STBC03

Datasheet

Li-Ion linear battery charger with LDO and load switches

Features
• Charges single-cell Li-Ion batteries with CC/CV algorithm and charge
termination
• Fast charge current up to 650 mA adjustable by external resistor
• Pre-charge current from 1 mA
• Adjustable floating voltage up to 4.45 V
• Integrated low quiescent LDO regulator
• Automatic power path management
• Auto-recharge function
• Embedded protection circuit module (PCM) featuring battery overcharge, battery
Maturity status link over-discharge and battery overcurrent protections
• Charging timeout
STBC03
• Shipping mode feature allows battery low leakage when over-discharged
• Very low battery leakage in over-discharge and shutdown mode
Device summary • Charger enable input
Order code STBC03JR • Charge/fault status output
LDO 3.0 V • Battery voltage pin to allow external gauging
• Two 3 Ω SPDT load switches
Package 400 µm pitch
• Available in Flip Chip 30, 400 µm pitch package
• Rugged ±4 kV HBM, ESD protection on the most critical pins

Applications
• Smart watches and wearable devices
• Fitness and medical accessories
• Li-Ion and other Li-Poly battery rechargeable equipment

Description
The STBC03 is a highly integrated power management, embedding a linear battery
charger, a 150 mA LDO, 2 SPDT load switches, and a protection circuit module
(PCM) to prevent the battery from being damaged under fault conditions.
The STBC03 uses a CC/CV algorithm to charge the battery; the fast charge and
the pre-charge current can be both independently programmed using dedicated
resistors. The termination current is set to 5% of the programmed fast charge current,
but has fixed values for fast charge currents lower than 20 mA. The battery floating
voltage value is programmable and can be set to a value up to 4.45 V.
The STBC03 also features a charger enable input to stop the charging process
anytime.
The STBC03 is automatically powered off from the connected battery when the IN pin
is not connected to a valid power source (battery mode).
A battery under/overtemperature condition can be detected by using an external
circuitry (NTC thermistor).
The STBC03 draws less than 10 nA from the connected battery in shipping mode
conditions, so to maximize the battery life during shelf life of the final application. The
device is available in the Flip Chip 30 package.

DS11889 - Rev 6 - March 2022 www.st.com

For further information contact your local STMicroelectronics sales office.
 STBC03
Application schematic

1 Application schematic

Figure 1. STBC03 application schematic

Table 1. Typical bill of material (BOM)

Symbol Value Description Note

CIN 10 µF (16 V) Input supply voltage capacitor Ceramic type

CSYS 1 µF (10 V) System output capacitor Ceramic type

RISET Refer to ISET Charge current programming resistor Film type

RIPRE Refer to IPRE Pre-charge current programming resistor Film type

CBAT 4.7 µF (6.3 V) Battery positive terminal capacitor Ceramic type

RFLOAT BATSNSFV Floating voltage programming resistor Film type

RDIV1, DIV2 100-200 kΩ Battery monitor resistor divider Film type

RCHG 10 kΩ Charging/fault pull-up resistor(1) Film type

CLDO 1.0 µF (10 V) LDO output capacitor Ceramic type

1. RCHG must be calculated according to the external LED electrical characteristics.

DS11889 - Rev 6 page 2/31

 STBC03
Pin configuration

2 Pin configuration

Figure 2. Pin configuration top through view

Table 2. Pin description

Bump
Bump Description
name

IN E5-F5 Input supply voltage. Bypass this pin to ground with a 10 µF capacitor
BAT A5-B5 Battery positive terminal. Bypass this pin to GND with a 4.7 µF ceramic capacitor
SYS C5-D5 System output. Bypass this pin to ground with 1 µF ceramic capacitor
Power LDO F4 LDO output. Bypass this pin to ground with 1 µF ceramic capacitor
NTC D1 Battery temperature monitor pin
AGND B4 Analog ground
Connect together with the same ground layer
GND A3 GROUND
ISET A4 Fast charge current programming resistor
Programming
IPRE D4 Pre-charge current programming resistor
BATMS C4 Battery voltage measurement pin
Sensing BATSNS B3 Battery voltage sensing. Connect as close as possible to the battery positive terminal
BATSNSFV A2 Floating voltage sensing. Connect as close as possible to the battery positive terminal
CEN B1 Charger enable pin. Active high. 500 kΩ internal pull-up (to LDO)
CHG E1 Charging/fault flag. Active low (open drain output)
WAKE-UP D2 Shipping mode exit input pin. Active high. 50 kΩ internal pull-down
SW_SEL2 C1 Load switch 2 selection input (refer to LDO level)
Digital I/Os
BATMS_EN C2 Battery monitor enable input (refer to LDO level)
SW_SEL1 B2 Load switch 1 selection input (refer to LDO level)
Shutdown input signal (refer to LDO level). When low, the STBC03 exits ship mode. It
SD A1
cannot be left floating
Load switch SPDT1 input (1.8 V
SW1_I F3
to 5 V range)
If SPDT switches are used, decoupling capacitors
SW1_OA E4 Load switch SPDT1 output A are recommended on input and output. Capacitor
Switch matrix values depend on application conditions and
SW1_OB E3 Load switch SPDT1 output B requirements.
Load switch SPDT2 input (1.8 V If not used, connect inputs and outputs to GND
SW2_I E2
to 5 V range)

DS11889 - Rev 6 page 3/31

 STBC03
Pin configuration

Bump
Bump Description
name

SW2_OA F2 Load switch SPDT2 output A If SPDT switches are used, decoupling capacitors
are recommended on input and output. Capacitor
Switch matrix values depend on application conditions and
SW2_OB F1 Load switch SPDT2 output B requirements.
If not used, connect inputs and outputs to GND
NC C3-D3 Not connected Leave floating

DS11889 - Rev 6 page 4/31

 STBC03
Maximum ratings

3 Maximum ratings

Table 3. Absolute maximum ratings

Symbol Parameter Test conditions Value Unit

DC voltage -0.3 to +10.0 V

VIN Input supply voltage pin Non repetitive, 60 s pulse
-0.3 to +16.0 V
length
VLDO LDO output pin voltage DC voltage -0.3 to +4.0 V

VSYS SYS pin voltage DC voltage -0.3 to +6.5 V

Switch pin voltage (SW1_I, SW2_I, SW1_OA,

VSW DC voltage -0.3 to +6.5 V
SW1_OB, SW2_OA, SW2_OB)
VCHG CHG pin voltage DC voltage -0.3 to +6.5 V

VWake-up WAKE-UP pin voltage DC voltage -0.3 to +4.6 V

Voltage on logic pins (CEN, SW_SEL1,

VLGC DC voltage -0.3 to +4.0 V
SW_SEL2, SD,BATMS_EN)
VISET, VIPRE Voltage on ISET, IPRE pins DC voltage -0.3 to +2 V

VNTC Voltage on NTC pin DC voltage -0.3 to VLDO V

VBAT, VBATSNS,
Voltage on BAT, BATSNS and BATSNSFV pins DC voltage -0.3 to +5.5 V
VBATSNSFV

VBATMS Voltage on BATMS pin DC voltage -0.3 to VBAT+0.3 V

Human body model (IN, SYS, WAKE-UP, LDO, JS-001-2012 vs. AGND
±4000 V
ESD BAT, BATSNS, BATSNSFV) PGND and GND
Human body model (all the others) JS-001-2012 ±2000 V
TAMB Operating ambient temperature -40 to +85 °C

TJ Maximum junction temperature +125 °C

TSTG Storage temperature -65 to +150 °C

Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional
operation under these conditions is not implied.

Table 4. Thermal data

Symbol Parameter Flip Chip 30 (2.25x2.59 mm) Unit

RTHJB (1) Junction-to-pcb board thermal resistance 50 °C/W

1. Standard FR4 pcb board.

DS11889 - Rev 6 page 5/31

 STBC03
Electrical characteristics

4 Electrical characteristics

VIN=5 V, VBAT = 3.6 V, CLDO = 1 µF, CBAT = 4.7 µF, CIN = 10 µF, CSYS = 1 µF, RISET = 1 kΩ, SD = GND, CEN =
high, RIPRE = 4.7 kΩ, TA = 25 °C, SW_SEL1 = SW_SEL2 = GND, BATMS_EN = GND, WAKE-UP floating unless
otherwise specified.

Table 5. Electrical characteristics

Symbol Parameter Test conditions Min. Typ. Max. Unit

VFLOAT set 4.2 V, IFAST < 250 mA 4.55 5.4 V

VIN Operating input voltage VFLOAT set 4.45 V, IFAST < 450 mA, ISYS = ILDO = 0
4.75 5.4 (1) V
mA
VINOVP Input overvoltage protection VIN rising 5.6 5.9 6.4 V

Input overvoltage protection

VINOVPH VIN falling 200 mV
hysteresis
VUVLO Undervoltage lock-out VIN falling 3.9 V

VUVLOH Undervoltage lock-out hysteresis VIN rising 300 mV

Charger disabled mode (CEN = low), ISYS = ILDO =

600 μA
0A
IIN IN supply current
Charging, VHOT < VNTC < VCOLD, including RISET
1.4 mA
current
IBAT = 1 mA, BATSNS and BATSNSFV short to
VFLOAT Battery floating voltage 4.179 4.2 4.221 V
battery terminal
Battery-powered mode (VIN < VUVLO), ILDO = 0 A 4 8 µA

Charge terminated 9 12 µA
IBAT BAT pin supply current
Shutdown mode (by SD pin) 10 50
nA
Over-discharge mode (VBAT < VODC, VIN < VUVLO) 10 50

RISET = 300 Ω 650(1)

RISET = 430 Ω, constant-current mode ILDO+ ISYS

IFAST Fast charge current 450(1) 500 mA
< 150 mA
RISET = 1 kΩ, constant-current mode 200

IPRE Pre-charge current RIPRE = 10 kΩ, constant-current mode 20 mA

VISET ISET regulated voltage 1 V

VIPRE IPRE regulated voltage 1 V

Pre-charge to fast charge battery

VPRE Charger active 3 V
voltage threshold
Charging in CV mode for 20 mA < IFAST 5 %IFAST
IEND End-of-charge current
Charging in CV mode for IFAST< 20 mA See Table 10. IFAST and IEND

VBAT rising, BATSNSFV short to battery terminal 4.245 4.275 4.305 V

Battery voltage overcharge
VOCHG VBAT rising, external resistor between BATSNSFV
threshold VFLOAT+75 mV
and battery terminal

Battery voltage over-discharge VIN < VUVLO, ILDO = 150 mA, BATSNSFV and
VODC 2.750 2.8 2.850 V
threshold BATSNS short to battery terminal

Battery voltage over-discharge VUVLO < VIN < VOVP, ILDO = 150 mA, BATSNSFV
VODCR 3.0 V
release threshold and BATSNS short to battery terminal
VWAKE-UP Wake-up voltage threshold VBAT>3 V rising, ILDO = 150 mA 2.2 V

DS11889 - Rev 6 page 6/31

 STBC03
Electrical characteristics

Symbol Parameter Test conditions Min. Typ. Max. Unit

RON-IS Input to SYS on-resistance 0.25 0.35 Ω

RON-BS Battery to SYS on-resistance 0.35 0.4 Ω

RON-BATMS BATSNS to BATMS on-resistance ISINK = 500 µA 290 550 Ω

Input to output load switch 1 VSW1_I = 1.8 V to 5 V SW1_OA or SW1_OB test

RON-LOADSW1 2.0 3.8 Ω
resistance current = 50 mA

Input to output load switch 2 VSW2_I = 1.8 V to 5 V

RON-LOADSW2 2.0 3.4 Ω
resistance SW2_OA or SW2_OB test current = 50 mA
VOL Output low level (CHG) ISINK = 5 mA 0.4 V

High level open drain output

IOHZ VOH = 5 V 1 μA
current (CHG)
Logic low input level
VIL (CEN, SW_SEL1, SW_SEL2, 0.4 V
BATMS_EN, SD)
Logic high input level
VIH (CEN, SW_SEL1, SW_SEL2, 1.6 V
BATMS_EN, SD)
RUP CEN pull-up resistor 375 500 625 kΩ

VLDO LDO output voltage ILDO = 1 mA 2.9 3.0 3.1 V

ΔVOUT-LOAD LDO static load regulation ILDO = 1 mA to 150 mA ±0.002 ±0.003 %/mA

ISC LDO short-circuit current RLOAD = 0 Ω 250 350 mA

tON LDO turn-on time 0 to 95% VLDO, IOUT = 150 mA 210 µs

Battery discharge overcurrent

IBATOCP VIN<VUVLO (powered from BAT) 900 mA
protection
VSYS> VILIMSCTH; VUVLO < VIN < VINOVP (powered
IINLIM Input current limitation 1.7 A
from IN)
SYS voltage threshold for input
VILIMSCTH current limitation short-circuit VUVLO < VIN < VINOVP 2 V
detection
SYS short-circuit protection
VSCSYS VIN < VUVLO or VIN>VINOVP (powered from BAT) VBAT-0.8 V
threshold
INTCB NTC pin bias current VNTC = 0.25 V 45 50 55 µA

VHOT Thermal hot threshold Increasing NTC temperature 0.234 0.246 0.258 V

VCOLD Thermal cold threshold Decreasing NTC temperature 1.28 1.355 1.43 V

Hot/cold temperature thresholds

THYST 10 kΩ NTC, ß = 3370 3 °C
hysteresis
TSD Thermal shutdown die temperature 155 °C

TWRN Thermal warning die temperature 135 °C

Minimum input voltage connection

tPW-VIN VBAT = 3.5 V, RNTC = 10 kΩ 350 ms
time to exit from shutdown mode
tOCD Overcharge detection delay VBAT> VOCHG, VUVLO<VIN<VINOVP 1.2 s

tODD Over-discharge detection delay VBAT < VODC and VIN < VUVLO or VIN> VINOVP 60 ms

Discharge overcurrent detection

tDOD IBAT> IBATOCP, VIN<VUVLO or VIN> VINOVP 10 ms
delay
Pre-charge to fast charge transition
tPFD Rising 100 ms
deglitch time

DS11889 - Rev 6 page 7/31

 STBC03
Electrical characteristics

Symbol Parameter Test conditions Min. Typ. Max. Unit

Fast charge to pre-charge fault

tFPD 10 ms
deglitch time
tEND End-of-charge deglitch time 100 ms

tPRE Pre-charge timeout VBAT = 2 V, charging 1800 s

tFAST Fast charge timeout 14000 18000 22000 s

tCRDD Charger restart deglitch time After end-of-charge, VBAT < 3.9 V restart enabled 1200 ms

VREC Charger restart threshold After end-of-charge, restart enabled 3.9 V

Battery temperature transition

tNTCD 100 ms
deglitch time
tPW CEN valid input pulse width 15 ms

tPW-WA WAKE-UP valid input pulse width 1200 ms

1. If the internal thermal temperature of the STBC03 reaches TWRN, then the programmed IFAST is halved until the internal temperature drops
below TWRN - 10 °C typically. A warning is signaled via the CHG output.

DS11889 - Rev 6 page 8/31

 STBC03
Typical performance characteristics

5 Typical performance characteristics

Figure 3. Battery mode 3 V LDO load transient response Figure 4. Thermal management

VBAT = 3.7 V, 10 mA to 150 mA, slope 150 mA/1 µs VBAT = 3.7 V, VIN = 5.0 V

CH1 (blue) = VIN

CH2 (red) = LDO 1 V/div
CH2 (red) = LDO
CH3 (green) = LDO 10 mV/div
CH3 (green) = CHG
CH4 (pink) = LDO load variation
CH4 (pink) = IBAT

Figure 6. Pre-charge to fast charge mode transition

Figure 5. VIN mode, overvoltage protection
threshold

Charging is resumed when OVP disappears

CH1 (blue) = VIN 800 mV/div
CH1 (blue) = VIN 800 mV/div
CH2 (red) = VSYS 800 mV/div
CH2 (red) = VSYS 800 mV/div
CH3 (green) = VBAT 800 mV/div
CH3 (green) = VBAT 800 mV/div
CH4 (pink) = IBAT 20 mA/div
CH4 (pink) = IBAT 20 mA/div

DS11889 - Rev 6 page 9/31

 STBC03
Typical performance characteristics

Figure 7. Pre-charge to fast charge mode transition Figure 8. Pre-charge to fast charge mode to no charge
deglitch mode transition

CH1 (blue) = VIN 800 mV/div CH1 (blue) = VIN 800 mV/div
CH2 (red) = VSYS 800 mV/div CH2 (red) = VSYS 800 mV/div
CH3 (green) = VBAT 800 mV/div CH3 (green) = VBAT 800 mV/div
CH4 (pink) = IBAT 20 mA/div CH4 (pink) = IBAT 20 mA/div

Figure 10. VIN plug, charging initialization

Figure 9. Wake-up pin operation

Shutdown mode to battery mode transition. VIN floating Shutdown mode to VIN mode transition

CH1 (blue) = VIN 800 mV/div

CH1 (blue) = WAKE-UP pin 800 mV/div
CH2 (red) = VSYS 800 mV/div
CH2 (red) = VSYS 800 mV/div
CH3 (green) = VBAT 800 mV/div
CH3 (green) = VBAT 800 mV/div
CH4 (pink) = IBAT 20 mA/div

DS11889 - Rev 6 page 10/31

 STBC03
Typical performance characteristics

Figure 11. Wake-up operation, VSYS and LDO rise

Figure 12. Wake-up operation, VSYS and LDO rise detail
overview

CH1 (blue) = VLDO 800 mV/div CH1 (blue) = VLDO 800 mV/div
CH2 (red) = VSYS 800 mV/div CH2 (red) = VSYS 800 mV/div
CH3 (green) = VBAT 800 mV/div CH3 (green) = VBAT 800 mV/div
CH4 (pink) = Wake-up 3 V/div CH4 (pink) = Wake-up 3 V/div

Figure 13. VIN plug, charging initialization battery mode to

VIN mode transition Figure 14. Shutdown mode entry

CH1 (blue) = VIN 800 mV/div By SD pin

CH2 (red) = VSYS 800 mV/div
CH1 (blue) = SD pin, 1 V/div
CH3 (green) = VBAT 800 mV/div
CH2 (red) = SYS pin, 1 V/div
CH4 (pink) = IBAT 20 mA/div

DS11889 - Rev 6 page 11/31

 STBC03
Typical performance characteristics

Figure 15. VBAT to VSYS drop and VSYS to VLDO drop Figure 16. VBAT to VSYS drop and VSYS to VLDO drop
(10 mA) (100 mA)

LDO loaded by 10 mA; VODC cut-off LDO loaded by 100 mA; VODC cut-off

CH1 (blue) = VLDO 400 mV/div CH1 (blue) = VLDO 400 mV/div
CH2 (red) = VSYS 400 mV/div CH2 (red) = VSYS 400 mV/div
CH3 (green) = VBAT 400 mV/div CH3 (green) = VBAT 400 mV/div
CH4 (pink) = ILDO 10 mA/div CH4 (pink) = ILDO 20 mA/div

Figure 17. CEN operation Figure 18. CEN operation, VIN plug/unplug

CH1 (blue) = CEN 3 V/div CH1 (blue) = IN pin 3.0 V/div

CH3 (green) = VBAT 800 mV/div CH3 (green) = CEN 2.0 V/div

CH4 (pink) = IBAT 20 mA/div CH4 (pink) = IBAT 30 mA/div

DS11889 - Rev 6 page 12/31

 STBC03
Functional pin description

6 Functional pin description

6.1 GND, AGND

The STBC03 ground pins.

6.2 NTC
The battery temperature monitoring pin. Connect the battery NTC thermistor to this pin. The charging cycle stops
when the battery temperature is outside of the safe temperature range (0 °C to 45 °C). When the charging cycle is
completed, the NTC pin goes to a high impedance state, therefore the NTC thermistor can be also used, together
with an external circuitry, to monitor the battery temperature while it is being discharged. If the NTC thermistor is
not used, a 10 kΩ resistor must be connected to ensure proper IC operations.

6.3 ISET, IPRE

Fast and pre-charge current programming pins. Connect two resistors (RISET, RIPRE) to ground to set the fast and
pre-charge current (IFAST, IPRE) according to the following equation (valid for IFAST, IPRE > 5 mA):
Equation 1:
V V
IPRE = IPRE *K ; I = RISET *K (1)
RIPRE FAST ISET
Where VISET = VIPRE = 1 V and K = 200. Fast charge and pre-charge currents can be independently set from 1
mA to 650 mA. End-of-charge current value is typically 5% of the fast charging current value being set.
For low charging current (IFAST, IPRE < 5 mA), the RISET and RIPRE values in the following table must be used.

Table 6. Charging current setting

IFAST, IPRE RISET, RIPRE

5 mA 40.5 k
2 mA 110 k
1 mA 260 k

Both RISET and RIPRE must be always used. Short-circuit to ground or open circuit are not allowed options.

6.4 BATMS, BATMS_EN

Battery voltage measurement. If BATMS_EN is high, the BATMS pin is internally shorted to the BATSNS pin
during normal conditions to monitor the battery voltage using external components (µC and embedded ADC).
The internal path from BATMS pin to the battery is opened in case any of the following conditions occur:
overcurrent, battery over-discharge, shutdown mode, short-circuit on SYS or LDO. To minimize overall system
power consumption, this function must be disabled. BATMS_EN pin should be pulled low.

6.5 BATSNS, BATSNSFV

Battery voltage sense pin. The BATSNS pin must be connected as close as possible to the battery positive
terminal to ensure the maximum accuracy on the floating voltage and on the battery voltage protection thresholds.
The BATSNSFV pin can be used to fix the VFLOAT value by connecting a proper external series resistor to
BATSNSFV. The battery floating voltage can be set up to 4.45 V according to the following equation:
Equation 2:
Rfloat Rfloat
Vfloatadj = Vfloatdef * 1 + 1MΩ V = 4.2* 1 + 1MΩ V (2)

Example: to set the battery floating voltage for 4.35 V, refer to the following equation.
Equation 3:
Vfloatadj 4.35V
Rext = 1MΩ * − 1 = 1MΩ* 4.2V − 1 = 35.7KΩ (3)
4.2V

DS11889 - Rev 6 page 13/31

 STBC03
BAT

If the BATSNSFV pin is connected to the battery positive terminal, the floating voltage is set for its 4.2 V default
value.

6.6 BAT
External battery connection pin (positive terminal). A 4.7 µF ceramic bypass capacitor must be connected to
GND.

6.7 IN
5 V input supply voltage pin. The STBC03 is powered off from this pin when a valid voltage source is detected,
meaning a voltage higher than VUVLO and lower than VINOVP. A 10 µF ceramic bypass capacitor must be
connected to GND.

6.8 SYS
The internal LDO input voltage and external unregulated supply pin. The maximum current deliverable through
this pin depends on the following two conditions: LDO load and battery status. However, if none of the above
loads sinks current, the maximum SYS current budget is 650 mA, provided that the input voltage source can
deliver that amount of current.
SYS voltage source can be either IN or BAT, depending on the operating conditions (refer to the following table).
A ceramic bypass capacitor of 1 µF must be connected to GND.

Table 7. SYS voltage source

VIN VBAT SYS status LDO status

< VUVLO < VODC (1)

Not powered Off

< VUVLO > VODC VBAT On

> < VUVLO and < VINOVP X (don’t care)(3) VIN On

> VINOVP < VODC Not powered Off

> VINOVP > VODC VBAT On

1. VODCR if the shutdown mode or the over-discharge protection has been previously activated.
2. Voltage drop over internal MOSFET is not included.
3. Battery disconnected (0 V) or fully discharged. Resistive short-circuit is not supported for safety reasons.

6.9 LDO
LDO output voltage pin. The maximum current capability is anyhow 150 mA. A 1 µF ceramic bypass capacitor
must be connected to GND.

6.10 WAKE-UP
Wake-up input pin. To restore normal operations of the STBC03, so to exit from a shutdown condition, connect
the WAKE-UP pin to the battery voltage. The STBC03 is enabled to operate in normal conditions again, only if the
battery voltage is higher than VODCR (3 V). A deglitch delay is implemented to prevent unwanted false operations.
The above-described WAKE-UP pin functionality is disabled when a valid VIN voltage source is detected. The pin
has an internal 50 kΩ pull-down resistor.

DS11889 - Rev 6 page 14/31

 STBC03
CHG

6.11 CHG
Active low, open drain charging/fault flag output pin. The CHG provides status information about VIN voltage
level, battery charging and faults by toggling at different frequencies as reported in the table below.

Table 8. CHG pin state

Device state CHG pin state Note

Not valid input (VIN <

High Z (high by
VBAT or VIN > VINOVP
external pull-up)
or VIN < VINUVLO)

Valid input (VIN

>VINUVLO, VIN <
Low
VINOVP, VBAT < VIN
and CEN low)
Toggling 4.1 Hz
End-of-charge
(EOC) (until USB is
disconnected)
In case of synchronous alarm events, the highest toggling frequency has higher
Charging phase (pre priority.
Toggling 6.2 Hz
and fast) Example: NTC warning and EOC are concurrent events. NTC warning, signaled
Overcharge fault Toggling 8.2 Hz by toggling CHG at 16.2 Hz is the only signal available till the battery temperature
goes back to a safe range (0 °C to 45 °C). If an EOC condition is still present then
Charging timeout a 4.1 Hz toggling signal is present.
(pre-charge, fast Toggling 10.2 Hz
charge)
Battery voltage
below VPRE after the Toggling 12.8 Hz
fast charge starts
Charging thermal
limitation (thermal Toggling 14.2 Hz
warning)
Battery temperature
Toggling 16.2 Hz
fault (NTC warning)

6.12 CEN
Internal CC/CV charger block enable pin. A low logic level on this pin disables the internal CC/CV charger block.
Transitioning CEN from high to low and then back to high, allows the CC/CV charger block to be restarted if it was
stopped due to one of the following conditions:
• Charging timeout (pre-charge, fast charge)
• Battery voltage below VPRE after the fast charge has already started
• End-of-charge
CEN has no effect if the charging cycle has been stopped by a battery overcharge condition.
If the CC/CV charger stops the charging cycle due to an out of range battery temperature, a low logic level on
the CEN pin disables the CC/CV charger and resets the charging timeout timers. If CEN is set high, the CC/CV
charger restarts normal operations, assuming that no fault condition is detected. CEN is internally pulled up to
LDO via a 500 kΩ resistor and must be either left floating or tied to LDO when the STBC03 is powered for the first
time.
The auto-recharge function is always enabled so, the CC/CV charger restarts automatically charging the battery if
VBAT goes below 3.9 V; a deglitch time delay has been added to prevent unwanted charging cycle from restarting.

6.13 SD
The shutdown pin. In battery mode (if no valid VBUS voltage is present) a logic high level on this pin asserts the
low power consumption mode. If SD is kept high when a pulse is applied to WAKE-UP pin the device exits the
shutdown condition for the duration of the WAKE-UP pulse. In shutdown mode, the battery drain is then reduced
to less than 50 nA. If a valid VBUS voltage is present, the SD pin status has no effect and the device is always out
of the shutdown condition.

DS11889 - Rev 6 page 15/31

 STBC03
SW1_OA, SW1_OB, SW1_I, SW2_OA, SW2_OB, SW2_I

6.14 SW1_OA, SW1_OB, SW1_I, SW2_OA, SW2_OB, SW2_I

SPDT load switch pins. Both of SPDT load switches are controlled by the digital control pins (see section below).
Each SPDT features a typical RDS(on) of 3 Ω. SPDT load switches can be paralleled to reduce the series resistor
as well as to increase the allowable flowing current.

6.15 SW_SEL1 and SW_SEL2

SW_SEL1 and SW_SEL2 drive the SPDT switches according to the following table. They should be connected to
GND if not used.

Table 9. SW_SEL1, SW_SEL2 operation

INPUTS OUTPUTS

SW_SEL 1 SW_SEL2 SW1_OA SW1_OB SW2_OA SW2_OB

0 0 SW1_I Hi-Z SW2_I Hi-Z

1 0 Hi-Z SW1_I SW2_I Hi-Z
0 1 SW1_I Hi-Z Hi-Z SW2_I
1 1 Hi-Z SW1_I Hi-Z SW2_I

DS11889 - Rev 6 page 16/31

 STBC03
Block diagram

7 Block diagram

Figure 19. STBC03 block diagram

DS11889 - Rev 6 page 17/31

 STBC03
Operation description

8 Operation description

The STBC03 is a power management IC integrating a battery charger with an embedded power path function, a
150 mA low quiescent LDO, two SPDT load switches and a protection circuit module (PCM) to prevent the battery
from being damaged.
When powered off from a single-cell Li-Ion or Li-Poly battery, and after having performed all the safety checks, the
STBC03 starts charging the battery using a constant-current and constant-voltage algorithm.
The embedded power path allows simultaneously the battery to be charged and the overall system to be supplied.
By contrast, when the input voltage is above the valid range, the battery supplies the LDO as well as every load
connected to SYS.
The STBC03 also protects the battery in case of:
• Overcharge
• Over-discharge
• Charge overcurrent
• Discharge overcurrent
If a fault condition is detected when the input voltage is valid (VUVLO < VIN < VINOVP), the CHG pin starts toggling,
signaling the fault.
The device can also be in shutdown mode (shutdown IBAT < 50 nA) maximizing the battery life of the end-product
during its shelf life.

8.1 Power-on
When the STBC03 is in shutdown mode, any load connected to LDO and to SYS is not supplied.
An applied valid input voltage (VUVLO < VIN < VINOVP) for at least 250 ms, regardless the presence of a battery or
if the battery is fully depleted, allows the loads connected to SYS and LDO to be supplied, thus enabling proper
system operations.
The CEN pin must be left floating or tied high (LDO level) during the power-on for proper operations. The STBC03
can be also turned on when VIN is outside the valid range, below the conditions that the battery has at least a
remaining charge of 3 V and the wake-up input is properly triggered. The STBC03 features an UVLO circuit that
prevents oscillations if the input voltage source is unstable. The CEN pin must be left floating or tied to a high
level (LDO) when the STBC03 is powered.

8.2 Battery charger

The STBC03 allows single-cell Li-Ion and Li-Poly battery chemistry to be charged up to a 4.45 V using a CC/CV
charging algorithm. The charging cycle starts when a valid input voltage source (VUVLO < VIN < VINOVP) is
detected and signaled by the CHG pin toggling from a high impedance state to a low logic level.
If the battery is deeply discharged (the battery voltage is lower than VPRE), the STBC03 charger enters the
pre-charge phase and starts charging in constant-current mode with the pre-charge current (IPRE) set. In case the
battery voltage does not reach the VPRE threshold within the tPRE time, the charging process is stopped and a
fault is signaled.
By contrast, as soon as the battery voltage reaches the VPRE threshold, the constant-current fast charge phase
starts operating, and the relevant charging current increases to the IFAST level.
Likewise, if the constant current fast charge phase is not completed within tFAST, meaning that VBAT < VFLOAT,
the charging process is stopped and a fault is signaled (CHG starts toggling at 10.2 Hz as long as a valid VIN is
present).
Should the battery voltage decrease below VPRE during the fast charge phase, the charging process is halted and
a fault is signaled. The constant-current fast charge phase lasts until the battery voltage is lower than VFLOAT.
After that, the charging algorithm switches to a constant-voltage (CV) mode.
During the CV mode, the battery voltage is regulated to VFLOAT and the charging current starts decreasing over
time. As soon as it goes below IEND, the charging process is considered to be completed (EOC, end-of-charge )
and the relevant status is signaled via a 4.1 Hz toggling signal on the CHG pin, again as long as a there is a valid
input source applied (VUVLO < VIN < VINOVP).
Both IPRE and the IFAST values can be programmed from 1 mA to 450 mA via an external resistor, as described in
the ISET pin description.

DS11889 - Rev 6 page 18/31

 STBC03
Battery charger

For any IFAST programmed value above 20 mA, the IEND value can be set either 5% or 2.5% of the IFAST level.
For any IFAST programmed value below 20 mA, the relevant IEND value is set as per the following table:

Table 10. IFAST and IEND

IFAST IEND

20 mA 1.7 mA
10 mA 1.1 mA
5 mA 0.65 mA
2 mA 0.4 mA
1 mA 0.2 mA

The battery temperature is monitored throughout the charging cycle for safety reasons.

Figure 20. Charging flowchart

DS11889 - Rev 6 page 19/31

 STBC03
Battery charger

Actions:
• Pre-charge starts tPRE timer, starts charging in CC mode at IPRE
• Fast-charge CC starts tFAST timer, increases charge current to IFAST
• Fast-charge CV activates the constant-voltage control loop
• Start alarm: the CHG pin starts toggling

Figure 21. End-of-charge flowchart

DS11889 - Rev 6 page 20/31

 STBC03
Battery temperature monitoring

Figure 22. CC/CV charging profile (not in scale)

Charger Charger
current voltages
VFLOAT
Battery voltage

VPRE

IFAST Battery current

IPRE
IEND Time

OFF PRE-CHARGE FAST-CHARGE OFF

CC CV

8.3 Battery temperature monitoring

The STBC03 integrates all the needed blocks to monitor the battery temperature through an external NTC
resistor. The battery temperature monitoring is enabled only during the battery charging process, in order to save
power when the system is supplied from the battery.
When the battery temperature is outside the normal operating range (0-45 °C), the charging process is halted, an
alarm signal is activated (the CHG pin toggles at 16.2 Hz) but the charging timeout timers are not stopped.
If the temperature goes back to the normal operating range, before the maximum charging time has elapsed, the
charging process is resumed and the alarm signal is cleared.
In case of the charging timeout expires and the temperature is still outside the normal operating range, the
charging process is stopped but it can be still restarted using the CEN pin.
Both temperature thresholds feature a 3 °C hysteresis. The battery temperature monitoring block is designed to
work with an NTC thermistor having R25 = 10 kΩ and ß = 3370 (Mitsubishi TH05-3H103F). If an NTC thermistor is
not used, 10 kΩ resistor must be connected to ensure the proper IC operation.

8.4 Battery overcharge protection

The battery overcharge protection is a safety feature, active when a valid input voltage is connected, preventing
the battery voltage from exceeding a VOCHG value. Should an overcharge condition be detected, the current path
from the input to the battery is opened and a fault signal is activated (the CHG pin toggles at 8.2 Hz). When
the battery voltage goes below VOCHG, normal operations can only be restarted by disconnecting and connecting
back again the input voltage (VIN).

DS11889 - Rev 6 page 21/31

 STBC03
Battery over-discharge protection

8.5 Battery over-discharge protection

The battery over-discharge protection is a safety feature enabled only when no valid input voltage source (VUVLO
< VIN < VINOVP) is detected. Therefore, when the STBC03 and the system are powered off from the battery, an
over-discharge of the battery itself is avoided. Should the battery voltage level be below VODC for more than
tODD (over-discharge state), the STBC03 turns off and current sunk from the battery is reduced to less than 50
nA. When a valid input voltage source is detected, while the battery is in an over-discharge state, the STBC03
charger, SYS and LDO outputs are enabled. This condition persists until the battery voltage has exceeded the
over-discharge released threshold (VODCR), otherwise any other disconnection of a valid input voltage source
brings back the STBC03 to a battery over-discharge state.

8.6 Battery discharge overcurrent protection

When the STBC03 is powered off from the battery connected to the BAT pin, a discharge overcurrent protection
circuit disables the STBC03 if the current sunk from the battery is in excess of IBATOCP (900 mA typical) for more
than tDOD.
The presence of a valid input voltage source or triggering the WAKE-UP input pin, allows normal operating
conditions to be restored.

8.7 Battery fault protection

The STBC03 features a battery fault protection. The STBC03 charger is stopped if the battery voltage remains
below 1 V for at least 16 seconds.

8.8 Floating voltage adjustment

The STBC03 features a floating voltage adjustment, controlled via the external resistor RFLOAT connected
between battery and BATSNSFV. For safety reasons, the battery voltage overcharge threshold level (VOCHG)
is linked to any floating voltage set.

8.9 Input overcurrent protection

When the STBC03 is powered off from a valid input voltage source, a current limitation circuit prevents the input
current from increasing in an uncontrolled manner in case of excessive load. In fact, when VSYS is lower than
VILIMSCTH, the input current is limited so to have a reduced power dissipation. As soon as VSYS increases over
VILIMSCTH, the input current limit value is increased to IINLIM.

8.10 SYS short-circuit protection, LDO current limitation

In battery mode condition, if a short-circuit on the SYS pin happens, the STBC03 is turned off (no deglitch). This
short-circuit protection occurs until the SYS voltage drops below VSCSYS.
If the LDO output is in a short-circuit condition, the maximum delivered current is limited to ISC.

8.11 IN overvoltage protection

Should the input voltage source temporarily be VIN>VINOVP (for example due to a poorly regulated voltage
source), then the STBC03 is powered off from the battery, thus any load connected to SYS is protected.
As soon as the input voltage source goes back within a valid input range (VUVLO < VIN < VINOVP), the STBC03 is
then powered off again from VIN.

8.12 Shutdown mode

Asserting the SD pin high forces the STBC03 to enter in shutdown mode (low power), the current sunk from the
battery is reduced to less than 50 nA. Both SYS and LDO pins are not supplied. Normal operating conditions
are restored either by connecting a valid input voltage source (VUVLO<VIN < VINOVP) for at least tPW-VIN or by
connecting the WAKE-UP pin to VBAT for at least tPW-WA.

DS11889 - Rev 6 page 22/31

 STBC03
Thermal shutdown

8.13 Thermal shutdown

The STBC03 is fully protected against overheating. During the charging process, if a TWRN< TSD temperature
level is detected, a warning is signaled via the CHG output (toggling at 14.2 Hz). In this condition, the
programmed IPRE and IFAST are temporary halved. In case of a further temperature increase (up to TSD) the
STBC03 turns off, thus stopping the charging process. This condition is latched and normal operation can be
restored only by disconnecting and reconnecting back again a valid input voltage source on the VIN pin.

8.14 Reverse current protection

When the input voltage (VIN) is higher than VUVLO, but lower than the battery voltage VBAT (VUVLO < VIN < VBAT)
the current path from BAT to IN is opened so to stop any reverse current flowing from the battery to the input
voltage source. This event is signaled through the CHG flag.

DS11889 - Rev 6 page 23/31

 STBC03
Package information

9 Package information

In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages,
depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product
status are available at: www.st.com. ECOPACK is an ST trademark.

9.1 Flip Chip 30 (2.59x2.25 mm) package information

Figure 23. Flip Chip 30 (2.59x2.25 mm) package outline

DS11889 - Rev 6 page 24/31

 STBC03
Flip Chip 30 (2.59x2.25 mm) package information

Table 11. Flip Chip 30 (2.59x2.25 mm) package mechanical data

mm
Dim.
Min. Typ. Max.

A 0.50 0.55 0.60

A1 0.17 0.20 0.23
A2 0.33 0.35 0.37
b 0.23 0.26 0.29
D 2.56 2.59 2.62
D1 2
E 2.22 2.25 2.28
E1 1.6
e 0.40
SE 0.20
SD 0.20
fD 0.285 0.295 0.305
fE 0.315 0.325 0.335
ccc 0.075

Note: The terminal A1 on the bumps side is identified by a distinguishing feature (for instance by a circular "clear
area", typically 0.1 mm diameter) and/or a missing bump. The terminal A1 on the backside of the product is
identified by a distinguishing feature (for instance by a circular "clear area", typically between 0.1 and 0.5 mm
diameter, depending on the die size).

Figure 24. Flip Chip 30 (2.59x2.25 mm) recommended footprint

DS11889 - Rev 6 page 25/31

 STBC03

Revision history
Table 12. Document revision history

Date Revision Changes

10-Nov-2016 1 Initial release.

07-Feb-2017 2 Datasheet promoted from preliminary to production data.
Updated Table 5: "Electrical characteristics".
28-Aug-2017 3
Updated Figure 19: "STBC03 block diagram".
06-Mar-2018 4 Updated Figure 4. Thermal management.
26-May-2020 5 Updated Section 6.12 CEN

03-Mar-2022 6 Updated tPW-VIN Typical value in Table 5

DS11889 - Rev 6 page 26/31

 STBC03
Contents

Contents
1 Application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4 Electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 Functional pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6.1 GND, AGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 NTC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3 ISET, IPRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.4 BATMS, BATMS_EN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.5 BATSNS, BATSNSFV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.6 BAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.7 IN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.8 SYS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.9 LDO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.10 WAKE-UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.11 CHG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.12 CEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.13 SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.14 SW1_OA, SW1_OB, SW1_I, SW2_OA, SW2_OB, SW2_I . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.15 SW_SEL1 and SW_SEL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8 Operation description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
8.1 Power-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.2 Battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.3 Battery temperature monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.4 Battery overcharge protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.5 Battery over-discharge protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.6 Battery discharge overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.7 Battery fault protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.8 Floating voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.9 Input overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.10 SYS short-circuit protection, LDO current limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.11 IN overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DS11889 - Rev 6 page 27/31

 STBC03
Contents

8.12 Shutdown mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8.13 Thermal shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.14 Reverse current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9 Package information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
9.1 Flip Chip 30 (2.59x2.25 mm) package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

DS11889 - Rev 6 page 28/31

 STBC03
List of tables

List of tables
Table 1. Typical bill of material (BOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table 2. Pin description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 3. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 4. Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 5. Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 6. Charging current setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 7. SYS voltage source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 8. CHG pin state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 9. SW_SEL1, SW_SEL2 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 10. IFAST and IEND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 11. Flip Chip 30 (2.59x2.25 mm) package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 12. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

DS11889 - Rev 6 page 29/31

 STBC03
List of figures

List of figures
Figure 1. STBC03 application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2. Pin configuration top through view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 3. Battery mode 3 V LDO load transient response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4. Thermal management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5. VIN mode, overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 6. Pre-charge to fast charge mode transition threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 7. Pre-charge to fast charge mode transition deglitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 8. Pre-charge to fast charge mode to no charge mode transition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 9. Wake-up pin operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 10. VIN plug, charging initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 11. Wake-up operation, VSYS and LDO rise overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 12. Wake-up operation, VSYS and LDO rise detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 13. VIN plug, charging initialization battery mode to VIN mode transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 14. Shutdown mode entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 15. VBAT to VSYS drop and VSYS to VLDO drop (10 mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 16. VBAT to VSYS drop and VSYS to VLDO drop (100 mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 17. CEN operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 18. CEN operation, VIN plug/unplug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 19. STBC03 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 20. Charging flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 21. End-of-charge flowchart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 22. CC/CV charging profile (not in scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 23. Flip Chip 30 (2.59x2.25 mm) package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 24. Flip Chip 30 (2.59x2.25 mm) recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

DS11889 - Rev 6 page 30/31

 STBC03

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2021 STMicroelectronics – All rights reserved

DS11889 - Rev 6 page 31/31