0% found this document useful (0 votes)
19 views

GWP

The document outlines the installation prerequisites, operational procedures, and maintenance guidelines for the EDEN WS water purifier. It emphasizes the importance of using a trained technician for installation, ensuring proper water quality and pressure, and regular cleaning of the storage tank. Additionally, it details the purification process, technical specifications, and warranty terms for the product.

Uploaded by

Karan Virbhadre
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
19 views

GWP

The document outlines the installation prerequisites, operational procedures, and maintenance guidelines for the EDEN WS water purifier. It emphasizes the importance of using a trained technician for installation, ensuring proper water quality and pressure, and regular cleaning of the storage tank. Additionally, it details the purification process, technical specifications, and warranty terms for the product.

Uploaded by

Karan Virbhadre
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

EDEN WS

PREREQUISITES FOR INSTALLATION


Product installation should be done only by a trained Eureka Forbes Service Technician only.
1. Input water must be tested for Total Dissolved Solids (TDS) and Total Hardness
- Install the product in a dry ventilated place. Keep it away from direct sunlight, heating devices or areas below 10oC.
- The purifier should be placed in area which is free of ants/insects/other pests.
- Ensure that the input tap water temperature is in the range of 10o - 40oC. Avoid installation to a hot water tap as it can damage the filters.
2. The input water pressure to your water purifier should be within the recommended range (refer variant specific technical specifications table). If the input
water pressure is more than specified, installation of a PRV (Pressure Regulating Valve)** is mandatory. If the input water pressure is less than specified,
installation of an external booster pump** is recommended.
3. Ensure that the filters are flushed thoroughly and independently for 3-5 minutes to remove fine particles present in the filter, before the installation of the
unit.
4. After installation, run the purifier for 5-10 minutes and drain the water.
Input water quality usage limitations:
1. If the input water iron content is more than that prescribed in the technical specifications, use of an iron remover** is recommended as a pre-treatment.
2. If the input water turbidity is more than that prescribed in the technical specifications or comprises colloidal particles, use of a special filter** is required
as a pre-filter.
3. If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer** is
recommended (applicable only for RO variants).
4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications.
**Available at an extra cost.
MTDS REGULATOR (Taste adjuster) OPERATING PROCEDURE

TDS modulator is located inside the product. As per factory setting, it comes in fully closed mode. TDS level of output water
can be increased by slowly loosening the spindle of the TDS modulator (anticlockwise). Normally a slight quarter turn is
enough to increase the TDS of the output water. Rotating the spindle in the clockwise direction closes the TDS modulator and
reduces the level of TDS blending.

Please note that the TDS blending, and its adjustment is dependent upon the level of TDS of input water and on the TDS
reduction capacity of the RO membrane. TDS adjustment should be done by the authorized Eureka Forbes technician only.
THE PROCESS OF PURIFICATION (For RO+UV+MTDS Variant)
Stage Treatment Materials Benefits
Multi-layered Polypropylene Roving
1 i-Filter Removes fine suspended particles such as dust, dirt mud and sand from water.
Wound Cartridge

Dust-free Bacteriostatic Activated


2 Chemi-Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour from the water.
Carbon Block

Membrane Life Prevents scaling of dissolved salts on the surface of the membrane, thereby, enhancing the membrane
3 Special Anti-scalant Media
Enhancer*** life and performance.

High recovery Reverse Thin Film Composite (TFC) Reverse Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates micro-
4
Osmosis Membrane Osmosis Membrane organisms like bacteria, viruses, protozoa and cysts.

UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa,
5 UV e-boiling Germicidal UV Lamp
thereby, making it safe to drink.

Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties that
help to support healthy metabolism. It also helps to provide the body with energy and is much needed
Active Copper A patented bacteriostatic taste for growth and development. Zinc also has a major role in the immune system. The activated carbon
6 with Zinc Booster enhancer with double goodness of removes organic components and polishes the water, giving it a sparkling look, making it pure and
Cartridge* Active Copper and Zinc Technology great to taste.
*Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification (Acceptable
limit)

7 TDS Regulator Manual taste adjusting system Adjusts the TDS of purified water to provide healthy water always.

***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L).
Available at extra cost.
TECHNICAL SPECIFICATIONS*
*Technical Specifications are subject to change without prior notice.
# Parameter Specification
1 Model AG EDEN WS RO+UV+MTDS+SS Note: The performance data presented in the table is applicable under standard
PRODUCT SPECIFICATION laboratory conditions#. Actual performance may vary depending on the input water
1 Dimension (W X D X H) 350 mm X 275 mm X 530 mm quality, water pressure and condition of filters.
2 Net Weight 8 kg (Approx.) **If the pressure is higher than the maximum specified, use of a pressure regulating
3 Purification Technology RO+UV +MTDS valve is mandatory.
4 Tank Capacity 5.0 Liters (Approx.)
The above accessories are available with our company at an additional cost.
i-Filter, Chemi-Block, High recovery
Reverse Osmosis Cartridge, UV e-boiling, The purification cartridges are designed to provide safe water for a period of 1 year or
5 Standard Purification supplied
Active Copper with Zinc Booster 6000 litres# from the date of installation. Post the safe life, for your complete
Cartridge, TDS Regulator protection, it is recommended to replace cartridges.
ELECTRICAL SPECIFICATIONS
Performance data sheets are available with Eureka Forbes Technical Documentation
1 Power Rating 45 Watts (max.)
Centre.
2 Power Supply Input - 230V AC, 50 Hz.
3 Operating Voltage Range 150 VAC to 250 VAC, 50 Hz Warranty void if the product is not installed as per recommendations.
5,000 burning hours (as per UV lamp #Standard Test Conditions:
4 UV Lamp Life
manufacturer spec.)
Feed Water Quality: TDS Max: 750 mg/litres with NaCl Pressure: 1.0 kg/cm2,
RECOMMENDED INPUT WATER PARAMETERS
Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron:
1 Input Water Pressure Range** Up to 3.0 kg/cm² below 0.1 mg/litres. Pressure on membrane: 95psi. Product Recovery @ 40%.
2 Iron Content (Max.) 0.1 mg/L Depending on the input water quality (variations in the standard test conditions) the
3 Chlorine Content (Max.) 0.2 mg/L filter might need a replacement even before the claimed life.
4 Input Water Turbidity (Max.) 5 NTU #Actual performance may vary based on the input water conditions - TDS, Hardness,
5 Total Dissolved Solids (TDS) (max.) Up to 2,000 mg/L Pressure, Temperature & pH. Standard test Condition are valid for online water
6 Total Hardness (max.) 600 mg/L supply installation. In suction mode, the product performance may be lower than
CONSUMABLES the claims.
i-Filter, Chemi-Block, High recovery Reverse Osmosis Cartridge, Active Copper with Zinc
Booster Cartridge
FUNCTION OF INDICATORS – LED DISPLAY

LEDs GREEN BLUE RED Remarks


Power Tank Call Service
PARAMETERS
(GREEN) (BLUE) (RED)
Red and Blue will glow for 0.25s one after the other for 3 secs. Green
Power ON Solid ON Blinks Blinks LED will be ON as long as product has power. Applicable for RO+UV,
RO & UV models
Blinks 30 seconds for UV models & Blinks 6 seconds for RO+UV
Pre Purification time Solid ON Blinks Six Times OFF models
Tank Filling Mode Solid ON Blinks Once OFF Applicable for RO+UV, RO, UV models

Storage Tank Full Mode Solid ON Solid ON OFF Applicable for RO+UV, RO, UV models

No water/Low water Input Solid ON Blinks Thrice OFF Applicable for RO + UV , RO & UV models.

UV Lamp Fault Solid ON OFF Solid ON Applicable only for RO+UV and UV models

EA Fault Solid ON OFF Blinks Once Applicable for RO+UV, RO, UV models
Filter Tampered / Partially Used
Solid ON OFF Blink Twice Applicable for RO+UV, RO, UV models
Filter
SV / Pump Fault Solid ON OFF Blinks Six Times Applicable for RO+UV, RO, UV models
CLEANING AND DISINFECTION OF WATER STORAGE TANK

Note: Storage tank of this product must be periodically (at least once in every 30 days) cleaned by a disinfectant.
Disinfection Tablets may be purchased from the company authorised Service Centre. Please follow the disinfection process
strictly as per the instructions as provided in this User Manual.

1. Switch OFF the water purifier from the main power supply.
2. Drain the tank completely.
3. Open the top cover, wipe the inside of the tank with a dry, clean soft cloth.
4. Keep the top cover in place.
5. Switch the power supply ON.
6. Let the storage tank gets filled and then drop one Disinfection Tablet* into the tank.
Caution: Keep the Disinfection Tablets out of the reach of children. Do not eat/consume the tablet.
7. Keep the top cover in place and leave the unit for 30 minutes.
8. After 30 minutes, open the tap and discard this and the first filling water completely. Caution: Do not drink this
water.
9. Now your unit is ready to use. In case you notice any medicinal taste/smell, discard the tank of water fully & let it refill
again.
10. Please ensure that this disinfection process is carried out by the authorised installation person/service technician during
first installation and in every subsequent mandatory servicing of the product.

*Available with Eureka Forbes Service Technician


RECYCLE WATER AND ITS REUSE

Water is a rapidly depleting resource. It is our moral responsibility to ensure that water is recycled as much as possible.

Flushed out water from a RO system is an unavoidable technology limitation. It maintains the performance of the purification process and
the service life of the membrane also. Eureka Forbes has taken utmost care to minimize the water wastage in our RO system without
compromising on the performance of the product.

The water flushed out by your Aquaguard RO Water Purifier can be collected and used for several purposes.

Flushed Water can be used for :

Daily household cleaning


Watering tasks like mopping floors,
plants cleaning bathrooms,
kitchen sinks, etc.

Flushed Water cannot be used for :

Drinking Washing clothes


A QUICK CHECKLIST

Problems Checkpoints Solutions


Water tastes bad 1. Is the tank clean? 1. Clean the storage tank.
2. Have you kept the purified water in 2. Dispose of water and clean the tank.
the tank for too long? 3. Call an authorised Eureka Forbes Service
3. Is it time to change the filter? Technician.
Less water has been purified 1. Is the tap water valve closed? 1. Open the tap water valve.
2. Is the tap water pressure too low? 2. If so, the amount of purified water will be
3. Filters may be clogged or damaged reduced.
3. Call an authorised Eureka Forbes Service
Technician.
Water doesn’t flow into the 1. Is there water available in the 1. Ensure the overhead tank is filled with water.
storage tank overhead tank? 2. Ensure the tap is open.
2. Is the main water supply tap closed? 3. Call an authorised Eureka Forbes Service
3. Not sure what is wrong? Technician.
Water is leaking 1. Is water coming out of the top of the 1. Close the tap water valve, unplug the power
purifier? cord, and call an authorised Eureka Forbes
Service Technician.
IMPORTANT NOTE ON ZERO PRESSURE PUMP (ZPP)

Your Aquaguard is equipped with a unique pump having both suction and boosting capabilities and comes with specially designed sensing system. Now, this
enables your Aquaguard to work in the following operating conditions:-
1. Normal Input Water Pressure – up to 3 Bar (max.)
2. Low Water Pressure from Loft Tank.
3. Zero water pressure.
4. Suction mode: Maximum 1 m below product level.

Product functioning at “Normal / Low and Zero water Pressure”:


• Ensure that the water flow from the tap into the product is always more than 1.5 LPM.
• In case there is no incoming water supply, the sensing system detects unavailability of water and stop the unit from working to prevent dry running.
• The intelligent mechanism in your Aquaguard will keep on checking the availability of water at regular defined intervals and make the product work as and when
water supply resumes.
Note: In case you notice that water in the supply line resumes and product is in stand-by mode, then please restart the product by switching OFF and ON
the power supply.
Product Functioning with “Suction Capability”:
1. Whenever the water in the container/ bucket gets over and bucket gets empty, the sensing system detects non water availability and stops the product from
functioning. Note: When container/ bucket is refilled with water, the product should be restarted by switching the power supply OFF and ON again.
2. Prolonged use in loft tank mode /suction mode can impact the working of pump, performance of product and life of filters. If the performance is not meeting the
flow requirement due to low input pressure, then use of an external booster pump is highly recommended.”
3. Do not re-circulate / reuse the rejected water (discharged by the product) back into the product.
4. The booster pump in your Aquaguard also has the capability of suction of water from a 1 m distance below the level of product i.e. it can pull water from a
bucket / container. Note: It is not suitable for suction of water from underground storage tank, sump, open well etc. where the water level is beyond 3 feet below
the level of product.
WARRANTY TERMS & CONDITIONS*

1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original purchase.
2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized agent adequate opportunity to inspect test and remedy them for
which the Customer will deposit the goods at its own expense, if so, required by the Company with the Company's Office/Service Centre along with the original invoice in the city where
they are sold.
3. The Inspection and Test Report of the company's office/service centre will be final and binding under the warranty for determining defects, repairs / alterations required or carried out or
certifying work of the goods thereafter.
4. Aquaguard may require initial setting, post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the
company's service centre.
5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty.
6. Notwithstanding anything to the contrary contained or implied by this warranty:
a) The company's liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the
customer.
b) The company's liability under this warranty shall be limited only to defects in the goods which occur under the conditions of normal operation of the goods and their proper and prescribed
use. The warranty does not cover or extend to defects which are determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse,
misuse, faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or
damage caused by lightening or other electrical disturbances or interruptions, dismantling or re-installation at a different location.
c) The company's liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorized agency at the location specified in the invoice and such
installation is undertaken by the company or its authorized agent or franchisee.
d) Consumable items are subject to normal wear and tear are not covered by this warranty. Please refer model specific components given in the technical specifications table.
e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installation, on the condition that the input water is as per the standard
test conditions for RO variants (provided in the section “Technical specifications table”), mentioned in the user manual. If the RO membrane gets clogged within warranty period, it will be
cleaned/repaired/replaced free of charge as deemed fit by the company authorized service person/centre after inspection. (At applicable for RO models only.)
f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or pursuant to this warranty in respect of death or injury to the customer
or any other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than in
accordance with the user manual or by due to any other cause or circumstances beyond the control of the company.
WARRANTY TERMS & CONDITIONS*

g) The company's liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the customer to the company for the goods stated in the invoice.
General
For the purpose of this warranty, the following expressions shall have the following meanings respectively:
1. The 'Goods' shall mean the goods described in the Order Form.
2. The 'Customer' shall mean the original purchaser of goods from the company.
3. The 'Company' shall mean EUREKA FORBES LIMITED.
4. Aquaguard means and includes Aquaguard , Aquaguard Select and Sure from Aquaguard .
5. 'General Terms & Conditions' shall mean the terms and conditions agreed upon by the customer and the company printed on the Order Form.
6. 'Invoice' shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the total purchase price thereof and name of the customer.
7. 'User Manual shall mean the instructions for Installation, use and maintenance provided through QR code along with Product supplied by the company.
8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time to time without any prior notice.
9. Any disputes are subject to Mumbai Jurisdiction only.
Post-warranty
1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms.
2. In case the customer does not wish to enter the Service Contract, he has the option of calling the company's service centre having his Aquaguard services on an actual basis, i.e., by
paying the labour cost and spares needed to attend to that service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places
where the company has its service centres.
3. If during such servicing it is necessary for the company to replace or repair defective components or parts, the customer shall be required to pay for the same as per the company's
prevailing price list.
4. Eureka Forbes limited reserves the right to offer annual maintenance contract/ensure availability of spares only up to 7 years from the date of invoice.
*Conditions apply.
WARRANTY TERMS & CONDITIONS*

Lifetime warranty on Stainless Steel Tank:


Terms & Conditions for Life time Stainless Steel tank warranty:
a) Usage under recommended input water condition with regular maintenance by EFL authorized Service Centre. This warranty covers
Stainless Steel Tank only. Lifetime refers to the 'life of the water purifier' (life of the water purifier is 7 years from the date of invoice, please
refer to Point 4 under “Post warranty”.)
b) Lifetime warranty of Stainless-Steel tank is only applicable if the tank is used as a part of product assembly for storing purified water. In-
case of any claims arising out of defects or leakage, the tank will be repaired or replaced free of cost as per the company guidelines however
service visit charges need to be paid by customers as per the prevailing rates.
c) The warranty is only valid if the tank is periodically cleaned as per the recommendations in the user manual.
d) The warranty is not applicable in-case the product is used for any non-residential purposes.
e) This warranty T&Cs are limited to Stainless Steel Tank and shall not be clubbed with other prevalent warranty T&Cs.

*Conditions apply.
ENVIRONMENT PROTECTION:
"Protection" has always been our motto and guiding principle. We care for the environment. We urge you to recycle the packaging material or
take it to the nearest recycling facility rather than dispose it off with the rest of your waste. Your product has been designed to work for many
years, however, should you wish to upgrade or replace your old product, remember to help protect the environment by disposing it off at your
local e-waste disposal center. Should you have any queries, the nearest authorized service center of Eureka Forbes will be able to guide you.
Allow us to become your environment partner; together we can make the world a cleaner place.

HEALTH PROTECTTM
For your safety the specially designed and electronically authenticated purification cartridges of Aquaguard ensure our promise of 'pure &
healthy water always. In the unlikely usage of a 'non-genuine' purification cartridge that could potentially deliver unsafe water - an indication
light will draw your attention. For your complete protection, it does not initiate the purification process. The purification cartridges are designed
to provide safe water for a period of 1 year or 6000 litres# from the date of installation. Post the safe life, for your complete protection, it is
recommended to replace cartridges.

#StandardTest Conditions. Depending on the input water quality (variations in the standard test conditions) the filter might need a
replacement even before the purifier gives you an alert.
ENVIRONMENT PROTECTION:
"Protection" has always been our motto and guiding principle. We care for the environment. We urge you to recycle the packaging material or
take it to the nearest recycling facility rather than dispose it off with the rest of your waste. Your product has been designed to work for many
years, however, should you wish to upgrade or replace your old product, remember to help protect the environment by disposing it off at your
local e-waste disposal center. Should you have any queries, the nearest authorized service center of Eureka Forbes will be able to guide you.
Allow us to become your environment partner; together we can make the world a cleaner place.

HEALTH PROTECTTM
For your safety the specially designed and electronically authenticated purification cartridges of Aquaguard ensure our promise of 'pure &
healthy water always. In the unlikely usage of a 'non-genuine' purification cartridge that could potentially deliver unsafe water - an indication
light will draw your attention. For your complete protection, it does not initiate the purification process. The purification cartridges are designed
to provide safe water for a period of 1 year or 6000 litres# from the date of installation. Post the safe life, for your complete protection, it is
recommended to replace cartridges.

#StandardTest Conditions. Depending on the input water quality (variations in the standard test conditions) the filter might need a
replacement even before the purifier gives you an alert.

You might also like