Scribd
Upload
13 views

FINAL EXAM _CKTS2_2022 modified

This document is an exam paper for the Electronics and Communication Engineering Program at Adama Science and Technology University, dated August 12, 2022. It consists of three parts: multiple choice questions, discussion questions, and workout problems, covering topics related to electronic circuits. The exam has specific instructions regarding handwriting, assumptions, and academic integrity.

Uploaded by

edosa misgenu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
13 views

FINAL EXAM _CKTS2_2022 modified

This document is an exam paper for the Electronics and Communication Engineering Program at Adama Science and Technology University, dated August 12, 2022. It consists of three parts: multiple choice questions, discussion questions, and workout problems, covering topics related to electronic circuits. The exam has specific instructions regarding handwriting, assumptions, and academic integrity.

Uploaded by

edosa misgenu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

[DOCUMENT TITLE]

Adama Science and Technology University


School of Electrical Engineering and Computing
Electronics and Communication Engineering Program

Final-Exam

Exam Date: AUG. 12, 2022 Time allotted: 2:30 hours


ECEg 2202: Electronic Circuit II Total Marks: 35%

Name: ____________________________________________________________
ID: ____________________________________________________________

GROUP: YEAR: 2nd

Instructions:
1. Please check whether the exam paper contains three parts, part I , part II and part-III.
2. You can use any assumption if necessary and state your assumption
3. If your handwriting is not understandable marks will not be awarded
4. Clear and neat answer is worthy.
5. Do not use pencil and red pen.
6. Any kind of cheating/malpractice during exam will lead to cancellation of whole examination

For instructors use only

Part-I&II Part-III
Total
Questions 1-7 1 2 3 4 5
Weight 11 5 4 6 3 6 35
Score

All the best!!!


Part I: MULTIPLE CHOICE QUESTIONS
1. A Differential Amplifier amplifies
A. Input signal with higher voltage
B. Input voltage with smaller voltage
C. Sum of the input voltage
D. None of the Mentioned
2. What is the output waveform by considering input as rectangular waveform

A. sine wave
B. square wave
C. sawtooth wave
D. triangle wave

3. In an LC oscillator, if the value of L is increased four times, the frequency of oscillations is …

A. Increased 2 times
B. Decreased 4 times
C. Increased 4 times
D. Decreased 2 times

4. The ________ can conduct current in either direction and is turned on when a breakover
voltage is exceeded.
A. SCR
B. Diac
C. UJT
D. Triac
5. Which of the following is (are) power amplifier
A. Class A
B. Class B or AB
C. Class C or D
D. All the above
Adama Science and Technology University
School of Electrical Engineering and Computing
Electronics and Communication Engineering Program

Part II: Discussion


6. State the four topologies of feedback amplifier, draw the block diagram for each topology,
and write the expression for the feedback factor β and the transfer gain A. [3p]
7. Write at least six comparisons of an ideal and practical operational amplifier (Op-amp)
characteristics? [3p]

Part III: WORKOUT

1) A three-stage OP-amp circuit is required to provide voltage gains of +10, –18 and –27.
Design the OP-amp circuit. Use a 270 kΩ feedback resistor for all three circuits. What
output voltage will result for an input of 150 µV? [5p]

2) A 1 pF capacitor is available. Calculate the inductor values in a Hartley oscillator so that


f = 1 MHz and β= 0.2. and find the open loop gain? [4p]

3) The output of an op-amp integrator can swing from +12 V to −12 V. The step input
shown in below is vi = 0 for t < 0 and switched at t = 0 to 5 V. The output voltage vo =
+12 V for t < 0. Plot the waveform. [6p]

4) in an astable 555 configuration, the external resistor R1=3.3kΩ. What must the value of
R2 to produce a duty cycle of 50 percent? [3p]
5) Power (brightness) of a 100W, 110 V tungsten lamp is to be varied by controlling the
firing angle of an SCR in a half-wave rectifier circuit supplied with 110 Va.c. find the
following parameter [6p]

A. DC voltage,
B. B) DC power, are developed in the lamp at firing angle α= 60°?

You might also like