Technical Education and Skills Development Authority

COMPETENCY-BASED CURRICULUM

Construction Sector

System Formwork Installation

NC II

Qualifications and Standards Office

TESDA Complex
East Service Road, South Superhighway
Taguig City, Metro Manila
Tel. No. (02) 893-8281, 8938303
www.tesda.gov.ph
 TABLE OF CONTENTS
Page

A. Course Design 1-5

B. Modules of Instruction 6-65

● BASIC COMPETENCIES
o Participate in workplace communication 7-10
o Work in a team environment 11-13
o Practice career professionalism 14-17
o Practice occupational health and safety 18-22

● COMMON COMPETENCIES
o Preparing construction materials and tools 24-27
o Performing mensuration and calculation 28-30
o Maintaining tools and equipment. 31-34
o Observing procedures, specifications and manuals of
instructions 35-38
o Interpreting technical drawings and plans 39-41

● CORE COMPETENCIES
o Assembling and dismantling scaffolding/shoring and braces
43-47
o Installing system formwork 48-55
o Stripping system formwork 56-60

COURSE DESIGN

COURSE TITLE : SYSTEM FORMWORK INSTALLATION NC II

TRAINING DURATION : 156 Hours

COURSE DESCRIPTION :

This course is designed to enhance the knowledge, skills, positive attitude and work
values of a student/learner on competencies such as, participate in workplace
 communication, work in a team environment, practice career professionalism, and
practice occupational health and safety, prepare construction materials and tools, perform
mensuration, maintain tools and equipment, observe procedures specifications and
manuals of instructions, and interpret technical drawings and plans.

This cover the special competencies to enable a person to perform assembling and
dismantling of shoring/scaffolding, installation and stripping of system formwork
utilizing various types of materials, and technologies in constructing various structures
in a diverse construction work environment.

ENTRY REQUIREMENTS :
Candidate/trainee must reach/poses any of the following qualification:
● Ability to communicate
● Physically fit and mentally healthy
● Can perform basic mathematical computation and mensuration.

COURSE STRUCTURE:

BASIC COMPETENCIES
(18 hours)

UNIT OF TRAINING
MODULE TITLE LEARNING OUTCOMES
COMPETENCY DURATION
1. Participate in 1.1 Participating in 1.1.1 Obtain and convey 4 hours
workplace workplace workplace information
communication communication 1.1.2 Complete relevant work
related documents.
1.1.3 Participate in workplace
meeting and discussion.
2. Work in a team 2.1 Working in a 2.1.1 Describe and identify 4 hours
environment team team role and
environment responsibility in a team.
2.1.2 Describe work as a team.
3. Practice career 3.1 Practicing career 3.1.1 Integrate personal 6 hours
professionalism professionalism objectives with
organizational goals
3.1.2 Set and meet work
priorities
3.1.3 Maintain professional
growth and development
4. Practice 4.1 Practicing 4.1.1 Identity hazards and 4 hours
occupational occupational risks
health and health and 4.1.2 Evaluate hazards and
safety safety risks
4.1.3 Control hazards and risks
4.1.4 Maintain occupational
health and safety
awareness
 COMMON COMPETENCIES
(18 hours)

UNIT OF TRAINING
MODULE TITLE LEARNING OUTCOMES
COMPETENCY DURATION
1. Prepare 1.1 Preparing 1.1.1 Identify materials and 4 hours
construction construction tools applicable to a
materials and (heavy specific construction job.
tools equipment) 1.1.2 Request appropriate
materials and materials and tools.
tools.
1.1.3 Receive and inspect
materials.
2. Perform 2.1 Performing 2.1.1 Carry out 4 hours
mensuration mensuration measurements and
and calculation and calculations calculations.
2.1.2 Select measuring
instruments.
3. Maintain tools 3.1 Maintaining 3.1.1 Check condition of tools 3 hours
and equipment. tools and and equipments.
equipment. 3.1.2 Perform basic
preventive maintenance
3.1.3 Store tools and equipment
4. Observe 4.1 Observing 4.1.1 Identify, access, and 4 hours
procedures, procedures, interpret specification/
specifications specifications manuals.
and manuals and manuals of 4.1.2 Apply information in
of instructions instructions. manual
4.1.3 Store manuals.
5. Interpret 5.1 Interpreting 5.1.1 Analyze signs, symbols 3 hours
technical technical and data.
drawings and drawings and 5.1.2 Interpret technical
plans plans drawings and plans
 CORE COMPETENCIES
(80 hours)
(Plus 40 hours OJT)

UNIT OF TRAINING
MODULE TITLE LEARNING OUTCOMES
COMPETENCY DURATION
1. Assemble and 1.1 Assembling 1.1.1 Plan and prepare for 32 hours
dismantle and operation
scaffold/ dismantling 1.1.2 Erect shoring/scaffold
shoring and scaffolding/ 1.1.3 Inspect replace
braces shoring and defective shoring/
braces scaffolding components
1.1.4 Dismantle shoring/
scaffolding and clean up

2. Install 2.1 Installing 2.1.1 Prepare materials, 32 hours

formwork formwork tools and equipment for
components components installing formworks
2.1.2 Assemble scaffolds/
shoring and braces
2.1.3 Set/fix form system of
structure components

3. Strip 3.1 Stripping 3.1.1 Prepare staging area, 16 hours

formwork formwork t
components components o
o
l
s

a
n
d

e
q
u
i
p
m
e
n
t
3.1.2 Strip formworks of
b
u
il
d
i
n
g
RESOURCES:

Tools Equipment Materials

● Hammer ● Compressor ● Sheathing (metal,
laminated plastic)
assembly
● Spirit level ● Saw (hand, circular) ● Shoring and
accessories
● Pull-push pen ● Personal protective ● Scaffolds and
Equipment (Gloves, Safety accessories
● Plumb bob shoes, ● Pencil
Hard hat, Safety harness,
Safety goggles)
● Steel square ● Audi video equipment ● Lumber plywood
● Tri-square ● Power drill ● Nails
● Meter tape ● Portable grinder ● Form ties/ walers
● Level hose ● Lifting equipment ● Form oil
● Wrenches / ● Reference books,
spanners
● Chisels ● Modules, hands out,
multimedia materials.

TRAINING DELIVERIES:

● School-based training
● Center-based training
● Industry-based training
● Dual –Training systems
●

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Direct Observation
● Demonstration of Practical Skills

TRAINER’S QUALIFICATIONS:

● Must have undergone training on Training Methodology I (TM I)

● Must be a holder of Metal Formworks Installation Certificate Level II
● Must be computer literate
● Must be physically and mentally fit
● *Must have 1 year industry experience and/or teaching experience
 MODULES OF INSTRUCTION

BASIC COMPETENCIES

SYSTEM FORMWORK INSTALLATION NC II

UNIT OF COMPETENCY : PARTICIPATE IN WORKPLACE COMMUNICATION

MODULE TITLE : PARTICIPATING IN WORKPLACE COMMUNICATION

MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes required to
obtain, interpret and convey information in response to
workplace requirements.

TRAINING DURATION : 4 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module the students/ trainees will be able to:

LO1. Obtain and convey workplace information

LO2. Complete relevant work related documents.

LO3. Participate in workplace meeting and discussion.

LO1. OBTAIN AND CONVEY WORKPLACE INFORMATION

ASSESSMENT CRITERIA:

1. Specific relevant information is accessed from appropriate sources.

2. Effective questioning, active listening and speaking skills are used to gather
and convey information.
3. Appropriate medium is used to transfer information and ideas.
4. Appropriate non-verbal communication is used.
5. Appropriate lines of communication with superiors and colleagues are
identified and followed.
6. Defined workplace procedures for the location and storage of information
are used.
7. Personal interaction is carried out clearly and concisely.

CONTENTS:

● Parts of speech
● Sentence construction
● Effective communication

CONDITIONS:

The students/ trainees must be provided with the following:

● Writing materials (pen & paper)

● References (books)
● Manuals

METHODOLOGIES:

● Group discussion
● Interaction
● Lecture
● Reportorial

ASSESSMENT METHODS:

● Written test
● Practical/performance test
● Interview
L02. COMPLETE RELEVANT WORK RELATED DOCUMENTS

ASSESSMENT CRTERIA:

1. Ranges of forms relating to conditions of employment are completed

accurately and legibly.
2. Workplace data is recorded on standard workplace forms and documents.
3. Basic mathematical process is used for routine calculations.
4. Errors in recording information on forms/ documents are identified and
rectified.
5. Reporting requirements to superior are completed according to enterprise
guidelines.

CONTENTS:

● Basic mathematics
● Technical writing
● Types of forms

CONDITIONS:

The students/trainees must be provided with the following:

● Paper
● pencils/ball pen
● Reference books
● Manuals

METHODOLOGIES:

● Group discussion
● Interaction
● Lecture

ASSESSMENT METHODS:

● Written test
● Practical/performance test
● Interview
LO3. PARTICIPATE IN WORKPLACE MEETINGS AND DISCUSSIONS

ASSESSMENT CRITERIA:

1. Team meetings are attended on time.

2. Own opinions are clearly expressed and those of others are listened to
without interruption.
3. Meeting inputs are consistent with the meeting purpose and established
protocols.
4. Workplace interaction is conducted in a courteous manner appropriate to
cultural background and authority in the enterprise procedures.
5. Questions about simple routine workplace procedures and matters
concerning conditions of employment are asked and responded.
6. Meeting outcomes are interpreted and implemented.

CONTENTS:

● Sentence construction
● Technical writing
● Recording information

CONDITIONS:

The students/trainees must be provided with the following:

● Paper
● Pencils/ball pen
● References (books)
● Manuals

METHODOLOGIES:

● Group discussions
● Interaction
● Lecture

ASSESSMENT METHODS:

● Written test
● Practical/performance test
● Interview
UNIT OF COMPETENCY : WORK IN A TEAM ENVIRONMENT

MODULE TITLE : WORKING IN A TEAM ENVIRONMENT

MODULE DESCRIPTOR : This module covers the knowledge, skills, and attitudes required to
relate in a work based environment.

TRAINING DURATION : 4 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the students/ trainees will be able to:

LO1. Describe and identify team role and responsibility in a team.

LO2. Describe work as a team.

LO1. DESCRIBE AND IDENTIFY TEAM ROLE AND RESPONSIBILITY IN A TEAM

ASSESSMENT CRITERIA:

1. Role and objective of the team is identified.

2. Team parameters, relationships and responsibilities are identified.
3. Individual role and responsibilities within team environment are identified.
4. Roles and responsibilities of other team members are identified and
recognized.
5. Reporting relationships within team and external to team are identified.

CONTENTS:

● Team role.
● Relationship and responsibilities
● Role and responsibilities with team environment.
● Relationship within a team.

CONDITIONS:

The students/ trainees must be provided with the following:

● Standard operating procedure (SOP) of workplace

● Job procedures
● Client/supplier instructions
● Quality standards
● Organizational or external personnel

METHODOLOGIES:

● Group discussion/interaction
● Case studies
● Simulation

ASSESSMENT METHODS:

● Written test
● Observation
● Simulation
● Role playing
LO2. DESCRIBE WORK AS A TEAM MEMBER

ASSESSMENT CRITERIA:

1. Appropriate forms of communication and interactions are undertaken.

2. Appropriate contributions to complement team activities and objectives
were made.
3. Reporting using standard operating procedures followed.
4. Development of teamwork plans based from role team were contributed

CONTENTS:

● Communication process
● Team structure/team roles
● Group planning and decision-making

CONDITIONS:

The students/trainees must be provided with the following:

● SOP of workplace
● Job procedures
● Organization or external personnel

METHODOLOGIES:

● Group discussion/interaction
● Case studies
● Simulation

ASSESSMENT METHODS:

● Observation of work activities

● Observation through simulation or role-play
● Case studies and scenarios.
UNIT OF COMPETENCY : PRACTICE CAREER PROFESSIONALISM

MODULE TITLE : PRACTICING CAREER PROFESSIONALISM

MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes in
promoting career growth and advancement, specifically; to
integrate personal objectives with organizational goals set
and meet work priorities and maintain professional growth
and development.

TRAINING DURATION : 6 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainee/student must be able to:

LO1. Integrate personal objectives with organizational goals

LO2. Set and meet work priorities

LO3. Maintain professional growth and development

LO1. INTEGRATE PERSONAL OBJECTIVES WITH ORGANIZATIONAL GOALS

ASSESSMENT CRITERIA:

1. Personal growth and work plans towards improving the qualifications set
for professionalism are evident.
2. Intra and interpersonal relationship in the course of managing oneself
based on performance evaluation is maintained.
3. Commitment to the organization and its goal is demonstrated in the
performance of duties.
4. Practice of appropriate personal hygiene is observed.
5. Job targets within key result areas are attained.

CONTENTS:

● Personal development-social aspects: intra and interpersonal development

● Organizational goals
● Personal hygiene and practices
● Code of ethics

CONDITIONS:

The students/ trainees must be provided with the following:

● Workplace
● Code of ethics
● Organizational goals
● Handouts and Personal development-social aspects
● CD’s, VHS tapes, transparencies

METHODOLOGIES:

● Interactive -lecture
● Simulation
● Demonstration
● Self paced instruction

ASSESSMENT METHODS:

● Role play
● Interview
● Written examination
LO2. SET AND MEET WORK PRIORITIES

ASSESSMENT CRITERIA:

1. Competing demands to achieve personal, team and organizational goals

and objectives are prioritized.
2. Resources are utilized efficiently and effectively to manage work priorities
and commitments.
3. Practices and economic use and maintenance of equipment and facilities
are followed as per established procedures.
4. Job targets within key result areas are attained.

CONTENTS:

● Organizational key result areas (KRA)

● Work values and ethical standards
● Company policies on the use and maintenance of equipment

CONDITIONS:

The students/ trainees must be provided with the following

● Hand outs on
● Organizational KRA
● Work values and ethics
● Company policies and standards
● Sample job targets
● Learning guides
● CD’s, VHS tapes, transparencies

METHODOLOGIES:

● Interactive lecture
● Group discussion
● Structured activity
● Demonstration

ASSESSMENT METHODS:

● Role play
● Interview
● Written examination
LO3. MAINTAIN PROFESSIONAL GROWTH AND DEVELOPMENT

ASSESSMENT CRITERIA:

1. Training and career opportunities relevant to the job requirements are

identified and availed.
2. Licenses and/or certifications according to the requirements of the
qualifications are acquired and maintained
3. Fundamental rights at work including gender sensitivity are manifested/
observed
4. Training and career opportunities based on the requirements of industry are
completed and updated.

CONTENTS:

● Qualification standards
● Gender and development (GAD) sensitivity
● Professionalism in the workplace
● List of professional licenses

CONDITIONS:

The students/trainees must be provided with the following

● Quality standards
● GAD handouts
● CD’s, VHS tapes on professionalism in the workplace
● Professional licenses samples

METHODOLOGIES:

● Interactive lecture
● Film viewing
● Role play/simulation
● Group discussion

ASSESSMENT METHODS:

● Demonstration
● Interview
● Written examination
UNIT OF COMPETENCY : PRACTICE OCCUPATIONAL HEALTH AND SAFETY PROCEDURES

MODULE TITLE : PRACTICING OCCUPATIONAL HEALTH AND SAFETY PROCEDURES

MODULE DESCRIPTOR : This module covers the knowledge, skills and attitudes required to
comply with the regulatory and organizational requirements
for occupational health and safety such as identifying,
evaluating and maintaining occupational health and safety
(OHS) awareness.

TRAINING DURATION : 4 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainee/student must be able to:

LO1. Identity hazards and risks

LO2. Evaluate hazards and risks

LO3. Control hazards and risks

LO4. Maintain occupational health and safety awareness

LO1. IDENTIFY HAZARDS AND RISKS

ASSESSMENT CRITERIA:

1. Workplace hazards and risks are identified and clearly explained.

2. Hazards/risks and its corresponding indicators are identified in with the
company procedures.
3. Contingency measures are recognized and established in accordance with
organizational procedures.

CONTENTS:

● Hazards and risks identification and control

● Organizational safety and health protocol
● Threshold limit value (TLV)
● OHS indicators

CONDITIONS:

The students/ trainees must be provided with the following:

● Workplace
● Personal protective equipment (PPE)
● Learning guides
● Hand-outs
● Organizational safety and health protocol
● OHS indicators
● Threshold limit value
● Hazards/risk identification and control
● CD’s, VHS tapes, transparencies

METHODOLOGIES:

● Interactive lecture
● Simulation
● Symposium
● Group dynamics

ASSESSMENT METHODS:

● Situation analysis
● Interview
● Practical examination
● Written examination
LO2. EVALUATE HAZARDS AND RISKS

ASSESSMENT CRITERIA:

1. Terms of maximum tolerable limits are identified based on threshold limit

values (TLV)
2. Effects of hazards are determined.
3. OHS issues and concerns are identified in accordance with workplace
requirements and relevant workplace OHS legislation.

CONTENTS:

● TLV table
● Philippine OHS standards
● Effects of hazards in the workplace
● Ergonomics
● ECC Regulations

CONDITIONS:

The students/trainees must be provided with the following

● Hand outs on
● Philippine OHS standards
● Effects of hazards in the workplace
● Ergonomics
● ECC regulations
● TLV table
● CD’s, VHS tapes, transparencies

METHODOLOGIES:

● Interactive lecture
● Situation analysis
● Symposium
● Film viewing
● Group dynamics

ASSESSMENT METHODS:

● Interview
● Written examination
● Simulation
LO3. CONTROL HAZARDS AND RISKS

ASSESSMENT CRITERIA:

1. OHS procedures for controlling hazards and risk are strictly followed.
2. Procedures in dealing with workplace accidents, fire and emergencies are
followed in accordance with the organization’s OHS policies.
3. Personal protective equipment (PPE) is correctly used in accordance with
organization’s OHS procedures and practices.
4. Procedures in providing appropriate assistance in the event of workplace
emergencies are identified in line with the established organizational protocol.

CONTENTS

● Safety regulations
● Clean air act
● Electrical and fire safety code
● Waste management
● Disaster preparedness and management
● Contingency measures and procedures

CONDITIONS:

The students/trainees must be provided with the following:

● Hand outs on
● Safety regulations
● Clean air act
● Electrical and fire safety code
● Waste management
● Disaster preparedness and management
● Contingency measures and procedures
● OHS personal records
● PPE
● CD’s, VHS tapes, transparencies

METHODOLOGIES:

● Interactive lecture
● Symposium
● Film viewing
● Group dynamics
● Self-paced instruction

ASSESSMENT METHODS:

● Written examination
● Interview
LO4. MAINTAIN OCCUPATIONAL HEALTH AND SAFETY AWARENESS

ASSESSMENT CRITERIA:

1. Procedures in emergency related drill are strictly followed in line with the
established organization guidelines and procedures.
2. OHS personal records are filled up in accordance with workplace
requirements.
3. PPE are maintained in line with organization guidelines and procedures.

CONTENTS:

● Operational health and safety procedure, practices and regulations

● Emergency-related drills and training

CONDITIONS:

The students/trainees must be provided with the following

● Workplace
● PPE
● OHS personal records
● CD’s, VHS tapes, transparencies
● Health record

METHODOLOGIES:

● Interactive lecture
● Simulation
● Symposium
● Film viewing
● Group dynamics

ASSESSMENT METHODS:

● Demonstration
● Interview
● Written examination

MODULES OF INSTRUCTION

COMMON COMPETENCIES

SYSTEM FORMWORK INSTALLATION NC II

UNIT OF COMPETENCY : PREPARE CONSTRUCTION MATERIALS AND TOOLS
MODULE TITLE : PREPARING CONSTRUCTION (SYSTEM FORMWORK) MATERIALS AND
TOOLS

TRAINING DURATION : 4 hours

MODULE DESCRIPTION : This module covers the knowledge, skills and attitudes on
identifying, requesting and receiving construction materials
and tools based on the required performance standards.

SUMMARY OF LEARNING OUTCOMES:

Upon completion of the module the trainees/student should be able to:

LO1. Identify materials and tools applicable to a specific construction job

LO2. Request appropriate materials and tools

LO3. Receive and inspect materials

LO1. IDENTIFY MATERIALS AND TOOLS APPLICABLE TO A SPECIFIC JOB

ASSESSMENT CRITERIA:

1. Tools and materials are identified as per job requirements

2. Tools are classified according to its function as per job requirements.
3. Materials are classified according to its uses to a specific construction
project.
4. Tools and materials are selected as per job requirement.

CONTENTS:

● Types and uses of construction materials and tools

● Description of materials and tools
● Listing of materials as per company standards.

CONDITIONS:

Students/trainees must be provided with the following:

● Workplace location
● Materials relevant to the unit of competency
● Materials and tools
● Materials and tools different brand names, size, capacity and kind of
application.
● Handouts/Instructional Materials

METHODOLOGIES:

● Lecture-demonstration
● Self-paced instruction
● Group discussion
● PowerPoint presentation

ASSESSMENT METHODS:

● Direct observation
● Written test/ questioning
LO2.REQUEST APPROPRIATE MATERIALS AND TOOLS

ASSESSMENT CRITERIA:

1. Needed materials and tools listed as per job requirement.

2. Materials and tools are requested according to the list prepared.
3. Requests are done as per company’s standard operating procedures (SOP)
4. Materials and tools are substituted and provided unavailable without
sacrificing cost and quality of work.

CONTENTS:

● Different forms
● Job order slip
● Tools and materials requisition slip
● Borrower’s slip
● Requisition procedures

CONDITIONS:

Students/trainees must be provided with the following:

● Sample of company standard in tools and materials requisition.

● Job order form
● Requisition slip
● Borrowers slip
● Handouts/Instructional materials

METHODOLOGIES:

● Lecture-demonstration
● Self-paced instruction
● Group discussion

ASSESSMENT METHODS:

● Oral questioning
● Direct observation
● Written test
LO3. RECEIVE AND INSPECT MATERIALS

ASSESSMENT CRITERIA:

1. Received and inspected materials and tools as per quantity and

specification based on requisition.
2. Tools and materials are checked for damages and manufacturing defects.
3. Materials and tools received are handled with appropriate safety devices.
4. Materials and tools are set aside to appropriate location nearest to the
workplace.

CONTENTS:

● Procedures in receiving tools and materials

● Proper inspection of tools and materials received.
● Proper handling of tools and materials.

CONDITIONS:

Students/trainees must be provided with the following:

● Sample of company standard in tools and materials in receiving materials.

● Inspection checklist
● Materials handling safety devices
● Inventory form handouts/instructional materials

METHODOLOGIES:

● Lecture-demonstration
● Self-paced instruction
● Group discussion

ASSESSMENT METHODS:

● Oral questioning
● Direct observation
● Written test
UNIT OF COMPETENCY : PERFORM MENSURATIONS AND CALCULATIONS

MODULE TITLE : PERFORMING MENSURATIONS AND CALCULATIONS

TRAINING DURATION : 4 hours

MODULE DESCRIPTION : This module covers the knowledge, skills and attitudes on
identifying, and measuring objects based on the required
performance standards.

SUMMARY OF LEARNING OUTCOMES:

Upon completion of the module the trainees/student should be able to:

LO1. Carry out measurements and calculations.

LO2. Select measuring instruments.

LO1. CARRY OUT MEASUREMENTS AND CALCULATIONS

ASSESSMENT CRITERIA:

1. Calculation needed to complete work tasks are performed using the four
basic process of addition (+), subtraction (-), multiplication (x) and division (/)
including but not limited to: trigonometric functions, algebraic computations.
2. Calculations involving fractions, percentages and mixed numbers are used
to complete workplace tasks
3. Numerical computations are self-checked and corrected for accuracy.
4. Accurate measurements are obtained according to job requirements.
5. Identified and converted systems of measurement according to job
requirements.
6. Measured work pieces according to job requirements.

CONTENTS:

● Trade mathematics/mensuration
● Four fundamental operation
● Kinds of measurement
● Dimensions
● Ratio and proportion
● Trigonometric functions
● Algebraic equations
● Fractions, percentage and decimals
● Conversion

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Workplace location
● Problems to solve
● Measuring instruments
● Instructional materials relevant to the propose activity.

METHODOLOGIES:

● Lecture-demonstration
● Self-paced instruction
● Group discussion

ASSESSMENT METHODS:

● Oral questioning
● Direct observation
● Written test
LO2. SELECT MEASURING INSTRUMENTS

ASSESSMENT CRITERIA

1.Object or component to be measured are identified, classified and interpreted

according to the appropriate regular geometric shape.
2.Measuring tools are selected/identified as per object to be measured or job
requirements
3.Correct specifications are obtained from relevant sources.
4.Measuring instruments are selected according to job requirements.
5.Alternative measuring tools are used without sacrificing cost and quality of
work.
6.Measurements are obtained according to job requirements.

CONTENTS

● Visualizing objects and shapes specifically geometric shapes.

● Interpreting Formulas for volume, areas, and perimeters of plane and geometric
figures.
● Measuring Instruments/Measuring Tools
● Proper handling of measuring instruments

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Workplace Location
● Problems to solve
● Measuring instruments
● Instructional materials relevant to the propose activity.

METHODOLOGIES:

● Actual demonstration
● Classroom discussions

ASSESSMENT METHODS:

● Actual demonstration
● Direct observation
● Written test/questioning
UNIT OF COMPETENCY : MAINTAIN TOOLS AND EQUIPMENT

MODULE TITLE : MAINTAINING TOOLS AND EQUIPMENT

TRAINING DURATION : 3 hours

MODULE DESCRIPTION : This module covers the knowledge, skills and attitudes on
checking condition, performing preventive maintenance and
storing of tools and equipment based on the required
performance standard.

SUMMARY OF LEARNING OUTCOMES:

Upon completion of the module the trainees/student should be able to:

LO1. Check condition of tools and equipments

LO2. Perform basic preventive maintenance

LO3. Store tools and equipment

LO1. CHECK CONDITIONS OF TOOLS AND EQUIPMENTS

ASSESSMENT CRITERIA:

1. Tools and equipment are identified according to classification/specification

and job requirements.
2. Non-functional tools and equipment are segregated and labeled according
to classification
3. Safety of tools and equipment are observed in accordance with
manufacturer’s instructions
4. Conditions of PPE are checked in accordance with manufacturer’s
instructions.

CONTENTS:

● Types of Tools and Equipments

● Classification of functional and non-functional tools
● Uses of Personal Protective Equipment (PPE).

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Workplace location
● Tools and equipment related to the ff:
● Heavy equipment tools for repair
● Measuring instruments/equipments
● Instructional materials
● Handouts
● PowerPoint presentations

METHODOLOGIES:

● Lecture-demonstration
● Self-paced instruction
● Group discussion

ASSESSMENT METHODS:

● Oral questioning
● Direct observation
● Written test
LO2. PERFORM BASIC PREVENTIVE MAINTENANCE

ASSESSMENT CRITERIA:
1. Lubricants are identified according to types of equipment.
2. Tools and equipment are lubricated according to preventive maintenance
schedule or manufacturer’s specifications.
3. Measuring instruments are checked and calibrated in accordance with
manufacturer’s instructions.
4. Tools are cleaned and lubricated according to standard procedures
5. Defective equipment and tools are inspected and replaced according to
manufacturer’s specification.
6. Work place is cleaned and kept in safe state in line with OSHC regulations.

CONTENTS:
● Types uses of lubricants
● Types and uses of cleaning materials/solvent
● Types and uses of measuring instruments and equipment.
● Preventive maintenance techniques and procedures.
● OSHC workplace regulations

CONDITIONS:
Students/trainees must be provided with the following:
● Classroom for discussion
● Workplace location
● Kinds of manuals:
● Manufacturer's specification manual
● Repair manual
● Maintenance procedure manual
● Periodic maintenance manual
● Maintenance schedule forms
● Handouts/Instructional materials
● Maintenance materials, tools and equipment
● Lubricants
● Cleaning materials
● Rust remover
● Rugs
● Spare parts
● PPE

METHODOLOGIES:
● Lecture-demonstration
● Self-paced instruction
● Group discussion

ASSESSMENT METHODS:
● Oral questioning
● Direct observation
● Written test
LO3. STORE TOOLS AND EQUIPMENT

ASSESSMENT CRITERIA:

1. Inventory of tools, instruments, and equipment are conducted and recorded as

per company practices.
2. Tools are inspected, and replaced after use.
3. Tools and equipment are stored safely in accordance with manufacturer’s
specifications or company procedures.

CONTENTS:

● Inventory of tools and equipment

● Tools and equipment handling
● Tool safe-keeping/storage

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Handouts/instructional materials
● Workplace location/tool room
● Rack
● Tool box
● Forms
o Requisition slip
o Inventory form
o Inspection form

METHODOLOGIES:

● Demonstration
● Classroom discussions

ASSESSMENT METHODS:

● Practical examination
● Direct observation
● Written test/questioning
UNIT OF COMPETENCY : OBSERVE PROCEDURES, SPECIFICATIONS AND MANUALS OF
INSTRUCTIONS

MODULE TITLE : OBSERVE PROCEDURES, SPECIFICATIONS AND MANUALS OF

INSTRUCTIONS

TRAINING DURATION : 4 hours

MODULE DESCRIPTION : This module covers the knowledge, skills and attitudes on
identifying, interpreting, applying services to specifications
and manuals and storing manuals.

SUMMARY OF LEARNING OUTCOMES:

Upon completion of the module the trainees/student should be able to:

LO1. Identify, access, and interpret specification/manuals

LO2. Apply information in manual

LO3. Store manuals

LO1. IDENTIFY, ACCESS, AND INTERPRET SPECIFICATION/MANUALS

ASSESSMENT CRITERIA:

1. Manuals are identified and accessed as per job requirements.

2. Version and date of manual are checked to ensure that correct specification and
procedures are identified.
3. Relevant sections, chapters of specifications/manuals are located in relation to
the work to be conducted.
4. Information and procedure in the manual are interpreted in accordance with
industry practices.

CONTENTS:

● Types of manuals used in construction sector

● Different types of symbols.
● Accessing information and data.

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Manuals/catalogues relative to construction sector.
● Instructional materials

METHODOLOGIES:

● Classroom discussions/Lecture
● Self-paced

ASSESSMENT METHODS:

● Practical examination
● Written test/questioning
● Oral examination
LO2. APPLY INFORMATION IN MANUAL

ASSESSMENT CRITERIA:

1. Work steps are correctly identified in accordance with manufacturer’s

specification.
2. Manual data are applied according to the given task.
3. Adjustments are interpreted in accordance with information contained on the
manual or specifications.

CONTENTS:

● Manual/specification application.
● Interpreting specifications

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Manuals
● Workplace Location
● Measuring Instruments
● Instructional materials

METHODOLOGIES:

● Demonstration
● Classroom discussions
● Self-paced

ASSESSMENT METHODS:

● Practical examination
● Oral examination
● Written test/questioning
LO3. STORE MANUAL

ASSESSMENT CRITERION:

1. Manual or specification is stored appropriately to prevent damage, ready access

and updating of information when required in accordance with company
requirements.

CONTENT:

● Manual handling

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion.

● Manuals
● Store rooms/library
● Instructional materials

METHODOLOGIES:

● Demonstration
● Classroom discussions
● Self-paced

ASSESSMENT METHODS:

● Practical examination
● Direct observation
● Written test/questioning.
UNIT OF COMPETENCY : INTERPRET TECHNICAL DRAWINGS AND PLANS

MODULE TITLE : INTERPRETING TECHNICAL DRAWINGS AND PLANS

TRAINING DURATION : 3 hours

MODULE DESCRIPTION : This module covers the knowledge, skills and attitudes on
analyzing and interpreting symbols, data and work plan
based on the required performance standard.

SUMMARY OF LEARNING OUTCOMES:

Upon completion of the module the trainees/student should be able to:

LO1. Analyze signs, symbols and data.

LO2. Interpret technical drawings and plans

LO1. ANALYZE SIGNS, SYMBOLS AND DATA

ASSESSMENT CRITERIA:

1. Sign, symbols, and data are identified according to job specifications.

2. Sign, symbols and data are determined according to classification or as
appropriate in drawing.

CONTENTS:

● Drawing symbols and signs

● Trade mathematics

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Workplace Location
● Measuring Instruments
● Blueprints of plan
● Electrical
● Mechanical
● Instructional materials

METHODOLOGIES:

● Demonstration
● Classroom discussions
● Self-paced

ASSESSMENT METHODS:

● Practical examination
● Direct observation
● Written test/questioning
LO2. INTERPRET TECHNICAL DRAWINGS AND PLANS

ASSESSMENT CRITERIA:

1. Necessary tools, materials and equipment are identified according to the

plan.
2. Components, assemblies or object are recognized as per job requirement.
3. Dimensions and specification are identified according to job requirements.

CONTENTS:

● Basic technical drawing

● Technical plans and schematic diagram
● Symbols and abbreviations

CONDITIONS:

Students/trainees must be provided with the following:

● Classroom for discussion

● Workplace Location
● Measuring Instruments
● Blueprints of plan
● Electrical
● Mechanical
● Instructional materials

METHODOLOGIES:

● Demonstration
● Classroom discussions
● Self-paced

ASSESSMENT METHODS:

● Practical examination
● Direct observation
● Written test/questioning

MODULES OF INSTRUCTION

CORE COMPETENCIES

SYSTEM FORMWORK INSTALLATION NC II

UNIT OF COMPETENCY : ASSEMBLE AND DISMANTLE SCAFFOLDING/SHORING AND
BRACES

MODULE TITLE : ASSEMBLING AND DISMANTLING SCAFFOLDING/ SHORING AND BRACES

MODULE DESCRIPTOR : This module covers the knowledge, skills and attitude to carry-out
work activities in preparation for system formworks
installation according to industry standard. This include
planning and preparing for work; conducting operational
check; and perform effective erection and dismantling of
scaffold.

TRAINING DURATION : 40 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainees/student must be able to:

LO1. Plan and prepare for operation

LO2. Erect shoring/scaffolding

LO3. Inspect and replace defective shoring/scaffolding components

LO4. Dismantle shoring/scaffolding and clean up

LO1. PLAN AND PREPARE FOR OPERATION

ASSESSMENT CRITERIA:

1. Occupational Safety and Health Standards (OSHS) requirements consistent to

erect and dismantle shoring / scaffolding are verified and complied with
2. Site access and emergency routes are identified and confirmed.
3. Work instruction is reviewed, confirmed and clarified with authorized personnel.
4. Operation to erect and dismantle shoring / scaffolding is determined and
planned in line with job and site requirements.
5. Purpose of shoring / scaffolding is confirmed and associated activities are
identified.
6. Equipment is selected in accordance with work requirements.

CONTENTS:

● OH&S standards
● Company policies
● Scaffolding erection and dismantling procedures
● Types of scaffold/shoring and braces
● Determining loads
● 5’s and 3 R’s

CONDITIONS:

The students/trainees must be provided with the following:

● Work instructions
● Company policy manual
● OH&S manual
● Brochures of the different types of scaffolding
● Instructional materials

METHODOLOGIES:

● Classroom discussions
● Practical exercises
● Audio/video presentation

ASSESSMENT METHODS:

● Direct observation
● Written test/questioning
LO2. ERECT SHORING/SCAFFOLDING

ASSESSMENT CRITERIA:

1. Shoring /scaffolding and components are inspected, damaged components are

isolated, labeled, tagged and rejected.
2. Footings are prepared in accordance with OSHS requirements, codes of
practice, manufacturer specifications and engineer's instructions.
3. Shoring / scaffolding is set out and erected in accordance with OSHS
requirements and manufacturer specifications.
4. Fall protection devices are installed in accordance with job specification and
OSHS requirements.

CONTENTS:

● Scaffolding /shoring components

● Types of scaffold/shore defects
● Scaffolding load design
● Lifting devices
● Scaffolding/shoring erecting procedure
● OH&S standards
● Company policies
● Types of scaffolding

CONDITIONS:

The students/trainees must be provided with the following:

● Work instructions
● Tools and equipment
● Company policy manual
● OH&S manual
● PPE
● Scaffolding /shoring
● Labeling and tagging materials
● Brochures of the different types of scaffolding
● Instructional materials
● Workplace or simulated area

METHODOLOGIES:

● Classroom discussions
● Practical exercises
● Audio/video presentation

ASSESSMENT METHODS:

● Direct observation
● Written test/questioning
LO3. INSPECT AND REPLACE DEFECTIVE SHORING/ SCAFFOLDING COMPONENT

ASSESSMENT CRITERIA:

1. Faulty components are reported to appropriate personnel in line with company

safe operating procedure.
2. Shoring / scaffolding instability is reported to appropriate personnel in line with
company safe operating procedure.
3. Replacements of defective components are carried out.
4. Shoring / scaffolding checklist report is accomplished and submitted to
appropriate personnel following work procedures.

CONTENTS:

● Scaffolding /shoring components defects

● Shoring/scaffolding inspection procedure
● Shoring/scaffolding stability
● OH&S standards
● Report preparation
● Company policies
● Scaffolding erection and dismantling procedures

CONDITIONS:

The students/trainees must be provided with the following:

● Tools and equipment

● Shoring/ scaffolding components
● Work instructions
● Company policy manual
● OSH S manual
● PPE
● Report forms/checklist

METHODOLOGIES

● Classroom discussions
● Practical exercises
● Audio/video presentation

ASSESSMENT METHODS

● Direct observation
● Questioning
LO4. DISMANTLE SHORING/SCAFFOLDING AND CLEAN UP

ASSESSMENT CRITERIA:

1. Dismantling area is isolated with safety signs and barricades are put in
place.
2. Shoring / scaffolding is dismantled in accordance with engineering & safe
principles.
3. Work area is cleared and materials disposed of, re-used or recycled in
accordance with OSHS requirements, codes of practice and job specifications.
4. Tools and equipment are cleaned, checked, maintained and stored in
accordance with manufacturer recommendations and standard work practices.
5. Work completion procedures are applied and appropriate personnel notified
of work completion.
6. Advanced shoring / scaffolding operations and faults are recorded and
reported to the appropriate personnel.

CONTENTS:

● Good housekeeping
● Scaffolding/shoring dismantling procedures
● OSH standards
● Reusing/recycling of materials
● Work completion report
● Company policies

CONDITIONS:

The students/trainees must be provided with the following:

● Tools
● Cleaning tools and materials
● Work instructions
● Company policy manual
● OH&S manual
● Work area signs and barricades
● Instructional materials
● PPE
● Scaffolding
● Workplace or simulated area

METHODOLOGIES

● Classroom discussions
● Practical exercises
● Audio-video presentation

ASSESSMENT METHODS

● Direct observation
● Written test/questioning
UNIT OF COMPETENCY :INSTALL SYSTEM FORMWORK

MODULE TITLE :INSTALLING SYSTEM FORMWORK

MODULE DESCRIPTOR : This module covers the knowledge, skills and attitude in selecting
and preparing materials and tools for installing metal
formworks, Laying-out/assembling scaffolds and braces,
setting/fixing form panels of building components.

TRAINING DURATION : 40 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainee/student must be able to:

LO1.Prepare materials, tools and equipment for installing formworks

LO2.Perform setting out

LO3.Set/fix form system of structure components

LO4. Double check installed formwork systems

 LO1. PREPARE MATERIALS, TOOLS AND EQUIPMENT FOR INSTALLING FORMWORKS

ASSESSMENT CRITERIA:

1. Appropriate PPE is selected and used according to job requirements and

OSHS specifications.
2. Formworks components, power and hand tools and equipment are selected
and prepared consistent with job requirements.
3. Materials and other semi-consumables are re-checked and properly staged
according to job requirements.
4. Damaged materials are isolated and reported to immediate superior.
5. Unexpected situations are responded to in line with company rules and
regulations.
6. Housekeeping is performed according to safety regulations.

CONTENTS:

● Types of formwork systems

-Table form/Flying form
-System column formwork
-Horizontal panel systems
-Vertical panel systems
-Jump form
-Slip form
-Tunnel form
● Other systems
-Built-in –place suspended slab forming
-Gang forms
-Prefabricated panel formwork
-Knock-down forming
-Bridge construction- cast in place segmental, span –by –span /stepping
formwork
-One sided forms
● Other considerations
-Function of formworks
-Characteristics of good formworks
-Formworks safety
-Formworks components
-Typical materials used for formworks
-Requirements for material strength
-Advantages and disadvantages of metal and other formworks
-Semi- consumables materials for formworks
● Power and hand tools safe handling and preparations
● Tagging and coding
● Mensuration
● Formworks and other materials preparations and staging procedures
● Power and hand tools, and equipment uses
● Storage of formworks panels
● Contingency measures in the preparations of
● Workplace safety and best practices
CONDITIONS:

Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Compressor ● Sheathing (metal,
laminated plastic)
assembly
● Spirit level ● Saw (hand, circular) ● Shoring and
accessories
● Pull-push pen Personal protective ● Scaffolds and
Equipment (Gloves, accessories
● Plumb bob Safety shoes, ● Pencil
● Steel square Hard hat, Safety harness, ● Lumber plywood
● Tri-square Safety goggles) ● Nails
● Meter tape ● Form ties/ walers
● Level hose ● Form oil
● Audi video equipment ● Reference books,
● ● Modules, hands out,
multimedia materials.

METHODOLOGIES:

● Lecture/discussion
● Modular (self-pace learning)
● Return -demonstration

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Observation
● Demonstration
LO2. PERFORM SETTING OUT

ASSESSMENT CRITERIA:

1. Base line is established/ Identified according to the site layout.

2. Center line/location of columns/walls is established.
3. Dimension of footing (columns & walls) are established.
4. Defined locations are Marked-out using marking gauge or paints (columns/
walls).
5. Squareness of markings is checked.
6. Offset lines for checking purposes are set-up.

CONTENTS:

● Concrete elements and building systems

- Flat slabs
- Ribbed and waffle slabs
- Beams and slabs
- Post -tensioned slabs
- Tunnel form structures
● Types of worksite conditions
● Work area preparation and clearing procedures and techniques
● Establishing baseline,
● locating center-line of column and walls
● Dimensions and marking for footing, column, and walls
● Squreness of markings
● Workplaces safety ad best practices

CONDITIONS:

Students/trainees must be provided with the following:

Tools Materials
● Hammer ● Personal protective ● string lines
Equipment
(Gloves, Safety shoes,
Hard hat, Safety harness,
Safety goggles)

● Spirit level ● Leveling equipment ● Paint

● Plumb bob ● Paint rush

● Steel square
● Tri-square ● Reference books,
● Meter tape ● Modules, hands out,
multimedia materials.
● Level hose
METHODOLOGIES:

● Lecture/discussion
● Modular (self-pace learning)
● Return-demonstration
● Simulation

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Observation
● Demonstration
LO3. SET/FIX FORM SYSTEM OF STRUCTURE COMPONENTS

ASSESSMENT CRITERIA:

1. Appropriate PPE is selected and used according to job requirements and

OSHS specifications.
2. Form oil is applied to form panels or sheathing in accordance with
specifications.
3. Formworks components are set to the required alignment, squareness,
levelness, plumbness.
4. Connectors, braces and locks are properly secured according to job
requirements.
5. Unexpected situations are responded to in line with company rules and
regulations.
6. Housekeeping is performed according to safety regulations.
7. Formworks components are set to the required output at the given time.
8. Debris are removed in accordance to standard procedure.

CONTENTS:

● Formworks systems defects

- Sole plate
- Horizontal supports
- Vertical supports
- General
● Causes of formworks failures
- Improper stripping and shore removal
- Inadequate bracing
- Vibration
- Unstable soil under mudsills, shoring not plumb
- Inadequate control of concrete placement
- Lack of attention to formwork details
● Procedures on setting/fixing different types of formwork systems
● Steps in setting and fixing formwork /components assembly
- Sequence of assembly
- Alignments
- Levelness
- Plumbness
- Squareness
● Rigidity and stability and equilibrium of structure
● Connectors, braces and locks securing procedures and techniques
● Formworks setting procedures and techniques
● Oiling formwork
- Time of application
- Methods of application
● Installed formworks double –checking Procedures
● Formworks cleaning procedures and techniques
● Proper use of leveling instruments
● Stress on materials
- Flexibility
- Elasticity
- Axial forces
- Shear forces
CONDITIONS: Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Compressor and ● Sheathing (metal,
hoses laminated plastic)
assembly
● Spirit level ● Formworks ● Shoring and
components accessories
● Pull-push pen ● Saw (hand, circular) ● Scaffolds and
accessories
● Plumb bob ● Lifting equipment ● Pencil
● Steel square ● Personal protective ● Lumber plywood
● Tri-square Equipment ● Nails
● Meter tape (Gloves, Safety shoes, ● Form ties/ walers
Hard hat, Safety harness, ● bolts and nuts,
Safety goggles coach screws, masonry
anchors, metal brackets,
nails and spikes,
patented metal fasteners,
steel tie rods
● Level hose ● Form oil

METHODOLOGIES:

● Lecture/discussion
● Modular (self-pace learning)
● Return- demonstration
● Simulation

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Direct observation
● Demonstration
LO4 DOUBLE CHECK INSTALLED FORMWORK SYSTEMS

ASSESSMENT CRITERIA:

1. Installed formwork are double checked in accordance to job instruction.

2. Appropriate remedies/ adjustments are made to rectify non conformance to
standards.
3. Appropriate personnel are notified of the accomplished task.

CONTENTS:

● Checking of installed formworks

● Formworks defects/ non-conformance to standards
● Remedies and adjustments procedures on installed formworks
● Safety practices observed in the jobsite Lever/simple machines
● Work accomplished reporting procedure

CONDITIONS: Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Personal protective ● Plan and working
● equipment drawings
● Measuring tools ● Portable circular saw ● Lumber
● ● Scaffolding ● Nails
● Sledge hammer

METHODOLOGIES:

● Lecture /discussion
● Modular (self-pace learning)
● Return-demonstration
● Simulation

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Direct observation
● Demonstration
UNIT OF COMPETENCY : STRIP SYSTEM FORM WORK

MODULE TITLE : STRIPPING SYSTEM FORM WORK

MODULE DESCRIPTOR : This module covers the required competencies in preparing

staging area, tools and equipment, and in actual stripping
of meal formworks , shoring or/and re-shoring building
components.

TRAINING DURATION : 24 hours

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainee/student must be able to:

LO1.Prepare staging area, tools and equipment

LO2.Strip formworks of structure components

LO3.Shore or/and re-shore building components

LO1.PREPARE STAGING AREA, TOOLS AND EQUIPMENT

ASSESSMENT CRITERIA:

1. Work instruction is secured from immediate superior

2. Appropriate PPE is selected and used according to job requirements and OSHS
specifications.
3. Staging area is identified and prepared based on job requirements.
4. Tools are selected and prepared consistent with job requirements.
5. Unexpected situations are responded to in line with company rules and
regulations.
6. Housekeeping is performed according to safety regulations.

CONTENTS:

● Work instructions
● Staging area selection and preparation
● Proper storage and inventory of formwork components
● Types/kinds of power and hand tools/equipment are selected and prepared
consistent with job requirement
● Necessary action must be taken in response to actual situation
● Safe practices in the job site
● Types of PPE
● OHS specification relevant to job requirement
● Basic oral communication
● Filling-out forms

CONDITIONS:

Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Personal protective ● Modules/handouts
equipment reference books
● Scaffolding ● Audio video /
● Audio /video materials
multimedia equipment
● Open end wrench ● Lifting equipment ● Sample work forms
● Steel brush ● Paper and pencil

METHODOLOGIES:

● Lecture/discussion
● Modular (self-pace learning)
● Return-demonstration

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Direct observation
● Demonstration
LO2.STRIP FORMWORKS OF BUILDING COMPONENTS

ASSESSMENT CRITERIA:

1. Stripping permit is secured from immediate supervisor.

2. Formwork components and accessories are stripped carefully, safely and
sequentially.
3. Formwork components and accessories are sorted, arranged and properly
staged.
4. Formwork components and accessories are cleaned, refurbished, inventoried
and stored.
5. Formwork components and accessories which are beyond repair are discarded
for proper disposal.
6. Unexpected situations are responded to Housekeeping is performed according
to safety regulations.

CONTENTS:

● Cement curing theories

● Minimum setting time for:
- Walls
- Structural slabs
- Footings and foundations
- Earth supported foundations
● Procedure in stripping formworks
● Storage and inventory of formwork components
● Different types and uses of cleaning materials and equipment
● Necessary action must be taken in response to actual situation
● Safety procedures
● OHS regulations

CONDITIONS: Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Personal protective ● Sheathing
equipment (metal, laminated
plastic) assembly
● Claw bar ● Portable circular saw ● Shoring and
accessories
● Wrenches ● Lifting equipment ● Scaffolds and
accessories
● Audio /video
materials
● Sample work
forms
● Pencil
● Work instructions
METHODOLOGIES:

● Lecture/discussion
● Modular (self-pace learning)
● Return-demonstration
● Simulation

ASSESSMENT METHODS:

● Observation (oral/questioning )
● Demonstration
LO3.SHORE AND RE-SHORE BUILDING COMPONENTS

ASSESSMENT CRITERIA:

1. Appropriate PPE is selected and used according to job requirements and

OSHS.
2. Formworks structure components are re-shored where applicable.
3. Shores are removed in accordance with standard procedures.
4. Shores, tools and equipment are cleaned, maintained, inventoried and
stored properly.
5. Unexpected situations are responded to.
6. Housekeeping is performed according to safety regulations.

CONTENTS:

● Shoring /re-shoring theories and principles

● Steps in shoring and re-shoring
● Storage & inventory of tools & equipment
● Necessary action must be taken in response to actual situation
● Safety practices observed in the jobsite Lever/simple machines
● Basic oral communication
● Reading and interpreting brochures and manuals

CONDITIONS: Students/trainees must be provided with the following:

Tools Equipment Materials

● Hammer ● Personal protective ● Plan and working
● equipment drawings
● Measuring tools ● Portable circular saw ● Lumber
● ● Scaffolding ● Nails
● Sledge hammer

METHODOLOGIES:

● Lecture /discussion
● Modular (self-pace learning)
● Return-demonstration
● Simulation

ASSESSMENT METHODS:

● Interview (oral/questionnaire)
● Direct observation
● Demonstration

What is Competency-Based Curriculum (CBC)

●A competency-based curriculum is a framework or guide for the

subsequent detailed development of competencies, associated
methodologies, training and assessment resources.

●The CBC specifies the outcomes which are consistent with the
requirements of the workplace as agreed through the industry or
community consultations.

●CBC can be developed immediately when competency standards exist.

●When competency standards do not exist, curriculum developers need

to clearly define the learning outcomes to be attained. The standard
of performance required must be appropriate to industry and
occupational needs through the industry/enterprise or specified
client group consultations.

These materials are available in both printed and electronic copies.

For more information please contact:

Technical Education and Skills Development Authority (TESDA)
Telephone Nos.: 893-8281, 817-4076 to 82 loc. 611, 630, 631 and 635
or visit our website: www.tesda.gov.ph or the TESDA Regional or
Provincial Office nearest you.