Dust Extraction System

1 System DE - 1 DE - 2
2 Location
2.1 Total Number Of Units
2.2 Type Pulse Jet Pulse Jet
2.3 Application Dust Extraction Dust Extraction
2.4 Dust to be handled Coal Dust Coal Dust
2.5 Flow rate m3/hr 10000 6000
2.6 Gas temperature (Minimum) ‹C 100 100
2.7 Gas temperature (Maximum) ‹C 130 130
2.8 Gas pressure at BF inlet mmwc +/- 500 +/- 500
2.9 Inlet dust load gm/Am3 50 50
2.10 Moisture in gas % V/V 7 7
2.11 Type of dust (Main Characteristic) Fine Fine
2.12 Dust Min bulk density for RAV sizing Kg/m3 800 800
2.13 Dust size distribution Fine Fine
2.14 Instrumentation air Nm3/hr 20 15
3 Technical data sheets for Bag filter
3.1 MODEL
3.2 Type of filter Pulse Jet Pulse Jet
3.3 Filter mounting Snap Band Snap Band
3.4 Filter cleaning Pulse Jet Pulse Jet
3.5 Gas entry Hopper inlet Hopper inlet
3.6 Design pressure (incl wind load) mmwc  +/- 500 +/- 500
3.7 Delta P across filter mmwc
3.8 Maximum outlet dust emission mg/Nm3 75 75
3.9 Recommended air/cloth ratio m3/min/m2 1.22 1.37
3.10 Offered bag height m 3.6 1
3.11 Offered filtration area m2 136 72
3.12 Offered air-to-cloth ratio m3/min/m2 1.22 1.37
3.13 Selected filter Filter Bag Filter Bag
3.14 Number of bags offered no 80 36
3.15 External painting of filter- Primer Red Oxide Red Oxide
3.16 External painting of filter- Finish Enamel Enamel
3.17 External surface preparation of filter Wire Brush Wire Brush
3.18 External paint spec of filter- Primer Wire Brush Wire Brush
3.19 External paint spec of filter- Finish Wire Brush Wire Brush
3.2 Internal painting of filter Red Oxide Red Oxide
3.21 Internal surface preparation of filter Wire Brush Wire Brush
3.22 Internal paint spec of filter
3.23 Size L x W x H 2.1 X 2.5 X 14.3 1.7 X 1.7 X 1.8
4 Bag Filter casing
4.1 MOC IS 2062 IS 2062
4.2 Thickness mm 3.15 3.15
4.3 Condition of supply Assembling Assembling
5 Bag Filter Tube sheet
5.1 MOC IS 2062 IS 2062
5.2 Thickness mm 5 5
5.3 Bag holding method Snap Band Snap Band
6 Bag Filter top covers
6.1 MOC IS 2062 IS 2062
6.2 Thickness mm 3.15 3.15
6.3 Condition of supply Assembling Assembling
7 Bag Filter Hopper
7.1 Type Conical N.A
7.2 MOC IS 2062 N.A
7.3 Thickness 5 N.A
7.4 Condition of supply Assembling N.A
7.5 No. of hoppers no 1 N.A
7.6 Hopper plate angle o 63 N.A
7.7 Hopper discharge opening 250 mm N.A
8 Support structure 1mtr below RAV
8.1 Type of Mounting Below Hopper N.A
8.2 Ground clearance
8.3 Ladder to filter top Provided Provided
8.4 Railing on filter top Provided Provided
9 Filter bags
9.1 Fabric material PNF Pleated
9.2 Bag length m 3600 1000
9.3 Bag fabric weight gm/m2 800 800
9.4 Fabric design temperature (Max.) ‹C 130 130
9.5 Antistatic treatment Yes Yes
9.6 Type Snap Band Snap Band
10 Cages
10.1 Vertical wire dia mm 3 3
10.2 Ring wire dia mm 3 3
10.3 No of vertical wires no 14 14
10.4 Number of splits 15 15
10.5 Cage surface treatment GI GI
10.6 Material of construction MS MS
10.7 Cage diameter mm 150 150
11 Pulse solenoid valve
11.1 Make
11.2 Size Inch 1.5 1
11.3 Operating voltage V AC 230 230
11.5 Quality of compressed air required
12 Sequential Controller
12.1 Operation requirement Pulsing Pulsing
12.2 Type Timer Timer
12.3 Make
12.4 Type of output Relay Relay
12.5 Housing box make
12.6 Housing box protection PVC PVC
12.7 Control voltage V AC 85-270 85-270
13 RAV
13.1 Quantity no 1 1
13.2 MOC MS MS
13.3 Type Square Square
13.4 Drive arrangement Chain Chain
13.5 Motor Make
13.6 RAV rotor speed RPM 1440 1440
13.7 Recommended Size
13.8 Motor HP 0.5 0.5
13.9 Voltage V 415 415
13.10 Frequency HZ 50 50
14 Fan
14.1 Type ID ID
14.2 Casing Material IS 2062 IS 2062
14.3 Impeller Material IS 2062 IS 2062
14.4 Make
14.5 Number Of Fans Nos. 1 1
14.6 Static Pressure mmwg 350 300
14.7 Total Pressure
14.8 Fan Speed Rpm 1440 1440
14.9 Motor Rating HP /RPM 20 12.5
15 Ducting
15.1 MOC/Thickness IS 2062/3.15mm IS 2062/3.15mm
 DE - 3

Pulse Jet
Dust Extraction
Coal Dust
4000
100
130
+/- 500
50
7
Fine
800
Fine
10

Pulse Jet
Snap Band
Pulse Jet
Hopper inlet
+/- 500

75
1.37
1
48
1.37
Filter Bag
24
Red Oxide
Enamel
Wire Brush
Wire Brush
Wire Brush
Red Oxide
Wire Brush

1.15 X 1.15 X 1.6

IS 2062
3.15
Assembling

IS 2062
5
Snap Band

IS 2062
3.15
Assembling

N.A
N.A
N.A
N.A
N.A
N.A
N.A

N.A

Provided
Provided

Pleated
1000
800
130
Yes
Snap Band

3
3
14
15
GI
MS
150

1
230

Pulsing
Timer
 Relay

PVC
85-270

1
MS
Square
Chain

1440

0.5
415
50

ID
IS 2062
IS 2062

1
310

1440
10

IS 2062/3.15mm