Local regulations may restrict the use of this product to below the conditions quoted.

In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2023

TI-P160-02
CMGT Issue 13

Fig 36
Austenitic Stainless Steel
Strainer
Description
The Fig 36 is an austenitic stainless steel integrally flanged Y-type strainer. The standard stainless steel screen in the DN15 to DN80
size range has 0.8 mm perforations, in the DN100 to DN200 size range it has 1.6 mm perforations. Other perforations, mesh sizes and
monel screens are available as options. The strainer cap can be drilled and tapped for blowdown and drain valves if required.

Standards
This product fully complies with the requirements of the EU Pressure Equipment Directive/UK Pressure Equipment (Safety)
Regulations and carries the / mark when so required.

Certification
The product is available with a manufacturers' Typical Test Report
as standard and EN 10204 3.1 for body and cap by special
request.
Note: All certification/inspection requirements must be stated at
the time of order placement.

Sizes and pipe connections

DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80, DN100,
DN125, DN150 and DN200
Standard flange:
EN 1092 PN16, PN25 and PN40 (DN15 to DN50)
EN 1092 PN25 and PN40 (DN65 to DN150)
EN 1092 PN40 (DN200)
ANSI Class 150 and ANSI Class 300 (All sizes)
JIS/KS flanges are available on request.

Optional extras
1.6 mm (DN15 to DN80)
Perforations
Stainless steel screens 3.0 mm (DN15 to DN200)

Mesh 40, 100, 200

Strainer screens 0.8 mm (DN15 to DN80)

Perforations 1.6 mm (DN100 to DN200)

Monel screens
3.0 mm (DN15 to DN200)

Mesh 100

Strainer size Blowdown valve Drain valve

DN15 ¼" ¼"

Blowdown or drain valve
connections DN20 and DN25 ½" ½"
The cap can be drilled to the following
sizes to enable a blowdown or drain DN32 and DN40 1" ¾"
valve to be fitted.
DN50 to DN125 1¼" ¾"

DN150 and DN200 2" ¾"

TI-P160-02 Page 1 of 4
CMGT Issue 13
Fig 36 Austenitic Stainless Steel Strainer
 Materials
No. Part Size Material

Austenitic stainless steel

1 Body
ASTM A351 CF3M

Austenitic stainless steel

DN15 - DN50
ASTM A351 CF3M
2 Cap
Austenitic stainless steel
DN65 - DN200
ASTM A351 CF3M

Reinforced exfoliated
3 Cap gasket
graphite 1
4
Austenitic stainless steel
4 Strainer screen
ASTM A240 316L 3
Austenitic stainless steel
5 Cap bolt 2
ISO 3506 A2-70
5

Pressure/temperature limits
A
The product must not be used in this region.
Temperature °C

A - B Flanged ANSI 300.

Steam A - C Flanged EN 1092 PN40.
saturation
D curve
C B

Pressure bar g

Body design conditions ANSI 300 (PN50)

PMA Maximum allowable pressure 41 bar g @ 38 °C

TMA Maximum allowable temperature 450 °C @ 21 bar g

Minimum allowable temperature -29 °C

ANSI 150 16 bar g

PMO Maximum operating pressure PN40 38 bar g

ANSI 300 41 bar g

TMO Maximum operating temperature 450 °C @ 21 bar g

Minimum operating temperature

-29 °C
Note: For lower operating temperatures consult Spirax Sarco.

Designed for a maximum cold hydraulic test pressure of: 76 bar g

Kv values
Size DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 DN125 DN150 DN200

Perforations 0.8, 1.6 and 3 mm 5 8 13 22 29 46 72 103 155 237 340 588

Mesh 40 and 100 5 8 13 22 29 46 72 103 155 237 340 588

Mesh 200 4 6 10 17 23 37 58 83 124 186 268 464

For conversion:
Cv (UK) = Kv x 0.963
Cv (US) = Kv x 1.156

Page 2 of 4 TI-P160-02
CMGT Issue 13
Fig 36 Austenitic Stainless Steel Strainer
Dimensions/weights (approximate) in mm and kg
EN1092
PN16/25/40 ANSI 150 ANSI 300 Screening area
Size A A A B C cm² Weight

DN15 130 124 130 70 120 28 2.5

DN20 150 142 149 80 130 46 4.5

DN25 160 156 163 95 162 79 5.0

DN32 180 180 180 130 235 135 10.0

DN40 200 200 208 146 260 161 12.0

DN50 230 230 241 180 320 251 16.5

DN65 290 290 290 200 325 325 23.0

DN80 310 310 310 205 330 360 35.6

DN100 351 351 351 255 405 540 38.5

DN125 400 400 400 315 510 840 76.0

DN150 480 475 480 345 560 1 115 109.0

DN200 600 594 600 440 710 1 905 144.0

B C

Withdrawal distance

Safety information, installation and maintenance

For full details see the Installation and Maintenance Instructions (IM-S60-18) supplied with the product.

Installation note:
The strainer should be installed in the direction of flow, as indicated on the body. On applications involving steam or gases the pocket
should be in the horizontal plane. On liquid systems the pocket should point downwards. Suitable isolation valves must be installed to
allow for safe maintenance and trap replacement.

Maintenance note:
Maintenance can be completed with the strainer in the pipeline, once the safety procedures have been observed. It is recommended
that a new gasket is used whenever maintenance is undertaken.

Warning:
The strainer cap gasket contains a thin stainless steel support ring, which may cause physical injury if it is not handled and disposed
of carefully.

Disposal
The product is recyclable. No ecological hazard is anticipated with disposal of this product, providing due care is taken.

How to order
Example: 1 off Spirax Sarco DN32 Fig 36 strainer having a stainless steel screen with 0.8 mm perforations. The connections are to
be flanged EN 1092 PN40.

TI-P160-02 Page 3 of 4
CMGT Issue 13
Fig 36 Austenitic Stainless Steel Strainer
Spare parts
The spare parts available are shown in solid outline. Parts drawn in a grey line are not supplied as spares.

Available spares
Strainer screen (state material, size of perforations or mesh and size of strainer) 4

Cap gasket (3 off) 3

How to order spares

Always order spares by using the description given in the column headed 'Available spares' and state the size and type of strainer and
perforation or mesh required.
Example: 1 off stainless steel strainer screen, having 0.8 mm perforations for a DN50 Spirax Sarco Fig 36 strainer having EN 1092
PN40 connections.

Recommended tightening torques

or
Item Size Qty Nm
mm

DN15 - DN25 4 16 A/F M10 x 30 22 - 25

4
DN32 - DN40 4 19 A/F M12 x 35 40 - 45
3
DN50 8 19 A/F M12 x 35 40 - 45

DN65 8 19 A/F M12 x 45 40 - 45

5 DN80 8 19 A/F M12 x 50 40 - 45

DN100 8 24 A/F M16 x 50 100 - 110

DN125 8 30 A/F M20 x 60 160 - 170

DN150 8 30 A/F M20 x 65 210 - 230

DN200 8 36 A/F M20 x 75 210 - 230 5

Page 4 of 4 TI-P160-02
CMGT Issue 13
Fig 36 Austenitic Stainless Steel Strainer