Dry-film lubricant
coatings
Delivering corrosion resistance and Suggested markets
low coefficients of friction for fasteners
General industrial fasteners
Available in a range of formulations, PPG XYLAN® dry-film
Protective and marine coatings
lubricant topcoats are ideally suited for fasteners used in energy,
petrochemical and water treatment applications. Applied over
pretreated or primed metal surfaces, these coating systems are
available in both solvent- and water-based formulas, offering a unique
combination of low coefficients of friction and resistance to abrasion,
chemicals and extreme temperatures.
When applied over our proprietary PPG XYLAR® ceramic primers,
the Xylan topcoats listed on the reverse side are rated for over
5,000 hours of salt spray corrosion performance. Specific
formulations, coupled with other types of pretreatments or primers,
allow for a full range of performance and temperature options.
Unique benefits
• Low coefficients of friction • Solventborne and waterborne
that reduce and improve the options
uniformity of make-up torque • Compatible with zinc phosphate
• Outstanding corrosion and pretreatment, zinc or zinc-nickel
abrasion resistance plating, and Xylar primers
• Ability to specify systems • Extreme temperature options
ranging from 500 to over 5,000
hours of corrosion resistance
Performance Features Xylan 1070 Xylan 1400 Xylan 1424 Xylar
and Properties Test Standard Coating 1 Coating 1 Coating 1 Primer
Formulation - Solventborne Solventborne Waterborne Ceramic
Corrosion Resistance
with Zinc Phosphate > 500 hours > 1,500 hours > 1,500 hours N/A
with Zinc Plating ASTM B117 > 1,500 hours > 2,500 hours > 2,500 hours N/A
with Zinc-Nickel Plating > 3,000 hours > 4,000 hours > 4,000 hours N/A
with Xylar Primer 2 > 5,000 hours > 5,000 hours > 5,000 hours N/A
Coefficient of Friction3 ASTM G99 0.05 – 0.12 0.05-0.31 0.05 – 0.09 0.11 – 0.13
-319 – 500˚ F -4 – 374˚ F -58 – 347˚ F -40 – 995˚ F
Working Temperature Range3 -
(-195 – 260° C) (-20 – 190° C) (-50 – 175° C) (-40 – 535° C)
15 – 25 μm / 15 – 25 μm / 15 – 25 μm / 15 – 30 μm /
Dry-Film Thickness3 ASTM D1186
0.6-1.0 mils 0.6-1.0 mils 0.6-1.0 mils 0.6-1.2 mils
Adhesion3 ASTM D3359 >3B >3B >3B >3B
Film Hardness3 ASTM D3363 2H - 4H 2H - 3H 2H - 3H >3H
Impact3 ASTM D2794 Pass Pass Pass N/A
1
These Xylan products represent a typical range of options for fastener coatings. Please contact your PPG representative for additional options and information.
2
Data based on 0% RR (Industry standard failure = 15% RR)
3
Tests were performed using grit-blasted carbon steel panels with a surface profile of 1.5-3.5 μm (Ra). For additional application information, please contact your
PPG representative or refer to product data sheets. Always use a capable or PPG-recommended applicator.
This document contains general information only and should not be construed as creating any warranties, express or implied.
Please contact a PPG representative for additional information.
The PPG Logo is a registered trademark and We protect and beautify the world is a trademark of PPG Industries Ohio, Inc. Xylan and
Xylar are registered trademarks of the PPG Group of Companies. The IN Logo is a registered trademark of LinkedIn Corporation.
©2023 PPG Industries, Inc. All rights reserved. 08/23 IC129
PPG Industrial Coatings • One PPG Place, Pittsburgh, PA 15272 • 1.888.774.2001 • ppgindustrialcoatings.com
