CONTROL DEVICES

1. CAB DEVICES

1) The ergonomically designed console box and suspension type seat provide the operator with com-
fort.
2) ELECTRONIC MONITOR SYSTEM
(1) The centralized electronic monitor system allows the status and conditions of the machine to be
monitored at a glance.
(2) It is equipped with a safety warning system for early detection of machine malfunction.

■ CABIN TYPE

Cup holder
Cigar lighter
VOLUME
+

VOLUME
1
-
2
3

Starting switch
HYU
4 NDA
I
5 BAND
AST

TA
SOURCE
RDS

Cluster
Arm rest
Dozer control lever
Horn switch
Switch panel 2

Speaker
Radio & USB player
Safety hammer

RH control lever Seat

Travel lever Switch panel 1

Defroster Engine speed

control lever
Air vent
LH control lever
Boom swing pedal
Washer tank
Travel pedal
Fuse box
PTO pedal
Safety lever
Storage box

R25Z9A3CD11

3-1
 ■ CANOPY TYPE

Beacon lamp
Cup holder
Cigar lighter
Starting switch
Cluster
Arm rest
Dozer control lever
Horn switch

Seat
Switch panel 1
RH control lever Engine speed
control lever
Travel lever
LH control lever
Boom swing pedal
Washer tank
Travel pedal
Fuse box
Double acting pedal
Safety lever
Storage box

R27Z93CD80

3-2
2. CLUSTER (MACHINE SERIAL NO.: ~#0305)

The cluster consists of gauges and lamps as shown below, to warn the operator in case of abnor-
mal machine operation or conditions for the appropriate operation and inspection.
· Gauges : Indicate operating status of the machine.
· Warning lamp : Indicate abnormality of the machine (red).
· Pilot lamp : Indicate operating status of the machine.
※ The monitor installed on this machine does not entirely guarantee the condition of the
machine. Daily inspection should be performed according to chapter 6, Maintenance.
※ When the monitor provides a warning, immediately check the problem and perform the
required action.

Quick clamp warning lamp Overload warning lamp

Preheat pilot lamp Engine oil pressure warning lamp
Air cleaner warning lamp Battery charging warning lamp

Engine coolant temp gauge Service meter Fuel gauge

Engine coolant temp warning lamp Fuel low level warning lamp

R25Z9A3CD01

※ When the quick clamp switch turn ON, the buzzer sound and the quick clamp warning lamp
lights ON.
The quick clamp switch turn OFF, the buzzer stop and the quick clamp warning lamp lights
OFF.

3-3
1) GAUGES AND DISPLAYS
(1) Service meter
① This meter shows the total operation hours of the machine.
② Always ensure the operating condition of the meter during the
machine operation.
Inspect and service the machine based on hours as indicated
in chapter 6, maintenance.
R35Z73CD02

(2) Fuel gauge

① This gauge indicates the amount of fuel in the fuel tank.
② Fill the fuel when the red range or warning lamp ON.
※ If the gauge illuminates the red range or warning lamp
ON even though the machine is on the normal condition,
check the electric device as that can be caused by the poor
connection of electricity or sensor.
Red range
R25Z9A3CD04

(3) Engine coolant temperature gauge

① This gauge indicates the temperature of coolant.
Red
·Red range : Above 110°C (230°F )
range ② When the red range pointed or warning lamp ON, engine
do not abruptly stop but run it at medium speed to allow it to
cool gradually, then stop it.
Check the radiator and engine.
※ If the engine is stopped without cooled down running, the
R25Z9A3CD03
temperature of engine parts will rise suddenly, this could
cause severe engine trouble.

3-4
2) WARNING AND PILOT LAMPS
(1) Fuel low level warning lamp
① This lamp blinks when the level of fuel is below 8.5ℓ(2.2 U.S.
gal).
② Fill the fuel immediately when the lamp blinks.

R5573CD10

(2) Engine coolant temperature warning lamp

① This lamp blinks when the temperature of coolant is over the
normal temperature 110°C (230°F ) .
② Check the cooling system when the lamp blinks.

R25Z9A3CD08

(3) Engine oil pressure warning lamp

① This lamp blinks after starting the engine because of the low oil
pressure.
② If the lamp blinks during engine operation, shut OFF engine
immediately. Check oil level.

R25Z9A3CD09

(4) Air cleaner warning lamp

① This lamp blinks when the filter of air cleaner is clogged.
② Check the filter and clean or replace it.

R25Z9A3CD20

(5) Battery charging warning lamp

① This lamp blinks when the starting switch is ON, it is turned
OFF after starting the engine.
② Check the battery charging circuit when this lamp blinks during
engine operation.

R25Z9A3CD21

3-5
(6) Preheat pilot lamp
① This lamp lights ON when start switch is turned clockwise to
the ON position.
② When the lamp goes out the operator should start cranking the
engine.
※ Refer to page 4-4.
R25Z9A3CD22

(7) Quick clamp warning lamp

① When the quick clamp switch turned ON, this lamp turn ON
and the buzzer sounds.
② This lamp turned OFF and the buzzer stop when the quick
clamp switch turned OFF.

R25Z9A3CD23

(8) Overload warning lamp

① When the machine is overload, this lamp blinks during the
overload switch is ON.
② Reduce the machine load.

R25Z9A3CD24

3-6
CLUSTER (MACHINE SERIAL NO.: #0306~)

The cluster consists of gauges and lamps as shown below, to warn the operator in case of abnor-
mal machine operation or conditions for the appropriate operation and inspection.
· Gauges : Indicate operating status of the machine.
· Warning lamp : Indicate abnormality of the machine (red).
· Pilot lamp : Indicate operating status of the machine.
※ The cluster installed on this machine does not entirely guarantee the condition of the
machine. Daily inspection should be performed according to chapter 6, Maintenance.
※ When the cluster provides a warning, immediately check the problem and perform the
required action.

Battery charging warning lamp

Engine oil pressure warning lamp Engine preheat pilot lamp

Quick clamp pilot lamp Overload warning lamp
Engine coolant temp warning lamp Fuel low level warning lamp
Engine coolant temp gauge Fuel level gauge
Travel speed pilot lamp

Up/Left button Enter/Buzzer stop button

Down/Right button OLED display Menu button

17Z9A3CD03B

3-6-1
1) GAUGES AND DISPLAYS
(1) Service meter
① This meter shows the total operation hours of the machine.
② Always ensure the operating condition of the meter during the
machine operation.
Inspect and service the machine based on hours as indicated
in chapter 6, maintenance.
17Z9A3CD20

(2) Fuel gauge

① This gauge indicates the amount of fuel in the fuel tank.
② Fill the fuel when the red range or warning lamp ON.
※ If the gauge illuminates the red range or warning lamp
ON even though the machine is on the normal condition,
check the electric device as that can be caused by the poor
connection of electricity or sensor.
Red range
17Z9A3CD21

(3) Engine coolant temperature gauge

① This indicates the temperature of coolant.
Red ·Red range : Above 115°C (239°F )
range ② When the red range pointed or warning lamp ON, engine
do not abruptly stop but run it at medium speed to allow it to
cool gradually, then stop it.
Check the radiator and engine.
※ If the engine is stopped without cooled down running, the
17Z9A3CD22
temperature of engine parts will rise suddenly, this could
cause severe engine trouble.

3-6-2
2) WARNING AND PILOT LAMPS
(1) Fuel low level warning lamp
① This lamp blinks and buzzer sounds when the level of fuel is
low.
② Fill the fuel immediately when the lamp blinks.

R5573CD10

(2) Engine coolant temperature warning lamp

① This lamp blinks and buzzer sounds when the temperature of
coolant is over the normal temperature 115°C (239°F ) .
② Check the cooling system when the lamp blinks.

R25Z9A3CD08

(3) Engine oil pressure warning lamp

① This lamp blinks and buzzer sounds after starting the engine
because of the low oil pressure.
② If the lamp blinks during engine operation, shut OFF engine
immediately. Check oil level.

R5573CD13

(4) Battery charging warning lamp

① This lamp blinks and buzzer sounds when the starting switch is
ON, it is turned OFF after starting the engine.
② Check the battery charging circuit when this lamp blinks during
engine operation.

R5573CD16

3-6-3
(5) Engine preheat pilot lamp
① When the start switch turn to HEAT position, pilot lamp comes
ON.
② Refer to the page 4-4 for details.

17Z9A3CD25

(6) Quick clamp lock pilot lamp

① When the quick clamp switch turned ON, this lamp turn ON
and the buzzer sounds.
② This lamp turned OFF and the buzzer stop when the quick
clamp switch turned OFF.

17Z9A3CD26

(7) Travel speed pilot lamp

① When this lamp turned ON, the machine travel high speed.
② Refer to the travel speed control switch in page 3-9 for details.

35Z9A3CD81

(8) Overload warning lamp

① When the machine is overload, this lamp blinks during the
overload switch is ON.
② Reduce the machine load.

R25Z9A3CD24

3-6-4
3) BUTTONS
(1) Up/left button
① Move in menu (up, left)
② Increase input value.

17Z9A3CD27

(2) Down/right button

① Move in menu (down, right)
② Decrease input value.

17Z9A3CD28

(3) Menu button

① Current display to next display.

17Z9A3CD29

(4) Enter and buzzer stop button

① Select menu (enter).
② Stop buzzer sound when sound is ON.

17Z9A3CD30

3-6-5
4) OLED display
(1) Main display
① Service meter : This meter shows the total operation hours of
Service meter the machine.
※ Always ensure the operating condition of the service meter
during the machine operation.
② Engine rpm : This displays the engine speed.
Engine rpm
③ Engine run status : This displays the engine run ststus.
Engine run status
17Z9A3CD33

(2) Machine security

① ESL (Engine Starting Limit) mode setting
- ESL mode is designed to be a theft deterrent or will pre-
vent the unauthorized operation of the machine.
- If the ESL mode was selected Always, the password will
Press
be required when the start switch is turned ON.
- Disable : Not used ESL function.
Always:The password is required whenever the
operator start engine.
Press
Interval : The password is required when the operator start
engine first. But the operator can restart the en-
gine within the interval time without inputting the
password.
The interval time can be set maximum 2 days.
· Interval
Interval time
- If set interval time to 5 minutes, ESL system is activated after
Delete
Enter 5 minutes. Therefore, the password does not need to restart
engine within 5 minutes.

17Z9A3CD34
※ Default passwor
password
d : 00000

② Password change
- Input 5 to 10 digits and press Enter.

Delete
Enter

17Z9A3CD37

3-6-6
3. SWITCHES

Main light switch

Beacon switch

Switch Switch
panel 2 panel 3

Switch
panel 1

Master switch

Location on engine
hood support

Horn switch

Travel speed control switch

RH (#0306-)
LH
R25Z9A3CD13-1

1) STARTING SWITCH
(1) There are three positions, OFF, ON and START.
· (OFF) : None of electrical circuits activate.
· (ON) : All the systems of machine operate.
· (START) : Use when starting the engine. Release key imme-
diately after starting.
※ Key must be in the ON position with engine running to maintain
21073CD27 electrical and hydraulic function and prevent serious machine
damage.

3-7
2) MAIN LIGHT SWITCH
(1) This switch use to operates the head light and work light by two step.
·First step : Head light and cluster illumination lamp comes ON.
·Second step : Work light comes ON. Also, the below indicator
lamp comes ON.

R5573CD80

3) HEATER SWITCH
(1) This switch use to operates the heater by two step.
·First step : Low fan speed
·Second step : High fan speed

R5573CD81

4) WIPER AND WASHER SWITCH

(1) The switch use to operates the wiper and washer by two step.
·First step : The wiper operates.
·Second step : The washer liquid is sprayed and the wiper is operat-
ed only while pressing. If release the switch,
return to the first step position.

R5573CD82

5) TRAVEL ALARM SWITCH (option)

(1) This switch is the signal to alarm surroundings when the machine
travels to forward and backward.
(2) On pressing this switch, the alarm operates only when the machine
is traveling.

R5573CD83

3-8
6) TRAVEL SPEED CONTROL SWITCH (machine serial NO. : -#0305)
(1) This switch is used to control the travel speed.
1 : ① Low speed
2 : ② High speed

R35Z73CD82

7) TRAVEL SPEED CONTROL SWITCH (machine serial NO. : #0306-)

Travel lever(RH) (1) This switch is to control the travel speed which is changed to high
speed by pressing the switch and low speed by pressing it again.
Switch (2) When the machine travel high speed, the travel speed pilot lamp
lights ON.

35Z9A3CD85

8) BEACON SWITCH (option)

(1) This switch turns ON the rotary light on the cab.
(2) The below indicator lamp is turned ON when operation this switch.

21073CD38

9) QUICK CLAMP SWITCH (option)

(1) This switch is used to engage or disengage the moving hook on
quick clamp.
※ Refer to the page 8-6 for details.

21073CD36

10) MASTER SWITCH

(1) This switch is used to shut off the entire electrical system.
(2) I : The battery remains connected to the electrical system.
O : The battery is disconnected to the electrical system.
※ Never turn the master switch to O (OFF) with the engine running.
It could result in engine and electrical system damage.
OFF
7579A3CD30

3-9
11) HORN SWITCH
Horn switch (1) This switch is at the top of left side control lever.
On pressing, the horn sounds.

LH RCV lever
R35Z73CD83

12) OVERLOAD SWITCH (option)

(1) When this switch turned ON, buzzer makes sound and overload
warning lamp comes ON in case that the machine is overload.
(2) When it turned OFF, buzzer stops and warning lamp goes out.

R25Z9A3CD30

3-10
4. LEVERS AND PEDALS

Dozer control lever

Engine speed
RH control lever control lever

Travel lever
LH control lever
Boom swing pedal
Travel pedal
Double acting pedal

R35Z73CD12

1) LH CONTROL LEVER
(1) This joystick is used to control the swing and the arm.
(2) Refer to operation of working device in chapter 4 for details.

R35Z73CD20

2) RH CONTROL LEVER
(1) This joystick is used to control the boom and the bucket.
(2) Refer to operation of working device in chapter 4 for details.

R35Z73CD21

3-11
3) SAFETY LEVER
(1) All control levers are disabled from operation by locating the lever to
lock position as shown.
※ Be sure to raise the lever to LOCK position when leaving from
Lock operator's seat.
(2) By pushing lever to UNLOCK position, machine is operational.
※ Do not use the safety lever for handle when getting on or off the
Unlock R35Z73CD36
machine.

4) TRAVEL LEVER
(1) This lever is mounted on travel pedal and used for traveling by hand.
The operation principle is same as the travel pedal.
(2) Refer to traveling of the machine in chapter 4 for details.

R35Z73CD35

5) TRAVEL PEDAL
(1) This pedal is used to move the machine forward or backward.
(2) If left side pedal is pressed, left track will move.
If right side pedal is pressed, right track will move.
(3) Refer to traveling of machine in chapter 4 for details.

R35Z73CD34

6) ENGINE SPEED CONTROL LEVER

(1) This lever is used to increase or decrease the rotation speed of
Increase engine.
Decrease
(2) Move the lever backward to increase engine RPM. Move the lever
forward to decrease engine RPM.
(3) When stopping the engine, move the engine speed control lever for-
R35Z73CD37 ward completely and turn key OFF.

3-12
7) DOZER CONTROL LEVER
(1) This lever is used to operate the dozer blade.
Dozer control lever
(2) If the lever is pushed forward, the dozer blade will be going down.
If the lever is pulled back, the dozer blade will be going up.

R35Z73CD38

8) BOOM SWING PEDAL

(1) This pedal is used to swing the boom to the right and left direction.

Unlock Lock (2) Move the lock cover to unlock position by foot.
(3) The pedal is pressed to left side, boom will swing to the left direction.
Lock
cover The pedal is pressed to right side, boom will swing to the right direc-
Boom swing pedal tion.
R35Z73CD40

3-13
5. HEATER

Heater is equipped for pleasant operation against outside temperature.

(Heater only)

R27Z93CD81

1) OUTLET CONTROL LOUVER

(1) The direction of air can be controlled.
It can be closed or opened.

R35Z73CD74

3-14
6. OTHERS

VOLUME
+

VOLUME
1
-
2
3

HYU
4 NDA
I
5 BAND
AST

TA
SOURCE
RDS

Speaker
Radio & USB player

Seat
Cigar lighter

Fuse box

R25Z9A3CD14

1) CIGAR LIGHTER
(1) This can be used when the engine starting switch is ON.
(2) The lighter can be used when it springs out in a short while after
being pressed down.
※ Service socket
13033CD69 Use cigar lighter socket when you need emergency power.
Do not use the lighter exceeding 12
12V,, 120W.
120

3-15
2) SEAT
The seat is adjustable to fit the contours of the operator's body. It will reduce operator fatigue due
to long work hours and enhance work efficiency.

(1) For/aft adjustment (A)

The seat can be positioned over a range 52mm,
giving you plenty of room to maneuver in every
height and work situation.
(2) Seatback angle adjustment (B)
The seatback adjusts over a range of -5。 to +25。
with 18 locking positions, to give your back full sup-
port for every job and make sure you feel best.

Tether (3) Weight adjustment (C)

Just sit down, press the smooth-action lever, click,
A
and you're primed for action, with optimum suspen-
C sion for all operator weights between 45 and 136 kg
(99 and 300 lb). Design comfort with driver appeal-
it only takes one simple action to adjust the sus-
pension to the ideal sitting position that's best for
you and your back.

Seatbelt
(4) Seatbelt system
The seatbelt provides freedom of movement, yet
ensure that you're safety restrained in your seat,
B
even if your vehicle should crash or tip over.
Always check the condition of the seat belt and
mounting hardware before operating the
machine.
Replace the seat belt at least once every three
years, regardless of appearance.
R27Z93CD16

3) UPPER WINDSHIELD
(1) Perform the following procedure in order to open the upper windshield.
Hold both grips that are located both side of the windshield frame.
Move grips to inside in order to release the lock latches.
Hold both grips and push the windshield upward.
Hold both grips and back into the storage position.
Unlock
Grip Release both grips carefully until lock latches are into the locking
position.
Hold both grips and back into the storage position.
Release both grips carefully until lock latches are into the locking
R35Z73CD41
position.
When working, without having locked the windshield by the auto lock
(by pushing the windshield to the rear untill it's completely fixed),
please be careful as it can cause personal injury if the windshield is
not fixed or falls off.
(2) Perform the following procedure in order to close the upper windshield.
Reverse step through step in order to close the upper wind-
shield.
3-16
4) FUSE BOX
(1) The fuses protect the electrical parts and wiring
20A

20A
BEACON

SPARE,10A
WIPER MOTOR
20A CASSETTE from burning out.

20A
HORN, CIGAR CABIN LAMP
(2) The fuse box cover indicates the capacity of each
fuse and circuit it protects.
20A

20A
SAFETY SOL. WORK LAMP
TRAVEL SOL. ※ Replace a fuse with another of the same
SPARE,20A
capacity.
10A

20A
FUEL FEED HEATER
PUMP, ALT. Before replacing a fuse, be sure to turn OFF
the starting switch.
20A

20A

OPTION
SPARE
SPARE,20A

10A

MONITOR
RADIO
PULLER
FUSE

20A

B+

R27Z93CD60

3-17
 5) RADIO AND USB PLAYER ((machine
machine serial No. : -#0154)

14 LCD display 1 13

3 4 2 5 6 7 8 9 10 11 12

75793CD62

■FRONT
FRONT PANEL PRESENTATION

1 SEL -------- Sound function selection button 10 6 -------- Preset memory button 6
(audio selection) D+ --------------- Directory up
2 -------- Power and volume button 11 -------- Aux function

12 BSM -------- Preset scan (PS)

3 MODE -------- Mode button
Best station memory (BSM)
(select RADIO / USB / AUX)
13 MUTE -------- Audio mute button
4 ------- UP / DOWN tuning button
14 AM/FM -------- AM / FM button (radio)
5 1 ------- Preset memory button 1
DISP ---------- ID3 v2 display
6 2 ------- Preset memory button 2
SCN ------------ File scan
7 3 ------- Preset memory button 3
RPT ------------ Repeat play selector
8 4 ------- Preset memory button 4
RDM ------------ Random play selector
9 5 ------- Preset memory button 5
D- ---------------- Directory down

3-18
■GENERAL
GENERAL
(1) Power and volume button
① Power ON/OFF button
Press power button to turn the unit ON or OFF shortly.
When the power is ON, the previous mode (last memory) will
appear.
75793CD66 ② Volume
olume up / down control
Turn volume up / down button right to increase the volume level. The
level will be shown in VOLUME xx on the LCD display. Turn it left to
decrease the volume level. After 5 seconds of volume indication,
display will return to the previous mode.

(2) Sound function selection button (audio selection)

① This button is to adjust the sound. Each time you press power but-
ton shortly, LCD displays each mode as follows :
SEL
BASS TREBLE BAL BEEP LOUD VOLUME
75793CD65

※ When this button is pressed, LCD display shows selected function

for 5 seconds and then returns back to the previous mode. On
selected function, level can be controlled by turning this button. The
display will automatically return to normal indication in 5 seconds
after the last adjustment is made or when another function is acti-
vated.
② Bass
ass control
To adjust the bass level, first select the bass mode by pressing the
select button SEL
until BASS indication appears on the LCD display.
Within 5 seconds of choosing the bass mode, turn power button
right / left to adjust the bass level as desired.
The bass level will be shown on the LCD display from a minimum of
BASS –10 to a maximum of BASS +10.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is acti-
vated.
③ Treble
reble control
To adjust the treble level, first select the treble mode by pressing the
select button SEL
until TREBLE indication appears on the LCD dis-
play. Within 5 seconds of choosing the treble mode, turn power but-
ton right / left to adjust the treble level as desired.
The treble level will be shown on the LCD display from a minimum
of TREBLE -10 to a maximum of TREBLE +10.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is acti-
vated.

3-19
 ④ Balance
alance control
To adjust the left-right speaker balance, first select the balance
mode by pressing the select button SEL
until the BAL indication
appears on the LCD display.
Within 5 seconds of choosing the balance mode, turn power button
right / left to adjust the balance as desired.
The balance position will be shown on the LCD display from BAL
10L (full left) to BAL 10R (full right).
When the volume level between the left and right speakers is equal,
BAL L=R will be shown on the LCD display panel.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is acti-
vated.
⑤ Beep
eep control
To adjust the beep mode, first select the beep mode by pressing the
select button SEL
until BEEP indication appears on the LCD display.
The beep mode will be shown on the LCD display from BEEP 2ND,
BEEP OFF and BEEP ON by turning power button right / left.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is acti-
vated.
Select BEEP ON when you wish to hear the BEEP sound whenever
any function button is pressed.
Select BEEP 2ND when you wish to hear the BEEP sound whenev-
er any tuner pre-set button and/or tune seek buttons are pressed for
more than 3 seconds.
⑥ Loud
oud control
When listening to music at low volume levels, this feature will boost
the bass and treble response.
This action will compensate for the reduction in bass and treble per-
formance experienced at low volume.
To select the loudness feature, press select button until LOUD
SEL

ON or LOUD OFF is displayed, then turn power button left or right

to activate or deactivate loudness.

(3) Mode button

① Press mode button to select RADIO / USB / AUX.

MODE

75793CD67

(4) Audio mute button

① Press mute button momentarily to mute volume and MUTE
mark will blink on the LCD display.
MUTE Press the button again to return to the mode in use before the
mute mode was activated.
75793CD77

3-20
■RADIO
RADIO
(1) AM / FM / LW band selector
① Each time this button is pressed, the radio button is changed.
Each time this button is pressed, LCD displays each band as
AM/FM follows :
FM1 FM2 FM3 AM LW
75793CD78

※ LW band is only available for Europe.

(2) Up / down tuning

① To automatically select a radio station, momentarily press the up
tune seek button or down tune seek button for less than 3
seconds to search for the closest radio station.
To manually select a radio station, press the up tuning & down
75793CD68 tuning button for longer than 3 seconds.
The radio frequency will move up or down step by step each
time you press button.

(3) Station pre-set button

① Pressing these buttons shortly will recall your favorite pre-set
1 2
radio stations.
To store your favorite stations into any of the 6 pre-set memories
3 4 in each band (AM/FM/LW), use the following procedure :
a. Turn the radio ON and select the desired band.
5 6 b. Select the first station to be pre-set using the manual up/
75793CD69~74 down or automatic seek tuning control button.
c. Press the chosen pre-set button to store your selected station
into and continue to hold it in. The beep sound will be
momentarily heard and the pre-set number will apear on the
LCD display indicating that the station is now set into that
pre-set memory position and can be recalled at any time, by
pressing that pre-set button.

3-21
 (4) Pre-set scan (PS) / Best station memory (BSM) button
① Pre-set scan (PS)
Press BSM button shortly to scan the 6 pre-set station stored the
BSM memories on each band (AM/FM/LW).
The unit will stop at each pre-set station (the pre-set number on the
75793CD76 LCD display will flash during pre-set scan operation) and remain on
the selected frequency. Press the button momentarily again to
remain on the station currently being heard.
② Best station memory (BSM)
Pressing BSM button for longer than 2 seconds will activate the
BSM tuning feature which will automatically scan and enter each
station into memory.
If you have already set the pre-set memories to your favorite sta-
tions, activating the BSM tuning feature will erase those stations
and enter the new ones.
This BSM feature is most useful when traveling in a new area where
you are not familiar with the local stations.

■USB
USB PLAYER
(1) USB function
There are two ways to play mp3 files in a USB device : using USB socket in the cab and the USB /
AUX cable connected to the front side of the player.
· Use of USB
USB socket
① Connect a USB device, which saves mp3 files, to USB socket in the cabin.
② If a USB device has not been connected, MP3 files are automatically played when you insert it
into the USB port.
③ If a USB device has connected, MP3 files are played when you press mode for USB.
· Use of USB / AUX cable (option)

75793CD81

① Connect the USB/AUX cable to the player in order to play MP3 files in a USB device.
② If a USB device has not been connected, MP3 files are automatically played when you
insert it into the cable.
③ If a USB device has connected, MP3 files are played when you press mode for USB.

3-22
(2) File selection & cue / review button
① File
ile selection function
This button is used to select file up / down. Each time the forward
file select is pressed, file number is increased.
Each time the backward file select is pressed, file number is
75793CD68 decreased.
② Cue
ue / review functions
High-speed audible search of file on a USB can be made by this
button (the cue and review functions).
Press and hold the cue button to advance rapidly in the forward
direction or the review button to advance rapidly in the backward
direction.

(3) MP3 directory / file searching

① The power button is used to select a particular directory and file.
Press and hold for more than 3 seconds while playing MP3 file.
Turn right / left the power button to search the directory. Press the button when you find the want-
ed directory.
For example, the directory search generally changes in two methods depending on the order of
writing as follows.
·Method 1 : ROOT Dir01 Dir02 Dir03 Dir04 Dir05 Dir06 Dir07
·Method 2 : ROOT Dir01 Dir02 Dir05 Dir03 Dir06 Dir04 Dir07

If you want to search the file in the located directory, turn right / left the power button consecu-
tively. Press the button when you find the wanted file. The unit will then play the selected file.
For instance, the file search changes in Dir01 as follows.

File01 File02 File03 File04

※ MP3 direction / file configuration

ROOT

Directory01

File01 File02 File03 File04 Dir02 Dir03 Dir04

File05 File06 Dir05 File07 File08 Dir06 File09 File10 Dir07

3-23
(4) ID3 v2 display
① Disp button is used to change the display information.
While playing an MP3 file, you can change the file information
1 DISP shown on the LCD display.
Each time you press DISP (display), the display changes to show
75793CD82 the following.
※ If the MP3 disc does not have any ID3 information, the display will
show NO ID3 on LCD display.

Directory name / file name (normal mode)

Album name / performer / title

File number / elapsed time

(5) File scan (SCN)

① During USB play, press SCN button to play the first 10 seconds of
each file on the whole file on the USB (SCN mark will appear on the
2 SCN LCD display).
When a desired file is reached, press the SCN button again to can-
75793CD83 cel the function.
The unit will then play the selected file.
※ In case of playing MP3 file, when the SCN (scan) button is pressed
and held for longer than 2 seconds, the SCN mark will blink on the
LCD display and all files in the selected directory will be introduced
until the file scan mode is cancelled by pressing the SCN button
again or by activating the random or repeat functions.

(6) Repeat play selector (RPT)

① During USB play, press RPT button to play the selected file repeat-
edly (RPT will appear on the LCD display).
3 RPT Play of the file will continue to repeat until this button is pressed
again and the RPT disappears from the LCD display.
75793CD84 ※ In case of playing MP3 file, when the RPT button is pressed and
held longer than 2 seconds, the RPT mark will blink on the LCD dis-
play and play all files in the selected directory and will be repeated
until the directory repeat mode is cancelled by pressing the repeat
button again or by activating the scan or random functions (RPT
mark will disappear from LCD display).

3-24
 (7) Random play selector (RDM)
① During USB play, press RDM button to play the files on the USB in a
random shuffled order (RDM will appear on the LCD display). The
4 RDM file select function will also select file in the random order instead of
the normal process.
75793CD85 The random play mode can be cancelled by this button again.
※ In case of MP3 file, when the random button is pressed and held
longer than 2 seconds, the RDM mark will blink on the LCD display
and play all files in directory randomly until the directory random
mode is cancelled by pressing the random button again or by acti-
vating the scan or repeat functions (RDM mark will disappear from
LCD display).

(8) Directory down

① Press D- button briefly while playing MP3. The previous directory is
located each time you press this button.
5 D-

75793CD86

(9) Directory up
① Press D+ button briefly while playing MP3 . The next directory is
located each time you press this button.
6 D+ ※ If the MP3 file does not have a directory, the unit play MP3 at
10-file intervals.
75793CD87 ※ If any MP3 file does not exist in USB, this button can not oper-
ate.

■AUX
AUX PLAYER
(1) Aux function
· Use of USB socket
① If you want to listen to music of a external audio device, connect a
external audio device into the USB port.
② Press mode button to change a current mode for AUX. If audio file
AUX USB
of audio device is playing, you can listen to music through speaker.
HB1003CD63

· Use of USB /AUX cable (option)

① If you want to listen to music of a external audio device, connect a
external audio device through USB / AUX cable.
② Press mode button to change a current mode for AUX. If audio file
of audio device is playing, you can listen to music through speaker.
75793CD75

3-25
 RADIO AND USB PLAYER ((machine
machine serial No. : #0155-)

11 17 3 LCD display 12 14 13 15

EQ

LOUD

4 2 5 6 7 8 9 10 1 16
R25Z9A3CD38

■FRONT
FRONT PANEL PRESENTATION

1 SEL -------- Audio selection button 10 6 -------- Preset memory button 6

D+ --------------- Directory up
-------- Audio selection knob
11 -------- Aux function

BSM
2 -------- Power and volume button 12 -------- Preset scan (PS)
Best station memory (BSM)
MODE
3 -------- Mode button 13 MUTE -------- Audio mute button
(select RADIO / USB / AUX)
14 AM/FM -------- AM / FM button (radio)
4 ------- UP / DOWN tuning button
15 -------- Equalizer

16 -------- Loud
5 1 ------- Preset memory button 1
DISP ---------- ID3 v2 display 17 AUX -------- Aux connector
6 2 ------- Preset memory button 2
SCN ------------ File scan
7 3 ------- Preset memory button 3
RPT ------------ Repeat play selector
8 4 ------- Preset memory button 4
RDM ------------ Random play selector
9 5 ------- Preset memory button 5
D- ---------------- Directory down

3-26
■GENERAL
GENERAL
(1) Power and volume button
① Power ON/OFF button
Press power button to turn the unit ON or OFF shortly.
When the power is ON, the previous mode (last memory) will
appear.
75793CD66 ② Volume
olume up / down control
Turn volume up / down button right to increase the volume level. The
level will be shown in VOLUME xx on the LCD display. Turn it left to
decrease the volume level. After 5 seconds of volume indication,
display will return to the previous mode.

(2) Sound function selection button/knob (audio selection)

① This button is to adjust the sound. Each time you press SEL button
shortly, LCD displays each mode as follows :
SEL
BASS TREBLE BAL LOUD EQ BASS
Button
※ When this button is pressed, LCD display shows selected function
290F3CD45
for 5 seconds and then returns back to the previous mode. On
selected function, level can be controlled by turning this button. The
display will automatically return to normal indication in 5 seconds
after the last adjustment is made or when another function is
activated.
Knob ② Bass
ass control
290F3CD46
To adjust the bass level, first select the bass mode by pressing the
SEL button until BASS indication appears on the LCD display.
Within 5 seconds of choosing the bass mode, turn selection knob
right / left to adjust the bass level as desired.
The bass level will be shown on the LCD display from a minimum of
BASS –10 to a maximum of BASS +10.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is
activated.
③ Treble
reble control
To adjust the treble level, first select the treble mode by pressing the
SEL button until TREBLE indication appears on the LCD display.
Within 5 seconds of choosing the treble mode, turn selection knob
right / left to adjust the treble level as desired.
The treble level will be shown on the LCD display from a minimum
of TREBLE -10 to a maximum of TREBLE +10.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is
activated.

3-27
④ Balance
alance control
To adjust the left-right speaker balance, first select the balance
mode by pressing the SEL button until the BAL indication appears
on the LCD display.
Within 5 seconds of choosing the balance mode, turn selection
knob right / left to adjust the balance as desired.
The balance position will be shown on the LCD display from BAL
10L (full left) to BAL 10R (full right).
When the volume level between the left and right speakers is equal,
BAL L=R will be shown on the LCD display panel.
The display will automatically return to the normal indication in 5
seconds after the last adjustment or when another function is
activated.
⑤ Loud
oud control
When listening to music at low volume levels, this feature will boost
the bass and treble response.
This action will compensate for the reduction in bass and treble
performance experienced at low volume.
To select the loudness feature, press SEL button until LOUD ON or
LOUD OFF is displayed, then turn selection knob left or right to
activate or deactivate loudness.
⑥ Equalizer (EQ)
You can select an equalizer curve designed for 4 music types (POP,
ROCK, CLASSIC, JAZZ).
To select the desired curve, first select the EQ mode by pressing
SEL button until the "EQ OFF" indication appears on the display
panel. Within 5 seconds of choosing the EQ mode, turn selection
knob to select an equalizer curve as desired.

3-28
 (3) Mode button
① Press mode button to select RADIO / USB / AUX audio.
MODE

290F3CD44

(4) Audio mute button

① Press mute button momentarily to mute volume and MUTE
mark will blink on the LCD display.
MUTE Press the button again to return to the mode in use before the
mute mode was activated.
75793CD77

■RADIO
RADIO
(1) AM / FM / LW band selector
① Each time this button is pressed, the radio button is changed.
Each time this button is pressed, LCD displays each band as
AM/FM follows :
FM1 FM2 FM3 AM LW FM1
75793CD78

※ LW band is only available for Europe.

(2) Up / down tuning

① To automatically select a radio station, momentarily press the up
tune seek button or down tune seek button for less than 3
seconds to search for the closest radio station.
To manually select a radio station, press the up tuning & down
tuning button for longer than 3 seconds.
290F3CD43
The radio frequency will move up or down step by step each
time you press button.

(3) Station pre-set button

① Pressing these buttons shortly will recall your favorite pre-set
1 2
radio stations.
To store your favorite stations into any of the 6 pre-set memories
3 4 in each band (AM/FM/LW), use the following procedure :
a. Turn the radio ON and select the desired band.
5 6 b. Select the first station to be pre-set using the manual up/
75793CD69~74 down or automatic seek tuning control button.
c. Press the chosen pre-set button to store your selected station
into and continue to hold it in. The beep sound will be
momentarily heard and the pre-set number will apear on the
LCD display indicating that the station is now set into that
pre-set memory position and can be recalled at any time, by
pressing that pre-set button.

3-29
 (4) Pre-set scan (PS) / Best station memory (BSM) button
① Pre-set scan (PS)
Press BSM button shortly to scan the 6 pre-set station stored the
BSM
memories on each band (AM/FM/LW).
The unit will stop at each pre-set station (the pre-set number on the
290F3CD42 LCD display will flash during pre-set scan operation) and remain on
the selected frequency. Press the button momentarily again to
remain on the station currently being heard.
② Best station memory (BSM)
Pressing BSM button for longer than 2 seconds will activate the
BSM tuning feature which will automatically scan and enter each
station into memory.
If you have already set the pre-set memories to your favorite sta-
tions, activating the BSM tuning feature will erase those stations
and enter the new ones.
This BSM feature is most useful when traveling in a new area where
you are not familiar with the local stations.

■USB
USB PLAYER

EQ

LOUD

R25Z9A3CD39

(1) USB function

① Connect a USB device if you want to listen to MP3 file in a USB device.
② It will automatically play MP3 file in the USB device and the LCD display will show “READING
USB”.
※ If there are no files on USB device, playback will revert back to the previous mode after display-
ing “NO FILE”.
(2) AUX function
① If you want to listen to music of a external audio device, connect a external audio device through
AUX cable.
② Change AUX mode by pressing MODE button.
If audio file of Audio device is playing, you can listen to music through speaker.

3-30
(3) File selection & cue / review button
① File
ile selection function
This button is used to select file up / down.
Each time the forward file select is pressed, file number is
increased.
Each time the backward file select is pressed, file number is
290F3CD43
decreased.
② Cue
ue / review functions
High-speed audible search of file on a USB can be made by this
button (the cue and review functions).
Press and hold the cue button to advance rapidly in the forward
direction or the review button to advance rapidly in the backward
direction.

(4) MP3 directory / file searching

① The D-, D+ button is used to select a particular directory and file.
Press and hold for more than 3 seconds while playing MP3 file.
Turn right / left the selection knob to search the directory. Press the button when you find the
wanted directory.
For example, the directory search generally changes in two methods depending on the order of
writing as follows.
·Method 1 : ROOT Dir01 Dir02 Dir03 Dir04 Dir05 Dir06 Dir07 ROOT

·Method 2 : ROOT Dir01 Dir02 Dir05 Dir03 Dir06 Dir04 Dir07 ROOT

If you want to search the file in the located directory, turn right / left the selection knob
consecutively. Press the button when you find the wanted file. The unit will then play the
selected file.
For instance, the file search changes in Dir01 as follows.

File01 File02 File03 File04 File01

※ MP3 directory / file configuration

ROOT

Directory01

File01 File02 File03 File04 Dir02 Dir03 Dir04

File05 File06 Dir05 File07 File08 Dir06 File09 File10 Dir07

3-31
(5) ID3 v2 display
① Disp button is used to change the display information.
While playing an MP3 file, you can change the file information
1 DISP shown on the LCD display.
Each time you press DISP (display), the display changes to show
75793CD82 the following.
※ If the MP3 disc does not have any ID3 information, the display will
show NO ID3 on LCD display.

Directory name / file name (normal mode)

Album name / performer / title

File number / elapsed time

Directory name / file name (normal mode)

(6) File scan (SCN)

① During USB play, press SCN button to play the first 10 seconds of
each file on the whole file on the USB (SCN mark will appear on the
2 SCN LCD display).
When a desired file is reached, press the SCN button again to can-
75793CD83 cel the function.
The unit will then play the selected file.
※ In case of playing MP3 file, when the SCN (scan) button is pressed
and held for longer than 2 seconds, the SCN mark will blink on the
LCD display and all files in the selected directory will be introduced
until the file scan mode is cancelled by pressing the SCN button
again or by activating the random or repeat functions.

(7) Repeat play selector (RPT)

① During USB play, press RPT button to play the selected file repeat-
edly (RPT will appear on the LCD display).
3 RPT Play of the file will continue to repeat until this button is pressed
again and the RPT disappears from the LCD display.
75793CD84 ※ In case of playing MP3 file, when the RPT button is pressed and
held longer than 2 seconds, the RPT mark will blink on the LCD dis-
play and play all files in the selected directory and will be repeated
until the directory repeat mode is cancelled by pressing the repeat
button again or by activating the scan or random functions (RPT
mark will disappear from LCD display).

3-32
(8) Random play selector (RDM)
① During USB play, press RDM button to play the files on the USB in a
random shuffled order (RDM will appear on the LCD display). The
4 RDM file select function will also select file in the random order instead of
the normal process.
75793CD85 The random play mode can be cancelled by this button again.
※ In case of MP3 file, when the random button is pressed and held
longer than 2 seconds, the RDM mark will blink on the LCD display
and play all files in directory randomly until the directory random
mode is cancelled by pressing the random button again or by acti-
vating the scan or repeat functions (RDM mark will disappear from
LCD display).

(9) Directory down

① Press D- button briefly while playing MP3. The previous directory is
located each time you press this button.
5 D-

75793CD86

(10) Directory up
① Press D+ button briefly while playing MP3 . The next directory is
located each time you press this button.
6 D+ ※ If the MP3 file does not have a directory, the unit play MP3 at
10-file intervals.
75793CD87 ※ If any MP3 file does not exist in USB, this button can not oper-
ate.

3-33