Savitribai Phule Pune University

(Formerly University of Pune)

DEPARTMENT OF TECHNOLOGY

Practical manual
of
Basics of Electronics
 INDEX
S.NO NAME OF THE EXPERIMENT PAGE NO.
1 Forward and Reverse Characteristics of PN Junction Diode. 1-8
2 Zener Diode Characteristics and Zener as Voltage Regulator 9-16
3 Input & Output Characteristics of Transistor in CB 1-25
Configuration.
4 Input & Output Characteristics of Transistors in CE 26-33
Configuration
5 Half Wave Rectifier with & without Filters 34-40
6 Full Wave Rectifier with & without Filters 41-47
7 FET Characteristics 48-55
8 Design of self-bias circuit 56-59
9 Frequency Response of CC Amplifier 60-67
10 Frequency Response of CE Amplifier 68-74
11 Frequency Response of Common Source FET Amplifier 75-80
12 SCR Characteristics 81-85
13 UJT Characteristics 86-92
 Basics of Electronics (BTDS103)
Savitribai Phule Pune University (DOT)
DODEPARTMENT OF TECHNOLOGY

EXPT NO: 1.

FORWARD & REVERSE BIAS CHARACTERISTICS OF PN JUNCTION DIODE

AIM: -
1. To study the characteristics of PN junction diode under
a) Forward bias. b) Reverse bias.
2. To find the cut-in voltage (Knee voltages) static & dynamic resistance in forward &
reverse direction.

COMPONENTS & EQUIPMENT REQUIRED: -

S.No Device Range/Rating Qty

1. Regulated power supply voltage 0-30V 1
2. Voltmeter 0-1V or 0-20V 1
3. Ammeter 0-10mA,200mA 1
4. Connecting wires & breadboard
5 Diode In4007,OA79
6 Resistors 1k,10k

THEORY:

The V-I characteristics of the diode are curves between voltage across the diode and current
through the diode. When the external voltage is zero, the circuit is open and the potential barrier
does not allow the current to flow. Therefore, the circuit current is zero. When the P-type (Anode
is connected to the +ve terminal and n- the type (cathode) is connected to the –ve terminal of the
supply voltage, is known as forward bias. The potential barrier is reduced when the diode is in the
forward-biased condition. At some forward voltage, the potential barrier is altogether eliminated
and current starts flowing through the diode and also in the circuit. The diode is said to be in
the ON state. The current increases with increasing forward voltage. When the N-type (cathode)
is connected to the +ve terminal and the P-type (Anode) is connected –ve terminal of the supply
voltage is known as reverse

BTech Data Science 2024 Page -2

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University (DOT)
DODEPARTMENT OF TECHNOLOGY
Bias and the potential barrier across the junction increase. Therefore, the junction resistance
becomes very high and a very small current (reverse saturation current) flows in the circuit. The
diode is said to be in an OFF state. The reverse bias current is due to minority charge carriers. The
p-n junction diode conducts only in one direction.

CIRCUIT DIAGRAM:

FORWARD BIAS:-

REVERSE BIAS:-

Department of Technology Page -3

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY

MODEL WAVEFORM:-

PROCEDURE: -

Forward bias characteristics

1. Connect the circuit diagram as shown in the figure for Forward bias using a silicon
diode.
2. Now vary RPS supply voltage Vs in steps from 0V onwards (0.1V,0.2V……1V) note
down the forward current (If) through the diode for different Forward voltages (Vf)
across the diode without exceeding the rated value (If Max=20mA)
3. Tabulate the results in the tabular form.
4. Plot the graph between Vf & If.
5. Repeat the above steps 4 steps by using Germanium diode.

Reverse bias characteristics

1. Connect the circuit diagram as shown in the figure for Reverse bias using a silicon diode.
2. Now vary RPS supply voltage Vs in steps from 0V onwards (1V,2V……10V) note down
the forward current (Ir) through the diode for different Reverse voltages (Vr) across the
diode without exceeding the rated value (Vr Max=15V)
3. Tabulate the results in the tabular form.
BTech Data Science 2024 Page -4
Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
4. Plot the graph between Vr & Ir.
5. Repeat the above steps 4 steps by using Germanium diode.

PRECAUTIONS:
1. Avoid loose connections use proper voltmeter & ammeters

TABULAR COLUMN:

SL. No APPLIED VOLTAGE VOLTAGE ACROSS CURRENT

(V) DIODE (V) THROUGH
DIODE(mA)
0 0
1 0.1
2 0.2
3 0.3
4 0.4
5 0.5
6 0.6
7 0.7
8 0.8
9 0.9
10 1
11 2
12 3
13 4
14 5
15 6
16 7
17 8
18 9
19 10
20 11

BTech Data Science 2024 Page -5

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY

TABULAR COLUMN:

SL. No APPLIED VOLTAGE VOLTAGE ACROSS CURRENT

(V) DIODE (V) THROUGH
DIODE(uA)
0 0
1 0.1
2 0.2
3 0.3
4 0.4
5 0.5
6 0.6
7 0.7
8 0.8
9 0.9
10 1
11 2
12 3
13 4
14 5
15 6
16 7
17 8
18 9
19 10
20 11

RESULT: -

BTech Data Science 2024 Page -6

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:

1. What is a P-N junction diode?

2. What is doping why is doping necessary?
3. Difference between P-type and N-type semiconductor materials?
4. What is the diode equation?
5. What is an ideal diode?
6. Define the depletion region of a diode.
7. What is meant by the transition & space charge capacitance of a diode?
8. Is the V-I relationship of a diode Linear or Exponential?
9. Define the cut-in voltage of a diode and specify the values for Si and Ge diodes.
10. What are the applications of a p-n diode?
11. Draw the ideal characteristics of the P-N junction diode.
12. What is the diode equation?
13. What is the breakdown voltage?
14. What is the effect of temperature on PN junction diodes?
15. What is PIV?
16. What is Forward bias?
17. What is Reverse bias?
18. What is Forward voltage?
19. What is Reverse current?
20. What is an ideal diode?
21. What is Breakdown voltage?
22. What is cut-in voltage?
23. Is the V-I relationship of a diode Linear or Exponential?
24. Define diode?
25. What are the characteristics of a diode?
26. Draw the ideal characteristics of the P-N junction diode.
27. What are the diode characteristics?
28. What is the breakdown voltage in a diode?
29. What is the effect of PN junction diodes?
30. What is PVI?

BTech Data Science 2024 Page -7

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
Design Problems
1. Forward and reverse bias characteristics of Si diode with 1N4007.
2. Forward and reverse bias characteristics of Ge diode.
3. Forward and reverse bias characteristics of Si diode with VD = 10 V and ID = 10 mA
4. Forward and reverse bias characteristics of Ge diode with VD = 5 V and ID = 10 mA
5. Forward and reverse bias characteristics of Si diode with R = 500 Ohms
6. Forward and reverse bias characteristics of Si diode with R = 1.5K
7. Forward and reverse bias characteristics of Si diode with R = 2K
8. Forward and reverse bias characteristics of Si diode with VRPS = 0 – 10V
9. Forward and reverse bias characteristics of Si diode with VRPS = 0 – 5V
10. Forward and reverse bias characteristics of Si diode with 1N4008.
11. Find the cut-in voltage for the given diode in forward bias.
12. Find the cut in voltage for the given diode in forward bias when the input resistance is 1K
13. Find the cut in voltage for the given diode in forward bias when the input resistance is 1K
14. Prove that the P-N junction Diode acts as an isolator
15. Prove that the P-N junction diode acts as on Switch when it is in forward bias
16. Prove that the P-N junction diode acts as an off Switch when it is in Reverse bias
17. Find the change in cut-in voltage when input resistance is varied from 1k to 1M
18. Prove that Ohm law is verified for the P-N junction diode in forward-biased condition.
19. Find the static resistance of the P-N junction Diode
20. Find the Dynamic resistance of P-N junction Diode
21. Forward and reverse bias characteristics of Ge diode with 1N4007.
22. Reverse and Forward bias characteristics of Ge diode.
23. Forward and reverse bias characteristics of Si diode with VD = 20 V and ID = 10 mA
24. Forward and reverse bias characteristics of Ge diode with VD = 10 V and ID = 10 mA
25. Forward and reverse bias characteristics of Si diode with R = 50 Ohms
26. Forward and reverse bias characteristics of Si diode with R = 2.5K
27. Forward and reverse bias characteristics of Si diode with R = 5K
28. Forward and reverse bias characteristics of Si diode with VRPS = 0 –210V
29. Forward and reverse bias characteristics of Si diode with VRPS = 0 – 1V
30. Forward and reverse bias characteristics of Ge diode with 1N4008.

BTech Data Science 2024 Page -8

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
REALTIME APPLICATIONS:

1. PN junction (which has a direct energy band gap) in forward biased

condition produces
light when biased with a current. All LED lighting uses a PN junction diode.

2. The voltage across a PN junction biased at a constant current has a negative

temperature coefficient. The difference between the PN junction voltages of two
differently biased diodes has a positive temperature coefficient. These properties
are used to create Temperature Sensors and reference voltages (Bandgap).

3. Various circuits like Rectifiers, Varactors for Voltage Controlled Oscillators (VCO),
etc.

BTech Data Science 2024 Page -9

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 2.

ZENER DIODE CHARACTERISTICS

AIM: -
1. To study the volt-Ampere characteristics of a given Zener diode under
a) Forward bias. b) Reverse bias.
2. To find the Zener breakdown voltage in reversed biased condition.

EQUIPMENTS & COMPONENTS REQUIRED: -

S.No Device Range/Rating Qty

1. a) Regulated DC supply voltage 0-30V 1
b) Diode 1N4735A or BZ6.2v,5.6v 12
c) Resistors or 3.9V 1
1k,10k
2. Voltmeter 0-1V,0-20V 1
3. Ammeter 0-10mA,200mA 1
4. Connecting wires & breadboard

Theory:-

A Zener diode is a heavily doped p-n junction diode, specially made to operate in the
breakdown region. A p-n junction diode normally does not conduct when reverse-biased. But if
the reverse bias is increased, at a particular voltage it starts conducting heavily. This voltage is
called Breakdown Voltage. High current through the diode can permanently damage the device.
To avoid a high current, we connect a resistor in series with a Zener diode. Once the diode starts
conducting it maintains almost constant voltage across the terminals whatever may be the current
through it, i.e., it has very low dynamic resistance. It is used in voltage regulators. It is also called
a stabilizer diode or stabilization or constant voltage device.
Zener diodes are more heavily doped (around 1 x105) as compared to ordinary diodes (1
x108) and they have a narrow depletion layer.
The breakdown mechanisms are of two types.
(i) avalanche breakdown
(ii) Zener break down

BTech Data Science 2024 Page -10

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
(iii) In avalanche breakdown mechanism, thermally generated electrons & holes acquire
sufficient energy from the applied potential to produce new carriers by removing
valance electrons from their bonds. These new carriers, in turn produce new carriers
(called avalanche multiplication).

In Zener breakdown mechanism, very high electric field intensity across the narrow
depletion region directly forces carries out of their bonds.
During breakdown the voltage across the diode remains constant, independent to the current that
flows through it. Because of this property a Zener diode serves as Voltage Stabilizer or voltage
reference and break down occurs by avalanching in Zener diodes having break down voltages
greater than 8V. It occurs by a combination of both mechanisms when breakdown voltage is
between 5V & 8V. Zener effect play a very important role only in the diodes with breakdown
voltages below about 5V.Zener breakdown voltages decreases with increased temperature where
as avalanche breakdown voltage increases with increased temperature. Zener diode operates in
either a ‗ON‘ state or ‗OFF‘ state

CIRCUIT DIAGRAM:

STATICCHARACTERISTICS:-

BTech Data Science 2024 Page -11

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
REGULATION CHARACTERISTICS:-

MODEL WAVEFORMS:-

BTech Data Science 2024 Page -12

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
PROCEDURE: -

Forward bias characteristics

1. Connect the circuit diagram as shown in figure for Forward bias using zener diode
2. Switch on the RPS supply voltage Vs and vary in steps from 0V onwards (0.1V,
0.2V……1V) note down the forward current (If) through the diode for different forward
Voltages (Vf) across the diode without exceeding the rated value (Vs=10V)
3. Tabulate the results in the tabular form.
4. Plot the graph between Vf & If.
Reverse bias characteristics

1. Connect the circuit diagram as shown in figure for Reverse bias using Zener diode.
2. Now vary RPS supply voltage Vs in steps from 0V onwards (1V, 2V……10V) note
down the Reverse current (Ir) through the diode for different Reverse voltages (Vr)
across the diode without exceeding the rated value (Vr Max=15V)
3. Tabulate the results in the tabular form.
4. Plot the graph between Vr & Ir
TABULAR COLUMN: Forward Bias

SL. No APPLIED ZENER VOLTAGE ZENER

VOLTAGE(V)VOLTS (Vz)VOLTS CURRENT(Iz)mA
1 0
2 0.1
3 0.2
4 0.3
5 0.4
6 0.5
7 0.6
8 0.7
9 0.8
10 0.9
11 1
12 2
13 3
14 4
15 5
16 6
17 7
18 8

BTech Data Science 2024 Page -13

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
19 9
20 10

TABULAR COLUMN: Reverse Bias

SL. No APPLIED ZENER VOLTAGE ZENER

VOLTAGE(V)VOLTS (Vz)VOLTS CURRENT(Iz)mA
1 0.1
2 0.2
3 0.3
4 0.4
5 0.5
6 0.6
7 0.7
8 0.8
9 0.9
10 1
11 2
12 3
13 4
14 5
15 6
16 7
17 8
18 9
19 10
20 11

PRECAUTIONS:
Avoid loose connections use proper voltmeter & ammeters

RESULT: -

BTech Data Science 2024 Page -14

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS: -

1. What is Zener diode?

2. Can Zener be used as a rectifier?
3. What are the voltage ratings of Zener diode?
4. Give advantages of Zener diode?
5. How Zener diode behaves in forward bias?
6. What type of temp? Coefficient does the Zener diode have?
7. If the impurity concentration is increased, how the depletion width effected?
8. Does the dynamic impendence of a Zener diode vary?
9. Explain briefly about avalanche and Zener breakdowns?
10. Draw the Zener equivalent circuit?
11. Differentiate between line regulation & load regulation?
12. In which region Zener diode can be used as a regulator?
13. How the breakdown voltage of a particular diode can be controlled?
14. What type of temperature coefficient does the Avalanche breakdown has?
15. By what type of charge carriers the current flows in Zener and avalanche breakdown
diodes?
16. What is static characteristics of diode?
17. Can Zener be used as an integrator?
18. What are the rating voltages of Zener diode?
19. Give disadvantages of Zener diode?
20. How Zener diode behaves in forward bias?
21. What type of temp Coefficient does the Zener diode have?
22. If the impurity concentration is decreased, how the depletion width effected?
23. Does the dynamic impendence of a diode vary?
24. Explain briefly about avalanche breakdown?
25. Draw the Zener equal circuit?
26. Differentiate between line & load regulation?
27. In which region Zener diode can be used as a integrator?
28. How the cut in voltage of a particular diode can be controlled?
29. What type of temperature coefficient does the Zener breakdown has?

BTech Data Science 2024 Page -15

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
30. what type of charge carriers the voltage flows in Zener and avalanche breakdown diodes?

Design Problems
1. Reverse bias characteristics of Zener Si diode with 5.6V.
2. Reverse bias characteristics of Zener Si diode with 6.2V.
3. Reverse bias characteristics of Zener Si diode with 5.6V with R = 2K.
4. Reverse bias characteristics of Zener Si diode with 5.6V with R = 2.5K.
5. Verify the operation of Zener acts as voltage regulator.
6. Verify the operation of Zener acts as voltage regulator with R = 2K and RL = 5K
7. Reverse bias characteristics of Zener Si diode with 5.6V with VRPS = 0 – 15V
8. Reverse bias characteristics of Zener Si diode with 5.6V with VRPS = 0 – 20V
9. Reverse bias characteristics of Zener Si diode with 6.2V with VD = 10 V and ID = 10 mA
10. Reverse bias characteristics of Zener Si diode with 6.2V with VD = 20 V and ID = 15 mA
11. Find the difference between P-N junction Diode and Zener diode in forward bias
condition
12. Find the difference between P-N junction Diode and Zener diode in Reverse bias
condition
13. Find the Break down voltage for given Zener Diode.
14. Plot the Reverse Bias characteristics for the Zener diode when I/P resistance is 10k
15. Find the effect of change in characteristics of Zener diode connected in Reverse Bias
condition when input resistance is changed from 10k to 20K
16. Find the effect of change in characteristics of Zener diode connected in Reverse Bias
condition when input resistance is changed from 20k to 10K
17. Reverse bias characteristics of Zener Si diode with 6.2V with VD = 12 V
18. Find output voltage of Zener Si diode with 6.2V with VD = 10V
19. Find output voltage of Zener Si diode with 6.2V with VD =5V
20. Find output voltage of Zener Si diode with 6.2V with VD =6.2V
21. Reverse bias characteristics of Zener Si diode with 6.5V.
22. Reverse bias characteristics of Zener Si diode with 2.6V.
23. Reverse bias characteristics of Zener Si diode with 2.6V with R = 1K.
24. Reverse bias characteristics of Zener Si diode with 2.6V with R = 2.0K.

BTech Data Science 2024 Page -16

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
25. Verify the operation of Zener acts as voltage integrator.
26. Verify the operation of Zener acts as voltage regulator with R = 1K and RL = 2K
27. Reverse bias characteristics of Zener Si diode with 2.6V with VRPS = 0 – 10V
28. Reverse bias characteristics of Zener Si diode with 2.6V with VRPS = 0 – 10V
29. Reverse bias characteristics of Zener Si diode with 2.2V with VD = 20 V and ID = 5 mA
30. Reverse bias characteristics of Zener Si diode with 6.2V with VD = 10 V and ID = 10 mA

REALTIME APPLICATIONS:
1. Android based projects are being preferred these days. These projects involve use of
Bluetooth technology based device. These Bluetooth devices require about 3V voltage for
operation. In such cases, a Zener diode is used to provide a 3V reference to the Bluetooth
device.
2. Another application involves use of Zener diode as a voltage regulator. Here the AC voltage is
rectified by the diode D1 and filtered by the capacitor. This filtered DC voltage is regulated by
the diode to provide a constant reference voltage of 15V. This regulated DC voltage is used to
drive the control circuit, used to control the switching of light, as in an automated lighting
control system.

BTech Data Science 2024 Page -17

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 3.

INPUT & OUTPUT CHARACTERISTICS OF TRANSISTOR IN COMMON BASE

CONFIGURATION

AIM: -

1. To study the input and output characteristics of transistor (BJT) connected in common
base configuration
2. To calculate current gain α.
3. To calculate input resistance Ri & output resistance Ro.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty
1. Regulated DC supply voltage(RPS) 0-30V 1
2. Voltmeter 0-1Vor 0-10v ,0-20V 2
3. Ammeter 0-10mA,200mA 2
4. Connecting wires & bread board
5 Transistor BC 107 or 2n2222 or BC547 NPN 1
6 Resistor 1K,10K 1

Theory: -

The name transistor is derived from TRANSFER RESISTOR. [A transistor transfers a

signal level of resistance to another level of resistance]
A transistor is a three terminal active device. The terminals are emitter, base, collector. In CB
configuration, the base is common to both inputs (emitter) and output (collector). For normal
operation, the E-B junction is forward biased and C-B junction is reverse biased.
There are two types of transistors made of either Ge or Si
i. NPN transistor.
ii. PNP transistor.
NPN and PNP transistors are called Complementary transistors

BTech Data Science 2024 Page -18

Savitribai Phule Pune University (DOT) Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY
A transistor can be connected in a circuit in the following three ways depending on which
terminal is common to input and output.
i. common base configuration
ii. common emitter configuration
iii. common collector configuration
In common base configuration, input is applied between emitter and base & output is
taken from collector and base as shown in fig.

CHARACTERISTICS OF A COMMON BASE CONFIGURATION: -

The complete electrical behavior of a transistor can be described by specifying the
interrelation of the various currents and voltages. The most important characteristics are input and
output characteristics
INPUT CHARACTERISTIC: It is given by the graph between emitter current I E and emitter-
base voltage VEB at constant collector – base voltage VCB.
Input resistance, ri = ΔVEB /ΔIE at a constant VCB
OUTPUT CHARACTERISTIC: It is the graph between collector current IC and collector base
voltage VCB at constant emitter current IE
output resistance, r0 = ΔVCB /Δ Ic at constant IE
PROPERTIES:
i) Input resistance is small (10 Ω- 100 Ω)
ii) Output resistance is high (1 M Ω)
D IC
iii) α = at constant VCB (Current gain) is low
D IE

iv) Highest voltage gain

v) Moderate power gain
vi) CB amplifier can be designed without self-bias circuit
APPLICATIONS:
I) To provide voltage gain without any current gain
II) For impedance matching in high frequency applications
DISADVANTAGES:
Because of low input resistance loading effects are high.

BTech Data Science 2024 Page -19

Savitribai Phule Pune University Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY

CIRCUIT DIAGRAM:

PROCEDURE: -

Input characteristics:
1. Connect the circuit according to the circuit diagram of input characteristics
2. Keep (Collector to Base Voltage) VCB=0V) by varying VCC (collector supply voltage).
Increasing VEE (Emitter supply Voltage from 0 onwards (0.1V, 0.2V….0.75V) observe
IE (Emitter current for different values of VEB (Emitter to Base voltage).
3. Repeat Step 2 for Different (collector to Base voltage) VCB i.e. 3V & 6V.
4. Tabulate the results in the tabular column and plot the graph.

Output characteristics:
1. Connect the circuit according to the circuit diagram of output characteristics.
2. Keep (collector supply voltage) VCC=0V. Increase (Emitter supply Voltage) VEE to get
Emitter current IE= 3mA.

3. Now increase (Collector supply voltage) VCC from 0 onwards and observe the Collector
current IC for different Values of (Collector to Base voltage) VCB Without exceeding the
rated value (IC=15mA)
4. Tabulate the results in the tabular column and plot the graph.

Department of Technology Page -20

Savitribai Phule Pune University Basics of Electronics (BTDS103)
DODEPARTMENT OF TECHNOLOGY

OBSERVATIONS:

INPUT CHARACTERISTICS:

APPLIED VCB=0V VCB=1V VCB=2V

VOLTAGE
VEB(V) IE(mA) VEB(V) IE(mA) VEB(V) IE(mA)

0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
2
3
4
5

Department of Technology Page -21

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
OUTPUT CHARACTERISTICS:

IE=10mA IE=20mA IE=30mA

S.No VCB(V) IC(mA) VCB(V) IC(mA) VCB(V) IC(mA)
0
1
2
3
4
5
6
7
8
9
10

MODEL GRAPHS:1

INPUT CHARACTE2.1RISTICS

OUTPUT CHARACTERISTICS

BTech Data Science 2024 Page -22

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY

Precautions:
1. Always keep the supply Voltage Knobs i.e. VEB, VCB positions at minimum position when
switching on & off .
2. Never load the meters above its rated range.
3. Avoid loose connections at the junction.

RESULT: -

BTech Data Science 2024 Page -23

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:

1. What is bipolar junction transistor?

2. Define current amplification factor?
3. What are the different configurations of BJT?
4. Give the major applications of transistor?
5. What are the uses of CB configuration?
6. What is the range of α for the transistor?
7. Draw the input and output characteristics of the transistor in CB
Configuration?
8. What is the relation between α and β?
9. What are the input and output impedances of CB configuration?
10. Identify various regions in output characteristics?
11. Define α (alpha)?
12. Draw diagram of CB configuration for PNP transistor?
13. What is EARLY effect?
14. What is the power gain of CB configuration?
15. What is stability factor and thermal runaway?
16. What is bipolar junction transistor?
17. Define current amplification factor?
18. What are the different configurations of BJT?
19. Give the major applications of transistor?
20. What are the uses of CB configuration?
21. What is the range of α for the transistor?
22. Draw the input and output characteristics of the transistor in CB
Configuration?
23. What is the relation between α and β?
24. What are the input and output impedances of CB configuration?
25. Identify various regions in output characteristics?
26. Define α (alpha)?
27. Draw diagram of CB configuration for PNP transistor?
28. What is EARLY effect?

BTech Data Science 2024 Page -24

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
29. What is the power gain of CB configuration?
30. What is stability factor and thermal runaway?

Design Problems
1. Input & output characteristics of transistor in CB configuration with RI = 5K.
2. Input & output characteristics of transistor in CB configuration with RO = 2K.
3. Input & output characteristics of transistor in CB configuration with RI = 5K, RO = 2K.
4. Input & output characteristics of Ge transistor in CB configuration with RI = 5K.
5. Input & output characteristics of Ge transistor in CB configuration with RO = 2K.
6. Input & output characteristics of PNP transistor in CB configuration with RI = 5K.
7. Input & output characteristics of PNP transistor in CB configuration with RO = 2K.
8. I/p & O/p characteristics of PNP transistor in CB configuration with RI = 5K, RO = 2K.
9. Input & output characteristics of PNP Ge transistor in CB configuration with RI = 5K.
10. Input & output characteristics of PNP Ge transistor in CB configuration with RO = 2K.
11. Find input Resistance of CB configuration for given transistor
12. Find output conductance of CB configuration for given transistor
13. Find current gain of CB configuration for given transistor
14. Find Voltage gain of CB configuration for given transistor
15. Find Reverse Voltage gain of CB configuration for given transistor
16. Find output Resistance of CB configuration for given transistor
17. Input & output characteristics of transistor in CB configuration with RI = 5K.
18. Input & output characteristics of transistor in CB configuration with RO = 2K.
19. Input & output characteristics of transistor in CB configuration with RI = 5K, RO = 2K.
20. Input & output characteristics of Ge transistor in CB configuration with RI = 5K.
21. Input & output characteristics of Ge transistor in CB configuration with RO = 2K.
22. Input & output characteristics of PNP transistor in CB configuration with RI = 5K.
23. Input & output characteristics of PNP transistor in CB configuration with RO = 2K.
24. I/p & O/p characteristics of PNP transistor in CB configuration with RI = 5K, RO = 2K.
25. Input & output characteristics of PNP Ge transistor in CB configuration with RI = 5K.
26. Input & output characteristics of PNP Ge transistor in CB configuration with RO = 2K.
27. Find input Resistance of CB configuration for given transistor

BTech Data Science 2024 Page -25

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
28. Find the output conductance of CB configuration for a given transistor
29. Find the current gain of CB configuration for a given transistor
30. Find t h e Voltage gain of t h e CB configuration for a given transistor

REALTIME APPLICATIONS:

1. This arrangement is not very common in low-frequency discrete circuits, where it is usually
employed for amplifiers that require an unusually low input impedance, for example to act
as a preamplifier for moving-coil microphones. However, it is popular in integrated circuits
and in high-frequency amplifiers, for example for VHF and UHF, because its input
capacitance does not suffer from the Miller effect, which degrades the bandwidth of the
common emitter configuration, and because of the relatively high isolation between the
input and output. This high isolation means that there is little feedback from the output
back to the input, leading to high stability.

2. This configuration is also useful as a current buffer since it has a current gain of
approximately unity (see formulas below). Often a common base is used in this manner,
preceded by a common emitter stage. The combination of these two form the
cascade configuration, which possesses several of the benefits of each configuration, such
as high input impedance and isolation.

BTech Data Science 2024 Page -26

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 4.

INPUT & OUTPUT CHARACTERISTICS OF TRANSISTOR IN COMMON EMITTER

CONFIGURATION

AIM: -
1. To study the input and output characteristics of transistor (BJT) connected in common
Emitter configuration
2. To calculate current gain β.
3. To calculate input resistance Ri & output resistance Ro.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. Regulated DC supply voltage(RPS) 0-30V 1
2. Voltmeter 0-1V or 0-10v,0-20V 1
3. Ammeter 0-10mA,200mA 1
4. Connecting wires & bread board
5 Transistor BC 107 or 2n2222 or BC547 NPN 1
6 Resistor 1K,100K 1

THEORY:

A transistor is a three-terminal device. The terminals are emitter, base, collector. In

common emitter configuration, input voltage is applied between base and emitter terminals and
output is taken across the collector and emitter terminals. Therefore, the emitter terminal is
common to both input and output. The input characteristics resemble that of a forward biased diode
curve. This is expected since the Base-Emitter junction of the transistor is forward biased. As
compared to CB arrangement IB increases less rapidly with VBE. Therefore, input resistance of
CE circuit is higher than that of CB circuit. The output characteristics are drawn between Ic and
VCE at constant IB. the collector current varies with VCE unto few volts only. After this the
collector
current becomes almost constant, and independent of VCE. The value of VCE up to which the
collector current changes with V CE is known as Knee voltage. The transistor always operated in
the region above Knee voltage, IC is always constant and is approximately equal to IB.

BTech Data Science 2024 Page -27

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
The current amplification factor of CE configuration is given byΒ = ΔIC/ΔIB.

CIRCUIT DIAGRAM:

PROCEDURE: -

Input characteristics:
5. Connect the circuit according to the circuit diagram of input characteristics
6. Keep (Collector to Emitter Voltage) VCE=0V) by varying VCC (collector supply
voltage). Increasing VBB (Base supply Voltage from 0 onwards (0.1V, 0.2V….0.75V)
observe IB (Base current) for different values of VBE (Base to Emitter voltage).
7. Repeat the Step 2 for Different (collector to Emitter voltage) VCE i.e. 3V & 6V.
8. Tabulate the results in the tabular form and plot the graph.
Output characteristics:
5. Connect the circuit according to the circuit diagram of output characteristic.
6. Keep (collector supply voltage) VCC=0V. Increase (Base supply Voltage) VBB to get
Base current IB= 3µA.

BTech Data Science 2024 Page -28

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
7. Now increase (Collector supply voltage) VCC from 0 onwards and observe the Collector
current IC for different Values of (Collector to Emitter voltage ) VCE Without exceeding
the rated value (IC=15mA)
8. Tabulate the results in the tabular column and plot the graph.

OBSERVATIONS:

INPUT CHARACTERISTICS:

APPLIED VCE = 2V VCE = 4V VCE = 6V

VOLTAGE VBE(V) IB(μA) VBE(V) IB(μA) VBE(V) IB(μA)
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1

OUT PUT CHAREACTARISTICS:

IB = 50μA IB = 40μA IB = 70 μA
S.NO VCE(V) IC(mA) VCE(V) ICmA) VCE(V) IC(mA)

BTech Data Science 2024 Page -29

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
MODEL GRAPHS:

INPUT CHARACTERSTICS:

OUTPUT CHARECTERSTICS:

Precautions:
1. Always keep the supply Voltage Knobs i.e. VCE, VBE positions at minimum position when
switching on & off .
2. Never load the meters above its rated range.
3. Avoid loose connections at the junction.

BTech Data Science 2024 Page -30

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
RESULT: -

VIVA QUESTIONS:
1. What is the range of β for the transistor?
2. What are the input and output impedances of CE configuration?
3. Identify various regions in the output characteristics?
4. What is the relation between α and β?
5. Define current gain in CE configuration?
6. Why CE configuration is preferred for amplification?
7. What is the phase relation between input and output?
8. Draw diagram of CE configuration for PNP transistor?
9. What is the power gain of CE configuration?
10. What are the applications of CE configuration? . What is the range of β for the transistor?
2. What are the input and output impedances of CE configuration?
3. Identify various regions in the output characteristics?
4. What is the relation between α and β?
5. Define current gain in CE configuration?
6. Why CE configuration is preferred for amplification?
7. What is the phase relation between input and output?
8. Draw diagram of CE configuration for PNP transistor?
9. What is the power gain of CE configuration?
10. What are the applications of CE configuration?
11. What is the range of β for the transistor?
12. What are the input and output impedances of CE configuration?
13. Identify various regions in the output characteristics?
14. What is the relation between α and β?
15. Define current gain in CE configuration?
16. Why CE configuration is preferred for amplification?
17. What is the phase relation between input and output?

BTech Data Science 2024 Page -31

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
18. Draw a diagram of the CE configuration for the PNP transistor?
19. What is the power gain of CE configuration?
20. What are the applications of CE configuration?
21. What is Early Effect?
22. Why the doping of the collector is less compared to the emitter?
23. What do you mean by ―reverse active‖?
24. What is the difference between CE and Emitter follower circuit?
25. What are the input and output impedances of CE configuration?
26. Identify various regions in the output characteristics.
27. What is the relation between α, β and γ?
28. Define current gain in CE configuration.
29. Why CE configuration is preferred for amplification?
30. What is the phase relation between input and output?
Design Problems
1. Input & output characteristics of BC 107 transistor in CE configuration with RI = 50K.
2. Input & output characteristics of BC 107 transistor in CE configuration with RO = 2K.
3. I/O characteristics of BC 107 transistor in CE configuration with RI = 50K RO = 2K
4. Input & output characteristics of BC 107 transistor in CE configuration with RI = 150K.
5. I/O characteristics of BC 107 transistor in CE configuration with RI = 150K RO = 2K
6. Input & output characteristics of SL 100 transistor in CE configuration with RI = 50K.
7. Input & output characteristics of SL 100 transistor in CE configuration with RO = 2K.
8. I/O characteristics of PNP transistor in CE configuration with RI = 50K RO = 2K
9. Input & output characteristics of PNP transistor in CE configuration with RI = 150K.
10. I/O characteristics of PNP transistor in CE configuration with RI = 150K RO = 2K
11. Input & output characteristics of BC 107 transistor in CE configuration with RI = 50K.
12. Input & output characteristics of BC 107 transistor in CE configuration with RO = 2K.
13. I/O characteristics of BC 107 transistor in CE configuration with RI = 50K RO = 2K
14. Input & output characteristics of BC 107 transistor in CE configuration with RI = 150K.
15. I/O characteristics of BC 107 transistor in CE configuration with RI = 150K RO = 2K
16. Input & output characteristics of SL 100 transistor in CE configuration with RI = 50K.
17. Input & output characteristics of SL 100 transistor in CE configuration with RO = 2K.

BTech Data Science 2024 Page -32

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
18. I/O characteristics of PNP transistor in CE configuration with RI = 50K RO = 2K
19. Input & output characteristics of PNP transistor in CE configuration with RI = 150K.
20. I/O characteristics of PNP transistor in CE configuration with RI = 150K RO = 2K
21. Input & output characteristics of BC 107 transistor in CE configuration with RI = 50K.
22. Input & output characteristics of BC 107 transistor in CE configuration with RO = 2K.
23. I/O characteristics of BC 107 transistor in CE configuration with RI = 50K RO = 2K
24. Input & output characteristics of BC 107 transistor in CE configuration with RI = 150K.
25. I/O characteristics of BC 107 transistor in CE configuration with RI = 150K RO = 2K
26. Input & output characteristics of SL 100 transistor in CE configuration with RI = 50K.
27. Input & output characteristics of SL 100 transistor in CE configuration with RO = 2K.
28. I/O characteristics of PNP transistor in CE configuration with RI = 50K RO = 2K
29. Input & output characteristics of PNP transistor in CE configuration with RI = 150K.
30. I/O characteristics of PNP transistor in CE configuration with RI = 150K RO = 2K

REALTIME APPLICATIONS:
Common-emitter amplifiers are also used in radio frequency circuits, for example, to amplify
faint signals received by an antenna. In this case, it is common to replace the load resistor with a tuned
circuit. This may be done to limit the bandwidth to a narrow band centered around the intended
operating frequency. More importantly, it also allows the circuit to operate at higher frequencies as the
tuned circuit can be used to resonate any inter-electrode and stray capacitances, which normally limit
the frequency response. Common emitters are also commonly used as low-noise amplifiers.

BTech Data Science 2024 Page -33

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 5.

HALF WAVE RECTIFIR WITH & WITHOUT FILTER.

AIM: -

1. To find ripple factor & regulation for Half wave rectifier.

2. To examine the input and output waveforms..

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. Transformer 6-0-6V or 9-0-9V 1
2. Diode In4007, 1
3. Resistors or DRB 1k,4.7k,10k,22K,100k 1each
4. Connecting wires & breadboard

THEORY: -

During positive half-cycle of the input voltage, the diode D1 is in forward bias and conducts
through the load resistor R1. Hence the current produces an output voltage across the load resistor
R1, which has the same shape as the +ve half cycle of the input voltage. During the negative half-
cycle of the input voltage, the diode is reverse biased and there is no current through the circuit.
i.e., the voltage across R1 is zero. The net result is that only the +ve half cycle of the input voltage
appears across the load. The average value of the half wave rectified o/p voltage is the value
measured on the dc voltmeter. For practical circuits, transformer coupling is usually provided for
two reasons.
1. The voltage can be stepped up or stepped-down, as needed.
2. The AC source is electrically isolated from the rectifier. Thus preventing shock hazards in the
secondary circuit.

BTech Data Science 2024 Page -34

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
CIRCUIT DIAGRAM:

PROCEDURE: -

Without filter:
1. Connect the circuit as shown in the circuit diagram.
2. Note down the voltage across the secondary transformer and across the output terminals
(VO) i.e., across load resistor RL (with 1K, 4.7K, 10K, 100k) using DRB Decade
resistance box or discrete component.
3. Vary the RL load resistor for different values note down AC and DC voltages across the
RL using DMM or CRO.
4. Now Disconnect the RL and note the No Load voltage VNL.
5. Calculate the ripple factor & regulation using the formula for different loads and tabulate.

With filter:

1. Connect a capacitor (100µf/35V) across the load resistance RL.

2. Note down the voltage across the secondary transformer and across the output
terminals (Vo) i.e., across load resistor RL (with 1K, 4.7K, 10K, 100k) using
DRB Decade resistance box or discrete component.
3. Vary the RL load resistor for different values note down AC and DC voltages across
the RL using DMM or CRO.
4. Now Disconnect the RL and note the No Load voltage VNL.
Calculate the ripple factor & regulation using formula for different loads and

BTech Data Science 2024 Page -35

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
OBSERVATIONS:

WITHOUT FILTER

SL Ripple factor=Vac/Vdc Idc(Ma)

No RL (Ohm) VFL=Vdc Vac

1 1K
2 2K
3 3K
4 4K
5 5K

Were % of regulation =VNL-VFL/VFL*100=

[VNL= No load voltage
VFL= Full load voltage]

WITH FILTER

SL Ripple factor=Vac/Vdc Idc(Ma)

No RL (Ohm) VFL=Vdc Vac

1 1K
2 2K
3 3K
4 4K
5 5K

Were % of regulation =VNL-VFL/VFL*100=

[VNL= No load voltage
VFL= Full load voltage]

BTech Data Science 2024 Page -36

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
Theoretical calculations for Ripple factor:-

Without Filter:-
Vrms=Vm/2
Vm=2Vrms
Vdc=Vm/П
Ripple factor r=√ (Vrms/ Vdc )2 -1 =
With Filter:-
Ripple factor, r=1/ (2√3 f C R)
Where f =50Hz
C =100µF
RL=1KΩ

PRECAUTIONS:
1. The primary and secondary sides of the transformer should be carefully identified.
2. The polarities of the diode & capacitor should be carefully connected.
3. While determining the % regulation, first Full load should be applied and then it should be
decremented in steps.
4. Avoid loose contact.
5. CRO must be handled carefully. Use CH1 for input and CH2 for output signal.

RESULT:-

BTech Data Science 2024 Page -37

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:

1. What is the PIV of Half wave rectifier?

2. What is the efficiency of a wave rectifier?
3. What is the rectifier?
4. What is the difference between the half-wave rectifier and the full-wave rectifier?
5. What is the o/p frequency of the Bridge Rectifier?
6. What are the ripples?
7. What is the function of the filters?
8. What is TUF?
9. What is the average value of o/p voltage for HWR?
10. What is the peak factor?
11. What is the PIV of Half wave rectifier?
12. What is the efficiency of a wave rectifier?
13. What is the rectifier?
14. What is the difference between the half-wave rectifier and the full wave rectifier?
15. What is the o/p frequency of the Bridge Rectifier?
16. What are the ripples?
17. What is the function of the filters?
18. What is TUF?
19. What is the average value of o/p voltage for HWR?
20. What is the peak factor?
21. What is the PIV of Half wave rectifier?
22. What is the efficiency of a wave rectifier?
23. What is the rectifier?
24. What is the difference between the half-wave rectifier and full-wave rectifier?
25. What is the o/p frequency of the Bridge Rectifier?
26. What are the ripples?
27. What is the function of the filters?
28. What is TUF?
29. What is the average value of o/p voltage for HWR?
30. What is the peak factor?

BTech Data Science 2024 Page -38

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
Design Problems
1. Examine the I/O waveforms of HWR without filter RL = 2K
2. Examine the I/O waveforms of HWR without filter RL = 4.5K
3. Examine the I/O waveforms of HWR without filter RL = 2K using Ge diode.
4. Examine the I/O waveforms of HWR without filter RL = 4.5K using Ge diode.
5. Examine the I/O waveforms of HWR without filter RL = 2K, change the diode location.
6. Examine the I/O waveforms of HWR without filter RL = 4.5K invert diode.
7. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF
8. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF
9. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF using Ge diode.
10. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF, invert diode.
11. Examine the I/O waveforms of HWR without filter RL = 2K
12. Examine the I/O waveforms of HWR without filter RL = 4.5K
13. Examine the I/O waveforms of HWR without filter RL = 2K using Ge diode.
14. Examine the I/O waveforms of HWR without filter RL = 4.5K using Ge diode.
15. Examine the I/O waveforms of HWR without filter RL = 2K, change the diode location.
16. Examine the I/O waveforms of HWR without filter RL = 4.5K invert diode.
17. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF
18. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF
19. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF using Ge diode.
20. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF, invert diode.
21. Examine the I/O waveforms of HWR without filter RL = 2K
22. Examine the I/O waveforms of HWR without filter RL = 4.5K
23. Examine the I/O waveforms of HWR without filter RL = 2K using Ge diode.
24. Examine the I/O waveforms of HWR without filter RL = 4.5K using Ge diode.
25. Examine the I/O waveforms of HWR without filter RL = 2K, change the diode location.
26. Examine the I/O waveforms of HWR without filter RL = 4.5K invert diode.
27. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF
28. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF
29. Examine the I/O waveforms of HWR with filter RL = 2K, C = 0.047 µF using Ge diode.
30. Examine the I/O waveforms of HWR with filter RL = 5K, C = 0.1 µF, invert diode.

BTech Data Science 2024 Page -39

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
REALTIME APPLICATIONS:

1. The primary application of rectifiers is to derive DC power from an AC supply (AC to DC

converter). Virtually all electronic devices require DC, so rectifiers are used inside the power
supplies of virtually all electronic equipment.

2. Converting DC power from one voltage to another is much more complicated. One method of DC-
to-DC conversion first converts power to AC (using a device called an inverter), then uses a
transformer to change the voltage, and finally rectifies power back to DC. A frequency of typically
several tens of kilohertz is used, as this requires much smaller inductance than at lower frequencies
and obviates the use of heavy, bulky, and expensive iron-cored units.

Output voltage of a full-wave rectifier with controlled thyristors

3. Rectifiers are also used for the detection of amplitude-modulated radio signals. The signal may be
amplified before detection. If not, a very low voltage drop diode or a diode biased with a fixed
voltage must be used. When using a rectifier for demodulation the capacitor and load resistance must
be carefully matched: too low a capacitance makes the high-frequency carrier pass to the output, and
too high makes the capacitor just charge and stay charged.

4. Rectifiers supply polarised voltage for welding. In such circuits control of the output current is
required; this is sometimes achieved by replacing some of the diodes in a bridge
rectifier with thyristors, effectively diodes whose voltage output can be regulated by switching on
and off with phase-fired controllers.

BTech Data Science 2024 Page -40

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 6.

FULL WAVE RECTIFIR WITH & WITHOUT FILTER.

AIM: -

1. To find ripple factor & regulation for full wave rectifier.

2. To examine the input and output waveforms..

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. Transformer 6-0-6V or 9-0-9V 1
2. Diode In4007 2 or 4
3. Resistors 1k,2.2k,3.3k,4.7K,10k 1each
4. Connecting wires & bread board

THEORY:-
The circuit of a center-tapped full wave rectifier uses two diodes D1&D2. During positive
half cycle of secondary voltage (input voltage), the diode D1 is forward biased and D2is reverse
biased. The diode D1 conducts and current flows through load resistor RL.
During negative half cycle, diode D2 becomes forward biased and D1 reverse biased. Now, D2
conducts and current flows through the load resistor RL in the same direction. There is a
continuous current flow through the load resistor RL, during both the half cycles and will get
unidirectional current as show in the model graph. The difference between full wave and half wave
rectification is that a full wave rectifier allows unidirectional (one way) current to the load during
the entire 360 degrees of the input signal and half-wave rectifier allows this only during one half
cycle (180 degree)

BTech Data Science 2024 Page -41

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
CIRCUIT DIAGRAM:

PROCEDURE: -

Without filter:
1. Connect the circuit as shown in the circuit diagram.
2. Note down the voltage across the secondary of transformer and across the output
terminals (Vo) i.e. across load resistor RL (with 1K, 4.7K, 10K, 100k) use DRB Decade
resistance box or discrete component.
2. Vary the RL load resistor for different values note down AC and DC voltages across
the RL using DMM or CRO.
4. Now Disconnect the RL and note the No Load voltage VNL.

BTech Data Science 2024 Page -42

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
5. Calculate the ripple factor & regulation using formula for different loads and tabulate.

With filter:

1. Connect a capacitor (100µf/35V) across the load resistance RL..

2. Note down the voltage across the secondary of transformer and across the output
terminals (Vo) i.e. across load resistor RL (with 1K, 4.7K, 10K, 100k) use DRB
Decade resistance box or discrete component.
3. Vary the RL load resistor for different values note down AC and DC voltages across
the RL using DMM or CRO.
4. Now Disconnect the RL and note the No Load voltage VNL.
5. Calculate the ripple factor & regulation using formula for different loads and tabulate.

OBSERVATIONS:

VNL= ---------- volts

WITHOUT FILTER

SL Ripple factor=Vac/Vdc Idc(Ma)

No RL (Ohm) VFL=Vdc Vac

1 1K
2 2K
3 3K
4 4K
5 5K

Were % of regulation =VNL-VFL/VFL*100=3.378%

[VNL= No load voltage
VFL= Full load voltage]

BTech Data Science 2024 Page -43

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
WITH FILTER

SL Ripple factor=Vac/Vdc Idc(Ma)

No RL (Ohm) VFL=Vdc Vac

1 1K
2 2K
3 3K
4 4K
5 5K

Were % of regulation =VNL-VFL/VFL*100=11.65%

[VNL= No load voltage
VFL= Full load voltage]

THEORETICAL CALCULATIONS:-

Vrms = Vm/ √2

Vm =Vrms√2

Vdc=2Vm/П

(i) Without filter:

Ripple factor, r = √ ( Vrms/ Vdc )2 -1 =

(ii) With filter:

Ripple factor, r = 1/ (4√3 f C RL) where f =50Hz

C =100µF

RL=1KΩ

RESULT:

BTech Data Science 2024 Page -44

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:-
1. Define the regulation of the full wave rectifier.
2. Define peak inverse voltage (PIV). And write its value for the Full-wav rectifier?
3. If one of the diode is changed in its polarities what wave form would you? get?
4. Does the process of rectification alter the frequency of the waveform?
5. What is ripple factor of the Full-wave rectifier?
6. What is the necessity of the transformer in the rectifier circuit?
7. What are the applications of a rectifier?
8. What is meant by ripple and define Ripple factor?
9. Explain how capacitor helps to improve the ripple factor?
10. Define regulation of the full wave rectifier?
11. Define peak inverse voltage (PIV)? And write its value for Full-wave rectifier?
12. If one of the diode is changed in its polarities what wave form would you? get?
13. Does the process of rectification alter the frequency of the waveform?
14. What is ripple factor of the Full-wave rectifier?
15. What is the necessity of the transformer in the rectifier circuit?
16. What are the applications of a rectifier?
17. What is meant by ripple and define Ripple factor?
18. Explain how capacitor helps to improve the ripple factor?
19. Define regulation of the full wave rectifier?
20. Define peak inverse voltage (PIV)? And write its value for Full-wave rectifier?
21. If one of the diode is changed in its polarities what wave form would you? get?
22. Does the process of rectification alter the frequency of the waveform?
23. What is ripple factor of the Full-wave rectifier?
24. What is the necessity of the transformer in the rectifier circuit?
25. What are the applications of a rectifier?
26. What is meant by ripple and define Ripple factor?
27. Explain how capacitor helps to improve the ripple factor?
28. What is ripple factor of the Full-wave rectifier?
29. What is the necessity of the transformer in the rectifier circuit?
30. What are the applications of a rectifier?

BTech Data Science 2024 Page -45

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
Design Problems
1. Study the performance of FWR with RL = 2K
2. Study the performance of FWR with RL = 5K
3. Study the performance of FWR with RL = 5K using GE diode.
4. Study the performance of FWR with RL = 5K, invert the diodes.
5. Study the performance of FWR with RL = 5K using GE diode, invert diodes.
6. Study the performance of FWR with filter RL = 10K, C = 0.1 µF
7. Study the performance of FWR with filter RL = 2K, C = 0.047 µF
8. Study the performance of FWR with filter RL = 15K, C = 0.047 µF using Ge diode.
9. Study the performance of FWR with filter RL = 5K, C = 0.1 µF, invert diode.
10. Study the performance of FWR with filter RL = 5K, C = 0.94 µF, invert diode.
11. Compare the efficiency of HWR you have done with the FWR circuit designed with
capacitor filter.
12. Compare the efficiency of HWR you have done with the FWR circuit designed with
inductor filter.
13. Compare the efficiency of FWR circuit designed with inductor filter and Capacitor filter.
14. Compare the performance between HWR with Filter and FWR without filter.
15. Compare between HWR and FWR without filters.
16. Study the performance of FWR with filter RL = 100K, C = 0.1 µF
17. Find the efficiency of the full wave rectifier designed with a CLC Filter
18. Find the ripple factor of the FWR with Capacitor filter
19. Find the ripple factor of the FWR with Inductor filter
20. Study the performance of FWR with filter RL = 50K, C = 0.047 µF.
21. Study the performance of FWR with RL = 2K
22. Study the performance of FWR with RL = 5K
23. Study the performance of FWR with RL = 5K using GE diode.
24. Study the performance of FWR with RL = 5K, invert the diodes.
25. Study the performance of FWR with RL = 5K using GE diode, invert diodes.
26. Study the performance of FWR with filter RL = 10K, C = 0.1 µF
27. Study the performance of FWR with filter RL = 2K, C = 0.047 µF
28. Study the performance of FWR with filter RL = 15K, C = 0.047 µF using Ge diode.

BTech Data Science 2024 Page -46

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
29. Study the performance of FWR with filter RL = 5K, C = 0.1 µF, invert diode.
30. Study the performance of FWR with filter RL = 5K, C = 0.94 µF, invert diode.

REALTIME APPLICATIONS:
1. The full wave rectifier circuit is one that is widely used for power supplies and many other
areas where a full wave rectification is required.

2. The full wave rectifier circuit is used in most rectifier applications because of the advantages
it offers. While it is a little more complicated, this normally outweighs the disadvantages.
However sometimes it may not be optimum or necessary to use a full wave rectifier circuit.

BTech Data Science 2024 Page -47

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY EXPT NO: 7.
FET CHARACTERISTICS
AIM: -

1. To study the Drain and Transfer characteristics of FET

2. To find the Drain resistance Trans-conductance and amplification factor

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2. Voltmeter ,0-20V 2
3. Ammeter 0-10mA or 200mA 1
4. Connecting wires & bread board
5. FET transistor BFW10/11 or BF245A 1
6. Resistor 100Ω,560Ω 1each

Theory:

1. The field-effect transistor (FET) is a transistor that uses an electric field to control the shape and
hence the conductivity of a channel of one type of charge carrier in a semiconductor material. FETs
are unipolar transistors as they involve single-carrier-type operation

2. A FET is a three-terminal device, having the characteristics of high input impedance and
less noise, the Gate to Source junction of the FET s always reverse biased. In response to
small applied voltage from drain to source, the n-type bar acts as sample resistor, and the
drain current increases linearly with VDS. With increase in ID the ohmic voltage drop
between the source and the channel region reverse biases the junction and the conducting
position of the channel begins to remain constant. The VDS at this instant is called ―pinch
of voltage‖.
3. If the gate to source voltage (VGS) is applied in the direction to provide additional reverse
bias, the pinch off voltage ill is decreased. In amplifier application, the FET is always used
in the region beyond the pinch-off.

BTech Data Science 2024 Page -48

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
CIRCUIT DIAGRAM:

PROCEDURE: -

Drain or Static characteristics

1. Connect the circuit according to the circuit diagram as shown in figure.

2. Keep the power supply knob to minimum position.
3. Switch on supply keep the gate to source voltage VGS=0V.
4. Increase the drain supply VDD from 0V onwards in steps.
5. Note down current Id and Drain to source voltage VDS without exceeding the rated
Value.
6. Repeat the above procedure for VGS=-1V, -0.5V
7. Tabulate the results and plot the graph.
Transfer characteristics

1. keeping the same circuit connections bring the Knobs of supply t minimum.
2. Now vary VDS drain to source voltage at 1V by Varying VDD Drain supply voltage.
3. Increasing the gate to source voltage VGS from 0V onwards in suitable steps.
4. Note down the corresponding variation in ID until it becomes 0V.

BTech Data Science 2024 Page -49

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
5. Repeat the above 3 step for VDS=2V & 4V constant
6. Tabulate the results and plot graph.

Tabular column
Drain or Static characteristics
VGS=0V VGS=-1V VGS=-2V

VDS ID VDS ID VDS ID

in volts in mA in volts in mA in volts in mA

BTech Data Science 2024 Page -50

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
Transfer characteristics
VDS=0.5V VDS=-1V VDS=1.5V

VGS ID VGS ID VGS ID

in volts in mA in volts in mA in volts in mA

BTech Data Science 2024 Page -51

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY

MODEL GRAPH:
TRANSFER CHARACTERISTICS

DRAIN CHARACTERISTICS

PRECAUTIONS:
1. Always keep the supply voltage knobs i.e VDD, VGG position at t h e minimum
position when switching on and off
2. Practically FET contains four terminals: source, drain, Gate, and substrate.
3. Source and case should be short-circuited.
4. Voltages exceeding the ratings of the FET should not be applied.

BTech Data Science 2024 Page -52

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
5. Never load the meters above the rated range.
6. Avoid loose contacts at the junction.

RESULT: -

VIVA QUESTIONS:

1. Why FET is called as a unipolar device/

2. Name the terminals of FET.
3. What is the difference between BJT and FET?
4. What are the major applications of FET?
5. What are the advantages of FET?
6. Difference between MOSFET and FET?
7. Give the applications MOSFET.
8. What is the basis configuration of JFET?
9. What are depletion mode and enhance mode?
10. What are trans-conductance and amplification factors?
11. Why FET is called as a unipolar device/
12. Name the terminals of FET.
13. What is the difference between BJT and FET?
14. What are the major applications of FET?
15. What are the advantages of FET?
16. Difference between MOSFET and FET?
17. Give the applications MOSFET.
18. What is the basis configuration of JFET?
19. What are depletion mode and enhance mode?
20. What are trans-conductance and amplification factors?
21. Why FET is called as a unipolar device/
22. Name the terminals of FET.

BTech Data Science 2024 Page -53

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
23. What is the difference between BJT and FET?
24. What are the major applications of FET?
25. What are the advantages of FET?
26. Difference between MOSFET and FET?
27. Give the applications MOSFET.
28. What is the basis configuration of JFET?
29. What are depletion mode and enhance mode?
30. What is the trans-conductance and amplification factor?
Design Problems
1. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω.
2. Study the Drain and Transfer characteristics of BFW 10 with RL = 280 Ω.
3. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω, RL = 280 Ω.
4. Study the Drain and Transfer characteristics of BFW 10 with RI = 200 Ω.
5. Study the Drain and Transfer characteristics of BFW 10 with RL = 1120 Ω.
6. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 50 Ω.
7. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 280 Ω.
8. Study the Drain, and Transfer characteristics of P-JFET BFW 11 with RI = 50 Ω, RL = 280
Ω.
9. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 200 Ω.
10. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 1120 Ω.
11. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω.
12. Study the Drain and Transfer characteristics of BFW 10 with RL = 280 Ω.
13. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω, RL = 280 Ω.
14. Study the Drain and Transfer characteristics of BFW 10 with RI = 200 Ω.
15. Study the Drain and Transfer characteristics of BFW 10 with RL = 1120 Ω.
16. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 50 Ω.
17. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 280 Ω.
18. Study the Drain, and Transfer characteristics of P-JFET BFW 11 with RI = 50 Ω, RL = 280
Ω.
19. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 200 Ω.
20. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 1120 Ω.
21. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω.

BTech Data Science 2024 Page -54

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
22. Study the Drain
DODEPARTMENT and Transfer characteristics of BFW 10 with RL = 280 Ω.
OF TECHNOLOGY

BTech Data Science 2024 Page -55

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
23. Study the Drain and Transfer characteristics of BFW 10 with RI = 50 Ω, RL = 280 Ω.
24. Study the Drain and Transfer characteristics of BFW 10 with RI = 200 Ω.
25. Study the Drain and Transfer characteristics of BFW 10 with RL = 1120 Ω.
26. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 50 Ω.
27. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 280 Ω.
28. Study the Drain, and Transfer characteristics of P-JFET BFW 11 with RI = 50 Ω, RL = 280
Ω.
29. Study the Drain and Transfer characteristics of P channel JFET BFW 11 with RI = 200 Ω.
30. Study the Drain and transfer characteristics of P channel JFET BFW 11 with RL = 1120 Ω.

REALTIME APPLICATIONS:

1. Low Noise Amplifier. Noise is an undesirable disturbance superimposed on a useful

signal. Noise interferes with the information contained in the signal; the greater the noise,
the less the information. For instance, the noise in radio receivers develops crackling and
hissing which sometimes completely masks the voice or music. Similarly, the noise in TV
receivers produces small white or black spots on the picture; a severe noise may wipe out
the picture. Noise is independent of the signal strength because it exists even when the
signal is off.
2. A buffer amplifier is a stage of amplification that isolates the preceding stage from the
following stage. Source follower (common drain) is. Used as a buffer amplifier. Because
of the high input impedance and low output impedance FET acts as an excellent buffer
amplifier, as shown in the figure. Owing to high input impedance almost all the output
voltage of the preceding stage appears at the input of the buffer amplifier and owing to low
output impedance all the output voltage from the buffer amplifier reaches the input of the
following stage, even there may be a small load resistance.

BTech Data Science 2024 Page -56

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY

EXPT NO: 8.

DESIGN OF SELF BIAS CIRCUIT

AIM:To design a self bias circuit and to observe stability by changing β of the transistor.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2. Tansistor With different β values 2
3. Resistor Different According to design 1
4. Bread board
5. Connecting wire
6.

Theory:
Transistor Biasing is the process of setting a transistors DC operating voltage or current
conditions to the correct level so that any AC input signal can be amplified correctly by the
transistor. A transistors steady state of operation depends a great deal on its base current, collector
voltage, and collector current and therefore, if a transistor is to operate as a linear amplifier, it must
be properly biased to have a suitable operating point.
Establishing the correct operating point requires the proper selection of bias resistors and load
resistors to provide the appropriate input current and collector voltage conditions. The correct
biasing point for a, either NPN or PNP, generally lies somewhere between the two extremes of
operation with respect to it being either ―fully-ON‖ or ―fully-OFF‖ along its load line. This
central operating point is called the ―Quiescent Operating Point‖ or Q-point for short.

When a bipolar transistor is biased so that the Q-point is near the middle of its operating
range, that is approximately halfway between cut-off and saturation, it is said to be operating as a
Class-A amplifier. This mode of operation allows the output current to increase and decrease

BTech Data Science 2024 Page -57

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
around the amplifiers Q-point without distortion as the input signal swings through a complete
cycle. In other words, the output current flows for the full 360 o of the input cycle.

So how do we set this Q-point biasing of a transistor? – The correct biasing of the transistor is
achieved using a process know commonly as Base Bias.
One of the most frequently used biasing circuits for a transistor circuit is with the self-bias of the
emitter-bias circuit where one or more biasing resistors are used to set up the initial DC values of
transistor currents, (IB ), ( IC ) and ( IE ).
The two most common forms of transistor biasing are: Beta Dependent and Beta
Independent. Transistor bias voltages are largely dependent on transistor beta, ( β ) so the biasing
set up for one transistor may not necessarily be the same for another transistor. Transistor biasing
can be achieved either by using a single feedback resistor or by using a simple voltage divider
network to provide the required biasing voltage.
The following are five examples of transistor Base bias configurations from a single supply
( Vcc ).
The function of the ―DC Bias level‖ or ―no input signal level‖ is to correctly set the
transistors Q-point by setting its Collector current ( IC ) to a constant and steady state value without
an input signal applied to the transistors Base.

This steady-state or DC operating point is set by the values of the circuits DC supply
voltage ( Vcc ) and the value of the biasing resistors connected the transistors Base terminal.
Since the transistors Base bias currents are steady-state DC currents, the appropriate use of
coupling and bypass capacitors will help block bias current setup for one transistor stage affecting
the bias conditions of the next. Base bias networks can be used for Common-base (CB), common-
collector (CC) or common-emitter (CE) transistor configurations. In this simple transistor biasing
tutorial we will look at the different biasing arrangements available for a Common Emitter
Amplifier
A self bias circuit stabilizes the bias point more appropriately than a fixed bias circuit

BTech Data Science 2024 Page -58

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
CIRCUIT DIAGRAM:

CALCULATIONS:
Given VCC=10V, RE=220 ohm IC=4mA VCE=6V VBE=0.6V hfe=229
RC=(VCC-VCE)/IC
IB=IC/ β
RB= β*RE/10
VBB=IB*RB+VBE +(IB+IC)RE
R1=(VCC/VBB)*RB
R2=RB/(1-VBB/VCC)
PROCEDURE:
1. Assemble the circuit on a bread board with designed values of resistors and transistor.
2. Apply Vcc and measure VCE, VBE and VEE and record the readings in table I.
3. Without changing the values of biasing resistors, change the transistor with other β
values and repeat the above steps and record the readings in the table.
OBSERVATIONS:
β value VCE VBE VEE IC=(VCC-VCE)/RC IE=VEE/RE

RESULT:

BTech Data Science 2024 Page -59

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 9.

FREQUENCY RESPONSE OF COMMON COLLECTOR AMPLIFIER

AIM: -
1. To plot frequency response of CC amplifier and calculate gain & bandwidth.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2 Function generator 1MHz 1
2. Dual trace CRO(oscilloscope) 25MHz 1
3. BJT BC107 OR 2N2222,BC547 1
4. Connecting wires
5. capacitor 10µf=2,100 µf
6. Resistor

THEORY:
A transistor is a three terminal active device. The terminals are emitter, base, collector. In
CB configuration, the base is common to both input (emitter) and output (collector). For normal
operation, the E-B junction is forward biased and C-B junction is reverse biased. In CB
configuration, IE is +ve, IC is –ve and IB is –ve. So, VEB=f1 (VCB,IE) and IC=f2 (VCB,IB) With
an increasing the reverse collector voltage, the space-charge width at the output junction increases
and the effective base width ‗W‘ decreases. This phenomenon is known as ―Early effect‖. Then,
there will be less chance for recombination within the base region. With increase of charge
gradient within the base region, the current of minority carriers injected across the emitter junction
increases.The current amplification factor of CB configuration is given by, α= ΔIC/ ΔIE
In common-collector amplifier the input is given at the base and the output is taken at the
emitter. In this amplifier, there is no phase inversion between input and output. The input
impedance of the CC amplifier is very high and output impedance is low. The voltage gain is less
than unity. Here the collector is at ac ground and the capacitors used must have a negligible

BTech Data Science 2024 Page -60

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
reactance at the frequency of operation. This amplifier is used for impedance matching and as a
buffer amplifier. This circuit is also known as emitter follower.

CIRCUIT DIAGRAM:

PROCEDURE: -

1. Connect the circuit according to the circuit diagram as shown in figure on breadboard.
2. Set the power supply at 12V and function generator signal amplitude (20 to 50mV) for
(sine wave) 1 KHz frequency on CH-1knob to minimum position.
3. FEED the signal sine wave (20 to 50mV) to the input of CE amplifier and observe the Vi
voltage on Ch-1 &output Vo voltage on Ch-2..
4. keeping the input signal unchanged select the range switch (10Hz-1MHz) in steps.
5. Note down the Vo output voltage amplitude for different frequency {15H, 25Hz,
100Hz…1MHz}
6. Tabulate the results in tabular form.
7. After calculation Av and gain in dB using semi-logarithm sheet plot the curve.

BTech Data Science 2024 Page -61

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
WAVEFORM:

OBSERVATIONS:

FREQUENCY RESPONSE: Vi=20mv

SI.NO. FREQUENCY O/PVOLT Av=Vo/Vi GAIN IN Db

(Hz) (Vo) Av=20log 10(Av)

1 100

2 200

3 500

4 1k

5 2k

6 3k

BTech Data Science 2024 Page -62

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
7 4k

8 5k

9 6k

10 7k

11 8k

12 9k

13 10k

14 20k

15 30k

16 40k

17 50k

18 60k

19 70k

20 80k

21 90k

22 100k

23 200k

24 500k

25 1M

BTech Data Science 2024 Page -63

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
PRECAUTIONS:

1. The input voltage must be kept constant while taking frequency response.
2. Proper biasing voltages should be applied.

RESULT:

VIVA QUESTIONS:

1. What are the applications of CC amplifiers?

2. What is the voltage gain of a CC amplifier?
3. What are the values of input and output impedances of the CC amplifier?
4. To which ground the collector terminal is connected in the circuit?
5. Identify the type of biasing used in the circuit?
6. Give the relation between α, β, and γ.
7. Write the other name of the CC amplifier?
8. What are the differences between CE, CB and CC?
9. When compared to CE, CC is not used for amplification. Justify your answer?
10. What is the phase relationship between input and output in CC?
11. What is the type of capacitor used in RC coupled amplifier for a) coupling two phases

12. What is signal source used for the experiment of an RC coupled amplifier and how
much maximum voltage it could give

13. How do you determine AC power output in class A amplifier i.e., do you measure current
or voltage and how?

14. What are the applications of CC amplifier?

BTech Data Science 2024 Page -64

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
15. What is the voltage gain of CC amplifier?
16. What are the values of input and output impedances of the CC amplifier?
17. To which ground the collector terminal is connected in the circuit?
18. Identify the type of biasing used in the circuit?
19. Give the relation between α, β and γ.
20. Write the other name of CC amplifier?
21. What are the differences between CE, CB and CC?
22. When compared to CE, CC is not used for amplification. Justify youranswer?
23. What is the phase relationship between input and output in CC?
24. Give the relation between α, β and γ.
25. Write the other name of CC amplifier?
26. What are the differences between CE, CB and CC?
27. When compared to CE, CC is not used for amplification. Justify youranswer?
28. What is the phase relationship between input and output in CC?
29. What is the type of capacitor used in RC coupled amplifier for a) coupling two phases b) by
pass emitter

30. Give the relation between α, β and γ.

Design Problems
1. Plot the frequency response of CC amplifier with RS = 500 Ω using BC 107.
2. Plot the frequency response of CC amplifier with RE = 940 Ω using BC 107.
3. Plot the frequency response of CC amplifier with RB1 = 50 KΩ using BC 107.
4. Plot the frequency response of CC amplifier with RB2 = 66 KΩ using BC 107.
5. Plot frequency response of CC amplifier triangular I/P with RS = 500 Ω using BC 107.
6. Plot the frequency response of CC amplifier with RE = 940 Ω using PNP Transistor.
7. Plot the frequency response of CC amplifier with RB2 = 66 KΩ using PNP Transistor.
8. Plot the frequency response of CC amplifier with RB1 = 50 KΩ using SL 100.
9. Plot frequency response of CC amplifier triangular I/P with RS = 500 Ω using PNP.
10. Plot frequency response of CC amplifier Square I/P with RS = 500 Ω using BC 107.
11. Plot the frequency response of CC amplifier with RS = 100 Ω using BC 107.
12. Plot the frequency response of CC amplifier with RE = 240 Ω using BC 107.

BTech Data Science 2024 Page -65

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
13. Plot the frequency response of CC amplifier with RB1 = 10 KΩ using BC 107.
14. Plot the frequency response of CC amplifier with RB2 = 60 KΩ using BC 107.
15. Plot frequency response of CC amplifier triangular I/P with RS = 100 Ω using BC 107.
16. Plot the frequency response of CC amplifier with RE = 240 Ω using PNP Transistor.
17. Plot the frequency response of CC amplifier with RB2 = 60 KΩ using PNP Transistor.
18. Plot the frequency response of CC amplifier with RB1 = 10 KΩ using SL 100.
19. Plot frequency response of CC amplifier triangular I/P with RS = 100 Ω using PNP.
20. Plot frequency response of CC amplifier Square I/P with RS = 100 Ω using BC 107.
21. Plot the frequency response of CC amplifier with RS = 500 Ω using BC 107.
22. Plot the frequency response of CC amplifier with RE = 940 Ω using BC 107.
23. Plot the frequency response of CC amplifier with RB1 = 50 KΩ using BC 107.
24. Plot the frequency response of CC amplifier with RB2 = 66 KΩ using BC 107.
25. Plot frequency response of CC amplifier triangular I/P with RS = 500 Ω using BC 107.
26. Plot the frequency response of CC amplifier with RE = 940 Ω using PNP Transistor.
27. Plot the frequency response of CC amplifier with RB2 = 66 KΩ using PNP Transistor.
28. Plot the frequency response of CC amplifier with RB1 = 50 KΩ using SL 100.
29. Plot frequency response of CC amplifier triangular I/P with RS = 500 Ω using PNP.
30. Plot frequency response of CC amplifier Square I/P with RS = 500 Ω using BC 107.

REALTIME APPLICATIONS:

1. The low output impedance allows a source with a large output impedance to drive a
small load impedance; it functions as a voltage buffer. In other words, the circuit has
current gain (which depends largely on the hFE of the transistor) instead of voltage gain.
A small change to the input current results in much larger change in the output current
supplied to the output load.

2. One aspect of buffer action is a transformation of impedances. For example,

the Thévenin resistance of a combination of a voltage follower driven by a voltage
source with high Thévenin resistance is reduced to only the output resistance of the
voltage follower (a small resistance). That resistance reduction makes the combination
a more ideal voltage source. Conversely, a voltage follower inserted

BTech Data Science 2024 Page -66

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
between a small load resistance and a driving stage presents a large load to the driving
stage—an advantage in coupling a voltage signal to a small load.

3. This configuration is commonly used in the output stages of class-B and class- AB
amplifiers. The base circuit is modified to operate the transistor in class-B or AB mode.
In class-A mode, sometimes an active current source is used instead of RE(Fig. 4) to
improve linearity and/or efficiency.

BTech Data Science 2024 Page -67

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 10.

FREQUENCY RESPONSE OF COMMON EMITTER AMPLIFIER

AIM: -
1. To plot the frequency response of the CE amplifier and calculate gain & bandwidth.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2 Function generator 1MHz 1
2. Dual trace CRO(oscilloscope) 25MHz 1
3. BJT BC107 1
4. Connecting wires
5. capacitor 10µf=2,100 µf
6. Resistor 220.Ω,5.6kΩ,22K,1K,10K

THEORY:

The CE amplifier provides high gain & wide frequency response. In this amplifier the
emitter lead is common to both input & output circuits and is grounded. The emitter-base circuit
is forward biased. The collector current is controlled by the base current rather than emitter current.
The input signal is applied to base terminal of the transistor and amplifier output is taken across
collector terminal. A very small change in base current produces a much larger change in collector
current. When +VE half-cycle is fed to the input circuit, it opposes the forward bias of the circuit
which causes the collector current to decrease, it decreases the voltage more –VE. Thus when input
cycle varies through a -VE half-cycle, increases the forward bias of the circuit, which causes the
collector current to increases thus the output signal is common emitter amplifier is in out of phase
with the input signal.

BTech Data Science 2024 Page -68

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University(DOT)
DODEPARTMENT OF TECHNOLOGY
CIRCUIT DIAGRAM:

VCC
5V

R5
R4 1k?
22k? C2

10µF
Q1
R3 C1 CRO output

10k? 10µF
BC107BP R1
V1 1.0k?
50mVpk R6
1kHz 5.6k?
R7 C3
0° 220? 100µF

PROCEDURE: -

1. Connect the circuit according to the circuit diagram as shown in figure on breadboard.
2. Set the power supply at 12V and function generator signal amplitude (20 to 50mV) for
(sine wave) 1 KHz frequency on CH-1knob to minimum position.
3. FEED the signal sine wave (20 to 50mV) to the input of CE amplifier and observe the Vi
voltage on Ch-1 &output Vo voltage on Ch-2..
4. keeping the input signal unchanged select the range switch (10Hz-1MHz) in steps.
5. Note down the Vo output voltage amplitude for different frequency {15H, 25Hz,
100Hz…1MHz}
6. Tabulate the results in tabular form.
7. After calculation Av and gain in dB using semi-logarithm sheet plot the curve.

BTech Data Science 2024 Page -69

Savitribai Phule Pune University Basics of Electronics
DODEPARTMENT OF TECHNOLOGY

TABULAR COLUMN: Input = 20mV

Frequency (in Output Voltage Gain Av=Vo/Vi Gain(in dB) =20log10(Vo/Vi)
Hz) (Vo)
50
100
200
1k
10k
100k
200,400K
1M

MODELWAVE FORMS:

INPUT WAVE FORM:

OUTPUT WAVE FORM

BTech Data Science 2024 Page -70

Savitribai Phule Pune University Basics of Electronics
DODEPARTMENT OF TECHNOLOGY

FREQUENCY RESPONSE

PRECAUTIONS:
1. Avoid loose connections give proper input voltage

RESULT: -
1. Frequency response of BJT amplifier is plotted.
2. Gain = dB (maximum).
3. Bandwidth= fH--fL =

BTech Data Science 2024 Page -71

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:

1. What is phase difference between input and output waveforms of CE amplifier?

2. What type of biasing is used in the given circuit?
3. If the given transistor is replaced by a p-n-p, can we get output or not?
4. What is effect of emitter-bypass capacitor on frequency response?
5. What is the effect of coupling capacitor?
6. What is region of the transistor so that it is operated as an amplifier?
7. How does transistor acts as an amplifier?
8. Draw the h-parameter model of CE amplifier?
9. What type of transistor configuration is used in intermediate stages of a multistage amplifier?
10. What is Early effect?
11. For a common-emitter amplifier, the purpose of the emitter bypass capacitor is
12. For BJT amplifiers, the gain typically ranges from a level just less than 1 to a level
that may exceed 1000.
13. The loaded voltage gain of an amplifier is always more than the no-load level

14. Which of the following configurations has a voltage gain of –RC /re?
15. An emitter-follower amplifier has an input impedance of 107 k . The input signal is 12 . The
approximate output voltage is (common-collector)
16. What is the limit of the efficiency defined by = Po / Pi?
17. What is re equal to in terms of h parameters?

18. What is the controlling current in a common-base configuration?

19. Which of the following techniques can be used in the sinusoidal ac analysis of transistor
networks?
20. The input impedance of a BJT amplifier is purely in nature and can vary from a
few to .
21. A Darlington pair amplifier has
22. What type of biasing is used in the given circuit?
23. If the given transistor is replaced by a p-n-p, can we get output or not?
24. What is effect of emitter-bypass capacitor on frequency response?

BTech Data Science 2024 Page -72

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
25. What is the effect of coupling capacitor?
26. What is region of the transistor so that it is operated as an amplifier?
27. How does transistor acts as an amplifier?
28. Draw the h-parameter model of CE amplifier?
29. What type of transistor configuration is used in intermediate stages of a multistage amplifier?
30. What is Early effect?

Design Problems
1. Plot the frequency response of CE amplifier with 50 mV Triangular I/P using BC 107.
2. Plot frequency response of CE amplifier with 100 mV, RS = 5K Triangular using BC 107.
3. Plot frequency response of CE amplifier with 150 mV, RE = 440 Ω Square using BC 107.
4. Plot the frequency response of CE amplifier with CS = 5 µF using SL 100.
5. Plot the frequency response of CE amplifier with CS = 5 µF using SL 100, VCC = 5V.
6. Plot the frequency response of CE amplifier with RB1 =22K, RB2 =11.2K SL 100,
7. Plot the frequency response of CE amplifier with CE = 200 µF using BC 107.
8. Plot the frequency response of CE amplifier with CS = 5 µF using PNP Transistor.
9. Plot the frequency response of CE amplifier with RB1 =22K, RB2 =11.2K using PNP,
10. Plot the frequency response of CE amplifier with CS = 5 µF using PNP, VCC = 5V.
11. Plot the frequency response of CE amplifier with 10 mV Triangular I/P using BC 107.
12. Plot frequency response of CE amplifier with 10 mV, RS = 5K Triangular using BC 107.
13. Plot frequency response of CE amplifier with 100 mV, RE = 240 Ω Square using BC 107.
14. Plot the frequency response of CE amplifier with CS = 10 µF using SL 100.
15. Plot the frequency response of CE amplifier with CS = 2 µF using SL 100, VCC = 5V.
16. Plot the frequency response of CE amplifier with RB1 =20K, RB2 =11.2K SL 100,
17. Plot the frequency response of CE amplifier with CE = 100 µF using BC 107.
18. Plot the frequency response of CE amplifier with CS = 2 µF using PNP Transistor.
19. Plot the frequency response of CE amplifier with RB1 =20K, RB2 =11.2K using PNP,
20. Plot the frequency response of CE amplifier with CS = 2µF using PNP, VCC = 5V.
21. Plot the frequency response of CE amplifier with 50 mV Triangular I/P using BC 107.
22. Plot frequency response of CE amplifier with 100 mV, RS = 5K Triangular using BC 107.
23. Plot frequency response of CE amplifier with 150 mV, RE = 440 Ω Square using BC 107.
24. Plot the frequency response of CE amplifier with CS = 5 µF using SL 100.
25. Plot the frequency response of CE amplifier with CS = 5 µF using SL 100, VCC = 5V.
26. Plot the frequency response of CE amplifier with RB1 =22K, RB2 =11.2K SL 100,
27. Plot the frequency response of CE amplifier with CE = 200 µF using BC 107.
28. Plot the frequency response of CE amplifier with CS = 5 µF using PNP Transistor.
29. Plot the frequency response of CE amplifier with RB1 =22K, RB2 =11.2K using PNP,
30. Plot the frequency response of CE amplifier with CS = 5 µF using PNP, VCC = 5V.

BTech Data Science 2024 Page -73

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
REALTIME APPLICATIONS:

Common-emitter amplifiers are also used in radio frequency circuits, for example to
amplify faint signals received by an antenna In this case it is common to replace the load resistor
with a tuned circuit. This may be done to limit the bandwidth to a narrow band centered around
the intended operating frequency. More importantly it also allows the circuit to operate at higher
frequencies as the tuned circuit can be used to resonate any inter-electrode and stray capacitances,
which normally limit the frequency response. Common emitters are also commonly used as low-
noise amplifiers.

BTech Data Science 2024 Page -74

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
EXPT NO: 11.

FREQUENCY RESPONSE OF COMMON SOURCE AMPLIFIER

AIM: -
1. To plot frequency response of CS amplifier (common source) and calculate gain &
bandwidth.

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2 Function generator 1MHz 1
2. Dual trace CRO(oscilloscope) 25MHz 1
3. FET BFW10/11 or BF245 1
4. Connecting wires
5. capacitor 10µf=2,100 µf
6. Resistor 1K,4.7K,1M,1K

THEORY:
A field-effect transistor (FET) is a type of transistor commonly used for weak-signal
amplification (for example, for amplifying wireless (signals). The device can amplify analog or
digital signals. It can also switch DC or function as an oscillator. In the FET, current flows along
a semiconductor path called the channel. At one end of the channel, there is an electrode called
the source. At the other end of the channel, there is an electrode called the drain. The physical
diameter of the channel is fixed, but its effective electrical diameter can be varied by the
application of a voltage to a control electrode called the gate. Field-effect transistors exist in two
major classifications. These are known as the junction FET (JFET) and the metal-oxide-
semiconductor FET (MOSFET). The junction FET has a channel consisting of N-type
semiconductor (N channel) or P-type semiconductor (P-channel) material; the gate is made of the
opposite semiconductor type. In P-type material, electric charges are carried mainly in the form
of electron deficiencies called holes. In N-type material, the charge carriers are primarily
electrons. In a JFET, the junction is the boundary between the channel and the gate. Normally,

BTech Data Science 2024 Page -75

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
this P-N junction is reverse-biased (a DC voltage is applied to it) so that no current flows between
the channel and the gate. However, under some conditions there is a small current through the
junction during part of the input signal cycle. The FET has some advantages
and some disadvantages relative to the bipolar transistor. Field-effect transistors are preferred for
weak-signal work, for example in wireless, communications and broadcast receivers. They are also
preferred in circuits and systems requiring high impedance. The FET is not, in general, used for
high-power amplification, such as is required in large wireless communications
and broadcast transmitters. Field-effect transistors are fabricated onto silicon integrated circuit (IC)
chips. A single IC can contain many thousands of FETs, along with other components
such as resistors, capacitors, and diodes.

CIRCUIT DIAGRAM:

VDD
12V

R4
4.7kΩ
C1

Q1 10µF CRO out put

R2 C2

R1
1kΩ 10µF BFW10 1.0kΩ

V1
C3
R3
R5 100µF
50mVrms 470Ω
1kHz 1MΩ
0°

PROCEDURE: -

1. Connect the circuit according to the circuit diagram as shown in figure on breadboard.
2. Set the power supply at 12V and function generator signal amplitude (20 to 50mV) for
(sine wave) 1 KHz frequency on CH-1knob to minimum position.
3. FEED the signal sine wave (20 to 50mV) to the input of CE amplifier and observe the Vi
BTech Data Science 2024 Page -76
 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY

voltage on Ch-1 &output Vo voltage on Ch-2..

4. keeping the input signal unchanged select the range switch (10Hz-1MHz) in steps.

BTech Data Science 2024 Page -77

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
5. Note down the Vo output voltage amplitude for different frequency {15H, 25Hz,
100Hz…1MHz}
6. Tabulate the results in tabular form.
7. After calculation Av and gain in dB using semi-logarithm sheet plot the curve.

PRECAUTIONS:

1. Avoid loose connections and give proper input Voltage

TABULAR COLUMN: Input = 50mV

Frequency (in Hz) Output Voltage (Vo) Gain Av=Vo/Vi Gain(in dB) =20log10(Vo/Vi)

50
100
200
1K
10k
50K,100K
200k
500K
1M

EXPECTED GRAPH:

RESULT: -
1. Frequency response of FET Common source amplifier is plotted.
2. 3 db Gain = dB (maximum).
3. Bandwidth= fH--fL =.

BTech Data Science 2024 Page -78

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
VIVA QUESTIONS:
1. What is Miller effect on common source amplifier?
2. What is the purpose of source resistor and gate resistor?
3. What is swamping resistor
4. What is the purpose of swamping resistor in common source amplifier
5. FET is a liner or non-linear device. And justify your answer
6. What is square law and give an example for a square law device
7. A common-gate amplifier is similar in configuration to which BJT amplifier?
8. The theoretical efficiency of a class D amplifier is
9. A common-source amplifier is similar in configuration to which BJT amplifier?
10. A BJT is a -controlled device.
11. A common-drain amplifier is similar in configuration to which BJT amplifier?
12. For what value of ID is gm equal to 0.5 gm0?
13. Where do you get the level of gm and rd for an FET transistor?
14. The class D amplifier uses what type of transistors?
15. What is the input resistance (Rin(source)) of a common-gate amplifier?
16. Which of the following is a required condition to simplify the equations for Zo and Av for the self-bias
configuration?
17. The steeper the slope of the ID versus VGS curve, the the level of gm

18. What is the typical value for the input impedance Zi for JFETs?
19. MOSFET digital switching is used to produce which digital gates?
20. Which type of FETs can operate with a gate-to-source Q-point value of 0 V?
21. What is Miller effect on common source amplifier?
22. What is the purpose of source resistor and gate resistor?
23. What is swamping resistor
24. What is the purpose of swamping resistor in common source amplifier
25. FET is a liner or non-linear device. And justify your answer
26. What is square law and give an example for a square law device
27. A common-gate amplifier is similar in configuration to which BJT amplifier?
28. The theoretical efficiency of a class D amplifier is
29. A common-source amplifier is similar in configuration to which BJT amplifier?
30. A BJT is a -controlled device.

BTech Data Science 2024 Page -79

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY

Design Problems
1. Plot the frequency and amplitude response of FET BFW 10 amplifier with C1 = 5 µF.
2. Plot the frequency response of FET BFW 10 amplifier with C2 = 5 µF with triangular i/p.
3. Plot the amplitude response of FET BFW 10 amplifier with RG1 = 4.1 K.
4. Plot the amplitude response of FET BFW 10 amplifier with RG2 = 9.4 K triangular i/p.
5. Plot frequency response of BFW 10 amplifier RG1 = 4.1 K, RG2 = 9.4 K with square i/p.
6. Plot the frequency and amplitude response of FET BFW 11 amplifier with C1 = 5 µF.
7. Plot the frequency response of P Channel JFET amplifier with C2 = 5 µF, triangular i/p.
8. Plot the amplitude response of FET BFW 11 amplifier with RG1 = 4.1 K.
9. Plot the amplitude response of P Channel JFET amplifier with RG2 = 9.4 K triangular i/p.
10. Plot frequency response of P Channel JFET RG1 = 4.1 K, RG2 = 9.4 K with square i/p.
11. Plot the frequency and amplitude response of FET BFW 10 amplifier with C1 = 10 µF.
12. Plot the frequency response of FET BFW 10 amplifier with C2 = 2 µF with triangular i/p.
13. Plot the amplitude response of FET BFW 10 amplifier with RG1 = 2.1 K.
14. Plot the amplitude response of FET BFW 10 amplifier with RG2 = 5.4 K triangular i/p.
15. Plot frequency response of BFW 10 amplifier RG1 = 2.1 K, RG2 = 2.4 K with square i/p.
16. Plot the frequency and amplitude response of FET BFW 11 amplifier with C1 = 2 µF.
17. Plot the frequency response of P Channel JFET amplifier with C2 = 2 µF, triangular i/p.
18. Plot the amplitude response of FET BFW 11 amplifier with RG1 = 2.1 K.
19. Plot the amplitude response of P Channel JFET amplifier with RG2 = 2.4 K triangular i/p.
20. Plot frequency response of P Channel JFET RG1 = 2.1 K, RG2 = 9.4 K with square i/p.
21. Plot the frequency and amplitude response of FET BFW 10 amplifier with C1 = 5 µF.
22. Plot the frequency response of FET BFW 10 amplifier with C2 = 5 µF with triangular i/p.
23. Plot the amplitude response of FET BFW 10 amplifier with RG1 = 4.1 K.
24. Plot the amplitude response of FET BFW 10 amplifier with RG2 = 9.4 K triangular i/p.
25. Plot frequency response of BFW 10 amplifier RG1 = 4.1 K, RG2 = 9.4 K with square i/p.
26. Plot the frequency and amplitude response of FET BFW 11 amplifier with C1 = 5 µF.
27. Plot the frequency response of P Channel JFET amplifier with C2 = 5 µF, triangular i/p.
28. Plot the amplitude response of FET BFW 11 amplifier with RG1 = 4.1 K.
29. Plot the amplitude response of P Channel JFET amplifier with RG2 = 9.4 K triangular i/p.
30. Plot frequency response of P Channel JFET RG1 = 4.1 K, RG2 = 9.4 K with square i/p

BTech Data Science 2024 Page -80

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
REALTIME APPLICATIONS:

The common-source (CS) amplifier may be viewed as a transconductance amplifier or as a

voltage amplifier. (See classification of amplifiers). As a transconductance amplifier, the input voltage
is seen as modulating the current going to the load. As a voltage amplifier, input voltage modulates the
amount of current flowing through the FET, changing the voltage across the output resistance
according to Ohm's law. However, the FET device's output resistance typically is not high enough for
a reasonable transconductance amplifier (ideally infinite), nor low enough for a decent voltage
amplifier (ideally zero). Another major drawback is the amplifier's limited high-frequency response.
Therefore, in practice the output often is routed through either a voltage follower (common-drain or
CD stage), or a current follower (common-gate or CG stage), to obtain more favorable output and
frequency characteristics. The CS–CG combination is called a cascode amplifier.

BTech Data Science 2024 Page -81

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY

EXPT NO: 12
SCR CHARACTERISTICS

AIM: -
1. To study the characteristics of SCR

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty

1. (a) Regulated DC supply voltage 0-30V 1
2. Voltmeter ,0-20V 2
3. Ammeter 0-10mA or 200mA 1
4. Connecting wires
5. SCR TYN604 or 616
6. Resistor lK,10K

THEORY:
A silicon-controlled rectifier (or semiconductor-controlled rectifier) is a four-layer
solid state current controlling device. The name "silicon controlled rectifier" is General Electric's
trade name for a type of thyristor. The SCR was developed by a team of power engineers led by
Gordon Hall and commercialized by Frank W. "Bill" Gutzwiller in 1957. The Silicon Control
Rectifier (SCR) consists of four layers of semiconductors, which form NPNP or PNP structures.
It has three junctions, labeled J1, J2, and J3 and three terminals. The anode terminal of an SCR is
connected to the P-Type material of a PNPN structure, and the cathode terminal is connected to
the N-Type layer, while the gate of the Silicon Control Rectifier SCR is connected to the P- Type
material nearest to the cathode. SCRs are unidirectional devices (i.e. can conduct current only in
one direction) as opposed to TRIACs which are bidirectional (i.e. current can flow through them
in either direction). SCRs can be triggered normally only by currents going into the gate as opposed
to TRIACs which can be triggered normally by either a positive or a negative current applied to
its gate electrode.

BTech Data Science 2024 Page -82

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
SCRs are mainly used in devices where the control of high power, possibly coupled with high
voltage, is demanded. Their operation (it can switch large current on and off) makes them suitable
for use in medium to high-voltage AC power control applications, such as lamp dimming,
regulators and motor control. SCRs and similar devices are used for rectification of high power
AC in high-voltage direct current power transmission. They are also used in the control of welding
machines, mainly MTAW (Metal Tungsten Arc Welding) and GTAW (Gas Tungsten Arc
Welding) process.

CIRCUIT DIAGRAM:

PROCEDURE: -

1. Connect the circuit according to the circuit diagram as shown in figure.

2. Keep the power supply knob to minimum position.
3. Set VAA starting from zero gradually until the current begins to rise and the voltage V
suddenly drops to low value.
4. Note the reading V & I just before and immediately after the firing on the SCR.
5. Repeat step 3 for various values of IG say 10mA & 8mA

BTech Data Science 2024 Page -83

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
6. Tabulate the reading in the table. Note down the latching and holding currents from the
plot.

MODEL WAVEFORM:

RESULT:

VIVA QUESTIONS:
1. How many junctions are there in SCR?
2. Name few applications of SCR?
3. Name the types of SCR?
4. IS SCR a unidirectional device?
5. What do you mean by holding current and holding voltage?
6. What is meant by the term break over voltage?
7. What is the usual method of switching off and SCR?
8. What is Thyristor?

BTech Data Science 2024 Page -84

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
9. What are diac and tric?
10. What does latching of an SCR mean?
11. What is asymmetrical SCR?
12. Why is Peak Reverse Voltage Important?
13. What are the applications of SCR?
14. What is the difference between SCR and TRIAC?
15. What is an SCR?
16. What are the difference between transistor and SCR?
17. Explain latching current and holding current of the thyristor
18. What are the advantages of MOSFET‘s over BJT‘s?
19. Why pulsed gate drive is used for SCR?
20. Define the delay angle of phase-controlled rectifier.
21. Why is the power factor of a semi converter better than full converter?
22. What are the differences between a freewheeling diode and a feedback diode?
23. What is inverting operation of the converter?
24. What are control strategies of chopper?
25. Explain the use of step-up chopper.
26. What is four quadrant chopper?
27. Name few applications of SCR?
28. Name the types of SCR?
29. IS SCR a unidirectional device?
30. What do you mean by holding current and holding voltage

Design Problems
1. Plot the volt ampere characteristics of SCR 2N46 with RE = 500 Ω.
2. Plot the volt ampere characteristics of SCR 2N46 with RB2 = 500 Ω.
3. Plot the volt ampere characteristics of SCR 2N46 with RB1 = 940 Ω.
4. Plot the volt ampere characteristics of SCR 2N46 with RE = RB2 = 500 Ω.
5. Plot thevolt ampere characteristics of SCR 2N46 with RE = RB2 = 1 K Ω and RB1 = 500 Ω.
6. Draw the volt ampere characteristics of SCR 2N47 with RE = 500 Ω.
7. Draw the volt ampere characteristics of SCR 2N47 with RB2 = 500 Ω.
8. Draw the volt ampere characteristics of SCR2N47 with RB1 = 940 Ω.

BTech Data Science 2024 Page -85

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
9. Draw the volt ampere characteristics of SCR2N47 with RE = RB2 = 1000 Ω.
10. Draw the volt ampere characteristics of SCR2N47 with RB1 = RB2 = 1 K Ω and RE =0.5K.
11. Plot the volt ampere characteristics of SCR2N46 with RE = 200 Ω.
12. Plot the volt ampere characteristics of SCR 2N46 with RB2 = 200 Ω.
13. Plot the volt ampere characteristics of SCR 2N46 with RB1 = 140 Ω.
14. Plot the volt ampere characteristics of SCR 2N46 with RE = RB2 = 10 Ω.
15. Plot the volt ampere characteristics ofSCR 2N46 with RE = RB2 = 1 K Ω and RB1 = 10 Ω.
16. Draw the volt ampere characteristics of SCR2N47 with RE = 200 Ω.
17. Draw the volt ampere characteristics of SCR 2N47 with RB2 = 200 Ω.
18. Draw the volt ampere characteristics of SCR 2N47 with RB1 = 140 Ω.
19. Draw the volt ampere characteristics of SCR2N47 with RE = RB2 = 100Ω.
20. Draw the volt ampere characteristics of SCR 2N47 with RB1 = RB2 = 1 0 Ω and RE =1K.
21. Plot the volt ampere characteristics of SCR 2N46 with RE = 500 Ω.
22. Plot the volt ampere characteristics of SCR 2N46 with RB2 = 500 Ω.
23. Plot the volt ampere characteristics of SCR 2N46 with RB1 = 940 Ω.
24. Plot the volt ampere characteristics of SCR 2N46 with RE = RB2 = 500 Ω.
25. Plot thevolt ampere characteristics of SCR 2N46 with RE = RB2 = 1 K Ω and RB1 = 500 Ω.
26. Draw the volt ampere characteristics of SCR 2N47 with RE = 500 Ω.
27. Draw the volt ampere characteristics of SCR 2N47 with RB2 = 500 Ω.
28. Draw the volt ampere characteristics of SCR2N47 with RB1 = 940 Ω.
29. Draw the volt ampere characteristics of SCR2N47 with RE = RB2 = 1000 Ω.
30. Draw the volt ampere characteristics of SCR2N47 with RB1 = RB2 = 1 K Ω and RE =0.5K.

REALTIME APPLICATIONS:

SCRs are mainly used in devices where the control of high power, possibly coupled with
high voltage, is demanded. Their operation makes them suitable for use in medium- to high-
voltage AC power control applications, such as lamp dimming, regulators and motor control.

SCRs and similar devices are used for rectification of high-power AC in high-voltage
direct-current power transmission. They are also used in the control of welding machines, mainly
MTAW (metal tungsten arc welding) and GTAW (gas tungsten arc welding) processes.

BTech Data Science 2024 Page -86

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY EXPT NO: 13.
UJT CHARACTERISTICS
AIM: -
To study the characteristics of UJT

EQUIPMENTS & COMPONENTS REQUIRED:

S.No Device Range/Rating Qty
1. (a) Regulated DC supply voltage 0-30V 1
2. Voltmeter ,0-20V 2
3. Ammeter 0-10mA or 200mA 1
4. Connecting wires
5. UJT 2N2646 1
6. Retor 330Ω,470Ω,1k,10k 1each
Theory:

A unijunction transistor (UJT) is a three-lead electronic semiconductor device with only

one junction that acts exclusively as an electrically controlled switch. The UJT is not used as a
linear amplifier. It is used in free-running oscillators, synchronized or triggered oscillators, and
pulse generation circuits at low to moderate frequencies (hundreds of kilohertz). It is widely used
in the triggering circuits for silicon controlled rectifiers. The low cost per unit, combined with its
unique characteristic, have warranted its use in a wide variety of applications like oscillators, pulse
generators, saw-tooth generators, triggering circuits, phase control, timing circuits, and voltage- or
current-regulated supplies. The original unijunction transistor types are now considered obsolete;
but a later multi-layer device, the "programmable unijunction transistor", is still widely available.

The UJT has three terminals: an emitter (E) and two bases (B1 and B2) and so is sometimes
called a "double-base diode". If no potential difference exists between its emitter and either of its
base leads, an extremely small amount of current flows from B 2 to B1. On the other hand, if an
adequately large voltage relative to its base leads, known as the trigger voltage, is applied to its
emitter, then a very large current will flow from its emitter and join the current flowing from B2
to B1, which would create a larger B1 output current.

The base is formed by lightly doped n-type bar of silicon. Two ohmic contacts B1 and B2 are
attached at its ends. The emitter is of p-type and it is heavily doped; this single PN junction gives

BTech Data Science 2024 Page -87

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
the device its name. The resistance between B1 and B2 when the emitter is open-circuit is called
interbase resistance. The emitter junction is usually located closer to base-2 (B2) than base-1
(B1) so that the device is not symmetrical, because symmetrical unit does not provide optimum
electrical characteristics for most of the applications.

CIRCUIT DIAGRAM:

PROCEDURE: -

1. Connect the circuit according to the circuit diagram as shown in figure.

2. Keep the power supply knob to minimum position.
3. Set the VBB voltage at 5V.
4. Vary the VEB voltage and note down the Ie emitter current in the table.
5. Repeat the step 4 for VBB 10v
6. Plot the graph

MODEL GRAPH:

BTech Data Science 2024 Page -88

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT
OBSEVATIONS: OF TECHNOLOGY

S.NO. VBB=2V VBB=4V

VEB(V) VBE(V) IE(mA) VBE(V) IE(mA)

0.2

0.4

0.6

0.8

10

11

12

BTech Data Science 2024 Page -89

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
CALCULATIONS:

VP = ηVBB + VD

η = (VP-VD) / VBB

η = (η1 + η2 + η3) / 3

RESULT:

VIVA QUESTIONS

1. What is the symbol of UJT?

2. Draw the equivalent circuit of UJT?
3. What are the applications of UJT?
4. Formula for the intrinsic standoff ratio?
5. What does it indicates the direction of arrow in the UJT?
6. What is the difference between FET and UJT?
7. Is UJT is used an oscillator? Why?
8. What is the Resistance between B1 and B2 is called as?
9. What is its value of resistance between B1 and B2?
10. Draw the characteristics of UJT?
11. Define latching current?
12. Define holding current ?
13. Define drain resistance?
14. .Define inter-base resistance ?
15. What is amplification factor ?
16. W hat is the other name of UJT?
17. Derive intrinsic standoff ratio?
18. Draw the equivalent circuit of UJT?
19. Write the features of UJT. ?

BTech Data Science 2024 Page -90

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
20. What is the difference between UJT and FET?

21. What is a UJT?

22. What is relaxation oscillator?

23. What are the applications of UJT?

24. What is the symbol of UJT?

25. Draw the equivalent circuit of UJT?
26. What are the applications of UJT?
27. Formula for the intrinsic standoff ratio?
28. What does it indicates the direction of arrow in the UJT?
29. What is the difference between FET and UJT?
30. Is UJT is used an oscillator? Why?
Design Problems
1. Plot the volt ampere characteristics of UJT 2N46 with RE = 500 Ω.
2. Plot the volt ampere characteristics of UJT 2N46 with RB2 = 500 Ω.
3. Plot the volt ampere characteristics of UJT 2N46 with RB1 = 940 Ω.
4. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 500 Ω.
5. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 1 K Ω and RB1 = 500 Ω.
6. Draw the volt ampere characteristics of UJT 2N47 with RE = 500 Ω.
7. Draw the volt ampere characteristics of UJT 2N47 with RB2 = 500 Ω.
8. Draw the volt ampere characteristics of UJT 2N47 with RB1 = 940 Ω.
9. Draw the volt ampere characteristics of UJT 2N47 with RE = RB2 = 1000 Ω.
10. Draw the volt ampere characteristics of UJT 2N47 with RB1 = RB2 = 1 K Ω and RE =0.5K.
11. Plot the volt ampere characteristics of UJT 2N46 with RE = 200 Ω.
12. Plot the volt ampere characteristics of UJT 2N46 with RB2 = 200 Ω.
13. Plot the volt ampere characteristics of UJT 2N46 with RB1 = 140 Ω.
14. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 200 Ω.
15. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 1 0 Ω and RB1 = 200 Ω.
16. Draw the volt ampere characteristics of UJT 2N47 with RE = 200 Ω.
17. Draw the volt ampere characteristics of UJT 2N47 with RB2 = 200 Ω.
18. Draw the volt ampere characteristics of UJT 2N47 with RB1 = 140 Ω.
19. Draw the volt ampere characteristics of UJT 2N47 with RE = RB2 = 200Ω.
20. Draw the volt ampere characteristics of UJT 2N47 with RB1 = RB2 = 1 0 Ω and RE =1K.
21. Plot the volt ampere characteristics of UJT 2N46 with RE = 500 Ω.
22. Plot the volt ampere characteristics of UJT 2N46 with RB2 = 500 Ω.

BTech Data Science 2024 Page -91

 Basics of Electronics (BTDS103)
Savitribai Phule Pune University
DODEPARTMENT OF TECHNOLOGY
23. Plot the volt ampere characteristics of UJT 2N46 with RB1 = 940 Ω.
24. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 500 Ω.
25. Plot the volt ampere characteristics of UJT 2N46 with RE = RB2 = 1 K Ω and RB1 = 500 Ω.
26. Draw the volt ampere characteristics of UJT 2N47 with RE = 500 Ω.
27. Draw the volt ampere characteristics of UJT 2N47 with RB2 = 500 Ω.
28. Draw the volt ampere characteristics of UJT 2N47 with RB1 = 940 Ω.
29. Draw the volt ampere characteristics of UJT 2N47 with RE = RB2 = 1000 Ω.
30. Draw the volt ampere characteristics of UJT 2N47 with RB1 = RB2 = 1 K Ω and RE =0.5K.

REALTIME APPLICATIONS:

Injunction transistor circuits were popular in hobbyist electronics circuits in the 1960s and
1970s because they allowed simple oscillators to be built using just one active device. For example,
they were used for relaxation oscillators in variable-rate strobe lights. Later, as integrated
circuits became more popular, oscillators such as the 555 timer IC became more commonly used.

BTech Data Science 2024 Page -92