Scribd
Upload
6 views

Tugas 6

The document provides detailed instructions for configuring a dynamic router using RIP (Routing Information Protocol) across multiple interfaces with specific IP addresses and subnet masks. It includes commands for enabling interfaces, assigning IP addresses, and verifying the status of the connections. The conclusion states that all PCs can communicate effectively due to the dynamic routing management by RIP, with no encountered issues during the practical implementation.

Uploaded by

Pain Akatsuki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
6 views

Tugas 6

The document provides detailed instructions for configuring a dynamic router using RIP (Routing Information Protocol) across multiple interfaces with specific IP addresses and subnet masks. It includes commands for enabling interfaces, assigning IP addresses, and verifying the status of the connections. The conclusion states that all PCs can communicate effectively due to the dynamic routing management by RIP, with no encountered issues during the practical implementation.

Uploaded by

Pain Akatsuki
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 30

Nama :

Kelas :
WORKSHEETCONFIGURATIONROUTERDINAMIS

Page 1 Configuration Inter VLAN

KONFIGURASI router Tengah Router>ena Router#conf t


Enter configuration commands, one per line. End with CNTL/Z.
ROUTER
Router(config)#int fa0/0
DINAMIS Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(configif)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.1.1 Router(config -router)#ex
Router(config)#int fa0/1
%Invalid interface type and number Router(config)#int fa0/0
Router(config-if)#ex Router(config)#int fa1/0
Router(config-if)#int add 192.168.2.1 255.255.0
^
% Invalid input detected at '^' marker.

Router(config-if)#ip add 192.168.2.1 255.255.255.0 Router(config-


if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

Router(config-if)#ex Router(config)#int fa2/0


Router(config-if)#ip add 192.168.3.1 255.255.255.0 Router(config-
if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

Router(config-if)#ex Router(config)#int fa3/0


Router(config-if)#ip add 192.168.4.1 255.255.255.0 Router(config-
if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.2.1
Router(config-

Page2 ConfigurationRouterDinamis router)#netw 192.168.3.1


Router(config-router)#netw 192.168.4.1 Router(config-router)#ex
Router(config)#

kiri atas Router>ena Router#conf t


Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa1/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.1.2 Router(config-router)#ex
Router(config)#int fa2/0
Router(config-if)#ip add 192.168.20.1 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.20.1 Router(config-router)#ex
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

Router(config)#int fa0/0
Router(config-if)#ip add 192.168.10.1 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.10.1 Router(config-router)#ex

Page3 ConfigurationRouterDinamis
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config)#int fa3/0
Router(config-if)#ip add 192.168.100.1 %
Incomplete command.
Router(config-if)#ip add 192.168.100.1 255.255.255.0 Router(config-if)#no shut

Page4 ConfigurationRouterDinamis
kanan atas

Router>ena Router#conf t
Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa1/0
Router(config-
Router(config-if)#ip add 192.168.3.2 255.255.255.0 Router(config-if)#not shut

% Invalid input detected at '^' marker. Router(config-if)#no shut


Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.3.2 Router(config-router)#ex
Router(config)#int fa0/0

Page5 ConfigurationRouterDinamis
Router(config-

if)#ip add 192.168.10.2 %


Incomplete command.
Router(config-if)#ip add 192.168.10.2 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Page6 ConfigurationRouterDinamis
Router(config-if)#ex Router(config)#router rip
Router(config-router)#netw 192.168.40.1 Router(config-router)#ex
Router(config)#int
Router(config- fa3/0
Router(config-if)#ip add 192.168.300.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.300.1

% Invalid input detected at '^' marker.

Router(config-router)#ex Router(config)#int fa3/0


Router(config-if)#ip add 192.168.300.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config-if)#ip add 192.168.300.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config-if)#ip add 192.168.200.1 255.255.255.0 Router(config-if)#int fa3/0

if)#ip add 192.168.400.1 255.255.255.0


^
% Invalid input detected at '^' marker.

Router(config-if)#ip add 192.168.110.1 255.255.255.0 Router(config-if)#no shut

Router(config-if)#

Page7 ConfigurationRouterDinamis
Router(config-

%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.110.1 Router(config-router)#ex
Router(config)#

kanan bawah Router>ena Router#conf t


Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa1/0
Router(config-if)#ip add 192.168.4.2 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.4.2 Router(config-router)#ex
Router(config)#int fa0/2
%Invalid interface type and number Router(config)#int fa2/0
Router(config-if)#ip add 192.168.40.2 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.40.2 Router(config-router)#ex
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.30.1 255.255.255.0 Router(config-if)#no shut

Page8 ConfigurationRouterDinamis
Router(config-

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.30.1 Router(config-router)#ex
Router(config)#int fa3/0
Router(config-if)#ip add 192.168.120.1 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.120.1 Router(config-router)#ex
Router(config)#

kiri bawah

Router>ena Router#conf t
Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int fa1/0
Router(config-if)#ip add 192.168.2.2 255.255.255.0 Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.2.2

router)#ex Router(config)#int fa2/0 Router(config-


if)#ip add 192.168.20.2 255.255.255.0
Router(config-if)#no shut

SUMBER TUJUAN HASIL


192.168.13.10 192.168.11.10 BERHASIL
192.168.12.10 192.168.13.10 BERHASIL
192.168.13.15 192.168.12.10 BERHASIL
192.168.14.18 192.168.13.10 BERHASIL
192.168.11.11 192.168.12.14 BERHASIL

Page9 ConfigurationRouterDinamis
Router(config-

%LINK-5-CHANGED: Interface FastEthernet2/0, changed


state to up

%LINEPROTO -5-UPDOWN: Line protocol on Interface


FastEthernet2/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.20.2 Router(config -
router)#ex
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.30.2 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed
state to up

%LINEPROTO -5-UPDOWN: Line protocol on Interface


FastEthernet0/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.30.2 Router(config -
router)#ex
Router(config)#int fa3/0
Router(config-if)#ip add 192.168.130.1 255.255.255.0 PENGUJIAN KONEKTIFITAS
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed
state to up

%LINEPROTO -5-UPDOWN: Line protocol on Interface


FastEthernet3/0, changed state to up

Router(config-if)#ex Router(config)#router rip


Router(config-router)#netw 192.168.130.1

Router(config-if)#

Page10 ConfigurationRouterDinamis
Router(config-

Page11 ConfigurationRouterDinamis
KESIMPULAN Setiap PC dapat saling berkomunikasi dan mengirim data dengan efektif berkat
penggunaan router dinamis RIP yang mengelola jalur routing secara otomatis

KENDALA SAAT
PRAKTIKUM Tidak Ada

PENYELESAIAN Tidak Ada


KENDALA SAAT
PRAKTIKUM

LAMPIRAN
Konfigurasi Router

Router Tengah
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#

Page12 ConfigurationRouterDinamis
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up Router(config-if)#ex
Router(config)#router rip
Router(config-router)#netw 192.168.1.1
Router(config-router)#ex
Router(config)#int fa0/1
%Invalid interface type and number

Router(config-if)#ex
Router(config)#int fa1/0
Router(config-if)#int add 192.168.2.1 255.255.0

% Invalid input detected at '^' marker.

Router(config-if)#ip add 192.168.2.1 255.255.255.0


Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

Router(config-if)#ex
Router(config)#int fa2/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

Router(config-if)#ex
Router(config)#int fa3/0
Router(config-if)#ip add 192.168.4.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

Router(config-if)#ex
Router(config)#router rip
Router(config-router)#netw 192.168.2.1
Router(config-router)#netw 192.168.3.1
Router(config-router)#netw 192.168.4.1
Router(config)#int fa0/0

Page13 ConfigurationRouterDinamis
Router(config-router)#ex
Router(config)#

Router Kiri Atas


Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.

Page14 ConfigurationRouterDinamis
Router(config)#int fa1/0
Router(config
-if)#ip add 192.168.1.2 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.1.2
Router(config
-router)#ex
Router(config)#int fa2/0
Router(config
-if)#ip add 192.168.20.1 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.20.1
Router(config
-router)#ex
Router(config)#
%LINEPROTO -5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

Router(config)#int fa0/0
Router(config
-if)#ip add 192.168.10.1 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#router rip
Router(config-router)#netw 192.168.10.1
Router(config-router)#ex Router(config)#

Page15 ConfigurationRouterDinamis
Page16 ConfigurationRouterDinamis
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa1/0
Router(config
-if)#ip add 192.168.3.2 255.255.255.0
Router(config
-if)#not shut

% Invalid input detected at '^' marker.

Router(config
-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Page17 ConfigurationRouterDinamis
Router(config
-router)#netw 192.168.40.1
Router(config
-router)#ex
Router(config)#int fa3/0
Router(config
-if)#ip add 192.168.300.1 255.255.255.0

^
% Invalid input detected at '^' marker.

Router(config-if)#ex
Router(config)#router rip
Router(config-router)#netw 192.168.300.1
^
% Invalid input detected at '^' marker.

Page18 ConfigurationRouterDinamis
Router(config
-router)#ex
Router(config)#int fa3/0
Router(config
-if)#ip add 192.168.300.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config
-if)#ip add 192.168.300.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config
-if)#ip add 192.168.200.1 255.255.255.0
Router(config
-if)#int fa3/0
Router(config
-if)#ip add 192.168.400.1 255.255.255.0

% Invalid input detected at '^' marker.

Router(config
-if)#ip add 192.168.110.1 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.110.1
Router(config
-router)#ex
Router(config)#

Router Kanan Bawah

Page19 ConfigurationRouterDinamis
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa1/0
Router(config-if)#ip add 192.168.4.2 255.255.255.0
Router(config-if)#no shut

Page20 ConfigurationRouterDinamis
Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.4.2
Router(config
-router)#ex
Router(config)#int fa0/2
%Invalid interface type and number
Router(config)#int fa2/0
Router(config
-if)#ip add 192.168.40.2 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.40.2
Router(config
-router)#ex
Router(config)#int fa0/0
Router(config
-if)#ip add 192.168.30.1 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config
-if)#ex

Router(config)#router rip
Router(config-router)#netw 192.168.30.1
Router(config-router)#ex
Router(config)#int fa3/0
Router(config-if)#ip add 192.168.120.1 255.255.255.0
Router(config-if)#no shut

Page21 ConfigurationRouterDinamis
Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.120.1
Router(config
-router)#ex
Router(config)#

Router Kiri Bawah


Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa1/0
Router(config
-if)#ip add 192.168.2.2 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.2.2
Router(config
-router)#ex
Router(config)#int fa2/0
Router(config
-if)#ip add 192.168.20.2 255.255.255.0
Router(config
-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

Page22 ConfigurationRouterDinamis
Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.20.2
Router(config
-router)#ex
Router(config)#int fa0/0
Router(config
-if)#ip add 192.168.30.2 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.30.2
Router(config
-router)#ex
Router(config)#int fa3/0
Router(config
-if)#ip add 192.168.130.1 255.255.255.0
Router(config
-if)#no shut

Router(config
-if)#
%LINK-5-CHANGED: Interface FastEthernet3/0, changed state to up

%LINEPROTO
-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state to up

Router(config
-if)#ex
Router(config)#router rip
Router(config
-router)#netw 192.168.130.1

Konfigurasi/pemasangan IP Address di-masing client

PC 1

Page23 ConfigurationRouterDinamis
PC 2

Page24 ConfigurationRouterDinamis
PC 3

Page25 ConfigurationRouterDinamis
PC 4

PC 5

Page26 ConfigurationRouterDinamis
PC 6

PC 7

Page27 ConfigurationRouterDinamis
PC 8

Hasil pengujian konektifitas (sesuai table pengujian konektifitas) Sumber : 192.168.13.10


Tujuan : 192.168.11.10

Sumber : 192.168.12.10
Tujuan : 192.168.13.10

Page28 ConfigurationRouterDinamis
Sumber : 192.168.13.15
Tujuan : 192.168.12.10

Sumber : 192.168.14.18
Tujuan : 192.168.13.10

Page29 ConfigurationRouterDinamis
Sumber : 192.168.11.11
Tujuan : 192.168.12.14

Page30 ConfigurationRouterDinamis

You might also like