VENPER ACADEMY Total Marks: 60

Total Time: 30 Minutes

Units and Dimensions

Instructions :
1. Check the test duration and number of questions on the question paper carefully. For each correct response, the candidate
will get 4 marks. For each incorrect response, one mark will be deducted from the total scores.

2. Please ensure you have got all the pages of the paper clearly printed.

3. Use Blue / Black Ball Point Pen only for writing particulars or filling circles in the OMR sheet. Fill the circles fully, without

4
spillover.

4. The candidates should ensure that the Answer Sheet (OMR Sheet) is not folded. Do not make any stray marks on the

2
Answer Sheet.

5. Maintain silence while attempting the paper.

0
6. Use of Electronic/Manual Calculator, or any other Electrionic Gadget like Mobile is strictly prohibited.

2
7. Do not waste unnecessary time if you get stuck up in any question. Leave that question to be visited again later. First
attempt the questions you may do easily. Remember, your goal is to maximize your marks!

-
1. The unit of power is 5
(A) Joule (D)
2

R
(B) Joule per second only
b c
(C) Joule per second and watt both 6. A physical quantity is given by X =M aL T . The
(D) Only watt percentage error in measurement of M, L and T are α

A
, β and γ respectively. Then maximum percentage
2. Which of the following is not a unit of energy error in the quantity X is
(A) W-s (A) aα+bβ+cγ

E
(B) kg-m/sec (B) aα+bβ−cγ
(C) N-m a b c

Y
(C) + +
(D) Joule α β γ
3. The dimensions of power are (D) None of these
1 2 −3
(A) M L T 2
7. In S = a +bt+ct . S is measured in metres and t in
2 1 −2 seconds. The unit of c is
(B) M L T
1 2 −1 (A) None
(C) M L T
(B) m
1 1 −2
(D) M L T
(C) ms−1
4. The dimensional formula for impulse is same as the (D) ms−2
dimensional formula for
(A) Momentum 8. Wavelength of ray of light is 0.00006 m . It is equal to
(in microns)
(B) Force
(A) 6
(C) Rate of change of momentum
(B) 60
(D) Torque
(C) 600
V (D) 0.6
5. The resistance R = where V= 100 ± 5 volts and i
i 9. Which of the following is dimensionally correct
= 10 ± 0.2 amperes. What is the total error in R (in
(A) Pressure = Energy per unit area
percentage)
(B) Pressure = Energy per unit volume
(A) 5
(C) Pressure = Force per unit volume
(B) 7
(D)
(C) 5.2
Pressure = Momentum per unit volume per unit time

Page 1 of 2 VENPER ACADEMY

 1 (B) 8
3 2
A B (C) 5
10. A physical quantity P is given by P = 3
. The
(D) 1
C −4D 2

quantity which brings in the maximum percentage 13. Unit of impulse is

error in P is (A) Newton
(A) A (B) kg-m
(B) B (C) kg-m/s
(C) C (D) Joule
(D) D
14. In a new system of units, unit of mass is 10 kg, unit of

4
11. When a wave travels in a medium, the displacement of length is 100m, unit of time is 1 minutes. Then
a particle located at distance x at time t is given by y magnitude of 1 N force in new system of units will be

2
= a sin (bt – cx) where a, b and c are constants of the (A) 36
wave. The dimension of b/c are same as that of :
(B) 60
(A) wave velocity

0
(C) 3.6
(B) wave length
(D) 0.06
(C) wave amplitude

2
(D) wave frequency 15. The dimensional formula of wave number is
(A) M°L°T–1
12. The percentage errors in the measurement of mass

-
and speed are 2% and 3% respectively. How much will (B) M–1L–1T°
be the maximum error in the estimate of kinetic (C) M°L–1T°
energy obtained by measuring mass and speed ? (in
(D) M°L°T°
percentage)

R
(A) 0.11

E A
Y

Page 2 of 2 VENPER ACADEMY