SA-WGT4D

SERVICE MANUAL AEP Model

UK Model
Ver. 1.2 2016.09
E Model
Australian Model
• SA-WGT4D is the DVD receiver in MHC-GT4D.
• All of the units included in the MHC-GT4D (SA-WGT4D/
SS-GT4DB/remote control) are required to confirm the
operation of SA-WGT4D. Check in advance that you
have all the units.

Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.

Model Name Using Similar Mechanism HCD-GT3D

DVD Mechanism Type CDM90-DVBU204//M

i Optical Pick-up Block Name CMS-S76RFS7G1 or CMS-S76RFS7GP

m
SPECIFICATIONS

Speaker section Disc/USB section FM Tuner section General

Speaker system: Supported bit rate System Power requirements
Subwoofer, Sound Pressure Horn MPEG1 Layer-3: FM stereo, FM superheterodyne AC 120 V – 240 V, 50/60 Hz
Speaker unit 32 kbps – 320 kbps, VBR tuner Power consumption
250 mm, cone type Sampling frequencies Antenna 270 W
Rated impedance MPEG1 Layer-3: FM lead antenna Power consumption (at the Power Saving
4 ohms 32 kHz/44.1 kHz/48 kHz Tuning range mode)
Xvid 87.5 MHz – 108.0 MHz (50 kHz step) For AEP, UK and RU models only:
Inputs
jo
Video codec: Xvid 0.5 W (When “BT STBY” is set
AUDIO/PARTY CHAIN IN (TV) L/R BLUETOOTH section
Bit rate: 4.854 Mbps (MAX) to “OFF”) and [CONTROL FOR
Voltage 2 V, impedance 47 kilohms Communication system
Resolution/Frame rate: HDMI] is set to [OFF].)
TV (ARC) BLUETOOTH Standard version 3.0
Supported audio signal:
720 × 480, 30 fps
Output 3 W 4) (When “BT STBY” is set to
720 × 576, 25 fps “ON” and [CONTROL FOR HDMI]
2-channel Linear PCM BLUETOOTH Standard Power Class 2
Audio codec: MP3 is set to [ON].)
MIC1, MIC2 Maximum communication range
MPEG4 Dimensions (w/h/d) (Approx.)
Sensitivity 1 mV, impedance Line of sight approx. 10 m 1)
File format: MP4 File Format Active subwoofer:
10 kilohms Frequency band
Video codec: 2.4 GHz band (2.4000 GHz – 392 mm × 710 mm × 435 mm
Outputs MPEG4 Simple Profile Speaker unit (left/right):
AUDIO/PARTY CHAIN OUT L/R 2.4835 GHz)
(AVC is not compatible.) Modulation method 480 mm × 108 mm × 134 mm
Voltage 2 V, impedance 1 kilohm Bit rate: 4 Mbps Speaker unit (Sound Bar Style):
VIDEO OUT FHSS (Freq Hopping Spread Spectrum)
Resolution/Frame rate: Compatible BLUETOOTH profiles 2) 960 mm × 108 mm × 134 mm
Max. output level 1 Vp-p, 720 × 576, 30 fps Mass (Approx.)
unbalanced, Sync. negative load A2DP (Advanced Audio Distribution
Audio codec: AAC-LC Profile) Active subwoofer:
impedance 75 ohms (HE-AAC is not compatible.) 23.5 kg
HDMI OUT (TV) AVRCP (Audio Video Remote
DRM: Not compatible Control Profile) Speaker unit (left/right):
Supported audio signal: 2-channel 3.1 kg
Disc player section SPP (Serial Port Profile)
Linear PCM (up to 48 kHz), Dolby 4)
The power consumption of the system
System Supported codecs
Digital will be less than 0.5 W when there is no
Compact disc and digital audio and SBC 3), AAC, LDAC
HDMI section video system HDMI connection and “BT STBY” is set
1)
Connector The actual range will vary depending on to “OFF”.
Laser Diode Properties factors such as obstacles between devices,
Type A (19 pin) Emission Duration: Continuous magnetic fields around a microwave oven, Design and specifications are subject to
USB section Laser Output*: Less than 44.6 μW static electricity, reception sensitivity,
* This output is the value change without notice.
Supported bit rate antenna’s performance, operating system,
WMA: 48 kbps – 192 kbps, VBR, CBR measurement at a distance of software application, etc.
AAC: 48 kbps – 320 kbps, VBR, CBR 200 mm from the objective lens 2)
BLUETOOTH standard profiles
WAV: 16 bit surface on the Optical Pick-up indicate the purpose of BLUETOOTH
Sampling frequencies Block with 7 mm aperture. communication between devices.
WMA: 44.1 kHz Frequency response 3)
Subband Codec
AAC: 44.1 kHz 20 Hz – 20 kHz
WAV: 44.1 kHz/48 kHz Video color system format
Supported USB device NTSC and PAL

DVD RECEIVER
Mass Storage Class
Maximum current
1A
(USB) port
Type A

9-890-674-03
2016I80-1 Sony Corporation
© 2016.09 Published by Sony EMCS (Malaysia) PG Tec
SA-WGT4D
Ver. 1.2

License and Trademark Notice

• is a trademark of DVD Format/Logo Licensing Corporation.
Self-diagnosis Function
• “DVD+RW”, “DVD-RW”, “DVD+R”, “DVD-R”, “DVD VIDEO”, and
the “CD” logos are trademarks. When letters/numbers appear on the TV
screen or in the display panel
• MPEG Layer-3 audio coding technology and patents licensed from The self-diagnosis function is activated to
Fraunhofer IIS and Thomson. prevent the system from malfunctioning, a
• Windows Media is either a registered trademark or trademark of 5-character service number (e.g. C 13 50) with
Microsoft Corporation in the United States and/or other countries. a combination of a letter and 4 digits appears. In
this case, check the following table.
• This product is protected by certain intellectual property rights of
Microsoft Corporation. Use or distribution of such technology outside
First 3 characters Cause and corrective
of this product is prohibited without a license from Microsoft or an
of the service action
authorized Microsoft subsidiary.
number
• “WALKMAN” and “WALKMAN” logo are registered trademarks of
C 13 This disc is dirty.
Sony Corporation.
• Clean the disc with a
• This system incorporates Dolby* Digital. soft cloth.
* Manufactured under license from Dolby Laboratories.
C 31 The disc is not inserted
Dolby and the double-D symbol are trademarks of Dolby
correctly.
Laboratories.
• Restart the system,
• This system incorporates High-Definition Multimedia Interface then re-insert the disc
(HDMI™) technology. The terms HDMI and HDMI High-Definition correctly.
Multimedia Interface, and the HDMI Logo are trademarks or
E XX To prevent a malfunction,
registered trademarks of HDMI Licensing LLC in the United States
(XX is a number) the system has performed
and other countries.
the self-diagnosis
• “BRAVIA” is a trademark of Sony Corporation. function.
• LDAC™ and LDAC logo are trademarks of Sony Corporation. • Contact your nearest
Sony dealer or local
• The BLUETOOTH® word mark and logos are registered trademarks authorized Sony service
owned by Bluetooth SIG, Inc. and any use of such marks by Sony facility and give the
Corporation is under license. Other trademarks and trade names are 5-character service
those of their respective owners. number.
• The N Mark is a trademark or registered trademark of NFC Forum, Example: E 61 10
Inc. in the United States and in other countries.
• Android™ is a trademark of Google Inc.
• Google Play™ is a trademark of Google Inc.
• Apple, the Apple logo, iPhone, and iPod touch are trademarks of • Abbreviation
Apple Inc., registered in the U.S. and other countries. App Store AR : Argentina model
is a service mark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or

i AUS : Australian model

E4 : African model
m
iPhone, respectively, and has been certified by the developer to E12 : 220 – 240 V AC area in E model
meet Apple performance standards. Apple is not responsible for EA : Saudi Arabia model
the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory LA9 : Latin-American model
with iPod or iPhone may affect wireless performance. MY : Malaysia model
• THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL RU : Russian model
PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR
(i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4
VISUAL STANDARD (“MPEG-4 VIDEO”)
jo
AND/OR
(ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM
A VIDEO PROVIDER LICENSED TO PROVIDE MPEG-4
VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL, INTERNAL AND COMMER-
CIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG
LA, L.L.C.
HTTP://WWW.MPEGLA.COM
• All other trademarks are trademarks of their respective owners.
• In this manual, ™ and ® marks are not specified.

2
 SA-WGT4D

NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.

LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.

i
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
m
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
jo
To Exposed Metal
Parts on Set

AC
0.15 μF 1.5 kΩ voltmeter
(0.75 V)

Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

3
SA-WGT4D

TABLE OF CONTENTS

1. SERVICING NOTES ............................................. 5 7. EXPLODED VIEWS

7-1. Side Panel Section .......................................................... 50
2. DISASSEMBLY 7-2. Top Panel Section ........................................................... 51
2-1. Disassembly Flow ........................................................... 11 7-3. Loading Panel, Back Panel Section ................................ 52
2-2. Side Panel R, Assy .......................................................... 12 7-4. CDM Block Section ........................................................ 53
2-3. Top Panel Section ........................................................... 13 7-5. DVD Mechanism Section (CDM90-DVBU204//M) ...... 54
2-4. Loading Panel Section .................................................... 14 7-6. MOTHERBOARD Board,
2-5. CDM Section .................................................................. 15 3CH DAMP Board Section ............................................. 55
2-6. CDM90-DVBU204//M ................................................... 16 7-7. Switching Regulator (SSN-161AD) Section .................. 56
2-7. Service, Optical Device (7G), Wire (Flat Type) ............. 17 7-8. Chassis Section ............................................................... 57
2-8. Cover Back Panel, MOTHERBOARD Board ................ 18 7-9. Front Panel Section ......................................................... 58
2-9. 3CH DAMP Board .......................................................... 19 7-10. SPK CABINET (SW), Allay Cover Section ................... 59
2-10. Chassis Sub ..................................................................... 20 7-11. Handle Section ................................................................ 60
2-11. Regulator, Switching (SSN-161AD)............................... 21
2-12. Front Panel Section ......................................................... 22 8. ELECTRICAL PARTS LIST .............................. 61
2-13. Handle Section, Allay Cover Section ............................. 23
2-14. Loudspeaker (25cm) ....................................................... 23

3. TEST MODE ............................................................ 24

4. ELECTRICAL CHECKS ...................................... 26

5. TROUBLESHOOTING .......................................... 27

6. DIAGRAMS
6-1.
6-2.
Block Diagram - SERVO/USB Section -........................
Block Diagram - MAIN Section -...................................
i
31
32
m
6-3. Block Diagram - AMP Section - ..................................... 33
6-4. Block Diagram
- PANEL, POWER SUPPLY Section - ........................... 34
6-5. Printed Wiring Board
- MOTHERBOARD Board (Component Side) - ............ 36
6-6. Printed Wiring Board
- MOTHERBOARD Board (Conductor Side) - ............. 37
6-7. Printed Wiring Board - 3CH DAMP Board -.................. 38
jo
6-8. Printed Wiring Board - PANEL Board - ......................... 39
6-9. Schematic Diagram - PANEL Board (1/2) - ................... 40
6-10. Schematic Diagram - PANEL Board (2/2) - ................... 41
6-11. Printed Wiring Board
- GESTURE_MODULE PC BOAR Board - .................. 42
6-12. Printed Wiring Board - GESTURE_RGB Board - ......... 43
6-13. Printed Wiring Board - MIC_IR Board - ........................ 44
6-14. Schematic Diagram - MIC_IR Board - ........................... 45
6-15. Printed Wiring Board - RGB_SPLITTER Board - ......... 46
6-16. Schematic Diagram - RGB_SPLITTER Board - ............ 47
6-17. Printed Wiring Board
- SW_RGB_L Board, SW_RGB_R Board - ................... 48
6-18. Schematic Diagram
- SW_RGB_L Board, SW_RGB_R Board - ................... 48

4
 SA-WGT4D
SECTION 1
SERVICING NOTES
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
NOTES ON HANDLING THE OPTICAL PICK-UP
When checking the board, for the electric shock prevention, con-
BLOCK OR BASE UNIT
nect the resistors to respective parts to discharge.
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by Discharge at capacitor (Ref. No C27)
the charged electrostatic load, etc. on clothing and the human body. Discharge method 1
During repair, pay attention to electrostatic break-down and also Connect the resistors to both ends of capacitor (Ref. No. C27) on
use the procedure in the printed matter which is included in the the switching regulator (SSN-161AD) to discharge.
repair parts.
The flexible board is easily damaged and should be handled with – SWITCHING REGULATOR (Conductor Side) –
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused 800 :/5 W
on the disc reflective surface by the objective lens in the optical (for C27)
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

This appliance is classified as a

CLASS 1 LASER product under
IEC 60825-1:2007. This marking Discharge method 2
is located on the rear exterior. When connecting the resistor to both ends of capacitor (Ref.
No. C27) on the switching regulator (SSN-161AD) is difficult,
discharge by connecting the resistor between fuse (Ref. No. F4)
UNLEADED SOLDER and jumper (Ref. No. J26, J24, J94).
Boards requiring use of unleaded solder are printed with the lead- Note: Be careful not to short-circuit, because between the terminal is close.
free mark (LF) indicating the solder contains no lead.

i
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
– SWITCHING REGULATOR (Component Side) –
m
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
jo
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
J26
Unleaded solder is more viscous (sticky, less prone to flow)
F4
than ordinary solder so use caution not to let solder bridges J74
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may J94
also be added to ordinary solder.
800 :/5 W
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure. Discharge at capacitor (Ref. No C18 and C20)
Discharge by connecting the resistor between pin 1, 2 (+VH) and
NOTE OF PERFORMING THE OPERATION CHECK pin 8, 9 (–VH) of connector (Ref. No, CN2) on the switching
When performing the operation check of this unit, be sure to per- regulator board.
form the operation check in the state that heat sink is installed. If – SWITCHING REGULATOR Board (Component Side) –
operating in the state that heat sink is not installed, it is possibility
that become the protect state.

Pin 1 Pin 10

CN2

800 :/5 W

5
SA-WGT4D
Ver. 1.2

Discharge at capacitor (Ref. No C18 and C20) EA : Saudi Arabia model

If having removed the wire from connector (Ref. No, CN1001) LA9 : Latin-American model
on the 3CH DAMP board before discharging by the switching MY : Malaysia model
RU : Russian model
regulator (SSN-161AD), discharge by connecting the resistor
between pin 2, 3 (+VH) and pin 7, 8 (–VH) of connector (Ref. No,
PLAYABLE DISCS
CN1001) on the 3CH DAMP board.
• DVD VIDEO
– 3CH DAMP Board (Component Side) – • DVD-R/DVD-RW in DVD VIDEO format or video mode
• DVD+R/DVD+RW in DVD VIDEO format
• VIDEO CD (Ver. 1.0, 1.1, and 2.0 discs)
• Super VCD
• CD-R/CD-RW/CD-ROM in VIDEO CD format or super VCD
format
Pin 8 Pin 1 • AUDIO CD
CN1001 • CD-R/CD-RW in AUDIO CD format

PLAYABLE FILES ON DISCS/USB DEVICE

• Music: MP3 files1)2) (.mp3), WMA files2)3) (.wma), AAC files2)3)
800 :/5 W (.m4a/.mp4/.3gp), WAV files3) (.wav)
• Video: MPEG4 files4) (.mp4/.m4v), Xvid files (.avi)
MODEL IDENTIFICATION
1)
MP3 (MPEG 1 Audio Layer 3) is a standard format defined by
ISO/MPEG for compressed audio data. MP3 files must be in
MPEG 1 Audio Layer 3 format.
2)
Files with copyright protection (Digital Rights Management)
cannot be played back by the system.
3)
USB device only.
4)
MPEG4 files must be recorded in MP4 file format. Supported
video codec and audio codec are as follows:

i – Video codec: MPEG4 Simple Profile (AVC is not supported.)

– Audio codec: AAC-LC (HE-AAC is not supported.)
m
Note:
– Rear view – • JIG
MODEL NUMBER LABEL When disassembling the set, use the following jig (for front
MODEL NO. / MODELO: SA-WGT4D panel removal).
120-240 V 50/60 Hz 270 W
DVD RECEIVER
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
MM/YYYY
RECEPTOR DE DVD
Only for Mexico / Sólo para México
Homologación No: XXXXXXXXX-XXXX
Modelo: WB115C Marca: Lite-On Technology
HECHO EN MALASIA
jo
Only for Argentina / Sólo para Argentina
In case of repairing, please bring the
entire system set to the service station.
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the MHC-GT4D (SA-WGT4D/SS-
GT4DB/Remote control) are required to confirming operation of
Contiene Módulo CNC ID: X-XXXXX
SA-WGT4D. Check in advance that you have all of the units.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories
CHECKING THE OPERATION AFTER REPAIR
4-584-059-03

After repair completion, connect the “iPod”, “Walkman”, “smart-

PART No. phone” etc. corresponding to this unit, and check the operation of
playback, recording, charge, etc.
Model Part No.
LA9 4-584-059-0[] NOTE OF REPLACING THE MS-476 BOARD
AEP, UK, AUS 4-584-061-0[] When the MS-476 board is defective, replace the LOADING
AR 4-584-064-0[] COMPLETE ASSY (T).
EA 4-584-065-0[]
NOTE OF REPLACING THE COMPLETE MOTHER-
E12 4-584-066-0[] BOARD BOARD, BLUETOOTH MODULE AND RC-S730
E4 4-584-067-0[] (WW)
RU 4-584-069-0[] When the complete MOTHERBOARD board, Bluetooth module
or RC-S730 (WW) are replaced, it is necessary to check that
MY 4-584-070-0[]
pairing is normally performed.
Perform the operation check according to the following procedure.
• Abbreviation
AR : Argentina model
Note: Be sure to delete pairing information after checking the pairing.
AUS : Australian model
E4 : African model
E12 : 220 – 240 V AC area in E model

6
 SA-WGT4D

Pairing this system with a Bluetooth device Playing music from a Bluetooth device
1. Press the [1] button to turn the power on. For a Bluetooth device
2. Place the Bluetooth device within 1 meter (3 feet) from the 1. Press the [1] button to turn the power on.
system. 2. Press BLUETOOTH on the unit to select Bluetooth function.
3. Press BLUETOOTH on the unit to select Bluetooth function. “BT AUDIO” appears in the display panel.
“BT AUDIO” appears in the display panel. 3. Establish connection with the Bluetooth device.
Notes:
Press BLUETOOTH on the unit to connect to the last
• When there is no pairing information on the system, the connected Bluetooth device.
system enters the pairing mode automatically and “PAIRING” Perform the Bluetooth connection from the Bluetooth device if
flashes in the display panel. Proceed to step 5. the device is not connected.
• If the system is connected to a BLUETOOTH device, Once the connection is established, the Bluetooth device name
press BLUETOOTH on the subwoofer to disconnect the appears in the display panel.
BLUETOOTH device. 4. Press N to start playback.
4. Hold down - PAIRING on the unit for 2 seconds or more. Depending on the Bluetooth device,
“PAIRING” flashes in the display panel. – you may have to press N twice.
5. Perform the pairing procedure on the Bluetooth device. – you may need to start playback of an audio source on the
6. Select the model number of the unit on the display of the Bluetooth device.
Bluetooth device.
For example, select “MHC-GT4D”. If passkey is required on For an NFC-compatible smartphone
the Bluetooth device, enter “0000”.
7. Perform the Bluetooth connection on the Bluetooth device. 1. Press the [1] button to turn the power on.
8. When pairing is completed and the Bluetooth connection is Touch the smartphone to the N-Mark on the system to establish
established, the Bluetooth device name appears in the display the Bluetooth connection.
panel. Start playback of an audio source on the smartphone. For
9. To cancel pairing operation, hold down BLUETOOTH on the details on playback, refer to the operating instructions of your
unit for 2 seconds or more until “BT AUDIO” appears in the smartphone.
display panel.

i To disconnect the Bluetooth device

For a Bluetooth device
m
Connecting with a smartphone by one touch (NFC)
Press BLUETOOTH on the unit.
Note: The operation in this mode must use a NFC-compatible smartphone “BT AUDIO” appears in the display panel.
(Smartphones with a built-in NFC function [OS: Android 2.3.3 or
later, excluding Android 3.x]) For an NFC-compatible smartphone
1. Press the [1] button to turn the power on. Touch the smartphone to the N-Mark on the system again.
2. Download and install the app “NFC Easy Connect”.
Download the free Android app from Google Play by searching To erase all the pairing registration information perform
jo
for “NFC Easy Connect”. COLD RESET test mode (Refer page 24).
3. Start the app “NFC Easy Connect” on the smartphone.
Make sure that the application screen is displayed. NOTE OF DISASSEMBLE THE PANEL, SIDE
4. Touch the smartphone to the N-Mark on the system until the To disassemble the PANEL, SIDE, hexagon key is required to
smartphone vibrates. unscrew the SCREW, TAPPING (HEX).

hexagon key

Complete the connection by following the instructions

displayed on the smartphone.
5. When pairing is completed and the Bluetooth connection is
established, the Bluetooth device name appears in the display
panel. hexagon key

7
SA-WGT4D

BOND FIXATION OF ELECTRICAL PARTS

When switching regulator (SSN-161AD) is replaced, fix the
electrical parts by using the bond (SC608Z2).

• Object board
1. REGULATOR, SWITCHING (SSN-161AD) board

• Use bond
Part No. Description
7-600-020-70 ADHESIVE (SC608Z2) 180ML C20 C18

• Parts position
1. REGULATOR, SWITCHING (SSN-161AD) board The portion which applies bond:
(page 8) TEST DISCS
Use following TEST DISC when this unit confirms the operation
1. REGULATOR, SWITCHING (SSN-161AD) board and checks it.
– SWITCHING REGULATOR (Component Side) –
• For CD
Part No. Description
LF1 C17 3-702-101-01 DISC (YEDS-18), TEST
4-225-203-01 DISC (PATD-012), TEST
C8
J-2501-307-A DISC (HLX-A1), TEST

C34 • For DVD SL (Single Layer)

Z1 C3
Part No. Description
J-6090-069-A DISC (HLX-503), TEST (NTSC)
C21 C22 TP1 J-6090-088-A DISC (HLX-504), TEST (NTSC)

i J-2501-305-A
J-6090-077-A
DISC (HLX-513), TEST (NTSC)
DISC (HLX-506), TEST (PAL)
m
• For DVD DL (Double Layer)
Part No. Description
J-6090-071-A DISC (HLX-501), TEST (NTSC)
J-6090-089-A DISC (HLX-505), TEST (NTSC)
T2 J-2501-306-A DISC (HLX-514), TEST (NTSC)
J-6090-078-A DISC (HLX-507), TEST (PAL)
jo
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of sample disc in the
shop is equipped.
It can release the lock function in the following procedure.

T2 Releasing Procedure:
1. Press the [1] button to turn the power on.
2. Press the [FUNCTION] button to turn the DVD/CD function.
3. Press two buttons of the [ENTER] and [VOCAL FADER]
simultaneously for three seconds.
C27
4. The message “UNLOCKED” is displayed on the screen
display panel and the disc tray is unlocked.
Note: When “LOCKED” is displayed on the screen display panel, the
disc tray lock is not released by turning the power on/off with the
[1] button.

IF “PROTECTX” (X IS A
NUMBER) APPEARS IN THE
L1 DISPLAY PANEL
Immediately unplug the AC
power cord (mains lead), and
TP1 check the following items.
ˎ Is anything blocking the
ventilation holes of the
subwoofer?
ˎ Is the USB port short-circuited?
ˎ Are the speaker cords of the
speaker system connected to the
subwoofer properly?
After checking the above items and
fixing any problems, plug in the AC
power cord (mains lead) again and
turn on the system.

8
 SA-WGT4D

HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

Note 1: After the side panel L, R and top panel are removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).

1 Remove the SIDE PANEL L, R, top panel section.

(Illustration of disassembly is omitted.)

3
hole
– Left view –

Insert the clip etc. processed to the

length of 8 cm or more in the hole
on the side of the chassis and push. DVD mechanism 2 Insert the clip etc.
deck

8 cm or more

i
m
tray
Note: Push after it inserts it
in this hole well.
jo
– Top view –

9
SA-WGT4D

SERVICE POSITION

top panel section

MIC_IR board

CDM section
MOTHERBOARD
board

stand

insulating sheet

stand

i insulating sheet BLUETOOTH module

m
3CH DAMP board

REGULATOR,
SWITCHING (SSN-161AD)
jo

10
 SA-WGT4D
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

2-1. DISASSEMBLY FLOW

SET

2-2. SIDE PANEL R, ASSY

(Page 12)

2-3. TOP PANEL SECTION

(Page 13)

2-4. LOADING PANEL SECTION 2-8. COVER BACK PANEL,

(Page 14) MOTHERBOARD BOARD
(Page 18)

2-9. 3CH DAMP BOARD

2-5. CDM SECTION (Page 19)
(Page 15)

2-6. CDM90-DVBU204//M
i 2-10. CHASSIS SUB
m
(Page 20)
(Page 16)

2-11. REGULATOR, SWITCHING

2-7. SERVICE, OPTICAL DEVICE (7G), (SSN-161AD)
WIRE (FLAT TYPE) (Page 21)
(Page 17)
jo
2-13. HANDLE SECTION,
2-12. FRONT PANEL SECTION ALLAY COVER SECTION
(Page 22) (Page 23)

2-14. LOUDSPEAKER (25cm)

(Page 23)

11
SA-WGT4D

Note: Follow the disassembly procedure in the numerical order given.

2-2. SIDE PANEL R, ASSY

Note: The side panel L, assy can be removed in the same manner as the side panel R, assy.

2 two screws
(+BVTP 3 u 10)

side panel L, assy

1 four screws
(tapping (HEX))

3 Slide the side panel R, assy

in the direction of the arrow.

i
m
side panel R, assy
jo

5 side panel R,
assy

4 Remove the side panel R, assy

in the direction of the arrow.

12
 SA-WGT4D

2-3. TOP PANEL SECTION

‡:LUHVHWWLQJ
pin, lead
pin, lead
PANEL board
‡:LUHVHWWLQJ

GESTURE_RGB board

4 Remove the panel, top section

in the direction of the arrow.

2 four screws
0 panel, top (+BVTP 3 u 10)
section

3 one screw cushion (QV, B) GESTURE_RGB

(+BVTP 3 u 10) board

pin, lead PANEL board

holes
Note : When installing the panel, top 5 CN451 (4P)
section, align five panel, front
guides and five holes. 6 wire (flat type) (23 core)
(CN122)
9 CN1101 (7P) 3 one screw

i (+BVTP 3 u 10)
m
8 wire (flat type) (6 core) 7 wire (flat type) (7 core)
(CN105) (CN120)

1 two screws
(+BVTP 3 u 10)

‡:LUHVHWWLQJ
PANEL board
jo

front panel guides

filament tape GESTURE_RGB

(sub material) board

13
SA-WGT4D

2-4. LOADING PANEL SECTION

4 loading panel
section

hole
– Left view –
3 three claws
Insert the clip etc. processed to the
length of 8 cm or more in the hole 2 Draw out the tray.
on the side of the chassis and push. DVD mechanism 1 Insert the clip etc.
deck

8 cm or more

i
tray
m
Note: Push after it inserts it
in this hole well.

– Top view –
jo

14
 SA-WGT4D

2-5. CDM SECTION

‡:LUHVHWWLQJ
CDM section hook pin, lead
3 two screws
(+BVTP 3 u 8)

8 CDM section
3 one screw
(+BVTP 3 u 8)

5 wire (flat type)

(24 core) (CN302)
4 Remove the filament tape
CDM section in (sub material) 3CH DAMP board
6 wire (flat type) the direction of
(5 core) (CN303) the arrow.

7 CN401 (6P)
1 Remove the wire
from pin, lead. 2 Remove the wires
from hook.

i
m
jo

–7RSUHDUYLHZ–

15
SA-WGT4D

2-6. CDM90-DVBU204//M

‡:LUHVHWWLQJ
1 filament tape
(sub material)

bracket CDM section

filament tape (sub material)

– CDM section bottom view –

i 2 four screws
(BVTP3 u 8)
m
8 CDM90-DVBU204//M
jo
5 cushion,
saranet
(30 u 50)

6 core, ferrite

4 Draw two wires out of

the hole in bracket CDM
section.

7 bracket CDM section

3 Draw wire out of
the hole in bracket CDM
section.

–&'0VHFWLRQIURQWYLHZ–

16
 SA-WGT4D

2-7. SERVICE, OPTICAL DEVICE (7G), WIRE (FLAT TYPE)

2 chuck holder assy (T)
1 six claws

qa insulator

8 four insulator screws

qf wire (flat type)
qs service, (5 core)
optical device (7G)

qa insulator
qa insulator qh holder, FFC
0
9
6 belt
7 connector
qj wire (flat type)
qg (24 core)
3 Insert the thin
wire (clip etc.).

i
m
qd base, loading assy (T)
4 lo assy

5 tray –%RWWRPYLHZ–

‡,QVWDOODWLRQRIZLUH IODWW\SH  FRUH DQGZLUH IODWW\SH  FRUH

jo
Note: This illustration sees the loading assy (T) from bottom side.
5 three claws

5 two claws
1 wire (flat type) (24 core)
loading assy (T)

6 holder, FFC
3 Through the hole
4

7 wire (flat type)

(24 core)

terminal face

2 Through the hole

8 wire (flat type)
(5 core)
9 filament tape
Under the guide (sub material)
(Fold area)

Under the guide

17
SA-WGT4D

2-8. COVER BACK PANEL, MOTHERBOARD BOARD

Note: When the complete MOTHERBOARD board is replaced,

refer to “NOTE OF REPLACING THE COMPLETE
MOTHERBOARD BOARD, BLUETOOTH MODULE AND
RC-S730 (WW)” on page 6.

9 five screws
(+BVTP 3 u 8) qs MOTHERBOARD
board

2 cover back panel

1 four screws
(+BVTP 3 u 10)

7 filament tape
(sub material)

3 CN601 (4P)
4 Remove the
wires from
i
m
two clamps.

5 CN001 (9P)
jo
6 wire (flat type)
(10 core) (CN102)
qa one screw
8 wire (flat type) 0 two screws (+B 3 u 6)
(19 core) (CN125) (+BVTP 3 u 8)

– Top rear view –

‡:LUHVHWWLQJ

clamp MOTHERBOARD board

18
 SA-WGT4D

2-9. 3CH DAMP BOARD

6 two screws
(TRANSISTOR)

9 heatsink D-AMP
8 sheet, thermal
2 three screws
2 one screw
(+BVTP 3 u 8)
(+BVTP 3 u 8)

3 clamp

A
qa 3CH DAMP 7 one screw
board (+BVTP 3 u 8)

‡:LUHVHWWLQJ
clamp
qs Remove the bracket
qd bracket heat sink heat sink in the
direction of the arrow.

i 5 CN1001
m
(8P)

3CH DAMP board

4 CN1005 (2P)
jo
A

0 one screw
(+BVTP 3 u 8)

1 CN1004 (2P)

–7RSUHDUYLHZ–

19
SA-WGT4D
Ver. 1.2

2-10. CHASSIS SUB

0 two screws
(+BVTP 3 u 8)

8 two screws
qa fan section (+BVTP 3 u 8)

7 clamp 9 air guide

6 two screws
(+BVTP 3 u 8)
1 two screws
(+BVTP 3 u 8)
7 clamp

5 jack plate
qs sub, chassis
2 two screws
(+BVTP 3 u 8) 4 one screw
(+BVTP 3 u 8)

3 audio
plate
4 two screws
1 two screws
(+BVTP 3 u 8)

i (+BVTP 3 u 8)
m
2 one screw
(+BVTP 3 u 8)
jo

– Top rear view –

20
 SA-WGT4D

2-11. REGULATOR, SWITCHING (SSN-161AD)

‡:LUHVHWWLQJ
REGULATOR,
clamp SWITCHING (SSN-161AD)

3 one screw
(+BVTP 3 u 8)

4 clamp
3 four screws
3 four screws (+BVTP 3 u 8)
(+BVTP 3 u 8)

7 core, ferrite

6 himelon 45

5 REGULATOR,
SWITCHING

i 8 two step
screws
8 two step screws
m
(SSN-161AD)

9 chassis section
jo
1 Remove the wire
‡:LUHVHWWLQJ
core, ferrite from two clamps.

2 CN1
(2P)

REGULATOR, clamp
SWITCHING (SSN-161AD)

– Top rear view –

21
SA-WGT4D

2-12. FRONT PANEL SECTION

2 Insert the jig into a space and slowly 1 one tapping screw
remove the panel, front section. (1) (3.5 x 20)
Note 1: When using a jig, please work
so as not to injure panel, front
section and speaker cabinet.

3 All bosses are removed while moving

jig in the direction of the arrow, and
panel, front section is removed. 2 Insert the jig into a space and slowly
remove the panel, front section.
Note 1: When using a jig, please work
so as not to injure panel, front
section and speaker cabinet.

total fourteen bosses

i 3 All bosses are removed while moving

jig in the direction of the arrow, and
m
panel, front section is removed.
jo
4 Remove the panel, front section
in the direction of an arrow.

5 panel, front section

Note 2: When installing the front panel section,
remove the used glue and use a new
glue to fix the front panel section.

22
 SA-WGT4D

2-13. HANDLE SECTION, ALLAY COVER SECTION

1 one screw
(1) (4 x 20), +BV TAPPING
2 two screws
(1) (4 x 20), +BV TAPPING

4 handle section 2 two screws

(1) (4 x 20), +BV TAPPING
1 one screw
(1) (4 x 20), +BV TAPPING
3 four screws
(+BVTP 3 u 10)

2 two screws
(1) (4 x 20), +BV TAPPING

2 two screws
(1) (4 x 20), +BV TAPPING

5 allay cover
section

i
m
jo
2-14. LOUDSPEAKER (25cm)

‡+RZWRLQVWDOOWKHORXGVSHDNHU FP

terminal position loudspeaker (25cm)

3 terminal
(wide side)

3 terminal (narrow)

1 eight screws
(1) (4 x 20),
+BV TAPPING

4 loudspeaker (25cm) 2 Remove the loudspeaker (25cm)

in the direction of the arrow.

23
SA-WGT4D
SECTION 3
TEST MODE
[PANEL TEST MODE] [COLD RESET]
This mode is used to check the screen display panel, LEDs, keys, The cold reset clears all data including preset data stored in the
GESTURE CONTROL, model, destination and software version. data flash to initial conditions included history mode data. Execute
Procedure: this mode when returning the set to the customer.
1. Press [1] button to turn on the system. Procedure:
2. Press [] button and [TUNING – .] button simultaneously 1. Press [1] button to turn on the system.
and hold 3 seconds. 2. Press [] button and [TUNING + >] button simultaneously
3. All LEDs and segments in screen display panel are lighted up. for 3 seconds.
4. When [ENTER] button is pressed after all LEDs and segments 3. “COLD RST” appears on the screen display panel. After
in screen display panel light up, alternate segments in screen that, the screen display panel will display “SONY”. The set
display panel and LEDs would light up, all Party Light LEDs will automatically Power ON and Power OFF again, and the
would light up in red color. If you press [ENTER] button again, system is reset.
another half of alternate segments in screen display panel and
LEDs would light up, all Party Light LEDs would light up in [DISC TRAY LOCK MODE]
green color. Pressing [ENTER] button again would cause all This mode let you lock the disc tray. When this mode is activated,
segments in screen display panel and LEDs light up, all Party the disc tray will not open when [Z] button is pressed. The message
Light LEDs would light up in blue color. Pressing [ENTER] “LOCKED” will be displayed on the screen display panel. This
button again would turn off all segments in screen display mode only applied when there is disc on the tray.
panel and all LEDs including Party Light LEDs. Procedure:
5. When you want to enter to the software version display mode, 1. Press [1] button to turn on the system.
press [+] button. 2. Press [FUNCTION] button to turn DVD/CD function.
The model information appears on the screen display panel. 3. Press [ENTER] button and [VOCAL FADER] button
Press [+] button again to view the destination information. simultaneously and hold down until “LOCKED” or
6. During the destination information display, press [+] button. “UNLOCKED” displayed on the screen display panel (around
Each time [+] button is pressed, the screen display panel 3 seconds).
shows the version of each category software in the following
sequence: SC, MTK, OPU, UI, PF, SUB, SYS, CD, CMA, Bluetooth PAIRING HISTORY CLEAR
CMB, ST, TA, TM, CEC and return back to model information
display.

i It can clear the Bluetooth pairing history.

Procedure:
m
7. When [] button is pressed while the version numbers are 1. Press [1] button to turn on the system.
being displayed except model and destination, the date of the 2. Press [FUNCTION] button to turn the Bluetooth function.
software creation appears. When [] button is pressed again, 3. Press two buttons of [ENTER] and [–] simultaneously for 3
the display returns to the software version display. seconds.
8. Press [–] button, the key check mode is activated. 4. The message “BT HIST” → “CLEAR” is displayed on the
9. In the key check mode, the screen display panel displays “K0 screen display panel, and the pairing history of Bluetooth is
V0”. cleared.
Each time a button is pressed, “K” value increases. However,
jo
once a button has been pressed, it is no longer taken into [DEMO MODE]
account. After all the buttons have been pressed, “K” value The demo mode can be performed.
will toggle between “OK” and “K27”. (This mode is used by shop front)
“V” value increases in the manner of 0, 1, 2, 3 ... if [MIC Procedure:
LEVEL] knob is turned clockwise, or it decreases in the 1. Press the [1] button to turn the system.
manner of 0, 9, 8, 7 ... if [MIC LEVEL] knob is turned 2. Press two buttons of the [] and [MIC ECHO] simultaneously
counterclockwise. for 5 seconds.
10. To release from this mode, press the buttons in the same 3. The message “AutoPLAY” is displayed on the screen display
manner as step 2, or disconnect the power cord. panel.
4. Press [TUNING + >] or [TUNING – .] to select either
[USER RESET] AutoPLAY or AutoSTOP in Demo mode, then press [ENTER]
The user reset clears all data including preset data stored in the data to make selection.
flash to initial conditions exclude history mode data. 5. Press [TUNING + >] or [TUNING – .] to select reset
Procedure: timer setting, then press [ENTER] to make selection.
1. Press [1] button to turn on the system. 6. Set will power off and power on, after that it will mode into
2. Press [ENTER] button and [TUNING + >] button simulta- Demo mode.
neously for 3 seconds. 7. The message “* DEMO *” is displayed on the screen display
3. “RESET” appears on the screen display panel. After that, the panel.
screen display panel becomes blank for a while, and the system
goes to demo mode. • To release from Demo Mode
1. Press two buttons of the [] and [MIC ECHO]
simultaneously for 5 seconds or perform the “USER RESET”.
Note: The demo mode does not release by unplug the AC cord.

24
 SA-WGT4D

[HISTORY MODE]
This mode is used to check important data stored in the system when PROTECTOR happened.
Procedure:
1. Press the [1] button to turn the power off.
2. During demo mode, press [] button and [+] button for 5 seconds to mode into history mode.
3. Press the [TUNING + >] button or [TUNING – .] button to check history data stored.

Display on screen display panel Description

P C O U N T ※ ※ No. of time protector happened (0 ~ 99)
P T ※ ※ ※ ※ Refer to protect type description
Single Power On Time until protector happened (0~99999 hours,
1 *h *h *h *h *h *m *m
0~99 minutes)
Total Power On Time [ no consider protector happened ]
2 *h *h *h *h *h *m *m
(0~99999 hours, 0~99 minutes)
F ※ ※ ※ ※ ※ ※ Input Function during protector happened
V O L ※ ※ ※ Volume setting (MIN / 1 - 50 / MAX)
S W ※ Subwoofer setting (0 ~ 4)
B A S S ※ ※ ※ MEGA BASS setting (OFF / ON)

To release from History Mode.

To release from this mode, press [1] button.

Protect Type Description:

Error Code Description

i
m
1 The over current condition to MOSFET occurs by defect of MOSFET or defect of PS output line.
or
Unusual heat up of MOSFET by improper assembly of heat sink, destruction of MOSFET etc.
2 Defect of thermistor IC or charging circuit used by SPM (Sound Pressure Management) system.
3 Defect of power supply circuit to AMP. There is possibility of unusual power supply of any of the AMP IC or
Pre-amplifier.
jo
4 DC appears in SP terminal by defect of AMP IC and MOSFET.
6 Defect of DC FAN and DC FAN driver circuit.

If speaker does not have output even if the set status is not in PROTECT mode, the following defect might be possible:

Defects Possible cause

RESET defect Reset signal status from micom is not ‘H’.

[DVD COLOR SYSTEM MODE]

This mode let you change the color system of the video output from PAL to NTSC or vice-versa.
Procedure:
1. Press [1] button to turn on the system.
2. Press [FUNCTION] button to turn DVD/CD function.
3. Press [ENTER] button and [MIC ECHO] button simultaneously and hold for 3 seconds.
4. The message “PAL” or “NTSC” appears on the screen display panel.

• To release from DVD Color System Mode

1. Once the color system has been selected, the mode is fixed there after. If you wish to change the mode again, perform the above item
2 again.

25
SA-WGT4D
SECTION 4
ELECTRICAL CHECKS
TUNER SECTION 0 dB = 1 V Checking Location:

FM TUNE LEVEL CHECK – MOTHERBOARD Board (Component Side) –

signal
generator
unit

Procedure:
1. Press the [1] button to turn the power on.
2. Input the following signal from signal generator to FM antenna
input directly.
pin 1 (GND) pin 17 (RF)
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
CN302
Modulation : 1 kHz
ANT input : 35 dBu (EMF)

Note: Use 75 ohm coaxial cable to connect signal generator and the unit.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.

3. Press the [FUNCTION] button to turn the “TUNER FM”

function and tune A, B and C signals.
4. Check “TUNED” is lit on the screen display panel for A, B and
C signals.

When the selected station signal is received in good condition,

“TUNED” is displayed on the screen display panel.
i
m
DVD SECTION

Note:
1. DVD block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
ed.
3. Use an oscilloscope with more than 10 M impedance.
4. Clean the object lens by an applicator with neutral detergent when the
jo
signal level is low than specified value with the following check.

FOCUS BIAS CHECK

oscilloscope
(DC range)

MOTHERBOARD board
CN302 pin 17 (RF) +
CN302 pin 1 (GND) –

Procedure:
1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302
pin 1 (GND) on the MOTHERBOARD board.
2. Press the [1] button to turn the power on, and press the
[FUNCTION] button to select CD/DVD function.
3. Set the test disc (CD: YEDS-18) on the tray and press [B]
button to playback.
4. Confirm that oscilloscope waveform is as shown in the figure
below (eye pattern).
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.

VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
1.1 ± 0.25 Vp-p (DVDSL)
1.0 ± 0.25 Vp-p (CD)

26
 SA-WGT4D
SECTION 5
TROUBLESHOOTING
Switching Regulator (SSN-161AD) Diagnosis Flow

Connect the AC power cord.

The output voltage from the switching regulator is the following standard value. No
Replace the switching regulator.
Standby Demo mode Power on
CN4:
Between pin 3, 4 (LED) 13.5 V ± 5 % 13.5 V ± 5 % 13.5 V ± 5 %
and pin 5, 6 (LED GND)
CN2:
Between pin 1 to 2 (+PVDD) 0V 0 V 62.5 V ± 5 %
and pin 5 (GND)
CN2:
%HWZHHQSLQWR í39''  0 V 0 V í9“
and pin 5 (GND)
CN2:
Between pin 3 (+VL) 0 V 0 V 17 V ± 5 %
and pin 5 (GND)
CN2:
%HWZHHQSLQ í9/  0 V 0 V í9“
and pin 5 (GND)
CN2:
Between pin 10 (SVP) 0 V 0 V í9“
and pin 5 (GND)

Yes

i
m
End

(1) CN1 (AC power cord connector) – SWITCHING REGULATOR (Component Side) –
(2) F1 (Fuse)
(3) T1 (Sub power transformer) (2)
(4) CN4 (Main power connector) (1)
Pin 1 : Audio
jo
(6)
Pin 2 : Audio GND
Pin 3 : LED
(5)
Pin 4 : LED
Pin 5 : LED GND
Pin 6 : LED GND
Pin 7 : AC-DET
Pin 8 : PCON
Pin 9 : LOW AC (3)
(5) T2 (Main power transformer)
(6) CN2 (Amplifier power connector)
Pin 1 : +PVDD
Pin 2 : +PVDD (4)
Pin 3 : +VL
Pin 4 : GND – SWITCHING REGULATOR (Conductor Side) –
Pin 5 : GND
Pin 6 : GND Pin 1
Pin 7 : –VL
Pin 8 : –PVDD
Pin 9 : –PVDD (6)
Pin 10 : SPV

Pin 10

Pin 9 (4) Pin 1

27
SA-WGT4D

Optical Block Diagnosis Flow

REMOVE SIDE PANEL

REMOVE TOP PANEL
TURN ON
TRAY IN

Checks CL381 for +3.3V and +1.2V

No REG IC303. No Checks IC303 circumference circuit for +1.2V.
Does Optical pickup move to inner
Checks IC009 (JL071) circumference circuit for
circumference? (Visual check) Does it output the power voltage of
+3.3V.
3.3V and 1.2V?
Yes
Yes
Checks CN401 SL+/SL- signal. No Checks circumference circuit for SL+/SL- of IC401.
Does it output the signal? Checks circumference circuit of IC301 FMO Signal.
Yes
The Sled motor has a problem.
Replaces BU.

Does Spindle motor rotate? No Checks CN401 SP+/SP- signal. No Checks circumference circuit for SP+/SP- of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 DMO Signal.

Yes Yes
The Spindle motor has a problem.
Replaces BU.

i
m
Does Optical pickup do focus search? No Checks CN302 FCS+/FCS- signal. No Checks circumference circuit for FCS+/FCS- of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 FOO Signal.

Yes Yes
The Optical pickup has a problem.
Replaces BU.
jo
Checks JL306 FE_LD_CD (780)
Does laser diode become luminous? No signal. No Checks circumference circuit of Q402.
(Visual check) Does it output 2V when laser Checks circumference circuit of IC301 LDO1.
become luminous?
Yes
Yes
DISC IN The Optical pickup has a problem.
Replaces BU.
Yes

Is output level of RF signal (JL317) up No If it is not up to standard,

to standard? Lens cleaning is performed.
RF Level = 1.05 ±0.45 Vpp Yes
Test disc (CD: YEDS-18,
Is output level of RF signal (JL317)
DVD: HLX-503 (NTSC) or HLX-504
up to standard? No
(PAL))
RF Level = 1.05 ±0.45 Vpp Replaces BU if it is not up to standard.
Yes Test disc (CD: YEDS-18, DVD:
HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Is there no problem with Long term
Aging Test (60min)?
Confirms that there is no sound skip. No

Yes
The Optical pickup has a problem.
END Replaces BU.

28
 SA-WGT4D

Gesture Troubleshooting

Gesture operation
no function
Yes

Check IC1300 Pin17 supply MUST No No

3.3 V ± 5% (Out of supply range may &KHFNRQ5YDOXHLVȍ Change GESTURE_MODULE PC BOAR BOARD
degrade gesture sensitivity)
Yes
Yes

Check FFC connectivity

No
Yes

Change WIRE (FLAT TYPE)

(7 CORE)
[P/N: 1-828-303-21]

Yes
Change GESTURE_MODULE PC
BOAR BOARD

i
m
jo

29
 3CH DAMP Board Mount Diagnosis Flow

30
Playback the music.
SA-WGT4D

The voltage between pin 7 to 8 (+VH) and pin 5 (PGND) of

The audio is outputted No CN1001 on the 3CH DAMP board is +62.5 V. No
from the 3CH DAMP board. The voltage between pin 2 to 3 (íVH) and pin 5 (PGND) of
CN1001 on the 3CH DAMP board is í62.5 V.
Yes
Yes
Reinsert the wire that connected between CN1001 on the
The voltage between pin 6 (+VL) and pin 5 (PGND) of
3CH DAMP board and switching regulator, and check the
CN1001 on the 3CH DAMP board is +17 V. No
voltage again.
The voltage between pin 4 (íVL) and pin 5 (PGND) of
If there is no problem to the wire, check that the switching
CN1001 on the 3CH DAMP board is í17 V.
regulator is properly fixed.
Yes

The voltage between pin 1 (-VG) and pin 5 (PGND) of No

CN1001 on the 3CH DAMP board is -45.5 V.

Yes
jo
Checks OUT terminal REG IC1005 output is -50.5 V No Checks circumference circuit of REG IC1005.
reference to pin 5 (PGND) of CN1001. If there are no problems, exchanges IC1005.

Yes

Checks OUT terminal REG IC1006 output is +7 V reference No Checks circumference circuit of REG IC1006.
to pin 5 (PGND) of CN1001. If there are no problems, exchanges IC1006.

Yes
m
Checks OUT terminal REG IC1007 output is -7 V reference No Checks circumference circuit of REG IC1007.
to pin 5 (PGND) of CN1001. If there are no problems, exchanges IC1007.

Yes
Reinsert the flexible flat cable (FFC4) that connected between
Check the voltage of CN1003 pin 11 (/AMP-RESET) on the
3CH DAMP board is +3.3 V.
No
i
CN1003 on the 3CH DAMP board and CN125 on the
MOTHERBOARD board, and check the voltage again.
If there is no problem to the flexible flat cable (FFC4), check
that the MOTHERBOARD board is properly fixed.
Yes

Yes Assembles into the unit again then, checks whether there is No
End audio ouput from 3CH DAMP Board. Replace 3CH DAMP Board.
 SA-WGT4D
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM - SERVO/USB Section -

CD RF AMP FOCUS/TRACKING ERROR AMP

CD SYSTEM PROCESSOR
DIGITAL SERVO PROCESSOR
SERVICE, OPTICAL DEVICE (7G) IC301

ASDATA0
RF 119 RFIP ASDATA0 115 ASDATA0, MTK-BCK,
MTK-BCK MTK-ALRCK >001B
ABCK 110
VOA/A 125 RF_A MTK-LRCK
ALRCK 114 MAIN SECTION
VOB/B 124 RF_B MTK-MCK
VOD/C 123 RF_C
ACLK 109 MTK-MCK (Page 32)
VOD/D 126 RF_D

VC 5 V20

PD 8 MDI1

AUTOMATIC POWER
FE_LD_CD (780) CONTROL (FOR CD) 9 LDO1
Q402
CN1000
DATA2+
AUTOMATIC POWER TX2P 94 1
FE_LD_DVD (650) CONTROL (FOR DVD) 10 LDO2 DATA2–
TX2N 93 3
Q401 DATA1+
TX1P 91 4
DATA1–
TX1N 90 6
DATA0+
(LO:DVD.HI:CD)MSW 18 MSW TX0P 88 7
DATA0–
TX0N 87 9 HDMI OUT
CD_VR (780) 14 CD_VR CLOCK+
TXCP 85 10 (TV) ARC
DVD_VR (650) 15 DVD_VR CLOCK–
TXCN 84 12 V
SCL (5V)
NC(LIMIT) 107 LIMITSW HDMI_SCL 28 15
SDA (5V)

i
HDMI_SDA 29 16
HOT PLUG DET
GPIO10/HPLG 81 19
+5V POWER
USB SWITCH CONTROLLER +5V 18
IC453 13

m
3 CN1001 14
USB_DP 19 3 1D+ D+ 5 D+
4 XTALO REC/PLAY
X301 2
27MHz USB_DM 20 11 1D- D- 9 D– 5V 1A
3 XTALI
SERIAL FLASH
IC302

SF_DO 25 2 SO/SIO1
SF_DI 26 5 SI/SIO0
SF_CK 27 6 SCLK CEC SWITCH

2D+
Q1000-Q1002,

2D-
SF_CS_ 24 1 CS

S
Q1005
jo 10 4 2

FOCUS/TRACKING COIL DRIVE,

SPINDLE/SLED/LOADING MOTOR DRIVE
IC401

SP+ 11 VOSL+
VINSL+ 4 12 DMO SD-RAM
SP– 12 VOSL–
IC306
SL+ 17 VOLD+
VINLD 23 13 FMO RD0 – RD15 DQ0 – DQ15
SL– 18 VOLD–

TRK+ 16 VOTK– RA0 – RA11 A0 – A11

VINTK 26 16 TRO
TRK– 15 VOTK+
BA0 72 20 BA0
FCS+ 14 VOFC+ BA1 73 21 BA1
VINFC 1 17 FOO
FCS– 13 VOFC– RCLK 60 38 CLK
RWE# 68 16 WE
MUTE 28 108 MUTE
CAS# 69 17 CAS
BIAS 27 6 V14 RAS# 70 18 RAS
DQM0 49 15 LDQM
PRST_
IFSDO
IFSCK

IFBSY
IFCS_
IFSDI

DQM1 59 39 UDQM

35 38 37 34 36 32
‡6LJQDOSDWK
: AUDIO
22 20 17 19 16 14 : DISC PLAY
MTK-BUSY
MTK-RESET
MTK-SDO
MTK-SDI
MTK-CLK
MTK-XIFCS

: VIDEO
MS-476 BOARD
: USB
DM0 150
LOAD+ 10 VOTR+ FWD 6 8 CD-MOTOR+ DP0 151
LOAD– 9 VOTR– REV 7 3 CD-MOTOR- USB-HOST-SEL 27 ‡5FKLVRPLWWHGGXHWR
VDPHDV/FK
CEC-OUT 15
TRAY-IN 12 CDM-LOAD0-SW CEC-IN 10
TRAY-OUT 13 CDM-UNLOAD-SW

SYSTEM CONTROL
IC109 (1/4)

SA-WGT4D
31 31
SA-WGT4D

6-2. BLOCK DIAGRAM - MAIN Section -

AUDIO/PARTY AUDIO/PARTY
L R
CHAIN OUT CHAIN OUT

J602 (2/2)
SIGNAL
SELECTOR
A/D ANALOG IC602 OP AMP
CONVERTER SELECTOR IC601
MIC AMP
IC1101 IC609 Q605, Q607
5 Y1 Y 3 3 + OUT 1
SCKI 6
J1100 14 X1 X 13 5 + OUT 7
MIC1 3 1 5 7 13 VINL BCK 8
LINK SET
14 VINR DOUT 9 Q603
D1100 OP AMP
LRCK 7 IC603
MIC DETECT
J1101 Q1100, Q1101 MUTE
VOUTL 7 3 + OUT 1 1 Y0 A 10 PROTECT
MIC2
Q602
VOUTR 8 5 + OUT 7 12 X0
SCK 16
>001B
MTK-MCK STEREO A/D DATA 2 ANALOG MUTE SW
SERVO/USB SIGNAL SELECTOR CONVERTER
BCK 1 D/A Q606
ASDATA0, MTK-BCK, IC606 SELECTOR
SECTION MTK-ALRCK IC904 LRCK 3 CONVERTER Q612
IC914
(Page 31) 6 SCKI
RXIN6/ALRCK_IO
28, 30, 29

13 VINL STEREO D/A

RXIN5/ABCK_IO
13 BCK OUTL 6 FL
>002B
RXIN7/ADIN0 R-CH 14 VINR CONVERTER
IC604
SW AMP SECTION
MPIO_C2/ALRCK_I1 9 7 LRCK 14 DIN OUTR 7 R-CH (Page 33)
MPIO_C1/ABCK_I1 8 8 BCK

i
15 LRCK
MPIO_C3/ADIN_1 10 9 DOUT
12 SCK

m
MPIO_A1 4
AUDIO/PARTY AUDIO/PARTY
L R
CHAIN IN (TV) CHAIN IN (TV) D/A
CONVERTER OP AMP
IC615 IC915
J602 (1/2)
BCK 19
LRCK 18 1 BCK VOUTL 7 3 1+IN
14 MPIO_B3/ADIN_2 DOUT 17
1OUT 1
FM DRIVER 3 LRCK
13 MPIO_B2/ALRCK_I2
(FM RECEIVER)
ERROR/INT0

IC902 16 SCK
NPCM/INT1

2 DATA
CN900 IISD 14
ANTENNA 1 2
FM
2 1 FRF1 LRCK/LOUT 13

BCLK/ROUT 12 R-CH
jo 42 41 28 26 24 52 91
X103
12.288MHz

92 70
X105
14.5MHz

71 140
X104
48MHz

139 32 47 33 40 30 29 43 54
DIR-INT0
DIR-INT1

SSI3-DI
SSI3_LRCKO
SSI3_BCKO

AUDIO-X1

AUDIO-X2

EXTAL

XTAL

USB-X2

USB-X1

SSI0_DO(PARTY CHAIN)
LINK-DET
SSI0_DIC(MIC)
SSI2-DO(FR)
SSI0_LRCKO
SSI0_BCKO
AUDIO-CLK-OUT

SSI1_DO(SW)
MIC-DETECT

/LINE-MUTE 48

LINK-SET 115
SYSTEM CONTROL
BT-RESET/SD_CD_0

16 X1 DA 11 128 ST-DATA IC109 (2/4)

BT-RXD(MD-CLK)

X900

4)ODVK6,2
4)ODVK6,2
4)ODVK6,2

4)ODVK6,2
12MHz CK 8

4)ODVK&/.

DIR-CP-SDA
127 ST-CLK

DIR-CP-SCL
4)ODVK&6
17 X2
‡6LJQDOSDWK
BT-TXD

IIC/RDSI 6 45 ST-RDS
BT-ON

: AUDIO
65 133 113 114 169 172 166 170 168 167 126 125 : TUNER (FM)
BUS BUFFER : CD PLAY
IC102 (1/2)
: MIC
BLUETOOTH MODULE 1 2 3 5 6 7 2 6
5 6 : BLUETOOTH
CS
SO/SIO1
W P/SIO2
SI/SIO0
SCLK
HOLD/SIO3

SDA

SCL
BT-RXD ‡5FKLVRPLWWHGGXHWR
BT-TXD VDPHDV/FK
BT-RESET
BLUETOOTH EEPROM EEPROM
3.3V POWER CONTROL IC106 IC105
Q103, Q104

SA-WGT4D
32 32
 SA-WGT4D
Ver. 1.2

6-3. BLOCK DIAGRAM - AMP Section -

AUDIO CODEC DIGITAL POWER AMP

IC1009 IC1010

BOOSTER FL
>002B SW
VOUTL2 22 2 IN-2 LO2 25
Q1011 + + L
7 VINL1 WHITE
MAIN
FL VOUTR2 21 9 IN-1 –
SECTION 9 VINL2 HO2 28
BOOSTER TB1001
Q1010 SPEAKERS
(Page 32) R-CH
10 VINR2 TH1001 ONLY FOR SS-GT4DB
VS2 27

23 OTP
–
R
BOOSTER FR
VOUTL1 26 LO1 18
Q1007 + + RED

BOOSTER DC DETECT
HO1 15
Q1006 Q1009

VS1 16

CSD
CLK
32 11

INVERTER
Q1008
DA
CL

18 19

i
DIGITAL POWER AMP

m
IC1008

9 IN-1

TH1002

23 OTP
BOOSTER SW+
LO1 18
Q1001 + SP1
(SUBWOOFER)

BOOSTER DC DETECT
HO1 15
jo CLK

32
VS1 16

CSD
11

INVERTER
Q1002
Q1000 Q1003

D1030

FAN MOTOR
CONTROL
Q1021
FAN MOTOR
DRIVE
Q1022, Q1025
DC FAN

FAN PROTECTION
INVERTER
Q1024
Q1018

BUFFER
Q1019

56 57 96 78 53 82
AMP-PROTECT

/AMP-RESET

FAN_DET
EVOL-DATA/DAMP_PDN
EVOL-CLK/DAMP_MUTE

AMP-CLK/SD_PCON

‡6LJQDOSDWK
: AUDIO
SYSTEM CONTROL
IC109 (3/4)
‡5FKLVRPLWWHGGXHWR
VDPHDV/FK

SA-WGT4D
33 33
SA-WGT4D

6-4. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section -

LIQUID CRYSTAL
DISPLAY DRIVER SPM-C-MON 79
LIQUID CRYSTAL IC1000
DISPLAY
ND1000 BUS BUFFER
INHB 13 175 LCD INHB PROTECTION CONTROL
IC1004 PCONT-DAMP 118
Q576
VOLTAGE REGULATOR
33 SEG0 IC009

14 - 47
I BUS BUFFER POWER CONTROL
SEG32 SDA 10 4 LCD_SDA PCONT-BTSTBY 122 PROTECTION
IC1002 PROTECTION CONTROL
Q009 +1.2V 3 SW1 VIN1 1
Q575

51 - 52, 1 - 2
4 COM0 +3.3V
BUS BUFFER POWER CONTROL
I SCL 9 2 LCD-CLK
COM3 IC1001 D+3.3V PROTECTION 14 SW2 VIN2 16
Q008 PROTECTION CONTROL
BUS BUFFER Q574
CSB 8 176 LCD_CSB
IC1003
VOLTAGE
RES 76 4 DETECTOR 2
REMOTE CONTROL IC103 PROTECTION CONTROL
RECEIVER 135 SIRCS Q572
IC1100
EN1000
MIC LEVEL REGULATOR, SWITCHING
83 MASTER-VOLUME/MIC-VOLUME
PROTECTION CONTROL (SSN-161AD) BOARD
C-CONT 55
Q571

S1007 ~ S1008 85 AD-KEY1 POWER CONTROL

+1.2V REG.
+1.2V 1 6 PROTECTION
IC303
Q005
LOW AC DETECT SWITCH
S1001 ~ S1006, S1009 LOW-AC-DET 94 LOW_AC
84 AD-KEY0 Q108
S1400 ~ S1406 AC-CUT(MD-BOOT0) 63

POWER CONTROL POWER CONTROL BUS BUFFER AC CUT SWITCH

11 12 AC DET

i
S1000 6 POWER-KEY MTK-POWER-CTRL 59 PROTECTION PROTECTION IC102 (2/2) Q107, Q109
Q457 Q006
MAIN-ON
LED DRIVER +3.3V REG. 1 +VH +VH
+3.3V 3 POWER CONTROL

m
IC1250 IC305
4 PROTECTION +5.2V REG.
BAR_RGB_B_BOARD (RIGHT) NFC MODULE Q007
/OUT3 IC001
(RC-S730 (WW)) SYSTEM CONTROL
8 - 13

BLUE I IC109 (4/4) +7V REG.

D1650 /OUT8 POWER CONTROL +7V +VL
RED 14 SW2 IC1006
DATA 132 NFC_SDA +5.2V PROTECTION
GREEN TO
Q459
SCL 131 NFC_SCL AMP
BAR_RGB_A_BOARD (LEFT) SECTION
IRQ 124 NFC-INT USB+5V 3 SW1 VIN1 1
BLUE RF-DET 137 NFC-RF-DET -7V REG.
VIN2 16 -7V -VL
D1600 USB COMPARATOR IC1007
RED USB_OC/SD_LED0 35 7 6
IC452
GREEN
BAR_RGB_B_BOARD (RIGHT) 12 EN2
-VH -VH
/OUT9
14 - 19

BLUE I VBUS-OE/SD_WP_0 112 5 EN1

D1650 RED /OUT14
SIN 2
GREEN PROTECTION PROTECTION PROTECTION -12V REG.
BAR_RGB_A_BOARD (LEFT)

D1600
BLUE
RED
GREEN

D1012

SW_RGB_LED_L BOARD,
20 /OUT15
SCK
TRANS
PWMCLK
3
4
21
jo /SD-FAST 49

+3.3V

+3.3V
3

3
+3.3V REG.
IC008

+3.3V REG.
IC903
4

4
+5V REG.
IC006
+9V REG.
IC004
POWER CONTROL
PROTECTION
Q004
SWITCH
Q1016

+7V
SWITCH
Q1014
SWITCH
Q1015
IC1005
-VG

+13.5V

SW_RGB_LED_R BOARD +9V

BLUE 5 OUT0
D1700,
RED 6 OUT1 POWER CONTROL POWER CONTROL
D1750 +5V +5V REG.
Q302, Q303 4 5 PROTECTION
GREEN 7 OUT2 IC1000
Q461
1
LED DRIVER
IC1400 5V_HDMI 1

SIN 2 117 RGB-SOUT PCONT-PSAVE-PROTECT 57

/OUT0
5 - 20

D1401 ~ D1408 I SPM-AMBIENT-TEMP 80

/OUT15 TH571
SCK 3 134 RGB-SCLK PROTECTION POWER CONTROL
SWITCH PROTECTION
PWMCLK 21 136 RGB-PWM-CLK GESTURE CONTROLLER Q1012 Q011
IC1300

TRANS 4 173 RGB-TRANS-LED +13V

3D-DETECT 120 1 EIO0 TXD 15 TRANSMITTER (AC IN)

3D-RESET/SD_D1_0 111 13 /MCLR RX0 21 NORTH ELECTRODE

LED
D1004 DRIVER 51 LED-CTRL 3D-PWM-SDA 130 9 EI04/SI0 RX2 23 EAST ELECTRODE GESTURE CONTROLLER
Q110 SOUTH ELECTRODE
3D-PWM-SCL 129 10 EI05/ST1 RX3 24
LED RX4 25 WEST ELECTRODE
D1001 DRIVER 175 LCD-BCKLED/INHB
Q1000

SA-WGT4D
34 34
 SA-WGT4D
Ver. 1.2

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards. For Schematic Diagrams. RGB_SPLITTER board
Note: Note:
• X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
3CH DAMP board
• Y : Parts extracted from the conductor side. 50 V or less are not indicated except for electrolytics and
• f : Internal component. tantalums. PANEL board
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise GESTURE_MODULE
(The other layers’ patterns are not indicated.) specified. PC BOAR board
• f : Internal component.
Caution: • 2 : Nonflammable resistor.
Pattern face side: Parts on the pattern face side seen GESTURE_RGB board
• C : Panel designation.
(Conductor Side) from the pattern face are indicated.
Parts face side: Parts on the parts face side seen from Note: The components identified by mark 0 or dotted
(Component Side) the parts face are indicated. line with mark 0 are critical for safety. MOTHERBOARD board
Replace only with part number specified.
• MOTHERBOARD board is multi-layer printed board. MIC_IR board
However, the patterns of intermediate layers have not • A : B+ Line.
been included in diagrams. • B : B– Line.
• Voltages and waveforms are dc with respect to ground
• Indication of transistor. RC-S730 (WW)
under no-signal (detuned) conditions. MS-476 board
no mark : TUNER (FM)
C
( ): CD PLAY
Q These are omitted. { }: DVD PLAY
[ ] : USB BLUETOOTH module REGULATOR, SWITCHING
B E (SSN-161AD)
* : Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production

i
• Abbreviation
tolerances.
AR : Argentina model SW_RGB_L board
• Waveforms are taken with a oscilloscope.
AUS : Australian model
Voltage variations may be noted due to normal production
E4 : African model

m
tolerances.
E12 : 220 – 240 V AC area in E model
• Circled numbers refer to waveforms.
EA : Saudi Arabia model
• Signal path.
LA9 : Latin-American model
F : AUDIO
MY : Malaysia model
f : TUNER
RU : Russian model
J : DISC PLAY SW_RGB_R board
Note 1: When the complete MOTHERBOARD board L : AUDIO/PARTY CHAIN IN
is replaced, refer to “NOTE OF REPLACING E : VIDEO
THE COMPLETE MOTHERBOARD BOARD, d : USB
BLUETOOTH MODULE AND RC-S730 (WW)” on G : Bluetooth
page 6. N : MIC
• Abbreviation
AR : Argentina model
Note 2: When the MS-476 board is defective, exchange
the entire LOADING COMPLETE ASSY (T).
jo AUS : Australian model
E4
E12
EA
LA9
MY
RU
: African model
: 220 – 240 V AC area in E model
: Saudi Arabia model
: Latin-American model
: Malaysia model
: Russian model

SA-WGT4D
35 35
SA-WGT4D
Ver. 1.2

6-5. PRINTED WIRING BOARD - MOTHERBOARD Board (Component Side) - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

MOTHERBOARD BOARD
A (COMPONENT SIDE)
ÚEA, AR, E4, E12, LA9 J602
L R

AUDIO/PARTY CHAIN AUDIO/PARTY CHAIN

IN (TV) IN (TV)

AUDIO/PARTY CHAIN AUDIO/PARTY CHAIN J907

OUT OUT VIDEO OUT FOR
SERVICE
CN1000 ONLY

B (CHASSIS)
HDMI OUT
(TV) ARC
V
(CHASSIS)

8 7
Q457, Q602
21 22
CN101
C1 B2 E2 6 1
JL635

C680
1

C681
E1 B1 C2 20 19 23

C980
JL901
JL900
R1012 R126 R124
JL905
JL1000 JL1001

C682
JL1002 JL631
JL605 R687

C642

C1014
R661
JL604 R1010 R1011 JL1003

R691
Z001 R690 JL1005 CL328 CL329

RB303
JL620 R1014 R1015 Z903

C648 C640
R653 JL619
JL1006

C644
IC606
R756
R641
JL904

RB305

RB302
JL110
R627 R311

R674

C364
R628

27
C649 C653

28
Q602

R309
CL380

R688
JL111

RB301 RB304
CL300
C655 R368
CL309

C963
R625
R624

R367
97 96 65 R380

C359
C360 R382
JL601 64
R390
R036

JL330
D CL310

RB306
R365 R379
JL602 C341 129
CL316 R360

RB307

C365
CL315
IC301
R955

R358

IC306
C952 C951 R369 JL056

C337
JL352 128
C954

R623

C363
C334

C076
33

>003P
R349
JL353 R371 1 32
C981

i
X602 R958
C963

R351

54
C985
JL348

1
JL057 R633 R953

RB308
IC305
R334 R340

R342

R344 RB309
R388 R332 R336 C362
C958
PANEL BOARD
48 37

FB320
1 C353 R338 JL350
R989

36 X301 R415 SL403 R402

R327

R355
R981

JL331
C411 C402
IC904 C356 CL338 SL402
CN1000

R331

FB321
R988 JL349
R982 C322 C323 CL308 SL401 R418 C403
SL404 R401
IC302

R345
R983 C413
(Page 39)
12 25

R408
13 24 R987 R354

IC453
R984 JL404
R305
CL335 FL301
E

m
R959

R472
R470
R985
R307

C412

C401
JL341

C324
SL301

R986
R952

R329
R957

R301
R389

C468
JL347 JL305
R480

R404
R951
R950

C408
C606

C467
JL346 JL313 JL317 JL318

1
SL405
JL309
CONNECT TO

2
SL408
JL322

R409
FB455

1
JL311 JL319 JL462 JL402 MS-476 BOARD

SL407

CN303
4
JL303 JL461 JL463

CN451
JL315

5
SL406
JL307 JL321
Z904 C073 JL323 JL455 C419 R410 JL403
C601
C612

JL401 JL405
1 23 1 23 JL406
CN302 CN302 C418

4
2 24 JL301 2 24 JL460
R048

JL302 JL454
JL603 C071 JL324
JL306

6
Z451
JL032 C366 JL310 JL314 JL320
6 1 6 1
Q007 JL329 CN401 CN401
E
JL308 JL312 D402
JL304

C405 C406
8 7 8 7

F R039
R323

JL316
R040

D401
C367

R1006
R316 JL906
1
Q006

C311

2
E

SERVICE, OPTICAL
R386

R1003
JL050
DEVICE (7G) JL613
CN303
4

C1000
R1004
5

K
C066 JL055
D1001
C420

C423

Q1001
JL328 JL326 Q1005 E E
A

JL022 SERVICE, OPTICAL

C064
R1005 R030 DEVICE (7G)
R1002
C1001
C609

JL023
6

JL325

R028
Q457
E
R1001
Q1002
E
4

E
R1007

Q1000
R716
R711

JL327 Q459
CN601

JL615
>001P JL292
JL189 R034

Q005
JL163
R299

R274 R221

JL614
R181

R164 JL190

E
JL612
R595

JL021
C622

C067
R197JL210 JL059 JL024
R230 R582

R037
1

C502

R168JL297
R219
R295

R211

MIC_IR BOARD
R254
R257
R218

R261
R213

R645
5

C065
C139
R224
R229
R215

R171

G JL129

CN1100
Z901 JL616
jo JL281 JL282 R150 JL183
R193 R201

R232

R594 JL182 JL209

C088
E

R272
C691
C671

JL179 JL193 JL212 JL130

R596

JL185
1
R226

(Page 44)
JL211
Q606

R681 JL222
>004P
2

JL293 JL187 JL298 JL294 Z101 JL296

C695

JL278 JL295
R170 R255 JL137 JL133
JL164 R103 JL162 44 1 R271 C087
R533 R169 45

PANEL BOARD
JL161 JL136
C672

R173 176 R111 JL139 JL138

IC109
R718

R234
C986

JL288 R293
JL269 R172 R110
R576

R292 JL140
CN1007
R151

R116 R291 JL107 JL141

JL285 JL142
C106 JL143
(Page 39)
R125 C109 R575
CN122

R123 R208 JL108

R132

JL144
R760

C102
R762

JL268 JL145
R137

R102 JL300 JL146

C126
R761

JL147
R188

X105
R186

Ú R285 JL230
C922

C298
C297
C689

JL287
H
R176

20 11
JL155
C998

IC914
R127

C127

R829 JL160 JL159 JL231

C151
22
C699

1 10 JL232 JL505 NFC MODULE

C696

23

C152
R267
C994

FB117

JL150
X104

(RC-S730 (WW))
R275

R153JL158 R276
R154 R278
C997 R155JL255 JL214 JL219
R156JL165
R117

TH571

Ú JL067
R010
R909

R011

JL218
R115
C692

R177 88 133 JL151 L007

C968
R976
C972

Z604
C029
R209

89 132 JL213
R796
R826

R793 R178
C047

R179JL167 JL256 R174R280 R531 JL153 JL289

E R200 JL184 JL186 JL166 JL276
R797

R795
C991

R298

Q108 JL168 R196 X103 R189 R032

R227

E JL072 6 2
R228

Q107
JL275 JL154
C049

C744 R180
C038
IC915

6 2 R026
JL191

JL272
JL207

JL208

C110 JL283
JL172 R212

5 1
JL152
C738

JL273

C019 C028
JL188

C041
C104

R104
IC615
JL274
JL271

C299 5 1 CN105
C992

R160 Z102 CN105

R198

R592
Q109 E

JL116 R182
R994

JL195
R128 IC009
R591
R241
R225

R238
R256

C989 R972 C130 C132

R233

A K 7 1 7 1
R995

R819
C014
C107

CN120 CN120
R214
R217
R100
R220

C006
C004

R977 JL148 R203 R106

D102 JL178 JL227
C105

>005P
R975 6 2 6 2
JL203 JL134
I C990 R973 C993 JL135 C167 JL105 R013 R088
L004

C103 JL132 JL069 R014

C969 JL197
R518

R519

JL173
JL171
JL175

R009 C050

L002
IC103
JL170

JL169
R008

JL241 JL202 JL204 JL106

C016

JL131
GESTURE_MODULE
2

JL502 Z902
1

JL004 JL176
JL242 JL506 JL112
CN102

PC BOAR BOARD
JL501 JL174 JL201
JL199

JL071
10

JL215 JL216 JL235 JL113

C054 R003

JL198 JL196 L001 DC01

C003 R002

C726 C577 JL114 JL109

CN1300
C015

JL617 JL044 R063 JL200

JL618 JL005
C083

Z603
JL206 JL205
(Page 42)
JL217 L003
R517

JL007 R012
C059

E
19

C013

R087
C005
18

JL049 Q009
R516

JL048
R001

C017

JL194
E

IC001
2

JL251
C030
R061

JL006
R062
R578

Q008

JL503 C093 BLUETOOTH MODULE

C026
C057

C084

JL244 R086
R525

J
CN102
C024

JL248
>002P
9
C052

JL249
10

JL068
C039
C037

JL247
R515

R025
CN125

JL504 L008
C092
JL270 C010
R007

R006

R023

JL047
3CH DAMP BOARD
JL045
C053

C011
JL008 C091 L006 Z602
JL070
CN1003
10 11
JL053
2

C055 R024
1

(Page 38) 1
CN001
9
JL054

11
K Note 1: When the MS-476 board is defective, replace the
1-980-441- (11) LOADING COMPLETE ASSY (T).
CONNECT TO
REGULATOR, SWITCHING ~ AC IN
(SSN-161AD)
BOARD Note 2: When the complete MOTHERBOARD board is
replaced, refer to “NOTE OF REPLACING THE
COMPLETE MOTHERBOARD BOARD, BLUETOOTH
MODULE AND RC-S730 (WW)” on page 6.

SA-WGT4D
36 36
 SA-WGT4D
Ver. 1.2

6-6. PRINTED WIRING BOARD - MOTHERBOARD Board (Conductor Side) - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

A
MOTHERBOARD BOARD
(CONDUCTOR SIDE)
ANTENNA
FM

B
4 3
Q603, Q605, JL907
Q607
CN900
2 1
C1 B2 E2
Z610
Z909

C1013
E1 B1 C2

D900

L900
R937
R1019
C636
L601

L902
K A/K A
C1006 R1026

C930
R1000
C638

R938
R1017 R1020
L901

C1005
C

L605
C1003

C932
R939 C931

C933
IC1000

C935
R940 5 1

R657
Z104 C1004

R677 R660

C941 C934
6

R312
20

R944
R912 R911 21

C938
C936
10 16

C664 C631 C602 11 15

C937
R914

C647 C657 R913

X900
IC902 R943

Q302

C626
R359

C650 C652

FB610 C943
R319

R685
CL301

R686

R947
R946
C343

C627
C645
C646
Q303 C376

R945
R362
R321
E

R353
E

R671

R662

R752
R753

IC903
C306
CL395 CL307

C347

C352
R751
R669 R663
R381

C351

R857
C643 C641

R370
C348 C665 R750
C999 C660

R651 R650
C346 CL302 C711

C628
R689
C357

C344 CL311

C620
D

C621
C340

C350
CL381
C342

Z906

Q605
C917 Q603

C339
CL313

R692
C325

R700
C358

R330
R357

C338
C330
C326

R328
C331

Z611 Q607

R997
R438

C629
C328
R434
R435

R348
R378
R439

R322
C319 C316
R356
IC303

i
R326
R303

C373
C979
L301

C336 R339
R347
R302
C407

R411 R664
C375

CL401 C372 C960

C315
1 28 C321
IC401

R352

CL402 CL403 C369 R350 C950

CL408 CL412 CL337
CL404 JL355
R387
R343

R406 CL409 R346 R642 R915 R606

FL601
7 22 CL321 C949 R644
R314
C409

m
R621

IC601
R407 CL405 CL411

C766

R916
R313 CL322

R649
29 30
CL407

R604 IC602 R616

R600
CL410
C404

8 21 CL406

C767
R451 C462 C605 Z914
R465 R607
C465 R615
14 15 R634 R608
C463 R646
C616 C607
R318

R478 C302 R612

R464
R310

R613 R648
C303

R605
R636
R498
R453

R452
IC452 Q612 R602 R647 R639
R433
R051
R052

C421

Z905
Q402

Q401

E R610 R635
C466

Z502
C074
C075

C424

F R424
R054

R626
R429
R420 CL415 CL414

C618
C614
E

CL413 Z908
R422

R622
R431
R432

C615
R421

R609 C610

R640 C625
R426
R425
R423
R053

C613
R430
R428
R427

R638
C634
C608
R619

R654
R617
R1030

R652
R618

C604 C635
R820 R614 C603 C633 R655
R620

IC603 R656
R632
C632 C619
C617 R643 C630 C624
R631
R630
R629
R579

IC604
R580

G
jo
R237

R112
R239 R289 R294
R251

C501

C168 R290 R286

R590

C673

R288 R287
R242 C679
R270 C669 R709
C133
C143
R119

R587
C142
C141

C678
R273

R205
C135

C503
C674

R247 C667
R300
C153

R284 R720 C666

C111 R708
C140
C137
C148

R129

R723 C670
R120
R589
IC106

R222 R133
IC102

C146
R134

R719
R107 R131
IC609

R722
R598

R139

R143
R135

C154 C112 R817 Z907

C164 C155 C114
R140

C156
C115

R597
C157
R978

C995

Z103
C158 C118
H R175
Q110

C116
E

C117
R192 C160

C159 R149
C280 C120
R283

R593

C996
R253

C138
C144

C282 C281
R250
R252 R167

C136

C123 C121
R202 C134

FB101 C122
R166
R223 R532

C147 R194 R577

R114

R204

C128
R246
R105
R248
R113

R152
R244

R236 R195

C131
C161

R190

C129 R146
C742

R574
C749

R297 R145
R206

C162 R245 R243 R144

C149

R122

R157
R159

C165
R161 R191 R158
C166
C964
C748
C150

IC105
I
C040

Q572
E C574
R1028

R483
R491
D572
A

E
R485

E
D571
A
Q571

Q574

Q103
E

Q575 Q576 C101

C100
C573

Z501 E R571
IC008

Q104 E
R487
E

R572
R794

R108 Q461 R520

R109
R035

E
E Q012 R521
C068

R029
R065
IC004 IC006
C072

Q004 E
Q011
R064

C085

C062
R017

C051

J
E

Z915

R020
R792

R019
R022
R080

11
1-980-441- (11)
K

Note: When the complete MOTHERBOARD board is replaced,

refer to “NOTE OF REPLACING THE COMPLETE
MOTHERBOARD BOARD, BLUETOOTH MODULE AND
RC-S730 (WW)” on page 6.

SA-WGT4D
37 37
SA-WGT4D
Ver. 1.2

6-7. PRINTED WIRING BOARD - 3CH DAMP Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

3CH DAMP BOARD 3CH DAMP BOARD

A (COMPONENT SIDE) TB1001
(CONDUCTOR SIDE)
¾AEP, UK, RU, MY, AUS ¾AEP, UK, RU, MY, AUS
SPEAKERS
ONLY FOR SS-GT4DB

L R
WHITE RED

CONNECT TO
REGULATOR, SWITCHING + – + –
(SSN-161AD)
BOARD

B
Q1002, Q1003,

C1122

C1123
Q1008, Q1009,
Q1016, Q1018,
Q1019, Q1021
CL1054

R1022
R1024
C1 B2 E2 CL1066 CL1065

Q1003
2

Q1009
CL1057 ¾

CN1005
K
C1076
CL1053

C1121

C1194

C1116
A A

C1017
E1 B1 C2
D1030

C1120
CL1067

1
R1100 CL1058
CL1059

R1098
C R1194

R1103 ¾
CL1021

R1195 C1119 CL1022

C1128 CL1029
C1118
8

C1129

CL1068

C1238
CL1025 CL1026

D CONNECT TO
CN1001

REGULATOR, SWITCHING
(SSN-161AD) R1090 R1093 R1124 R1127 R1014
BOARD

C1107
C1239
C1074 C1073 C1014 C1015 CL1069

C1106
i
CL1028

C1009
1

CL1027
E

m
C1068

C1102

Q1015
R1153
E
D1021 L1000 L1007 L1005
R1152 R1151
K A

C1139
C1138

C1137 CL1063

IC1005

G
jo C1060

¾
CL1015

C1065
CL1012
C1064

C1071
¾ ¾
C1098

C1105
CL1020

CL1017
C1094

C1099
¾
C1001
CL1003

CL1000
C1005
Q1001

Q1000

Q1010

Q1007

Q1006
Q1011

¾
R1084 ¾ CL1024
R1120
CL1004

H CL1016 CL1023
CL1013 CL1018 CL1001
R1131

D1020 Q1019
C1147 R1168
R1121

R1165
A
D1024

K A TH1001
R1197

CL1019
K

CL1014 CL1002
R1096

TH1002
R1006

R1117
R1086

R1082
R1010

R1040 R1041

R1119
A

Q1016 Q1014

R1164

R1087 C1241
C1205
R1266

C1206

R1169
R1132
R1130

R1118
E

R1042

R1116
K
K
D1023

C1204 R1009
R1265
R1004

R1020 C1203 R1001 D1017

A

R1011 D1014
D1022
K

A K K A A K

R1142

R1065

R1066
R1080
D1018 R1138
A

R1039 R1133 C1146 R1085

R1076
R1077

C1240
A

C1013 D1004 C1072 R1115

D1001

R1140
R1139

R1144
R1000
C1200

R1143
R1141
K
Q1018

D1010
C1034

C1109

C1093

R1158 26 17 26 17
D1019

A
D1011
C1201

R1028
IC1008

27 16 27 16

R1033
IC1010
R1134
R1135
R1038

D1000

R1104

R1201
R1136
A

33 R1003 33
C1199

R1081

I DC FAN
K

K
R1137

R1114

R1099
R1109
A K
R1005

3
C1144
C1186

R1199

R1198
A
C1033

R1021

A
32 32

D1033
11 11 CL1031
Q1002

R1079

R1206 C1185
Q1024

D1032
C1161
R1112 C1091

CN1004
C1081
C1080

E
C1090

1 10 1 10 CL1044
1

C1032 C1030
R1037
R1007

K
R1207 C1018
C1089

K
CL1039
C1079
C1031
C1164

R1246
R1167
R1173

C1019 R1247
R1170 R1172

C1162 C1078 C1077 R1221

R1036
R1105

R1102

R1101

R1180 CL1036
4

CL1042
C1152 C1151 D1025
R1171

R1222
C1028

R1181
R1251
R1252
IC1006

K A
C1086 C1087

C1157
C1148
C1027

C1155 40 21 R1097
Q1021 R1189

R1284
K

Q1022
R1107

CL1030
D1034

IC1009 B E R1275 CL1062

R1215

E
R1106

Q1008

R1283
R1031

C1092
R1214

R1188
R1030

Q1025
C1166

C1220

R1187
C1221

1 20 R1182 R1190
R1083

C1142

C1143
R1113 C1242 CL1037 CL1061
C1187 CL1043
R1156 C1244 C1243
2 18
CL1045 CL1038 CL1047
R1157 CN1003 C1156
CL1050
C1245
IC1007

C1188 R1279 1 19
C1165

C1158
CL1041 CL1049
C1246

R1280
R1282
C1247

¾ CL1046
C1248
¾
¾ CL1048
R1281

12 12
K (12)
1-980-515- (12) 1-980-515-
>002P
MOTHERBOARD BOARD
CN125
(Page 36)

SA-WGT4D
38 38
 SA-WGT4D

6-8. PRINTED WIRING BOARD - PANEL Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

A
PANEL BOARD RGB_SPLITTER BOARD
CN1250
(Page 46)
>006P

B
LP1003

LP1001

CL1093 CL1122

CL1036
CL1041
CL1045

CL1091

CL1087

CL1071
CL1089

CL1052

CL1050

CL1039

CL1037
CL1085

CL1075

CL1068

CL1058

CL1043
CL1048
CL1054

CL1051
CL1088

CL1053
CL1055
CL1059

CL1038
CL1049
CL1090

CL1082

CL1044

CL1042

CL1040
CL1086

CL1077

CL1073
CL1080
CL1092

CL1069
CL1056
CL1046 CL1119 R1038
S1016 CL1111 S1015
40 39 CL1121

13
CL1047

D1011

12
SOUND PARTY
S1006 S1019 CL1120 FIELD LIGHT
MIC VOCAL
52
1 IC1000 27
26
ND1000
LIQUID CRYSTAL DISPLAY
D ECHO FADER E Q1000 JR3028
CL1066 CL1110

CN1006
CL1095 CL1057 JR

R1015
R1023

1314
C1020 CL1072
R1022

JR

R1016
R1014
JR3005

2
JR3074 C1019

1
CL1076 JR

JR3030
JR3021
JR
CL1026 CL1079 CL1083 JR3059 CL1061

JR3034
JR3003 JR3046 JR3099 CL1070

JR

JR
CL1094 CL1074

JR3023

R1021
R1017

i JR
JR JR JR
R1019

JR3026
C1022

JR
C1025

R1040

CL1019 JR3082 JR3085 JR3077 CL1060

JR3007

JR
CL1021 R1018 C1021 CL1067 CL1064
JR3088

JR
JR JR JR
JR3092

CL1023 CL1081
JR3080

EN1000 C1023
JR

CL1062
C1035 JR

JR

R1020 CL1065

JR3008

R1037
MIC LEVEL
JR JR3052
JR3019

JR3056

JR3066
JR3020
JR3097

JR
C1034

JR3013

R1036

JR

JR
JR
JR
JR JR JR3057

JR3010
CL1084
JR

S1014

JR3094
JR
R1056

JR JR3009 S1013

JR
JR3093
E CL1034

m
JR3045

JR3002

JR3049 PARTY

JR3047
JR
JR3039 FOOTBALL

JR
JR
JR

JR

JR3067 CHAIN

JR
CL1124 R1009 JR JR3024
CL1113

JR3075
CL1031

JR3076
JR JR3018 JR

JR3035
CL1029 JR3078 JR
CL1109

JR

JR
CL1108
JR3014

JR3369
JR3022

JR
JR
CL1035
1

JR

CL1016 JR JR3012
C1009
C1012

JR3061 CL1100
R1028
JR

2 10
2

JR3096

JR3036

JR3001
CL1033 JR
CN1004 REC/PLAY

CL1028
JR3033

JR

JR 11

JR
1
JR3032
JR3070 R1060

JR3073

JR3027
CL1018 CL1101
JR

W1001 CL1063
JR

JR

JR3016

JR3025

JR
JR
CL1020 CL1017 D1004
5V 1A

R1029
JR
JR3098 JR3011 S1018
IC1004
JR3060

CL1013
IC1001
JR3041

CL1022 JR
FIESTA JR JR3037

JR3029
CL1014

JR

>004P
JR
JR

JR

JR
IC1003

R1035
CL1025 JR
R1041

R1043

R1005

S1017
CN1007

JR3090 R1042

CL1114 JR3058
JR3063

CL1006 CL1027 JR3038

MOTHERBOARD MEGA
JR

JR

JR CL1030
JR3000

BASS S1012 W1003 CL1004

JR3081

JR3084

IC1002
JR3071

JR3017
JR3072

6
R1052
F BOARD
JR

JR

JR
CL1009

REC TO USB
JR
JR

CL1024 JR
CL1008

JR3086

JR
CN1001
22

JR3015 CL1032
JR

CN122
5 7

R1034
23

CL1125
>007P
JR
JR3004 CL1107 1 4
JR3083
JR3079

JR3091

R1013
(Page 36)
JR3095

JR

JR

JR

S1011
JR

CL1007 CL1000 CL1002

GESTURE_RGB BOARD

5
ENTER

JR3051
CL1001

CN1000
CL1005 C1001
>003P
JR3378

JR
JR3068
JR3069

CN1400 CL1106

3
JR

JR

JR

CL1011
(Page 43) CL1003

C1004

C1003
MOTHERBOARD

1
JR JR3006

BOARD
JR3087 JR
S1009
G S1005
+
jo – PAIRING
BLUETOOTH
S1010
FUNCTION
CN451
(Page 36)

R1032
S1004
R1039

D1012
–

R1033
JR3040 JR3042
R1027 JR JR
CL1105
CL1112 CL1099
CL1104 JR JR
JR3044 JR3043

R1031
R1026

CL1103

JR3062
CL1102 JR
CL1097 R1025 CL1098
R1024

JR3065
JR3053 JR3055

JR3089

JR
JR JR

JR
R1030
S1002 S1003 S1008 S1007

I TUNING + TUNING – N x

JR3064
> .

JR
JR3048
R1055 CL1118

JR

9
CL1117

CN1003
CL1116

CL1123
CL1115
>008P
MIC_IR BOARD

3
CL1012

J CN1101

1
(Page 44)

CL1096

S1001 S1000
Z 1

LP1000
11
K
1-980-560- (11)

SA-WGT4D
39 39
SA-WGT4D

6-9. SCHEMATIC DIAGRAM - PANEL Board (1/2) - • See page 49 for IC Block Diagrams.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

A PANEL BOARD (1/2) ND1000

LIQUID CRYSTAL DISPLAY

CL1036
CL1037
CL1038
CL1039
CL1040
CL1041
CL1042
CL1043
CL1044
CL1048
CL1049
CL1050
CL1051
CL1052
CL1053
CL1054
CL1055
CL1058
CL1059
CL1068
CL1069
CL1071
CL1073
CL1075
CL1077
CL1080
CL1082
CL1085
CL1086
CL1087
CL1088
CL1089
CL1090
CL1091
CL1092
CL1093
CL1122
SEG01
SEG02
SEG03
SEG04
SEG05
SEG06
SEG07
SEG08
SEG09
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
COM0
COM1
COM2
COM3
SEG0
C

SEG23
SEG22

SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15

SEG14
SEG13

SEG12
CL1056

CL1121
2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6
39 38 37 36 35 34 33 32 31 30 29 28 27

SEG23
SEG22
NC_37
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
NC_29
SEG14
SEG13
D SEG24 40 26 2.6
SEG24 SEG12
SEG25 2.6 41 25 2.6 SEG11
SEG25 SEG11
SEG26 2.6 42 24 2.6 SEG10
SEG26 SEG10

i
SEG27 2.6 43 23 2.6 SEG09
SEG27 SEG9
SEG28 2.6 44 22 2.6 SEG08
SEG28 SEG8
SEG29 2.6 45 IC1000 21 2.6 SEG07
SEG29 BU9795AKS2 SEG7
SEG30 2.6 46 20 2.6 SEG06
SEG31 47
SEG30 IC1000 SEG6
19 2.6 SEG05 5.2 0 5.2 0 5.2 5.2 5.2 5.2
E 2.6

m
SEG31 LIQUID CRYSTAL DISPLAY SEG5
SEG32 CL1045 2.6 48 18 2.6 SEG04
SEG32 DRIVER SEG4

VCC

OUT_Y

VCC

OUT_Y

VCC

OUT_Y
VCC

OUT_Y
2.6 49 17 2.6 SEG03
CL1046 SEG33 SEG3 IC1001 IC1002 IC1003 IC1004
2.6 50 16 2.6 SEG02 TC7SH125FU TC7SH125FU TC7SH125FU TC7SH125FU
CL1047 SEG34 SEG2
COM0 2.6 51
COM0 SEG1
15 2.6 SEG01 IC1001 IC1002 IC1003 IC1004
COM1 2.6 52 14 2.6 SEG0 BUS BUFFER BUS BUFFER BUS BUFFER BUS BUFFER

IN_A
GND

IN_A
GND

IN_A
GND
R1014 R1015 R1016

IN_A
GND
COM1 SEG0

G
470 330 150

G
2.6

0 0 3.3 3.3
F D1011

OSCIN

NC_11
COM2
COM3

VLCD
NC_3

TEST
INHB
1L043RW32EOCI7A11 (WHITE)

VDD

CSB

SDA
VSS

SCL
1 2 3 4 5 6 7 8 9 10 11 12 13
Q1000
2.6 2.6 5.2 5.2 5.2 0 0 0 5.2
LTC014EUBFS8TL
LED DRIVER 3.3

CL1057

CL1070
CL1072
CL1074
CL1076
CL1079
CL1081
CL1083
COM2
COM3
0.3

C1021

0
0 22p R1021
D1004 100
G

CN1007
R1005
1k
HL-364V620MZ-T
jo R1056
0

C1034 C1035
C1019
0.1u
C1020
0.1u

R1017
C1022
22p

C1023
22p

100
100
100
23P 0.1u 0.01u
CL1124
SW+13V 1
R1009 0 CL1016 R1052 0

R1018
R1019
R1020
M+5.2V 2
H M+5.2V 3 C1009
0.1u
C1012
1u CL1017
R1060
0
R1041 0
R1042 0
LED_GND 4
W1001 R1043 0
LED_GND 5
CL1018
LCD-SCL 6
CL1019
LCD-SDA 7
CL1020
LCD-CSB 8
CL1021
AD-KEY0 9
CL1022
AD-KEY1 10
I MOTHERBOARD DGND 11
BOARD E+3.3V 12
CL1014 CL1023
CN122 SIRCS 13
CL1025
POWER KEY 14
CL1026
MIC-VOL 15
CL1027
D+3.3V 16 EN1000
CL1005
RGB_SD 17 MIC LEVEL
CL1006
RGB_PWM 18 2 CL1113
J RGB_TRANS 19
CL1007
CL1008
3
1

RGB_SCLK 20 S1000
CL1024 1 C1025 R1040
LCD_BCK_LED/LCD_INHB 21
CL1009 R1013 0.001u 10k
PANEL_LED_CTRL 22
CL1125
DGND 23

K 1 2 3 4 5 6 7 8 9 10 11 12 13

>001S
PANEL BOARD
(2/2)
(Page 41)

SA-WGT4D
40 40
 SA-WGT4D

6-10. SCHEMATIC DIAGRAM - PANEL Board (2/2) -

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
>001S
PANEL BOARD
A (1/2)
(Page 40)

1 2 3 4 5 6 7 8 9 10 11 12 13

PANEL BOARD (2/2)

CL1094 CL1100
B S1019 S1018
VOCAL FIESTA
R1022 FADER R1028
680 680

CL1095 CL1101
S1006 S1017

CN1003 MIC MEGA

9P ECHO BASS
R1023 R1029
C SIRCS 1
CL1011 1k 1k

>002S NC 3
CL1012
CL1096 CL1102
CL1123 S1001 S1007
DGND 4
MIC_IR BOARD E+3.3V 5
CL1013 Z x
R1024 R1030
CN1101 SW_BLUE_LED 6
CL1115
1.5k 1.5k
CL1116
(Page 45) SW_RED_LED 7
CL1117
SW_GREEN_LED 8 CL1097 CL1103
D SW+13V 9
CL1118 S1002 S1008
R1055 TUNING + N
0 R1025 > R1031
1.5k 1.5k

i
CL1098 CL1104
S1003 S1009
TUNING - — PAIRING
R1026 . BLUETOOTH R1032
CN1004 2.2k 2.2k

m
E 11P
CL1028
LED_GND 1
LED_GND 2 CL1099 CL1105
CL1030 S1004 S1010
RGB_SD 3
CL1029
M+5.2V 4 - FUNCTION
CL1032 R1027
GESTURE_RGB RGB_TRANS 5
CL1031 3.3k
R1033
3.3k
BOARD RGB_PWM 6
CL1112
SIN 7 CL1106
F CN1400 RGB_SCLK 8
CL1033 S1005 S1011
CL1114 + ENTER
AD_KEY0 9 R1034
CL1034
D3.3V 10 4.7k
CL1035 R1039
DGND 11 4.7k
CL1107
S1012
CN1006 REC TO USB
13P R1035
CL1060 6.8k
M+5.2V 1
CL1062
G

H
>003S
RGB_SPLITTER
BOARD
CN1250
(Page 47)
LED_GND
LED_GND
LED_GND
RGB_SCLK
D+3.3V
SIN
BLUETOOTH
RGB_TRANS
RGB_PWM 10
SW_BLUE_LED 11
SW_RED_LED 12
SW_GREEN_LED 13
2
3
4
5
6
7
8
9
CL1061
CL1067

CL1063
CL1064
CL1066
CL1065
CL1084
CL1119
CL1120
jo D1012
HL-364B460MZ-T
S1013
FOOTBALL

S1014
PARTY
CHAIN

S1015
CL1108

R1036
10k

CL1109

R1037
15k

CL1110

PARTY
LIGHT R1038
22k

I S1016
CL1111

SOUND
FIELD

VBUS CN1001
D-
J CN1000 D+
REC/PLAY

5P GND 5V 1A
CL1000
VBUS 1
MOTHERBOARD C1001
100u
C1003 C1004
CL1001 10u 0.01u
BOARD D- 3
CL1002
6.3V W1003

CN451 D+ 4
CL1003
USB_GND 5
CL1004

SA-WGT4D
41 41
SA-WGT4D

6-11. PRINTED WIRING BOARD - GESTURE_MODULE PC BOAR Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

GESTURE_MODULE PC BOAR BOARD GESTURE_MODULE PC BOAR BOARD

(COMPONENT SIDE) (CONDUCTOR SIDE)
B

C
CL1324

R1305
D1302
R1304

D1303
i
D1306
D1301
D1307

D1305
R1303 JL1303

R1301
JL1302
JL1304
D1300 JL1301

D1304

CL1313
CL1315
CL1317
CL1320
CL1327
2 6 2 6
CN1300 CN1300

R1306
E

CL1307
m
1 7 1 7 JL1305 R1300

CL1309
CL1300
JL1300

CL1311
R1309
CL1301 CL1306 CL1302
R1302
R1316

R1308
C1304
C1317

CL1304
14 1 CL1325 R1319
CL1322

CL1310

R1314
IC1300
>005P
CL1326
R1310 15 28

C1315
C1302

CL1316

CL1328
MOTHERBOARD CL1319 CL1303

C1314
R1317
R1311

R1312
BOARD

C1305
CL1305

R1315
F

CL1323
CN120
CL1331

CL1308
CL1312
CL1314

CL1318
CL1321
CL1329
(Page 36) C1307
C1310

H
jo 1-980-558-
11
(11)
CL1330

1-980-558-
11
(11)

SA-WGT4D
42 42
 SA-WGT4D

6-12. PRINTED WIRING BOARD - GESTURE_RGB Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

GESTURE_RGB BOARD PANEL BOARD

CN1004
(Page 39)
B
>007P

11 1
CN1400
10 2
CL1409
CL1410
C

D1406
R1435
R1436 CL1400 C1400

R1406
C1426 R1437

C1429
JR1412

JR1410
C1427

JR
JR

JR1417
JR1415 JR

R1442
C1430
JR
JR JR1414
R1438 CL1414
JR1416 R1439 CL1412

C1428
JR R1440 CL1437
CL1435 C1431 R1428
C1432

CL1434 CL1439 R1430 CL1413

D

JR1413 JR1407
CL1433 S1400

JR
CL1432

JR1400 JR1411
CL1436 R1429 CL1415
CL1438

GESTURE CONTROL

JR

JR1405
CL1431

JR1408
C1415
VOLUME +
CL1429

JR
JR1409

JR

JR
C1414 C1424

12 1
CL1440
JR

IC1400 13
C1416

25

JR

i
CL1430 24 CL1411 CL1402
C1423

C1411

CL1423 CL1420
R1441
JR1406

CL1416 CL1428 C1404

JR
R1434
R1433
R1410

R1419
CL1422 C1403
E

m
C1407
R1412

R1420

CL1424
R1411C1410 C1408
R1413

R1417

S1406 D1405 C1409

CL1419
R1414

GESTURE CONTROL
R1416

GESTURE ON/OFF CL1426 CL1418

CL1425 CL1427 D1408
R1415

JR JR1402
CL1408

R1400
JR JR1404
JR
JR1401 CL1403
F
S1401
GESTURE CONTROL
VOLUME –
R1405

G
jo R1401
CL1404
D1407

D1401 D1404
S1402
GESTURE CONTROL
LIGHT
H CL1407 R1404
R1402
D1402 D1403
S1405
GESTURE CONTROL S1404 S1403
PLAYBACK GESTURE CONTROL GESTURE CONTROL
DJ SAMPLER
R1403
CL1406 CL1405

I 11
1-980-559- (11)

SA-WGT4D
43 43
SA-WGT4D

6-13. PRINTED WIRING BOARD - MIC_IR Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

MIC_IR BOARD

B
J1101 J1100
MIC2 MIC1

4
D D1102 1 2 3
C1128

K
A/K
A W1100
IC1100

i
CL1175

C1102
JR3301
JR

m R1104
CL1172 CL1155
Z7 CL1176 CL1173

R1103
C1122
C1125

CL1177
R1124

R1121 CL1171 C1101

CL1156
C1126
R1122

CL1174
C1121
R1125
R1113

R1123 CL1154
R1120

F R1105 CL1169
R1125

C1127
C1107

C1108

CL1163 JR
JR3302
R1109 CL1180
K

CL1168 CL1170
IC1101

K/A

R1110 CL1161 CL1162

C1129
R1112

A
R1117

D1101

CL1167 CN1101
CL1165
C1120

R1126

C1106 CL1160 1 7
CL1152
C1109
R1114

CL1164
CL1183 C1130
R1127
A

C1115 CL1179 CL1181

D1104

JR3305
R1100

G R1129 CL1159
jo R1131 JR
CL1166
>008P
K

R1101 R1115 LP1100

CL1153
PANEL BOARD
4

C1113

CL1150 C1112
R1134
R1133
R1135
CN1102

CN1003
JR

>009P C1114 CL1158

JR
(Page 39)
R1130

R1102
JR3303

CL1151 JR3399 Z6 CL1182

SW_RGB_L CL1184
R1116

A K
C1116
1

CL1157
BOARD 1 5 R1128
D1103
CN1700 CL1185 CN1100
H (Page 48) CL1186
11
1-980-561- (11)

>001P
I MOTHERBOARD BOARD
CN601
(Page 36)

SA-WGT4D
44 44
 SA-WGT4D

6-14. SCHEMATIC DIAGRAM - MIC_IR Board -

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

MIC_IR BOARD

CN1100
5P R1101
CL1150 0
B MOTHERBOARD
A+9V 1

CL1151
BOARD MIC_GND 3
CL1152
CN601 MIC_SIGNAL 4
CL1153
MIC_DET 5
R1130 R1128 R1127 R1129
39k 18k 18k 39k

C1120 R1126
D1104 0.0018u 100k
C D1103 C1106
2.2u
DA2J10100L
DA2J10100L R1110 50V
100 CL1164 CL1167
R1100 R1102
0 0 CL1161 R1117 C1129
8.9 8 4.4
C1109 R1114 VCC OUT1 0 0.0018u
IC1101
470p 68k 4.4 7 BA4558F 2 4.4
OUT2 -IN1
4.4

4.4
6
-IN2 IC1101 +IN1
3 4.4 CL1168
CL1165 5 MIC AMP 4
+IN2 VEE CL1169
C1105 R1109 R1112
D 0.1u 100K 1.2k
C1115
0.1u C1130
2.2u CL1170
50V 6
R1115 R1116 CL1175 7
CL1171 CL1173 2 J1100
R1113 10k 10k CL1176 1

i
100k 5 MIC1
C1114 C1121 R1120 4
220u 2.2u 1k 3
CL1163
10V R1131 R1125 R1124 50V C1127
CL1166
CL1162 0 4.7k 4.7k 0.001u
C1112 C1116 R1122 C1126 D1101
E

m
C1107 C1108 0.1u 0.1u BAV99-215
1u 0.1u 22k 0.001u
50V 50V W1100
C1113 CL1174
220u D1102
10V
BAV99-215
C1128
0.001u
6
7
CL1172 CL1177 2 J1101
1
5 MIC2
F C1122
2.2u
R1121
1k R1123 C1125
4
3
50V 22k 0.001u

C1101
100p
CN1101
G

H
>002S
PANEL BOARD
(2/2)
CN1003
(Page 41)
SIRCS 1
DGND 2
E+3.3V 3
SW_BLUE_LED 4
SW_RED_LED 5
SW_GREEN_LED 6
SW+13V 7
7P
CL1154
CL1155
CL1156
CL1179
CL1180
CL1181
CL1182
jo R1103
0

R1104
47
C1102
1u
3.1

3.3

R1133
R1135
R1134
1
2
3
VO
GND
VCC

100
150
100
IC1100
PNA4823M05S0

IC1100
REMOTE CONTROL
RECEIVER

CL1183
CL1184
CL1185
CN1102
4P
4 SW_BLUE_LED
3 SW_RED_LED
2 SW_GREEN_LED
SW_RGB_L BOARD
>004S

CL1186
1 SW+13V CN1700
(Page 48)

SA-WGT4D
45 45
SA-WGT4D

6-15. PRINTED WIRING BOARD - RGB_SPLITTER Board - • See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

RGB_SPLITTER BOARD
BAR_RGB_A BOARD BAR_RGB_A BOARD
(LEFT) (RIGHT)
B CN1600 CN1600
SS-GT4DB SS-GT4DB
(Page 5) (Page 6)
>010P >011P

C
CN1251 FB1251 CN1252 C1274
1 7 1 7
C1286 C1285
C1279
C1288 C1271
C1284
R1253
R1252

C1269
R1251

C1287
R1268
R1269
C1277
C1283

R1267
C1266
R1254

R1257

R1266
R1256

FB1250
R1255

CL1275
C1270 R1270
CL1263
D
C1259
C1260

C1268

C1261 CL1262 CL1271 CL1272

C1258 C1273
JR3356
CL1265

JR3310
C1263

JR3357

i
JR
JR3311 JR JR JR
CL1266 CL1274
C1257 CL1267 CL1273
CL1264

C1251
C1275
13

12
CL1269

C1278
IC1250

C1256 CL1270 R1272

JR3308

CL1277
C1281

CL1268
CL1255
25

JR

C1255
CL1276

m
CL1259 JR3312
R1259
24

CL1278
1

CL1260
R1275

JR
C1282
R1271 C1280

E CL1279
R1263
R1260 JR3319 C1276 R1264
CL1280
R1273

CL1250 CL1261 C1264 JR

R1265
R1261 CL1281
CL1251 C1265 CL1256
CL1254 CL1283
2 12
CN1250 CL1252
JR3314

1 13
CL1253
JR

CL1257
F JR
JR3304 CL1282
11
jo 1-980-562- (11)

G >006P
PANEL BOARD
CN1006
(Page 39)

SA-WGT4D
46 46
 SA-WGT4D

6-16. SCHEMATIC DIAGRAM - RGB_SPLITTER Board - • See page 49 for IC Block Diagrams.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

RGB_SPLITTER BOARD

B
CN1250
13P C1251
CL1253 0.1u
M+5.2V 13
LED_GND 12
LED_GND 11
CL1255
LED_GND 10
>003S CL1254
C RGB_SCLK 9

PANEL BOARD D3.3V 8

CL1256
SIN 7
(2/2) BLUETOOTH 6
CL1250

CN1006 RGB_TRANS 5
CL1252
CL1251
(Page 41) RGB_PWM 4
CL1257
SW_BLUE_LED 3
CL1282
SW_RED_LED 2
CL1283
D SW_GREEN_LED 1

i
m
E C1283
0.01u
C1284
0.01u
C1285
0.01u C1266
C1286
CN1251 0.01u
FB1250 C1287 0.01u C1269
7P
>005S M+5.2V 1
0uH
C1288 0.01u 0.01u
C1271

0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u

0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u IC1250 0.01u
BAR_RGB_A BOARD BAR_L_A_BLUE_LED 2 TC62D723FNG C1274 CN1252
F BAR_L_A_RED_LED 3 IC1250
0.01u C1277 FB1251 7P >006S
(LEFT) 0uH

C1255
C1256
C1257
C1258
C1259
C1260
C1261
C1263

C1268
C1270
C1273
C1275
C1278
C1280
C1281
C1282
0.01u C1279
BAR_L_A_GREEN_LED 4 LED DRIVE 1 M+5.2V
CN1600 BAR_L_B_BLUE_LED 5
0.01u
2 BAR_R_A_BLUE_LED BAR_RGB_A
R1255 33 CL1262 0.1 CL1271 R1266 100
BOARD
0
SS-GT4DB BAR_L_B_RED_LED 6
R1256 33 CL1263 0 13
OUT8 OUT7
12 0.1 CL1272 R1267 33
3 BAR_R_A_RED_LED

(Page 5)
BAR_L_B_GREEN_LED 7
R1257 100 CL1264 0 14
OUT9 OUT6
11 0.1 CL1273 R1268 33
4 BAR_R_A_GREEN_LED
(RIGHT)
OUT10 OUT5 5 BAR_R_B_BLUE_LED
R1251 33 CL1265 0 15
OUT11 OUT4
10 0.1 CL1274 R1269 100
6 BAR_R_B_RED_LED
CN1600
R1252 33 CL1266 0 16
OUT12 OUT3
9 0 CL1275 R1270 33
7 BAR_R_B_GREEN_LED SS-GT4DB
R1253 100 CL1267 0 17 8 5.1 CL1276 R1271 100
G OUT13 OUT2 (Page 6)

H
jo R1254
R1260
R1261
R1259
820
33
33
100
R1275
0
CL1268
CL1269
CL1270
CL1259
CL1260
CL1261
0

3.3
18
19
20
21
22
23
24
25
OUT14
OUT15
PWMCLK
SOUT
REXT
VDD

C1264
0.22u
OUT1
OUT0
TRANS
SCK
SIN
GND
7
6
5
4
3
2
1
10.3

5.1

0
CL1277
CL1278
CL1279
CL1280
CL1281

C1276
100p
R1263
R1264
R1265
100
100
100
R1272
R1273
150
100

C1265
10u
16V

SA-WGT4D
47 47
SA-WGT4D

6-17. PRINTED WIRING BOARD - SW_RGB_L Board, SW_RGB_R Board -

• See page 35 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8

A
SW_RGB_L BOARD SW_RGB_R BOARD

CL1752
CL1753

JR1750
5

JR
CN1750 1
CL1754
JR1700

C D1700

4
10

CL1751

6
8

D1750
JR

CL1702
CN1700

CL1703
CL1700 CL1701
>009P
D
1

MIC_IR BOARD

i
CN1102
9

11 11
(Page 44)
1-980-587- (11) 1-980-588- (11)

m
E

6-18. SCHEMATIC DIAGRAM - SW_RGB_L Board, SW_RGB_R Board -

1 2 3 4
jo 5 6 7 8 9 10

SW_RGB_L BOARD SW_RGB_R BOARD

B
GRN
RED
BLU

SW_R_BLUE_LED 8
SW_R_RED_LED 7
SW_R_GREEN_LED 6 D1750
DI_LTRB R8SF
SW+13V 5
CL1700 CL1751
>004S SW+13V 4
CL1701 GRN
SW+13V 4
CL1752
SW_GREEN_LED 3 SW_GREEN_LED 3

C MIC_IR BOARD SW_RED_LED 2

CL1702 RED
BLU
SW_RED_LED 2
CL1753
CL1703 CL1754
CN1102 (Page 45) SW_BLUE_LED 1 SW_BLUE_LED 1

CN1700 CN1750
8P D1700 4P
DI_LTRB R8SF

SA-WGT4D
48 48
 SA-WGT4D

• IC Block Diagrams
IC1000 BU9795AKS2 (PANEL BOARD (1/2))

SEG34

SEG33

SEG32

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24
COM1

COM0

52 51 50 49 48 47 46 45 44 43 42 41 40
COM2 1 39 SEG23

COM3 2 38 SEG22

LCD voltage generator Segment 37 NC_37

NC_3 3 Common
driver driver
36 SEG21
VLCD 4
+

VDD 5
–
LCD BIAS 35 SEG20
SELECTOR
Common Blink timing
VSS 6
+
DDRAM 34 SEG19
–
counter generator

OSCIN 7 33 SEG18

32 SEG17
CSB 8 Command Command
register Data Decoder 31 SEG16
SCL 9 OSCILLATOR Power On Reset Serial inter face
30 SEG15
SDA 10
IF FILTER
29 NC_29
NC_11 11

28 SEG14
TEST 12

INHB 13 27 SEG13
14 15 16 17 18 19 20 21 22 23 24 25 26
SEG0

SEG1

SEG2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

IC1001, IC1002, IC1003, IC1004 TC7SH125FU (PANEL BOARD (1/2))

G 1 5 VCC

i
m
IN_A 2

GND 3 4 OUT_Y

IC1250 TC62D723FNG (RGB_SPLITTER BOARD)

jo
GND 1

16 25 GND
SIN 2 Error detection result Output open/short detection circuit POR
data register 16 circuit 24 VDD
SCK 3

TRANS 4 Constant current output circuit Reference

voltage
OUT0 5
Output delay circuit 23 REXT
OUT1 6 16
8-bit
0-bit 15-bit
TSD DAC
Output ON/OFF setting data register circuit
8
Comparator

Comparator

Comparator

PWM
OUT2 7 countor

OUT3 8

OUT4 9 16 16 16
OUT5 10 PWM data registor
16-bit 16-bit Registor 3 16-bit
OUT6 11 POD PWM Data PWM Data PWM Data
circuit for OUT0 for OUT1
(for output)
for OUT15
OUT7 12 16 16 16 16-bit x 2
State setting
16-bit 16-bit Registor 2 16-bit register
OUT8 13 16 PWM Data 16 PWM Data 16 PWM Data
for OUT0 for OUT1 (for synchronous) for OUT15
OUT9 14 16 16 16
16-bit 16-bit 16-bit
OUT10 15 Registor 1 PWM Data
PWM Data PWM Data
16 for OUT0 for OUT1 for OUT15
16
OUT11 16
16 16 16
OUT12 17 Command
control Data transfer control circuit
OUT13 18 circuit

OUT14 19 16 16

0-bit 15-bit
16-bit shift registor
SOUT
selection 22 SOUT
circuit
F/F

20 21
PWMCLK
OUT15

49
SA-WGT4D
Ver. 1.2 SECTION 7
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • Abbreviation The components identified by mark 0
they may have some difference from the AR : Argentina model or dotted line with mark 0 are critical for
original one. AUS : Australian model safety.
• Items marked “*” are not stocked since E4 : African model Replace only with part number specified.
they are seldom required for routine ser- E12 : 220 – 240 V AC area in E model
vice. Some delay should be anticipated EA : Saudi Arabia model
when ordering these items. The components identified by mark 9 con-
LA9 : Latin-American model
tain confidential information.
MY : Malaysia model
• The mechanical parts with no reference Strictly follow the instructions whenever the
RU : Russian model
number in the exploded views are not sup- components are repaired and/or replaced.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
 
Parts Color Cabinet’s Color

7-1. SIDE PANEL SECTION

top panel section #1

#1

#1

i
m
1
#1

ns #1
jo
3
loading panel,
back panel section

#1
2

ns

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-464-752-11 SCREW, TAPPING (HEX) #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
2 X-2593-201-1 SIDE PANEL R, ASSY ns not supplied
3 X-2593-200-1 SIDE PANEL L, ASSY

50
 SA-WGT4D
Ver. 1.2

7-2. TOP PANEL SECTION

52
ns
#2
#2 ns

53

#2

#2 51
#2
#2 54
PANEL board (ns)

ns
55
ns #2
#2
#2 #2 ns
#2 #2 #2
#2
RGB_SPLITTER
56 ND1000 board (ns)

57

i
m
58

56 ns

56
jo
56
60

59 56
ns
56 56

61
62
ns

Note 1: When the RC-S730 (WW) is replaced, refer to “NOTE Note 2: If wire (flat type) is replaced, install it after bending it in the
OF REPLACING THE COMPLETE MOTHERBOARD same form as that before replacement.
BOARD, BLUETOOTH MODULE AND RC-S730 (WW)”
on page 6.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 1-828-330-21 WIRE (FLAT TYPE) (13 CORE) 59 1-849-015-11 WIRE (FLAT TYPE) (6 CORE)
52 1-828-004-21 WIRE (FLAT TYPE) (23 CORE) 60 8-989-602-00 RC-S730 (WW)
53 1-828-303-21 WIRE (FLAT TYPE) (7 CORE)
54 1-828-316-21 WIRE (FLAT TYPE) (11 CORE) 61 4-581-422-01 KNOB MIC
55 A-2085-932-A GESTURE_RGB BOARD, COMPLETE 62 X-2592-590-2 PANEL, TOP ASSY
ND1000 1-493-124-11 LIQUID CRYSTAL DISPLAY
56 4-543-517-02 HEMILON, 5X5X0.4 #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
57 X-2592-593-3 BUTTON, GESTURE ASSY ns not supplied
58 A-2085-930-A GESTURE_MODULE PC BOAR
BOARD, COMPLETE

51
SA-WGT4D

7-3. LOADING PANEL, BACK PANEL SECTION

• Rear side view

ns
ns
#2

ns 102
#2

101
ns

CDM block section

#1

MOTHERBOARD board,
3CH DAMP board section

i
m
jo

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 X-2592-592-1 PANEL, LOADING ASSY #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
102 4-295-431-01 SPRING, LOADING ns not supplied
#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3

52
 SA-WGT4D

7-4. CDM BLOCK SECTION

#2

DVD mechanism section

(CDM90-DVBU204//M)

152

152 155
ns
151
155
151
151 ns

151 152

i
m
152 155
154

155
153

154
jo
153

ns

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 2-345-115-01 SCREW (S), FLOAT 155 4-533-382-01 INSULATOR
152 4-535-577-01 STEP SCREW M2.6
153 4-533-939-01 SPRING, INSULATOR (F) #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
154 4-533-940-01 SPRING, INSULATOR (R) ns not supplied

53
SA-WGT4D

7-5. DVD MECHANISM SECTION

(CDM90-DVBU204//M)

ns
201 (including MS-476 board)

ns

203

202
203

203 204

ns
i
m
ns

ns
jo
MS-476 board
(ns)

205
ns

207

206

ns

Note: If wire (flat type) is replaced, install it after bending

it in the same form as that before replacement.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 A-1896-391-B LOADING COMPLETE ASSY (T) 205 1-849-478-11 WIRE (FLAT TYPE) (24 CORE)
(including MS-476 board)
202 3-087-599-01 INSULATOR SCREW 206 1-469-829-11 CORE, FERRITE
203 2-634-618-21 INSULATOR 207 1-828-293-21 WIRE (FLAT TYPE) (5 CORE)
0 204 A-2046-956-A SERVICE, OPTICAL DEVICE (7G) ns not supplied

54
 SA-WGT4D
Ver. 1.2

7-6. MOTHERBOARD BOARD, 3CH DAMP BOARD SECTION

• Rear side view
254
ns

255
#2
#2
256
251 253

A
#2
#2 252

ns

SWITCHING REGULATOR
(SSN-161AD) section

i
m
#2

#3
#2
jo

Note 1: When the complete MOTHERBOARD board is replaced, Note 2: If wire (flat type) is replaced, install it after bending it in the
refer to “NOTE OF REPLACING THE COMPLETE same form as that before replacement.
MOTHERBOARD BOARD, BLUETOOTH MODULE AND
RC-S730 (WW)” on page 6.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 1-828-362-21 WIRE (FLAT TYPE) (19 CORE) 9 252 A-2126-572-A MOTHERBOARD BOARD, COMPLETE
9 252 A-2121-657-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (MY)
(for SERVICE) (AR, LA9) * 253 3-703-150-11 CLAMP
9 252 A-2121-659-A MOTHERBOARD BOARD, COMPLETE 254 3-905-609-31 SCREW (TRANSISTOR)
(for SERVICE) (AEP, UK)
9 252 A-2121-660-A MOTHERBOARD BOARD, COMPLETE 255 4-585-699-01 SHEET, THERMAL
(for SERVICE) (RU) 256 A-2084-264-A 3CH DAMP BOARD, COMPLETE
9 252 A-2121-661-A MOTHERBOARD BOARD, COMPLETE (EA, AR, E4, E12, LA9)
(for SERVICE) (AUS) 256 A-2124-214-A 3CH DAMP BOARD, COMPLETE
(AEP, UK, RU, MY, AUS)
9 252 A-2121-663-A MOTHERBOARD BOARD, COMPLETE #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
(for SERVICE) (E12) #3 7-682-547-04 SCREW +B 3X6
9 252 A-2121-664-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (EA, E4) ns not supplied

55
SA-WGT4D
Ver. 1.2

7-7. SWITCHING REGULATOR (SSN-161AD) SECTION

• Rear side view
#2
303
304 #2
302 ns
303
ns ns
303
302
303 302
302 301 #2
#2 306

301 #2

ns
ns
ns
ns
ns
#2 #2
ns
#2 #2
306 #2
301 ns #2

#2 #2
#2 ns

305

i
m
chassis section
jo

Note: When the SWITCHING REGULATOR (SSN-161AD) board

is replaced, spread the bond referring to “BOND FIXATION
OF ELECTRICAL PARTS” on page 8.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 301 3-703-150-11 CLAMP 306 4-532-205-61 ACOUSTIC TAPE
302 4-537-542-01 STEP SCREW B3X6 #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
303 4-585-365-01 DAMPER, SIDE A ns not supplied
0 304 1-855-340-11 DC FAN
0 305 1-474-657-11 REGULATOR, SWITCHING (SSN-161AD)

56
 SA-WGT4D

7-8. CHASSIS SECTION

• Rear side view

351
ns

ns ns
ns
ns
ns ns
ns
ns
ns
front panel section ns
353 #2

ns
352
ns #2

352
ns #2 #2

#2
#2 353

353 353

ns

i
ns
m
ns
jo

SPK cabinet (SW),

allay cover section

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
351 1-457-369-12 CORE, FERRITE #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
* 352 3-703-150-11 CLAMP ns not supplied
353 4-874-614-52 SCREW (1) (3.5X20), TAPPING

57
SA-WGT4D
Ver. 1.2

7-9. FRONT PANEL SECTION

ns
ns
ns 407
ns

402

401
ns

MIC_IR board
(ns)
ns
#2

ns 403
#1 #2

404

#2
#2

i
m
#1 ns
405
#1
406
jo
406
ns

Note 1: When the BLUETOOTH module is replaced, refer to Note 2: If wire (flat type) is replaced, install it after bending it in the
“NOTE OF REPLACING THE COMPLETE MOTHER- same form as that before replacement.
BOARD BOARD, BLUETOOTH MODULE AND RC-S730
(WW)” on page 6.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 1-828-702-61 WIRE (FLAT TYPE) (10 CORE) 406 4-578-508-01 FOOT
402 1-492-699-31 BLUETOOTH MODULE 407 X-2592-591-2 PANEL, FRONT ASSY (SW)
* 403 3-703-150-11 CLAMP #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
404 A-2087-151-A SW_RGB_R BOARD, COMPLETE #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
405 A-2087-150-A SW_RGB_L BOARD, COMPLETE ns not supplied

58
 SA-WGT4D
Ver. 1.2

7-10. SPK CABINET (SW), ALLAY COVER SECTION

451

458 451
ns
451
handle section
460 451

451
#4 451
ns 457
455 #4
451

#4 459

453
453 461
454
ns
#4
451

451

i
m
456

453
452 453 454
jo

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
451 4-238-407-12 SCREW (1) (4X20), +BV TAPPING 458 1-457-369-12 CORE, FERRITE
452 1-859-161-21 LOUDSPEAKER (25CM) 459 4-591-595-11 ALLAY PORON
453 4-532-593-02 SCREW (4X13) (TR-184A) 460 4-584-819-01 CABLE CLIP
454 4-578-508-01 FOOT
455 A-2093-301-A CASTER ASSY (L) 461 4-581-396-01 ALLAY COVER
#4 7-685-647-71 SCREW +BVTP 3X10 TYPE2 IT-3
456 A-2093-302-A CASTER ASSY (R) ns not supplied
* 457 3-703-150-11 CLAMP

59
SA-WGT4D
Ver. 1.2

7-11. HANDLE SECTION

524
521
522
522
529 528
B B
C
527 521
523 525
ns 528
C
ns
520
ns
ns 504
526
ns 519
ns
526

518

515 516
508

i517
m
514
513
512
511
#2 504
503 509 510
506
jo
501
ns
505

507 504

502 501

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
501 4-584-818-01 SLIDER PIPE 517 4-581-402-01 PIPE HOLDER 2
502 4-581-452-11 SHAFT PULLER 1 518 4-584-816-01 ALLAY PIPE 2
503 4-581-399-01 ALLAY PULLER 519 4-591-713-01 HANDLE SHEET
504 4-567-203-01 SHAFT (S) 520 4-567-204-01 SHAFT (L)
505 4-581-398-01 PUSH BUTTON
521 4-464-752-21 SCREW, TAPPING (HEX)
506 4-591-595-01 ALLAY PORON 522 4-581-410-01 HANDLE PIVOT
507 4-581-397-01 PIPE GUIDE 523 3-906-887-01 SCREW (+BTP) (DIA. 3) (BZN-N)
508 4-584-815-01 ALLAY PIPE 1 524 4-581-405-01 HANDLE TOP CASE
509 4-581-403-01 PIPE2 CAB 525 4-581-407-02 HANDLE TOP
510 4-591-712-01 PIPE 2 CAP CUSHION
526 4-581-416-01 STOPPER BAR
511 4-581-404-01 PIPE2 SLIPER 527 4-581-413-01 HANDLE BASE FRONT
512 4-581-401-01 PIPE FIX2 528 4-581-414-01 BAR LOCKER
513 4-581-418-01 FIX SPACER 529 4-581-412-02 HANDLE BASE BACK
514 4-581-453-01 SHAFT BAR LOCKER #2 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
515 4-581-409-01 SPRING, COMPRESSION
ns not supplied
516 4-581-400-01 PIPE2 STOPPER

60
 SA-WGT4D
SECTION 8 Ver. 1.2
3CH DAMP
ELECTRICAL PARTS LIST
GESTURE_MODULE PC BOAR
GESTURE_RGB MIC_IR MOTHERBOARD MS-476 PANEL
Note:
• Due to standardization, replacements in • COILS
When indicating parts by reference num-
the parts list may be different from the uH: μH
ber, please include the board name.
parts specified in the diagrams or the com- • SEMICONDUCTORS
ponents used on the set. In each case, u: μ, for example: The components identified by mark 0
• -XX and -X mean standardized parts, so uA. . : μA. . , uPA. . , μPA. . , or dotted line with mark 0 are critical for
they may have some difference from the uPB. . : μPB. . , uPC. . , μPC. . , safety.
original one. uPD. . : μPD. . Replace only with part number specified.
• Items marked “*” are not stocked since • Abbreviation
they are seldom required for routine ser- AR : Argentina model The components identified by mark 9
vice. Some delay should be anticipated AUS : Australian model contain confidential information.
when ordering these items. E4 : African model Strictly follow the instructions whenever the
• RESISTORS E12 : 220 – 240 V AC area in E model components are repaired and/or replaced.
All resistors are in ohms. EA : Saudi Arabia model
METAL: Metal-film resistor. LA9 : Latin-American model
METAL OXIDE: Metal oxide-film resistor. MY : Malaysia model
F: nonflammable RU : Russian model
• CAPACITORS
uF: μF

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-2084-264-A 3CH DAMP BOARD, COMPLETE J1101 1-822-967-12 JACK (MIC2)
(EA, AR, E4, E12, LA9)
A-2124-214-A 3CH DAMP BOARD, COMPLETE < JUMPER RESISTOR >
(AEP, UK, RU, MY, AUS)
******************** JR3301 1-216-296-11 SHORT CHIP 0

< IC >

i JR3302 1-216-296-11 SHORT CHIP

JR3303 1-216-296-11 SHORT CHIP
0
0
m
JR3305 1-216-296-11 SHORT CHIP 0
IC1005 6-722-001-01 IC 78D12AG-TN3-R JR3399 1-216-296-11 SHORT CHIP 0
IC1006 6-722-002-01 IC 78D07AG-TN3-R *************************************************************
IC1007 6-722-003-01 IC 79D07AG-TN3-R
************************************************************* 9 A-2121-657-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (AR, LA9)
A-2085-930-A GESTURE_MODULE PC BOAR BOARD, 9 A-2121-659-A MOTHERBOARD BOARD, COMPLETE
COMPLETE (for SERVICE) (AEP, UK)
********* 9 A-2121-660-A MOTHERBOARD BOARD, COMPLETE
jo
(for SERVICE) (RU)
************************************************************* 9 A-2121-661-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (AUS)
A-2085-932-A GESTURE_RGB BOARD, COMPLETE 9 A-2121-663-A MOTHERBOARD BOARD, COMPLETE
***************************** (for SERVICE) (E12)

************************************************************* 9 A-2121-664-A MOTHERBOARD BOARD, COMPLETE

(for SERVICE) (EA, E4)
MIC_IR BOARD 9 A-2126-572-A MOTHERBOARD BOARD, COMPLETE
************ (for SERVICE) (MY)
***********************
< CONNECTOR >
*************************************************************
CN1101 1-564-709-11 PIN, CONNECTOR (SMALL TYPE) 7P
CN1102 1-564-706-11 PIN, CONNECTOR (SMALL TYPE) 4P MS-476 BOARD
************
< DIODE >
When the MS-476 board is defective, replace the LOADING COMPLETE ASSY (T).
D1101 6-500-400-01 DIODE BAV99-215 *************************************************************
D1102 6-500-400-01 DIODE BAV99-215
D1103 6-502-961-01 DI DA2J10100L PANEL BOARD
D1104 6-502-961-01 DI DA2J10100L ************

< IC > < CONNECTOR >

IC1100 6-600-780-01 IC PNA4823M05S0 ( ) CN1001 1-819-866-11 USB CONNECTOR (A) (REC/PLAY 5V 1A)
IC1101 8-759-909-71 IC BA4558F CN1004 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
CN1006 1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P
< JACK >

J1100 1-822-967-12 JACK (MIC1)

Note : When the complete MOTHERBOARD board is replaced,
refer to “NOTE OF REPLACING THE COMPLETE
MOTHERBOARD BOARD, BLUETOOTH MODULE AND
RC-S730 (WW)” on page 6.

61
SA-WGT4D
Ver. 1.1
PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CN1007 1-779-560-21 CONNECTOR, FFC (LIF (NON-ZIF)) 23P JR3043 1-216-296-11 SHORT CHIP 0
JR3044 1-216-296-11 SHORT CHIP 0
< DIODE > JR3045 1-216-296-11 SHORT CHIP 0

D1004 6-504-215-01 DI HL-364V620MZ-T JR3046 1-216-296-11 SHORT CHIP 0

D1011 6-503-770-01 DI 1L043RW32EOCI7A11 (WHITE) JR3047 1-216-296-11 SHORT CHIP 0
D1012 6-504-213-01 DI HL-364B460MZ-T JR3048 1-216-296-11 SHORT CHIP 0
JR3049 1-216-296-11 SHORT CHIP 0
< ROTARY ENCODER > JR3051 1-216-296-11 SHORT CHIP 0

EN1000 1-493-008-11 ENCODER, ROTARY (MIC LEVEL) JR3052 1-216-296-11 SHORT CHIP 0
JR3053 1-216-296-11 SHORT CHIP 0
< IC > JR3055 1-216-296-11 SHORT CHIP 0
JR3056 1-216-296-11 SHORT CHIP 0
IC1000 6-720-239-01 IC BU9795AKS2 JR3057 1-216-296-11 SHORT CHIP 0
IC1001 6-710-786-01 IC TC7SH125FU
IC1002 6-710-786-01 IC TC7SH125FU JR3058 1-216-296-11 SHORT CHIP 0
IC1003 6-710-786-01 IC TC7SH125FU JR3059 1-216-296-11 SHORT CHIP 0
IC1004 6-710-786-01 IC TC7SH125FU JR3060 1-216-296-11 SHORT CHIP 0
JR3061 1-216-296-11 SHORT CHIP 0
< JUMPER RESISTOR > JR3062 1-216-296-11 SHORT CHIP 0

JR3000 1-216-864-91 SHORT CHIP 0 JR3063 1-216-296-11 SHORT CHIP 0

JR3001 1-216-296-11 SHORT CHIP 0 JR3064 1-216-296-11 SHORT CHIP 0
JR3002 1-216-296-11 SHORT CHIP 0 JR3065 1-216-296-11 SHORT CHIP 0
JR3003 1-216-296-11 SHORT CHIP 0 JR3066 1-216-296-11 SHORT CHIP 0
JR3004 1-216-864-91 SHORT CHIP 0 JR3067 1-216-864-91 SHORT CHIP 0

JR3005 1-216-296-11 SHORT CHIP 0 JR3068 1-216-296-11 SHORT CHIP 0

JR3006
JR3007
JR3008
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
i JR3069
JR3070
JR3071
1-216-296-11
1-216-296-11
1-216-864-91
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
m
JR3009 1-216-296-11 SHORT CHIP 0 JR3072 1-216-296-11 SHORT CHIP 0

JR3010 1-216-296-11 SHORT CHIP 0 JR3073 1-216-296-11 SHORT CHIP 0

JR3011 1-216-296-11 SHORT CHIP 0 JR3074 1-216-296-11 SHORT CHIP 0
JR3012 1-216-296-11 SHORT CHIP 0 JR3075 1-216-296-11 SHORT CHIP 0
JR3013 1-216-296-11 SHORT CHIP 0 JR3076 1-216-296-11 SHORT CHIP 0
JR3014 1-216-296-11 SHORT CHIP 0 JR3077 1-216-296-11 SHORT CHIP 0

JR3015 1-216-296-11 SHORT CHIP 0 JR3078 1-216-296-11 SHORT CHIP 0

jo
JR3016 1-216-296-11 SHORT CHIP 0 JR3079 1-216-296-11 SHORT CHIP 0
JR3017 1-216-296-11 SHORT CHIP 0 JR3080 1-216-296-11 SHORT CHIP 0
JR3018 1-216-296-11 SHORT CHIP 0 JR3081 1-216-296-11 SHORT CHIP 0
JR3019 1-216-296-11 SHORT CHIP 0 JR3082 1-216-296-11 SHORT CHIP 0

JR3020 1-216-296-11 SHORT CHIP 0 JR3083 1-216-296-11 SHORT CHIP 0

JR3021 1-216-296-11 SHORT CHIP 0 JR3084 1-216-296-11 SHORT CHIP 0
JR3022 1-216-296-11 SHORT CHIP 0 JR3085 1-216-296-11 SHORT CHIP 0
JR3023 1-216-296-11 SHORT CHIP 0 JR3086 1-216-296-11 SHORT CHIP 0
JR3024 1-216-296-11 SHORT CHIP 0 JR3087 1-216-296-11 SHORT CHIP 0

JR3025 1-216-296-11 SHORT CHIP 0 JR3088 1-216-296-11 SHORT CHIP 0

JR3026 1-216-296-11 SHORT CHIP 0 JR3089 1-216-296-11 SHORT CHIP 0
JR3027 1-216-864-91 SHORT CHIP 0 JR3090 1-216-296-11 SHORT CHIP 0
JR3028 1-216-296-11 SHORT CHIP 0 JR3091 1-216-296-11 SHORT CHIP 0
JR3029 1-216-296-11 SHORT CHIP 0 JR3092 1-216-296-11 SHORT CHIP 0

JR3030 1-216-296-11 SHORT CHIP 0 JR3093 1-216-864-91 SHORT CHIP 0

JR3032 1-216-296-11 SHORT CHIP 0 JR3094 1-216-296-11 SHORT CHIP 0
JR3033 1-216-296-11 SHORT CHIP 0 JR3095 1-216-296-11 SHORT CHIP 0
JR3034 1-216-296-11 SHORT CHIP 0 JR3096 1-216-296-11 SHORT CHIP 0
JR3035 1-216-296-11 SHORT CHIP 0 JR3097 1-216-296-11 SHORT CHIP 0

JR3036 1-216-296-11 SHORT CHIP 0 JR3098 1-216-296-11 SHORT CHIP 0

JR3037 1-216-296-11 SHORT CHIP 0 JR3099 1-216-296-11 SHORT CHIP 0
JR3038 1-216-296-11 SHORT CHIP 0 JR3369 1-216-296-11 SHORT CHIP 0
JR3039 1-216-296-11 SHORT CHIP 0 JR3378 1-216-864-91 SHORT CHIP 0
JR3040 1-216-296-11 SHORT CHIP 0
< LIQUID CRYSTAL DISPLAY >
JR3041 1-216-296-11 SHORT CHIP 0
JR3042 1-216-296-11 SHORT CHIP 0 ND1000 1-493-124-11 LIQUID CRYSTAL DISPLAY

62
 SA-WGT4D
Ver. 1.2
PANEL RGB_SPLITTER SW_RGB_L SW_RGB_R

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< TRANSISTOR > < DIODE >

Q1000 6-552-936-01 TR LTC014EUBFS8TL * D1700 6-503-912-01 DI_LTRB R8SF

< SWITCH > < JUMPER RESISTOR >

S1000 1-762-875-21 SWITCH, TACTILE (1) JR1700 1-216-296-11 SHORT CHIP 0

S1001 1-762-875-21 SWITCH, TACTILE (Z) *************************************************************
S1002 1-762-875-21 SWITCH, TACTILE (TUNING + >)
S1003 1-762-875-21 SWITCH, TACTILE(TUNING − .) A-2087-151-A SW_RGB_R BOARD, COMPLETE
S1004 1-762-875-21 SWITCH, TACTILE ( −) *************************

S1005 1-762-875-21 SWITCH, TACTILE ( +) < CONNECTOR >

S1006 1-762-875-21 SWITCH, TACTILE (MIC ECHO)
S1007 1-762-875-21 SWITCH, TACTILE (x) CN1750 1-580-057-11 PIN, CONNECTOR (SMD) 4P
S1008 1-762-875-21 SWITCH, TACTILE (N)
S1009 1-762-875-21 SWITCH, TACTILE ( PAIRING BLUETOOTH) < DIODE >

S1010 1-762-875-21 SWITCH, TACTILE (FUNCTION) * D1750 6-503-912-01 DI_LTRB R8SF

S1011 1-762-875-21 SWITCH, TACTILE (ENTER)
S1012 1-762-875-21 SWITCH, TACTILE (REC TO USB) < JUMPER RESISTOR >
S1013 1-762-875-21 SWITCH, TACTILE (FOOTBALL)
S1014 1-762-875-21 SWITCH, TACTILE (PARTY CHAIN) JR1750 1-216-296-11 SHORT CHIP 0
*************************************************************
S1015 1-762-875-21 SWITCH, TACTILE (PARTY LIGHT)
S1016 1-762-875-21 SWITCH, TACTILE (SOUND FIELD) MISCELLANEOUS
S1017 1-762-875-21 SWITCH, TACTILE (MEGA BASS) **************
S1018 1-762-875-21 SWITCH, TACTILE (FIESTA)
S1019 1-762-875-21 SWITCH, TACTILE (VOCAL FADER) 51 1-828-330-21 WIRE (FLAT TYPE) (13 CORE)

RGB_SPLITTER BOARD
i
************************************************************* 52
53
54
1-828-004-21
1-828-303-21
1-828-316-21
WIRE (FLAT TYPE) (23 CORE)
WIRE (FLAT TYPE) (7 CORE)
WIRE (FLAT TYPE) (11 CORE)
m
******************* 59 1-849-015-11 WIRE (FLAT TYPE) (6 CORE)

< CONNECTOR > 60 8-989-602-00 RC-S730 (WW)

201 A-1896-391-B LOADING COMPLETE ASSY (T)
CN1250 1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P (including MS-476 board)
CN1251 1-564-723-11 PIN, CONNECTOR (SMALL TYPE) 7P 0 204 A-2046-956-A SERVICE, OPTICAL DEVICE (7G)
CN1252 1-564-723-11 PIN, CONNECTOR (SMALL TYPE) 7P 205 1-849-478-11 WIRE (FLAT TYPE) (24 CORE)
206 1-469-829-11 CORE, FERRITE
< FERRITE BEAD >
jo
207 1-828-293-21 WIRE (FLAT TYPE) (5 CORE)
FB1250 1-481-467-11 BEAD, FERRITE (CHIP) 251 1-828-362-21 WIRE (FLAT TYPE) (19 CORE)
FB1251 1-481-467-11 BEAD, FERRITE (CHIP) * 253 3-703-150-11 CLAMP
* 301 3-703-150-11 CLAMP
< IC > 0 304 1-855-340-11 DC FAN

IC1250 6-719-142-01 IC TC62D723FNG 0 305 1-474-657-11 REGULATOR, SWITCHING (SSN-161AD)

351 1-457-369-12 CORE, FERRITE
< JUMPER RESISTOR > * 352 3-703-150-11 CLAMP
401 1-828-702-61 WIRE (FLAT TYPE) (10 CORE)
JR3304 1-216-296-11 SHORT CHIP 0 402 1-492-699-31 BLUETOOTH MODULE
JR3308 1-216-296-11 SHORT CHIP 0
JR3310 1-216-296-11 SHORT CHIP 0 * 403 3-703-150-11 CLAMP
JR3311 1-216-296-11 SHORT CHIP 0 452 1-859-161-21 LOUDSPEAKER (25CM)
JR3312 1-216-296-11 SHORT CHIP 0 * 457 3-703-150-11 CLAMP
458 1-457-369-12 CORE, FERRITE
JR3314 1-216-296-11 SHORT CHIP 0
JR3319 1-216-296-11 SHORT CHIP 0
JR3356 1-216-296-11 SHORT CHIP 0
JR3357 1-216-296-11 SHORT CHIP 0
*************************************************************

A-2087-150-A SW_RGB_L BOARD, COMPLETE

************************* Note 1: If wire (flat type) is replaced, install it after bending it in
the same form as that before replacement.
< CONNECTOR >
Note 2: When the RC-S730 (WW) and BLUETOOTH module
* CN1700 1-691-551-11 PIN, CONNECTOR (SMD) 8P is replaced, refer to “NOTE OF REPLACING THE
COMPLETE MOTHERBOARD BOARD, BLUETOOTH
MODULE AND RC-S730 (WW)” on page 6.

Note 3: When the SWITCHING REGULATOR (SSN-161AD)

board is replaced, spread the bond referring to “BOND
FIXATION OF ELECTRIC PARTS” on page 8.

63
SA-WGT4D

REVISION HISTORY

Ver. Date Description of Revision

1.0 2016.02 New
1.1 2016.05 Addition of African, Argentina, 220 – 240 V AC area in E model, Malaysia, Russian, Saudi Arabia and
Thai models.
Change P/N of Ref. No. 57 and 62 in page 51.
Change P/N of Ref. No. 525 and 529 in page 60.
1.2 2016.09 Add three SCREW +BVTP 3X8 TYPE2 IT-3 in page 20 and 56.
Change description of Ref. No. 515 in page 60.
Change illustration for Ref. No. 407 in page 58.
Change of IC2005 to IC1008 in page 33.
Change P/N and illustration of Ref. No. 57 in page 51.
Change screw type from SCREW +BVTP 3X8 TYPE2 IT-3 to SCREW +BVTP 3X10 TYPE2 IT-3
for Ref. No. 407 in page 58.
Deletion of Thai model.
Delete note for IC001, IC009, IC109, IC301 and IC302 in page 36.

i
Delete note for IC105, IC106, IC303 and IC902 in page 37.
Delete note for IC1008 and IC1010 in page 38.
m
Delete P/N and description for AC INLET in page 59 and 63.
jo

How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.

e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.