(F) MASONRY AND CONCRETE BLOCKS NOTES:

1. CONCRETE HOLLOW BLOCKS, UNLESS OTHERWISE SPECIFIED SHALL BE 150MM 01. ACI SECTION 12.4 STATES THAT:
THICK. LOAD BEARING BLOCKS SHALL HAVE A MINIMUM COMPRESSIVE STRENGTH OF DEVELOPMENT LENGTH OF INDIVIDUAL BARS WITHIN A BUNDLE IN TENSION OR COMPRESSION SHALL BE
750 PSI (5.175 MPa) WHILE NON-LOAD BEARING SHALL HAVE A MINIMUM THAT FOR THE INDIVIDUAL BAR. INCREASED TWENTY PERCENT (20%) FOR THREE-BAR BUNDLE AND
COMPRESSIVE STRENGTH OF 400 PSI (2.76 MPa). THIRTY THREE PERCENT (33%) FOR FOUR-BAR BUNDLE.
2. PROVIDE 1-16MMØ VERTICAL BARS AT CORNERS, INTERSECTIONS, END OF WALLS,
EACH SIDE OF OPENINGS. 02. FOR COLUMNS AT ANY LEVEL NO MORE THAN ALTERNATE BARS SHOULD BE SPLICED NOT MORE THAN
3. LINTEL BEAMS SHALL BEAR AT LEAST 200MM (8") ON EACH SIDE OF MASONRY WALL THIRTY PERCENT (33%) OF THE BARS SHALL BE SPLICED WITHIN THE REQUIRED LAP LENGTH MINIMUM
OPENING. DISTANCE BETWEEN TWO ADJACENT BAR SPLICES SHALL BE 600mm.
4. WALL REINFORCEMENTS SHALL BE AS FOLLOWS:
03. TOP BARS ARE HORIZONTAL BARS WITH MORE THAN 300mm DEPTH OF CONCRETE CAST BELOW THE
WALL THICKNESS VERTICAL BARS HORIZONTAL BARS REINFORCEMENT.
8 IN. (200 mm) . . . . . . . . . . 12MMØ @ 400 mm 10MMØ @ 600 mm
6 IN (150 mm) . . . . . . . . . . . 10MMØ @ 400 mm 10MMØ @ 600 mm 04. AS MUCH AS POSSIBLE SPLICES SUBJECTED TO TENSILE STRESSES ARE DISCOURAGE.
4 IN. (100 mm) . . . . . . . . . . 10MMØ @ 400 mm 10MMØ @ 600 mm THESE SHOULD BE AVOIDED OR PROVIDED WITH STANDARD HOOKS.

5. BLOCK WALL REINFORCING BARS SHALL BE LAPPED OF 30 BAR DIAMETERS WHERE 05. ASSUMED SPECIFIED COMPRESSIVE STRESS FOR CONCRETE fc'=3,000 Psi.
SPLICED, HORIZONTAL/VERTICAL DOWELS FROM FOOTINGS, COLUMNS/WALLS OR
SLABS SHALL EXTEND INTO THE BLOCK WALL A MINIMUM OF 30 BAR DIAMETERS OR A
MINIMUM OF 400MM WHICHEVER IS LONGER AND DOWELS TO MATCH VERTICAL
REINFORCEMENTS OF WALL.

(G) STRUCTURAL STEEL SPLICING AND ANCHORAGE LENGTH SCHEDULE:

LAP SPLICES (M) Min. Lap Splice
1. ALL STRUCTURAL STEELS SUCH AS ANGLES, WIDE FLANGE SECTIONS, PIPES, BAR ANCHORAGE
STANDARD
HOOK UNIT Length of Col. Rein.
STIFFENER PLATES, BASE PLATES, ETC. SHALL CONFORM TO ASTM A-36. DIAMETER LENGTH (M) TENSION BAR TENSION BAR WEIGHT Individual Bars
(mm) (M) (kg/m)
2. ALL STRUCTURAL STEEL SHALL BE DETAILED, FABRICATED AND ERECTED BASED ON 90 DEG 180 DEG 133 DEG TOP BAR BOT BAR TOP BAR BOT BAR W/ TIES W/ SPIRAL
THE SPECIFICATION FOR DESIGN, FABRICATION, AND ERECTION OF STRUCTURAL
STEEL GIVEN BY THE NATIONAL STRUCTURAL CODE OF THE PHILIPPINES (NSCP). 10 0.60 0.10 0.13 0.10 0.42 0.30 0.42 0.30 0.617 0.30 0.30
3. CONNECTION BOLTS ( 3/4 ROUND, UNLESS SHOWN OTHERWISE) SHALL CONFORM TO
12 0.60 0.14 0.16 0.12 0.42 0.30 0.42 0.30 0.889 0.30 0.30
ASTM A-325. ANCHOR BOLTS (EMBEDDED IN MASONRY OR CONCRETE) SHALL
CONFORM TO ASTM A307 UNLESS NOTED OTHERWISE ON THE DRAWINGS. 16 0.60 0.22 0.18 0.14 0.73 0.52 0.87 0.62 1.580 0.52 0.47
4. ALL STRUCTURAL STEEL SHALL BE CLEAN, RUST FREE AND SHOP COATED WITH THE
20 0.60 0.30 0.20 0.20 0.91 0.65 1.10 0.78 2.469 0.65 0.58
APPROPRIATE PAINT. STRUCTURAL STEEL AND ANCHOR BOLTS SHALL BE MINIMUM
ASTM A-36 DOMESTIC, LATEST REVISION. 25 0.68 0.40 0.28 0.26 1.40 1.00 1.40 1.00 3.858 0.80 0.73
5. NON - SHRINK GROUT - PRE-MIXED, NON-METALLIC, CEMENT-BASED GROUT, MEETING
28 0.86 0.48 0.38 1.76 1.26 1.53 1.09 4.840 0.90 0.82
THE REQUIREMENT OF ASTM C827, ASTM C109 & CRD-C621, WITH A MINIMUM
COMPRESSIVE STRENGTH OF 7000psi AT 28 DAYS. 32 1.12 0.56 0.43 2.31 1.65 1.74 1.24 6.327 1.03 0.93
6. PROVIDE MISCELLANEOUS PLATES, ANGLES AND ANCHORS AS SHOWN OR NOTED ON
36 1.38 0.61 0.48 2.95 2.10 2.00 1.40 8.000 1.20 1.05
DRAWINGS.
7. ALL CUTTING AND BLOCKING OF STEEL SHALL BE SHOWN ON SHOP DRAWINGS AND
PERFORMED IN SHOP.
8. PROVIDE TEMPORARY BRACING AS REQUIRED FOR A SAFE STRUCTURE UNTIL ALL
FINAL CONNECTIONS ARE MADE.

SCHEDULE OF BEAMS: SCHEDULE OF FOOTINGS:

fc' = 4,000 Psi (27.58 MPa)
Fy = 40,000 Psi Fy = 40,000 Psi (275.79 MPa)
fc' = 4,000 Psi

FLOOR BEAM SECTION LONGITUDINAL REINFORCEMENT REINFORCING BARS

LEVEL BEAM BAR Ø

WEB STIRRUPS STIRRUPS
WIDTH DEPTH
BARS STIRRUP SPACING REMARKS FOOTING WIDTH LENGTH THICK DEPTH OF
LOCATION MARK DISCONT. CONT. MIDSPAN CONT. DISCONT. EACH FACE
NO./SET Ø
NO. (M) (M) (M) ALONG LENGTH ALONG WIDTH EXCAVATION (M)
(B) (D) "A" "A" "B" "B"
TOP BARS BOT. BARS TOP BARS BOT. BARS

TB 3 3 2 3 3
R-1 200 300 16 1 10 2-50; 5-100; REST-200 to C.L. F1 1.10 1.10 0.30 - 6- Ø16mm - 6- Ø16mm 1.10
ROOF BB 2 2 3 2 2

BEAM TB 5 5 3 5 5
F2 0.90 1.00 0.25 - 5 - Ø16mm - 5 - Ø16mm 1.00

LEVEL R-2 200 300 16 1 10 2-50; 5-100; REST-200 to C.L.

BB 3 3 5 3 3
Note:
LB-1 TB 2 2 2 2 2 All foundation shall rest on natural soil. No part of the foundation shall rest on fill.
150 300 16 1 10 2-50; 5-100; REST-200 to C.L. Assumed Allowable Soil Bearing (fc') = 100 KN/m²
BB 2 2 2 2 2

APPROVED BY: (SEC. 33 OF R.A. NO. 9266) PROJECT TITLE: SHEET CONTENT: DRAWN BY: SHEET NO.
DESIGNED BY:
OLLYN E. FELIPE, UAP ALL DESIGNS, DRAWING, MODELS, SPECIFICATIONS AND

S2
ARCHITECT
OTHER CONTRACT DOCUMENTS AND COPIES THEREOF,
PREPARED, DULY SIGNED, STAMPED AND SEALED AND
CADD BY:
ZYRILLE B. RARO
FURNISHED AS INSTRUMENTS OF SERVICE, ARE THE

PRC NO: VALIDITY:

INTELLECTUAL PROPERTY AND DOCUMENTS OF THE
ARCHITECT, WHETHER THE WORK FOR WHICH THEY CHECKED BY: B.S. ARCHITECTURE 3B
WHERE MADE IS EXECUTED OR NOT, AND ARE NOT TO
PTR NO: DATE ISSUED: BE REPRODUCED OR USED ON OTHER WORK EXCEPT
DATE:
PLACE ISSUED: TIN: WITH A WRITTEN AGREEMENT WITH THE ARCHITECT.