

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 172

Query Alarm History Log
Click “Query” to query for alarms within selected time slot. The Web page displays the last 500
entries.

Figure 65: Alarm History Log Query

Upload Alarm History Log

Click “Upload” to open the log into another window. You can then save the log as an .html (Web
page) or .txt (text) file.

Figure 66: Alarm History Log Upload

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 173

Battery Test Log Tab
Select Battery Test Number
Select the Battery Test Log to query from the drop-down list box. Battery test #1 is the most
recent.

Figure 67: Battery Test Log Number Selection

Query Selected Battery Test

Click “Query” to query the selected battery test. The Web page displays up to ten (10) battery
tests.
NOTE! Battery tests in which battery voltage changed less than the Record Threshold setting
are not recorded.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 174

Figure 68: Battery Test Log Query

Upload Battery Test Log

Click “Upload” to open the log into another window. You can then save the log as an .html (Web
page) or .txt (text) file.

Figure 69: Battery Test Log Upload

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 175

Event Log Tab
Select Time
Select the "from" and "to" time.

Figure 70: Event Log Time Selection

Query Event Log

Click “Query” to query the Event Log. The Web page displays the last 500 entries.

Figure 71: Event Log Query

Upload Event Log

Click “Upload” to open the log into another window. You can then save the log as an .html (Web
page) or .txt (text) file.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 176

Figure 72: Event Log Upload

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 177

Data History Log Tab
Select Device and Time
Select the "Device" to query from the drop-down list box. Select the "from" and "to" time.

Figure 73: Data History Log Device and Time

Query Data History Log

Click “Query” to query for Date History within selected time slot. The Web page displays the last
500 entries.

Figure 74: Data History Log Query

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 178

Upload Data History Log
Click “Upload” to open the log into another window. You can then save the log as an .html (Web
page) or .txt (text) file.

Figure 75: Data History Log Upload

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 179

System Log Tab
Select Time
Select the "from" and "to" time.

Figure 76: System Log Time Selection

Query System Log

Click “Query” to query the System Log. The Web page displays the last 500 entries.

Figure 77: System Log Query

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 180

Upload System Log
Click “Upload” to open the log into another window. You can then save the log as an .html (Web
page) or .txt (text) file.

Figure 78: System Log Upload

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 181

System Inventory Menu
The System Inventory Menu allows you to view product information of the intelligent devices (i.e.
rectifiers, converters, SMDUs, IB, etc.) connected to the controller.

Figure 79: System Inventory Menu

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 182

Advanced Settings Menu
The Advanced Settings Menu allows you to change (if you have the proper privilege level
programmed in your User settings) the settings of the various advanced programmable parameters.
Settings are grouped per function. Select a tab in the Advanced Settings Menu to change that
functions programmable parameters.

Ethernet Tab
You can configure the controller's network parameters.
• IPv4: IP Address, Subnet Mask, and Default Gateway.
• IPv6: IPv6 Address, IPv6 Prefix, and IPv6 Gateway.
After modifying the network parameters, click "Save" to validate the change made to the
parameters.
NOTE! After changing the IP Address, you will need to login again with the new IP address.

Figure 80: Ethernet Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 183

Users Tab
You can add, edit, and delete Users. These are the Users that can log onto the controller both
locally (local display access) or remotely using the Web Interface.
• A maximum of sixteen (16) Users can be set up in the NCU.
• A maximum of five (5) Users can access the NCU at the same time.

Figure 81: Users Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 184

Adding a User
1. Enter the User’s Name in the “User Name” field.
User Name: Eight (8) characters maximum; the valid characters are 0-9, a-z, A-Z, and _.
2. Select the privilege of the User from those listed in the "Privilege" drop-down list box.
See "Web Interface User Privilege Levels" on page 186 for a description. See also
“Passwords and Privilege Levels” on page 25.
3. Enter an E-Mail address for this User. This email address is used for cases where you
forget your password. The NCU will email you your password. See “Logging into the
Controller” on page 34.
4. Enter a password for this User in the "Password" field.
Password: Thirteen (13) characters maximum; the valid characters are 0-9, a-z, A-Z, and _.
Passwords must be at least six (6) characters long.
5. Re-enter the password for this User in the "Confirm" field.
6. Click the "Add" button to add the User.
NOTE! To reset the form (i.e. to start over) and erase all information entered, click on the
“Reset” button.

Modifying an Existing User

1. Select the User to be modified from those listed in the "User Information” list.
2. Modify the parameters of this User in the "User Name", "Privilege ", “E-Mail”, and/or
"Password" field.
3. Click the "Modify" button to modify the parameters of this User.
NOTE! To reset the form (i.e. to start over) and erase all information entered, click on the
“Reset” button.

Deleting a User
4. Select the User to be deleted from those listed in the "User Information" list.
5. Click the "Delete" button to delete this User.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 185

Web Interface User Privilege Levels
Users are programmed with a “privilege level” (see Table 5).

Table 5: User Privilege Levels

Access Level Default User Name

Authority
(Privilege Level) and Password

The User can only read (browse) information in

Level A (Browser) none set the menus.
The User has access to the system "Manual
Level B (Operator) none set Mode Control Settings" menus.
The User has access to the system "Settings"
menus and can download the "SettingParam.tar"
Level C (Engineer) none set file. The User does not have access to update
the OS application and modify, add, or delete
Users.
The User has full access to all menus; including
Level D (Administrator) admin, 640275 update the OS application and modify, add, and
delete Users.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 186

SNMP Tab
Configures SNMP V2 and V3 parameters.

Accepted Trap Level Parameter Description

• Accepted Trap Level: Sets SNMP V2 and V3 trap level.

Adding an Entry
1. Enter the parameters in the parameter fields.
2. Click the "Add" button to add the entry.
NOTE! To reset the form (i.e. to start over) and erase all information entered, click on the
“Reset” button.

Modifying an Existing Entry

3. Select the Entry to be modified from those listed at the top of the screen.
4. Modify the parameters.
5. Click the "Modify" button to modify the parameters for this Entry.
NOTE! To reset the form (i.e. to start over) and erase all information entered, click on the
“Reset” button.

Deleting an Entry
6. Select the Entry to be deleted from those listed at the top of the screen.
7. Click the "Delete" button to delete this Entry.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 187

NMSV2 Configuration Description (Network Management System)
Configures SNMP Version 1 and 2 parameters.
You can configure the following parameters.
• NMS IP: The permitted IP to access the NMSV2 agent. Check the IPV6 box when entering an
IPV6 address.
• Public Community: The public community string.
• Private Community: The private community string.
• Trap Enabled: Trap function enabled or disabled.
NOTE! Only listed IP Addresses will have SNMP access.

NOTE! To reset the form (i.e. to start over) and erase all information entered, click on the
“Reset” button.

Figure 82: SNMP - NMSV2 Configuration (cont’d on next page)

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 188

Figure 82: SNMP - NMSV2 Configuration (cont’d from previous page)

IPV6 checkbox appears once you start

typing an NMS IP. Check the IPV6 box
when entering an IPV6 address.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 189

NMSV3 Configuration Description (Network Management System)
Configures SNMP Version 3 parameters.
You can configure the following parameters.
• Use Name: The permitted User to access the NMSV3 agent.
• Priv Password DES: The privacy DES password used to encrypt the data.
• Auth Password MD5: The authorization MD5 password used to encrypt the digital signature.
• Trap Enabled: Trap function enabled or disabled.
• Trap IP: The IP to which the trap is sent. Check the IPV6 box when entering an IPV6 trap
address.
• Trap Security Level: The SNMP v3 data security level (NoAuthNoPriv, AuthNoPriv, or
AuthPriv).
- NoAuthNoPriv: SNMP messages are sent without authentication and without privacy.
- AuthNoPriv: SNMP messages are sent with authentication but without privacy.
- AuthPriv: SNMP messages are sent with authentication and with privacy.
NOTE! For SNMP v3, the security level for Get and Set operations is set to “AuthPriv” and
cannot be adjusted.
NOTE! Controller must be reset after configuration of initial SNMP v3 User (Advanced
Settings Menu / SW Maintenance Tab / Restore Factory Defaults / Reboot Controller).

Figure 83: SNMP - NMSV3 Configuration

Check the
IPV6 box
when
entering an
IPV6 trap

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 190

Language Tab
The local display and Web Interface always has an English language option. Multiple local
languages are also supported. One local language option is displayed at a time with the English
language option. To select another local language option to display, use the Web Interface
Language Tab (see Figure 84).
You can select from the following local languages: Spanish and French. Once you select a new local
language, the controller is automatically rebooted to make the selected local language valid.
See Figure 85 to change the language the local display and Web Interface uses.

Figure 84: Language Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 191

Figure 85: Selecting the Local Language for the Local Display and Web Interface Menus

Web Interface Login Screen

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 192

SW Maintenance Tab
Allows you to perform software maintenance procedures.

Figure 86: SW Maintenance Tab

Auto Config Procedure

The auto configuration feature scans the system for intelligent equipment connected to controller
(such as SMDU, IB and EIB) and configures these into the controller automatically.
To start the auto configuration process, click on the "Auto Config" button.

Figure 87: Auto Config

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 193

Restore Factory Default Configuration Procedure
This procedure is used to restore all changes made to the NCU to factory defaults.
Procedure
ALERT! When this procedure is performed, the controller’s existing configuration and
parameter settings will be lost. The “SettingParam.tar” file is deleted. Before restoring the
factory default configuration, if you have made changes to the NCU, save the
“SettingParam.tar” file (see “Backing Up the NCU Configuration” on page 50).
1. Click on the “Restore Defaults” button.

Figure 88: Restore Factory Defaults

2. Click “OK” to confirm to overwrite the existing "SettingParam.tar" file in memory with
the stored "SettingParam.tar" file.
The controller will automatically reboot. All settings WILL BE restored to the defaults of the
stored "SettingParam.tar" file.
NOTE! After rebooting, you must exit your browser and re-login to see any changes made.

NOTE! SOME SYSTEMS REQUIRE CHANGES TO THE NCU CONFIGURATION DURING FINAL
TEST BEFORE BEING SHIPPED. These systems are supplied with a USB memory device that
contains a “SettingParam.tar” file as shipped. If provided, the “SettingParam.tar” file has a
seven-digit UIN (Unique Identification Number) preceding the “SettingParam.tar” filename.
The UIN identifies a “SettingParam.tar” file for use with a specific system. This file can be
used to restore your system to the configuration as shipped. Refer to “Reloading a Backed-Up
NCU Configuration” on page 51 to reload the supplied “SettingParam.tar” file.
TO RESTORE THESE SYSTEMS TO THE NCU CONFIGURATION AS SHIPPED, RESTORE DEFAULTS AS
DESCRIBED ABOVE; THEN RELOAD THE SUPPLIED "SETTINGPARAM.TAR" FILE.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 194

Retrieve "SettingParam.tar" File Procedure
See also “Backing Up the NCU Configuration” on page 50.
A file named “SettingParam.tar” is automatically created/appended by the controller whenever a
User (or the factory at the time of shipment) makes changes to the NCU via the local display or Web
Interface. This file can be saved to your computer, so you can restore any custom settings you may
have made.
NOTE! It is strongly recommended that you save a copy of the “SettingParam.tar” file
whenever you customize any parameter settings. Then, if you ever replace the controller or
perform a "Restore Defaults" procedure, you can restore your customized settings by
downloading the previously saved “SettingParam.tar” file back into the controller.
Prior to changing settings, ensure the current "SettingParam.tar" files are backed up. After making
changes, create new backup files.
Procedure
3. Click on the “Retrieve File” button to save the file named "SettingParam.tar" to your
computer. Select where you want the file to be copied to on your computer.
NOTE! Ensure Internet Explorer security settings are set to enable a file to be copied to your
computer.

To aid in file management, you may change the name of the “SettingParam.tar” file to
differentiate it from other "SettingParam.tar" files saved. The new name can use alpha and
numeric characters preceding the original “SettingParam.tar” name (the end of the new file
name must always be “SettingParam.tar”; for example, an acceptable filename would be
“seville4SettingParam.tar”).

Figure 89: Retrieve "SettingParam.tar" File

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 195

Upload/Download Procedure
See also “Backing Up the NCU Configuration” on page 50, “Reloading a Backed-Up NCU
Configuration” on page 51.
You can download (from your computer into the controller) a configuration package, application
("All") package, language package (filename of each has a tar or tar.gz extension), or
“SettingParam.tar file”.
You can upload (from the controller to your computer) a configuration package or language
package.
Procedure
1. To upload or download a file, you need to shut down the controller first. When you
select the SW Maintenance Tab, click on the “Stop Controller” button.

Figure 90: Upload/Download - Stop Controller

2. The following window opens.

Figure 91: Upload/Download --Controller Stopped

3. Click "OK".
4. The following window opens.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 196

Figure 92: Upload/Download File

ALERT! Never navigate from this Web page without first clicking on "Start Controller". If you
do, you will not have Web access. A manual system reset is required to restore Web access.
5. To download (from your computer into the controller) a configuration package,
application ("All") package, language package, or a "SettingParam.tar" file; click the
"Browse..." button and navigate to the folder where the file to download is located.
Select the file to be downloaded and then click the "Download to Controller" button.
Click "Start Controller" to restart the controller with the downloaded file installed.
To upload a file to your computer, select "Configuration Package" or "Language Package"
from the "File in Controller" drop-down list box, and click on the "Upload to Computer"
button to save the file to your computer. Select where you want the file to be copied to on
your computer. Click "Start Controller" to restart the Controller.
NOTE! Ensure Internet Explorer security settings are set to enable a file to be copied to your
computer.

NOTE! A Configuration Package is a package of files containing all the default parameter
settings and any User changes to alarm severity levels, relay assignments, signal names and
site information.
NOTE! An Application “All” package file has both the application (software) and
configuration package and is usually supplied for an application upgrade.
NOTE! A Language Package is a package of files containing all the default names of the
parameters in two languages. Typically, these would be in English and Spanish. The
language package cannot be changed by the User. Consult NOKIA if a different language
package is required.
NOTE! A file named “SettingParam.tar” is automatically created/appended by the Controller
whenever a User (or the factory at the time of shipment) makes changes to the NCU via the
local display or Web Interface. This file also contains the Configuration Package described
above.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 197

Alarms Tab
NOTE! This list is dynamic and will only show you the equipment that you have in your
system.

• Allows you to define the alarm level for each alarm. (See also Table 1 on page 10.)
• Allows you to map alarms to the alarm relays.

Figure 93: Alarms Tab

Procedure
1. Select the equipment type to display the alarms associated to it. Also displayed is the
alarm level and alarm relay number assigned to this alarm.
2. To modify the alarm level and/or alarm relay number, click on the “Modify” button
for that alarm signal.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 198

 3. The following window opens. Select the New Alarm Level and/or New Relay Number
and click on “Set”.
“None” means there is no related relay number.

Figure 94: Setting Alarm Level / Relay Number

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 199

DI Alarms Tab
• Allows you to change the digital input alarm signal full name (name displayed in the Web
Interface menus).
• Allows you to change the digital input alarm signal abbreviation name (name displayed in the
local display menus).
• Allows you to define the alarm level for each digital input alarm. (See also Table 1 on page
10.)
• Allows you to map the digital input alarms to the alarm relays.
• Allows you to set the alarm state for the digital inputs (high or low).

Figure 95: DI Alarm Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 200

Procedure
1. To modify the digital input alarm parameters, click on the “Modify” button for that
digital input alarm signal.
2. The following window opens.

Figure 96: Setting DI Alarm

3. Change the following parameters as desired and click on “Set”.

• Signal Full Name: Name displayed in the Web Interface menus.
• Signal Abbr Name: Name displayed in the local display menus.
• New Alarm Level: Alarm level for this digital input alarm. (See also Table 1 on page 10.)
• New Relay Number: Select a relay number to map to this digital input alarm.
“None” means there is no related relay number.
• New Alarm State: Select high or low to set the alarm state for the digital input.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 201

Fuse Tab
• Allows you to change the fuse full name (name displayed in the Web Interface menus).
• Allows you to change the fuse abbreviation name (name displayed in the local display
menus).

Figure 97: Fuse Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 202

Procedure
1. To change the fuse name, click on the “Modify” button for that fuse.
2. The following window opens.

Figure 98: Changing Fuse Names

3. Change the following parameters as desired and click on “Set”.

• Signal Full Name: Name displayed in the Web Interface menus.
• Signal Abbr Name: Name displayed in the local display menus.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 203

Alarm Report Tab
• In the SMTP section, you can set the Alarm Report Feature and part of the Forget Password
Feature (you must also set an E-Mail address in the User tab for the Forget Password feature).
• In the SMS section, you can set cell phone number for receiving alarm reports and the alarm
report level.
NOTE! A GSM modem must be connected to the USB port of the NCU for SMS functionality.

Figure 99: Alarm Report Tab

Alarm Report Feature

Set the following parameters.
• Email To: Valid email recipient to receive alarm reports.
• Server IP: IPV4 Server address. Obtain from your IT department.
• Server Port: Server port. Obtain from your IT department.
• Email From: The NCU or Site email address. Will be displayed in the email from field of the
received email.
• Privilege: Select Enabled (if email authentication is required) or Disabled as required (see
your IT department). When enabled, set the following parameters.
- SMTP Account: SMTP account number. Obtain from your IT department.
- SMTP Password: SMTP password. Obtain from your IT department.
• Alarm Report Level: Select the level of alarm reports you want to receive.
Forget Password Feature
Set the following parameters. Also set an E-Mail address in the User tab. This is the email the
password will be sent to.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 204

 • Email To: Any valid email recipient. This can be the same email address set in the User tab if
not also using the alarm report feature.
• Server IP: IPV4 Server address. Obtain from your IT department.
• Server Port: Server port. Obtain from your IT department.
• Email From: The NCU or Site email address. Will be displayed in the email from field of the
received email.
• Privilege: Select Enabled (if email authentication is required) or Disabled as required (see
your IT department). When enabled, set the following parameters.
- SMTP Account: SMTP account number. Obtain from your IT department.
- SMTP Password: SMTP password. Obtain from your IT department.
• Alarm Report Level: If you only want to use the Forgot Password Feature, set the Alarm
Report Level to None.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 205

Generator Tab
If you have a special configuration with this feature, you can set the various generator related
parameters.

Figure 100: Generator Tab

Changing Programmable Parameters in the Generator Tab

To change a programmable parameter, select or enter a new value for the parameter then click on
“Set” to change the value.

Generator Tab Programmable Parameter Descriptions

• Hybrid Mode: Refer to “Hybrid Control Function (Supporting Generator, Solar and Wind
Energy Input, and Optimization)” on page 16 for more information on the Hybrid Mode.
- Disabled, Only Diesel Mode, or Diesel with AC Mode: Sets the Hybrid Mode or disables
the function.
• DG Relay Selection: Selects Relay Output1, Relay Output2… or Relay Output8.
• Mains Status DI: Selects None, Digital Input 1, Digital Input 2… or Digital Input 8.
• DG Status DI: Selects None, Digital Input 1, Digital Input 2… or Digital Input 8.
• Fuel Status DI: Selects None, Digital Input 1, Digital Input 2… or Digital Input 8.
• DG Fail Status DI: Selects None, Digital Input 1, Digital Input 2… or Digital Input 8.
• Cyclic BC Enabled: Enables or disables the cyclic Boost Charge function.
• Cyclic BC Interval: Sets the cyclic BC Interval value.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 206

 • Cyclic BC Start Time: Sets the cyclic BC start time.
• Cyclic BC End Time: Sets the cyclic BC end time.
• Start DG Voltage: Sets the start DG voltage value.
• Batt Capacity Start DG Enable: Enables or disables the battery capacity start DG function.
• Start DG Batt Capacity: Sets the start DG battery capacity value.
• Time Start DG Enable: Enables or disables the time start DG function.
• Voltage Stop DG Enable: Enables or disables the voltage stop DG function.
• Stop DG Voltage: Sets the stop DG voltage value.
• Batt Current Stop DG Enable: Enables or disables the battery current stop DG function.
• Batt Capacity Stop DG Enable: Enables or disables the battery capacity stop DG function.
• MPPT Curr Stop DG Enable: Enables or disables the MPPT current stop DG function.
• DG Running Max Time: Sets the DG running maximum time.
• DG Running Min Time: Sets the DG running minimum time.
• DG WarmUp Enable: Enables or disables the DG Warmup function.
• DG CoolDown Enable: Enables or disables the DG cooldown function.
• Rectwork Soc Threshold: Sets the rectwork soc threshold value.
• Voltage Switch-on Rectifier: Sets the voltage value for switch-on rectifier.
• DG WarmUp Delay: Sets the time value for DG warmup delay.
• DG CoolDown Delay: Sets the time value for DG cool down delay.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 207

Shunts Tab
• Allows you to change the shunts signal full name (name displayed in the Web Interface
menus).
• Allows you to change the shunts signal abbreviation name (name displayed in the local
display menus).
• Allows you to set the shunts parameters.

Figure 101: Shunts Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 208

Procedure
1. To modify the shunt parameters, click on the “Modify/View” button for that shunt.
2. The following window opens.

Figure 102: Setting Shunt Parameters

3. Change the following parameters as desired and click on “Set”.

For Battery Shunts:
• Note that for battery shunts, the Set As option is not displayed.
For DC Shunts:
• Set As (Yes, No):
- Yes: Indicates this shunt input is used.
- No: Indicates this shunt input is not used.
For EIB and SMDU Shunts:
• Set As (Not Used, General, Load, Battery, Source):
- Not Used: Indicates this shunt input is not used.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 209

 - General: Indicates the measurement of the shunt will be displayed and will not
be added to Total DC Load or Total Battery Load.
- Load: Indicates the measurement of the shunt will be displayed and added to the
Total DC Load.
- Battery: Indicates the measurement of the shunt will be displayed and added to
the Total Battery Load and used with Battery Management.
- Source: Indicates the measurement of the shunt will be displayed as source
current and will be added to other sources.
For SMDU+ Shunts:
• Set As (Enabled, Disabled):
- Enabled: Indicates this shunt input is used.
- Disabled: Indicates this shunt input is not used.
• Signal Full Name: Name displayed in the Web Interface menus.
• Signal Abbr Name: Name displayed in the local display menus.
• Full Scale Current: Enter the value of the shunt's full current rating.
• Full Scale Voltage: Enter the value of the shunt's full-scale voltage (at rated current).
• Break Value: Enter the value desired as the reference for the high current alarms (typically
the rating of the breakers or fuses fed by the shunt, if applicable).
• High 1 Curr Limit Alarm: Enter the percentage value of the "Break Value" for alarm.
• High 1 Curr Alarm Severity: Alarm level for this alarm. (See also Table 1 on page 10.)
• High 1 Curr Alarm Relay: Select a relay number to map to this alarm.
“None” means there is no related relay number.
• High 2 Curr Limit Alarm: Enter the percentage value of the "Break Value" for alarm.
• High 2 Curr Alarm Severity: Alarm level for this alarm. (See also Table 1 on page 10.)
• High 2 Curr Alarm Relay: Select a relay number to map to this alarm.
“None” means there is no related relay number.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 210

Power Split Tab
You can configure the advanced power split parameters and associated digital input signals. Refer
to “Power Split Feature” on page 15 and “Power Split Feature” on page 53 for more information on
the Power Split feature.

Figure 103: Power Split Tab

Figure 104: Power Split Settings

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 211

Procedure
1. Select the power split mode (enabled or disabled). Click on SET.

Procedure
If low voltage disconnect functions are to be used in a power split configuration, they must be
implemented in the existing power system and signals from its control unit must be connected to
the NCU.
2. For LVD1, LVD2, and/or LVD3; click on the “Modify” button and select the NCU digital
inputs connected to the low voltage disconnect control circuits.

Procedure
If the battery test function is to be used in a power split configuration, battery test must be
implemented in the existing power system and a test signal from its control unit must be connected
to the NCU.
3. For BATTERY_TEST, click on the “Modify” button and select the NCU digital input
connected to the existing systems battery test control circuit.

Procedure
If the equalize charge function is to be used in a power split configuration, equalize charge must be
implemented in the existing power system and an equalizing signal from its control unit must be
connected to the NCU.
4. For EQUALIZE_CHARGE, click on the “Modify” button and select the NCU digital input
connected to the existing systems equalize control circuit.
Monitor Protocol Tab
You can select "EEM", "YDN23", “Modbus “, or “TL1 “as the protocol. To make the new protocol
valid, click the “Valid after Restart" button.

Figure 105: Monitor Protocol Tab

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 212

Figure 106: Valid after Restart

EEM Protocol
You can set EEM protocol parameters.

Figure 107: EEM Protocol

• Protocol Type: Select EEM, RSOC, or SOC/TPE per site requirements.

• Protocol Media: Select RS-232, Modem, IPV4, or IPV6 per site requirements.
• Port Parameter: Enter the port parameters per site requirements.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 213

 • Callback Enabled: Select per site requirements.
• Report Enabled: Select per site requirements.
• CCID: Enter value per site requirements.
• Maximum Alarm Report Attempts: Enter value per site requirements.
• Call Elapse Time: Enter value per site requirements.
• Safety Level: Select per site requirements.
YDN23 Protocol
You can set YDN23 protocol parameters.

Figure 108: YDN23 Protocol

• Protocol Media: Select RS-232, Modem, or IPV4 per site requirements.

• Self Address: Enter the parameter per site requirements.
Modbus Protocol
You can set Modbus protocol parameters.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 214

Figure 109: Modbus Protocol

• Protocol Media: Select RS-232, Modem, or IPV4 per site requirements.

• Self-Address: Enter the parameter per site requirements.
TL1
You can set TL1 parameters.

Figure 110: TL1 Protocol

• Port Activation: Enables or Disables the port activation.

• Protocol Media: Selects the protocol media: IPV4 or IPV6.
• Access Port: Sets the access port.
• Port Keep-alive: Enables or Disables the port keep-alive.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 215

 • Session Timeout: Sets the session timeout value.
• Auto Login User: Selects the auto login user.
• System Identifier: Type in the system identifier.
Clear Data Tab
Select the data log to be cleared from those listed in the drop-down list box. Click on the “Clear”
button to clear the corresponding data.

Figure 111: Clear Data

TL1 AID Group

In Monitor Protocol tab, select ‘TL1’ as the protocol, as shown in the following:

Figure 112: TL1 Protocol

The TL1 AID Group appears, select the TL1 AID Group tab, the AID Group appears, user can edit the
AID name, choose AID type and set the Sub AID Name Prefix. As shown in the following:

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 216

Figure 113: TL1 AID Group

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 217

ACCESSING THE CONTROLLER VIA A NETWORK
MANAGEMENT SYSTEM (NMS)
General
The controller has an SNMP agent function.
Users can use a Network Management System (NMS) to perform the following operations:
• Query the operation status and input/output signals of the devices connected to the
controller.
• Browse the active alarms.
When the controller generates alarms, the SNMP agent can be configured to notify the NMS
through TRAPS automatically.

NMS Supported by SNMP Agent

SNMP is a technology used for network management. The technology is based on implementing an
information base called MIB (Managed Information Base). This MIB contains parameters that are
of interest from a management perspective. All LAN connected equipment that supports SNMP
also supports a default MIB called MIB-II.
The SNMP Agent responds to requests received via the SNMP protocol and also actively sends
TRAPS to a specified manager when certain MIB values change state. This is used to actively inform
a manager when an alarm situation is recognized.
NMS Supported by SNMP v2
The SNMP agent of the controller supports SNMPv2.
All the NMS that supports SNMPv2c can be used to access the controller. The NMS includes HP
OpenView, IBM NetView, Novell ManageWise, SunNet Manager, and so on.
NMS Supported by SNMP v3
The NCU has SSL and SNMP V3 function, which makes the NCU more powerful and more secure.
With SSL, you can browse/set the Webpage with https. If your site requires secure HTTP and you
were furnished with an NCU configuration with secure HTTP, enter https:// and the controller’s IP
address and press ENTER. Data is encrypted in the transmission. You can also browse/set the MIB
library with SNMP v3. Data is also encrypted in the transmission.

SNMP V3

IE Browser MIB Browser

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 218

Parameter Setting in SNMP Manager

The User permitted to access the agent.

The get/set data security level

(NoAuthNoPriv, AuthNoPriv, or
AuthPriv).
The private DES password used to
encrypt the data.

The authorization MD5 password

used to encrypt the digital signature.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 219

 MIB Installation
Installation
The Controller’s MIB is named "Netsure-NCU.mib". Contact your NOKIA representative for the
location on the Web to download the MIB file.
Use the MIB loading function of the NMS to load the MIB database. Refer to the User Manual
provided with the NMS for the detailed loading method.
Contents of the Controller’s MIB
The contents of the MIB supported by the controller's SNMP agent and the OID are listed in Table 6.
For the details, refer to the MIB file named "Netsure-NCU.mib".

Accessing the Controller through an NMS

Apply Administrative Privilege
In order to use the NMS to manage the devices connected to the controller, the administrative
authority needs to be applied for the NMS, that is, add the NMS information to the access list of
SNMP agent.
Add NMS through Web Browser
Refer to “NMSV2 Configuration Description (Network Management System)” on page 188 and
“NMSV3 Configuration Description (Network Management System)” on page 190 for the method of
adding NMS.

ESR Configure
The EEM Protocol is used for communication between the Main Computer and the controller. The
Main Computer is the computer superior to the NCU (the client of the NCU). On this page, all
parameters needed for communication with a main EEM computer are to be set.
User Information Configuration: On this page, Users, their privilege and password are configured.
Time Synchronization: On this page, the system time and date are to be set.
Automatic time synchronization from time servers can also be configured.

Table 6: Contents of the Controller’s MIB

Table 6

Ident Group

identManufacturer The name of the equipment manufacturer. R

identModel The manufacturers model designation of the power system. R
identControllerFirmwareVersio The firmware (software) version of the controller.
n R

The name of the power plant. This object should be set by

identName R/W
the administrator.
identSNMPCfgVer SNMP configuration version. R

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 220

Table 6
identControllerSerialNumber Controller serial number. R

System Group

Status of the complete plant (highest alarm). One of...

(1) unknown - status has not yet been defined
(2) normal - there are no activated alarms
(3) warning - OA, lowest level of 'abnormal' status
(4) minor - A3
systemStatus (5) major - MA R
(6) critical - CA, highest level of 'abnormal' status
(7) unmanaged
(8) restricted
(9) testing
(10) disabled
systemVoltage System voltage, stored as mV. R
systemCurrent System current, stored as mA. R
systemUsedCapacity Used capacity, stored as percentage of the total capacity. R

psBattery Group

psBatteryVoltage Battery voltage, stored as mV. R

psTotalBatteryCurrent Battery current, stored as mA. R
psBatteryCapacity Calculated capacity, stored as % of the total capacity. R
psBatteryNominalCapacity Nominal installed capacity, stored as mAh. R

Battery Table

psBatteryTable Battery table. R

psBatteryEntry Battery measurement table entry. R
psBatteryIndex Automatically generated index object. R
psBatteryCurrent Battery current in amps. R
psBatteryName Battery shunt name. R

psInput Group

psInputLineAVoltage The AC line A voltage, stored as mV. R

psInputLineBVoltage The AC line B voltage, stored as mV. R
psInputLineCVoltage The AC line C voltage, stored as mV. R

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 221

Table 6

psTemperature Group

psTemperature1 The first route temperature, stored as 0.001 Celsius degree. R

The second route temperature, stored as 0.001 Celsius
psTemperature2 R
degree.

Temperature Table

psTemperatureTable Temperature measurement table. R

psTemperatureEntry Temperature measurement table entry. R
psTemperatureIndex Temperature probe number. R
psTemperatureMeasurement Temperature value in centigrade. R
psTemperatureName Configured temperature probe name. R
Temperature Probe Type.
(1) none
psTemperatureType R
(2) ambient
(3) battery
Temperature Probe Alarm Status.
(1) high
psTemperatureAlarmStatus (2) low R
(3) fail
(4) none
The status of communication with the Power System.
(1) unknown
psStatusCommunication (2) normal R
(3) interrupt indicates some errors occurred between Power
System and agent

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 222

Table 6

Battery Mode

The status of battery modes.

(1) unknown
(2) FloatCharging
(3) ShortTest
(4) EqualizeChargingForTest
(5) ManualTesting
(6) PlanTesting
psStatusBatteryMode R
(7) ACFailTesting
(8) ACFail
(9) ManualEqualizeCharging
(10) AutoEqualizeCharging
(11) CyclicEqualizeCharging
(12) PowerSplitEqualizeCharging
(13) PowerSplitBatteryTesting

SM Series Group

psSMACNumber The number of SM AC module. R

psSMBATNumber The number of SM BAT module. R
psSMIONumber The number of SM IO module. R

Rectifier Group

psNumberOfInstalledRectifiers Number of rectifiers. R

psNumberOfRectifiersCommun Number of rectifiers communicating.
icating R

psRectifiersUsedCapacity Used capacity, stored as % of the total capacity. R

Rectifier Table

psRectifierTable Table holding information about individual rectifier. R

psRectifierEntry An entry (conceptual row) in the rectifier info table. R
psRectifierIndex Automatically generated index object. R
PsRectifierProductNumber Rectifier product number. R
PsRectifierHWVersion Rectifier hardware revision. R
psRectifierSWVersion Rectifier software revision. R
psRectifierSerialNumber Rectifier serial number. R
psRectifierCurrent Rectifier current. R

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 223

Table 6
psRectifierIdent Rectifier physical location identifier. R
The type of alarm change. One of…
psRectifierFail (1) Activated R
(2) Deactivated

The Distribution

psTotalLoadCurrent Total load current, stored as integer. R

Distribution Load Table

psDistributionLoadTable Table of shunts configured as loads. R

psDistributionLoadEntry Distribution measurement table entry R
psDistributionLoadIndex Automatically generated index object. R
psDistributionLoadCurrent Distribution current in amps. R
psDistributionLoadName Distribution name. R

Distribution General Table

psDistributionGeneralTable Table of non-load shunts. R

psDistributionGeneralEntry Distribution measurement table entry. R
psDistributionGeneralIndex Automatically generated index object. R
psDistributionGeneralCurrent Distribution current in amps. R
psDistributionGeneralName Distribution name. R

Converter Group

numberOfInstalledConverters Number of converters. R

numberOfConvertersCommuni
cating Number of converters communicating. R

convertersUsedCapacity Used capacity, stored as % of the total capacity. R

psConverterVoltage Converter voltage in mV. R
psTotalConverterCurrent Total converter current in amps. R

Converter Table

psConverterTable Table holding information about individual converters. R

psConverterEntry An entry (conceptual row) in the converter info table. R
psConverterIndex Automatically generated index object. R
psConverterProductNumber Converter product number. R
psConverterHWVersion Converter hardware revision. R

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 224

Table 6
psConverterSWVersion Converter software revision. R
psConverterSerialNumber Converter serial number. R
psConverterCurrent Converter current. R
psConverterIdent Converter physical location identifier. R
The type of alarm change.
psConverterFail (1) activated R
(2) deactivated

Control Group

controlBatteryTest Control battery test, start (1), stop (0). R

controlRelay8 Control relay8, close (1), open (0). R
controlRelay7 Control relay7, close (1), open (0). R
controlRelay6 Control relay6, close (1), open (0). R
controlRelayTest Control relay test, start (1), stop (0). R

Equipment Signal Table

psEquipmentSignalTable Table of indexed equipment signal values. R

equipmentSignalTableEntry An entry (conceptual row) in the equipment signal table. R
psEquipmentSignalTableEntryI The unique sequence number of this equipment signal.
ndex R

psEquipmentSignalValue Indexed equipment signal value. R

Alarm Trap Counter

The sequence number of last submitted alarm trap, also last

alarmLastTrapNo R
row in alarmTrapTable.

Alarm Trap Table

alarmActiveAlarmTable Table holding information about the currently active alarms. R

activeAlarmEntry An entry (conceptual row) in the alarm trap table. R
alarmIndex The unique sequence number of this alarm trap. R
Date and time when event occurred (local time), including
alarmTime R
timezone if supported by controller.
The type of alarm change. One of...
alarmStatusChange (1) activated R
(2) deactivated

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 225

Table 6
The severity of the alarm. One of...
(1) warning - OA, lowest level of alarm severity
alarmSeverity (2) minor - A3 R
(3) major - MA
(4) critical - CA, highest level of alarm severity
alarmDescription Free-text description of alarm. R
alarmType Alarm type, i.e. an integer specifying the type of alarm. R

Event Traps

An alarm trap is sent when an alarm occurs (activated) or

returns to normal state (deactivated). Alarm traps are logged
in alarmTrapTable. Variables in this trap:
* alarmIndex
The unique sequence number of this alarm trap.
* alarmTime
Date and time when event occurred (local time), including
timezone if supported by controller.
alarmTrap * alarmStatusChange --
(1) activated or (2) deactivated.
* alarmSeverity
Integer describing the severity of the alarm.
* alarmDescription
Free-text description of alarm.
* alarmType
Integer indicating type of alarm.
An alarm trap is sent when an alarm occurs (activated).
Variables in this trap:
* alarmTime
Date and time when event occurred (local time), including
timezone if supported by controller.
alarmActiveTrap * alarmSeverity --
Integer describing the severity of the alarm.
* alarmDescription
Free-text description of alarm.
* alarmType
Integer indicating type of alarm.
An alarm trap is sent when an alarm returns to normal state
(clear, deactivated). Variables in this trap:
* alarmTime
Date and time when event occurred (local time), including
timezone if supported by controller.
alarmCeaseTrap * alarmSeverity --
Integer describing the severity of the alarm.
* alarmDescription
Free-text description of alarm.
* alarmType
Integer indicating type of alarm.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 226

 In Table 6, R means OID is read-only (GET), and R/W means OID can be read and modified
(GET/SET).

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 227

REPLACEMENT PROCEDURES
NCU Replacement
DANGER! Follow all “Important Safety Instructions” found in the documentation provided
with the system the NCU Controller is installed in.
ALERT! NCU CONTROLLER HANDLING.
Installation or removal of the NCU Controller requires careful handling. To avoid possibility of
NCU Controller damage from static discharge, a static wrist strap grounded through a one
megohm resistor should always be worn when handling the NCU Controller. ESD-protective
packaging material must also be used when carrying/shipping the NCU Controller.
NOTE! Depending on your network security settings, when you remove a device that is
connected to your network and assign the same IP address to the replacement device, you
may not be allowed to communicate with the replacement device over the network. Contact
your network administrator for assistance.
The NCU is hot swappable. It can be removed and installed with the system operating and without
affecting the output bus.
Procedure
1. Before performing this procedure, ensure the replacement NCU contains the same
configuration file as the existing NCU. Refer to the Configuration File Part Number
Label on the side of the replacement NCU for the Configuration Part Number (see
Figure 114). If the existing controller is operational, navigate the menus to view its
configuration file (MAIN SCREEN / ESC).

Figure 114: NCU Configuration Label Location

Configuration File
Part Number Label

M830B

Configuration File
Part Number Label
M830D

2. Performing this procedure may activate external alarms. Do one of the following. If
possible, disable these alarms. If these alarms cannot be easily disabled, notify the
appropriate personnel to disregard any future alarms associated with this system
while this procedure is being performed.
3. Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 228

 4. Loosen the captive fastener securing the latch mechanism to the front of the NCU to
be replaced. Pull the latch mechanism away from the NCU (this will retract the latch
mechanism located on the bottom of the NCU). This unlocks the NCU from the shelf.
Refer to Figure 115.
5. Slide the NCU Controller completely from the shelf.
6. Loosen the captive fastener securing the latch mechanism to the front of the
replacement NCU. Pull the latch mechanism away from the NCU (this will retract the
latch mechanism located on the bottom of the NCU).
7. Slide the NCU completely into its mounting position.
8. Push the latch mechanism into the front panel of the NCU, and secure by tightening
the captive fastener. This locks the NCU securely to the shelf.
9. Wait for the controller to finish booting and verify that the complete system operates
normally.
10. Enable the external alarms or notify appropriate personnel that this procedure is
finished.
11. Ensure that there are no local or remote alarms active on the system.

Figure 115: Latch Mechanism on the NCU

M830B
Captive
Fastener

Latch
Mechanism

M830D

Captive
ESC ENT Fastener
Latch
Mechanism

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 229

NCU DIGITAL INPUT AND RELAY OUTPUT
CONNECTIONS
NCU Digital Input Connections
The NCU provides four (4) digital inputs for alarms/events. Screw-pressure type connections are
provided. Wire size range is 28 AWG to 16 AWG. Recommended torque for these connections is
0.19 N-m (1.7 in-lbs.). Refer to Figure 116 for connector location and pin-outs.
Note that some digital inputs may be factory wired to the system.

NCU Relay Output Connections

The NCU provides four (4) sets of Form-C alarm relay dry contact outputs for connection of remote
alarms. Relay contacts are rated for 60 W: 2 A @ 30 VDC or 1 A @ 60 VDC. Screw-pressure type
connections are provided. Wire size range is 28 AWG to16 AWG. Recommended torque for these
connections is 0.19 N-m (1.7 in-lbs.). Refer to Figure 116 for connector location and pin-outs.
Each relay is user configurable for alarm conditions. Alarm relay contacts can be connected to
other monitoring equipment.
Note that some relay outputs may be factory wired to the system.

IB2 (Controller Interface Board) and EIB (Controller Extended Interface Board)
One or more IB2 (Controller Interface Board) and/or EIB (Controller Extended Interface Board) may
be connected to the NCU. The IB2 and EIB provide additional digital inputs and relay outputs. Note
that some digital inputs and/or relay outputs may be factory wired to the system. Refer to your
Power System documentation for IB2 and EIB connections and specifications.

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 230

Figure 116: NCU Digital Input and Relay Output Connections

+ - + - NO C NC NO C NC + - + - NO C NC NO C NC

DI 1 DI 2 DO 1 DO 2 DI 3 DI 4 DO 3 DO 4

Digital Relay Digital Relay

Inputs Outputs Inputs Outputs

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 231

SPECIFICATIONS
Input Voltage Range: 19 VDC to 60 VDC.
Power Consumption, Maximum: 18 W.
Operating Temperature Range: -40 °C to +70 °C (-40 °F to +158 °F).
Relative Humidity: Capable of operating in an ambient relative humidity range of 0% to 90%, non-
condensing.
Environment: The controller is recommended to be used in Pollution of Degree 2. Pollution Degree
2 applies where there is only non-conductive pollution that might temporarily become conductive
due to occasional condensation (such as the office -environment).
Dimensions (H x W x D):
• Model M830B: 43.4 mm x 86 mm x 208 mm
1.65” x 3.41” x 8.33”
• Model M830D: 86.2 mm × 87 mm × 208 mm
3.41” x 3.42” x 8.33”
Weight: < 1 kg (2.2 lbs).
Front Panel Display:
• Model M830B: 128 x 160 Pixels TFT LCD
• Model M830D: 320 x 240 Pixels TFT LCD
Indicators:
• Status (Green)
• Minor Alarm (Yellow)
• Critical / Major Alarm (Red)
Local and Remote Access Passwords: Refer to “Passwords and Privilege Levels” on page 25.
Inputs and Outputs: Connection points provided on controller interface board(s) mounted in the
system. Refer to your system documentation.
Factory Default Setpoints: Refer to the Configuration Drawing (C-drawing) furnished with your
system for a list of factory default values.
Safety and Standards Compliance:
• Electrical: IEC 60950-1, EN 60950-1, UL 60950-1
• EMC: EN 300 386, 2001 Class B; FCC Part 15, Class B
• Environmental: CE; NEBS Level 3
• GR-3108 Class 2 Compliant
Temperature Probe Accuracy:
• Calibration Error (-25 °C to +105 °C): ±2 °C

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 232

 • Nonlinearity (-25 °C to +105 °C): 0.4 °C
NCU Temperature Probe Input Accuracy (-10 °C to +65 °C): ±2 °C

Nokia NCU/M830B User Manual (UM1M830B) | Rev. A 233