PCM Connector for Inputs and Outputs

PCM Inputs and Outputs at PCM Connector E (80P)

1 2 3 4 5 6 7 8 9 10 11 12 13
YEL BLK PUR GRN BLU LT YEL - RED PUR RED LT TAN
GRN BLU
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
BLU GRY RED LT PNK WHT RED TAN WHT LT BLU GRN WHT PNK BLK
BLU GRN
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
LT WHT YEL LT BRN LT - TAN RED YEL TAN - PNK YEL GRN LT - -
GRN GRN BLU BLU
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
BLU BLK LT PUR RED YEL BRN PUR LT GRY BRN GRY BLU BRN PNK BLU GRN RED
BLU GRN
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
PNK WHT BLU PNK GRY GRN WHT PNK BLU GRN LT RED GRY TAN - PUR
BLU

Terminal side of female terminals

Terminal Terminal name Description

number
1 SO2 HT (SECONDARY HEATED OXYGEN SENSOR (SECONDARY HO2S) (SENSOR Drives secondary HO2S (sensor 2) heater
2) HEATER)
2 GND1 (GROUND) Ground for PCM
3 INJ1 (No. 1 INJECTOR) Drives No. 1 injector
4 INJ4 (No. 4 INJECTOR) Drives No. 4 injector
5 E EGR (EXHAUST GAS RECIRCULATION (EGR) VALVE) Drives EGR valve
6 MRLY (PGM-FI MAIN RELAY 1) Drives PGM-FI main relay 1
7 IGP (POWER SOURCE) Power source for PCM
8 Not used
9 ACC (A/C COMPRESSOR CLUTCH RELAY) Drives A/C compressor clutch relay
10 FANH (RADIATOR FAN CONTROL) Drives A/C condenser fan relay, fan control relay
11 F-CAN_L (CAN COMMUNICATION SIGNAL LOW) Sends and receives communication signal
12 MTR 1 (THROTTLE ACTUATOR -SIDE) Ground for throttle actuator
13 VBDBW (IGNITION SIGNAL ETCS) Detects ignition signal
14 AFHT (AIR FUEL RATIO (A/F) SENSOR (SENSOR 1) HEATER CONTROL) Drives A/F sensor (sensor 1) heater
15 DBWRLY (ELECTRONIC THROTTLE CONTROL SYSTEM (ETCS) CONTROL RELAY) Drives electronic throttle control system (ETCS) control relay
16 INJ2 (No. 2 INJECTOR) Drives No. 2 injector
17 INJ3 (No. 3 INJECTOR) Drives No. 3 injector
18 IG1(F/P) (IGNITION SIGNAL) Detects ignition signal
19 +B(ECU) (VOLTAGE BACK UP) Power source for PCM
20 VTS (ROCKER ARM OIL CONTROL SOLENOID) Drives rocker arm oil control solenoid
21 PC SOL (EVAPORATIVE EMISSION (EVAP) CANISTER PURGE VALVE) Drives EVAP canister purge valve
22 FANL (RADIATOR FAN CONTROL) Drives radiator fan relay
23 STRLY2 (STARTER RELAY 2) Drives starter cut relay 2
24 IMOFLR (IMMOBILIZER FUEL PUMP RELAY) Drives PGM-FI main relay 2
25 STRLY1 (STARTER RELAY 1) Drives starter cut relay 1
26 F-CAN_H (CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal
27 MTR 2 (THROTTLE ACTUATOR +SIDE) Drives throttle actuator
28 GND2 (GROUND) Ground for PCM
*1: Manual A/C (without heater core)
*2: Manual A/C
*3: With MAF sensor
 Terminal Terminal name Description
number
29 IGN03 (No. 3 IGNITION COIL PULSE) Drives No. 3 ignition coil
30 IGN04 (No. 4 IGNITION COIL PULSE) Drives No. 4 ignition coil
31 STRLD (STARTER RELAY RETURN SIGNAL) Detects starter cut relay
32 TW (ENGINE COOLANT TEMPERATURE (ECT) SENSOR) Detects ECT sensor signal
33 VSPOUT (VEHICLE SPEED SIGNAL OUTPUT) Sends vehicle speed signal
34 AFS- (AIR FUEL RATIO (A/F) SENSOR (SENSOR 1) -SIDE) Detects A/F sensor (sensor 1) signal
35 Not used
36 THL2 (THROTTLE POSITION (TP) SENSOR B) Detects TP sensor B signal
37 THAP1 (ACCELERATOR PEDAL POSITION (APP) SENSOR A) Detects APP sensor A signal
38 VCC3 (TH) (SENSOR VOLTAGE) Provides sensor reference voltage
39 VCC4 (SENSOR VOLTAGE) Provides sensor reference voltage
40 Not used
41 VCC1 (SENSOR VOLTAGE) Provides sensor reference voltage
42*1 ACTEMP (TEMPERATURE CONTROL DIAL) Detects temperature control dial signal
43 CLSW (CLUTCH PEDAL POSITION SWITCH) Detects clutch pedal position switch signal
44 SNET 5V (SERIAL COMMUNICATION FOR IMMOBILIZER) Sends serial communication signal
45 Not used
46 Not used
47 IGN02 (No. 2 IGNITION COIL PULSE) Drives No. 2 ignition coil
48 SG7 (KNOCK SENSOR GROUND) Sensor ground for knock sensor
49*2 TAC (EVAPORATOR TEMPERATURE SENSOR) Detects evaporator temperature sensor signal
50 TA (INTAKE AIR TEMPERATURE (IAT) SENSOR) Detects IAT sensor signal
51 AFS+ (AIR FUEL RATIO (A/F) SENSOR (SENSOR 1) +SIDE) Detects A/F sensor (sensor 1) signal
52*3 VGP (MASS AIR FLOW (MAF) SENSOR +SIDE) Detects MAF sensor signal
53*3 VGM (MASS AIR FLOW (MAF) SENSOR -SIDE) Ground for MAF sensor signal
54 MAP(PB) (MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR) Detects MAP sensor signal
55 THL1 (THROTTLE POSITION (TP) SENSOR A) Detects TP sensor A signal
56 SG3 (SENSOR GROUND) Sensor ground
57 SG4 (SENSOR GROUND) Sensor ground
58 SG2 (SENSOR GROUND) Sensor ground
59 SG1 (SENSOR GROUND) Sensor ground
60 CRK GND (CRANKSHAFT POSITION (CKP) SENSOR/CAMSHAFT POSITION Sensor ground for CKP sensor/CMP sensor
(CMP) SENSOR GROUND)
61 STS (STARTER SWITCH SIGNAL) Detects starter switch signal
62 CRMTCLS (CLUTCH PEDAL POSITION SWITCH) Detects clutch pedal position switch signal
63 BKSWNC (BRAKE PEDAL POSITION SWITCH) Detects brake pedal position switch signal
64 BKSW (BRAKE PEDAL POSITION SWITCH) Detects brake pedal position switch signal
65 IGN01 (No. 1 IGNITION COIL PULSE) Drives No. 1 ignition coil
66 KNOCK (KNOCK SENSOR) Detects knock sensor signal
67 SO2TSG (SECONDARY HEATED OXYGEN SENSOR (SECONDARY HO2S (SENSOR Sensor ground for secondary HO2S (sensor 2)
2)) SENSOR GROUND)
68 SO2T (SECONDARY HEATED OXYGEN SENSOR (SECONDARY HO2S) (SENSOR Detects secondary HO2S (sensor 2) signal
2))
69 ACPD (A/C PRESSURE SENSOR) Detects A/C pressure sensor signal
70 THAP2 (ACCELERATOR PEDAL POSITION (APP) SENSOR B) Detects APP sensor B signal
71 EGR L (EXHAUST GAS RECIRCULATION (EGR) VALVE POSITION SENSOR) Detects EGR valve position sensor signal
72 VCC5 (SENSOR VOLTAGE) Provides sensor reference voltage
*1: Manual A/C (without heater core)
*2: Manual A/C
*3: With MAF sensor
 Terminal Terminal name Description
number
73 SG5 (SENSOR GROUND) Sensor ground
74 TDC (CAMSHAFT POSITION (CMP) SENSOR) Detects CMP sensor signal
75 NC (COUNTERSHAFT SPEED SENSOR) Detects output shaft (countershaft) speed sensor signal
76 CRKN (CRANKSHAFT POSITION (CKP) SENSOR) Detects CKP sensor signal
77 SCS (SERVICE CHECK SIGNAL) Detects service check signal
78 OIL PRESS SW (OIL PRESSURE SWITCH) Detects engine oil pressure switch signal
79 Not used
80 LIN (LOCAL INTERCONNECT NETWORK) Sends and receives communication signal
*1: Manual A/C (without heater core)
*2: Manual A/C
*3: With MAF sensor