Jazz 4G MIFI

Quick Start Guide

1
1. Prepare
 A valid nano-SIM card.

 View the label on your device to get the default information.

The following figure is for reference only.

2
2. Insert the nano-SIM Card and
the Battery
1. Open the back cover.

2. Insert the nano-SIM card.

3
3. Insert the battery

4. Put the cover back.

4
3. Start Your Device
Press and hold the power key for about 3 seconds to power on
the device. After a moment the device will connect to the Internet
automatically.

NOTE:
If the battery is extremely low, you may be unable to power on
the device, please charge your device first.

5
4. Access the Internet
 Wi-Fi: Get the default SSID and password on the label and
connect to the Wi-Fi network with your mobile device, and
then access the Internet.

NOTE:
Please make sure that your phone supports QR code scanning
function and enable Wi-Fi. Use your phone to scan the QR code
on the label and follow the prompts to connect to the Wi-Fi
network of your device.

6
 micro-USB cable: Connect with the computer via USB port
and then access the Internet.

NOTE:
If the operating system does not automatically launch installation,
you can double-click the device installation icon in the virtual CD-
ROM to install the software.

7
5. Change Your Device Settings
You can change the device settings by logging in to the Jazz 4G
MIFI configuration web page.
1. View the label on your device to get the default device
manager Website IP address and Password.
2. Launch the Internet browser and enter the device manager
Website IP address in the address bar.
3. Input the password and then click Login.
4. After the Jazz 4G MIFI configuration web page is opened,
you can change the Wi-Fi SSID, password or other settings.

8
Indicator Lights and Interfaces

9
 Press and hold for 3 seconds to activate the
1 WPS key
WPS function.

Press and hold for about 3 seconds to power

2 Power key
on/off your device.

Network Red: The device is in error status.

3
 The device is not registered to the mobile
network.
 There is no nano-SIM card inserted.
 There is no network service available.
Green solid: The device is registered to the
2G/3G mobile network.
Green blinking: The device is connected to the
2G/3G mobile network and data is being
transferred.
White solid: The device is registered to the LTE
network.
White blinking: The device is connected to the
LTE network and data is being transferred.

Wi-Fi White solid: Wi-Fi is active.

4
White blinking: WPS is active.
Off: Wi-Fi is off.

Battery Red solid/blinking: The battery is low. Please

5
charge the battery.
White blinking: The battery is being charged.
White solid: The battery level is middle or high.
Off: The battery isn’t inserted. Your device is
powered off and not being charged.

10
 Charging/micr Charge the device or connect to the USB port
6
of a computer.
o-USB jack

*RESET hole: Open the back cover, find this hole and then press and
hold for about 3 seconds to restore the device to the factory settings.

11
Troubleshooting

Problem Recommended Action

The  Install the software manually. Please
connection run the installation program in the
between your virtual CD-ROM.
device and a  If the driver of your device is
PC through a abnormal, reinstall the software. You
micro-USB need to uninstall the software first.
cable cannot
be established
automatically.
The  Ensure that the Wi-Fi function is
connection enabled.
between your  Refresh the network list and select
device and a the correct SSID.
client through  Check the IP address, and ensure
Wi-Fi cannot that your client can automatically
be obtain an IP address.
established.  Enter the correct network key (Wi-Fi
password) when you connect the
client to your device.

12
Troubleshooting

Problem Recommended Action

The client  Ensure that your nano-SIM card is
connected to available.
the device  Change the location and find a place
cannot access with good signal.
the Internet.  Check the settings of the WAN
connection mode.
 Contact your service provider and
confirm your APN settings.
The Jazz 4G  Enter the correct address. Please
MIFI view the label on your device to get
configuration the default Device Manager Website
page cannot IP address.
be visited.  Use only one network adapter in your
PC.
 Do not use any proxy server.

13
Get More Help
You can get help by:

• Sending an email to [email protected]

• Visiting https://www.ztedevices.com

14
LEGAL INFORMATION
Copyright © 2021 ZTE CORPORATION.
All rights reserved.
No part of this publication may be quoted, reproduced, translated
or used in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without the prior written
permission of ZTE Corporation.
Notice
ZTE Corporation reserves the right to make modifications on print
errors or update specifications in this guide without prior notice.
Disclaimer
Images and screenshots used in this guide may differ from the
actual product. Content in this guide may differ from the actual
product or software.
Trademarks
ZTE and the ZTE logos are trademarks of ZTE Corporation.
Other trademarks and trade names are those of their respective
owners.

Version No.: R1.0

15
Warning and Notice
To the User
• If inadequately shielded, some electronic devices, for example,
the electronic system of vehicles, may be affected by the
electromagnetic interference caused by the device. Consult
the manufacturers of such devices before using the device if
necessary.
• Operating the device may interfere with medical instruments
such as hearing aids and pacemakers. Always keep the
device more than 20 centimeters away from such medical
instruments when your device is powered on. Power off the
device if necessary. Consult a physician or the manufacturers
of medical instruments before using the device if necessary.
• Be aware of the usage limitation when using the device at
places such as oil warehouses or chemical factories, where
there are explosive gases or explosive products being
processed. Power off the device if necessary.
• Do not use electronic transmission devices in aircraft, at petrol
stations or in hospitals. Observe and obey all warning signs,
and power off the device in these conditions.
• Do not touch the inner antenna area unless necessary.
Otherwise the performance of the device may be affected.
• Do not use the device in an enclosed environment or where
heat dissipation is poor. Prolonged work in such space may
cause excessive heat and raise ambient temperature, which
may lead to automatic shutdown of the device for your safety.
In the case of such an event, cool the device in a well-
ventilated place before turning on for normal use.
• Keep the device out of the reach of small children. The device
may cause an injury if used as a toy.
16
• When the device is operating, do not touch the metallic parts.
Failing to do so may cause burns.
• Use original accessories or accessories that are authorized.
Using any unauthorized accessories may affect the
performance of the device and violate the related national
regulations about telecom terminals.
• Avoid using the device near or inside metallic constructions or
establishments that can emit electromagnetic waves, because
signal reception may be affected.
• The device is not waterproof. Keep the device dry and store it
in a shady and cool place.
• Do not use the device immediately after a sudden temperature
change, because dew may be generated inside and outside
the device. Do not use it until it becomes dry.
• Handle the device carefully. Do not drop, bend or strike it.
Otherwise the device may be damaged.
• Only qualified personnel can dismantle and repair the device.
• The humidity between 5% and 95% is recommended.
• Do not connect the charger while using the device for a long
period. Failing to do so will trigger the protection mechanism
of the battery, and the battery will not be charged. If you want
to charge the battery, please reconnect the charger.
• Do not connect the charger while using the device for a long
period or use the device and battery in non-operating
temperature. Failing to do so will shorten battery life or cause
battery swelling or leakage. If the battery shows signs of
swelling or leakage, please stop use immediately.
• For pluggable equipment, the socket-outlet shall be installed
near the equipment and shall be easily accessible.

17
Battery Safety
• Using ZTE-unapproved or incompatible battery, charger or
power adapter may damage your device, shorten its lifespan
or cause a fire, explosion or other hazards.
• The recommended operating temperatures are 0 °C to 35 °C
and the storage temperatures are -20 °C to +45 °C. Extreme
temperatures can damage the device and reduce the charging
capacity and lifespan of your device and battery.
• Do not place the device or the battery in or near heating
equipment, such as microwave ovens, stoves or radiators.
Keep the device and the battery away from excessive heat and
direct sunlight. If not, the device or the battery may overheat
and cause explosion or fire.
• Please disconnect the charger when the battery is fully
charged. Overcharging may shorten the battery life.
• Do not short-circuit the battery, as this can cause excessive
heat and fire.
• Do not throw the battery into a fire to avoid explosion.
• Do not disassemble, squeeze or puncture the battery, as this
can cause explosion or fire.
• When not using the battery for a long period, please charge
the battery about half then remove the battery from your
device and store it in a cool dry place.
• If the battery damages or shows signs of swelling or leakage,
please stop use immediately and contact ZTE or ZTE
authorized service provider for replacement.
• Return the worn-out battery to the provider or put it in the
designated recycle place. Do not put it in household waste.
• There is a risk of explosion if the wrong battery model is
replaced.

18
 WARNING!
• If the battery is broken, you should avoid contact with the
contents inside. If they contaminate the skin, immediately
rinse with plenty of water and seek medical help when
necessary.
Limited Warranty
This warranty does not apply to defects or errors in the product
caused by:
i. Reasonable abrasion.
ii. End users’ failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End users’ mishandling, misuse, negligence, or improper
installation, disassembly, storage, servicing or operation of
the product.
iv. Modifications or repairs not provided by ZTE or a ZTE-
certified individual.
v. Power failures, surges, fire, flood, accidents, and actions of
third parties or other events outside ZTE’s reasonable
control.
vi. Usage of third-party products or usage in conjunction with
third-party products if such defects are due to the combined
usage.
vii. Any other cause beyond the range of normal usage
intended for the product.
End users have no right to reject or return the product, or receive
a refund for the product from ZTE under the above-mentioned
situations.
This warranty is end users’ sole remedy and ZTE’s sole liability
for defective or nonconforming items, and is in lieu of all other
warranties, expressed, implied or statutory, including but not

19
limited to the implied warranties of merchantability and fitness for
a particular purpose, unless otherwise required under the
mandatory provisions of the law.

Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special,
incidental or consequential damages resulting from or arising out
of or in connection with using of this product, no matter whether
or not ZTE had been advised, knew or should have known of the
possibility of such damages, including, but not limited to lost
profits, interruption of business, cost of capital, cost of substitute
facilities or product, or any downtime cost.

20
ZTE CORPORATION
NO. 55, Hi-tech Road South, Shenzhen, P.R.China
Postcode: 518057
21