Scribd
Upload
8 views

RCC14 Crack Width

The document provides detailed crack width calculations for concrete structures according to BS8110 and BS8007 standards, including input parameters such as material properties and reinforcement details. It outlines the calculations for various parameters like moduli of elasticity, neutral axis depth, and calculated crack width, resulting in a final crack width of 0.19 mm. Additionally, it includes a disclaimer about the use of the spreadsheet and its shareware status, along with a revision history of the software.

Uploaded by

starlinkjupitor
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
8 views

RCC14 Crack Width

The document provides detailed crack width calculations for concrete structures according to BS8110 and BS8007 standards, including input parameters such as material properties and reinforcement details. It outlines the calculations for various parameters like moduli of elasticity, neutral axis depth, and calculated crack width, resulting in a final crack width of 0.19 mm. Additionally, it includes a disclaimer about the use of the spreadsheet and its shareware status, along with a revision history of the software.

Uploaded by

starlinkjupitor
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 2

Project

Spreadsheets to BS 8110etc The Concrete Centre


Client Advisory Group Made by Date Page
Location Grid line 1 RC 02-Mar-2025 34
Crack Width Calculations to BS8110: 2005/ BS8007:1987 Checked Revision Job No
Originated from RCC14.xls v 4.0on CD © 2006 TCC chg - R68

CRACK WIDTH CALCULATIONS - FLEXURE -

INPUT
fcu= 35 N/mm2
fy= 500 N/mm2
Area of reinforcement " As " = 2093 mm2
b= 1000 mm
h= 250 mm
d= 200 mm
Minimum cover to tension reinforcement " CO " = 40 mm
Maxmum bar spacing " S " = 150 mm
Bar dia " DIA " = 20 mm
" acr " =(((S/2)^2+(CO+DIA/2)^2)^(1/2)-DIA/2) as default or enter other value = 80.14 mm
"acr " is distance from the point considered to the surface of the nearest longitudinal bar
Applied service moment " Ms "= 69.0 KNm

CALCULATIONS
moduli of elasticity of concrete " Ec" = (1/2)*(20+0.2*fcu) = 13.5 KN/mm2
moduli of elasticity of steel " Es " = 200.0 KN/mm2
Modular ratio " a " = (Es/Ec) = 14.81
" r " = As/bd = 0.010
depth to neutral axis, "x" = (-a.r +((a.r)2 + 2.a.r)0.5.d = 85 mm

" Z " = d-(x/3) = 172


Reinforcement stress " fs " = Ms/(As*Z) = 192 N/mm2
Concrete stress " fc " = (fs*As)/(0.5*b*x) = 9.50 N/mm2
Strain at soffit of concrete beam/slab " e1 " = (fs/Es)*(h-x)/(d-x) = 0.001375
Strain due to stiffening effect of concrete between cracks " e2 " =
e2 = b.(h-x)2/(3.Es.As.(d-x)) for crack widths of 0.2 mm Used
e2 = 1.5.b.(h-x) /(3.Es.As.(d-x)) for crack widths of 0.1 mm
2
n/a
e2 = 0.000189
Average strain for calculation of crack width " em "= e1-e2 = 0.001186

Calculated crack width, " w " = 3.acr.em/(1+2.(acr-c)/(h-x))


CALCULATED CRACK WIDTH, 'w' = 0.19 mm
Disclaimer
All advice or information from MPA-The Concrete Centre is intended for those who will evaluate the significance and limitations of its
contents and take responsibility for its use and application. No liability (including that for negligence) for any loss resulting from such advice
or information is accepted by MPA-The Concrete Centre or its subcontractors, suppliers or advisors. Users should note that all MPA-The
Concrete Centre software and publications are subject to revision from time to time and they should therefore ensure that they are in
possession of the latest version.
This spreadsheet should be used in compliance with the accompanying publication 'User Guide RC Spreadsheets: v4' available from The
Concrete Centre www.concretecentre.com/rcdesign Tel +44 (0)1276 606800

Status of spreadsheet This spreadsheet is shareware but may not be used for commercial purposes until the
user has registered with The Concrete Centre using the licence validation form available
Public release version. on The Concrete Centre website www.concretecentre.com/rcdesign

Revision history RCC14 Crack Width.xls

Date Version Action Size (kB)


30-Mar-10 RCC14 v4.0 Re-badged as TCC/Mineral Products Association. 226
17-Sep-09 RCC14 v3.2 Steel stress limit set to 0.8fy. 192
28-Jun-06 RCC14 v3.1 v3 release. Page nos, User Guide and registration details amended. 152
21-Oct-05 RCC14 v3.0 Updated to 2005 version of BS8110 177
21-Jan-03 RCC14 v2.1 DETR logo replaced by DTI. 156
11-Oct-02 RCC14 v2.0 Version 2 enhancements 172
4-Aug-99 RCC14 v1.1 Renamed 81

You might also like