—

RELEASE NOTES

RobotStudio 2024.3
 Contents
Release Notes for RobotStudio 2024.3 3
General 3
User documentation 3
Tutorials 3
System Requirements 3
New Functionality 5
Support Motor and Gear Units for OmniCore 5
Improvements 6
MultiMove for OmniCore in Controller From Layout 6
Show warning before editing VIEWONLY or READONLY modules 6
SLP Distributor updated 6
Corrections 7
Known Limitations 12
IO Configurator 6 12
Online 12
Online – Paint 12
Online – Integrated Vision 13
Offline 15
Conveyor Tracking 18
MultiMove 18
External Axis 18
Network Drives and UNC Paths 19
RAPID 19
Paint 20
Graphics and Geometry 20
ScreenMaker 21
RobotWare Compatibility 24
Supported RobotWare versions 24
RobotWare 5.05 and 5.06 Compatibility 24
RobotWare 5.07 Compatibility 24
RobotWare 5.08 Compatibility 24
RobotWare 5.10 Compatibility 24
RobotWare 5.11 Compatibility 24
RobotWare 5.12 Compatibility 25
RobotWare 5.13 Compatibility 25
RobotWare 5.15 Compatibility 25
RobotWare 6 Compatibility 26
General Compatibility Limitations 26

© Copyright 2024 ABB. All rights reserved. 2/26

Release Notes for RobotStudio 2024.3
General
The release name is RobotStudio 2024.3 and the build number is 24.3.10885.0. The build date is
September 3, 2024.
User documentation
The RobotStudio Operating Manual is available in all languages supported by RobotStudio except Czech,
i.e. English, German, French, Italian, Chinese, Japanese, Spanish. RobotWare manuals for IRC5 and
OmniCore can be installed from the Add-Ins Gallery.
Tutorials
Tutorials are available at the RobotStudio product pages at
https://new.abb.com/products/robotics/robotstudio.
System Requirements
Required Software
Microsoft Windows 10 Anniversary Edition or later, 64-bit edition, is required.
The Windows App Installer is a pre-requisite for the virtual OmniCore FlexPendant software, see
https://www.microsoft.com/en-us/p/App-Installer/9NBLGGH4NNS1. The App Installer is a default built-
in app in Windows 10 and later, but may have been removed on some PCs.
Sideloading of apps must be enabled on Windows to install the virtual OmniCore FlexPendant.
To enable sideloading follow these steps:
1. Open Settings.
2. Click Update & Security (Windows 10) or Privacy & security (Windows 11) > For developers.
3. Ensure Developer Mode is set to On.
Recommended Hardware
ITEM REQUIREMENT

CPU 2.0 GHz or faster processor, multiple cores recommended

8 GB minimum
Memory
16 GB or more if working with large CAD models

Disk 10+ GB free space, solid state drive (SSD)

Graphics High-performance, DirectX 11 compatible, gaming graphics card from any of the leading vendors.
Card¹ For the Advanced lightning mode Direct3D feature level 10_1 or higher is required.

Screen
1920 x 1080 pixels or higher is recommended
Resolution

Mouse Three-button mouse

3D Mouse Any 3D mouse from 3DConnexion, see http://www.3dconnexion.com.

© Copyright 2024 ABB. All rights reserved. 3/26

 ITEM REQUIREMENT

Meta Quest 2, HTC Vive or any Windows Mixed Reality Headset. Note that special PC hardware
Virtual
requirements apply when using RobotStudio with VR, see https://www.oculus.com/oculus-ready-
Reality
pcs/, https://www.vive.com/us/vive-ready/, or, https://www.microsoft.com/en-us/mixed-
Headset
reality/windows-mixed-reality, respectively.

¹ RobotStudio will not benefit from the additional features of so-called ‘Professional’ or ‘Workstation’
graphics cards. The price level of these are at a much higher range than gaming graphics cards with
comparable performance. High-end gaming PCs are very suitable for offline programming with
RobotStudio. Such a PC will provide good performance for a limited budget.

© Copyright 2024 ABB. All rights reserved. 4/26

New Functionality
Support Motor and Gear Units for OmniCore
Support Motor and Gear Units for OmniCore
Motor Units MU and Gear Units MID/MTD are now supported when creating an OmniCore Virtual
Controller from Layout.
Version 2.0 of the model packages is required, as well as the RobotWare add-in 'Motor and gear units for
OmniCore'.

© Copyright 2024 ABB. All rights reserved. 5/26

Improvements
MultiMove for OmniCore in Controller From Layout
Controller From Layout now supports MultiMove for the C90XT OmniCore controller.
Also the error message for when an unsupported robot/controller combination is selected has been
improved.
Show warning before editing VIEWONLY or READONLY modules
RAPID modules marked as VIEWONLY or READONLY are now displayed as read-only when opened in the
editor. Such modules should typically not be edited by the end user, and changes may not be included in
a backup.
A read-only module may be still edited by starting to type in the editor window and accepting the
disclaimer.

SLP Distributor updated

The SLP Distributor server has been updated to resolve an issue when using floating licenses.

© Copyright 2024 ABB. All rights reserved. 6/26

Corrections
Confusing message in Collision Avoidance

When clicking "Upload to Controller" in Collision Avoidance the user was advised restart the controller, even if the
controller was in manual mode with motors off. This issue has been fixed.

Error when trying to commit to a Cloud project where the project owner's license has expired

Cloud: The Commit command is now disabled with an explanatory tooltip if a project is read-only, for example if
the project owner's license has expired.

Save as Library and Disconnect Library corrections

The commands for Save and Disconnect library components have been corrected:
Save or Disconnect of a component that is part of a library hierarchy is not allowed.
Save as Library is now allowed for sub-components that are not part of a library hierarchy.

Inconsistent tool/robot visualization for joint targets

The View Tool at Target function has been corrected for joint targets. The tool base (mounting point) rather than
the TCP is now positioned to coincide with the selected target.

Expanding one folder in controller tree view opens another folder

Double-clicking the expander icon in a tree view will no longer cause the selected object to be activated.

Modify Position should not be possible on Offset/RelTool

In the Paths & Targets browser, the Modify Position command is now disabled for instructions that use Offs or
RelTool in the point argument.

Collision geometries memory use

Fixed an issue where generating collision geometries at high resolution level would use too much memory, and
eventually cause a crash.

Mismatch in Robot Position and Collision Geometry

Fixed an issue where the robot's collision geometry did not match the robot's pose when using the "Jump to
Move Instruction" feature with "Show collision geometry" enabled. This mismatch was specifically observed when
the "Select Robot Configuration" window was used during the operation.

View Tool at Target does not work for RelTool/Offs instructions

View Tool at Target now behaves correctly when selecting a move instruction that uses Offs or RelTool in the
target argument.

Decimals not visible in Joint Jog

Fixed an issue in Mechanism Joint Jog that could cause joint value decimals to disappear on high-DPI displays.

Diff visible when text comparison is not available

Cloud: In the Resolve Conflicts window, the text comparison view was visible even when a binary file was selected.
This issue has been fixed.

© Copyright 2024 ABB. All rights reserved. 7/26

 Surface From Curve fails for non-closed curve

Surface - Create From Curve now checks that the selected curve is closed before Create can be clicked.

Remove controller removes robots

When removing a Virtual Controller from a station, connected mechanisms are no longer removed if the user
selects to keep controller data in the station.

RobotStudio starts very slow if license server is unreachable

RobotStudio now starts faster when a network license server has been specified but is not running or reachable.

Logoff all Users exception

Fixed an issue where it was possible to press 'Logoff all users' even on controllers that are disconnected, which
caused an exception.

New Project - Create From Backup add-in selection

Fixed an issue where certain add-in versions could not be selected when creating a New Project with the option
'Create From Backup'.

Copy positions not harmonized

It is now possible to copy position from the context menu and paste it in the position controls such as 'Set
position'. The same is possible in the other direction i.e. copy from position control and paste via context menu.
Both methods now use the clipboard.

Cannot copy/paste rotation values from Create Workobject window

Copy/paste is now available for position and orientation, separately, in the create workobject window.

Copy/paste option not shown for JointTargets

Previously menu buttons were shown when editing joint targets, despite no menu options being available. The
menu button will now only be shown where copy/paste or other relevant functionality is available.

Arc instruction templates are not loaded for OmniCore virtual controller

Arc instruction templates are now available in the station when adding an OmniCore virtual controller with
ArcWare.

Find optimal robot placement shows wrong target name

Find optimal robot placement had a bug where the target list would show incomplete names for move
instructions. It now shows the complete name of each instruction including the target.

System failure when creating a Virtual Controller with two robots and a positioner

Fixed an issue in Controller from Layout when creating an OmniCore MultiMove system with a positioner with
more than three axes such as IRP B.

© Copyright 2024 ABB. All rights reserved. 8/26

 Single-arm YuMi Collision Avoidance error

Fixed a bug where Collision Avoidance commands were erroneously enabled for a Single-Arm YuMi (IRB 14050)
without the required software option, and clicking them would result in an error message.

World Zone point edit is not possible

Fixed an issue in "Edit Instruction" that could make it impossible to edit point arguments of World Zone
definitions.

Show valid user names in login dialog

When logging in to an IRC5 controller, the "User Name" dropdown will now only contain users configured on the
controller.
For an OmniCore controller, configured users will be shown if currently logged in with the "Manage UAS settings"
grant. Otherwise previously used user names will be shown.

'Find All References' for an I/O signal only works within the same task

In the RAPID editor, 'Find All References' for an I/O signal will now find references to the signal in all RAPID tasks.

Go Offline fails with RobotWare add-ins

Fixed an issue in Go Offline that caused RobotWare add-ins to be omitted in the created Virtual Controller.

Non Functional button

Previously menu buttons on various numeric text box controls were shown despite no menu options being
available. The menu button will now only be shown where copy/paste or other relevant functionality is available.

Conveyor model disappears when exporting to glTF

Fixed an issue where certain objects generated by Smart Components could be excluded when exporting a
station or simulation to a graphical format such as glTF.

Unable to resize UI control

A bug was introduced in 2024.2 that made it not possible to increase the height of some attached UI controls.
This has now been corrected.

Collision Free Path out of reach error

Collision Free Path could previously fail and incorrectly indicate that a target was out of reach. Now, the correct
reason for failure will be displayed.

Modify Mechanism not working

Fixed two issues in Modify Mechanism:

Fixed an exception that caused the command to fail for certain mechanisms.
Links that consist of more than one part are now displayed correctly when modifying an existing
mechanism.

© Copyright 2024 ABB. All rights reserved. 9/26

 VR initialization failed

Connecting an HTC Vive Pro 2 has been reported to fail with the error message "Motion Smoothing is enabled in
SteamVR," even though Motion Smoothing wasn't enabled.
It is now possible to connect with Motion Smoothing enabled. However, it is highly recommended to keep this
feature disabled to ensure optimal performance and avoid potential issues.

Brush events are not updated in Translate Path

Fixed an issue in Translate Path where SetBrush instructions were not updated to translate the trigger plane.

Graphics rendered in a single color

Fixed a rendering issue that could occur when doing a shallow box select with SHIFT+S being pressed, or when
creating a Safety Report in Visual SafeMove, if the station contained visible world zones or a conveyor with a
visible connection window. The issue caused all objects in the station to be rendered in a single color.

Collision Free Path: Offset and RelTool instructions issue

Previously, the Collision Free Path did not account for an offset to the target in an instruction. This issue has now
been addressed and resolved.

Show collision geometries fails after cancel

Cancelling the collision geometry generation could previously cause the subsequent attempts to fail, with the
output panel indicating that the operation was cancelled. This issue has now been resolved.

Simulation does not run with StopWatch Smart Component

Fixed an issue with the StopWatch Smart Component which caused the simulation to stop if no other component
kept it running.

Fatal Error when importing Station Logic

Fixed a crash that could occur if a property value could not be set when importing an xml file in Station Logic.
Also improved the logic for finding the object specified by a property value in the xml file.

Collision Free Path always fail

A bug has been corrected that made Collision Free Path fail every time if RobotWare 6.09 or earlier was used.

RobotWare add-ins missing in Pack & Go

RobotWare add-ins for OmniCore positioners, track motion and motor/gear units are now included in a Pack &
Go if required, so they don't need to be installed separately.

Incorrect track selection for the system created from backup

Create system from backup would suggest using IRT510 in place of IRT2005, even when the RobotWare version on
the controller is not compatible with that combination. Now this incompatibility is detected and it is no longer
allowed to create such a system.

Operating Mode - selected controller not visible

It was no longer possible to see or select the active Virtual Controller in the Operating Mode panel. This issue has
been fixed.

© Copyright 2024 ABB. All rights reserved. 10/26

 Signal Analyzer export recording - data lost

Fixed an issue where signal values would not be present in the exported excel and text files. The issue occurred
when a signal had multiple registered values within the same millisecond. This case is handled correctly now and
all values for such a signal will now be present in the exported recordings.

Load Program failed for user with only Load program controller grant

Load Program or Load Module from local PC requires write access to the controller disk on an IRC5 controller.
These commands are now disabled if the user logged in to the controller does not have the required grant.

Unpack & Work with SYSPAR on OmniCore

In Unpack & Work, the option for copying configuration files to the SYSPAR folder has been removed for
OmniCore virtual controllers since they do not support this feature.

© Copyright 2024 ABB. All rights reserved. 11/26

Known Limitations
IO Configurator 6
*Safety configuration problem with PROFIsafe Controller or CIP-Safety scanner
Changing safety settings in Visual SafeMove or IO Configurator 6 does not always work in conjunction
with the "PROFISafe controller" or "CIP-Safety Scanner" option. Connection with robot controller can be
lost during any IO-configuration, sometimes resulting in that the Flex Pendant reboots. Again this is only
applicable when the PROFISafe controller or CIP-Safety scanner option is present in the system. Problem
is dependent on how many devices are configured on respective industrial network. I.e. EtherNet/IP or
ProfiNet.
Online
Signal Analyzer Online recordings not saved
When recording signals from a real controller with RobotWare 6.13.03 and later, or RobotWare 7.6.1 and
later, there is a sporadic issue which causes the signal changes to not be recorded.
Routine variables can't be displayed in RAPID Watch with RobotWare 6.12
A limitation in RobotWare 6.12 prevents variables declared in a routine from being displayed in the RAPID
Watch window.
Port speed cannot be set at the same time as 'Obtain IP address automatically'
In the Public Network settings dialog the Port speed drop down menu is disabled when 'Obtain IP
address automatically' is selected.
Workaround:
1. Select 'Use the following IP address' and specify any valid IP address.
2. Select the desired port speed and press OK.
3. Select 'Obtain IP address automatically' and press OK.
Individual RAPID tasks cannot be stopped for RobotWare 5.60 and later
When running multitasking systems, it is not possible to start and stop individual tasks with the
dropdown menu of the task node in the Controller browser. This is due a restriction introduced with
RobotWare 5.60 and later. However, from RobotWare 6.03 onwards, then RAPID tasks to execute or to
stop can be selected from RobotStudio RAPID tab.
FlexPendant Viewer running with automatic reloading
When having FlexPendant Viewer running with automatic reloading of the screens and at the same time
jogging the robot with the joystick the robot jogging might halt when the FlexPendant Viewer reloads.
Cable harness not visible in Online Monitor
Physics-based dynamic cables that are part of a robot model are not visible in Online Monitor.
Online – Paint
Backup for Paint systems does not create backup of the PIB for IRC5P with RobotWare 5.xx
The Backup function of RobotStudio does not create a backup of the PIB board of the IRC5P system
when running RobotWare 5.xx. Workaround: Create the backup of the PIB board with the FlexPaint
Pendant using an USB-stick.

© Copyright 2024 ABB. All rights reserved. 12/26

Go Offline does not work for Paint systems
The Go offline function will not create a working Virtual controller system for Paint system unless the
Paint package I/O option is set to Simulated.
Online – Integrated Vision
Installation error when having previous versions of RobotStudio or Insight Explorer
If you have a previous version of RobotStudio or Cognex In-Sight software installed, installing a new
version of RobotStudio may result in the following error message
Module C:\Program Files (x86)\Common Files\Cognex\InSight\5.7.1674.0\CvsInSightDisplay.ocx failed
to register. HRESULT -2147220472. Contact your support personnel.
Workaround: To correct the issue, open Windows Settings -> Apps -> Apps & features, select the
current ABB RobotStudio 2019.x, select Modify, and step through the installation wizard and select
Repair. Alternatively, uninstall and reinstall RobotStudio.
Note: Only one version of the In-Sight Display Control can be registered at a time, and this is always the
latest version installed. Although older versions of RobotStudio or In-Sight may seem to function with
this version installed, their compatibility with this version is not guaranteed.
RobotStudio may hang for up to 60 seconds when configuring jobs with PatMax 1-50
The user interface of RobotStudio may freeze for up to 60 seconds when configuration Integrated
Vision jobs with the tool PatMax 1-50.
Workaround: Use PatMax 1-10 instead
Remaining error – New Emulators
New camera models have been added to the camera emulator option in RobotStudio 6.04.01. Some of
these new models are not yet fully compatible. Our recommendation is to choose a camera model from
the 7000 series which is fully compatible with Firmware version 4.10.2.
Emulated cameras not discovered when controller in Motors On
For RobotWare 5.61 onwards, the camera discovery mechanism is disabled when the controller is in
Motors On. As a consequence, the camera nodes will not appear in the controller browser.
Workaround: Switch to Manual Reduced Speed and use the Refresh command on the Integrated Vision
node in the browser to make the cameras appear.
Information – Camera firmware version and update
The minimum firmware version to be used with Integrated Vision is 4.08. If this version is not available for
a specific camera model, then the newest version available shall be used. There are two important things
to know before upgrading a sensor:
The user must make sure to first backup the files on the camera. This can be done using the Rapid
snippets for camera backup/restore, or the FlexPendant Explorer.
The latest available firmware version may vary across sensor types. However, when the firmware
update utility presents the latest available version it shows the firmware with the highest version
number which may not apply to the sensor to be updated. However, the appropriate firmware will
be applied.
Information – The spreadsheet view

© Copyright 2024 ABB. All rights reserved. 13/26

The spreadsheet view is not enabled when editing in the in the following modes “Add part location tool”,
“Add part inspection tool”. Before entering the spreadsheet mode click for example “Setup Image” or
Output to Rapid.
Information – Calibration board without fiducial
When using the calibration boards, checkerboard or board with dots, the user must select the preferred
origin by clicking and accepting (press enter) three points on the board. Only after these three points
have been selected it is possible to click "calibrate" to execute the calibration.
Information - Use default camera settings
If the camera is not using default communication settings the result may be that RAPID instructions
return error code “Communication Error”. The safest method to get default settings is to go to
Connect->Add Sensor Right click and select “Show all sensors”. Select the device to reset and click
“Apply factory settings” in the lower right corner. The most important settings are:

Telnet port: 23
User: "admin"
Password: ""

Information – User Credentials

It is now possible to create user profiles with different access levels on the camera. For detailed
information about this, please refer to the Integrated Vision User Manual.
Remaining error – Save image on camera
It is not possible to save an image on the camera using “Save Image”. This is by design, but the dialog
still allows the user to try to do this. The result is that the image is not saved and no error message is
given.
Remaining error - Connect button greyed out for no reason
It may sometimes happen that the “Connect” button is greyed out, with the tooltip saying the camera is
not on the correct subnet although the IP settings are OK.
Workaround: Restart the Integrated Vision Add-In
Remaining error – VC started from Controller->Add controller does not detect cameras
A VC that is started from Controller->Add controller does not detect cameras on the network, even if
the VC_network_definition.xml is correctly configured and the firewall is turned off. The reason is that
the controller is not able to detect new cameras on the network when it is in “Motors On” state. When
the VC is started stand-alone in RobotStudio it is automatically set to “Motors On“ when started.
Workaround: To allow it to discover cameras, turn the control panel key to manual mode or launch the
VC as part of a station.
User tip - Removing cameras from configuration
To remove a configured camera from the list of configured cameras, use the configuration editor. Enter
Configuration->Communication->Application Protocols and remove the desired camera. Perform a
warm start to complete the operation.
User tip – Viewing all cameras present on the network
Connect->Add Sensor is normally used for setting the IP addresses of sensors that are not currently on
the correct subnet (192.168.125.X). Since the dialog shows all cameras “seen” by the PC, this dialog is

© Copyright 2024 ABB. All rights reserved. 14/26

useful when error tracing camera network problems. If a camera does not appear on the network using
the “Add sensor” dialog as suggested above, it is advisable to cycle the power of the camera. If the
camera receives power from the controller, then cycle power by turning the mains switch.
User tip – Warm start the controller after changing network settings
Whenever changing the network settings of the camera, either from Connect->Add Sensor or Connect-
>Network settings, it is important to warm start the controller. If this is not done, RAPID instructions will
give the error “Communication Error” and the FTP-mounted camera disk is not accessible. If DHCP
address is used and persist, please try a static address instead.
Offline
Point cloud data in JT files can't be imported
Point cloud data in JT files is not imported by RobotStudio.
Issue with collision avoidance for palletizer robots
When configuring collision avoidance for a palletizer robot using RobotWare 6.11, attaching an object to
a mechanism link can result in an error and the configuration will not be loaded.
The YuMi library revision 1 cannot be successfully updated to YuMi revision 2
When opening a Pack&Go file with a station that has a reference to IRB14000_0.5_0.5__01.rslib you
get the option to update it to the newer IRB14000_0.5_0.5__02.rslib .
The following issues occurs if you select ‘Yes’ and update the model:
The attached parts, for example Smart Grippers, are detached.
The new YuMi robot is not connected to the virtual Controller.
The old YuMi mechanism is converted to a component.
Answer ‘No’ to this question to keep the original revision 1 model and avoid the problems mentioned
above.
RobotStudio needs to be restarted to update a modified library instance
When editing a library file (.rslib) that is used in a currently open station, then RobotStudio needs to be
restarted to update the library. Simply re-opening the station is not enough to update the content of
the station. Unless RobotStudio is restarted, the old library instance will remain in memory and be loaded
even though the underlying file has been updated. This is a known limitation and is expensive to fix.
There is a workaround to the problem, which is to restart RobotStudio.
The robot IRB 1600ID 1.55 m / 6kg replaced by IRB 1660ID1.55 m / 6 kg in RobotWare 6.04
The robot IRB 1600ID 1.55 m / 6 kg is not available in RobotWare 6.04 and later. It has been renamed to
IRB 1660ID 1.55 m / 6 kg. Virtual controller systems for IRB 1600ID 1.55 m / 6 kg based on RobotWare 6.03
cannot upgraded to RobotWare 6.04 and later. This means that Pack&Go files for this robot based on
RobotWare 6.03 cannot be upgraded to RobotWare 6.04 automatically
Workaround: Re-build or modify the virtual controller system to use IRB 1660ID 1.55 m / 6 kg instead
when using RobotWare 6.04 or later.
FlexPendant and RAPID applications run with logged in user rights
A FlexPendant or RAPID application running on the virtual controller runs with the rights of the logged-in
Windows user. RAPID applications running in a background task will start to execute when the Pack&Go

© Copyright 2024 ABB. All rights reserved. 15/26

file is opened and FlexPendant applications will start to execute when the user starts the Virtual
FlexPendant. A warning message has been added to the Unpack&Work wizard to make the user aware
that only Pack&Go files (.rspag) from trusted sources shall be opened.

Compatibility of RobotStudio Library and Stations with older RobotStudio versions

RobotStudio is generally not forwards compatible, i.e. it is not possible to load stations or libraries
created in RobotStudio 6.04 into an earlier version of RobotStudio such as e.g. RobotStudio 5.x, 6.03.02
or earlier. However, RobotStudio is backwards compatible, which means stations and libraries created
in versions 5.x, 6.03.02 or earlier can be opened in RobotStudio 6.04
TrueMove path visualization fails for customized zone data
The TrueMove path visualization function only supports predefined zonedata. It will not work for user
defined zonedata.
Backup fails for RobotStudio solutions with SafeMove or Electronic Position Switches
Backups are automatically created for virtual controller systems that are part of a RobotStudio solution
when saving the station. For virtual controller systems with the RobotWare options SafeMove or
Electronic Positioning Switches the backup will fail since these systems contain files that are read-only.
As a result, an error message is presented in the output window: <System name>: Backup failed . The
station will be successfully saved but there will be no backup created. Workaround: Ignore the error
message <System name>: Backup failed and create a manual backup whenever needed. The
RobotStudio Option “Enable automatic backup of controllers in solution” that is available in
”RobotStudio Options -> Robotics -> Virtual Controller” can be de-selected to disable the backup
function.
IRB 14000 cannot be combined with any other robot
The function system from layout fails if trying to create a MultiMove system where one robot is an IRB
14000. The reason is that the IRB 14000 cannot be combined with any other robot.
Workaround: Create a separate system for the IRB 14000.
The Work Envelope function does not support IRB 14000

© Copyright 2024 ABB. All rights reserved. 16/26

The function is disabled for the IRB 14000 and cannot be activated.
The 2D work envelope fails for certain robot models
As a result, the generated work envelop may appear distorted.
Update of current selection in the 3D graphics window may be delayed
A problem related to the graphics driver has been observed on certain PCs. The problem is that the
update of the current selection in the 3D graphics is delayed until the next redraw.
Workaround: Add or uncomment the following line in the file RobotStudio.exe.config

<add key=”DoublePresentWorkaround” value=”true” />

Failure to open Pack&Go file to same folder the second time

RobotStudio will prevent Pack&Go files to be opened to the same folder a second time if the station
contains VC systems with the EPS or SafeMove option. This is by design to prevent the safety controller
configuration file to be accidentally overwritten.
Workaround: Remove the write protection manually using Windows Explorer.
Updates of instruction template and code snippets
RobotStudio will not automatically update the user files for instruction templates and code snippets
files in the folders:
…\My Documents\RobotStudio\Instruction Templates
…\My Documents\RobotStudio\Code snippets
Workaround: The user has to manually copy the latest files from
%ProgramFiles%\ABB Industrial IT\Robotics IT\RobotStudio 5.xx\Instruction Templates
and
%ProgramFiles%\ABB Industrial IT\Robotics IT\RobotStudio 5.xx\Code Snippets
to the data folder.
I/O signals configured with access level 'DEFAULT'
When IO signals are configured with access level 'DEFAULT', only input signals are possible to set/reset
from the I/O Simulator and I/O Window. To be able to affect also output signals, set the access level to
‘ALL’ for them in the Configuration Editor.
VC does not start with RRI option and GSI folder structure missing
The VC will hang when started with a system containing the RobotWare option RRI (Robot Reference
Interface) if the GSI folder structure is missing.
Workaround: Create GSI Folder before starting the VC inside the HOME directory of the system. See the
Application Manual for Robot Reference interface for more information.
System in Guard Stop state in Automatic mode after run-time error
Certain run-time errors may cause the controller system to enter Guard Stop state in Automatic mode.
This is the same behavior as in a physical robot controller system. This typically happens when a run-time
error related to Conveyor Tracking occurs. A simulation cannot be started when the controller is in this

© Copyright 2024 ABB. All rights reserved. 17/26

state.
Workaround: To reset the controller state, open the Control Panel window and first switch to Manual
mode, and then back to Automatic mode.
Path handling of instructions with multiple joint targets
The path functions Rotate, Translate, and Mirror do not work as expected with instructions containing
via points as jointtargets. The functions will leave the jointtargets as is. Interpolate Path gives an
Unknown Error and Tool Compensation reports an error message.
Event Manager: Simulation cannot be triggered by analog system signals
The event manager only supports analog station signals, not analog system signals.
Conveyor Tracking
*Conveyor objects must be re-added for stations created prior to RS 6.05
When opening stations with conveyor tracking created prior to RobotStudio 6.05, conveyor objects
must be re-added.
Incorrect default values for c1Position and c1Speed for RobotWare 5 with the PaintWare option
The default values for the parameters c1Position and c1Speed may become incorrect for a virtual
controller system. The symptom is that its attribute values are all zero, see snapshot below.
Workaround: Save the following lines to a CFG file named ‘TEMP.CFG’ or similar and load in the virtual
controller followed by a restart.

EIO:CFG_1.0:5:0::
#
EIO_SIGNAL:
-Name "c1Position" -SignalType "AI" -Unit "CnvIf"\
-SignalLabel "ctPosition" -UnitMap "0-31" -Access "ALL"\
-MaxLog 21474.8 -MaxPhys 1 -MaxPhysLimit 1\
-MaxBitVal 2147483647 -MinLog -21474.8 -MinPhys -1 -MinPhysLimit -1\
-MinBitVal -2147483647
-Name "c1Speed" -SignalType "AI" -Unit "CnvIf" -SignalLabel "ctSpeed"\
-UnitMap "32-63" -Access "ALL"\
-MaxLog 21474.8 -MaxPhys 1 -MaxPhysLimit 1\
-MaxBitVal 2147483647 -MinLog -21474.8 -MinPhys -1 -MinPhysLimit -1\
-MinBitVal -2147483647

MultiMove
MultiMove error: ‘Object reference not set to an instance of an object’
When the Test Play button is pressed in the MultiMove tool, the following error message may be
displayed: ‘Object reference not set to an instance of an object’, but the robot moves and the Status
‘Calculation OK’ is displayed. In addition, when ‘Create Paths‘ is pressed the following message is
displayed: ‘Can't create paths : Value cannot be null’, and no paths are created. In the ‘Create Paths
Settings’, is the WP TCP drop down empty.
Reason: Workobject is not set for the current task.
External Axis
Error 50091: ‘Restart not possible’ after warm start of a system with external axis
When restarting a system with activated mechanical units the activation state is lost. Then the program

© Copyright 2024 ABB. All rights reserved. 18/26

can no longer be started from the Virtual FlexPendant, the RAPID Editor or the RAPID Tasks window.
Workaround: Reset the program pointer (‘Program Pointer to Main’) before starting the program from
the Virtual FlexPendant, the RAPID Editor or the RAPID Tasks window, or, start the program from the
Simulation Play button.
Network Drives and UNC Paths
RobotStudio on computers with roaming user profiles
RobotStudio may fail on PC configurations with roaming user profiles, i.e. when the users’ documents
folder resides on a server and not on the local disk.
Workaround: Redefine the ’User Project Folder’ to a folder on the local disk (File → Options → General →
Files&Folders → User Project Folder).
Virtual Controller does not support UNC paths
UNC paths cannot be used to locate Virtual Controller systems. Using UNC paths for VC systems will
cause the log message ‘Failed to initialize FW upgrade framework’ to appear when the system starts.
Subsequent attempts to work with the VC such as synchronizing RAPID data will fail.
Creating and starting systems located on a network drive
When using a network drive to store RobotStudio data such as RobotWare systems or the RobotWare
mediapool, the following problems may occur:
Virtual controller does not start
Not possible to open Virtual FlexPendant
Cause: By default, the .NET Framework does not allow execution of code from a remote file system. This
means the application may behave unexpectedly if the media used by the system or the system itself
resides on a network share.
Workaround: To resolve this, the user must explicitly grant the required permissions:
1. Open the file Virtual FlexPendant.exe.config located in C:\Program Files (x86)\ABB Industrial
IT\Robotics IT\RobotStudio 5.61\Bin
2. Add the following lines:

<?xml version="1.0"?>
<configuration>
<startup useLegacyV2RuntimeActivationPolicy="true">
<supportedRuntime version="v4.0" sku=".NETFramework,Version=v4.0"/>
</startup>
<runtime> <!-- THIS IS ONE OF THE NEW LINES!!! -->
<loadFromRemoteSources enabled="true"/> <!-- THIS IS ONE OF THE NEW LINES!!! -->
</runtime> <!-- THIS IS ONE OF THE NEW LINES!!! -->
</configuration>

The Virtual FlexPendant must be restarted for the changes to take effect. For further information, see
http://msdn.microsoft.com/en-us/library/dd409252(v=vs.100).aspx
RAPID
Robtargets that are LOCAL to a PROCEDURE cannot be synchronized with RobotStudio
The RobotStudio synchronization engine that translates 3D data of the station to RAPID code and vice

© Copyright 2024 ABB. All rights reserved. 19/26

versa does not support robtargets that are declared locally to a procedure.
Workaround: Declare the robtargets as global or local to a module instead.
Robtarget names must be unique in RAPID even if they are LOCAL
RobotStudio requires that robtarget names are unique for the RAPID synchronization to work properly,
i.e. you cannot have a global robtarget named pMyTarget1 in module A and a local robtarget with the
same name in Module B.
Global robtargets cannot be made local through Synchronization to VC
Global robtargets cannot be changed to local through Synchronization to VC, the option is disabled
(PDD 3140).
Workaround: Change the robtargets to module local in the RAPID Editor and Synchronize to station.
Error Message: Sync. to Station completed with errors
Error Message: Sync to Station completed with errors: New data name type has same name as existing
object in same block routine.
When this error message appears, there is a storage type mix-up between data already stored in RS and
in the VC. Because of this, and per design, the data is not considered the same data.
Workaround:
1. Ensure all data declarations have the same definition in RS as in RAPID (there is no user interface
for this).
2. Sync to station should now work.
3. Sync back to controller, and remember to change the data declarations back to what you want.
Paint
The new conveyor tracking module DSQC2000 is not supported for paint robots.
The new conveyor tracking module DSQC2000 is not supported for paint robots.
Lack of Virtual Controller support for the Paint systems
Paint systems that are configured using the Paint package I/O option Discrete, Compact or Fieldbus,
will result in a SysFail state.
Workaround: Re-create the system with the simulated I/O option.
Graphics and Geometry
*Display of working range optimized for furthest reach
The current algorithm uses a fixed value for joint five which gives the furthest reach for a given tool. The
sweep is not optimized to get the shortest reach on the "inside" of the working area.

© Copyright 2024 ABB. All rights reserved. 20/26

Enforce selected graphics device for PCs with multiple graphics cards
For best performance when running RobotStudio on a PC with multiple graphics cards, RobotStudio can
be configured to use a specified device. By this option you can ensure maximum performance. This is
useful for e.g. Lenovo W540 that has both an integrated Intel graphics device and a discrete NVIDIA
card.
Open the file RobotStudio.exe.config that is located in the folders
C:\Program Files (x86)\ABB Industrial IT\Robotics IT\RobotStudio x.y\Bin64
and
C:\Program Files (x86)\ABB Industrial IT\Robotics IT\RobotStudio x.y\Bin
and uncomment the line:

<add key="GraphicsDeviceType" value="Discrete"/>

Valid values are 'Discrete', 'Integrated' and 'Warp' (software renderer). Note that there are two different
files, one for the 32-bit version, and another for the 64-bit version.
Problems when undoing Boolean operations on Geometry
Undoing a Boolean operation might not succeed. To recover from these problems, you need to delete
the items that caused the problem.
ScreenMaker
Numeric controls and decimal separators
To use numeric controls in ScreenMaker on the PC set the decimal symbol to a single period ('.'). Other
decimal symbols are not supported and binding values will not work in the Virtual FlexPendant. The
behavior on the real FlexPendant is not affected by this PC setting.
Graphs on secondary screens
To use a Graph on a secondary screen (not the main screen) a custom action is needed. Otherwise, the
Graph will not be updated properly. In the ScreenForm that contains the Graph add a Load event. In this
event add an action using Add Action->Advanced->Call Custom Action. Select the Graph control and the
UpdateValues action.

© Copyright 2024 ABB. All rights reserved. 21/26

Binding to the Enabled property
Connecting the Enabled property of any control to a BOOL variable or IO signal may not work as
expected. The variable or signal may be inadvertently changed leading to unexpected behavior. Instead,
bind to a digital output where the Access Level is set to ReadOnly
A ScreenMaker cannot be deployed a controller with disabled Default User
Workaround: Enable the Default User.
NumEditor in ScreenMaker disables the controls in a group box or panel
If you are using the NumEditor control in a group box or a panel, and that box or panel is enabled by an
input signal, then all other controls of that group or panel will become disabled if the editor is opened
and closed.
Button with multiple states in ScreenMaker app do not update the images if button is disabled
For an app which uses Buttons with multiple states connected to images that change depending on the
value of a RAPID variable, then if the button is disabled, the button shows the greyed image of the state
which was active when the disabled state was shown the first time.
ScreenMaker fails for RobotWare 5.12
ScreenMaker fails to build applications for RobotWare 5.12.
Workaround: Update to a later RobotWare version.
A ScreenMaker application may fail to build if the DPI setting is not set to 100%
Certain UI controls in ScreenMaker may fail to build correctly if the DPI setting is not set to ‘Smaller –
100%’.
Symptom: The error message caused by this problem will read ‘System.Drawing.Font’ does not contain a
constructor that takes 2 arguments.
Workaround: Set DPI to 100% on your PC.
File changes to FlexPendant applications does not load the changes until a FlexPendant reset
With RobotWare 6.0x the controller's restart will no longer reset the FlexPendant memory. This was part
of an effort to improve the restart time of the controller. This means that after placing a new

© Copyright 2024 ABB. All rights reserved. 22/26

FlexPendant application file(s) on the FlexPendant unit, you need to manually reset the FlexPendant for
it to reload its assets.
To manually reset the FlexPendant you need to use the reset button on the FlexPendant's backside. (See
Operating Manual – IRC5 with FlexPendant, 3HAC16590)
Running Routine with Movement
RunRoutine Button control does not always work correct when a routine with movements is called. As a
workaround use instructions like StopMove, StorePath, RestorePath and StartMove to control the
movements of the robot. A Trap routine could be called with a normal button control and in the Trap the
above instructions can be used to control the movements of the robot.
PictureBox control as a Widget
If a Picture Box control is created as a widget from a Windows 8 operating system, the control is not
shown on the FlexPendant. The behavior is fine with any other operating system like Windows 7.

© Copyright 2024 ABB. All rights reserved. 23/26

RobotWare Compatibility
Supported RobotWare versions
RobotStudio works with RobotWare 5.07 and later. Please check details below. The latest supported
RobotWare version for IRC5 and OmniCore controllers is stated under Help/About in RobotStudio.
RobotWare packages can be added to RobotStudio from the Add-Ins Gallery window.
RobotWare 5.05 and 5.06 Compatibility
RobotWare 5.05 and 5.06 including revisions thereof are not supported by RobotStudio 5.15 and later
versions. Please use the corresponding version of RobotStudio for managing robot controllers with any
of these RobotWare versions.
RobotWare 5.07 Compatibility
General
The location of the program pointer is not updated in the RAPID Editor during program execution.
Offline
A limitation in the versions 5.07.02, 5.07.03, and, 5.07.04 of RobotWare may cause the Virtual Controller
to System Failure state during I-start on certain computers. The problem is due to the ctrl.bin-file not
being correctly created.
Workaround: Create an empty ctrl.bin file in the INTERNAL folder of the controller system, and then
perform a warm start.
Note: The problem will reappear if the system is I-started. The virtual controller does not support
RobotWare 5.07.08 and RobotWare 5.07.07.
Online
FlexPendant Viewer does not work RobotWare 5.07.
RobotWare 5.08 Compatibility
RobotWare 5.08 and its revisions of are supported with the following limitations:
Offline
RobotWare 5.08 is not supported.
Workaround: Use RobotWare 5.08.01 or later.
RobotWare 5.10 Compatibility
RobotWare 5.10 and its revisions of are supported with the following limitations:
Offline
Starting a controller will generate internal UAS error in controller error log.
RobotWare 5.11 Compatibility
RobotWare 5.11 and its revisions of are supported with the following limitations:
Offline
Linear jogging of a robot across joint values that will cause a change of confdata may fail. For example,
if the robot is jogged linearly when joint values is passing 90 degrees for axis 1 may cause the robot to
stop or to change configuration.

© Copyright 2024 ABB. All rights reserved. 24/26

RobotWare 5.12 Compatibility
RobotWare 5.12 and its revisions of are supported with the following limitations:
Paint
Paint backups from RW 5.12.01 are not compatible with RW 5.12.02 or later. Restoring a paint system
backup from RobotWare 5.12.01 will cause SysFail for RobotWare 5.12.02 or later.
Workaround: Add the following parameters to the configuration files:
EIO.CFG

EIO_SIGNAL:
-Name "doMainInMC" -SignalType "DO" -Unit "SysComm" -UnitMap "44"
-Name "A1HVErrNo" -SignalType "GO" -Unit "SysComm" -UnitMap "150-151"\
-Access "ALL"
-Name "A1HVEn" -SignalType "DO" -Unit "SysComm" -UnitMap "155"\
-Access "ALL"

EIO_CROSS:
-Res "A1HVEn" -Act1 "HVEnabled"

SYS.CFG:

CAB_TASK_MODULES:
-File "INTERNAL:/pntrapid/T_ROB1/cycinfo.sys" -ModName "cycinfo"\
-Task "T_ROB1"
-File "INTERNAL:/pntrapid/csvlkup.sys" -ModName "csvlkup" -AllTask \
-Hidden

RobotWare 5.13 Compatibility

RobotWare 5.13 and its revisions of are supported with the following limitations:
Paint
Paint backups from RW 5.12.02, 5.12.03 or RW 5.13 or 5.13.01 not compatible with RW 5.13.02 or RW
5.13.03. There are several changes in the configuration database for I/O (EIO.CFG) and Controller
(SYS.CFG) that will cause System Failure if an old backup is loaded. There are also changed in installed
RAPID modules. To create a compatible configuration, proceed as follows:
1. Create and start a VC with a RobotWare 5.13.03 system containing the same options as your
original backup, but do not load the backup.
2. Save the EIO.CFG and SYS.CFG to file.
3. Compare the saved files with the corresponding files of your backup. (You can use a text file
comparison tool for simplification.)
4. Add your system-specific configuration to the general configuration files saved from the 5.13.01-
system using a text editor.
5. Replace the files of the original backup with the corresponding modified configuration files.
6. Go through the RAPID modules of the backup and remove the default modules (i.e. those that are
not changed by the user).
7. Load the backup and restart the system. You are done.
RobotWare 5.15 Compatibility
Signal Analyzer Online
The feature Signal Analyzer Online requires RobotWare 5.15.03 or later.

© Copyright 2024 ABB. All rights reserved. 25/26

RobotWare 6 Compatibility
Overview
RobotWare 6.00 and 6.00.01 systems cannot be directly upgraded to RobotWare 6.01. To upgrade a
system, you need to create backup and migrate it using the tool ‘Migrate Backup or Folder’, then
recreate the system and finally, restore the backup. For this reason, the functions ‘Unpack&Work’, ‘Go
Offline’ and ‘New Solution with Station and Robot Controller – From backup’ are blocked to prevent
upgrade from RobotWare 6.00 or 6.00.01 to RobotWare 6.01. RobotStudio, however, is compatible with
both RobotWare 6.00 / 6.00.01 and 6.01.
General Compatibility Limitations
Safety Configuration
Safety configuration of a track motion IRC5 system equipped with a safety controller of type EPS or
SafeMove can be done without the need to read track motion parameters manually when using
RobotWare 5.11.01 or later. Encrypted parameters needed by the safety controller will be automatically
read by EPS Wizard and SafeMove Configurator, respectively.
Configurations
The feature Configurations for selecting the robot arm configuration (confdata) may fail, or not present
all solutions, in some specific circumstances even when the target is reachable if RobotWare 5.14 or
earlier is used.
Workaround: Upgrade to RW5.14.01 or later

© Copyright 2024 ABB. All rights reserved. 26/26