Question 1

For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.6-3 Page 364, using LRFD, calculate the value of the interaction equation of the
given beam-column considering moment amplification factor B1 if the service axial compressive load
and bending moment are repaced by 278kips and 240kip-foot respectively. Use Fy=50ksi,
E=29000ksi, Ix=1110in4 , ФPn=1130kips, ФMn=646kip-foot. Express your answer in 4 decimal
places.

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
 Question 2
Steel truss members can be beam-column members.

TRUE

Question 3
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.6-12 Page 368, neglecting member's self weight, calculate the ratio of (Pu/ФPn) if
the 20kips and 40kips loads in the problem are changed to 131.5kips and 44.7kips respectively. Use
793kips as nominal compressive strength, 165kip-ft as nominal moment strength on major axis and
355kip-ft as nominal moment strength on minor axis of the member. Express your answer in 3
decimal places.

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
 Question 4
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.2-2 Page 364, using LRFD, calculate the maximum service liveload in KN/m that can
be supported if the beam span and compressive service deadload and liveload are repaced by 6m,
159KN and 215KN respectively. Use ASEP steel manual for W18x97 section properties. Fy of A992
steel is 345MPa. Use ФMn=1073.71 KN-m. Express your answer in 2 decimal places.

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
 Question 5
A 7.5m column is part of a braced frame with joint rotation carries service support end moments
of 147.4KN-m clockwise at top and 166.2KN-m clockwise at bottom. An additional axial
compressive service load of 591KN is also applied on the column. Bending is about major axis
only. The design compressive and bending strengths are 1836KN and 354KN-m respectively.
Fy=345MPa, E=200000MPa and Ix=458x106mm4. Calculate the moment correction factor or
reduction coefficient. Express your answer in 3 decimal places.

Question 6
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.6-12 Page 368, neglecting member's self weight, calculate the ratio of
(Mux/ФMnx+Muy/ФMny) if the 20kips and 40kips loads in the problem are changed to 131kips and
27.6kips respectively. Use 793kips as nominal compressive strength, 355kip-ft as nominal moment
strength on major axis and 165kip-ft as nominal moment strength on minor axis of the member.
Express your answer in 3 decimal places.

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
 Question 7
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.6-2 Page 364, using LRFD, calculate the moment amplification factor B1 if the beam
span and compressive service deadload and liveload are repaced by 6m, 157KN and 238KN
respectively. Use ASEP steel manual for W18x97 section properties. Fy of A992 steel is 345MPa. Use
ФMn=1073.71 KN-m. Express your answer in 4 decimal places.

Question 8
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui.
For Problem 6.6-3 Page 364, using LRFD, calculate the ultimate moment, Mu in kip-foot
considering moment amplification factor B1 if the service axial compressive load and bending
moment in the beam-column are repaced by 292kips and 229kip-foot respectively. Use Fy=50ksi,
E=29000ksi, Ix=1110in4 , ФPn=1130kips, ФMn=646kip-foot. Express your answer in 2 decimal
places.

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
 Question 9
An A36 W8x15 steel column, which is part of a braced frame is loaded with an eccentric load “Pu”
along the plane of the web "e" mm from its centroid. The column is laterally supported with Lb<Lp.
Using L=4.5m and k=0.7. Calculate the maximum eccentricity "e" in millimeters if the service dead
load,PDL =20.5KN and the PLL is twice as PDL. Do not consider amplification due to the effects of
secondary moments. Express your answer in 2 decimal places.

Question 10
In the analysis of a steel fixed-hinged column which is part of a braced frame subjected to transverse
loadings, which of the following values of moment reduction coefficient, Cm shall be adopted?

1.0

This study source was downloaded by 100000888018791 from CourseHero.com on 07-15-2024 20:52:11 GMT -05:00

https://www.coursehero.com/file/79940730/CW2D-Sol-1pdf/
Powered by TCPDF (www.tcpdf.org)