Scribd
Upload
36 views3 pages

Industrial Midterm Exam

This document is a mid-term exam for the Industrial Electronics course at Beni-Suef University, consisting of multiple-choice questions and descriptive problems related to electrical engineering concepts. It covers topics such as amplifiers, converters, and circuit behavior, with a total of 15 questions in the first section and additional questions in subsequent sections. The exam is designed to assess students' understanding of industrial electronics principles and applications.

Uploaded by

Asmaa A-Elghany
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views3 pages

Industrial Midterm Exam

This document is a mid-term exam for the Industrial Electronics course at Beni-Suef University, consisting of multiple-choice questions and descriptive problems related to electrical engineering concepts. It covers topics such as amplifiers, converters, and circuit behavior, with a total of 15 questions in the first section and additional questions in subsequent sections. The exam is designed to assess students' understanding of industrial electronics principles and applications.

Uploaded by

Asmaa A-Elghany
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Beni-Suef University Faculty of Engineering Electrical Engineering Dept.

Subject: Industrial Electronics Mid-Term Exam Time: 1.5 hrs

Question (1): (15 Marks)


Select the correct answer from those given:
1. Refer to Figure , The purpose of 𝑅1 𝑎𝑛𝑑 𝑅2 is:
(a) For bias current compensation.
(b) For input offset voltage compensation.
(c) To set input impedance.
(d) To set input impedance and voltage gain.
2. A voltage- follower amplifier comes to you for service. You find the voltage gain to be 5.5
and the input impedance 2.2 𝑘Ω. The probable fault in this amplifier, if any, is
(a) The gain is too low for this type of amplifier.
(b) the input impedance is too high for this amplifier.
(c) Nothing is wrong. the trouble must be somewhere else.
(d) None of these.
3. A current- to- voltage converter produces a
(a) Constant output voltage for variable input current.
(b) Variable output voltage for constant input current.
(c) Proportional output voltage for variable input current.
(d) Proportional output current for variable input voltage.
4. Transconductance is the ratio of the output.
(a)Current to the input voltage. (b) Current to the input current.
(c)Voltage to the input voltage. (d)Voltage to the input current.
5. In a flash A/D converter, the priority encoder is used to
(a) Select the first input. (b)Select the highest value input.
(c)Select the lowest value input. (d)Select the last input.
6. A good example of hysteresis is a(n)
(a)AM radio. (b)Thermostat.
(c)Alarm clock. (d)None of the above.
7. Refer to Figure, a square wave input is applied to this amplifier, the output voltage is
most likely to be:
(a) A square wave. (b)A triangle wave.
(c)A sine wave. (d)No output.

8. Refer to Figure in problem 7, if Vin= 5V, the rate of change of the


output voltage in response to a single pulse input is:
(a)15.2 𝑚𝑉/𝜇𝑠 (b)1.52 𝑚𝑉/𝜇𝑠
(c)1.52 𝑚𝑉/𝜇𝑠 (d)15.2 𝑉/𝜇𝑠

Dr. Asmaa A-Elghany Page 1 of 3


9. Refer to Figure, determine the lower trigger point.
(a)+ Vout(max) (b) Vout(max)
(c)2.47 V (d)+ 2.47 V
10. Refer to problem 9, determine the upper trigger point.
(a) + Vout(max) (b) - Vout(max)
(c) -1.41 V (d) + 1.41 V
11. If 𝑉1 = −2 𝑉, then output 𝑉𝑜 is:
(a)−6 𝑉 (b) 6 𝑉
(c)−3 𝑉 (d) 3 𝑉
12. If the output of a CMOS inverter gets accidently shorted to ground
(a) The n-channel driver MOSFET will be damaged.
(b) The supply voltage source will be damaged.
(c) The current drain for the supply will increase, which may damage the p-channel load
MOSFET.
(d) None of these will happen.
13. The Boolean equation for Y in the following circuit is
(a)𝑌 = (𝐴(𝐵 + 𝐶) + 𝐷)′ (b)𝑌 = 𝐴(𝐵 + 𝐶) + 𝐷
′
(c)𝑌 = 𝐴(+𝐵𝐶)𝐷 (d)𝑌 = ((𝐴 + 𝐵𝐶)𝐷)
14. When the positive voltage on the gate of a P-channel JFET is increased, the drain current
will:
(a)Remain same (b) Decrease
(c)Increase (d)Any of the above
15. When a JFET is cut off, it’s like a(an)……. Switch and when it is saturated, it’s like a(an)
……. Switch.
(a)Closed, closed (b)Open, closed
(c)Open, open (d)Closed, open

Question (2): (20 Marks)


1. Explain a current-to-voltage converter.
𝑉
2. Obtain the value of 𝑅𝐴 such that 𝑉𝑜 = 32 − 2𝑉1

3. Draw the output voltage waveform for each circuit in Figure with respect to the input.
Show voltage levels.

Dr. Asmaa A-Elghany Page 2 of 3


Question (3): (15 Marks)
1. Discuss in detail examples of comparator applications.
2.(a) Determine the rate of change of the output voltage in response to the input square
wave, as shown for the practical integrator in Figure. Assume steady state conditions
have been reached. The input is a 1.0 kHz, 5 Vpp square wave centered at 0 V. (b)Draw
the output waveform.

Dr. Asmaa A-Elghany Page 3 of 3

You might also like