MODEL

SERVICE MANUAL RCD5355

CAUTION: Before servicing the chassis, read the "Important Service Safety Information"
section on page 2 of this manual.

PORTABLE AM/FM RADIO CASSETTE RECORDER WITH CD PLAYER

SPECIFICATIONS CONTENTS
AM/FM TUNER SECTION IMPORTANT SERVICE SAFETY INFORMATION 2

ANTENNA SYSTEM AM: FERRITE BAR DISASSEMBLY INSTRUCTIONS 3

FM: TELESCOPIC
ALIGNMENT PROCEDURES 4
TUNING RANGE AM(MW): 522~1620KHz
FM: 87.5~108KHz ADJUSTMENT LOCATION 5

INTERMEDIATE FREQUENCY AM: 455KHz +/-5KHz BLOCK DIAGRAM 6

FM: 10.7MHz +/-0.1MHZ
AUDIO SECTION WIRING DIAGRAM 7

SPEAKER IMPEDANCE 8 ohms IC BLOCK DIAGRAM 8-11

GENERAL PRINTED CIRCUIT BOARDS 12-16

POWER INPUT AC 230V, 50Hz SCHEMATIC DIAGRAMS 17-20

AC POWER CONSUMPTION 14W DC 12V EXPLODED VIEW 21

EXPLODED VIEW PARTS LIST 22

REPLACEMENT PARTS LIST 23-28

SERVICE PUBLICATION
 IMPORTANT SERVICE SAFETY INFORMATION

1. SAFETY PRECAUTIONS ANTENNA

Before returning a unit to the customer, always make a safety check of TERMINAL
the entire unit, including, but not limited to the following items:
a. Be sure that no built-in protective devices are defective and/or have
been defeated during servicing. EXPOSED
(1) Protective shields are provided to protect both the technician and METAL
the customer. Correctly replace all missing protective shields PART OM
OHMMETER
including any removed for servicing convenience.
(2) When reinstalling the chassis and/or other assemblies in the
2. PRODUCT SAFETY NOTICE
cabinet, be sure t put back in place all protective devices, including,
Some electrical and mechanical parts have special safety related
but not limited to, nonmetallic control knobs, insulating fishpapers,
characteristics which are often not evident from visual inspection, nor
adjustment and compartment covers/shields and isolation resistor/
can the protection they give necessarily be obtained by replacing them
capacitor networks. Do not operate this unit or permit it to be
with components rated for higher voltage, wattage, etc. Parts that
operated without all protective devices correctly installed and
have special safety characteristics are identified by a on
functioning.
schematic and parts list. Use of a substitute replacement that does not
b. Be sure that there are no cabinet openings through which an adult or have the same safety characteristics as the recommended
child might be able to insert their fingers and contact a hazardous replacement part might create shock, fire, and/or other hazards.
voltage. such openings include, but are not limited to, excessively wide Product safety is under review continuously and new instructions are
cabinet ventilation slots, and an improperly fitted and/or incorrectly issued whenever appropriate.
secured cabinet back cover.
3. SERVICING PRECAUTIONS
c. Leakage Current Hot Check - With the unit completely reassembled, CAUTION”Before servicing the unit covered by this service manual
plug the AC line cord directly into a 120V AC outlet. (Do not use an and its supplements read and follow the SAFETY PRECAUTIONS on
isolation transformer during this test.) Use a leakage current tester or a this page. NOTE”If unforeseen circumstances create a conflit
metering system that complies with American National Standards between the following servicing precautions and any of the safety
institute (ANSI) C101.1”Leakage current for Appliances” and precautions, always follow the safety precautions. Remember: Safety
Underwriters laboratories (UL) 1410,(50.7). With the unit AC switch first First.
in the ON position and then in the OFF position, measure from a known General Servicing Precautions.
earth ground (metal water pipe, conduit, etc.), especially any exposed a. Always unplug the unit’s AC power cord from the AC power
metal parts that offer an electrical return path to the chassis. Any source before:
current measured must not exceed 0.5 milliamp. Reverse the unit power (1) removing or reinstalling any component, circuit board, module, or
cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT any other unit assembly.
WITHIN THE LIMITS SPECIFIED HERENIN INDICATE A POTENTIAL (2) disconnecting or reconnecting any unit electrical plug or other
SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE electrical connection.
RETURNING THE UNIT TO THE CUSTOMER. (3) connecting a test substitute in parallel with an electrolytic
capacitor in the unit.
Caution: A wrong part substitution or incorrect polarity installation
of electrolytic capacitors may result in an explosion
hazard.
b. Do not defeat any plug/socket B+ voltage interlocks with which
the unit covered by this service manual might be equipped.
(READING SHOULD
NOT BE ABOVE
c. Do not apply AC power to this unit and/or any of its electrical
0.5mA) assemblies unless all solid-state device heat sinks are correctly
installed.
AC Leakage Test
d. always connect a test unit instrument’s ground lead to the unit’s
TEST ALL
DEVICE EXPOSED METAL chassis ground before connecting the test instrument’s positive
UNDER SURFACES + lead. Always remove the test instrument’s ground lead last.
TEST LEAKAGE
CURRENT 4. LASER PRECAUTIONS
TESTER WARNING!!
2-WIRE CORD 1. When servicing, (in case it is necessary to confirm Laser Beam
ALSO TEST WITH
PLUG REVERSED EARTH Emission) be sure not to place your eyes any closer than 1 ft or
(USING AC ADAPTER GROUND 30cm from the surface of the Objective Lens on the Opticval
PLUG AS REQUIRED) Pickup Block.
HANDLING THE LASER PICKUP
2. Laser diodes are extremely susceptible to damage from static
electricity. Even if a static discharge does not ruin the diode, it can
shorten its life or cause it to work improperly. When replacing the
pickup, use a conductive mat on the floor and desk and wear a
wrist band connected to ground through a 1M ohm resistor to
d. Insulation Resistance Test Cold Check protect the laser diode from static damage. If the lens should get
Unplug the power supply cord and connect a jumper wire between the dusty, blow off the dust carefully from the object.
two prongs of the plug. 3. There are no adjustable parts in the pickup assembly. If it is
Turn on the power switch of the unit. defective, replace the whole pickup assembly.
Measure the resistance with an ohmmeter between the jumpered AC CAUTION:
plug and each exposed metallic cabinet part on the unit, such as USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF
screwheads, antenna, control shafts, handle brackets, etc. When the PROCEDURES HEREIN MAY RESULT IN HAZARDOUS
exposed metallic part has a return path to the chassis, the reading RADIATION EXPOSURE.
should be between 1 and 5.2 megohms. When there is no return path to DANGER:
the chassis, the reading must be “infinite”. If it is not within the limits IF INTERLOCK FAILS OR IS DEFEATED, THE LASER LIGHT IS
specified, there is the possibility of a shock hazard, and the unit must be ABLE TO FUNCTION. THE LASER IS INVISIBLE, AVOID DIRECT
repaired and rechecked before it is returned to the customer. EXPOSURE TO BEAM.

2
 DISASSEMBLY INSTRUCTIONS

1) ROTATE THE UNIT TO EXPOSE THE BACK SIDE.

2) REMOVE THE 10 SCREWS AS SHOWN IN FIG.1.

FIG.1

3
 ALIGNMENT PROCEDURES

AM I.F. ALIGNMENT
1. Set the POWER BUTTON to POWER "ON".
2. Set the FUNCTION SELECTOR SWITCH to RADIO & AM BAND.
3. Connect a SWEEPSCOPE OUTPUT to AM antenna terminal.
4. Connect a SWEEPSCOPE INPUT to pin16 or 17 of IC001 through a 1uf capacitor and ground.
STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR
CENTER
1 455KHz GANG OPEN CF2(AM IF)
& MAXIMUM OUTPUT

AM R.F. ALIGNMENT
1. Connect an RF generator to a standard radiating loop.
2. Connect a SCOPE and VTVM across the speaker output.
STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR
1 522KHz GANG CLOSED IF2 (AM OSC COIL)
2 1620KHz GANG OPEN TC2 (AM OSC TRIM.) MAXIMUM
3 600KHz 600KHz AM COIL (AM ANT COIL) OUTPUT
4 1400KHz 1400KHz TC1 (AM ANT TRIM.)
5 REPEAT STEPS 3 AND 4 TO OBTAIN BEST TRACKING.

FM I.F. ALIGNMENT
1. Set the POWER SWITCH to POWER "ON".
2. Set the FUNCTION SELECTOR to RADIO & FM BAND.
3. Connect a SWEEPSCOPE OUTPUT to pin5 of IC001 through a 20pF capacitor and ground.
4. Connect a SWEEPSCOPE INPUT to pin16 or 17 of IC001 through a 1uf capacitor and ground.
STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR

1 10.7MHz GAND OPEN CF1 (FM ORG) MAX.AMPLITUDE

BALANCED CURVE

FM R.F. ALIGNMENT
1. Connect an RF generator to the FM antenna terminal and ground.
2. Connect a SCOPE & VTVM across the speaker output.
STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR
1 87.5MHz GANG CLOSED L4 (FM OSC COIL)
2 90MHz 90MHz L3 (FM RF COIL) MAXIMUM
3 106MHz 106MHz TC3 (FM RF TRIM) OUTPUT
4 REPEAT STEPS 3 AND 4 TO OBTAIN MAX ADJUST.

CASSETTE ALIGNMENT
1. Set the FUNCTION SELECTOR SWITCH TO TAPE.
2. Connect a Scope & VTVM across the speaker output.
3. Insert the 8KHz tape in to cassette deck and push play BUTTON. SCREWDRIVER
4. ADJUST HEAD for speaker maximum output.
ADJUSTING
5. Motor speed adjustment for tape speed. SCREW

CD ALIGNMENT MOTOR SCREWDRIVER

Auto alignment.

4
 TC2 TC1

IF2

L3
MAIN PCB

5
TC3

L4

Cf2

CF1
ADJUSTMENT LOCATIONS
 TB2132FN
FM/AM IF
AM 'RF
FM 'RF

TUNER
TAPE

6
PRE. AMP POWER AMP
DECK UTC1316
CS-21V-205 BA3308
BLOCK DIAGRAM

CD
CD MECH TA2157FN
(SANYO) SA1469XH LCD
DA11B3V TC94A09F DISPLAY
TC94A02F
POWER SUPPLY
 CD DOOR

CN8
CN5
TRANSFOMER
AC2 AC1 JP3
CN2

JP1
JP2

CN3

MAIN PCB

CN1 CON1

7
CN4
FM.ANT
CON1
CN9
CN10
WIRING DIAGRAM

CN2 TO JP3
CN6

CN7
MIC

TO JP1 DISPLAY PCB

MOTOR
CD DECK

CASSETTE DECK
CN15
 2Vref
Vref
PVref
LPFN

SEL
TEZI
TEI
FEI
RFZI
RFCT

TEBC
RFGC
RFRP

XVDD
XO
VDD
DMO
FMO
TRO
FOO
SBAD
AVDD
SLCO
LPFO

VCOF

XVSS
VSS
AVSS

X1
RF1
51

80
50

81
TMAX

60
55

65

75
TC94A09F

70
DVSR
PDO
RO
CD input/output port P2Vref
DVRR
VSS
DVDD
VDD

85
DCRL

45
SBOK
LO
SBSY
DVSI
DOUT
TESTM
COFS/OT22:Preset EQ2
SyncReclnput:IN2/VPP
SPDA/OT21:Preset EQ1/X-BASS

90
/RST Input port
40

Top View
Reset input SPCK/OT20:PLL CE
Powerdetect:/HOLD

(QFP100pin)
Hold input
Interrupt input /HSO/OT19:E-Vol CE
Remoteinput:/INTR
Test input TESTC

TC94A09F-202
MXO MCU Oscillator
MXI INI:Door-OP Input
Input port

8
P2-3:Door-CL Input

95
MVSS
MCU Power supply
35

MVDD P2-2:Tray-OP Output

COM1/OT1 I/O port P2-1:Tray-CL Output

LCD/LED driver .I/O.CD output port MCU
(LCD:4*18-Max.72segment) P2-0:CD-RW gain/STin
COM2/OT2 Power supply
(LED:Max.18 segment) I/O port P4-3/SCK/SCL:SCK
COM3/OT3

1
5
P4-2/Sin1/SDA:SDATA

100
20
25

10
30
IC BLOCK DIAGRAMS

31

15
COM4/OT4
P1-0
P1-1
P1-2
P1-3
P3-0

MVSS
MVDD

S1 OT5
S2 OT6
S3 OT7
S4 OT8
S5 OT9
S7 OT11
S6 OT10
S8 OT12
S9 OT13
S15 P8-0
S16 P8-1
S17 P8-2
S18 P8-3
P4-1 Sin2

S11 OT15
S10 OT14
S12 OT16
S13 OT17
S14 OT18
P3-1 ADin1
P3-2 ADin2
P3-3 ADin3
P4-0 ADin4

:Mute
:KeyAD1
:Key AD2
:Key AD3

:Powrt Out
:Function out

:PU Inner SW

LCD Output
:Function Select A
:Function Select B
:PUH&CLK Select
 TA2153FN

36pF

10K 50K

FEO 16 15K 15 SBAD

10pF 15K
3pF
- +
FEN 17 30K +
14 TEO
10k -
60K + 20K
10k
- 10pF
SEB 18 13 TEN

3 pF
30K
-
VRO 19 12 2VRO
+ 20K
20K 20K +
12K
- 3 STATE
-
RFRP 20 12K 11 TEB
+ DET

21.82K
11K 48K
20K
100 83K
BTC 21 SW1
+ 2.9K 10 SEL
- 1K
100K

-
+ SW2
+
RFCT 22 9 LDO
- SW3
-
100K

1.4K
+
238K
PKC 23 8 MDI
11K 15pF 10K 2.20K
-
BOTTOM
RFRPIN 24 + 1-1 7 TNI
PEAK 238K
20k

15pF

RFGO 25 - 1-1 6 TPI

+
150k
GVSW 26 90k 20k 40pF 5 FPI
60k
1K
60k -
- +
AGCN 27 AGC Amp 1K
+ 4 FNI
40pF

150K

RFO 28 3 GMAD

GND 29 2 RFGC

- +
RFN 1 Vcc

PT7117

9
SC9243

VSS VDD OSCI OSCO TEST

Reset Oscillator
Circuit Oscillator
Control Circuit

K10
Function LED
K11 Frequency Generator
Division Code
Key Circuit Output
K12 Circuit DOUT
Input
K13
Code
Scan Scan Generator
K14
Control Circuit
K15 Circuit
Key Output Signal CODE Port
K16 Generator Circuit

K17

KO0 KO1 KO2 KO3 CODE

SA1469XH

IS62LV1024L

512 X 2048
A0-A16 DECODER MEMORY ARRAY

VCC
GND

I/O
I/O0-1/O7 DATA COLUMNI/O
CIRCUIT

CE1
CE2 CONTROL
OE CIRCUIT
WE

10
UTC1316
Vcc
INPUT2 C5 220 F
C6 C7
100 F 0.1 F R2
1
#C4
C1 0.01 F
100 F
(Rf) C2(Cb) C3
R1 22pF 100 F
33

14 13 12 11 10 9 8

AMP2

H/S

AMP1

1 2 3 4 5 6 7
(Rf) C10
C8 R3 100 F C13 220 F
47 F 33

C9 #C12
C11(Cb) 0.01 F
INPUT1 100 F 22pF
R4
1

TB2132F
FM TV RF AM FM/TV AM PLL OUT2 OUT1 PLL
RF out RF out VCC RFin OSC OSC CE CK DATA VCC Do (DO) (ST) GND XO
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

OSC AM AMOSCin
PLL
AM OSC FMOSCin
MIX IFin
1/2N AM
TV1/8
1/4 BUFF
1/16 1/8 FM/AM/TV
FM1/16 SW
TV FM/TV1/2 AM
RF INV
FM
IF
FM/TV BUFF FM FM MPX
FM MIX DET
RF
AM
DET
FM AM AF MUTE
AGC
IF IF

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

FM/TV GND MIX AGC FM V CC AM OUAD DET MPX LPF1 LPF2 L-ch R-ch X1
RF in out Ifin IFin out in

BA3308

MUTE

_ _
ch1 ch2
+ +

ALC

1 2 3 4 5 6 7 8 9
N I O G A V O I N
F N U N L c U N F
1 P T D C c T P 2
U P P U
T U U T
1 T T 2
1 11 2
17
18
19
 REPLACEMENT PARTS LIST
PART NO. DESCRIPTION REF NO.
02-17P020510010 RMEOTE CONTROL ASS'Y (有MP3) "UNITED"
05-13P020310000 REMOTE BD ASS'Y (有MP3)
11-MMBT39040021 TRANSISTORS MMBT3904LT1 Q1
12-PMLL4148L021 SMD DIODE PMLL4148L D1
13-021500020020 INFRARED LED 5mm #SIR-563-ST-3F .
16-SC9243S00021 IC (LIBERAL) SC9243S IC1
21-203000002225 CHIP RESISTORS 0Ω 1/16W (1608) J1-J6
21-203122062225 CHIP RESISTORS 2.2Ω 1/16W +-5% (1608) R2
21-203422062225 CHIP RESISTORS 2.2K 1/16W +-5% (1608) R1
25-014100934221 CHIP CAPACITOR 100PF 50V +-5% (1608) C1,2
26-015470651121 E.CAP 47UF 10V +-20%(4x7mm) C3
31-046455000120 RESONATOR S455E X1
41-150010050020 TACT SWITCH 6x6mm 5mm (250g+-20g)4LEGS
48-13PM20300220 REMOTE PCB 60x34x1.6mm (MP3)
06-17P020510010 REMOTE CASING ASS'Y (有MP3) "UNITED"
56-43SD66P0A0E0 REMOTE FRONT CAB"UNITED"(ABS)(SIL.TN8-7)
56-43SD66P1A020 REMOTE REAR CAB(ABS)(SILTN8-7)(D.GERY426
56-44SD66P0A020 REMOTE BATTERY DOOR (ABS) (SIL.TN8-7)
56-54SD66P3A000 REMOTE SKIP KNOB-2KEY (ABS)(SIL.TN8-7)
56-54SD66P4A000 REMOTE CONTROL KNOB-3KEY(ABS)(SIL.TN8-7)
56-54SD66P5A000 REMOTE POWER KNOB (ABS) (SIL.TN8-7)
56-54SD66P6A060 REMOTE INLAY KNOB (ABS) (SIL.TN8-7)
56-54SD66P7A000 REMOTE PLAY KNOB-2KEY (ABS) (SIL.TN8-7)
57-33P020300120 REMOTE PLATE (D66P模) (银底灰字)
58-192502500020 FELT 5x5x0.5mm W/TAPE >TACT SWITCH
58-19C200000020 FELT DIA:5x8x0.02mm W/TAPEx1 >TACT SWITCH x4
58-82A150000120 SPONGE 28x22x6mm W/TAPE 28x22mm
61-25SD66P00020 BATTERY SPRING (+)
61-25SD66P10020 BATTERY SPRING (+ -)
61-26PCD2210020 BATTERY SPRING (-)
66-140320180321 SELF-TAPPING SCREW TA/PH 2x8mm
66-140326160321 SELF-TAPPING SCREW TA/PH 2.6x6mm FOR REMOTE
66-150330180321 SELF-TAPPING SCREW TB/PH 3x8mm FOR REMOTE
76-520300801000 POLYBAG 3x8"x0.05mm #001R0
77-060000000020 QA LABEL
03-P02055110010 PACKING ASS'Y "UNITED" (有MP3)-瑞士
45-124180500061 AC CORD SET VDE APP 6FT (M.T) (BLK)无毒
76-01P020500320 GIFT BOX "UNITED" 312x272x172mm (有MP3)
76-02P020300021 CARTON A=B (4SETS) (556x324x366mm)
76-10P020300020 POLYFOAM -L (50+-8g)
76-10P020300120 POLYFOAM -R (50+-8g)
76-42M610R00020 POLY SHEET 1000x90x0.025mm
76-45P020300020 WAX PAPER 863x508mm
76-520301001010 POLYBAG 3x10"x0.05mm #002R2 FOR AC CORD
76-520801201030 POLYBAG 8x12"x0.05mm #4B2R4 FOR I/B
76-521451851010 POLYBAG 14.5x18.5"x0.05mm #4B2R6 FOR UNIT
77-060000000020 QA LABEL
77-070000000020 QC LABEL
77-08210000A120 COLOUR LABEL 10mm (SILVER)
77-082300000020 CLEAR LABEL 30mm
77-092441700000 SERIAL NO.LABEL 44x7mm
77-11P020500220 BAR CODE LABEL (7022283253556) (有MP3)
77-20P020500423 INSTRUCTION MANUAL (E.) 230V "UNITED" R3
77-20P020500622 INSTRUCTION MANUAL (F.)"UNITED"(有MP3)R2
77-20P020500822 INSTRUCTION MANUAL(IT.)"UNITED"(有MP3)R2
77-20P020500922 INSTRUCTION MANUAL(GE.)"UNITED"(有MP3)R2
77-23CR11300220 CD TRAY CARD #Q02301
77-29MS06600020 CAUTION LABEL (E/G/SW/DE) 25x65mm
77-31P020500522 RATING LABEL "UNITED" 230V (有MP3) R2
77-48HD71000020 CLASS 1 LABEL (2) (4 LAN.) 51x23mm
77-65PCD1C10020 "SUFFIX A" LABEL
77-810000000020 LASER BEAM LABEL (TRIGONAL)
05-01P020510100 MAIN BD ASS'Y (有MP3) (1.2W) -CE (散装)
11-2SB764E00021 TRANSISTORS 2SB764-E (SANYO) Q312
11-9012G0000021 PNP TRANSISTORS 9012G 1W Q302
11-9013G0000021 NPN TRANSISTORS 9013G 1W Q8
11-9014C0000021 NPN TRANSISTORS 9014C >Q3-7,9,10,11,15,16,311,301,314
23
11-9015C0000021 PNP TRANSISTORS 9015C >Q303
12-011330320121 ZENER DIODE +-5% 3.3V 1/2W >ZD1
12-011510320121 ZENER DIODE +-5% 5.1V 1/2W ZD5,6
12-011620320121 ZENER DIODE +-5% 6.2V 1/2W >ZD2,8
12-012120320121 ZENER DIODE +-5% 12V 1/2W >ZD3
12-1N4001000021 RECTIFIER DIODE 1N4001 1A 50V >D1-4,301,302,10,310
12-1N4148000021 DIODE 1N4148 >D5,6,8,11,12,14,17,18,303,305,306,307,308,27,313,FOR J225
12-1N60P0000021 DIODE IN60P D9
12-SVC201SPA021 VARACTOR DIODE (SANYO) SVC201SPA >D7,15
12-SVC321SPA021 VARACTOR DIODE (SANYO) SVC321SPA >D13,16
16-BA3308000021 IC PRE AMP (ROHM) BA3308 >IC5
16-KA7808000021 IC (SAMSUNG) KA7808 >IC3
16-SA1469XH0021 IC （士兰） SA1469XH IC303
16-TA2153FN0021 IC CD SERVO (TOSHIBA) TA2153FN IC302
16-TB2132FN0021 IC (TOSHIBA) TB2132FN >IC4
16-TC94A09F2121 IC (TOSHIBA) TC94A09F-215 IC301
16-UTC131600021 IC POWER AMP (LIBERAL) UTC1316 >U2
21-206122060121 RESISTORS 2.2Ω 1/6W +-5% >R111,112
21-206210060121 RESISTORS 10Ω 1/6W +-5% >R301
21-206227060121 RESISTORS 27Ω 1/6W +-5% >R66,72
21-206233060121 RESISTORS 33Ω 1/6W +-5% >R61
21-206310060121 RESISTORS 100Ω 1/6W +-5% >R122,308,398,399,
21-206312060121 RESISTORS 120Ω 1/6W +-5% >R109,110
21-206315060121 RESISTORS 150Ω 1/6W +-5% >R49,50
21-206322060121 RESISTORS 220Ω 1/6W +-5% >R341,54,59,124
21-206333060121 RESISTORS 330Ω 1/6W +-5% >R57,83,98,J224
21-206339060121 RESISTORS 390Ω 1/6W +-5% >R65
21-206356060121 RESISTORS 560Ω 1/6W +-5% >R74,75
21-206410060121 RESISTORS 1K 1/6W +-5% >R84,134,307,357,318,328,385,100,377,379
21-206420060121 RESISTORS 2K 1/6W +-5% >R88,89,360
21-206422060121 RESISTORS 2.2K 1/6W +-5% >R33,85,372,305,62,123,386,393
21-206427060121 RESISTORS 2.7K 1/6W +-5% R358,FOR JP1 插座INPUT脚TO D12负极
21-206433060121 RESISTORS 3.3K 1/6W +-5% >R55,58,378
21-206439060121 RESISTORS 3.9K 1/6W +-5% FOR C338
21-206447060121 RESISTORS 4.7K 1/6W +-5% >R135,136,343,435
21-206468060121 RESISTORS 6.8K 1/6W +-5% >R68,73,92,48
21-206482060121 RESISTORS 8.2K 1/6W +-5% R395
21-206510060121 RESISTORS 10K 1/6W +-5% >R369,137,87,86,354,380,381,442,394
21-206510060121 RESISTORS 10K 1/6W +-5% R4,6,93,63,60,64,94,382,300,330,434,356,353,370
21-206510060121 RESISTORS 10K 1/6W +-5% R319,320,316,324,373,125,126,127
21-206515060121 RESISTORS 15K 1/6W +-5% >R76,78,327
21-206518060121 RESISTORS 18K 1/6W +-5% >R115,116
21-206522060121 RESISTORS 22K 1/6W +-5% >R113,114,306,315
21-206527060121 RESISTORS 27K 1/6W +-5% >R47,56
21-206539060121 RESISTORS 39K 1/6W +-5% R77,79,303,(R391 CE去向）
21-206547060121 RESISTORS 47K 1/6W +-5% >R129,131,325,302,304
21-206568060121 RESISTORS 68K 1/6W +-5% >R309,314
21-206575060121 RESISTORS 75K 1/6W +-5% >R438,439,
21-206582060121 RESISTORS 82K 1/6W +-5% >R95,96,97,130,310,311,312,313
21-206610060121 RESISTORS 100K 1/6W +-5% >R392,71,67,128,132,397
21-206622060121 RESISTORS 220K 1/6W +-5% >R1,326,441
21-206627060121 RESISTORS 270K 1/6W +-5% >R69
21-206633060121 RESISTORS 330K 1/6W +-5% R2
21-206668060121 RESISTORS 680K 1/6W +-5% >90,91
22-011225500210 ROTARY VOLUME F-122KGP A50K L=25F >VOL1
25-013300930121 CERAMIC CAP 30PF 50V +-5% >C64,65
25-013470930121 CERAMIC CAP 47PF 50V +-5% >C326
25-013560930121 CERAMIC CAP 56PF 50V +-5% >C320
25-014100930121 CERAMIC CAP 100PF 50V +-5% >C364
25-014150930121 CERAMIC CAP 150PF 50V +-5% >C86
25-014200930121 CERAMIC CAP 200PF 50V +-5% C391,392
25-014390930121 CERAMIC CAP 390PF 50V +-5% >C71,84
25-014470930121 CERAMIC CAP 470PF 50V +-5% >C335
25-015100960121 CERAMIC CAP 0.001UF 50V +80%-20% >C56,54,66
25-015150960121 CERAMIC CAP 0.0015UF 50V +80%-20% >C141,128
25-016100960121 CERAMIC CAP 0.01UF 50V +80%-20% >C136,138,59,60,61,62,322,330,340,362,314,328,323
25-016100960125 CERAMIC CAP 0.01UF 50V +80%-20%(TAPING) C137
25-016220960121 CERAMIC CAP 0.022UF 50V +80%-20% >C87
25-016470960121 CERAMIC CAP 0.047UF 50V +80%-20% C339,338,337,336
25-017100960121 CERAMIC CAP 0.1UF 50V +80-20% >C69,78,81,82,104,108,129,131,135,341,318,302,305,317
24
25-017100960121 CERAMIC CAP 0.1UF 50V +80-20% C1(IC4 17,18PN)
25-017220660121 CERAMIC CAP 0.22UF 16V +80%-20% C371,372
25-022600930121 CERAMIC CAP 6PF 50V +-5% (NPO) C388,373
25-023150930121 CERAMIC CAP 15PF 50V +-5% (NPO) C342,343,85
25-023330930121 CERAMIC CAP 33PF 50V +-5% (NPO) C360,359
25-035220930121 MYLAR CAP 0.0022UF 50V +-5% >C100,93
25-035270930121 MYLAR CAP 0.0027UF 50V +-5% C331
25-035470930121 MYLAR CAP 0.0047UF 50V +-5% >C332,357
25-035680930121 MYLAR CAP 0.0068UF 50V +-5% C101,102
25-036150930121 MYLAR CAP 0.015UF 50V +-5% >C327,72,74
25-036180930121 MYLAR CAP 0.018UF 50V +-5% >C125,126
25-036220930121 MYLAR CAP 0.022UF 50V +-5% >C98,91
25-036680930121 MYLAR CAP 0.068UF 50V +-5% C334
25-037100930121 MYLAR CAP 0.1UF 50V +-5% >C123,124
26-014101050121 E.CAP 1UF 50V +-20% >C53,57,73,75,92,99,121,122
26-014331050121 E.CAP 3.3UF 50V +-20% C208,8
26-014471050121 E.CAP 4.7UF 50V +-20% >C109,96,80,90,J143,144
26-015100750121 E.CAP 10UF 16V +-20% C88,79,110,140,94
26-015220750121 E.CAP 22UF 16V +-20% C67,348,349,FOR R56 TO D14
26-015330750121 E.CAP 33UF 16V +-20% C2
26-015470750121 E.CAP 47UF 16V +-20% >C105
26-015470850121 E.CAP 47UF 25V +-20% C325,356,329,319,313,316
26-016100750121 E.CAP 100UF 16V +-20% >C55,58,68,89,97,103,107,111,119,120,49,52,106,47,48,306,315,363
26-016220750121 E.CAP 220UF 16V +-20% >C70,324,389
26-016330650121 E.CAP 330UF 10V +-20% C95
26-016470750121 E.CAP 470UF 16V +-20% >C45,46,301
26-017100650121 E.CAP 1000UF 10V +-20% C385,390
26-017330850121 E.CAP 3300UF 25V +-20% C63
26-114101050111 E.CAP(LL) 1UF 50V +-20%(PH)I<0.01CV C130
27-501602101020 TRIMMER 10PF 6mm (WH) >TC1
27-501602202020 TRIMMER 20PF 6mm (RED) TC2,3
31-015750000020 CRYSTAL 75KHZ 12.5PF+-20PPM 3x8mm >X302
31-018169302010 CRYSTAL 16.9344MHZ HC-49/U X301
31-026450010110 CERAMIC FILTER (MURATA) SFU450B >CF2
31-028107000120 CERAMIC FILTER LT10.7MA5-A(3PIN) RED >CF1
31-038107040120 DISCRIMINATOR FILTER JT10.7MG80-A(2PIN) >CF4
32-022102800020 FERRITE BAR 10x80mm
38-013100050220 AXIAL INDUCTOR 10UH +-10% 500mA EC-36 >L301,P32
38-014100050120 AXIAL INDUCTOR 100UH +-10% 275mA EC-36 >L6
40-022490004020 I.F.T 7mm 7AC-249S0 (YELLOW) >IF1
40-022720002020 I.F.T 7mm 7AL-272HM (RED) >IF2
40-212650220020 AM COIL (AD)/M7 65:20T W:60/R:70/GB:50mm
40-351500125020 FM COIL 5x2.5T (0.8mm) >L4
40-351500135020 FM COIL 5x3.5T (0.8mm) L2,3
41-091020000010 PUSH SWITCH RSA-102D01N-TS (LUP FUNG) SW10
41-132203000620 SWITCH SKE-22F03-G6-NK/SK-22F03-G6 >SW7
41-134301000620 SWITCH SKT-43D01-G6-NS/SK-43D01-G6
41-134301000620 SWITCH SKT-43D01-G6-NS/SK-43D01-G6 >SW9
41-160040000020 V/TACT SWITCH 7x7.4mm 3.85mm 150gf 5LEGS
43-012100216120 F.F.C.WAFER 1mm 16P 180C(GREY) >CN1
43-012200120120 WAFER 2mm 2P 180C >CN7,3
43-012200130120 WAFER 2mm 3P 180C >CN6,2,3
43-012200160120 WAFER 2mm 6P 180C >CN2
43-012250140120 WAFER 2.5mm 4P 180C >CN10
43-022100217121 F.F.C.WAFER 1mm 17P 90C 1.0-11S-17PW >CN4
43-022200130120 WAFER 2mm 3P 90C JP1
43-022200140120 WAFER 2mm 4P 90C >CN5
43-022200210120 WAFER 2mm 10P 90C CON1
43-431360003020 PHONE JACK 3.6mm TC38-063-05-01 BLK RING PH1
44-110250002620 JUMPER WIRE UL1007#28 4+42+4mm (RED) R392 一端TO B2
44-110260000520 JUMPER WIRE UL1007#26 4+52+4mm (BLACK) X1-X1;FOR D12 "+" TO D302
44-110270000620 JUMPER WIRE UL1571#28 4+62+4mm (BLACK) A3 TO A3,F TO F2
44-110310002520 JUMPER WIRE UL1007#26 4+92+4mm (RED) B2-B2 x1;FOR DC TO DC x1
44-110311002520 JUMPER WIRE UL1007#26 4+102+4mm (RED) OSC TO OSC
44-110312002520 JUMPER WIRE UL1007#26 4+112+4mm (RED) A1-A1 x1; B-B1 x1
44-110315002520 JUMPER WIRE UL1007#26 4+142+4mm (RED) GND
44-566315055620 5P SHIELD WIRE L=150mm TML(2.5)x2 FOR VOL
46-015200300010 AXIAL FUSE 4x10mm W/LEAD 2A/250V >F1
48-01PM20300222 MAIN PCB 275x185x1.6mm 94HB R2
56-27000H300000 BAR HOLDER AD10mm H=30mm #EC-02
25
58-82A150000420 SPONGE 10x10x10mm (WHITE)
61-48A300000220 HEAT SINK FOR SA1469XH
61-48AE33800020 HEAT SINK (10+25+10)x30x1.0mm >FOR KA7808
66-120230150321 MACHINE SCREW MS/BH 3x5mm >FOR KA7808
67-021300000020 NUT DIA M3mm >FOR KA7808
67-102200240020 EYELET 2x4mm
67-213310000020 SOLDERING PIN #3310A
79-010100630000 BARE WIRE 0.6mm (S/N:P2) L=40mm(0.1)x121PCS
79-210101030000 UL TUBE I.DIA:1mm (S/N:P3) >L=10mmx11PCS FOR 2.7K
79-210102030000 UL TUBE I.DIA:2mm (S/N:P4) FOR AM ANT
05-04P020510000 DISPLAY BD ASS'Y (MP3)
13-05P020500121 LCD DISPLAY #IS03274P02 (W/MP3)
21-206256060121 RESISTORS 56Ω 1/6W +-5% R53
21-206415060121 RESISTORS 1.5K 1/6W +-5% >R401,404
21-206420060121 RESISTORS 2K 1/6W +-5% >R402,405
21-206427060121 RESISTORS 2.7K 1/6W +-5% >R403,406
41-150010050020 TACT SWITCH 6x6mm 5mm (250g+-20g)4LEGS >SW401-408
43-022100217121 F.F.C.WAFER 1mm 17P 90C 1.0-11S-17PW >CN15
48-04PM20500221 DISPLAY PCB 94HB (W/MP3) R1
56-07P020519000 RACKLIGHT BRACKET (ABS)
56-57P020530000 BACKLIGHT LENS (PMMA)
57-26P020500020 FILTER SHEET 49x38.2x0.3mm
66-150330160321 SELF-TAPPING SCREW TB/PH 3x6mm CONTROL PCB TO BACK LIGHT BKT x2;
79-010100530000 BARE WIRE 0.5mm (S/N:P1) L=40mm(0.07)x2PCS
05-10P020300000 MP3 BD ASS'Y
16-H1117SJ00021 IC (HI SINCERITY) H1117SJ-2.5V (SOT-223) IC4
16-IS62LV100121 IC (ICSI) IS62LV1024LL-55T IC2
16-PT7117000021 SMD(SOT-223)IC (ANGUS) PT7117 3.3V IC3
16-TC94A0200021 IC (TOSHIBA) TC94A02F-007 IC1
21-203000002225 CHIP RESISTORS 0Ω 1/16W (1608) R07,09,001
21-203327062225 CHIP RESISTORS 270Ω 1/16W +-5% (1608) R112,113,107,108
21-203422062225 CHIP RESISTORS 2.2K 1/16W +-5% (1608) R119,122,125,98,67,68
21-203447062225 CHIP RESISTORS 4.7K 1/16W +-5% (1608) R120,123,126,66
21-203510062225 CHIP RESISTORS 10K 1/16W +-5% (1608) R84,86,87,85,83,114,73,82,71,94,92,95,93,91,89,90,88,72
21-203722062225 CHIP RESISTORS 2.2M 1/16W +-5% (1608) R110
25-012600934221 CHIP CAP 6PF 50V +-0.5PF (1608) C70
25-015220944221 CHIP CAPACITOR 0.0022UF 50V +-10%(1608) C68,69
25-017100644221 CHIP CAPACITOR 0.1UF 16V +-10%(1608) C79,67,77,63,72,66,78,73,74
25-017330544221 CHIP CAPACITOR 0.33UF 10V +-10% (1608) C64
26-014331051121 E.CAP 3.3UF 50V +-20%(4x7mm) C56,57
26-016100651221 E.CAP 100UF 10V +-20%(5x7mm) C75,76
26-016100750121 E.CAP 100UF 16V +-20% FOR 供电端;C80
38-013100050220 AXIAL INDUCTOR 10UH +-10% 500mA EC-36 FOR GND
44-110328000520 JUMPER WIRE UL1007#26 4+272+4mm (BLACK) FOR R108
44-335321060520 10P RAINBOW WIRE 210mm HSG(2)x1 (#26) DIS PCB CNP2 TO CN2 MAIN PCB
44-365320053620 3P SHIELD WIRE L=200mm HSG(2)x1(2547#28) TO MAIN PCB JP2
48-10P020300323 MP3 PCB (FR4) 53x40x1.2mm R3
79-010100530000 BARE WIRE 0.5mm (S/N:P1) L=40mm x1PCS
05-17P020510000 LED BD ASS'Y (有MP3)
13-011506122020 LED LAMP 5mm (S.BLUE) ZGA2-SB14E2-560 >D1,12
48-17PM20500220 LED PCB 94HB (W/MP3)
05-23P020310000 SWITCH BD ASS'Y (有MP3)
41-180010030020 PUSH SWITCH 7x7mm PS-2203-L (W/LOCK) >SW23
44-365326053720 3P SHIELD WIRE L=260mm HSG(2)x1 2547#30 TO JP3
48-23PM20300220 SWITCH PCB (有MP3)
05-27P020310000 INFRARD RECIVER BD ASS'Y (有MP3)
17-05RPM7138010 OPTIC SENSER (ROHM) RPM7138-V4 >INTR1
44-365328053620 3P SHIELD WIRE L=280mm HSG(2)x1
48-12PM20300220 INRARD RECEIVER PCB
58-58X280000020 RUBBER 8x8x6.5mm INTR1
06-P02055110010 CASING ASS'Y 230V(有MP3)(GRILL:SIL.877C)
18-205P02030191 H/TRANSFORMER EI41 230V HF-V41A51TM
19-011092200321 SPEAKER 3" 2W 8Ω W/SIL.CAP #ABCADH1xx
19-200300000120 CONDENSER MIC DIA=10mm(-58DB BLUE)
20-11P020500010 V/CASS DECK CS-21V-205
20-70DA11000520 CD MECHANISM (SANYO) DA11B3V (BALL TYPE)
26-016100750121 E.CAP 100UF 16V +-20% MD "+" "-" 极
32-01CD31800020 ROD ANTENNA 158~600mm #6158
32-042162120020 FERRITE CORE 16x12mm H=8mm
41-061120070020 LEAF SWITCH TC-48021-01
26
43-520300000001 AC SOCKET (TAI CHUNG)TC08-115-02 VDE APP
44-022280066020 16P FLAT FLEX CABLE 1mm L=80mm (AA)
44-022315067020 17P FLAT FLEX CABLE 1mm L=150mm(INVERSE) >FOR DISPLAY
44-110316002520 JUMPER WIRE UL1007#26 4+152+4mm (RED) >FOR AC SWITCH TO PCB
44-110318002520 JUMPER WIRE UL1007#26 4+172+4mm (RED) >FOR B"+" TO AC SW.FM ANT
44-110325000520 JUMPER WIRE UL1007#26 4+242+4mm (BLACK) >FOR B- TO PCB
44-315310052620 2P WIRE L=100mm HSG(2)x1 (UL1007#28) >FOR CD DOOR
44-315337054520 4P WIRE L=220/370x2mm HSG(2)x1(UL1007#26 >FOR SPK
44-316315054520 4P WIRE L=150x2/260x2 HSG(2.5)x1 >CASS MOTOR
44-365315052620 2P SHIELD WIRE L=150mm HSG(2)x1 >FOR MIC
44-365318053620 3P SHIELD WIRE L=180mm HSG(2)x1(BLACK) >FOR CASS DECK
44-515312056620 6P WIRE L=120mm HSG(2)x2 (UL1571#28)(AB) >CD DECK
57-082122240020 PVC PLATE (BLACK) 12x24x0.3mm REAR CAB BATTERY BOX
57-083102200020 PVC PLATE (BLACK) 100x20x0.3mm FOR MAIN PCB
58-09CV10000020 CABLE TIE 2.5mmx4
58-192502500020 FELT 5x5x0.5mm W/TAPE STOP/BAND KNOB ;SKIP/TUNON KNOB
58-193900000020 FELT (W/TAPE 90x5MM) 90x5x0.5MM FOR FRONT CAB
58-263122200120 HARD RUBBER FOOT(PORON) DIA12mm T=2mm
58-422853130120 MIC CUSHION #BO8 DIA 8.5x13x9MM(BLACK)
58-583103100020 HARD RUBBER 10x10x5mm(W/10x10mm) FOR DISPLAY PCB x1
58-583153100120 HARD RUBBER 15x10mmW/TAPEx1 15x10x2 SPK
58-58A180000120 RUBBER CUSHION 10x20x1.5mm AM ANT
58-61A150002120 SHOCK ABSORBER(RED)(SOFT TYPE 30C AC210)
58-61A150005120 SHOCK ABSORBER(GREEN)HARD TYPE 40C AC220
58-63P020500020 FERBIE PLAITE 85.x90mm
58-63P020600020 SHIELDING PLATE-MAIN PCB
58-653190000120 SILVER CAP DIA 19MM
58-82P020300020 SPONGE 100x93x7mm W/TAPE(100x93mm) x1
58-82P020500020 SPONGE D28xD90xT10mm SPK
61-26P020300020 BATTERY SPRING "+" (DIA:0.8mm)
61-26P020300120 BATTERY SPRING "-" (DIA:0.8mm)
61-26P020300221 BATTERY SPRING/A "+/-" (DIA:0.8mm)(R1)
61-26P020300321 BATTERY SPRING/B "+/-"(DIA:0.8mm)(R1)
61-873318000020 LUG (SOLDERING) >FOR FM ANT
61-902680000020 SPEAKER CLIP
61-91P02050A120 SPEAKER GRILL -L (SIL.877C)
61-91P02051A120 SPEAKER GRILL -R (SIL.877C)
61-97P020300120 CD DOOR SPRING
61-97P020400020 CASS DOOR SPRING
66-120330160321 MACHINE SCREW MS/PH 3x6mm FOR FM ANT TO TOP CAB x1
66-140220212321 SELF-TAPPING SCREW TA/BH 2x12mm >FOR CD SWITCH TO TOP CAB x1
66-140230210321 SELF-TAPPING SCREW TA/BH 3x10mm >FOR CASS GEAR HOLDER TO FRONT CAB x2; SPK CLAMP/L TO FORNT CAB x2;
66-140230210321 SELF-TAPPING SCREW TA/BH 3x10mm >FOR SPK CLAMP/R TO FRONT CAB x2;HANDLE SHAFT/L TO TOP CAB x2;
66-140230210321 SELF-TAPPING SCREW TA/BH 3x10mm >FOR HANDLE SHAFT/R TO TOP CAB x2; SPK FIXTURE/L&R TO FRONT CAB x2;
66-140230210321 SELF-TAPPING SCREW TA/BH 3x10mm >FOR FRONT CAB TO TOP CAB x2; BOTTOM CAB TO FRONT CAB x2
66-140230210321 SELF-TAPPING SCREW TA/BH 3x10mm MPEG BD TO FRONT CAB x1
66-140230216321 SELF-TAPPING SCREW TA/BH 3x16mm >FOR REAR CAB TO TOP CAB x8;
66-140330210321 SELF-TAPPING SCREW TA/PH 3x10mm >FOR CASS DECK x4; MAIN PCB TO TOP CAB x4; BASS PCB TO TOP CAB x2;
66-140330210321 SELF-TAPPING SCREW TA/PH 3x10mm >FOR AC PRESS PIECE TO TOP x2;
66-140830180321 SELF-TAPPING SCREW TA/WH 3x8mm CASS SPRING TO FRONT x1;
66-140830210321 SELF-TAPPING SCREW TA/WH 3x10mm >FOR CD GEAR HOLDER TO TOP CAB x1; TF TO BOTTOM x2;
66-150330160321 SELF-TAPPING SCREW TB/PH 3x6mm FOR CONTROL PCB TO CASS DOOR x4;
66-150330180321 SELF-TAPPING SCREW TB/PH 3x8mm REMOTE PCB
66-151426216221 SCREW TWP/BO 2.6x16 MC >FOR CD DECK TO DECK BKT x4
66-170220160121 HARDEN SCREW TT/BH 2x6mm(BLACK) >FOR RECRODER ARM TO CASS DECK x1
68-122301600400 FIBRE WASHER 3x6x0.4mm CASS DECK x2;FM ANT PLATE x1;DIS PCB x1;CASS DOOR x4
68-122301800800 FIBRE WASHER 3x8x0.8mm FOR FIBER PLATE x3; MAIN PCB x1
68-122301801000 FIBRE WASHER 3x8x1mm FOR FIBRE PLATE
77-40P020300020 FUSE LABEL "F2AL 250V" 8x3mm
07-A10000020100 INDIRECT MATERIAL-通用遥控装配
79-290106330000 LOW TEMPERATURE MASKING TAPE 1/4"(S/N:A7
79-340112730000 P.P TAPE 1/2" (S/N:A26)
79-460101030000 SOLDER WIRE 50% DIA 1.0mm(S/N:B7)
79-680203530000 GLUE (YELLOW) #BY-883A (S/N:B26)
79-730301540000 SOLVENTS #BY-12B(S/N:B44)
79-730402040000 SOLVENTS #880A (S/N:B47)
07-P02030020020 INDIRECT MATERIAL-CASING (有MP3)
79-280106330000 DOUBLE FACE TAPE 1/4" (S/N:A2)
79-290106330000 LOW TEMPERATURE MASKING TAPE 1/4"(S/N:A7
79-290112730000 LOW TEMPERATURE MASKING TAPE 1/2"(S/N:A8
27
79-290125430000 LOW TEMPERATURE MASKING TAPE 1" (S/N:A10
79-300119030000 PVC INSULATING UL TAPE(BLACK)19mmS/N:A23
79-310112730000 THREAD SEAL TAPE(3M) 1/2"(S/N:A32)
79-340112730000 P.P TAPE 1/2" (S/N:A26)
79-340163530000 P.P CARTON SEALING TAPE 2.5" (S/N:A28)
79-380130440000 PROTECTIVE FILM 12"(S/N:A40
79-460101030000 SOLDER WIRE 50% DIA 1.0mm(S/N:B7)
79-540101030000 DAMPING GREASE #G-330(S/N:B38)
79-540502030000 DAMPING GREASE #0868G(S/N:B15)
79-570101030000 SI-LUBRICANTS #EM-50L (S/N:B37)
79-650100000000 HOTMELT STICK DIA11x30mm(30g)(S/N:B57)
79-680203530000 GLUE (YELLOW) #BY-883A (S/N:B26)
79-680403530000 GLUE #883 (S/N:B60)
79-680501030000 GLUE #1A-34 (S/N:B30)
79-681101030000 GLUE (RED) #SL-515 (S/N:B28)
79-730301540000 SOLVENTS #BY-12B(S/N:B44)
07-P02050011000 INDIRECT MATERIAL-PCB (有MP3)
79-280112730000 DOUBLE FACE TAPE 1/2" (S/N:A4)
79-290306330000 HIGH TEMPERATURE MASKING TAPE1/4"S/N:A52
79-290312730000 HIGH TEMPERATURE MASKING TAPE1/2"S/N:A53
79-460101030000 SOLDER WIRE 50% DIA 1.0mm(S/N:B7)
79-460401030000 SOLDER WIRE 60% DIA 1.0mm
79-480206320000 SOLDER BAR 63% (S/N:B2)
79-510105030000 HEATSINK GREASE (S/N:B22)
79-620204830000 WAX LOW TEMPERATURE #BAOYE(S/N:B11)
79-650100000000 HOTMELT STICK DIA11x30mm(30g)(S/N:B57)
79-680203530000 GLUE (YELLOW) #BY-883A (S/N:B26)
79-730201540000 THINNER #680 (S/N:B50)
79-730502040000 SOLVENTS #880H (S/N:B48)
79-730701540000 ROSIN NO CLEAN FLUX #1008A (S/N:B49)
08-P02055110010 PLASTIC ASS'Y "UNITED" (SILVER) (A-3)
56-01P02030B000 VOLUME KNOB ADAPTER (ABS)
56-02P02030A030 TOP CABINET (HIPS) (SIL.TN8-7)
56-03P02030A000 BOTTOM CABINET (HIPS) (SIL.TN8-7)
56-04P02050A020 FRONT CABINET (HIPS) (SIL.TN8-7)
56-06P02030A000 BATTERY DOOR (ABS) (SIL.TN8-7)
56-07P02050G000 DISPLAY RING (ABS) (CHROME)
56-07P020520000 CASS GEAR HOLDER (ABS)
56-07P020530000 CD GEAR HOLDER (ABS)
56-07P020548000 CASS DOOR BRACKET (ABS)
56-07P02055G000 CD DOOR RING (ABS) (CHROME)
56-13P02050A020 CASS DOOR (ABS) (SIL.TN8-7)
56-14P02050A030 CD DOOR (ABS) "UNITED" (SIL.TN8-7)
56-15M520R0B000 LASER COVER (FOR SANYO CD)
56-24P020500000 GEAR (ABS)
56-41P02030A000 HANDLE (ABS) (SIL.TN8-7)
56-41P02031A000 HANDLE COVER (ABS) (SIL.TN8-7)
56-53P02050G000 CD KNOB GROUP-L -3KEY (ABS) (CHROME)
56-53P02052G000 CD KNOB -PROGRAM (CHROME)
56-53P02053G000 CD KNOB GROUP-R -4KEY (ABS) (CHROME)
56-54P02030A000 VOLUME KNOB (ABS) (SIL.TN8-7)
56-54P02031A000 FUNCTION KNOB (ABS) (SIL.TN8-7)
56-54P02032A000 BASS KNOB (ABS) (SIL.TN8-7)
56-55P02030A000 CASS KNOB -6KEYS (ABS) (SIL.TN8-7)
56-57P020500020 DISPLAY LENS (SAN)
56-57P020510010 CD DOOR LENS (SAN)
56-57P020521010 REMOTE LENS (SAN)
56-60P02030B000 RECORDER ARM (ABS)
56-69P02030B000 AC PRESS PIECE (ABS)
56-69P02031B000 SPRUE COVER PIECE (ABS)
56-79P02030B000 HANDLE SHAFT/L (ABS)
56-79P02031B000 HANDLE SHAFT/R (ABS)
56-81000000B000 AC SOCKET COVER (ABS)
56-86P020500000 SPK FIXTURE/L (ABS)
56-86P020510000 SPK FIXTURE/R (ABS)

28