Understanding Insulation

Resistance Testing
Why have an insulation testing program?
A regular program of testing insulation resistance is strongly
recommended to prevent electrical shocks, assure safety
of personnel and to reduce or eliminate down time. It helps
to detect deterioration of insulation in order to schedule repair
work such as: vacuum cleaning, steam cleaning, drying and
rewinding. It is also helpful when evaluating the quality of the
repairs before the equipment is put back into operation.

What causes insulation failure?

Some of the more common causes of insulation failure
include: excessive heat or cold, moisture, dirt, corrosive
vapors, oil, vibration, aging and nicked wiring.

What tests are used to detect insulation deterioration?

There are numerous maintenance tests for assessing
insulation quality. The three tests discussed here are used
primarily to test motor, generator and transformer insulation.

What equipment is necessary for conducting insulation

resistance tests?
• Megohmmeter with a timed test function
• Temperature indicator
• Humidity meter (not necessary if equipment temperature is
above the dew point)

Test Currents in Insulation

Total current in the body of the insulation is the sum of three Insulation Resistance Readings
components Readings are time dependent
• Capacitance Charging Current • at the start, capacitance is what you see first
• Absorption Current • at or about one minute, absorption
• Leakage or Conduction Current • at 10 minutes, reading is mainly leakage current
These changing readings are best seen with analog
Test Currents in Insulation One Line Diagram bargraphs on digital instruments or needle movement
S on analog instruments.
C = Represents
C
charging current Spot Reading Test
RA = Represents Method
absorption For this test, the megohmmeter is connected across the
DC VOLTAGE RL
current
SOURCE
RL = Represents insulation of the windings of the machine being tested.
RA volumetric A test voltage is applied for a fixed period of time, usually
leakage current 60 seconds and a reading is taken. The spot reading test
(dielectric loss) should only be carried out when the winding temperature is
above the dew point1. The operator should make a note of
the winding temperature, so that it will be possible to correct
100
the reading to a base temperature of 20°C.
90
80 CAPACITANCE
70
CHARGING CURRENT
60
50 Test Duration
40
30 To obtain comparable results, tests must be of the same
TOTAL CURRENT
duration. Usually the reading is taken after 60 seconds.
CURRENT – MICROAMPERES

30

25

20

15 Interpretation of Results
Proper interpretation of spot reading tests requires access
10
9
8 to records of results from previous spot reading tests. For
conclusive results, only use results from tests performed at
7
6
5
4
CONDUCTION
the same test voltage for the same amount of time, and under
3
OR LEAKAGE
CURRENT ABSORPTION
similar temperature and humidity conditions. These readings
2.5

2
CURRENT
are used to plot a curve of the history of insulation resistance.
1.5 A curve showing a downward trend usually indicates a loss of
1 insulation resistance due to unfavorable conditions such as:
.1 .15 .2 .25 .3 .4 .5 .6 .7 .8 .9 1.0 1.5 2 2.5 3 4 5 6 7 8 9 10

SECONDS
humidity, dust accumulation, etc. A very sharp drop indicates
an insulation failure. See Figure 1.
Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 1 of 6

 10000 A heavy-duty megohmmeter serves this need. Similarly,
such an instrument is better adapted for cables, bushings,
transformers, and switchgear in the heavier-duty sizes.

Test Methods – Time-Resistant Tests Dielectric Absorption

1000
Ratio (DAR)
C • The ratio of 60 seconds/30 seconds
Reading in Megohms

➞
• less than 1 = failed
• 1.0 to 1.25 = OK
100
➞A • 1.4 to 1.6 = excellent
Note: This is not a commonly used test

10 Step Voltage Test

Method
In this test, the operator applies two or more test voltages in
B➞ steps. The recommended ratio for the test voltage steps is
1
1996 1997 1998 1999 2000 2001
1 to 5. At each step, test voltage should be applied for the
Date of Test same length of time, usually 60 seconds. The application of
increased voltage creates electrical stresses on internal
Figure 1 insulation cracks. This can reveal aging and physical damage
Example of the variation of insulation resistance over a period of years:
even in relatively dry and clean insulation which would not
At A, the effect of aging and dust accumulation is shown by decreasing values.
At B, the sharp drop indicates an insulation failure.
have been apparent at lower voltages.
At C, the insulation resistance value after the motor has been rewound.
(1) Dew point temperature is the temperature at which the moisture vapor in the
Test Duration
air condenses as a liquid. A series of “steps,” each step lasting 60 seconds.

Interpretation of Results
Time-Resistance Testing Method Compare the readings taken at different voltage levels, look-
This method is fairly independent of temperature and often ing for any excessive reduction in insulation resistance values
can give you conclusive information without records of past at the higher voltage levels. Insulation that is thoroughly dry,
tests. It is based on the absorption effect of good insulation clean, and without physical damage should provide roughly
compared to that of moist or contaminated insulation. the same resistance values despite changes in test voltage
Simply take successive readings at specific times and note levels. If resistance values decrease substantially when tested
the differences in readings (see curves, Figure 2). Tests by at higher voltage levels, this should serve as a warning that
this method are sometimes referred to as absorption tests. insulation quality may be deteriorating due to dirt, moisture,
cracking, aging, etc.
Good insulation shows a continual increase in resistance
(see curve D) over a period of time (in the order of 5 to Polarization Index (PI) = 10-minute reading
10 minutes). This is caused by the absorption; good 1-minute reading
insulation shows this charge effect over a time period much
The IEEE Std 43-2000 lists the following minimum values for
longer that the time required to charge the capacitance of the polarization index for AC and DC rotating machines:
the insulation.
Class A: 1.5 Class B: 2.0 Class C: 2.0
If the insulation contains moisture or contaminants, the
absorption effect is masked by a high leakage current 1000 D➞
which stays at a fairly constant value – keeping the resist-
ance reading low (R = E/I) (see curve E).
Reading in Megohms

The time-resistance testing is of value because it is

independent of equipment size. The increase in resistance 100
➞

for clean and dry insulation occurs in the same manner E

whether a motor is large or small. You can compare several
motors and establish standards for new ones, regardless of
their horsepower ratings. 10

Figure 2 shows how a 60-second test would appear for good

and bad insulation. When the insulation is in good shape, the
60-second reading is higher that the 30-second reading. 1

1 2 3 4 5 6 7 8 9 10
A further advantage of this two reading test is that it gives Time in Minutes

you a clearer picture, even when a “spot reading” says the Figure 2
insulation looks ok. Absorption curve of test conducted on 350 HP Motor: Curve D indicates a
good insulation with an excellent polarization index of 5. Curve E indicates a
Time-resistance tests on large rotating electrical machinery potential problem. The polarization index is only 140/95, or 1.47.
– especially with high operating voltage – require high (2) IEEE Std. 43-2000, “Recommended Practice for Testing Insulation
insulation resistance ranges and a very constant test voltage. Resistance of Rotating Machinery.” Available from the Institute of Electrical and
Electronics Engineers, Inc., 345 E. 47th St., New York, NY 10017.

Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 2 of 6

 No Connection to To Guard
Guard Terminal Terminal

B B
1 I1

Ay Ay

Rz Rz

To EARTH Rx To LINE To EARTH Rx To LINE

Terminal Terminal Terminal Terminal
A C A C
i i

Advantages of DC Testing
• Lighter size and weight of test equipment
• Non-destructive
• Historical data can be compiled

Before and after repair:

Curve F shows a downward trend of insulation resistance values as the test
Transformer Testing
voltage is increased. This indicates a potential problem with the insulation.
Transformers are tested at or above the rated voltage to
Curve G shows the same equipment after it has been repaired. be certain there are no excessive leakage paths to ground
or between windings. These are conducted with the
transformer completely disconnected from the line and
Utilizing the Guard Terminal load. However, the case ground should not be removed.
The guard terminal is useful when measuring very high
resistance values. Single-Phase Transformer
The following 5 tests and corresponding wiring diagrams
will completely test a single-phase transformer. Allow at
least 1 minute for each test or until the reading stabilizes.

a. High voltage winding to low voltage winding and ground

b. Low voltage winding to high voltage winding and

ground

The guard terminal c. High voltage winding to low voltage winding

is useful when
d. High voltage winding to ground
measuring very
Conductor Insulation Shield Exposed high resistance e. Low voltage winding to ground
to to to Surface values.
Line (–) Guard Earth (+)
Terminal Terminal Terminal Three-Phase Transformer
The following 5 tests and corresponding wiring diagrams
will completely test a three-phase transformer.

What test voltage should I use? a. High voltage winding to low voltage winding
There are two schools of thought regarding the voltage to test and ground
insulation at. The first applies to new equipment or cable and
b. High voltage winding to ground with low voltage
can use AC or DC test voltages.
winding to guard
When AC voltage is used, the rule of thumb is 2 x nameplate c. High voltage winding to low voltage winding
voltage + 1000. When DC voltage is used (most common on
megohmmeters manufactured today) the rule of thumb is d. Low voltage winding to ground and high voltage
simply 2 x nameplate voltage except when higher voltages winding to guard
are used. See chart below for suggested values. e. High voltage winding to low voltage winding
Equipment/Cable Rating DC Test Voltage
24 to 50V 50 to 100VDC
50 to 100V 100 to 250VDC
100 to 240V 250 to 500VDC
440 to 550V 500 to 1000VDC
2400V 1000 to 2500VDC
4100V 1000 to 5000VDC

It is always advisable to contact the original equipment

manufacturer to get their recommendation for the proper
voltage to use when testing their equipment.

Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 3 of 6

 Single-Phase Transformer Three-Phase Transformer

X3 H1

X2 X3 H3

X1 H2 X2 H2
a. High voltage winding
X1 H1 to low voltage winding
and ground
X0
a. High voltage winding
to low voltage winding
and ground

X3 H1

X2
X3 H3

X1 H2
X2 H2 b. High voltage winding
to ground with low
X1 H1
voltage winding to
X0
guard
b. Low voltage winding
to high voltage winding
and ground

X3 H1

X2 X3 H3

X1 H2 X2 H2

X1 H1 c. High voltage winding

to low voltage winding
X0

c. High voltage winding

to low voltage winding

X3 H1

X2 X3 H3

X1 H2 X2 H2 d. Low voltage winding

to ground and high
X1 H1 voltage winding
to guard
X0

d. High voltage winding

to ground

X3 H1

X2 X3 H3

X1 H2 X2 H2
e. High voltage winding
X1 H1 to low voltage winding

X0

e. Low voltage winding

to ground

= Earth Terminal = Line Terminal G = Guard Terminal

Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 4 of 6

Cable Testing Motor and Generator Testing
Transformers are tested at or above the rated voltage to Before testing the above lift the rotor brushes, ground the
be certain there are no excessive leakage paths to ground starter terminal and frame and ground the motor shaft.
or between windings. These are conducted with the Discharge the field winding by grounding. Then remove
transformer completely disconnected from the line and the field winding from ground and connect to the (-) Line
load. However, the case ground should not be removed. connection on the megohmmeter. Connect the (+) Earth
terminal to ground. The diagram shows the connection for
Single Conductor testing the field insulation resistance. The stator winding
Connect as shown in the diagram may also be measured in a similar manner.
a. Conductor to Line (-) terminal and sheath to Earth (+)

Multi-Conductor
a. Single conductor Stator

b. One conductor to all

c. One conductor to earth
d. One conductor to others minus ground T4 T5 T6

T1 T2 T3 N

Insulation Conductor

ƒ1 ƒ2
Field
Ground Sheath – single conductor
a. Single conductor

Three-conductor
cable

b. One conductor to all

= Earth Terminal = Line Terminal G = Guard Terminal

© 2002 Chauvin Arnoux®, Inc. d.b.a. AEMC ® Instruments

c. One conductor to earth

Three-conductor
cable

d. One conductor to others minus ground

Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 5 of 6

Contact Us
United States & Canada:

Chauvin Arnoux®, Inc.

d.b.a. AEMC ® Instruments
200 Foxborough Blvd.
Foxborough, MA 02035 USA
(508) 698-2115 • Fax (508) 698-2118
www.aemc.com

Customer Support – for placing an order, obtaining price & delivery:

[email protected]

Sales Department – for general sales information:

[email protected]

Repair and Calibration Service – for information on repair & calibration, obtaining a user manual:
[email protected]

Technical and Product Application Support – for technical and application support:
[email protected]

Webmaster – for information regarding www.aemc.com:

[email protected]

South America, Central America, Mexico, Caribbean, Australia & New Zealand:

Chauvin Arnoux®, Inc.

d.b.a. AEMC ® Instruments
15 Faraday Drive
Dover, NH 03820 USA
(978) 526-7667 • Fax (978) 526-7605
[email protected]
www.aemc.com

All other countries:

Chauvin Arnoux SCA

190, rue Championnet
75876 Paris Cedex 18, France
33 1 44 85 45 28 • Fax 33 1 46 27 73 89
[email protected]
www.chauvin-arnoux.com

Understanding Insulation Resistance Testing (pdf) 02/06 Rev. 02

Technical Assistance (800) 343-1391 6 of 6