Jinan Remax Machinery Technology Co.

,Ltd

Remax CNC Router

User’s Operation Manual

JINAN REMAX MACHINERY TECHNOLOGY CO.,LTD.

 Jinan Remax Machinery Technology Co.,Ltd

Content
Content…………………………..............…………1

Ⅰ. Introduction of wiring of CNC router..........….2

Ⅱ.Install control software…………..........………..2

Ⅲ. Introduction of Software………................…….5

Ⅳ. Description of software menus…...............……17

Ⅴ. Operation procedures……………….................22

Ⅵ.Attachment: List of Shortcuts………...........…..25

1
 Jinan Remax Machinery Technology Co.,Ltd

Welcome to use CNC router.

For safe operation and operation, please ground CNC router safely!
1. Grounding of CNC router body.
2. Grounding of control box of frequency converter.

Ⅰ. Introduction of wiring of CNC router

Rear ends of control box of CNC router connect with X and Y (two pieces), Z, frequency
converter, limit switch and external power source (AC 220V) separately. Front panel
connects signal wire, another end of signal wire connects control panel interface on the
computer.

Ⅱ.Install control software

After finishing wiring of engraver, we start to install control software of CNC router.
(ARTCUT software, graphic and text design software for engraver, has detailed description
on its software, so no further introduction is made here).
After finishing software installation, insert PCI control card into PCI slot of the computer.
After placing control software into CD-ROM, operate SETUP. EXE file for installation,
shown as following diagram:

2
 Jinan Remax Machinery Technology Co.,Ltd

Press NEXT to select installation catalogue.

fter selecting installation catalogue, press NEXT.

3
 Jinan Remax Machinery Technology Co.,Ltd

Press NEXT.

Press NEXT.

4
 Jinan Remax Machinery Technology Co.,Ltd

Press NEXT until finishing installation. Then turn off the computer and insert PCI control
card into PCI slot of the computer. Start the computer again, the computer will automatically
install driver program.

Ⅲ. Introduction of Software
After the computer starts, start NCSTUDIO from desktop of the computer, following
interface will display.

5
 Jinan Remax Machinery Technology Co.,Ltd

Ncstudio™ interface consists of title bar, menu bar, tool bar, status bar and some function
windows.

Operation modes and status

Operation mode

At any moment during user’s operation on the machine, it is in one of following operation
modes.
Automatic mode
Under automatic operation mode, machine movement functions by prior prepared processing
program. Therefore, the system shall be loaded processing program under automatic mode.
Jog mode
It is one of manual operation mode. Under jog mode, the user controls the machine by
manual operation device, for example, computer keyboard. When the user gives out
movement signal by these devices, for example, press down manual button, the machine

6
 Jinan Remax Machinery Technology Co.,Ltd

continues movement until the signal disappears.

Increment mode
It is one of manual operation mode. Use computer keyboard to control the machine. The
difference between jog control mode and increment mode is the machine only moves defined
distance by one pressing operation of the user, i.e. from pressing to releasing. That is to say,
the user can accurately control displacement of the machine by increment mode.

Operation status

Each operation mode can be divided into several operation status, both operation modes and
operation status completely define the status of the machine.
Idle state
It is the most common state. Under this state, the machine hasn’t any action output at present
and is ready for receiving new start and for starting new action.
Locking state
Locking state is a kind of internal state and normally generates at state switchover, so the
user can’t contact it under normal situations.
Operation state
When the machine is implementing any action, the system enters operation state.
Pause state
When the machine moves, if the user implements “operation | pause” command or the
system receives MO1 (ready command), then the system enters pause state and waits for
further enter by the user, the user can continue to implement by implementing “operation |
start”.

Function window is divided into three areas, including:

The first area: Digital control state window.
The second area: Processing locus, system log, program management, system parameter,
programming and I/O state window.
The third area: Automatic operation window and manual operation window.

Title bar

Title bar is on the topmost end of Ncstudio™ software interface and is used for displaying

7
 Jinan Remax Machinery Technology Co.,Ltd

software name and loading processing program name; colors of title bar are used for
indicating whether corresponding windows are enabled.

Note:
In default setting of Windows, color of title bar of active window is

blue; color of title bar of non-active window is gray.

Digital control state window

Coordinate display window is at upper part of the screen and displays current position, feed
speed and feed rate adjustment of principal axis (cutting tool).

Processing status and time information

Title bar of digital control window also displays some state information. As shown in above
diagram, for example, during the system emulates, title bar displays “emulation mode” text,
estimated implementation time (calculating by 100% feed rate) also displays at right side of
title bar. During actual processing, actual processing time displays at the right side.

8
 Jinan Remax Machinery Technology Co.,Ltd

Current position

For the convenience of describing various positions, Ncstudio™ displays two sets of
coordinate systems of mechanic coordinate system and work piece coordinate system at the
same time.

The system supplies the method for convenient setting and revising base point of work piece:
Set current point as base point of work piece, that is to say, zero relative position of single
axis. Move the cursor to coordinate display area of this axis and click left key of mouse, then
coordinate of this axis can become 0. If needing set all current positions of three axes into 0,
only need click in various coordinate areas.

Prompt:

Another method for zeroing all work piece coordinates is to select the

manual “operation (O) | setting current point as work piece base point

(Z)…” or to select equivalent tool bar button.

Feed speed

Various information such as setting speed, transient speed, speed scale factor and current line

(paragraph) number displays in feed speed area. Speed setting value and feed rate can be also

revised.

 Feed rate slide bar: Dragging slide bar can adjust current movement speed within

the range of 0~120%. Feed rate displays in the form of percentage.

 Setting value: Setting value of feed speed is also the value given by parameter F

in command G.

9
 Jinan Remax Machinery Technology Co.,Ltd

 Actual value: Transient value of feed speed. It changes with setting value, current

acceleration or deceleration state and feed rate.

 Current line (paragraph) number: It displays paragraph number or line number

of current implementation code.

When the system is at idle state, click setting value, and then speed setting dialog box pops
up. When the system is at automatic state, popup dialog box is used for setting default speed
of automatic operation.

When the system is at manual state, popup dialog box is used for setting speed of manual
operation, shown as following diagram:

Automatic operation window

Automatic operation window displays current opening processing file. Ncstudio™ supports
two processing program formats of command G format and HP PLT format at present. The
user can view current processing program by this window.

10
 Jinan Remax Machinery Technology Co.,Ltd

Manual operation window

Manual window supplies an interactive operation environment for controlling machine by

manual way to the user.

11
 Jinan Remax Machinery Technology Co.,Ltd

Since manual window is at function window area of main window, the method for the user to
switchover several windows and to activate manual window is:

Manual button area in this window includes six manual buttons that correspond to positive
and negative directions of axes X, Y and Z respectively.
Manual operation of the machine has two ways: Continuous jog way and increment stepping
way that are respectively introduced as following:
Continuous jog way
Under continuous jog way, when manual window is current active window, press
corresponding numerical key on the keypad. When the key is at pressing state, the machine
acts; when the key is released, the machine stops action.

When implementing jog action, track window displays track locus by color of command
G00.
Increment stepping way
It is similar to manual way. The difference between continuous jog way and increment
stepping way is increment stepping way can accurately control feed speed of machine
kinematical axis.
The user can implement increment stepping operation by mouse and keyboard through
interactive interface and can also implement this operation by manual operation panel or

12
 Jinan Remax Machinery Technology Co.,Ltd

operation box. Touching manual button every time can correspond to given step length of
axis movement.

Keyboard way
When jog window is current active window, increasing or decreasing jog step length by
direction key can see change of jog step length button.

Mouse way
Directly use mouse to click suitable step length button.
Note:

Avoid setting too large jog step length so as not to damage the

machine by misoperation.
Mouse way
Use left key of mouse to click the button, then the button is triggered once.
Note:

Since implementing jog command by the system each time needs

certain time, so too frequent clicking may cause the system to prompt

error information that “equipment is busy and current operation is

invalid”.
Increase/decrease depth
Using +/-keys on the keypad and digital keys can quickly increase and decrease depth.

System parameter window

System parameters include two types: Processing parameters and producer parameters.

Their various parameters are explained in detail as following.

1. Processing parameters

Ncstudio™ processing parameters are set as following:

13
 Jinan Remax Machinery Technology Co.,Ltd

Manual speed: It includes manual high speed and manual low speed. These two values are
used for movement speed under “jog” mode.
 Manual low speed refers to movement speed when only pressing manual
direction key;
 Manual high speed refers to movement speed when pressing “high speed” key at
the same time.
These two values can be also set directly under digital control state window. Automatic
parameters:
 Idle running speed: Movement speed of command G00;

 Processing speed: Interpolation speed of processing commands G01, G02, G03

and so on.

These two values control movement speed under automatic mode. If processing program or

command MDI doesn’t define the speed, then the machine moves by here setting speed.

Note:

Movement speed by increment way is idle running speed.

 Using default speed: Whether to abandon the speed specified in processing

14
 Jinan Remax Machinery Technology Co.,Ltd

program and to use above setting system default speed.

 Speed self adoption and optimization: Whether to allow the system to optimize

processing speed according to connection feature of processing work piece.

 IJK increment mode: Whether circle center programming (IJK) is increment

mode and IJK value used by arc programming for some post processing

programs is increment value. Refer to descriptions on corresponding

post-processing programs for this point.

 Using tool-lowering speed in direction Z: Whether to use specific tool-lowering

speed during vertical downward movement in direction Z.

 Optimizing tool-raising speed in direction Z: Whether to use G00 speed to raise

tool during vertical upward movement in direction Z.

 Idle running (G00) command uses fixed feed rate 100%: This parameter is an

option. It shall direct the system whether to neglect influence of feed rate when

implementing idle running command. Idle running speed will not be influenced

when changing the rate by this way.

 During pausing or ending, automatically stop principal axis (need restart): Setting

whether to automatically stop rotation of main axis when one processing

program pauses or after ending processing.

 Mirror axis X: Setting making mirror image for axis X.

 Mirror axis Y: Setting making mirror image for axis Y.

Tool change position parameters:

 Using tool change position: Please select this option if automatic return to certain

position is required after ending processing.

Other tool change position parameters can function only when using tool change

position is enabled.

 Mechanic coordinates X, Y and Z of tool change position: Setting mechanic

coordinates of tool change position (note: not coordinates of work piece!).

Tool return point parameters:

Tool return point: Tool raising height (in relation to base point of work piece) when

returning base point and break point of work piece for continuous operation.

15
 Jinan Remax Machinery Technology Co.,Ltd

File input parameters:

 2D PLT processing depth: Setting tool depth when loading PLT file processing.

 Tool-raising height: Setting tool-raising height during PLT file processing.

 PLT unit per mm: Setting PLT unit value.

 Reverse axis Z: Setting whether to use reverse function of axis Z. Default of the

system is the part above axis is positive.

2. Producer parameters

The user doesn’t contact “producer parameters” that needs input password (ncstudio) when
contacting. This is only for avoiding any system failure caused by changing these important
parameters accidentally by the user.

16
 Jinan Remax Machinery Technology Co.,Ltd

Workbench dimensions:
Please make setting according to above parameters so as to avoid any possible damage
caused by impacting limit switch or hard limit.
Note:

This value has been set before out of factory; don’t revise it!

Mobile calibrator parameters:（a block for cutting tool）

 Thickness of mobile calibrator: Please accurately measure thickness of mobile

calibrator and fill it here.

Motor parameters:

 Pulse value: It refers to minimum displacement that can be processed by

movement control card. In stepping system, it normally corresponds one

stepping pulse and changes angle displacement of stepping pulse into linear

displacement according to transmission relation.

 Start-up speed: This parameter corresponds start-up frequency of stepping motor.

17
 Jinan Remax Machinery Technology Co.,Ltd

Acceleration: The system uses tow acceleration parameters to define acceleration capacity of
movement:
 Single axis acceleration: It is used for describing acceleration and deceleration

capacity of single feed axis.

 Curve bend acceleration: It is used for describing acceleration and deceleration

capacities of multiple feed axes during linkage.

Input/output state (I/O state) window

It is very helpful for system monitor and failure diagnosis. Press and hold three keys of
SHIFT, CTRL and ALT, use right key of mouse to click the direction or limit to be revised,
select and change polarity, then turn on or off relevant functions.

18
 Jinan Remax Machinery Technology Co.,Ltd

Ⅳ. Description of software menus

“File” menu includes command options for controlling file.

Former two options of this pulldown menu are used for “loading” and “unloading” of
program file. Medium seven options are used for editing program file. The file opened by
editing function displays in edit window. Please note the differences between “loading”
function and “unloading” function.

“Edit” menu

“Edit” menu has menu options for editing window. This menu option will change with
current active window in the second window area, since these windows may have some
specific editing functions.

19
 Jinan Remax Machinery Technology Co.,Ltd

“Operation”menu

Various operations can be realized in “operation” menu, but the menu doesn’t include

control for direction output (M function) feed rate and principal axis, these functions

are in “machine” menu.

Limit release

This function is a means for masking limit function when the system meets hard limit and for
restoring normal position of machine when using manual operation. Since limit function is
masked at this moment, so the operator shall pay special attention to use this function.

This menu operation enables and disables single step processing mode. Once “single section
implementation” is enabled, processing program enters pause mode when implementing each
section.

Setting current point as base point of work piece

Select menu option “setting current point as base point of work piece”, this can set work
piece coordinates at current point as zero, this actually doesn’t cause actual position
movement.

Setting work piece coordinates at current point…

This function allows the user to set work piece coordinates at current point conveniently.
Selecting this menu option can change coordinates of current tool position. After selecting
this menu option, the system will pop up dialog box “setting work piece coordinates at
current point”.

Input suitable values into corresponding edit boxes of axes X, Y and Z, then coordinates of
current position are changed.

20
 Jinan Remax Machinery Technology Co.,Ltd

Returning base point of work piece…

Base point of work piece is base point of work piece coordinate.

After selecting the option “returning base point of work piece…” tool tip will automatically
return base point of work piece from current position in the sequence of Z, X and Y.
Since Z coordinate of final point is always on processing surface of work piece, in order to
avoid damaging work piece surface or tool tip caused by tool tip returning to zero point of
work piece, in fact, axis Z doesn’t return to zero point, but it returns to deflection value
above zero point. This value is set by “tool return point” in processing parameter of “system
parameter window”.

Saving base point of work piece

The user can save frequent using base point of work piece as presetting value; 10 sets of
coordinate data can be saved in total.

Reading base point of work piece

Read presetting coordinate value of base point of work piece, quickly return to read
presetting base point of work piece. After reading base point of work piece, use the
command “base point of work piece” to return to presetting base point of work piece.

Starting

This menu option has two functions:

The first function: If certain processing program is loaded and current system state is “idle”,
after selecting this menu option, the machine will automatically start to implement automatic
processing procedure from the first sentence of processing program. Once processing starts,
the system enters “automatic | operation” static; if the system is at emulation state, it
implements processing procedure by emulation state.
The second function: If the system is at “automatic | pause” state, after selecting this menu
option, the system will continue automatic processing procedure from pause position and
enters “automatic | operation” static. If the system is at emulation state, it implements
processing procedure by emulation state.

Prompt:

21
 Jinan Remax Machinery Technology Co.,Ltd

The system has two routes for entering “pause” state: The first one

is the system is at “singe step processing” mode at present; the second

one is the user selects “pause” function during processing procedure.

Pause

During automatic processing procedure, “pause” function is enabled. Then enter “automatic |
pause” state. Select “start” menu option if needing continue processing procedure.
If the system is at emulation state, after selecting “pause” menu option, the system will pause
emulation and enter “automatic | pause” state. Select “start” menu option if needing
continue emulation.

Stop

During automatic processing procedure, i.e., the system is at “automatic | pause” state,
“pause” function is enabled. Select this menu option at this moment, the machine will stop
processing and raise tool, whole processing task ends, then the system enters “automatic |
idle” state, this is the method for making the system normally stop processing procedure
during processing procedure.
Following contents describe, “reset” function that is the method for abnormally stopping
processing procedure used under abnormal situation.
If the system is at emulation state, after selecting “stop” menu option, the system will pause
emulation and enter “automatic | idle” state, but it will not exit emulation state, its function
is to allow the user to analyze emulation results. If the user also needs repeat policy, he can
implement various menu options such as “start”, “advanced start” and “break point continue”
to continue emulation.

Entering emulation and starting emulation

It is similar to “start” menu. If certain processing program is loaded and current system state
is “idle”, after selecting this menu option, the machine will automatically high speed
emulation from the first sentence of processing program. Emulation function is similar to
demonstration function, but is better than demonstration function.
Emulation supplies a quick and vivid simulation-processing environment to the user.
When operating processing program under emulation way, the system will not drive the
machine to make corresponding mechanic and electric actions, but it will only display

22
 Jinan Remax Machinery Technology Co.,Ltd

tool-processing route in high speed on track display window. The user can understand
movement form of the machine in advance by emulation, avoid damaging the machine
caused by fault when preparing processing program and know other additional information.
Once emulation process starts, this menu option becomes “stopping emulation and exiting
emulation mode”, after implementing this function, emulation will stop immediately.

Advanced start

This function realizes skipping implementation function of program.

Break point continue

Function of this menu option actually is a simplified edition of “advanced start”. The system
continues from last processing break point by implementing this function.
This function can be also used for implementing emulation.

Implementing processing command…

When implementing this menu option, the system will pop up dialog box “implementing
processing command” as following diagram:

23
 Jinan Remax Machinery Technology Co.,Ltd

Fine adjustment

This function is enabled only in pause state during automatic processing procedure. It is used
for realizing fine adjustment of depth without stopping processing procedure. Its operation
interface is similar to manual window:

Tool calibration

The user can conveniently define suitable coordinate in direction Z of base point of work
piece and calibrate the coordinate again after changing tool by using tool calibration function.
When implementing this function, select tool calibration function from the menu.
When making tool calibration, firstly define processing surface manually, set processing
surface as base point of work piece in direction Z, then make tool calibration for the first
time. After changing tool each time, make tool calibration for the second time.

24
 Jinan Remax Machinery Technology Co.,Ltd

Ⅴ. Operation procedures

1. Starting-up

Before starting-up, firstly ensure all connections between the machine and the computer are
normal, and then turn on power supply of the machine and the computer. After the system
finishes starting-up, it enters Ncstudio™ digital control system.

2. Mechanic resetting (option)

The contents are involved only for the machine with the function of returning mechanic base
point; please refer to the manual of the machine.
If the machine supports the operation of returning mechanic base point, select “returning
mechanic base point” menu. The machine will automatically returns mechanic base point
and calibrate coordinate system of calibration system.
Under certain situations, for example, after last normal stop, turn on the machine again and
continue last operation, the user doesn’t need implement mechanic resetting operation, since
Ncstudio™ system saves current coordinate information during normal exit.
Furthermore, the user doesn’t need implement this operation if the user ensures current
position is correct.

3. Loading processing program

Before starting processing, the user shall normally load required processing program,
otherwise some functions relevant with automatic processing are disabled.
After selecting the menu “open (F) | open (O)…” dialog box of Windows standard file
operation will pop up, select the driver, route and file name of the file to be opened from this
dialog box.
After clicking “open” button, processing program is loaded into the system. At this moment,
the user can press F2 key to switch over “processing program” window and to view current
processing program.

4. Manual operation

Displaying manual operation interface

After selecting menu option “view (V) | display manual interface (M)”, parameter display
window will display manual operation interface. You can make manual operation on the
machine by this interface by referring to Section 5.2.
Manual movement
Make manual movement on the machine by using corresponding keys on digital keypad of
the computer. NUMLOCK light on the keypad will turn on at this moment.
Corresponding keys are:

25
 Jinan Remax Machinery Technology Co.,Ltd

６ —Positive direction of axis X

４ —Negative direction of axis X
８ —Positive direction of axis Y
２ —Negative direction of axis Y
９ —Positive direction of axis Z
１ —Negative direction of axis Z
Manual high-speed movement of the machine can be realized by combining these keys and
CTRL key.
Increase/decrease depth
Using +/- keys on the keypad and digital keys can quickly increase and decrease depth.

5. Defining base point of work piece

Base point of three coordinates X, Y and Z in processing program is base point of work piece.
Before making processing, we need connect this position with actual position. The
procedures are:
Manually make axes X and Y of the machine move base point position of work piece, select
the menu “setting current point as base point of work piece” or zero coordinate values of
current position in coordinate window, then make processing by using current position as
starting point when implementing processing program.
Above procedure finishes base point of work piece on axes X and Y, but setting base point of
work piece on axis Z needs more accurate operation means. The system and machine
hardware together supply the function of tool calibration on axis Z.
Select the function “operation (O) | automatic tool calibration (E)… ” And finish automatic
tool calibration.
After finishing above two procedures, base point of work piece for processing is defined.

6. Implementing automatic processing

Automatic processing refers to the machine automatically makes processing according to

selected processing program.
Starting automatic processing
After selecting menu option “operation (O) | start or continue (S)”, the machine will
automatically start automatic processing procedure from the first sentence of processing
program
Machine stop
During automatic processing procedure, if processing program is required for stopping,
select menu option “operation (O) | stop (O)”, the machine will stop processing after
finishing processing of current sentence and enter “idle” state. This method is the method for
allowing the system to stop accurately and orderly and is also recommending method.

Note:

26
 Jinan Remax Machinery Technology Co.,Ltd

When connection feature of high and smooth speed is enabled, the

system will stop when link speed is zero.

Machine emergency stop

During automatic processing procedure, select menu option “operation (O) | emergency stop
(B)” if any emergency situation happens, the machine will stop processing immediately. If
needing processing again, firstly select the menu “operation (O) | emergency restore (R)” and
select the menu “operation (O) | start or continue (S)”, the machine will implement automatic
processing procedure from the first sentence of processing program, otherwise the machine
can’t operate.
Machine pause
During automatic processing procedure, if needing processing pause, select menu option
“operation (O) | pause (P)”, the machine will stop processing after finishing current
processing sentence, only select menu option “operation (O) | start or continue (S)” if
needing continue processing program.
Program skipping implementation
After selecting menu option “advanced start (A)”, a dialog box will pop up to inquire starting
from which sentence of program and ending at which sentence of program. If you fill in
sentence paragraph number and click “start” key, the machine will only implement certain
sentence of program according to your requirement, but paragraph number shall be before
sentence of program when implementing this function.

7. Direction positioning function

If you want to position certain point quickly, try “direct positioning function”.

Shortcut key of “direct positioning function” is F5; Shortcut key of exiting “direct
positioning function” is Esc.
Inputting signal + before X in “direct positioning function” window can realize increment
input.
Inputting signal * before X in “direct positioning function” window can realize mechanic
coordinate positioning.
Inputting signal + @ before X in “direct positioning function” window can realize the
function of revising base point of work piece (including increase/decrease depth).

Ⅵ.Attachment: List of Shortcuts

27
 Jinan Remax Machinery Technology Co.,Ltd

1. Overall shortcuts

ESC Switchover between various windows

TAB Switchover between various controls
Ctrl+TAB Switchover between various folding windows
Ctrl+1 Display automatic window
Ctrl+2 Display manual window
Alt+1/F4 Display processing locus window
Alt+2 Display system lag window
Alt+3 Display program management window
Alt+4 Display system parameter window
Alt+5 Display program edit window
Alt+6 Display I/O state window
Ctrl+Enter Full screen
Ctrl+Del Clear processing locus window
Ctrl+O Open and load
Ctrl+N New processing program
Ctrl+E Open and edit
Ctrl+P Edit current processing program
Ctrl+S Save
Ctrl+I Processing program information
F5 Direct positioning
F6 Set coordinate of work piece at current point
Shift+F6 Set current point as base point of work piece
F7 Return base point of work piece
Ctrl+F7 Floating tool calibration
Shift+F7 Fixed tool calibration
F8 Enter (exit) emulation
F9 Start
Ctrl+F9 Advanced start
Shift+F9 Break point continue
Ctrl+Shift+F9 Implement processing command
F10/Pause Break Pause
F11 Stop
F12 Reset

28
 Jinan Remax Machinery Technology Co.,Ltd

2. Manual window shortcuts

ScrollLock Activate manual window

4 (keypad) X-direction manual (including jog and
increment)
6 (keypad) X+ direction manual (including jog and
increment)
2 (keypad) Y- direction manual (including jog and
increment)
8 (keypad) Y+ direction manual (including jog and
increment)
1 (keypad) Z- direction manual (including jog and
increment)
9 (keypad) Z+ direction manual (including jog and
increment)
+ (keypad) Increase depth (input number)
- (keypad) Decrease depth (input number)

3. Processing locus window shortcuts

Home Center
End Display current processing point
. or > Zoom up
, or < Zoom down
. (keypad) Switchover step lengths
Alt+→ or Alt+← Rotate around axis Z
Alt+↑or Alt+↓ Rotate around axis X
Alt+PgUp or Alt+PgDn Rotate around axis Y

29
Jinan Remax Machinery Technology Co.,Ltd

30