Portable 4-in-1 gas detector

Instruction manual

ADKS-4

1
1. Product introduction

This product has four kinds of gas detection sensors, which can detect
Ex(Explosive gas),H2S,CO,O2 through natural diffusion method. It has
excellent sensitivity and perfect repeatability, easy to use and maintain, and
can be used for industrial site safety monitoring.
The equipment has high reliability, and the shell can meet the requirements
of waterproof, dustproof and explosion-proof.
The detector is widely used in petroleum, chemical, environmental protection,
metallurgy, gas transportation, biochemistry, medicine and other industries

This product is designed, manufactured and calibrated in accordance with

the following Chinese standards:

GB/T3836.1-2021 Explosion environment part 1

GB/T3836.4-2021 Explosion environment part 4
GB15322.3-2019 Explosive gas detectors part 3
JJG693-2011,JJG365-2008,JJG695-2019,JJC915-2008,GB12358-2006

2. Structure and working principle

2.1 Structure & function

2
1 Alarm indicator light 5 Right button

2 Display screen 6 Menu

3 Charging port 7 Left button

4 Power button 8 Buzzer

9 Gas detection hole

3
2.2 Working principle: electric-chemical type and catalyze burning

type

3.Parameters

Ga Range Low Alarm High Alarm Resolution

s threshold threshold

Ex 0-100%L 20% 50%LEL 1% LEL

EL

H2 0-100pp 10ppm 20ppm 1ppm

S m

CO 0-1000pp 50ppm 200ppm 1ppm

O2 0-30%VO 19.5% VOL 23.5% VOL 0.1% VOL

For other types of gas, please contact us

4
Ex :Explosive gas

Error:±5% FS (Ex Explosive gas full-scale)

±10%（CO Carbonmonoxide）
±2μmol/mol or ±10% (H2S hydrogen sulfide)
Responding time: T < 45 Seconds
Indication :LCD display real-time data and status indicator, sound and
vibration alarm
Working environment:-20~50℃,RH<95%(no condensation)
Working voltage:3.7V Lithium ion battery
Explosion proof mark: Ex ib IIB T3
Charging time: 6h~8h
Detection time :16~18 hours
Working life of sensor: Ex,H2S,CO:2~3 years, O2:5 years
Size: 130*65*45(mm)
Weight: 0.5kg

4.Function and operation

4.1 Boot up
When the device is off, press the middle button for about 3 seconds, and the
back light of the display will light up.
With a beep, the screen displays a welcome screen.
4.2 Alarm threshold page
After entering the welcome interface, the screen will sequentially display the
high alarm threshold, low alarm threshold and detection range information of
combustible gas, oxygen, hydrogen sulfide and carbon monoxide.

5
 Ex alarm threshold O2 alarm threshold

H2S alarm threshold CO alarm threshold

4.3 Self test
After the end of the alarm threshold page, the device will enter the self-test
state.
In the process of self-test, the indicator light, vibration motor and buzzer are
started and closed twice according to the display prompts.

4.4 Detecting pages

After the self-test is completed, the test page will be entered, and the current
values of Ex(Explosive gas),H2S,CO,O2 gases will be displayed on the
screen.

4.5 Alarm
When the device detects that Ex, H2S, CO and O2 exceed the alarm
threshold, the indicator light and screen light up, the vibration motor starts,
and the buzzer sounds.

6
4.6 Status of equipment
Press the left button after entering the " Detecting " page to view the device
date, time and battery status.

4.7 Shutdown
Long press the middle button for 3 seconds on the detection page, and the
screen will display the shutdown interface. Left click to confirm shutdown,
right click to cancel.
4.8 Charging
When the battery voltage of the device is below 3.5V, the device will
automatically shut down. Charge the battery in time.
When the battery is full, the screen will display "Charge Over".

5. Menu operations

5.1 Press the middle key to enter the main menu interface
5.2 In the menu selection interface, the top button corresponds to the left
selection item of the display, the bottom button corresponds to the right
selection option of the display, and the middle button is the confirm, save or
enter sub-menu function
5.3 If you do not operate in the menu interface for more than 5 seconds after
entering the main menu, you will automatically return to the normal detection
interface.

7
Main menu structure and operations
The menu cursor can be moved by the top button and
the bottom button, and the middle button can enter the
selected menu item. If the cursor moves to "Exit", the
detection main interface can be returned.

Zero adjustment
This function is used to correct the zero drift of the
instrument by manually adjusting the compensation
value in the case of zero drift of the display value of the
instrument.
Move the cursor to the "Zero Adjust" menu item and
press the middle button to enter the correct password
in the password interface to enter the "Select Gas"
page.
Select the gas item that needs to be adjusted to Zero,
enter the "Zero Adjust" interface, press the left button to
select the digit to be adjusted, and press the right
button to adjust the value. Press the middle key to
save the current setting.
Note: The zero compensation value should not deviate
too much from the actual zero drift, otherwise the actual
display value will deviate too much.

8
Gas calibration
This function is for the internal use of the manufacturer
only.

Alarm threshold setting

Move the cursor to the menu item "Alarm Set" and
press the middle button to enter the "Select Gas"
interface to select the gas type to be set.
Enter the alarm threshold setting interface "Low" and
"High" to set the high alarm threshold and low alarm
threshold respectively. Press the key to move the
cursor position, press the up key to adjust the value,
and press the middle key to save the set value.

Alarm record
The menu of Alarm record includes three sub-menus:
"Alarm View", "Alarm Clear" and "Exit".
"Alarm View":Used to view the history of alarm records,
press the left button to scroll up, press the right button
to scroll down.
"Alarm Clear":Used to clear the alarm record, press the
left button to confirm the clear alarm record, press the
right button to cancel.
"Exit":Exit the current menu.

9
Date & Time Settings
Move the cursor to the "Time set" menu item and press
the middle key to enter the "Year ","
Month","Day","Hour" and "Min" setting menu items
respectively.

Language Settings
Move the cursor to the "Language" menu item and
press the middle button to enter the language selection
interface. You can switch between Chinese and
English menu languages.

10
 Factory Mode
This function is only for internal use by the
manufacturer

Restore factory default Settings

This function can restore all Settings to factory Settings

Warning: Do not charge in places where there may be flammable and

explosive gases, to prevent the arc generated by the charger interface from
causing fire or explosion.

6.Precautions in Use
6.1 During the operation of the device, the charging speed will slow down, so
it is recommended to shut down and charge.
6.2 When explosive gas seriously exceeds the range, the equipment may not
be able to detect correctly, and even cause sensor damage, so do not directly
use explosive gas with higher concentration such as lighter for detection.
6.3 Corrosive gases (such as high concentration of chlorine gas) may
damage the sensor, so avoid contact with such gases during storage or use,
and avoid using or storing this product under long-term high temperature,
high humidity and strong sunlight.
6.4 Do not wipe the product with corrosive solvents.
6.5 In order to ensure the detection accuracy, the machine should be

11
calibrated regularly, and the verification cycle should not exceed one year.
6.6 Non-professional personnel shall not disassemble this product.
6.7 This equipment is only used for gas leakage assessment of explosive gas,
not environmental explosive gas safety assessment instrument, and it is
prohibited to be used for assessing environmental explosive gas safety.
6.8 Some silicone rubber products contain sulfides and halogen volatiles that
may cause chemical poisoning of the sensor and lead to failure, so avoid
contact with such items when stored.
6.9 Drops or violent vibrations may permanently damage the equipment.

7. Storage environment
Equipment storage environment temperature -10~55℃, relative humidity less
than 85%, and good ventilation conditions, the air should not contain
corrosive harmful gases.

8. Packing accessories
1PCS packing box,1PCS host,1PCS charger,1PCS instruction manual,1PCS
certificate & warranty card.

9. The following detection gases can be customized

Gas Option range Resoluti Low alarm High alarm
on threshold threshold
O2 0~30%VOL 0.1%VO 19.5 23.5
L
CH4 0~4%VOL 0.01%V 1.0 2.5
OL
CO 0~1000ppm 1ppm 50 200
H2S 0~100ppm 0.1ppm 10 20
EX 0~100%LEL 1%LEL 20 50
NH3 0~100ppm 0.1ppm 20 50

12
H2 0~1000ppm 0.1ppm 200 500
Cl2 0~20ppm 0.1ppm 5 10
HCl 0~20ppm 0.1ppm 5 10
SO2 0~20ppm 0.1ppm 5 10
NO 0~250ppm 0.1ppm 20 125
NO2 0~20ppm 0.1ppm 5 10
CO2 0~5000PPM 0.1%VO 0.2%VOL 0.5%VOL
L
PH3 0~20ppm 1ppm 5 10
HC 0~50ppm 1ppm 10 25
N
C2H4 0~100ppm 1ppm 20 50
O
O3 0~100ppm 0.1ppm 20 50
CH2 0~40ppm 0.1ppm 8 20
O
C6H6 0~1000ppm 1ppm 200 500
C7H8 0~1000ppm 1ppm 200 500
C8H1 0~1000ppm 1ppm 200 500
0
VOC 0~1000ppm 1ppm 200 500
C2H3 0-250ppm 1ppm 50 125
Cl
CH3 0-30ppm 1ppm 6 15
OH/
CH4
O
C4H8 0-90ppm 1ppm 18 45
C2H6 0-80ppm 1ppm 16 40

13
O
The test range of the customized instrument is subject to the actual factory

14