Smart 700 IE V4, Smart 1000 IE V4

Preface

Overview 1

Safety instructions 2
SIMATIC HMI
Mounting and connecting 3
HMI devices
Smart 700 IE V4, Smart 1000 IE V4 4
Operating the device

Configuring the device 5

Operating Instructions

Commissioning a project 6

Maintenance and care 7

Technical specifications 8

Technical Support A

Abbreviations B

12/2023
A5E51638950-AC
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens Aktiengesellschaft. The remaining trademarks in
this publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens Aktiengesellschaft A5E51638950-AC Copyright © Siemens 2023.

Digital Industries Ⓟ 02/2024 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Preface

Purpose of the operating instructions

These operating instructions provide information based on the requirements defined by
IEC 62079 for documentation. This information relates to the HMI device, its storage,
transportation, place of use, installation, use and maintenance.
These operating instructions are intended for a variety of target groups. The following table
shows the chapters of these operating instructions that are of particular importance for the
respective target group.

Target group Chapter

All "Safety instructions"
Operators "Overview"
The operator operates and monitors the system "Operating the device"
during the process control phase.
Commissioning engineers All chapters.
The commissioning engineer integrates the HMI Depending on the use of the HMI device,
device into the system and ensures the operating certain chapters may not be of relevance to the
capability of the HMI device for the process control commissioning engineer, e.g. the section
phase. "Maintenance and care."
Service technicians All chapters.
Service technicians rectify faults that occur during Depending on the use of the HMI device,
the process control phase. certain chapters may not be of relevance to the
service technicians, e.g. the section
"Maintenance and care."
Maintenance technicians Maintenance and care
Maintenance technicians carry out servicing and
maintenance work during the process control
phase.

The WinCC flexible Smart online help contains additional information. The online help
contains instructions, examples and reference information in electronic form.

Scope
These operating instructions apply to the following Smart HMI devices:

Product name MLFB number

SIMATIC HMI Smart 700 IE V4 6AV6648-0DC11-3AX0
SIMATIC HMI Smart 1000 IE V4 6AV6648-0DE11-3AX0

Note
The firmware version must be V4.0.2.0 and later versions.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 3
Preface

Basic knowledge required

Knowledge of automation technology and process communication is necessary to
understand the operating instructions.
An understanding of the use of computers and operating systems is also required.

Illustrations and text highlighting

This manual contains figures of the described devices. The figures may deviate from the
supplied device in certain details.
The following graphical highlighting facilitates reading these operating instructions:

Graphical highlighting Description

If the instructions involve
several tasks, the individual
tasks are highlighted by a red
number circle.

A light blue highlight indicates

components and tools that are
required in the course of a
task.

Smart 700 IE is sometimes

shown in the figures as a
representation of all Smart IE
Panels.

Smart 700 IE V4, Smart 1000 IE V4

4 Operating Instructions, 12/2023, A5E51638950-AC
 Preface

The following text highlighting facilitates reading these operating instructions:

Text highlighting Scope

"Add screen" • Terms that appear in the user interface, for example, dialog
names, tabs, buttons, menu commands
• Input values, for example, limits, tag values
• Path information
"File > Edit" Operational sequences, for example, menu commands, shortcut
menu commands
<F1> Keyboard operation

Note information highlighted as follows:

Note
A note contains important information on described products and their handling or on a
section of this documentation.

Names of the hardware

These operating instructions describe the Smart IE V4 HMI devices. The term "HMI device" is
used synonymously for a "Smart IE V4 HMI device" in these instructions.

Names of the software

Configuration and runtime software have different names as follows:
• "WinCC flexible Smart" refers to the configuration software used to create an HMI project.
• The term "runtime" refers to the "WinCC flexible Smart Runtime" software running on the
HMI devices.

Trademarks
Names labeled with a ® symbol are registered trademarks of the Siemens AG. Other names
used in this documentation may be trademarks, the use of which by third parties for their
own purposes could violate the rights of the owner.
• HMI®
• SIMATIC®
• SIMATIC HMI®
• WinCC®

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 5
Preface

History

Edition Comment
02/2022 First Edition
01/2023 Second Edition
Description of HMI panel user interfaces and related operations are updated.
12/2023 Third Edition
• Description of HMI panel user interfaces and related operations are updated:
– Remote password (Page 56)
– Network discovery (Page 53)
• Description of ID link (Page 75) is added.

Smart 700 IE V4, Smart 1000 IE V4

6 Operating Instructions, 12/2023, A5E51638950-AC
Table of contents

Preface ................................................................................................................................................... 3
1 Overview.............................................................................................................................................. 10
1.1 Product description ............................................................................................................ 10
1.2 Design of the HMI devices .................................................................................................. 11
1.3 Scope of delivery ............................................................................................................... 12
1.4 Accessories ........................................................................................................................ 12
2 Safety instructions ............................................................................................................................... 13
2.1 General safety instructions ................................................................................................. 13
2.2 Data protection.................................................................................................................. 15
2.3 Notes about usage ............................................................................................................. 15
3 Mounting and connecting ................................................................................................................... 18
3.1 Preparations ...................................................................................................................... 18
3.1.1 Checking the package contents .......................................................................................... 18
3.1.2 Checking the operating conditions ..................................................................................... 18
3.1.3 Selecting a mounting position ............................................................................................ 18
3.1.4 Checking clearances .......................................................................................................... 20
3.1.5 Making the mounting cutout ............................................................................................. 21
3.2 Mounting the HMI device ................................................................................................... 22
3.3 Connecting the HMI device ................................................................................................ 24
3.3.1 Connection sequence ........................................................................................................ 24
3.3.2 Connecting the equipotential bonding circuit ..................................................................... 25
3.3.3 Connecting the power supply............................................................................................. 28
3.3.4 Connecting the configuration PC ........................................................................................ 29
3.3.5 Connecting the PLC ............................................................................................................ 31
3.3.6 Connecting a USB device .................................................................................................... 32
3.4 Switching on and testing the HMI device ............................................................................ 34
3.5 Securing the cables ............................................................................................................ 35
4 Operating the device ........................................................................................................................... 36
4.1 Overview ........................................................................................................................... 36
4.2 General functions of the screen keyboard........................................................................... 37
4.3 The screen keyboards ........................................................................................................ 38
4.4 Entering data ..................................................................................................................... 39
5 Configuring the device ........................................................................................................................ 40
5.1 Opening the settings ......................................................................................................... 40
5.2 Overview ........................................................................................................................... 41

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 7
Table of contents

5.3 General functions in the Control Panel ............................................................................... 41

5.4 Functions for Service and Commissioning .......................................................................... 42
5.4.1 Backup .............................................................................................................................. 42
5.4.2 Restore .............................................................................................................................. 43
5.4.3 OS update ......................................................................................................................... 44
5.4.4 Project ............................................................................................................................... 45
5.5 Changing the Ethernet parameters..................................................................................... 46
5.6 Changing display orientation and startup delay time .......................................................... 48
5.7 Displaying information about the HMI device ..................................................................... 49
5.8 Calibrating the touch screen .............................................................................................. 50
5.9 Displaying licensing information for the HMI device ........................................................... 51
5.10 Setting the screen saver ..................................................................................................... 51
5.11 Enabling the Transfer channel ............................................................................................ 52
5.12 Enabling the Network Discovery ......................................................................................... 53
5.13 Activating the acoustic signal ............................................................................................. 53
5.14 Setting the date and time .................................................................................................. 54
5.15 Changing the password settings ........................................................................................ 54
5.15.1 Setting the device password .............................................................................................. 55
5.15.2 Setting the remote password ............................................................................................. 56
6 Commissioning a project ..................................................................................................................... 58
6.1 Overview ........................................................................................................................... 58
6.2 Operating modes ............................................................................................................... 59
6.3 Data transmission options .................................................................................................. 60
6.4 Transfer ............................................................................................................................. 60
6.4.1 Overview ........................................................................................................................... 60
6.4.2 Starting the manual transfer .............................................................................................. 61
6.4.3 Starting the transfer automatically ..................................................................................... 61
6.4.4 Testing a project ................................................................................................................ 63
6.5 Backup and restore ............................................................................................................ 64
6.6 Updating the operating system .......................................................................................... 65
7 Maintenance and care ......................................................................................................................... 66
7.1 Maintenance and care ....................................................................................................... 66
7.2 Recycling ........................................................................................................................... 67
8 Technical specifications ....................................................................................................................... 68
8.1 Certificates and approvals .................................................................................................. 68
8.2 Electromagnetic compatibility ............................................................................................ 69
8.2.1 Emitted interference .......................................................................................................... 69
8.2.2 Immunity to interferences.................................................................................................. 69
8.3 Mechanical ambient conditions .......................................................................................... 69

Smart 700 IE V4, Smart 1000 IE V4

8 Operating Instructions, 12/2023, A5E51638950-AC
 Table of contents

8.3.1 Transport and storage conditions ....................................................................................... 69

8.3.2 Operating Conditions ......................................................................................................... 70
8.4 Climatic ambient conditions ............................................................................................... 70
8.4.1 Transport and storage conditions ....................................................................................... 70
8.4.2 Operating Conditions ......................................................................................................... 71
8.4.3 Climate diagram ................................................................................................................ 71
8.5 Protection classes .............................................................................................................. 72
8.5.1 Insulation test .................................................................................................................... 72
8.5.2 Protection against foreign objects and water ...................................................................... 72
8.6 Dimension drawings .......................................................................................................... 73
8.6.1 Dimension drawing of Smart 700 IE V4 .............................................................................. 73
8.6.2 Dimension drawing of Smart 1000 IE V4 ............................................................................ 74
8.7 Rating plate ....................................................................................................................... 75
8.8 Technical data ................................................................................................................... 76
8.9 Ports description ................................................................................................................ 77
8.9.1 DC24V - X80 ...................................................................................................................... 77
8.9.2 PPI / RS422 / RS485 - X2 ..................................................................................................... 78
8.9.3 Ethernet (LAN) - X1 ............................................................................................................ 78
8.9.4 USB - X60 .......................................................................................................................... 79
8.10 Communication with PLCs.................................................................................................. 79
8.11 Scope of functions with WinCC flexible SMART ................................................................... 82
A Technical Support ................................................................................................................................ 86
A.1 Service and support ........................................................................................................... 86
A.2 System events ................................................................................................................... 86
B Abbreviations ...................................................................................................................................... 87
Glossary ............................................................................................................................................... 88
Index .................................................................................................................................................... 91

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 9
Overview 1
1.1 Product description

Optimal choice for simple applications - Smart Panel V4

Reliable new generation Smart Panel for small automation systems

Today, visualization is part of the standard repertoire for most machines. HMI devices with
basic functions are fully sufficient for small machines and simple applications.
This is exactly the demand that the Smart Panel intends to meet. By enhancing
functionalities, Smart Panel V4 goes on to offer exactly those basic features.
The scope of performance of the Smart Panel V4 has been expanded tremendously.
Enhanced CPU and Memory contribute to increase the performance. The additional USB Host
port is a significant interface improvement. The RTC real time clock with a maintenance-free
capacitor system and the improved touch display offer much better user experiences.
Configuration and operation of the new panels have become easier in connection with
simplified programming by means of the new Engineering Software - WinCC flexible Smart
V4.
For detailed technical information, please refer to chapter "Technical specifications
(Page 68)".

Smart 700 IE V4, Smart 1000 IE V4

10 Operating Instructions, 12/2023, A5E51638950-AC
 Overview
1.2 Design of the HMI devices

1.2 Design of the HMI devices

The figure below shows the design of the HMI devices using Smart 700 IE V4 as an example.

① Power supply connection ⑥ Display/touch screen

② RS 422/485 port ⑦ Mounting seal
③ USB port ⑧ Rating plate
④ Ethernet port
⑤ Recesses for a mounting clip

The Ethernet port can be configured via the Control Panel or the WinCC flexible Smart
software.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 11
Overview
1.3 Scope of delivery

The RS 422/485 port is configured via the WinCC flexible Smart software.

1.3 Scope of delivery

The scope of delivery of the HMI device includes the following components:

Name Figure Quantity

HMI device 1

1 OSS mini DVD

1 Accessory kit with According to the quantity required
mounting clips for mounting, in accessory kit

Power supply terminal 1, in accessory kit

1.4 Accessories
Accessories are not included in the HMI device scope of delivery, but can be ordered on the
Internet under Industry Mall (http://mall.industry.siemens.com).

Smart 700 IE V4, Smart 1000 IE V4

12 Operating Instructions, 12/2023, A5E51638950-AC
Safety instructions 2
2.1 General safety instructions

Working on the control cabinet

WARNING
The device constitutes open equipment on the back side
The device constitutes open equipment on the back side. This means that the device may
only be integrated in an enclosure or cabinet which provides front access for operating the
device. The enclosure, the cabinet or the electrical operating rooms must provide protection
against electric shock and the spread of fire. The requirements regarding the mechanical
strength must also be considered.
Access to the enclosure or cabinet in which the device is installed should only be possible by
means of a key or tool and for trained and qualified personnel.
Dangerous voltage
Opening the cabinet will expose high voltage parts. Contact with these parts could be fatal.
Always disconnect the cabinet from the mains before opening it.

High frequency radiation

Note
Unwanted operating states
High-frequency radiation, for example, from cellular phones, can trigger unwanted operating
states.

Installation as intended

WARNING
Installation only in machinery that conforms to the machinery directive
You are not permitted to commission the HMI device unless it has been verified that the
machine in which the HMI device is to be installed complies with directive 2006/42/EC.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 13
Safety instructions
2.1 General safety instructions

ESD
A device equipped with electronic components is an electrostatic sensitive device. Due to
their design, electronic components are sensitive to overvoltage and thus to the discharge of
static electricity. Note the corresponding regulations when handling ESD.

Industrial Security
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply latest updates may increase customer’s exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (https://www.siemens.com/cert).

Disclaimer for third-party software updates

This product includes third-party software. Siemens AG only provides a warranty for
updates/patches of the third-party software, if these have been distributed as part of a
Siemens software update service contract or officially released by Siemens AG. Otherwise,
updates/patches are undertaken at your own risk. You can find more information about our
Software Update Service offer on the Internet at Software Update Service
(http://www.automation.siemens.com/mcms/automation-software/en/software-update-
service).

Notes on protecting administrator accounts

A user with administrator privileges has extensive access and manipulation options in the
system.
Therefore, ensure there are adequate safeguards for protecting the administrator accounts to
prevent unauthorized changes. To do this, use secure passwords and a standard user account
for normal operation. Other measures, such as the use of security policies, should be applied
as needed.

Smart 700 IE V4, Smart 1000 IE V4

14 Operating Instructions, 12/2023, A5E51638950-AC
 Safety instructions
2.2 Data protection

Disclaimer
Please note that the above recommended risk-minimizing security measures are not intended
to be exhaustive. Therefore, please consult your security expert for final assessment and
configuration.

2.2 Data protection

Siemens observes the principles of data protection, in particular the principle of data
minimization (privacy by design). For this product SIMATIC HMI Smart 700/1000 IE V4, this
means: The product does not process / store any personal data, only technical functional data
(e.g. time stamp). If the user links this data with other data (e.g. shift plans) or stores
personal data on the same medium (e.g. hard disk) and thus establishes a personal reference,
the user must ensure compliance with data protection regulations.

2.3 Notes about usage

NOTICE
The HMI device is approved for indoor use only.
The HMI device may be damaged if it is operated outdoors.
Operate the HMI device indoors only.

Industrial applications
The HMI device is designed for industrial applications. It conforms to the following standards:
• Requirements of the emission standard for industrial environments, EN/IEC 61000-6-4
• ESD immunity requirements to EN/IEC 61000-6-2

Use in residential areas

Note
The HMI device is not intended for use in residential areas. Operation of an HMI device in
residential areas can have a negative influence on radio/TV reception.

If the HMI device is used in a residential area, you must take measures to achieve Limit Class
B conforming to EN 55011 for RF interference.
Individual acceptance is required.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 15
Safety instructions
2.3 Notes about usage

Use with additional measures

The HMI device should not be used at the following locations unless additional measures are
taken:
• In locations with a high degree of ionizing radiation
• In locations with severe operating conditions, for example, due to:
– Corrosive vapors, gases, oils or chemicals
– Electrical or magnetic fields of high intensity
• In systems that require special monitoring, for example, in:
– Elevators
– Systems in especially hazardous rooms

Notes on communication

Note
Communication errors caused by address conflict
Communication errors can occur if several devices in a network share the same bus address
or IP address.
Make sure that your HMI device is assigned a unique address in the network.

Note
Updating tag values following a communication error
If the communication between HMI device and PLC is interrupted, all tag values displayed on
the HMI device will be replaced by a hash mark ("#").
When the communication between the HMI device and the PLC is restored, all tag values will
be updated immediately. The cycle time for updating the tag values begins again at "0".

Note on secure boot

Secure boot is used to prevent malicious software from loading when Smart 700 IE/1000 IE
V4 starts up.

Smart 700 IE V4, Smart 1000 IE V4

16 Operating Instructions, 12/2023, A5E51638950-AC
 Safety instructions
2.3 Notes about usage

Secure boot is enabled in Smart 700 IE/1000 IE V4 by default. If you need to disable the
secure boot, please contact technical support.

Note
If secure boot is disabled, all factory defaults images in Smart 700 IE/1000 IE V4, projects and
user data are erased, and Smart 700 IE/1000 IE V4 can only run images generated by
yourself.
If secure boot is disabled, SIEMENS would not provide technical support and maintenance
service for the device.
If secure boot is disabled, you cannot enable the secure boot.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 17
Mounting and connecting 3
3.1 Preparations

3.1.1 Checking the package contents

Check the package content for visible signs of transport damage and for completeness.

Note
Damaged parts
Do not install parts damaged during shipment. In the case of damaged parts, contact your
Siemens representative.

The package content is described in section Scope of delivery (Page 12).

Keep the provided documentation in a safe place. The documentation is part of the HMI
device and is required for subsequent commissioning.

3.1.2 Checking the operating conditions

Note the information in the following sections of these operating instructions before
installing the HMI device:
• Certificates and approvals (Page 68)
• Electromagnetic compatibility (Page 69)
• Mechanical ambient conditions (Page 69)
• Climatic ambient conditions (Page 70)
• Protection classes (Page 72)
• Technical data (Page 76)

3.1.3 Selecting a mounting position

The device is suitable for installation in:
• Mounting cabinets
• Control cabinets
• Switchboards
• Consoles

18 Operating Instructions, 12/2023, A5E51638950-AC

 Mounting and connecting
3.1 Preparations

In the following, all of these mounting options are referred to by the general term "cabinet".
The device is self-ventilated and approved for inclined mounting at angles up to +/-35° from
the vertical in stationary cabinets.

NOTICE
Damage due to overheating
Inclined installation reduces the convection by the device and therefore the maximum
permitted ambient temperature for operation.
If there is sufficient forced ventilation, the device can also be operated in the inclined
mounting position up to the maximum permitted ambient temperature for vertical
installation. The device may otherwise be damaged, and its certifications and warranty will
be rendered null and void.
The ambient temperature ranges listed in this section apply to the temperature inside the
cabinet.

Mounting position
Select one of the approved mounting positions for your device. The approved mounting
positions are described in the following sections.

Mounting in horizontal format

Ambient temperature in the cabinet with horizontal mounting:
• Vertical mounting (0° inclined): Maximum +50 °C
• Inclined mounting (inclined up to 35°): Maximum +40 °C

Mounting in vertical format

Ambient temperature in the cabinet with vertical mounting:
• Vertical mounting (0° inclined): Maximum +40 °C
• Inclined mounting (inclined up to 35°): Maximum +35 °C

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 19
Mounting and connecting
3.1 Preparations

See also
Operating Conditions (Page 71)

3.1.4 Checking clearances

The following clearances are required around the HMI device to ensure sufficient self-
ventilation:

Required clearance around the HMI

devices.
All dimensions in mm

Smart 700 IE V4, Smart 1000 IE V4

20 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.1 Preparations

3.1.5 Making the mounting cutout

Note
Stability of the mounting cutout
The material in the area of the mounting cutout must provide sufficient strength to
guarantee the lasting and safe mounting of the HMI device.
The force of the mounting clips or operation of the device may not lead to deformation of the
material in order to achieve the degrees of protection described below.

Degrees of protection
The degrees of protection of the HMI device can only be guaranteed if the following
requirements are met:
• In order to achieve IP65 protection degree, the material thickness for the mounting cutout
should be: 2 mm to 6 mm
• Permitted deviation from plane at the mounting cutout: ≤ 0.5 mm
This condition must be met for the mounted HMI device.
• Permitted surface roughness in the area of the seal: ≤ 120 µm (Rz 120)

Mounting compatibility
The mounting cutouts of the Smart panels are compatible with the mounting cutouts of the
following SIMATIC HMI devices:

Mounting cutout Smart panel Compatible with the mounting cutouts of the HMI
device
Smart 700 IE V4 Smart 700, Smart 700 IE V2, Smart 700 IE V3
Smart 1000 IE V4 Smart 1000, Smart 1000 IE V2, Smart 1000 IE V3

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 21
Mounting and connecting
3.2 Mounting the HMI device

Dimensions of the mounting cutout

Dimensions of the mounting cutout for the Smart

panel in horizontal mounting position:

Dimensions of the mounting cutout for the Smart

panel in vertical mounting position:

All dimensions in mm

3.2 Mounting the HMI device

Required tools and accessories

Slotted screwdriver, size 2

Mounting clips Smart 700 IE V4 7

Smart 1000 IE V4 7

Smart 700 IE V4, Smart 1000 IE V4

22 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.2 Mounting the HMI device

Inserting the HMI device

Insert the HMI device into

the mounting cutout from
the front.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 23
Mounting and connecting
3.3 Connecting the HMI device

Securing the HMI device with mounting clips

1. Insert a grub screw into the mounting

clip bore hole and turn it several times.

2. Place the first mounting clip into the

corresponding cutout.

3. Fasten the mounting clip with a size 2

screwdriver. The maximum permitted
torque is 0.2 Nm.

4. Repeat steps 1 to 3 for all mounting

clips required to secure your HMI
device.

3.3 Connecting the HMI device

3.3.1 Connection sequence

Required tools and accessories

Before you start connecting the HMI device, have the following tools and accessories at hand:

Slotted screwdriver, size 2

Phillips screwdriver, size 3

Smart 700 IE V4, Smart 1000 IE V4

24 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.3 Connecting the HMI device

Crimp pliers

Power supply terminal

24 V DC with sufficient amperage.

See Technical data (Page 76)

Procedure
Keep to the following sequence of tasks when connecting the HMI device:
1. Connecting the equipotential bonding circuit (Page 25)
2. Connecting the power supply (Page 28)
3. Connecting the configuration PC (Page 29)
4. Connecting the PLC (Page 31)

Note
Strain relief
Contacts can be broken or wires can be torn off if cables are not provided adequate strain
relief.
Provide adequate strain relief for all cables.

3.3.2 Connecting the equipotential bonding circuit

Differences in electrical potential

Differences in electrical potential can develop between spatially separated system
components. Such electrical potential differences can lead to high equalizing currents on the
data cables and therefore to the destruction of their interfaces. Equalizing currents can
develop if the cable shielding is terminated at both ends and grounded to different system
parts.
Differences in potential may develop when a system is connected to different mains supplies.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 25
Mounting and connecting
3.3 Connecting the HMI device

General requirements for equipotential bonding

Differences in potential must be reduced by means of equipotential bonding conductors to
ensure trouble-free operation of the relevant components of the electronic system. The
following must therefore be observed when installing the equipotential bonding circuit:
• The effectiveness of equipotential bonding increases as the impedance of the
equipotential bonding conductor decreases or as its cross-section increases.
• If two system parts are interconnected by means of shielded data cables and their
shielding is bonded at both ends to the grounding/protective conductor, the impedance of
the additionally installed equipotential bonding conductor must not exceed 10% of the
shielding impedance.
• The cross-section of an equipotential bonding conductor must be capable of handling the
maximum equalizing current. The best practical results for equipotential bonding between
two cabinets have been achieved with a minimum conductor cross-section of 16 mm².
• Use equipotential bonding conductors made of copper or galvanized steel. Establish a
large surface contact between the equipotential bonding conductors and the
grounding/protective conductor and protect them from corrosion.
• Clamp the shielding of the data cable from the HMI device flush at the equipotential rail
using suitable cable clamps. The equipotential rail should be very close to the HMI device.
• Route the equipotential bonding conductor and data cables in parallel and with minimum
clearance between them.

Note
Equipotential bonding conductor
Cable shielding is not suitable for equipotential bonding. Always use the prescribed
equipotential bonding conductors. The cross-section of the equipotential bonding conductor
must not be less than 16 mm². Always use cables with an adequate cross-section when
installing MPI networks. The interface modules may otherwise be damaged or destroyed.

Smart 700 IE V4, Smart 1000 IE V4

26 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.3 Connecting the HMI device

Procedure

1. Interconnect the functional

earth connection of the HMI
device with an
equipotential bonding
conductor, cross-section
4 mm2.
2. Connect the equipotential
bonding conductor to the
equipotential bonding rail.
3. Strip the ends of the
Ethernet and Serial cables.
4. Connect the shield to the
equipotential bonding rail
(see figure in the circle).

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 27
Mounting and connecting
3.3 Connecting the HMI device

3.3.3 Connecting the power supply

Stripping the cable

Use power supply cables with a

maximum cross-section of 1.5 mm2.
1. Strip the ends of two power supply
cables to a length of 6 mm.
2. Attach cable sleeves to the bare
cable ends.
3. Install the end sleeves on the cable
ends using the crimp pliers.

Procedure

NOTICE
24 V DC only
An incorrectly dimensioned power supply can destroy the HMI device.
Use a 24 V DC power supply with adequate amperage; see Technical data (Page 76).

NOTICE
Safe electrical isolation
Use only 24 V DC power supply units with safe electrical isolation in accordance with IEC
60364-4-41 or HD 384.04.41 (VDE 0100, Part 410), for example, to PELV standard.
The supply voltage must be within the specified voltage range. Otherwise, malfunctions at
the HMI device cannot be ruled out.
Applies to non-isolated system configurations:
Connect the connection for GND 24 V from the 24 V power supply output to equipotential
bonding for uniform reference potential. You should always select a central point of
termination.

Smart 700 IE V4, Smart 1000 IE V4

28 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.3 Connecting the HMI device

1. Insert the two power cables into the

mains terminal and secure them
with a slotted screwdriver.

2. Connect the mains terminal to the

HMI device.

3. Switch off the power supply.

4. Insert the two remaining cable ends

into the power supply terminals
and secure them with the slotted
screwdriver.
Ensure correct polarity.

3.3.4 Connecting the configuration PC

A configuration PC gives you the following options:
• Transfer a project
• Transfer an HMI device image
• Reset the HMI device to factory settings
• Backup and restore the HMI Data

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 29
Mounting and connecting
3.3 Connecting the HMI device

Procedure

NOTICE
Data network security for communication via Ethernet
With Ethernet-based communication, the end user is responsible for the security of the data
network; proper functioning of the data network cannot be guaranteed under all
circumstances, for example, in case of targeted attacks that result in an overload of the
device.

Use a CAT5 Ethernet cable or higher to connect the configuration PC.

1. Shut down the HMI device.

2. Connect one RJ45 connector of the

LAN cable to the HMI device.

3. Connect the other RJ45 connector of

the LAN cable to the configuration PC.

Smart 700 IE V4, Smart 1000 IE V4

30 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.3 Connecting the HMI device

3.3.5 Connecting the PLC

If the HMI device contains an operating system and an executable project, connect the HMI
device to the PLC.

Note
Note the following when connecting the PLC to a panel:
• Route the data lines parallel to the equipotential bonding conductors
• Connect the shields of the data lines to the ground

NOTICE
Data network security
The end user is responsible for the security of the data network. Proper functioning of the
data network cannot be guaranteed under all circumstances, for example, in case of
targeted attacks that result in an overload of the device.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 31
Mounting and connecting
3.3 Connecting the HMI device

Connection type
Depending on the PLC type you are using, connect the PLC according to the following figures.

Ethernet connection to Serial connection to 3rd party Serial connection to SIMATIC

SIMATIC PLC device PLC

For more information, please refer to chapter "Communication with PLCs (Page 79)".

3.3.6 Connecting a USB device

Below are examples of devices designed for industrial use you can connect to the USB port of
the HMI device:
• External mouse
• External keyboard
• USB memory stick
• USB hub

Smart 700 IE V4, Smart 1000 IE V4

32 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.3 Connecting the HMI device

Note when connecting

Note
Connect a USB mouse or USB keyboard only for commissioning and servicing purposes to the
USB port.
Only use a SIMATIC USB storage medium up to a maximum of 16 GB.

Note
A maximum of 40 projects can be detected in a USB stick.
A maximum of 40 firmware files can be detected in a USB stick.

Note
USB 2.0 certified cable required
If you use a USB cable which is not USB 2.0 certified, errors may occur during data transfer.
Use only USB cables that are labeled "Certified HI-SPEED USB 2.0".

Note
USB cable length maximum 1.5 m
USB cables with lengths more than 1.5 m do not ensure secure data transfer.
The cable may not be longer than 1.5 m.

Note
Functional problem with USB port
If you connect an external device with a 230 V power supply to the USB port without using an
non-insulated installation, you may experience functional problems.
Use a non-insulated system design.

Note
Excessive rated load on port
A USB device with too high a power load may possibly cause functional problems.
Observe the values for the maximum load of the USB port. You can find the values in the
chapter "USB - X60 (Page 79)".

Note
USB memory stick is not detected.
Depending on the USB memory stick you use, it may happen that the operating system does
not detect the USB memory stick. In this case, use a different USB stick.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 33
Mounting and connecting
3.4 Switching on and testing the HMI device

3.4 Switching on and testing the HMI device

Switching on the HMI device

Switching on the power supply.

The screen lights up shortly after power
is switched on.
If the HMI device fails to start, you have
probably crossed the cables on the
power supply terminal. Check the
connected cables and change their
connection.

The Start Center opens after the operating system has started.
You operate the Start Center using the buttons on the touch screen or a connected mouse or
keyboard.

• Press the "Transfer" button to set the

HMI device to "Transfer" mode.
The "Transfer" mode can only be
activated when at least one data
channel has been enabled for the
transfer.
• Press the "Start" button to start the
project on the HMI device.
• Press the "Control Panel" button to
open the Control Panel of the HMI
device.
You can change various settings in
the Control Panel, for example, the
transfer settings.
• Press the "Recalibrate" button to
calibrate the HMI device.

Smart 700 IE V4, Smart 1000 IE V4

34 Operating Instructions, 12/2023, A5E51638950-AC
 Mounting and connecting
3.5 Securing the cables

Shutting down the HMI Device

1. Close any active projects on the HMI device.
2. Shut down the HMI device. You have the following shutdown options:
– Switch off the power supply.
– Remove the power supply terminal from the HMI device.

3.5 Securing the cables

NOTICE
Strain relief
Contacts can be broken or wires can be torn off if cables are not provided adequate strain
relief.
Provide adequate strain relief for all cables.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 35
Operating the device 4
4.1 Overview
All Smart panels are equipped with a touch screen. You use the touch screen to operate the
Control Panel or the project running on your HMI device.

CAUTION
Operation by trained professional personnel only
A project can contain certain operations that require in-depth knowledge about the specific
system on the part of the operator.
Ensure that only trained professional personnel operate the system.

Operating the touch screen

NOTICE
Damage to the touch screen
Pointed or sharp objects can damage the plastic surface of the touch screen.
Operate the touch screen only with your fingers or with a touch pen.
Triggering unintended actions
Touching several operating elements at the same time can trigger unintended actions.
Touch only one operating element on the screen at a time.

Operating elements are touch-sensitive symbols on the screen of the HMI device.
They are basically operated in the same way as mechanical keys. You activate operating
elements by touching them with your finger.

Note
The HMI device returns a visual feedback as soon as it detects that an operating element has
been touched.
The visual feedback is independent of any communication with the PLC. The visual feedback
signal therefore does not indicate whether or not the relevant action is actually executed.

Examples:
• Buttons
Buttons can have the following states:

Smart 700 IE V4, Smart 1000 IE V4

36 Operating Instructions, 12/2023, A5E51638950-AC
 Operating the device
4.2 General functions of the screen keyboard

"Untouched" "Touched"

Shadow bottom and right Shadow top and left

• Invisible buttons
The focus of invisible buttons is by default not indicated following selection. No optical
operation feedback is provided in this case.
The configuration engineer may, however, configure invisible buttons so that their outline
appears as lines when touched. This outline remains visible until you select another
operating element.
• I/O fields
A screen keyboard appears as visual feedback after you touch an I/O field, for example, to
enter a password. The type of keyboard depends on the mounting position and the
touched operating element.
The screen keyboard is automatically hidden again when input is complete.

Note
Description of all operating elements
A comprehensive description of all operating elements for your HMI device is provided in
"Display and operating elements" section of the WinCC flexible Smart online help.

4.2 General functions of the screen keyboard

The following keys are available on the screen keyboard of all Smart panels:

Cursor left

Cursor right

Delete characters left

Cancel input

Confirm input

Display infotext.
This key only appears when an infotext has been configured for the operating element.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 37
Smart 700 IE V4, Smart 1000 IE V4
4.3 The screen keyboards

4.3 The screen keyboards

A screen keyboard appears on the HMI device touch screen when you touch an operating
element that requires input. Depending on the type of operating element and the required
input, this may be an alphanumerical or a numerical keyboard.
Both keyboards are available in landscape and in portrait.

Note
Job mailbox
When job mailbox 51 "Select screen" is activated, the screen keyboard will be closed.
Key assignment
The alphanumerical screen keyboard layout is monolingual.
A language change within the project has no effect on the layout of the alphanumerical
screen keyboard.

Smart 700 IE V4, Smart 1000 IE V4

38 Operating Instructions, 12/2023, A5E51638950-AC
 Operating the device
4.4 Entering data

4.4 Entering data

Entering alphanumerical values

1. Touch the desired operating element

on the screen.
The alphanumerical screen keyboard
opens.
2. Enter the value. Depending on the
settings, the HMI device outputs an
audible signal.
Use the <Shift> key to enter lower-case
letters.
3. Press <Return> key to confirm your
entries, or cancel them with <ESC>.
Either action closes the screen
keyboard.

Entering numerical values

1. Touch the desired operating element

on the screen.
The numerical screen keyboard opens.
2. Enter the value. Depending on the
settings, the HMI device outputs an
audible signal.
3. Press <Return> key to confirm your
entries, or cancel them with <ESC>.
Either action closes the screen
keyboard.

Checking numerical value limits

Tags can be assigned limit values. Any entry of a value outside this limit is rejected. If an
alarm view is configured, a system event is triggered and the original value is displayed again.

Decimal places of numerical values

The configuration engineer can define the number of decimal places for a numerical text box.
The number of decimal places is checked when you enter a value in this type of I/O field.
• Decimal places that exceed the limit are ignored.
• Unused decimal places are padded with "0" entries.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 39
Configuring the device 5
5.1 Opening the settings

The Loader opens after the HMI device has been switched on.
Use the "Control Panel" button to open the Control Panel for parameter
assignment of the device.
You can make the following settings:
• Service and commissioning
• Ethernet parameters
• OP (Operator Panel) properties
• Sreensaver
• Password protection
• Printer
• Transfer settings
• Switch on/off the acoustic signal
• Date and time settings

Protecting the Control Panel with a password

You can protect the Control Panel against unauthorized operation with a password. If the
Control Panel is password-protected, you can open the settings in read-only mode, but you
have to enter the password to edit the settings.
This prevents inadvertent operations and increases security for the system or machine.

Note
If the Control Panel password is no longer available, you first have to update the operating
system before you can edit the settings again.
All data on the HMI device is overwritten when you update the operating system.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 40
 Configuring the device
5.2 Overview

5.2 Overview
The following table shows the functions available in the Control Panel for configuring your
HMI device.

Symbol Function
Save and load data using a USB device.
• Backup (Page 42)
• Restore (Page 43)
• OS Update (Page 44)
• Project download (Page 45)
Changing the Ethernet parameters (Page 46)

Changing display orientation and startup delay time (Page 48)

Displaying information about the HMI device (Page 49)
Calibrating the touch screen (Page 50)
Displaying licensing information for the HMI device (Page 51)
Setting the screen saver (Page 51)

Setting the device password and remote password (Page 54)

Enabling the Transfer channel (Page 52)

Enabling Network Discovery (Page 53)

Activating the acoustic signal (Page 53)

Setting the date and time (Page 54).

5.3 General functions in the Control Panel

The following keys are available on the right side of the title bar of each Control Panel dialog:

Save changes and close dialog

Discard changes and close dialog

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 41
Configuring the device
5.4 Functions for Service and Commissioning

5.4 Functions for Service and Commissioning

5.4.1 Backup

Use the "Backup" function under "Service &

Commissioning" to save device data to a USB storage
device.
1. Press "Service & Commissioning" to open the "Service &
Commissioning" dialog.
2. Select the "Backup" tab.
3. Select the data to be backed up.
– "Complete backup" generates a backup copy of the
project, recipe data and the HMI device image to a
file in PSB format.
– "Recipe backup" generates a backup copy of the
HMI device's recipe data records in PSB format.
– "User administration backup" generates a backup
copy of the HMI device's user data in PSB format.

4. Click "Next" to continue.

5. Select a USB device from the "USB Storage Devices" list.

If the list is empty, connect a USB storage device to
your Smart panel and click "Refresh".

6. Click "Next" to continue.

7. Specify a "Backup File name" or select an already

existing backup file to overwrite from the "Compatible
backup files" list.

8. Click one of the buttons at the bottom of the dialog:

– "Details" will display the following data of a
backup file you have selected in the list:
- The device compatible with the backup file
- The backup path on the USB storage device
- The backup file name
- The backup file size
– "Next" will continue and save the data. If you click
"Next", navigate to Step 9.
– "Delete" will remove a selected backup file after
confirmation.
– "Cancel" will abort the backup operation.
9. Confirm the settings and click "Start". Then the backup
operation starts.

Smart 700 IE V4, Smart 1000 IE V4

42 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.4 Functions for Service and Commissioning

5.4.2 Restore

Use the "Restore" function under "Service &

Commissioning" to load a backup file from a USB
storage device. The data which is loaded depends
on the contents of the backup file. For details, refer
to chapter "Backup (Page 42)".
1. Press "Service & Commissioning" to open the
"Service & Commissioning" dialog.

2. Select the "Restore" tab.

3. Click "Next" to continue.

4. Select a USB device from the "USB Storage

Devices" list. If the list is empty, connect a USB
storage device to your Smart panel and click
"Refresh".

5. Click "Next" to continue.

6. Select a backup file to load from the "Compatible

backup files" list.

7. Click one of the buttons at the bottom of the

dialog:
– "Details" will display the following data of a
backup file you have selected in the list:
- The device compatible with the backup file
- The backup path on the USB storage device
- The backup file name
- The backup file size
– "Next" will continue and load the data. If you
click "Next", navigate to Step 8.
– "Delete" will remove a selected backup file
after confirmation.
– "Cancel" will abort the restore operation.
8. Confirm the settings and click "Start". Then the
restore operation starts.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 43
Configuring the device
5.4 Functions for Service and Commissioning

5.4.3 OS update

Use the "OS Update" function under "Service &

Commissioning" to update the operating system.
1. Press "Service & Commissioning" to open the "Service &
Commissioning" dialog.
2. Select the "OS Update" tab.
3. Click "Next" to continue.

4. Select a USB device from the "USB Storage Devices" list. If

the list is empty, connect a USB storage device to your
Smart panel and click "Refresh".

5. Click "Next" to continue.

6. Select an already existing OS file to overwrite from the

"Compatible OS files" list.

7. Click one of the buttons at the bottom of the dialog:

– "Details" will display the following data of an OS file
you have selected in the list:
- The device compatible with the OS file
- The OS update file path on the USB storage device
- The OS file name
- The OS version
- The OS file size
– "Next" will continue to update the operating system. If
you click "Next", navigate to Step 8.
– "Delete" will remove a selected OS file after
confirmation.
– "Cancel" will abort the OS update operation.
8. Confirm the settings and click "Start". Then the OS update
operation starts.
Note: After the operating system is updated, the control
panel will restart automatically.

Smart 700 IE V4, Smart 1000 IE V4

44 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.4 Functions for Service and Commissioning

5.4.4 Project

Use the "Project" function under "Service & Commissioning"

to download a project from a USB storage device.
1. Press "Service & Commissioning" to open the "Service &
Commissioning" dialog.
2. Select the "Project" tab.
3. Click "Next" to continue.

4. Select a USB device from the "USB Storage Devices" list. If

the list is empty, connect a USB storage device to your
Smart panel and click "Refresh".

5. Click "Next" to continue.

6. Select an already existing project file to overwrite from the

"Compatible Project files" list.

7. Click "Next" to continue.

8. Select the following checkbox as you need:
– Overwrite User Administration Data: overwrites the
HMI device's user administration data.
– Overwrite Recipe Data: overwrites the HMI device's
recipe data records.
– Upgrade Firmware: updates the HMI device's
firmware.
9. Click "Next" to continue.
10.Confirm the settings and click "Start". Then the project
download starts.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 45
Configuring the device
5.5 Changing the Ethernet parameters

5.5 Changing the Ethernet parameters

Note
Communication errors caused by IP address conflicts
Communication errors can occur if several devices in a network share the same IP address.
Assign a unique IP address to every HMI device in the network.

Note
The default IP address is 192.168.2.10.

Smart 700 IE V4, Smart 1000 IE V4

46 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.5 Changing the Ethernet parameters

1. Press "Ethernet" to open the "Ethernet

Settings" dialog.
2. Choose either automatic address
assignment via "DHCP", or user-specific
address assignment.
3. If assigning a user-specific address, use
the screen keyboard to enter valid
values in the "IP address", "Subnet
mask" text boxes and if applicable in
the "Default gateway" text box.
4. Switch to the "Mode" tab sheet.
5. Specify the transmission rate in the
"Speed" input field.
Valid values are 10 Mbps or 100 Mbps.
6. Select "Half duplex" or "Full duplex" in
the Communication Link section.
7. If the "Auto Negotiation" entry is
selected, the transmission type and
transmission rate in the network will be
automatically detected and set.
8. Switch to the "Device" tab sheet.
9. Enter a network name for your HMI
device in the "Device name" field.
The name must meet the following
conditions:
The name may contain characters "a"
to "z", numbers "0" to "9"; special
characters: "-" and "."

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 47
Configuring the device
5.6 Changing display orientation and startup delay time

5.6 Changing display orientation and startup delay time

Note
Orientation of the screen (portrait or landscape)
The screen orientation is defined by the configuration engineer in the course of project
creation. The appropriate screen orientation is set automatically when you transfer the
project to the HMI device.
Do not make any changes to the screen orientation if a project exists on the HMI device with
a different orientation. The screen content may otherwise be truncated.

1. Press "OP" to open the "OP

Properties" dialog.

2. Select the screen orientation:

– "0° (Landscape)" for landscape
– "90° (Portrait)" for portrait

3. Set the "Delay time" in the "Startup

delay" section. The delay time in
seconds defines the waiting time
between the appearance of the
loader and the start of the project.
Valid range of values:
0 to 60 seconds.

Smart 700 IE V4, Smart 1000 IE V4

48 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.7 Displaying information about the HMI device

5.7 Displaying information about the HMI device

1. Press "OP" to open the "OP

Properties" dialog.

2. Switch to the "Device" tab.

The "Device" tab is used to display

specific information on the HMI
device. You will need this
information when contacting
Technical Support.
– "Device:" HMI device name
– "Flashsize": Size of flash
memory
– "Bootloader": Boot loader
version
– "Bootl. Re. Date": Release date
of the boot loader
– "Image": Image version of the
device image.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 49
Configuring the device
5.8 Calibrating the touch screen

5.8 Calibrating the touch screen

1. Click the "Recalibrate" button.

2. Touch the cross in the screen

center.

3. Touch the floating cross in the

corners of the screen one after the
other.
If you have not touched a
calibration cross within the
expected range, calibration will
start once again.
If you have touched all calibration
crosses within the expected range,
calibration is complete.

Smart 700 IE V4, Smart 1000 IE V4

50 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.9 Displaying licensing information for the HMI device

5.9 Displaying licensing information for the HMI device

1. Press "OP" to open the "OP

Properties" dialog.

2. Switch to the "License" tab.

The "License" tab is used to display
the licensing information for the
software of the HMI device.

5.10 Setting the screen saver

Note
Burn-in effect
The screen contents may leave a faint version (ghost) of the image in the background if they
appear for too long.
The "ghost" will disappear automatically after some time. The longer the same content is
displayed on the screen, the longer it will take for the burn-in effect to disappear.
The screen saver helps to prevent burn-in.
Always use the screen saver.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 51
Configuring the device
5.11 Enabling the Transfer channel

1. Press "Screensaver" to open the

"Screensaver Settings" dialog.

2. Enter the number of minutes

before the screen saver is to be
activated under "Wait time".
Touch the text box to do this. You
can enter values from 5 to 360
minutes. Entering "0" disables the
screen saver.

5.11 Enabling the Transfer channel

You must enable one data channel to transfer a project to the HMI device.

Note
After having completed the project transfer, you can protect the HMI device against
unintentional overwriting of project data and of the HMI device image by locking all data
channels.

1. Press "Transfer" to open the "Transfer

Settings" dialog.

2. Switch on "Enable transfer".

3. To enable automatic transfer, switch on

"Remote Control".
When the automatic transfer is
activated, you can start a transfer from
the configuration PC while the project
is running. The running project is
closed in this case and the new project
is transferred.
The new project starts after it has been
transferred.

Use "Advanced" button to check the

Ethernet settings, if required.
Changing the Ethernet parameters (Page 46)

Smart 700 IE V4, Smart 1000 IE V4

52 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.12 Enabling the Network Discovery

5.12 Enabling the Network Discovery

Enabling network discovery means that the HMI device can be found after being searched in
the Online setting page of Wincc Flexible SMART. For detailed information, refer to the
document WinCC flexible SMART Online Help.
Enable the network discovery as follows:

1. Press "Transfer" to open the "Transfer

Settings" dialog.

2. Select the checkbox "Network

Discovery".

5.13 Activating the acoustic signal

1. Press "Sound Settings" to open the

"Sound Settings" dialog.

2. Set the "Sound" to "ON".

Once you have set the "Sound" to

"ON", you receive an acoustic
feedback each time you touch the
touch screen.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 53
Configuring the device
5.14 Setting the date and time

5.14 Setting the date and time

1. Press "Date&Time" to open the

"Date&Time Properties" dialog.
2. Click the plus icon or the minus icon in
"Time shift" field.
3. Click the "Apply" button.

5.15 Changing the password settings

You can set device password and remote password in Password Properties dialog.
Device password protection prevents unauthorized access to the control panel.
Remote password provides secure authentication for remote access to the HMI device.

Note
It is recommended that you set a secure device password and a secure remote password.
A secure password
• is at least eight characters in length.
• contains upper and lower case letters, numbers and special characters except for * ? .
% / \ ' ".
• cannot contain spaces.
• cannot be a word listed in a dictionary.
• cannot be a name or identifier that can be derived from personal information.
• cannot consist of a string of adjacent characters on the keyboard (for example, 123456 or
asdfg).
• cannot contain the same character repeated several times (for example, AAAA).

Smart 700 IE V4, Smart 1000 IE V4

54 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.15 Changing the password settings

5.15.1 Setting the device password

Note
If the device password is no longer available for the control panel, you first have to update
the operating system before you can make any changes in the control panel. All data on the
HMI device will be overwritten when you update the operating system.

Note
If you enter wrong device password for three times consecutively, password verification is
unavailable for 30 seconds. 30 seconds later, if you enter wrong device password for one
time, the duration that password verification is unavailable increases to 60 seconds and the
duration increases by 30 seconds every time you enter wrong device password, and the
maximum of duration is one hour.

Activating device password protection

1. Press "Password" to open the

"Password Properties" dialog.
"Device Password" and "Remote
Password" tab are displayed.

2. In the "Device password" tab, touch

the "Password" text box and enter a
password in the alphanumerical
screen keyboard.

After entering the device

password, the password strength is
displayed.
3. Confirm the password in the
"Confirm Password" text box.
4. Press the "Apply" button.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 55
Configuring the device
5.15 Changing the password settings

Deactivating device password protection

1. Press "Password" to open the

"Password Properties" dialog.

2. In the "Device password" tab, delete

the entries in the "Password" text
box.

3. Delete the entries in the

"Confirm Password" text box.
4. Press the "Apply" button.

5.15.2 Setting the remote password

Note
Remote password rule
• The remote password cannot contain the following characters: `~^{}
• The remote password length cannot exceeds 16 characters.

Smart 700 IE V4, Smart 1000 IE V4

56 Operating Instructions, 12/2023, A5E51638950-AC
 Configuring the device
5.15 Changing the password settings

Activating remote password protection

1. Press "Password" to open the

"Password Properties" dialog.
"Device Password" and "Remote
Password" tab are displayed.

2. In the "Remote password" tab,

select the checkbox "Enable".
3. Touch the "Password" text box and
enter a password in the
alphanumerical screen keyboard.

After entering the remote

password, the password strength is
displayed.
4. Confirm the remote password in
the "Confirm Password" text box.
5. Press the "Apply" button.

Deactivating remote password protection

1. Press "Password" to open the

"Password Properties" dialog.

2. In the "Remote password" tab,

unselect the checkbox "Enable".
Then the entries in the "Password"
text box and the
"Confirm Password" text box will be
automatically deleted.
3. Press the "Apply" button.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 57
Commissioning a project 6
6.1 Overview

Configuration phase
A project – the process image of the working process – is created during configuration via a
configuration PC to visualize automated working processes. The process displays for the
project contain displays for values and messages which provide information about process
statuses. The process control phase follows the configuration phase.

Process control phase

The project must be transferred to the HMI device if it is to be used in process control.
Another prerequisite for process control is that the HMI device is connected online to a PLC.
Current working processes - operating and observing - can then be subject to process control.

Transferring the project to the HMI device

You can transfer a project to an HMI device as follows:
• Transfer from the configuration PC
• Pack & Go:
A project is transferred to the HMI device using a PC without WinCC flexible SMART. The
configuration software does not need to be installed on the PC.
• Restore from USB:
Load a complete backup file (see section "Restore (Page 43)").

Commissioning and recommissioning

Initial startup and recommissioning differ in the following respects:
• With initial startup, there is not project on the HMI device.
The HMI device is also in this state after the operating system has been updated.
• When recommissioning, any project already on the HMI device is replaced.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 58
 Commissioning a project
6.2 Operating modes

6.2 Operating modes

Operating modes
The HMI device may be in the following operating modes:
• Offline
• Online
• Transfer
"Offline mode" and "Online mode" can be set on both the configuration PC and the HMI
device. To set these modes on the HMI device, use a corresponding operating element of the
project.

Changing the operating mode

The configuration engineer must have configured an appropriate operating element to allow
a change of the operating mode on the HMI device during ongoing operation.
Additional information may be available in your system documentation.

"Offline" operating mode

In this mode, there is no communication between the HMI device and the PLC. Even though
the HMI device can be operated, it cannot exchange data with the PLC.

"Online" operating mode

In this mode, the HMI device and the PLC communicate with each other. You can operate the
project on the HMI device.

"Transfer" mode
In this mode, you can transfer a project from the configuration PC to the HMI device, backup
and restore HMI device data or update firmware.
The following options are available for setting "Transfer" mode on the HMI device:
• When the HMI device starts up:
Start "Transfer" mode manually in the HMI device Loader.
• During ongoing operation:
Start the "Transfer" mode manually within the project using an operating element. The
HMI device toggles to "Transfer" mode when automatic mode is set and a transfer is
initiated on the configuration PC.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 59
Commissioning a project
6.3 Data transmission options

6.3 Data transmission options

Overview
The following table shows the options for data transfer between the HMI device and the
configuration PC.

Data transmission type USB stick Serial Ethernet

Backup/restore of an image file ✓ - ✓
containing the following HMI device
data:
• Project data
• Recipe data
• User administration data
Operating system update ✓ - ✓
Operating system update with "Reset to - - ✓
factory settings"
Project transfer ✓ - ✓

6.4 Transfer

6.4.1 Overview
Transfer the executable project from the configuration PC to the HMI device.
Use the following methods to transfer a project:
• Start the transfer manually
• Starting the transfer automatically
• A USB storage device, refer to chapter "Functions for Service and Commissioning
(Page 45)"
• HMI device maintenance menu in Wincc flexible Smart.
For detailed information, refer to the document WinCC flexible SMART Information System
System Manual.
You can start the "Transfer" mode manually or automatically on the HMI device.
Transferred data is written directly to internal flash memory of the HMI device. Assign
parameters of a corresponding data channel before you start the transfer.

Note
Unauthorized users are not allowed to access and download the WinCC flexible SMART
project.

Smart 700 IE V4, Smart 1000 IE V4

60 Operating Instructions, 12/2023, A5E51638950-AC
 Commissioning a project
6.4 Transfer

6.4.2 Starting the manual transfer

Introduction
You can manually switch the HMI device to "Transfer" mode as follows:
• At runtime, using a configured operating element.
• In the Loader of the HMI device.

Requirements
• The project is open in WinCC flexible Smart.
• The project is compiled.
• The HMI device is connected to a configuration PC via Ethernet.
• The Ethernet parameters are assigned on the HMI device.
• The HMI device is in "Transfer" mode.

Procedure
1. On the configuration PC, select the "Transfer settings" command from the "Project >
Transfer" menu in WinCC flexible Smart.
The "Select devices for transfer" dialog opens.
2. Select the HMI device in the left area of the dialog.
3. Select the type of interconnection for the HMI device and the configuration PC.
Set the connection parameters.
4. Set the transfer parameters in the right area of the dialog.
5. Start the transfer in WinCC flexible Smart by selecting "Transfer".
The configuration PC checks the connection to the HMI device. The project is transferred to
the HMI device. An error message is displayed on the configuration PC if the connection is
not available or disrupted.

Result
The project is available on the HMI device following successful transfer. The transferred
project starts automatically.

6.4.3 Starting the transfer automatically

Introduction
If automatic transfer is activated, the HMI device automatically changes to "Transfer" mode at
runtime as soon as a transfer is started on the connected configuration PC.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 61
Commissioning a project
6.4 Transfer

Automatic transfer is particularly suited for the test phase of a new project because transfer is
completed without interfering with the HMI device.

Note
If automatic transfer is activated on the HMI device and a transfer is initiated on the
configuration PC, the project currently running is automatically stopped. The HMI device then
automatically switches to "Transfer" mode.
After the commissioning phase, deactivate the automatic transfer so that the HMI device
cannot be inadvertently switched to transfer mode. Transfer mode can trigger unintentional
actions in the system.
You can issue a password in the Control Panel to restrict access to the transfer settings and
thus avoid unauthorized modifications.

Requirements
• The project is open in WinCC flexible Smart.
• The project is compiled.
• The HMI device is connected to a configuration PC via Ethernet.
• The Ethernet parameters are assigned on the HMI device.
• The automatic transfer is enabled in the Start Center.

Procedure
1. On the configuration PC, select the "Transfer settings" command from the "Project >
Transfer" menu in WinCC flexible Smart.
The "Select devices for transfer" dialog opens.
2. Select the HMI device in the left area of the dialog.
3. Select the type of interconnection for the HMI device and the configuration PC.
Set the connection parameters.
4. Set the transfer parameters in the right area of the dialog.
5. Start the transfer in WinCC flexible Smart by selecting "Transfer".

Result
The configuration PC checks the connection to the HMI device. The HMI device shuts down
the current project and automatically changes to "Transfer" mode. The project is transferred
to the HMI device. An error message is displayed on the configuration PC if the connection is
not available or disrupted.
The project is available on the HMI device following successful transfer. The transferred
project starts automatically.

Smart 700 IE V4, Smart 1000 IE V4

62 Operating Instructions, 12/2023, A5E51638950-AC
 Commissioning a project
6.4 Transfer

6.4.4 Testing a project

Introduction
You have the following options to test a project:
• Test the project on the configuration PC:
You can test a project on a configuration PC, using a simulator. You can find more detailed
information on this in the WinCC flexible Smart online help.
• Offline testing of the project on the HMI device:
Offline testing means that communication between the HMI device and PLC is down while
the test is being carried out.
• Online testing of the project on the HMI device:
Online testing means that the HMI device and the PLC communicate with each other
during testing.
Perform the tests, starting with the "Offline test", followed by the "Online test".

Note
You should always test the project on the HMI device on which the project will be used.

Check the following:

1. Check the correct layout of the screens.
2. Check the screen navigation.
3. Check the input objects.
4. Enter the tag values.
The test ensures that the project will run as you intended on the HMI device.

Offline testing

Requirement
• The project has been transferred to the HMI device.
• The HMI device is in "Offline" mode.

Procedure
In "Offline" mode, you can test individual project functions on the HMI device without them
being affected by the PLC. PLC tags, therefore, are not updated.
Test the operating elements and visualization of the project as far as possible without
connecting to the PLC.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 63
Commissioning a project
6.5 Backup and restore

Online testing

Requirement
• The project has been transferred to the HMI device.
• The HMI device is in "Online" mode.

Procedure
In "Online" mode, you can test individual project functions on the HMI device without them
being affected by the PLC. PLC tags are updated in this case.
You have the option to test all communication-dependent functions, for example alarms, etc.
Test the operating elements and views of the project.

6.5 Backup and restore

Overview
You can back up and restore the following data in the internal flash memory of the HMI
device with a PC or an USB storage device:
• Project and HMI device image
• Password list
• Recipe data
Use one of the following tools for backup and restore:
• A USB storage device, refer to chapter "Functions for Service and Commissioning
(Page 42)"
• HMI device maintenance menu in Wincc flexible Smart. For detailed information, refer to
the document WinCC flexible SMART Information System System Manual.

General information

Note
Power failure
If a complete restore operation is interrupted due to power failure on the HMI device, the
previous operating system will be started.
Compatibility conflict
If a message is output on the HMI device warning you of a compatibility conflict during the
restore operation, the operating system must be updated.

Smart 700 IE V4, Smart 1000 IE V4

64 Operating Instructions, 12/2023, A5E51638950-AC
 Commissioning a project
6.6 Updating the operating system

Note
A data transfer can take several minutes, depending on data volume and transmission rate.
Observe the status display. Do not interrupt the data transfer.

6.6 Updating the operating system

A compatibility conflict may occur when transferring a project to the HMI device. This is
caused by different versions of the configuration software used and the HMI device image
available on the HMI device. If there are different versions, the transfer is aborted. A message
indicating a compatibility conflict is displayed on the configuration PC.
There are two ways to match the versions:
• Update the HMI device image if the project was created with the most recent version of
the configuration software.
• Transfer a matching version of the HMI device image if you do not want to adapt the
project for the HMI device to the most recent version of the configuration software for the
project.

Note
Data loss
All data on the HMI device, such as the project and licenses, will be deleted when you
update the operating system.

Note
Calibrating the touch screen
After the update, you may have to recalibrate the touch screen.

Use one of the following tools to update the operating system:

• A USB storage device, refer to chapter "Functions for Service and Commissioning
(Page 44)".
• HMI device maintenance menu in Wincc flexible Smart.
For detailed information, refer to the document WinCC flexible SMART Information System
System Manual.
In Wincc flexible SMART, you can update the operating system with or without resetting to
factory settings.

Note
Ethernet parameters {"Safety instruction";"Data channel"}
When resetting to factory settings, all Ethernet parameters are reset. A transfer can only
be started after a reconfiguration of the Ethernet parameters.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 65
Maintenance and care 7
7.1 Maintenance and care

Introduction
The HMI device is designed for maintenance-free operation. However, make sure you keep
the touch screen clean.
Requirement
Use a cleaning cloth dampened with a cleaning agent to clean the equipment. Only use water
with a little liquid soap or a screen cleaning foam.

Note
Unintentional response
When cleaning the touch screen, an unintentional response in the PLC can be triggered by
touching screen objects.
Switch the HMI device off or, if available, activate the clean screen function before cleaning
to prevent unintentional responses.

Note
Damage caused by unauthorized cleaning products
The HMI device may be damaged if compressed air, steam jet blowers, aggressive solvents or
scouring powders are used for cleaning purposes.
Do not clean the HMI device with compressed air or steam jet blowers. Do not use aggressive
solvents or scouring powder.

Procedure
Proceed as follows:
1. Shut down the HMI device.
2. Spray the cleaning solution onto a cleaning cloth. Do not spray directly onto the HMI device.
3. Clean the HMI device. When cleaning the display wipe from the screen edge inwards.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 66
 Maintenance and care
7.2 Recycling

7.2 Recycling

Recycling and disposal

The HMI devices described in these operating instructions can be recycled due to the low
levels of pollutants. Contact a certified disposal service company for environmentally sound
recycling and disposal of your old devices.
Dispose the HMI devices in accordance with local regulations.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 67
Technical specifications 8
8.1 Certificates and approvals

Note
The HMI device itself is approved as shown on the rear panel labels.

CE approval
The HMI device meets the general and safety-related requirements of the following EU
directives and conforms to the harmonized European standards (EN) published in the official
gazettes of the European Union:
• 2014/30/EU "Electromagnetic Compatibility" (EMC Directive)

RoHS directive
This product meets the requirements stated in the RoHS directive (Restriction of Hazardous
Materials): 2011/65/EU
Compliance with the directive has been reviewed according to the following standard: EN IEC
63000

UKCA
The HMI device complies with the designated British standards (BS) published in the official
consolidated list of the British Government. The HMI device meets the requirements and
protection targets of the following regulations and related amendments:
• Electromagnetic Compatibility Regulations 2016 (EMC)
• Regulations on the restriction of the use of certain hazardous substances in electrical and
electronic equipment 2012 (RoHS).
UK Declarations of Conformity for the respective authorities are available from:
Siemens AG
Digital Industries
Factory Automation
DI FA TI COS TT
P.O. Box 1963
D-92209 Amberg
The UK Declaration of Conformity is also available for download from the Siemens Industry
Online Support website under the keyword "Declaration of Conformity".

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 68
 Technical specifications
8.2 Electromagnetic compatibility

WEEE label (European Union)

Disposal instructions, observe the local regulations and the section "Recycling" (Page 67).

8.2 Electromagnetic compatibility

The device is designed for industrial use.

8.2.1 Emitted interference

The device meets the requirements according to EN/IEC 61000-6-4. The device corresponds
to limit class A defined in CISPR 11 or EN 55011.

Note
The HMI device is not intended for use in residential areas. Operation of an HMI device in
residential areas can have a negative influence on radio/TV reception.

8.2.2 Immunity to interferences

The device meets the requirements according to EN/IEC 61000-6-2.

8.3 Mechanical ambient conditions

8.3.1 Transport and storage conditions

The following information is for a device that is transported and stored in its original
packaging.
The device meets the requirements according to EN/IEC 61131-2 with the following
amendments and limitations:

Type of condition Permitted range

Free fall ≤ 0,3 m
Vibration to IEC 60068-2-6 5 to 8.4 Hz, deflection 3.5 mm
8.4 to 500 Hz, acceleration 1 g
Shock to IEC 60068-2-27 250 m/s2, 6 ms, 1000 shocks per axis

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 69
Technical specifications
8.4 Climatic ambient conditions

8.3.2 Operating Conditions

The following information applies to a device installed according to the specifications in these
operating instructions.
The HMI device is designed for stationary operation in a location protected from the effects of
the weather.
The device meets the requirements according to EN/IEC 61131-2 with the following
amendments and limitations:

Type of condition Permitted range

Vibration to IEC 60068-2-6 5 to 8.4 Hz, deflection 3.5 mm
8.4 to 200 Hz, acceleration 1 g
Shock to IEC 60068-2-27 150 m/s2, 11 ms, 3 shocks per axis

8.4 Climatic ambient conditions

8.4.1 Transport and storage conditions

The following information is for a device that is transported and stored in its original
packaging.
The device meets the requirements according to EN/IEC 61131-2 with the following
amendments and limitations:

Type of condition Permitted range

Temperature –20 °C to +60 °C
Atmospheric pressure 1140 to 660 hPa, corresponds to an elevation of -1000 m to 3500 m
Relative humidity 10% to 90%, without condensation
Pollutant concentration SO2: < 0.5 ppm; Relative humidity < 60%, no condensation
H2S: < 0.1 ppm; Relative humidity < 60%, no condensation

Note
Ensure that no condensation (dewing) develops on or inside the HMI device after
transporting it at low temperatures or after it has been exposed to extreme temperature
fluctuations.
The HMI device must have acquired room temperature before it is put into operation. Do not
expose the HMI device to direct radiation from a heater in order to warm it up. If dewing has
developed, wait approximately 4 hours until the HMI device has dried completely before
switching it on.

Smart 700 IE V4, Smart 1000 IE V4

70 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.4 Climatic ambient conditions

8.4.2 Operating Conditions

The following information applies to a device installed according to the specifications in these
operating instructions.
The HMI device is designed for stationary operation in a location protected from the effects of
the weather.
The device meets the requirements according to EN/IEC 61131-2 with the following
amendments and limitations:

Type of condition Permitted range

Temperature, device in Vertical installation 0 °C to 50 °C
landscape format Inclined installation up to 35° 0 °C to 40 °C
Temperature, device in Vertical installation 0 °C to 40 °C
portrait format Inclined installation up to 35° 0 °C to 35 °C
Atmospheric pressure 1140 to 795 hPa, corresponds to an elevation of -1000 m to 2000 m
Relative humidity 10% to 90%, without condensation
Pollutant concentration SO2: < 0.5 ppm; Relative humidity < 60%, no condensation
H2S: < 0.1 ppm; Relative humidity < 60%, no condensation

8.4.3 Climate diagram

The diagram below shows the extended range for temperature and humidity during
operation based on EN/IEC 61131-2.
The information applies to a device installed in landscape without inclination.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 71
Technical specifications
8.5 Protection classes

8.5 Protection classes

8.5.1 Insulation test

The device meets the requirements according to EN/IEC 61010-2-201.

Circuits with a nominal voltage of Ue to other circuits or ground Test voltage

< 50 V 707V DC

8.5.2 Protection against foreign objects and water

The device meets the requirements according to EN 60529.

Device side Degree of protection

Front IP65, when mounted
Rear IP20, Touch protection test with standard test probes. There is no protection against
ingress by water.

The degree of protection of the device front can only be guaranteed if the mounting seal lies
flush against the mounting cutout. Read the corresponding information in chapter "Making
the mounting cutout (Page 21)".

Smart 700 IE V4, Smart 1000 IE V4

72 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.6 Dimension drawings

8.6 Dimension drawings

8.6.1 Dimension drawing of Smart 700 IE V4

All dimensions in millimeters

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 73
Technical specifications
8.6 Dimension drawings

8.6.2 Dimension drawing of Smart 1000 IE V4

All dimensions in millimeters

Smart 700 IE V4, Smart 1000 IE V4

74 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.7 Rating plate

8.7 Rating plate

The rating plate includes information that clearly identifies your device. You need this
information when you contact Customer Support.
The following figure shows the rating plate on the device SMART 1000 IE V4 as an example.

ID link
The ID link is a globally unique identifier according to IEC 61406, which you can find as a QR
code on the product label and product package label. After scanning the QR code on the
product label or on the packaging label with a smartphone camera, barcode scanner or
reader app, the ID link takes you to the digital nameplate of your products, where you can
look through the following information:
• Manuals: Quick Install Guide, Operating Instructions and Original Instructions
• Certificates
• Technical data
• FAQ information

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 75
Technical specifications
8.8 Technical data

8.8 Technical data

Weight

Smart 700 IE V4 Smart 1000 IE V4

Weight without packaging Approx. 770 g Approx. 1200 g

Display

Smart 700 IE V4 Smart 1000 IE V4

Type LCD TFT
Active display area 154.1 x 85.9 mm (7") 222.7 x 125.3 mm (10.1")
Resolution 800 x 480 pixels 1024 x 600 pixels
Possible colors 24-bit (16M colors)
Brightness control -
Backlighting LED LED
Half Brightness Life Time (MTBF 1) 20,000 h 15,000 h
Pixel error class in accordance with EN II
ISO 9241-307
1 MTBF: Operating hours after which the maximum brightness is reduced by half compared to the original value. MTBF is
increased by using the integrated dimming function, for example, time-controlled via screen saver or centrally via
PROFIenergy.

Input device

Smart 700 IE V4 Smart 1000 IE V4

Type Touch screen, analog resistive

Memory

Smart 700 IE V4 Smart 1000 IE V4

Data memory 256 MBytes
Program memory 256 MBytes

Interfaces

Smart 700 IE V4 Smart 1000 IE V4

1 x RS 422/485 max. 187.5 Kbits/s
1 x Industrial Ethernet RJ45 10/100 Mbits/s, with auto-crossover
1 x USB 2.0 max. 500 mA

Smart 700 IE V4, Smart 1000 IE V4

76 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.9 Ports description

Supply voltage

Smart 700 IE V4 Smart 1000 IE V4

Rated voltage +24 V DC
Permitted voltage range 19.2 to 28.8 V (–20%, +20%)
Maximum permitted transients 35 V (500 ms)
Minimum time between two transients 50 s
Power consumption 1 4.8 W 5.3 W
Current typical Approx. 200 mA Approx. 230 mA
consumption Maximum constant Approx. 380 mA Approx. 400 mA
current
Inrush current I2t Approx. 0.1 A2s
Fuse, internal Electronic
1 The power loss generally corresponds to the specified value for power consumption.

Miscellaneous

Smart 700 IE V4 Smart 1000 IE V4

Buffered real-time clock 1, can be Yes
synchronized
Acoustic feedback Yes
1 Typical buffer time: 6 weeks

8.9 Ports description

8.9.1 DC24V - X80

2-pin socket

Pin number Assignment

1 +24 V DC (L+)
2 GND 24 V (M)
3 FE

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 77
Technical specifications
8.9 Ports description

8.9.2 PPI / RS422 / RS485 - X2

Sub-D socket, 9-pin, with screw lock

Pin Assignment for the RS 422 Assignment for the RS 485

1 not connected not connected
2 not connected not connected
3 TxD+ Data channel B (+)
4 RxD+ RTS
5 GND 5 V, floating GND 5 V, floating
6 +5 V DC, floating +5 V DC, floating
7 not connected not connected
8 TxD– Data channel A (–)
9 RxD– NC

8.9.3 Ethernet (LAN) - X1

RJ45 socket

Pin Assignment
1 Tx+
2 Tx–
3 Rx+
4 n. c.
5 n. c.
6 Rx–
7 n. c.
8 n. c.

Smart 700 IE V4, Smart 1000 IE V4

78 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.10 Communication with PLCs

8.9.4 USB - X60

USB socket

The following table shows the pin assignment of the USB port.

Pin Assignment
1 +5 V DC, out, max. 500 mA
2 USB-DN
3 USB-DP
4 GND

8.10 Communication with PLCs

Compatible PLCs
The following PLC types can be used with the Smart V4 panels.

PLC type Supported protocols

SIEMENS S7-200 Ethernet, PPI, MPI
SIEMENS S7-200 CN Ethernet, PPI, MPI
SIEMENS S7-200 Smart Ethernet, PPI, MPI
SIEMENS LOGO! Ethernet
Mitsubishi FX * Serial point-to-point
Mitsubishi Protocol 4 * Serial Multi Point
Modicon Modbus PLCs * Serial point-to-point
Omron CP, CJ * Serial Multi Point

* Typical PLCs of this PLC type have been successfully tested and approved.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 79
Technical specifications
8.10 Communication with PLCs

Note
Security: Protecting networks against physical access and possible reads and writes of
HMI data
Communication through Modbus RTU, S7 Ethernet, MPI/PPI protocols have no security
features. If an attacker can physically access your networks through one of these forms of
communication, the attacker can possibly read and write HMI data. Unauthorized access to
HMI data can result in defect production and plant stillstand.
You must protect these forms of communication by limiting physical access. For security
information and recommendations, refer to Operational Guidelines for Industrial Security
(https://new.siemens.com/global/en/products/automation/topic-areas/industrial-
security.html).

PLC connector schematics

The following adaption is required when connecting a PLC to a Smart Panel through Isolated
Serial Port.

S7-200 connector

Smart 700 IE V4, Smart 1000 IE V4

80 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.10 Communication with PLCs

Mitsubishi FX connector

Mitsubishi Protocol 4 connector

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 81
Technical specifications
8.11 Scope of functions with WinCC flexible SMART

Schneider Modicon connector

Omron connector

8.11 Scope of functions with WinCC flexible SMART

The following tables show the objects that can be integrated in a project for a Smart panel.
The following tables support you in estimating whether your project is still within the
performance features of the HMI device.
The specified maximum values are not additive. We cannot guarantee proper functioning of
configurations on devices in which all system limits are exploited.
In addition to the limitations specified, allowances must also be made for restrictions in
configuration memory resources.

Smart 700 IE V4, Smart 1000 IE V4

82 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.11 Scope of functions with WinCC flexible SMART

Tags, values and lists

Object Specification Quantity

Tags Quantity 800
Limit value monitoring Input/output Yes
Linear scaling Input/output Yes
Elements per array Quantity 100
Text lists Quantity 200
Graphics lists Quantity 100

Alarms

Object Specification Quantity

Alarms Number of alarm classes 32
Number of discrete alarms 400
Number of analog alarms 20
Length of the alarm text 80 characters
Number of tags in an alarm Max. 8
Display Alarm window, alarm view
Acknowledge error alarm individually Yes
Acknowledge multiple error alarms simultaneously (group 16 acknowledgment
acknowledgement) groups
Edit alarm Yes
Alarm indicator Yes
Alarm buffer Alarm buffer capacity 512 alarms
Simultaneously queued alarm events Max. 64
View alarm Yes
Delete alarm buffer Yes

Screens

Object Specification Quantity

Screens Quantity 150
Fields per screen 100
Tags per screen 100
Template Yes
Objects per screen Flow block 32
Recipe view 10
Trend view 8
Table view 8
Diagnostic view 1
User view 1
Alarm view 20
Multiple tags (array elements) 1 100
1 This includes array elements included in recipes.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 83
Technical specifications
8.11 Scope of functions with WinCC flexible SMART

Recipes
The specified values are maximum values and should not be used additive.

Object Specification Quantity

Recipes Quantity 50
Elements per recipe1 100
Data records per recipe 100
User data length in KB per data record 32
Reserved memory for data records in the internal Flash 2560 KB
1 Each element used in arrays represents a recipe element.

Logging

Object Specification Quantity

Logs Number of logs 2
Number of tags per log 40
Number of log If storage type is File-TXT(Unicode) 1, 200,000
entries If storage type is File-SQLite Database, 2000,000
Number of segmented circular logs 500
Logging cycle 1s
1 The number of entries for all segmented circular logs is valid for the "segmented circular log" logging method. The
product derived from the number of circular logs times the number of data records in this log may not be exceeded.

Flow block

Object Specification Quantity

Flow blocks Number of flow block symbol vertices per screen 2000

Trend views

Object Specification Quantity

Trends Number of trends 30

Table views

Object Specification Quantity

Columns Number of columns 50

Diagnostic views

Object Specification Quantity

Diagnostic views Number of diagnostic views 1

Smart 700 IE V4, Smart 1000 IE V4

84 Operating Instructions, 12/2023, A5E51638950-AC
 Technical specifications
8.11 Scope of functions with WinCC flexible SMART

Data transfer

Object Specification Quantity

Data transfers Number of data transfers 32

Text lists and graphics lists

Object Specification Quantity

Lists Number of graphics lists 100
Number of text lists 200
Number of entries per text or graphics list 50
Number of graphic objects 800
Number of text objects 1500

Safety

Object Specification Quantity

Safety Number of user groups 50
Number of users 50
Number of authorizations 32

Infotexts

Object Specification Quantity

Infotexts Length (no. of characters) 320
For alarms Yes
For screens Yes
For screen objects (for example, for I/O field, switch, button, Yes
invisible button)

Additional functions

Object Specification Quantity

Screen settings Touch screen calibration Yes
Brightness setting No
Language change Number of runtime languages 5
Graphic objects Vector and pixel graphics Yes

Project

Object Specification Quantity

Project file "*.srt" Size 16 MB

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 85
Technical Support A
A.1 Service and support
You can find additional information and support for the products described on the Internet at
the following addresses:
• Technical support (https://support.industry.siemens.com/cs/cn/zh/ps)
• Support request form (http://www.ad.siemens.com.cn/service/SR)
• After-sales information system (http://www.ad.siemens.com.cn/service/)
• Your local representative
(https://www.industry.siemens.com.cn/home/cn/zh/contact/Pages/Default.aspx)
• Training center (http://www.ad.siemens.com.cn/training/)

A.2 System events

System events on the HMI device provide information about internal states of the HMI device
and the PLC.

Note
System events are only indicated if an alarm window was configured. System events are
output in the language currently set on your HMI device.

System event parameters

System events may contain encrypted parameters which are relevant to troubleshooting
because they provide a reference to the source code of the runtime software. These
parameters are output after the text "Error code:".

Description of the system events

A listing of all system alarms for your HMI device is provided in the online help of your
configuration software.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 86
Abbreviations B
CPU Central Processing Unit
CTS Clear To Send
DC Direct Current
DHCP Dynamic Host Configuration Protocol
DP Distributed I/O
DSR Data Set Ready
DTR Data Terminal Ready
IO Input and Output
ESD Electrostatic Sensitive Devices
EMC Electromagnetic Compatibility
EN European standard
GND Ground
HMI Human Machine Interface
IEC International Electronic Commission
IP Internet Protocol
LED Light Emitting Diode
MPI Multi Point Interface
MTBF Mean Time Between Failures
n. c. Not connected
OP Operator Panel
PC Personal Computer
PPI Point-to-Point Interface (SIMATIC S7)
PELV Protective Extra Low Voltage
PLC Programmable Logic Controller
RJ45 Registered Jack Type 45
RTC Real Time Clock
RTS Request to send
RxD Receive Data
SELV Safety Extra Low Voltage
Sub-D Subminiature D (plug)
TCP/IP Transmission Control Protocol/Internet Protocol
TFT Thin Film Transistor
TxD Transmit Data
USB Universal Serial Bus

Smart 700 IE V4, Smart 1000 IE V4

87 Operating Instructions, 12/2023, A5E51638950-AC
Glossary

"Transfer" mode
HMI device operating mode for transferring an executable project from the configuration PC
to an HMI device.

Configuration PC
A configuring PC is a programming device or PC on which plant projects are created using an
engineering software.

Configuration software
The configuration software is used to create projects for process visualization. WinCC flexible
Smart is an example of this type of configuration software.

Event
Incoming events trigger defined functions. Events can be configured. Events which can be
assigned to a button include "Press" and "Release", for example.

Field
Area reserved in configured screens for the input and output of values.

Flash memory
Flash memory is a non-volatile memory with EEPROM chips that is implemented either as
mobile storage medium, or as permanently installed memory module on the motherboard.

Half Brightness Life Time

Time period after which brightness is reduced to 50% of the original value. The specified
value depends on the operating temperature.

HMI device
HMI devices are used to operate and monitor machinery and plants. The machine or plant
states are visualized on the HMI device by means of graphic objects or signal lamps. The
operator controls of the HMI device enable intervention in machine or plant processes and
sequences.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 88
 Glossary

HMI device image

The HMI device image is a file that can be transferred from the configuring PC to the HMI
device. The HMI device image contains the operating system of the HMI device , including the
elements of the Runtime software required for the executable project file.

I/O field
Enables the input or output of values on the HMI device and their transfer to the PLC.

Infotext
A configured infotext provides information about objects within a project. An alarm infotext,
for example, can contain information on the cause and troubleshooting of faults.

Loader
The boot loader is used to start the operating system and is started automatically after power
on of the HMI device.

Object
An object is a project element such as a screen or an alarm. Objects are used to view or enter
texts and values on the HMI device.

Operating element
An operating element is a project component that is used to enter values and trigger
functions. An operating element is a button, for example.

Plant
General term referring to machinery, processing centers, systems, plants and processes
which are operated and monitored using an HMI device.

PLC
PLC is a general term for devices and systems with which the HMI device communicates, e.g.
SIMATIC S7.

PLC job
A PLC job triggers a function at the HMI device.

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 89
Glossary

Process visualization
Denotes visualization of technical processes by means of text and graphic elements.
Configured plant screens enable intervention in runtime plant processes by means of data
input and output.

Project
A project is the result of a configuration using an engineering software. The project usually
contains several screens with embedded system-specific objects, basic settings and alarms.
The project is saved in the project file.
There is a difference between an offline project on a configuring PC and an online executable
project on an HMI device. A project can be available in more languages on the configuring PC
than can be managed on the HMI device. The project on the configuring PC can also be set up
for different HMI devices. However, on the HMI device you can only transfer the executable
project which has been generated specifically for this HMI device.

Recipe
A recipe represent a combination of tags that form a fixed data structure. The configured data
structure can be assigned data in the configuration software or on the HMI device and is then
referred to as a data record. The use of recipes ensures that all data assigned to a data record
is transferred synchronously to the PLC.

Symbolic I/O field

Symbolic I/O fields are used for the input and output of values. A field contains a list of
default entries from which one can be selected.

System alarms
System alarms are assigned the "System" alarm class. A system alarm reports internal states
of the HMI device and of the PLC.

Tags
A tag is a defined memory area that is used to read and write values. Those tags can be
accessed from the PLC or using the HMI device. We distinguish between external tags
(process tags) and internal tags, depending on whether or not the tag is interconnected with
the PLC.

Transfer
Transfer of an executable project from the configuration PC to the HMI device.

WinCC flexible Smart

WinCC flexible Smart is engineering software for configuring Smart panels.

Smart 700 IE V4, Smart 1000 IE V4

90 Operating Instructions, 12/2023, A5E51638950-AC
Index
Date and time settings, 54
Decimal places, 39
A Degree of protection
Protection against ingress of solid foreign bodies, 72
Acoustic feedback, 53
Protection against water, 72
Device Password protection
Deactivating, 56
B
Device Password protection
Backup, 42, 60, 64 Activating, 55
Basic knowledge Dimensions
Required, 4 Smart 1000 IE V4, 74
Smart 700 IE V4, 73
Display
C Setting, 48
Smart 1000 IE V4, 76
Calibrating, 50
Smart 700 IE V4, 76
Care, 66
Disposal, 67
CE approval, 68
Checking
Package content, 18
E
Power supply, 28
Clock Electrical isolation, 28
Smart 1000 IE V4, 77 Electrical potential difference, 25
Smart 700 IE V4, 77 EMC directive, 68
Commissioning engineers, 3 Emission, 15
Compatibility conflict, 64 Equipotential bonding
Compatible PLCs, 79 Conductor, 26
Conductor cross-section Connecting, 26
Equipotential bonding, 26 Requirements, 26
Configuration PC, 58 Wiring diagram, 27
Configuration phase, 58 ESD, 14
Configuring
Network settings, 47
Screen saver, 52 F
Connecting
Feedback
Equipotential bonding, 26
Acoustic, 53
PLC, 31
Figures, 4
Power supply, 28
Functional scope
USB device, 33
Alarm buffer, 83
Connector schematics PLCs, 80
Alarms, 83
Control cabinet
Data transfer, 85
Working on, 13
Diagnostic views, 84
Control Panel
Flow block, 84
Overview, 41
Graphic objects, 85
Graphics lists, 85
Infotext, 85
D
Language change, 85
Data input, 39 Limit value monitoring, 83

Smart 700 IE V4, Smart 1000 IE V4

91 Operating Instructions, 12/2023, A5E51638950-AC
Index

Logging, 84 M
Recipes, 84
Maintenance, 66
Safety, 85
Maintenance technicians, 3
Scaling, 83
Memory
Screen settings, 85
Smart 1000 IE V4, 76
Screens, 83
Smart 700 IE V4, 76
Table views, 84
Mitsubishi connectors
Tags, 83
FX, 81
Text lists, 83, 85
Protocol 4, 81
Trends, 84
Modicon connector, 82
Mounting clips
Inserting, 24
H
Mounting cutout, 21
High frequency radiation, 13 Mounting position, 19
HMI device
Connecting, 24
Mounting, 22 N
Performance features, 82
Network discovery, 53
Shutting down, 35
Non-isolated system configuration, 28
Switching on, 34
System limits, 82
Technical data, 76
O
Testing, 34
Offline
Operating mode, 59
I Test, 63
Omron connector, 82
Illustrations, 4
Online
Initial startup, 58
Operating mode, 59
Input device
Test, 64
Smart 1000 IE V4, 76
Operating instructions
Smart 700 IE V4, 76
Purpose of, 3
Installation
Scope, conventions, 3
Horizontal mounting, 19
Operating mode, 59
Vertical, 19
Changing, 59
Installation as intended, 13
Offline, 59
Installing
Online, 59
HMI device, 22
Transfer, 59
Insulation test, 72
Operating system
Interfaces
Updating, 65
Smart 1000 IE V4, 76
Operators, 3
Subentry, 76
OS Update, 44

L P
Licensing information
Package content
Displaying, 51
Checking, 18
Limit value check, 39
Password protection, 40
List of abbreviations, 87
PELV, 28
Performance features
HMI device, 82

Smart 700 IE V4, Smart 1000 IE V4

92 Operating Instructions, 12/2023, A5E51638950-AC
 Index

Pin assignment Unintentional response, 66

Ports, 77 USB port, 33
PLC connection, 31 Working on the control cabinet, 13
PLCs Safety regulations, 13
compatible, 79 Screen
connector schematics, 80 Setting, 48
Ports Screen keyboard
pin assignment, 77 Key assignment, 38
Power failure, 64 Screen saver, 52
Process control phase, 58 secure boot, 16
Project, 45 Securing device
Offline testing, 63 With mounting clips, 24
Testing online, 64 Service & Commissioning, 42, 43, 44, 45
Service technicians, 3
Shutting down
R HMI device, 35
Start Center
Radiation
Password protection, 40
High frequency, 13
Stripping insulation, 28
Radio interference, 15
Supply voltage
Rated load
Smart 1000 IE V4, 77
USB port, 33
Smart 700 IE V4, 77
Recommissioning, 58
Switching on
Recycling, 67
HMI device, 34
Registered trademarks, 5
System configuration
Regulations for the prevention of accidents, 13
Non-isolated, 28
Remote Password protection
System event
Deactivating, 57
in the online help, 86
Remote Password protection
Parameters, 86
Activating, 57
System information
Restore, 43, 64
Displaying, 49
Restoring, 60
System limits
HMI device, 82
S
S7-200 connector, 80 T
Safe electrical isolation, 28
Technical data
Safety
Display, 76
Standards, 68
Input device, 76
Safety instruction
Interfaces, 76
Compatibility conflict, 64
Memory, 76
Data loss, 65
Supply voltage, 77
Equipotential bonding conductor, 26
Testing
Functional problem, 33
HMI device, 34
General, 15
Touch, 50
High frequency radiation, 13
Trademarks, 5
Operation indoors, 15
Transfer, 58, 59, 60
Power failure, 64
Automatic, 61
Preventing inadvertent operation, 66
Manual, 61
Storage, 70
Project, 58
Transportation, 70
Transfer settings, 52, 53
unauthorized cleaning products, 66

Smart 700 IE V4, Smart 1000 IE V4

Operating Instructions, 12/2023, A5E51638950-AC 93
Index

U
UKCA, 68
Updating
Operating system, 65
Usage
In residential areas, 15
Industrial, 15
With additional measures, 16
USB device
Connecting, 33
USB memory stick
at USB port, 33
USB port
Memory stick not detected, 33
Rated load, 33

W
Weight
Smart 1000 IE V4, 76
Smart 700 IE V4, 76
Working on the control cabinet, 13

Smart 700 IE V4, Smart 1000 IE V4

94 Operating Instructions, 12/2023, A5E51638950-AC