Scribd
Upload
2 views

Update log

The document outlines the release notes for various versions of a firmware, detailing bug fixes, feature additions, and optimizations. Key improvements include power-loss recovery, Linear Advance and Input Shaping functions, and enhancements to UI and print settings. Each version addresses specific issues to improve overall functionality and user experience.

Uploaded by

secretgalatea
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
2 views

Update log

The document outlines the release notes for various versions of a firmware, detailing bug fixes, feature additions, and optimizations. Key improvements include power-loss recovery, Linear Advance and Input Shaping functions, and enhancements to UI and print settings. Each version addresses specific issues to improve overall functionality and user experience.

Uploaded by

secretgalatea
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

V3.0.

Fixing power-loss recovery issue.


=========================================
V3.0.2

Added Linear Advance and Input Shaping functions.


Fixed the issue where removing the TF card during printing preheating did not
immediately trigger a popup.
Fixed the problem where stopping the print after pausing did not return to the main
interface.
Fixed the issue where removing the TF card after pausing the print did not prompt a
message.
Optimized resume from outage function.
Fixed the problem of no abnormal popup when homing fails.
Optimized the startup sound to be less abrupt.
Fixed the issue where, after pausing the print for 45 seconds, the actual nozzle
temperature gradually decreased. Clicking "stop printing" did not reset the target
temperature of the nozzle and heated bed, keeping it in the previous paused state.
When selecting a file to print again, the actual nozzle temperature decreased, and
clicking the settings page could not return to the status page.
Fixed the issue where, after performing filament retraction, clicking "print"
without homing caused the Z-axis to move downward until it pressed down on the
platform.
Fixed the cumulative time issue on the resume printing popup page during power-off
resume printing.
=========================================
V2.9.3

Serial heating.
Optimized power-off resume voltage detection and first layer not triggering.
=========================================

V2.8.8

Added factory reset function to the UI.


Improved icon prompts for "Z-axis compensation" adjustment in the print settings
page.
Optimized fan adjustment method in the print settings page.
Optimize the Z-axis not to lift when stopping printing.
=========================================

V2.8.7

Optimized handling of calibration module exceptions.


Improved speed mode adjustment method in the UI print settings page.
=========================================

V2.8.6

Optimized UI.
Optimized X-axis coordinate during filament feeding.
=========================================

V2.8.5

Fixed issue with the mainboard fan starting on boot-up.


Fixed issue with UI sound settings not being saved (requires flashing UI firmware).
Fixed cursor display issue on the calibration page (requires flashing UI firmware).
Fixed issue with bed heating when manually leveling after auto-leveling.
Fixed issue where the nozzle continued to heat and smoke when "max temperature
error" occurred and the MOSFET was not closed.
Fixed flashing effect caused by rapid refresh interval between "Probing" and
"Leveling Complete" during "Module" calibration.
Fixed issue where "-" and "." characters could be entered using the UI keyboard
(requires flashing UI firmware).
Fixed various other UI issues (requires flashing UI firmware).
=========================================

V2.8.4F

Enabled fan during leveling to dissipate heat from the print head and reduce the
impact of proximity switch heat radiation.
=========================================

V2.8.4E

Set temperature to 0 before leveling extrusion to optimize heating abnormalities.


Increased XY homing speed from 40mm/s to 80mm/s to determine if it increases the
probability of offset issues.

You might also like