LAPORAN HASIL PEMERIKSAAN OQC Apprval

PT. Strange Tech

Prepared by Verified by Approved by

/ Cikarang Indonesia
PT. Heesung
OQC INSPECTION RESULT REPORT
DCC Electronics

PT. Strange Tech Cikarang Product

Supllier Tanggal Pemeriksaan / PIC / Alat Ukur / Kondisi Pengukuran /
Indonesia Name Aging
Customer
Lot Qty Standart
Model Checking Date Inspector Meass Instrument Meassure Condition
Number Sampling

Part No Lot Size Ea PT. Heesung Electronics 3D 20 ℃/ ,58%

Item Checks Specification pemeriksaan Tingkat AQL X1 X2 X3 X4 X5 NG Qty

• Based on the packaging quantity by

OK 0
model/sealed packaging

• No abnormality in excess loading and

OK 0
cleanliness in and out of the box

• No deformation of the product due to Box

Packing Inspection OK 0
dropping
n=1 c=0
• No mis-attachment and reversed loading on
OK 0
the products

• Check Mark "RoHS" or UL at Label OK 0

* Based on regulated drawing (receive supplier

Material Inspection OK 0
approval)

* Based on Good Board and Drawing (stabbed,

Form Inspection OK OK OK OK OK 0
unshape, eccentricity )

* Foreign material quality, Black spot

(D>=0.2mm: NG D <0.2mm: 1 OK) → OK OK OK OK OK 0
Foreign Material / Burr Based on model standard
• No Burr on edge/border (mold cut surface),
OK OK OK OK OK 0
no foreign material

* No S/C black spots, white spots, white wires,

OK OK OK OK OK 0
bright lines, etc.
Scratch / Stabbed
(Limit sample comparison confirmation at the
OK OK OK OK OK 0
time of mass production approval)

Black line, white line, * No black lines, white lines, stains, or bright
OK OK OK OK OK 0
stain, bright line lines

Pressing, White spot,

* No Pressing, White spot, crumple, wrinkle OK OK OK OK OK 0
crumple, wrinkle

Appearance Inspection Coating Inspection * should be coating and no peel off OK OK OK OK OK 0

GII c=0

Hole Inspection * No Hole Chip / Hole blocked OK OK OK OK OK 0

* No scratches, dents, stains, compression,

0
creases or wrinkles

* Uncoated, coating will not peel off 0

Protective film
inspection
* Hole Chip / Hole must not be clogged 0

* The protective film must not be attached or

0
peeled off.

* Check drawing spec by model OK OK OK OK OK 0

Bending Inspection
* No Sheet Crumple "S" letter bending OK OK OK OK OK 0

* No phenomenon on moire, mark, scratch,

Lighting Inspection OK OK OK OK OK 0
crumple

* Assembly condition normal → When do

Assembly Test n=3 c=0 0
shaping the related products no abnormality

Check surface resistance use surface

10^7.8 0
resistance meter (spec 10¹²↓) "FRONT"
Anti static treatment n=1 c=0
Check surface resistance use surface
10^7.8 0
resistance meter (spec 10¹²↓) "BACK"

* Measurement based on hazardous material

Environment Friendly - - 0
management standard
spesifikasi
Item Checks Tingkat Pemeriksaan AQL X1 X2 X3 X4 X5 NG Qty
Min Type Max
CTQ 1-1 X inline Top 1,433.62 1,433.72 1,434.22 1433.65 1433.7 1433.72 1433.65 1433.67 0
CTQ 1-2 X inline Middle 1,433.62 1,433.72 1,434.22 1433.65 1433.67 1433.7 1433.72 1433.68 0
CTQ 1-3 X inline Bottom 1,433.62 1,433.72 1,434.22 1433.75 1433.71 1433.74 1433.72 1433.7 0
CTQ 25-1 Y inline Left 812.35 812.55 812.75 812.48 812.52 812.54 812.5 812.48 0
CTQ 25-2 Y inline Middle 812.35 812.55 812.75 812.55 812.5 812.49 812.52 812.55 0
CTQ 25-3 Y inline Right 812.35 812.55 812.75 812.51 812.53 812.5 812.48 812.49 0
* 24-1 X Middle to Left 405.46 405.56 405.66 405.57 405.59 405.55 405.58 405.61 0
* 24-2 X Middle to Left 405.46 405.56 405.66 405.55 405.53 405.56 405.55 405.57 0
* 24-3 X Middle to Left 405.46 405.56 405.66 405.53 405.56 405.52 405.54 405.53 0
* 2-1 Y Middle to Top 716.81 716.86 717.11 716.83 716.82 716.84 716.85 716.83 0
* 2-2 Y Middle to Top 716.81 716.86 717.11 716.81 716.84 716.82 716.83 716.85 0
* 2-3 Y Middle to Top 716.81 716.86 717.11 716.82 716.84 716.84 716.81 716.83 0

GII C=0

39 Thickness 0.295 0.315 0.335 0.312 0.311 0.316 0.313 0.317 0

* 37 Warp Longside 0.00 0.00 2.00 0.5 0.5 0 0 0.5 0
* 38 Warp Shortside 0.00 0.00 2.00 0 0 0 0 0 0
Angle UP 15.00 16.00 17.00 16.54 16.33 16.11 16.54 16.84 0
Angle Down 105.00 106.00 107.00 106.11 106.52 106.33 106.48 106.19 0
No. Perubahan No Lot Qty (pcs) No Lot Qty (pcs) No Lot
1
2
3
4
5
Approved by

Keputusan /

Decision

OK

Keterangan

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

OK

No Used

No Used

No Used

No Used

OK

OK

OK

No Used

OK

OK

No Used

Keterangan

OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK

OK
OK
OK
OK
OK
No Lot
 Apprval Prepared by Verified by Approved by
LAPORAN HASIL PEMERIKSAAN OQC / PT. Strange Tech
Cikarang Indonesia
OQC INSPECTION RESULT REPORT PT. Heesung
DCC Electronics

PT. Strange Tech Cikarang

Supllier Product Name 65UA75 / Reflector Sheet Tanggal Pemeriksaan / PIC / Alat Ukur / Kondisi Pengukuran / Keputusan /
Indonesia Aging
Customer
Standart
Model HC650DQG-ABEA1 Lot Number 006-B-B06-160125 Qty Sampling Checking Date Inspector Meass Instrument Meassure Condition Decision

Part No LC65501095A Lot Size 30 Ea 0/8 PT. Heesung Electronics 1/23/2025 ADI 3D 20 ℃/ ,58% - OK

Item Checks Specification pemeriksaan Tingkat AQL X1 X2 X3 X4 X5 NG Qty Keterangan

• Based on the packaging quantity by model/sealed packaging OK 0 OK

• No abnormality in excess loading and cleanliness in and out of

OK 0 OK
the box

Packing Inspection • No deformation of the product due to Box dropping OK 0 OK

n=1 c=0
• No mis-attachment and reversed loading on the products OK 0 OK

• Check Mark "RoHS" or UL at Label OK 0 OK

Material Inspection * Based on regulated drawing (receive supplier approval) OK 0 OK

* Based on Good Board and Drawing (No hole blocked and

Form Inspection OK OK OK OK OK 0 OK
molded)

Foreign Material / Burr * No foreign substances, dark spots or foreign substances OK OK OK OK OK 0 OK

* No stains, contamination, tears, creases or wrinkles

OK OK OK OK OK 0 OK
→ OK if there is no problem with the image

Stain / Pollution * Pollution size (D> = 0.25mm: NG D <0.25: 1a OK) OK OK OK OK OK 0 OK

* Contamination from cutting part OK OK OK OK OK 0 OK

* None
Scratch / Stabbed → Perform individual sheet judgment and determine BLU when OK OK OK OK OK 0 OK
defective is detected (nothing)

Overprint * Based on drawing regulation OK OK OK OK OK 0 OK

* No convex/concave shapes OK OK OK OK OK 0 OK

* Sheet must not be folded (including Shape “S”) OK OK OK OK OK 0 OK

* Flatness Curl (Cup, Cap) / Wave must be less than 2.0㎜ → If the
specifications are specified in the drawing, follow the drawing OK OK OK OK OK 0 OK
Bending Inspection
specifications.
* Only positive curls are judged after measuring the end of the 4-
OK OK OK OK OK 0 OK
point corner.
Appearance
Inspection * Determination after measuring the Max value between the long
and short sides of the wave (however, there should be no blur on n=5 c=0 OK OK OK OK OK 0 OK
the screen)

Coating Inspection * should be coating and no peel off OK OK OK OK OK 0 OK

Hole Inspection * No Hole Chip / Hole blocked OK OK OK OK OK 0 OK

* No over-cutting/under-cutting OK OK OK OK OK 0 OK
Half Cutting Inspection
* Cutting ratio no abnormality OK OK OK OK OK 0 OK

* No abnormality on tape specifications (Material, Size) 0 Not Used

Tape Ass'y Inspection * No tape missing and mis-attachment 0 Not Used

* No tape damage and no cutting side foreign material 0 Not Used

* No print smudges, eccentricities, no missing OK OK OK OK OK 0 OK

* No DOT dropping OK OK OK OK OK 0 OK
Print Inspection
(Print Model) * Dot Attachment Power Inspection
→ Attach the tape, then scrub back and forth 10times. When
OK OK OK OK OK 0 OK
exfoliate slowly 90degree, no Dot dropping
(Up, Down, Left, Right 4Point Checking)

Lighting Inspection * No phenomenon on moire, mark, scratch, crumple OK OK OK OK OK 0 OK

Assembly Test * There will be no problem when fastening to the cover bottom. - - 0 Not Used

Check surface resistance use surface resistance meter (spec

10^7.8 0 OK
10¹²↓) "FRONT"
Anti static treatment n=1 c=0
Check surface resistance use surface resistance meter (spec
10^7.8 0 OK
10¹²↓) "BACK"
* Measurement based on hazardous material management
Environment Friendly - - 0 Not Used
standard
spesifikasi
Item Checks Tingkat Pemeriksaan AQL X1 X2 X3 X4 X5 NG Qty Keterangan
Min Type Max
CTQ 1-1 X inline Top 1,445.92 1,446.22 1,446.52 1446.17 1446.19 1446.15 1446.17 1446.16 OK
CTQ 1-2 X inline Middle 1,445.92 1,446.22 1,446.52 1446.12 1446.16 1446.14 1446.15 1446.11 OK
CTQ 1-3 X inline Bottom 1,445.92 1,446.22 1,446.52 1446.09 1446.11 1446.08 1446.05 1446.07 OK
CTQ 33-1 Y inline Left 820.07 820.37 820.67 820.31 820.29 820.35 820.32 820.31 OK
CTQ 33-2 Y inline Middle 820.07 820.37 820.67 820.36 820.34 820.37 820.35 820.34 OK
CTQ 33-3 Y inline Right 820.07 820.37 820.67 820.41 820.43 820.45 820.44 820.42 OK
* 2-1 X Half to Left 723.01 723.11 723.21 723.08 723.07 723.04 723.06 723.03 OK
* 2-2 X Half to Left 723.01 723.11 723.21 723.12 723.13 723.15 723.12 723.14 OK
* 2-3 X Half to Left 723.01 723.11 723.21 723.09 723.11 723.11 723.13 723.11 OK

* 27-1 Y Half to Top 408.29 408.39 408.49 408.37 408.35 408.38 408.36 408.35 OK

* 27-2 Y Half to Top 408.29 408.39 408.49 408.36 408.34 408.35 408.32 408.33 OK
n =5 C=0
* 27-3 Y Half to Top 408.29 408.39 408.49 408.38 408.37 408.34 408.36 408.34 OK

Thickness 0.178 0.188 0.198 0.187 0.188 0.186 0.185 0.189 OK

Warp Longside -3.00 0.00 0.00 0 0 0 0 0 OK
Warp Shortside -3.00 0.00 0.00 0 0 0 0 0 OK
No. Perubahan No Lot Qty (pcs) No Lot Qty (pcs) No Lot
1 006-B-B06-160125 30
2
3
4
5
 Apprval Prepared by Verified by Approved by
LAPORAN HASIL PEMERIKSAAN OQC / PT. Strange Tech
Cikarang Indonesia
OQC INSPECTION RESULT REPORT PT. Heesung
DCC Electronics

SPEC

MAF66396801 - LZ10221101A(32") : W : 820 H : 550

PT. Strange Tech Cikarang Tanggal Pemeriksaan / PIC / Alat Ukur / Kondisi Pengukuran / Keputusan /
Supllier Product Name Al-Bag Customer
Indonesia Checking Date Inspector Meass Instrument Meassure Condition Decision

Model 32 inch Lot Number 1/15/2025 Qty Sampling Roll Meter 20 ℃,

PT. Heesung Electronics 24-01-2025 Diah OK
Part No LZ10221101A Lot Size 4000 Ea 0/200 Field Meter 58%

Item Checks Specification pemeriksaan Tingkat AQL X1 X2 X3 X4 X5 NG Qty Keterangan

* Based on the packaging quantity by model/sealed

OK 0 OK
packaging/Wrapping condition normal

* Rack inside/outside is clean

Packing Inspection → Not get too much contamination/pollution when cleaning OK 0 OK
without progress n=1 c=0

• Check Mark "RoHS" or UL at Label OK 0 OK

Material Inspection * Based on regulated drawing (receive supplier approval) OK 0 OK

Dirty * None OK OK OK OK OK 0 OK

Torn * None OK OK OK OK OK 0 OK

Folded * None OK OK OK OK OK 0 OK
Appearance
n=5 c=0
Inspection Burr or wringkles in sealing
* None OK OK OK OK OK 0 OK
and No Holes

Foreign Material * None OK OK OK OK OK 0 OK

Printing * None OK OK OK OK OK 0 OK

* Check surface resistance use surface resistance meter (spec

Surface Resistance n=1 C=0 10^8.0 OK OK OK OK 0 NG
10¹¹↓)

ESD Test * Check Test (spec 100V↓ or specific drawing) n=1 C=0 10^8.0 0 OK

* Measurement based on hazardous material management

Environment Friendly - - 0 OK
standard
spesifikasi
Item Checks Tingkat Pemeriksaan AQL X1 X2 X3 X4 X5 NG Qty Keterangan
Min Type Max

CTQ Width 818.00 820.00 830.00 820.52 820.59 820.23 820.32 820.45 0 OK

CTQ Height 548.00 550.00 560.00 550.56 550.40 550.26 550.64 550.54 0 OK

CTQ Open side 2.00 5.00 8.00 5.19 5.15 5.30 5.32 5.35 0 OK
n =5 C=0
CTQ Pressure Sealing 5.50 7.00 8.50 7.22 7.15 7.17 7.66 7.55 0 OK

CTQ Pressure Sealing 5.50 7.00 8.50 7.24 7.53 7.29 7.18 7.50 0 OK

CTQ Pressure Sealing 5.50 7.00 8.50 7.18 7.22 7.15 7.17 7.23 0 OK

No. Perubahan No Lot Qty (pcs) No Lot Qty (pcs) No Lot

1 1/15/2025 4000
2
3
4
5